Expt 4-Estimation of Copper PDF
Expt 4-Estimation of Copper PDF
Expt 4-Estimation of Copper PDF
Theory: This experiment comes under the category of iodometry which is used widely in the
analysis of ores, alloys etc.
When an excess of KI is added to the solution containing Cu2+ in neutral or slightly acidic
medium, quantitative liberation of iodine takes place.
2CuI2 Cu2I2 + I2
This liberated iodine is then titrated against standard Na2S2O3 solution using starch solution as
indicator near the end point.
2Na2S2O3 + I2 Na2S4O6 + 2NaI
Ionic equation will be:
2Cu2+ + 2I Cu22+ + I2 + 2e
I2 + 2S2O32 + 2e S4O62 + 2I
From the above equation it is evident that
2Cu2+ I2 2S2O32 2e
The equivalent weight of Cu2+ will be one half of twice the molecular weight since the reaction
involves two electrons per two moles of Cu2+.
Eq. wt. of Cu2+ = (2 x 63.5) / 2 = 63.5
The titration fails when any mineral acid is present in the solution and therefore before
commencing the titration the acid should be neutralized. This is done by dropwise addition of
NH4OH until a slight blue precipitate just appears.
H+ + OH H2O
2NH4OH + Cu2+ 2NH4+ + Cu(OH)2
blue precipitate
The precipitate can be removed by addition of CH3COOH in the solution.
Cu(OH)2 + 2CH3COOH Cu2+ + 2CH3COO + 2H2O
Moreover, the precipitate of Cu2I2 absorbs I2 from the solution and releases it slowly making the
detection of sharp end point difficult. So, a small amount of NH4SCN is added near the end point
to displace the absorbed iodine from Cu2I2 precipitate.
Apparatus: Burette, pipette, beakers, conical flask, burette stand and clamp.
Chemicals: K2Cr2O7, Na2S2O3.5H2O, CuSO4.5H2O, NaHCO3, KI, NH4OH, CH3COOH,
starch, NH4SCN, HCl.
Procedure:
1. Standard K2Cr2O7 solution (0.1 N) is provided.
2. Sodium thiosulphate and copper sulphate solution of unknown strength were supplied.
3. Standardization of sodium thiosulphate (Na2S2O3) solution with standard K2Cr2O7
solution Take 40 mL of water in a 250 mL conical flask. To that add 20 mL of potassium
iodide (KI) solution (10%) and 1 g of sodium bicarbonate (NaHCO3). Add 6 mL of
concentrated hydrochloric acid (HCl) to the above solution and finally add 20 mL of
standard K2Cr2O7 solution using a pipette. Shake the flask and keep it covered with watch
glass in dark for 35 minutes. Titrate the liberated iodine with Na2S2O3 solution taken in
burette. When the colour of the solution fades to straw yellow, add few drops of starch
solution and continue the titration till the colour of the solution changes from deep blue to
bluish green. Repeat the titration three times.
4. Estimation of copper Pipette out 20 mL of solution in a 250 mL conical flask and
neutralized the solution by dropwise addition of ammonium hydroxide (NH4OH) solution
(1:1) until a blue precipitate appears. Dissolve the precipitate in acetic acid (CH3COOH)
adding about 0.5 mL in excess. Dilute the solution to about 80 mL and add 20 mL of
potassium iodide solution (10%). Keep the flask covered with watch glass in a dark and
cool place for about 35 minutes and titrate the liberated iodine with standard sodium
thiosulphate solution form burette. When the colour of the solution fades to a light yellow,
add few drops of starch followed by 20 mL of ammonium thiocyanate (NH4SCN) solution
(10%). Titrate the solution till the blue colour discharges and a white or flesh white residue
is left in the flask. Repeat the titration three times.
Observations:
Table 1 Standardization of Na2S2O3 solution with standard K2Cr2O7 solution
Strength of K2Cr2O7 solution = 0.1(N)
Calculations:
A) Standardization of Na2S2O3 solution with standard K2Cr2O7 solution
V1 x S1 = V2 x S2
S2 = (V1 x S1) / V2
B) Estimation of copper
1000 mL of 1(N) Na2S2O3 solution = 63.5 g of copper
1 mL of 1(N) Na2S2O3 solution = 0.0635 g of copper
Y mL of Z(N) Na2S2O3 solution = (0.0635 x Y x Z) g of copper
Y = Volume of Na2S2O3 solution required for the titration of the given copper solution (Ref.-
Table 2)
Z = Strength of Na2S2O3 solution
20 mL solution contains (0.0635 x Y x Z) g of copper
1000 mL solution contains [(0.0635 x Y x Z x 1000) / 20] g of copper
= P g (say) of copper
Conclusion: The amount of copper in the given solution is P g/L.
Precautions:
1. Na2S2O3 solution is always taken in the burette in iodometric titrations.
2. Sufficient amount of KI solution is to be added.
3. The indicator, starch, should be added just before the end point.
4. NH4SCN solution should be added near the end point to displace the adsorbed iodine and
to get a sharp end point.