Scribd
Upload
41 views1 page

Section Llechanized Welding With Filler Metal Additions: Guide For API Standard 1104, Twentieth Edition AWS API-M:2006

This document appears to be sections from an API standard guide for welding procedures. Section 12 discusses requirements for mechanized welding with filler metal additions, including procedure qualification, essential variables, operator qualification, inspection standards, and repair of defects. Section 13 covers similar requirements for automatic welding without filler metal additions. Appendix A provides alternative acceptance standards for girth welds, and Appendix B addresses in-service welding requirements and practices.

Uploaded by

Alessandro sergio de souza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
41 views1 page

Section Llechanized Welding With Filler Metal Additions: Guide For API Standard 1104, Twentieth Edition AWS API-M:2006

This document appears to be sections from an API standard guide for welding procedures. Section 12 discusses requirements for mechanized welding with filler metal additions, including procedure qualification, essential variables, operator qualification, inspection standards, and repair of defects. Section 13 covers similar requirements for automatic welding without filler metal additions. Appendix A provides alternative acceptance standards for girth welds, and Appendix B addresses in-service welding requirements and practices.

Uploaded by

Alessandro sergio de souza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 1

S'::Yjy Guide for API Standard 1104, Twentieth Edition AWS API-M:2006

Section 12- 12.1 Acceptable Processes ...........................................................................................12-1


llechanized 12.2 Procedure Qualification ......................................................................................12-1
Welding with 12.3 Record .................................................................................................................12-1
Filler Metal 12.4 Procedure Specification .......................................................................................12-1
Additions 12.5 Essential Variables ...............................................................................................12-2
12.6 Qualification of Welding Equipment and Operators .............................................12-2
12.7 Records of Qualified Operators ...........................................................................12-3
12.8 Inspection and Testing of Production Welds ........................................................12-3
12.9 Acceptance Standards for Nondestructive Testing ................................................12-3
12.10 Repair and Removal of Defects .........................................................................12-3
12.11 Radiographic Testing ..........................................................................................12-3

Section 13- 13.1 Acceptable Processes ...........................................................................................13-1


Automatic 13.2 Procedure Qualification .......................................................................................13-1
Welding without 13.3 Record .................................................................................................................13-1
RlIer-Metal 13.4 Procedure Specification .......................................................................................13-1
Additions 13.5 Essential Variables ...............................................................................................13-1
13.6 Qualification of Welding Equipment and Operators ............................................13-1
13.7 Records ofQualified Operators ............................................................................13-1
13.8 Quality Assurance ofProduction Welds ................................................................13-2
13.9 Acceptance Standards for Nondestructive Testing ................................................13-2
13.10 Repair and Removal ofDefects ...........................................................................13-2
13.11 Radiographic Procedure .....................................................................................13-2

Appndix A A.1 General ...................................................................................................................A-I


Afternative A.2 Additional Requirements for Stress Analysis ..........................................................A-I
Acceptance A.3 Welding Procedure ...............................................; ................................................A-I
Standards for A.4 Qualification of Welders .........................................................................................A-2
Girth Welds A.5 Inspection and Acceptable Limits ...........................................................................A-2
A.6 Record ....................................................................................................................A-2
A.7 Example .................................................................................................................A-2
A.8 Repairs ...................................................................................................................A-2
A.9 Nomenclature .........................................................................................................A-2

Appendix B n- B.I General ....................................................................................................................B-I


Service Welding B.2 Qualification of In-Service Welding Procedures .....................................................B-I
B.3 In-Service Welder Qualification ............................................................................... B-S
B.4 Suggested In-Service Welding Practices ............................................................... B-S
B.S Inspection and Testing of In-Service Welds ..............................................................B-6
B.6 Standards of Acceptability: Nondestructive Testing
(lncluding Visual) ..............................................................................................B-6
B.7 Repair and Removal of Defects ...............................................................................B-6

Exercise Questions ......................................................................................................EQ-l

VlI

You might also like