Chapter 6: 1D Elements and Connectors: Weld Adhesive Bolt Area Contact Replace Parts

Copyright 2009 Altair Engineering, Inc. Proprietary and Confidential. All rights reserved.
Chapter 6: 1D Elements
and Connectors Weld
Adhesive
Bolt
Area contact
Replace parts
1D Elements
1D Elements are simple connections between nodes.
Standard 1D Elements are
RBE2
Rigid link to
transfer motion
from the
independent
node to the
dependant
node(s)
1D Elements
RBE3
Rigid link to
distribute loads.
Will not induce
stiffenss
1D Elements
Beam/Bar
Non Rigid
Link that
has
properties
that include
a cross
section and
material
definitions.
Connectors: What are they & why use them?
Geometric entities that define connections between other entities

Used for welding, bolts, adhesives, etc.
Link geometry or FE entities
Can be realized into FE representations of welds, etc. for any supported solver
rigids, CWELDs, MAT100s, ACMs, etc.
Connectors allow for easy and rapid:

Creation of FE welds, bolts, adhesives, etc.
interactively or from:
XML file
MCF (master connectors file)
Spot welds only
Switching between different FE configurations of
welds, bolts, adhesives, etc.
Part swapping and reconnection
Replacement by names or IDs
Connectors: Types of Connectors
Spot Bolt
Connections at a point Connections at hole locations
Spot welds, rivets, etc. Bolts
Trim Mass
Non-physical mass
Simplification through replacement of parts
with mass only or add mass to existing part.
Connectors: Types of Connectors
Seam Area
Connections along a length Connection of areas
Seam welds Adhesives
Connects geometry only
Connectors: Terminology
Link Entities - The entities that are being connected

User can explicitly define link entities or specify a search tolerance
Can be components, elements, surfaces, nodes, or tags
Typically components are linked
Connector Location - Where the entities are linked

Nodes created at the node location
Points created at the point location
Lines created for the line
line may be split into multiple projection locations as specified by the offset,
spacing, and density values
Elements created at the element location (adhesives only)
Surface created at the surface location (adhesives only)
Connector Realization The creation of the finite element representation of that

connector
Rigids, springs, etc., or custom configurations such as ACMs, CWELDS, etc.
Connector State Whether an FE representation of a connector has been created

Unrealized - The initial status of the connector entity upon creation
Realized - The status only if creation of the FE weld representation at the
connector was successful
Failed The status if the creating the FE weld representation at the connector
was not successful
# of Layers number of FE weld layers to attempt to generate for the connector

2T, 3T, etc.
2T Weld 3T Weld
Connect When: Specifies when the link entity information is added to the
connector
Now - Allows you to add link entity information now. For this option, you must
select the connect what entities and num layers to successfully create a
connector.
At FE Realize - The link entities to the connector are determined while realizing
the connector. The link entities are determined by the projections and proximity
from the connector location.
Re-Connect Rule Defines method for connector re-attachment during part

swapping/replacement
None - If a link entity is deleted, the link entity is removed from the connector
By ID - If a link entity is deleted, the connector retains the ID of the link entity, and
will to a new entity with that ID upon realization
By Name Same as the by id rule except that the entity name is retained
Connectors: Tools
File >> Import >> Connectors Import Master Weld Files to automatically
create connectors
Connectors module
1D page >> connectors
Connector Browser
Hierarchal browser that provides information
and the ability to edit connectors
Connectors: Tools
Connectors Module
Spot
Bolt create, edit, and realize
Seam that style of connectors
Area
Apply Mass adds a mass value to entities
Used to represent mass of parts that are not present in the model
FE Absorb Create new connectors from existing elements of recognizable FE
representations of welds, bolts, adhesives, etc.
Add Links Add link entities to existing connectors
Unrealize Delete FE representations of welds / bolts / adhesives associated
with existing connectors
Compare Checks the MCF against displayed model file
Quality Check for duplicate connectors, combine connectors, check quality of
realized elements
Connectors: Tools
Connector Browser Hierarchal browser that

provides information and the ability to edit
connectors
Shows;
Type of Connector
Link Information
State of connector
Editable
Edit link entities, export mwf files, etc
Found in Tab Browser Area

Connectors Module: Visualization options
Visualization options
Use this tab to control how
connectors are displayed
Color connectors by state,

layers, or component
Visibility by state or layers
(can turn the display on or off)
Control size of connector
display

Chapter 6: 1D Elements and Connectors: Weld Adhesive Bolt Area Contact Replace Parts

Uploaded by

Copyright:

Available Formats

Chapter 6: 1D Elements and Connectors: Weld Adhesive Bolt Area Contact Replace Parts

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 6: 1D Elements and Connectors: Weld Adhesive Bolt Area Contact Replace Parts

Uploaded by

Copyright:

Available Formats

Copyright 2009 Altair Engineering, Inc. Proprietary and Confidential. All rights reserved.

1D Elements are simple connections between nodes.

Standard 1D Elements are

1D Elements are simple connections between nodes.

Standard 1D Elements are

1D Elements are simple connections between nodes.

Standard 1D Elements are

Connectors: What are they & why use them?

Geometric entities that define connections between other entities

Connectors allow for easy and rapid:

Connectors: Types of Connectors

Connectors: Types of Connectors

Link Entities - The entities that are being connected

Connector Location - Where the entities are linked

Connector Realization The creation of the finite element representation of that

Connector State Whether an FE representation of a connector has been created

# of Layers number of FE weld layers to attempt to generate for the connector

Re-Connect Rule Defines method for connector re-attachment during part

Connector Browser Hierarchal browser that

Found in Tab Browser Area

Connectors Module: Visualization options

Color connectors by state,

You might also like