Scribd
Upload
73 views3 pages

Isometric: Table of Materials

This document summarizes the analysis of two reinforced concrete beams (b/d ratios of 100/40 and 100/20) that are part of a tower structure. It includes the material properties, beam geometry, support conditions, six load cases, and results of the linear support analysis. The critical load case produced a maximum support reaction of 23.62 kN/m and minimum of 23.47 kN/m. Beam reinforcement ratios were also reported.

Uploaded by

ilijarsk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
73 views3 pages

Isometric: Table of Materials

This document summarizes the analysis of two reinforced concrete beams (b/d ratios of 100/40 and 100/20) that are part of a tower structure. It includes the material properties, beam geometry, support conditions, six load cases, and results of the linear support analysis. The critical load case produced a maximum support reaction of 23.62 kN/m and minimum of 23.47 kN/m. Beam reinforcement ratios were also reported.

Uploaded by

ilijarsk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 3

b/d=100/40 Isometric

b/d=100/40
[1]
b/d=100/20

Table of materials
No Material name E[kN/m2] [kN/m3] t[1/C] Em[kN/m2] m
1 Beton MB 30 3.150e+7 0.20 25.00 1.000e-5 3.150e+7 0.20

Beam sets

Set: 1 Section: b/d=100/40, Approx. eccentricity


Mat. A1 A2 A3 I1 I2 I3
2 1 - Beton MB 30 4.000e-1 3.333e-1 3.333e-1 1.597e-2 3.333e-2 5.333e-3
40

T 3

100

[cm]

Set: 2 Section: b/d=100/20, Approx. eccentricity


Mat. A1 A2 A3 I1 I2 I3
2 1 - Beton MB 30 2.000e-1 1.667e-1 1.667e-1 2.331e-3 1.667e-2 6.667e-4
20

T 3

100

[cm]

Linear support sets


Set K,R1 K,R2 K,R3 K,M1 Soil [m]
1 3.000e+3 1.000e+10 1.000

Tower - 3D Model Builder 7.0 Registered to Ludwig PfeifferHoch- Und Tiefbau GmbH Radimpex - www.radimpex.rs
Load cases list
LC Name
1 Selfweight (g)
2 Earth pressure
3 Comb.: 1.35xI+1.35xII
4 Comb.: I+1.35xII
5 Comb.: 1.35xI+II
6 Comb.: I+II
Load 2: Earth pressure

5.00

p=1 8
.65~

.65~
p=1 8

5.00
Load 6: I+II

[1]

23.61
Linear Support Results: max r2= 23.62 / min r2= 23.47 kN/m
Governing load: Complete scheme
EC 2 (EN 1992-1-1:2004), C 20, Bst420

0.68 1.78 0.68


1.78

Beam reinforcement: max Aa2/Aa1= 0.68 / 1.78 cm

You might also like