Document ID: 1469808 Page 1 of 1

2008 Chevrolet Aveo | Aveo, Wave, G3, Barina (VIN S/T) Service Manual | Safety and Security | Remote Functions |
Component Locator | Document ID: 1469808

Vehicle Theft Deterrent System Components

(1) Theft Deterrent Control Module

(2) Theft Deterrent Control Module (removed)
(3) Hood Ajar Switch

2010 General Motors Corporation. All rights reserved.

http://localhost:9001/si/showDoc.do?docSyskey=1469808&from=sm 7/6/2010
Document ID: 1469805 Page 1 of 1

2008 Chevrolet Aveo | Aveo, Wave, G3, Barina (VIN S/T) Service Manual | Safety and Security | Remote Functions |
Component Locator | Document ID: 1469805

Content Theft Components

(1) Door Latch Left - Right Similar

(2) Theft Deterrent Alarm
(3) Lock Cylinder Switch - Rear Compartment Lid

2010 General Motors Corporation. All rights reserved.

http://localhost:9001/si/showDoc.do?docSyskey=1469805&from=sm 7/6/2010
Document ID: 1792710 Page 1 of 1

2008 Chevrolet Aveo | Aveo, Wave, G3, Barina (VIN S/T) Service Manual | Safety and Security | Remote Functions |
Component Locator | Document ID: 1792710

Remote Function Component Views (Hatchback)

Vehicle Theft Deterrent System Components

(1) Theft Deterrent Control Module

(2) Theft Deterrent Control Module (removed)
(3) Hood Ajar Switch

2010 General Motors Corporation. All rights reserved.

http://localhost:9001/si/showDoc.do?docSyskey=1792710&pubCellSyskey=156642&pubO... 7/6/2010
Document ID: 1739100 Page 1 of 2

2008 Chevrolet Aveo | Aveo, Wave, G3, Barina (VIN S/T) Service Manual | Safety and Security | Remote Functions |
Component Locator | Document ID: 1739100

Remote Function Connector End Views (Notchback)

Remote Control Door Lock Receiver (RCDLR)/Theft Deterrent Control
Module

KET MG 611336
Connector Part Information
26-Way F PCB Connector (WH)
Pin Wire Circuit Function
1 YE -- Arm Alarm Signal
2 BK -- Ground
3 -- -- Not Used
4 PU -- Rear Compartment Lid Switch Signal
5 OG/BK -- Rear Compartment Lid Ajar Switch Signal
6 -- -- Not Used
7 PK/D-BU -- Hood Ajar Switch Signal
8 WH -- Door Ajar Signal
9 L-BU -- Door Lock Control
10 GY/D-GN -- Driver Door Lock Relay Lock Control
11 YE -- Driver Door Lock Relay Unlock Control
12 PU -- Door Latch Switch Signal
13 D-BU -- Right Turn Signal Lamps Supply Voltage
14 BN -- Rear Compartment Lid Switch Signal
15 PK -- Ignition 1 Voltage
16 -- -- Not Used
17 BK/WH -- Serial Data
18 L-GN -- Key In Ignition Switch Signal
19 YE -- Security Indicator Control
20 PU -- Door Latch Switch Signal
2010 General Motors Corporation. All rights reserved.

http://localhost:9001/si/showDoc.do?docSyskey=1739100&pubCellSyskey=156643&pubO... 7/6/2010
Document ID: 1739100 Page 2 of 2

21-24 -- -- Not Used

25 RD/WH -- Battery Positive Voltage
26 L-BU -- Left Turn Signal Lamps Supply Voltage

http://localhost:9001/si/showDoc.do?docSyskey=1739100&pubCellSyskey=156643&pubO... 7/6/2010
Document ID: 1792714 Page 1 of 4

2008 Chevrolet Aveo | Aveo, Wave, G3, Barina (VIN S/T) Service Manual | Safety and Security | Remote Functions |
Component Locator | Document ID: 1792714

Remote Function Connector End Views (Hatchback)

Table 1: Hood Ajar Switch
Table 2: Lock Cylinder Switch - Rear Compartment
Table 3: Remote Control Door Lock Receiver (RCDLR)
Table 4: Theft Deterrent Alarm
Table 5: Theft Deterrent Control Module
Hood Ajar Switch

KET MG 610392
Connector Part Information
2-Way F Series Sealed (WH)
Pin Wire Circuit Function
1 BN/BK 109 Hood Ajar Switch Signal
2 OG 1440 Battery Positive Voltage
Lock Cylinder Switch - Rear Compartment

KET MG 610070
2010 General Motors Corporation. All rights reserved.

http://localhost:9001/si/showDoc.do?docSyskey=1792714&pubCellSyskey=156643&pubO... 7/6/2010
Document ID: 1792714 Page 2 of 4

Connector Part Information 2-Way F 090 (2.3 mm) Series (WH)

Pin Wire Circuit Function
1 D-BU 737 Rear Compartment Lid Ajar Switch Signal
2 BK 850 Ground
Remote Control Door Lock Receiver (RCDLR)

KET MG 611336
Connector Part Information
26-Way F PCB Connector (WH)
Pin Wire Circuit Function
1 D-GN/WH 261 Arm Alarm Signal
2 BK 650 Ground
3 -- -- Not Used
4 D-BU 49 Tamper Switch Signal (4-Door)
5 OG/BK 737 Rear Compartment Lid Ajar Switch Signal
6 -- -- Not Used
7 BN/BK 109 Hood Ajar Switch Signal
8 D-GN/WH 157 Courtesy Lamp Control
9 GY 195 Door Lock Control
10 GY/D-GN 355 Low Speed Cooling Fan Relay Control
11 YE/D-GN 356 Driver Door Lock Relay Unlock Control
12 D-BU 49 Tamper Switch Signal
13 D-BU 15 Right Turn Signal Lamps Supply Voltage
14 -- -- Not Used
15 PK 239 Ignition 1 Voltage
16 -- -- Not Used
17 BK/WH 2051 Serial Data
18 L-GN 80 Key In Ignition Switch Signal
19 YE 749 Security Indicator Control
20 D-BU 49 Tamper Switch Signal

http://localhost:9001/si/showDoc.do?docSyskey=1792714&pubCellSyskey=156643&pubO... 7/6/2010
Document ID: 1792714 Page 3 of 4

21-24 -- -- Not Used

25 OG 1340 Battery Positive Voltage
26 L-BU 14 Left Turn Signal Lamps Supply Voltage
Theft Deterrent Alarm

KUM PB 625-02027
Connector Part Information
2-Way F NMWP 04F-B Assembly (BK)
Pin Wire Circuit Function
1 D-GN/WH 261 Arm Alarm Signal
2 BN 641 Ignition 3 Voltage
Theft Deterrent Control Module

SD 35508-0700
Connector Part Information
7-Way Connector F (WH)
Pin Wire Circuit Function
1 PK 239 Ignition 1 Voltage
2 OG 240 Battery Positive Voltage
3 -- -- Not Used

http://localhost:9001/si/showDoc.do?docSyskey=1792714&pubCellSyskey=156643&pubO... 7/6/2010
Document ID: 1792714 Page 4 of 4

4 BK 450 Ground
5 D-BU/WH 1800 Battery Positive Voltage
6 BK/WH 2051 Serial Data
7 YE 749 Security Indicator Control

http://localhost:9001/si/showDoc.do?docSyskey=1792714&pubCellSyskey=156643&pubO... 7/6/2010
Document ID: 1727795 Page 1 of 2

2008 Chevrolet Aveo | Aveo, Wave, G3, Barina (VIN S/T) Service Manual | Safety and Security | Remote Functions |
Repair Instructions | Document ID: 1727795

Remote Control Door Lock Receiver Replacement

(Hatchback)
Removal Procedure

Caution: Refer to Battery Disconnect Caution in the Preface section.

Important: Remote keyless transmitters must be programmed when remote control

module/receiver is replaced.

1. Disconnect the negative battery cable.

2. Remove the floor console. Refer to Front Floor Console Replacement .
3. Disconnect the control module/receiver electrical connector.
4. Slide the control module/receiver away from its mounting bracket.

Installation Procedure

2010 General Motors Corporation. All rights reserved.

http://localhost:9001/si/showDoc.do?docSyskey=1727795&pubCellSyskey=52196&pubObj... 7/6/2010
Document ID: 1727795 Page 2 of 2

1. Install the control module/receiver on its mounting bracket.

2. Connect the control module/receiver electrical connector.
3. Install the floor console. Refer to Front Floor Console Replacement .
4. Connect the negative battery cable.
5. Complete remote keyless transmitter programmming. Refer to Transmitter Programming

http://localhost:9001/si/showDoc.do?docSyskey=1727795&pubCellSyskey=52196&pubObj... 7/6/2010
Document ID: 1860073 Page 1 of 2

2008 Chevrolet Aveo | Aveo, Wave, G3, Barina (VIN S/T) Service Manual | Safety and Security | Remote Functions |
Repair Instructions | Document ID: 1860073

Remote Control Door Lock Receiver Replacement

(Notchback)
Removal Procedure

Caution: Refer to Battery Disconnect Caution in the Preface section.

Important: Remote keyless transmitters must be programmed when remote control

module/receiver is replaced.

1. Disconnect the negative battery cable.

2. Separate the hood release cable from the hood latch release handle.
3. Carefully pull the instrument panel under cover until the mounting clips are released and the
instrument panel under the cover.
4. Remove the bolts from the driver's side knee bolster.
5. Disconnect the control module/receiver electrical connector.
6. Slide the control module/receiver away from its mounting bracket.

Installation Procedure

2010 General Motors Corporation. All rights reserved.

http://localhost:9001/si/showDoc.do?docSyskey=1860073&pubCellSyskey=52196&pubObj... 7/6/2010
Document ID: 1860073 Page 2 of 2

1. Install the control module/receiver on its mounting bracket.

2. Connect the control module/receiver electrical connector.

Notice: Refer to Fastener Notice in the Preface section.

3. Install the knee bolster with bolts.

Tighten
Tighten the driver's side knee bolster mounting bolts to 10 N m (89 lb in).

4. Install the instrument panel under cover.

5. Connect the hood release cable to the hood latch release handle.
6. Install the screws.
7. Connect the negative battery cable.
8. Complete remote keyless transmitter programmming. Refer to Transmitter Programming

http://localhost:9001/si/showDoc.do?docSyskey=1860073&pubCellSyskey=52196&pubObj... 7/6/2010
Document ID: 1885067 Page 1 of 1

2008 Chevrolet Aveo | Aveo, Wave, G3, Barina (VIN S/T) Service Manual | Safety and Security | Remote Functions |
Repair Instructions | Document ID: 1885067

Transmitter Programming
Remote Keyless Entry Transmitter Programming

The remote keyless entry system allows for the use of as many as five (5) transmitters for each
vehicle. Replacement remote keyless entry system transmitters must first be programmed to
specific vehicle using the Secan tool. This process is completed using serial data communication
between the scan tool and the remote keyless entry control unit and is the only method available
for programming transmitters.

All transmitters for a specific vehicle must be programmed at same time. Once the programming
function of the remote keyless entry system is activated, any transmitter (existing or new) that is
not programmed (or reprogrammed) during the programming procedure will no longer operate the
remote keyless entry system of that vehicle. Ensure that the doors, hood and trunk/tailgate hatch
are closed prior to starting the programming procedure.

Ensure that transmitters from other vehicles in the immediate area are not activated during
programming procedure. Turn the ignition to ON before installing in the scan tool. Failure to
connect in this procedure may cause communication errors and the programming procedure will
not complete.

Any keys that are not programmed at this time will no longer function.

1. Turn ON the ignition, with the engine OFF.

2. Install the scan tool.
3. Select PROGRAMMING KEY FOBS from the BODY menu.
4. Follow the scan tool instruction with each key until all keys are programmed.
5. Turn the ignition to the LOCK position, disconnect the Tech 2 and test all the keys.

2010 General Motors Corporation. All rights reserved.

http://localhost:9001/si/showDoc.do?docSyskey=1885067&pubCellSyskey=52171&pubObj... 7/6/2010