Scribd
Upload
57 views3 pages

Culvert II

This document contains information about the materials, cross-sectional properties, boundary conditions, and load cases for 3 beam sets that are part of a structural analysis. The beam sets have cross-sectional dimensions of b/d=100/40, b/d=100/20, and b/d=60/30 and are made of a concrete labeled Beton MB 30. The linear support conditions and 10 load cases are also defined, including self-weight, earth pressure, traffic load, and various combinations of these loads. Reinforcement limits based on EC 2 standards are also specified.

Uploaded by

ilijarsk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
57 views3 pages

Culvert II

This document contains information about the materials, cross-sectional properties, boundary conditions, and load cases for 3 beam sets that are part of a structural analysis. The beam sets have cross-sectional dimensions of b/d=100/40, b/d=100/20, and b/d=60/30 and are made of a concrete labeled Beton MB 30. The linear support conditions and 10 load cases are also defined, including self-weight, earth pressure, traffic load, and various combinations of these loads. Reinforcement limits based on EC 2 standards are also specified.

Uploaded by

ilijarsk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 3

b/d=60/30

b/d=100/40
b/d=100/40
[1]
b/d=100/20

Table of materials
No Material name E[kN/m2] [kN/m3] t[1/C] Em[kN/m2] m
1 Beton MB 30 3.150e+7 0.20 25.00 1.000e-5 3.150e+7 0.20

Beam sets

Set: 1 Section: b/d=100/40, Approx. eccentricity


Mat. A1 A2 A3 I1 I2 I3
2 1 - Beton MB 30 4.000e-1 3.333e-1 3.333e-1 1.597e-2 3.333e-2 5.333e-3
40

T 3

100

[cm]

Set: 2 Section: b/d=100/20, Approx. eccentricity


Mat. A1 A2 A3 I1 I2 I3
2 1 - Beton MB 30 2.000e-1 1.667e-1 1.667e-1 2.331e-3 1.667e-2 6.667e-4
20

T 3

100

[cm]

Set: 3 Section: b/d=60/30, Approx. eccentricity


Mat. A1 A2 A3 I1 I2 I3
2 1 - Beton MB 30 1.800e-1 1.500e-1 1.500e-1 3.708e-3 5.400e-3 1.350e-3
30

T 3

60

[cm]

Linear support sets


Set K,R1 K,R2 K,R3 K,M1 Soil [m]
1 3.000e+3 1.000e+10 1.000

Tower - 3D Model Builder 7.0 Registered to Ludwig PfeifferHoch- Und Tiefbau GmbH Radimpex - www.radimpex.rs
Load cases list
LC Name
1 Selfweight (g)
2 Earth pressure
3 Traffic load
4 Comb.: 1.35xI+1.35xII+1.5xIII
5 Comb.: I+1.35xII+1.5xIII
6 Comb.: 1.35xI+II+1.5xIII
7 Comb.: I+II+1.5xIII
8 Comb.: 1.35xI+1.35xII
9 Comb.: I+1.35xII
10 Comb.: 1.35xI+II
11 Comb.: I+II
Load 2: Earth pressure

5.00

p=1 8
.65~

.65~
p=1 8

5.00
Load 3: Traffic load

p=125.00
Governing load: Complete scheme
EC 2 (EN 1992-1-1:2004), C 20, Bst420

1.60
0.75
0.08 0.08

1.45
1.45
Beam reinforcement: max Aa2/Aa1= 0.75 / 1.60 cm

You might also like