Testing and Adjusting: Visual Checks

Download as pdf or txt
Download as pdf or txt
You are on page 1of 10

773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(SE...

Page 1 of 10

Shutdown SIS

Previous Screen

! " #$%## &' (


)*+
* *, - $.%*

!" #$ % $&& ' "() * $&+,++,+- % . $+ ,+&, &&+

Testing And Adjusting

Introduction
NOTE: For Specifications with illustrations, make reference to the SPECIFICATIONS FOR 772B
TRACTOR & 773B TRUCK HYDRAULIC SYSTEM, Form No. SENR7871. If the Specifications in
Form SENR7871 are not the same as in the Systems Operation and the Testing and Adjusting, look at
the printing date on the back cover of each book. Use the Specifications given in the book with the latest
date.

Hydraulic System
The 5S5123 Hydraulic Testing Group is used to make the pressure test of the hydraulic system. Before
making any tests, visually inspect the complete hydraulic system by looking for leakage of oil and for
parts that are damaged. For some of the tests a timer and a measuring rule (either for inches or for
millimeters) are usable tools.

When testing and adjusting the hydraulic system, move the machine to
a smooth horizontal location. Move away from working machines and
personnel. There must be only one operator. Keep all other personnel
away from the machine or where the operator can see them.

Visual Checks
A visual inspection of the hydraulic system and its components is the first step when making a diagnosis
of a problem. Stop the engine and when the oil is cool so any pressure in the tank will be at a minimum,
make the following inspections:

1. Measure the oil level. Slowly turn the filler cap until it is loose to let the tank pressure lower before
removing the filler cap. Look for air in the oil in the tank.

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010
773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(SE... Page 2 of 10

2. Check all oil lines and connections for damage or leaks.

Performance Test List


Performance tests of the hydraulic system can be used for a diagnosis of poor performance and to find
the source of oil leakage inside the hydraulic system.

Problem: Pump makes noise, the cylinder rods do not move smoothly and there are air
bubbles in the oil.

PROBABLE CAUSE:

1. The viscosity of the oil is wrong.


2. The relief valve opens at low oil pressure.
3. Loose connection of the oil line on the inlet side of the pump.
4. The pump has too much wear.

Problem: The temperature of the oil is too hot.

PROBABLE CAUSE:

1. The viscosity of the oil is wrong.


2. The relief valve opens at low oil pressure.
3. The pump has too much wear.
4. There is a restriction in an oil passage.
5. The load of the system is too high.

Problem: The output of the pump is low.

PROBABLE CAUSE:

1. Low level of the oil in the tank.


2. The viscosity of the oil is wrong.
3. The pump has too much wear.

Problem: The pressure of the oil is low.

PROBABLE CAUSE:

1. The relief valve opens at an oil pressure that is lower than the pressure in the
SPECIFICATIONS.
2. The pump has too much wear.
3. The failure of an O-ring seal in the system.

Checking Pump Efficiency


For any pump test, the pump flow, measured in U.S. gpm (liter/min) at 100 psi (690 kPa) will be larger
than the pump flow at 1000 psi (6900 kPa) at the same rpm.

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010
773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(SE... Page 3 of 10

The difference between the pump flow of two operating pressures is the flow loss.

Method of finding flow loss

Flow loss when expressed as a percent of pump flow is used as a measure of pump performance.

Example of finding percent of flow loss

If the percent of flow loss is more than 10% for test on the machine or 15% for test on the bench, pump
performance is not good enough.

*
Numbers in examples are for illustration and are not values for any specific pump or pump condition.
See SPECIFICATIONS FOR 772B TRACTOR & 773B TRUCK HYDRAULIC SYSTEM, Form No.
SENR7871, for pump flow of a new pump at 100 psi and 1000 psi.

Test On The Machine

Install a Flow Meter. Run the engine at 2000 rpm. Measure the pump flow at 100 psi (690 kPa) and at
1000 psi (6900 kPa). Use these values in Formula I.

Formula I

Test On The Bench

If the test bench can be run at 1000 psi and at full pump rpm, find the percent of flow loss using Formula
I.

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010
773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(SE... Page 4 of 10

If the test bench can not be run at 1000 psi at full pump rpm, run the pump shaft at 1000 rpm. Measure
the pump flow at 100 psi (690 kPa) and at 1000 psi (6900 kPa). Use these values in the top part of
Formula II. For the bottom part of the formula, run the pump shaft at 2000 rpm. Measure the pump flow
at 100 psi.

Formula II:

Cylinder Performance (Truck)


Lift Time for Hoist Cylinders

Start the engine and run it at high idle speed. Move the control lever to the RAISE position. Hold the
lever in RAISE position for 5 seconds after the body has lifted to dump position, then lower the body.
Do this lift and lower cycle many times to get the temperature of the hydraulic oil to more than 100 F
(38 C).

Lower the body to the frame and start the test. With the engine running at high idle speed, use the timer
to measure the time for the body to lift from the frame to dump position.

BODY IN DUMP POSITION

The time for the hoist cylinders to get fully extended and lift the body to dump position is approximately
11.5 seconds. Float down from the dump position is approximately 11 seconds.

Cylinder Drift

Start the engine and lift and lower the body many times to get an increase in the temperature of the
hydraulic oil.

The temperature of the hydraulic oil must not be less than 100F (38C). Make a record of the
temperature of the hydraulic oil.

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010
773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(SE... Page 5 of 10

With the body empty and the engine running, move the body control lever to the RAISE position. When
the body has lifted enough for the first stage of the hoist cylinders to be extended 12 in. (305 mm), move
the control lever to the HOLD position. Measure the distance the head end of the hoist cylinder has
lifted. Measure the distance again in 5 minutes. The difference between the two measurements is the
drift. Make a comparison of the record of the oil temperature and the drift measurement with the chart
for the HOIST CYLINDER DRIFT IN FIVE MINUTES.

Too much hoist cylinder drift is caused by:

1. Leaks in the lines and connections between the hydraulic tank and the hoist cylinders.
2. Worn control valve spool.
3. Worn seals in the hoist cylinders.

Relief Valve
The relief valve is part of the control valve. The control valve is below the level of the oil in the
hydraulic tank. When an adjustment is needed for the relief valve, hydraulic oil must be drained from
the tank.

Relief Valve Test (Truck)

Lower the body and stop the engine. After the engine stops move the control lever to RAISE and
LOWER positions, then put the lever in the FLOAT position.

LOCATION FOR RELIEF VALVE TEST


1. Hoist cylinder (left). 2. Plug in valve (oil line connection).

Remove plug (2) in the valve (oil line connection) on the rod end of hoist cylinder (1). Some oil will run
out when the plug is removed before the 5P3501 Adapter Assembly with the 5S4648 Hose Assembly,

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010
773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(SE... Page 6 of 10

the 1S8937 Valve and the 7S8714 Pressure Gauge are installed in the plug opening.

Start the engine and lift and lower the body many times to get the temperature of the hydraulic oil to
more than 100 F (38 C).

Run the engine at high idle speed and move the control lever to the RAISE position. After the body has
been lifted to dump position, look at the gauge and move the control lever and hold it in the RAISE
position. The high indication on the gauge is the pressure setting of the relief valve. The correct setting
for the relief valve is 2350 + 50 or - 0 psi (16 200 + 345 or - 0 kPa).

NOTE: Do not keep the control lever in RAISE position, at the relief valve pressure setting, for more
than 5 seconds.

Relief Valve Test (Tractor)

Move the control lever to the FLOAT position until the hydraulic component, on the unit pulled by the
tractor, stops its movements. Stop the engine, move the control lever to each position and then put the
control lever in the FLOAT position.

Install the 7S8714 Pressure Gauge on one end of the 5S4648 Hose Assembly and the 5S4965 Pressure
Plate on the other end.

Disconnect one of the hoses from the hydraulic tank at the hose junction for the pulled unit and install
the pressure plate (hose and gauge). It is necessary to use longer bolts through the flange when the
pressure plate is between the hose flange and the junction.

Start the engine and move the control lever to each position again and again to get the temperature of the
hydraulic oil to more than 100 F (38 C).

Run the engine at high idle speed and move the control lever to the position that puts hydraulic oil
through the hose where the pressure gauge is installed. Hold the lever in this position and look at the
pressure gauge. The high indication on the gauge is the pressure setting of the relief valve. The correct
setting of the relief valve is 2350 + 50 or - 0 psi (16 200 + 345 or - 0 kPa).

NOTE: Do not keep the control lever in RAISE position, at the relief valve pressure setting, for more
than 5 seconds.

If the setting of the relief valve is not correct, make a record of the indication on the gauge and make an
adjustment for the relief valve.

Adjustment of Relief Valve

Start and run the engine and move the control lever to the FLOAT position for approximately 20
seconds. Stop the engine.

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010
773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(SE... Page 7 of 10

COVER ON FRONT OF HYDRAULIC TANK

Drain the oil from the hydraulic tank until the oil level is below the cover of the tank. Remove the cover.

Remove plug (1), the shims under the plug and shims (2) in the plug. Either remove shims for a decrease
or add shims for an increase in the pressure setting of the relief valve.

Pilot valve spring (4) and pilot valve (3) must be in position when plug (1) and the shims are installed on
the relief valve. The torque for plug (1) is 80 5 lb. ft. (110 7 Nm).

6J3400 RELIEF VALVE (Part of Control Valve)


1. Plug. 2. Shims. 3. Pilot valve. 4. Pilot valve spring. [NOTE: 2J2866 Shims are under the hex of plug (1)].

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010
773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(SE... Page 8 of 10

Fill Oil Tank Procedure


1. Put oil in hydraulic tank until the oil can be seen in the gauge.

2. Start and run the engine at low idle rpm. With the engine running, add oil to the tank to keep the level
of the oil in the gauge.

3. When no more oil is needed to keep oil in the gauge, raise the body until the first stage cylinders are
half extended. Lower the body and add oil if needed.

4. Raise the body until the first stage cylinder is extended. Lower the body and add oil if needed.

5. Raise the body until the second stage cylinder is one-half extended. Lower the body and add oil if
needed. Raise the body until it is in full dump position. Lower the body and add oil if needed.

NOTE: If the unit pulled by the tractor has no hoist cylinders, hold the control lever in a position until
the hydraulic component is completely activated, then move the control lever to the HOLD position.
Add oil to the hydraulic tank if necessary. Hold the control lever in the other position, then to the HOLD
position and add oil if necessary.

6. Raise the body to full dump and lower it three times. Put on the brakes and release them three times.
Add oil needed to see the oil in the gauge.

Adjustment For Control LInkage


The hoist control linkage must be correctly adjusted when the machine is equipped with a transmission
neutralizer.

The transmission on this machine will neutralize when the transmission


shift lever is in REVERSE and the hydraulic control lever is in either
RAISE or LOWER position. The neutralizer will not stop the vehicle
from moving. Use the brakes to stop the vehicle.

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010
773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(SE... Page 9 of 10

CONTROL LEVER
1. Control lever. 2. 11.06 in. (281 mm) dimension (lever in FLOAT position, to doorsill).

If the truck has a transmission neutralizer and the transmission does not go from REVERSE to
NEUTRAL when control lever (1) is moved to either the RAISE or LOWER position, a linkage
adjustment may be necessary. An electric failure in the neutralizer switch or wires could also be the
cause.

The control lever (1) must be 11.06 in. (281 mm) from the doorsill of the cab when the lever is in the
FLOAT position. If the measurement for dimension (2) is not correct, the control linkage needs an
adjustment.

Loosen the locknut on rod (3) that is against fitting (5) and disconnect the fitting from the lever. If the
measurement for dimension (2) is too much, turn fitting (5) in the direction to make rod (3) longer.
Make the length of rod (3) shorter if measurement (2) is not enough.

CONTROL LINKAGE RODS


3. Rod from the shaft for the control lever in the cab. 4. Rod to the lever on the hydraulic control in the hydraulic oil tank. 5.
Fitting on end of rod.

The length for rod (3) is approximately 69.12 in. (1603.3 mm). The length of rod (4) is 50.88 in. (1292.4
mm).

It may be necessary to adjust the location of the neutralizer switch if the linkage dimensions are correct.
Remove the cover from the back of the operator's cab and then remove the four bolts which hold the
switch cover (box) to the inside wall of the cab. Remove the cover (box) from over the switch in the cab.

Move control lever (1) to the FLOAT position. The lower roller on yoke (9) must be near but not against
the short lever (not shown in the illustration) between the two rollers on the yoke.

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010
773B Off-Highway Truck 63W04200-UP (MACHINE) POWERED BY 3412 Engine(... Page 10 of 10

NEUTRALIZER SWITCH
6. Bolt (hidden). 7. Bracket. 8. Switch and plate. 9. Yoke.

If it is necessary to change the position of the yoke, move the control lever to the FLOAT position.
Loosen bolt (6) and then move switch and plate (8) until the lower roller on yoke (9) is near but not
against the short lever. Tighten the bolt.

If the position of yoke (9) can not be correctly adjusted by moving switch and plate (8) on bracket (7), it
will be necessary to make either one of the next two adjustments.

One of the adjustments is to make the length of rod (3) either longer or shorter until the lower roller on
yoke (9) is very near the short lever when control lever (1) is in FLOAT position.

NOTE: When rod (3) is made longer, be sure control lever (1) can be easily moved to the LOWER
position.

The second adjustment is for the location of yoke (9) on the switch. Put the control lever in the FLOAT
position and loosen the setscrew in the yoke. Move the yoke so that the lower roller, on the yoke, is near
but is not against the short lever between the rollers on the yoke. Tighten the setscrew in the yoke.

/! .00 %#.# / ( 1 4 % #0 . %0 7#8##%#.#


' 2 2 3 1
3 ) "4 5(56 2 21

https://jawav1:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 26/03/2010

You might also like