Scribd Logo
Upload

Welcome to Scribd!

  • 92 views

    Dynamic CE Configuration

    Uploaded by

    nitin_vf
    This document describes how to configure Dynamic CE Resource Management on a Huawei RAN network. It involves activating the license, verifying activation by checking counters, and deactivating by disabling the license. The feature improves efficiency by adjusting CE allocation based on GBR and actual rates, and ensures fairness during preemption by properly allocating CEs.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Dynamic CE Configuration

    Uploaded by

    nitin_vf
    92 views1 page
    This document describes how to configure Dynamic CE Resource Management on a Huawei RAN network. It involves activating the license, verifying activation by checking counters, and deactivating by disabling the license. The feature improves efficiency by adjusting CE allocation based on GBR and actual rates, and ensures fairness during preemption by properly allocating CEs.

    Original Description:

    Dynamic CE Configuration

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document describes how to configure Dynamic CE Resource Management on a Huawei RAN network. It involves activating the license, verifying activation by checking counters, and deactivating by disabling the license. The feature improves efficiency by adjusting CE allocation based on GBR and actual rates, and ensures fairness during preemption by properly allocating CEs.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    92 views1 page

    Dynamic CE Configuration

    Uploaded by

    nitin_vf
    This document describes how to configure Dynamic CE Resource Management on a Huawei RAN network. It involves activating the license, verifying activation by checking counters, and deactivating by disabling the license. The feature improves efficiency by adjusting CE allocation based on GBR and actual rates, and ensures fairness during preemption by properly allocating CEs.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Configuring Dynamic CE Resource Management Page 1 of 1

    Configuring Dynamic CE Resource Management


    This section describes how to activate, verify, and deactivate the optional feature WRFD-010638 Dynamic CE Resource Management.

    Prerequisites

    The network is ready. For the dependency of this feature on NEs, see the RAN Optional Feature Description.
    The license has been activated.

    Context

    To improve the efficiency of CE resources, Huawei RAN introduces the dynamic CE resource management feature. Based on the GBR and actual rate, this feature enables the fast
    adjustment of CE allocation. When CE resources are preempted, this feature enables the proper allocation of CE resources to ensure the preemption fairness.

    Procedure

    Activation Procedure

    1. Switch on the license item of this feature through the M2000.

    NOTE:
    It is recommended that this feature not be activated when HSUPA DCCC is enabled.
    If this feature and HSUPA DCCC are activated at the same time, HSUPA DCCC becomes ineffective automatically. Similarly, after this feature is
    deactivated, HSUPA DCCC becomes effective automatically.

    Verification Procedure

    1. Run the NodeB MML command DSP LICENSE to check whether this feature is activated.
    2. Check the value of CE counters at the NodeB. The counter values show that when there are many HSUPA users, fewer CEs are assigned after this feature
    is activated.

    Deactivation Procedure

    1. Run the BSC6900 MML command DEA UCELLHSUPA to disable HSUPA for the cell, thus ensuring no HSUPA service is proceeding under the
    NodeB. For example,
    DEA UCELLHSUPA: CellId=80;

    2. Switch off the license item of this feature through the M2000.
    3. Run the BSC6900 MML command ACT UCELLHSUPA to activate HSUPA again for the cell.
    For example,
    ACT UCELLHSUPA: CellId=80;

    Parent topic: Configuring UMTS Features

    You might also like