Re 500-SD PDF

HIT-RE 500-SD
Epoxy Adhesive
Anchor System
Code compliance with

Strength Design performance.
Hilti. Outperform. Outlast.
HIT-RE 500-SD Epoxy Adhesive Anchor
Code compliance
with Strength Design
performance.
HIT-RE 500-SD Epoxy
Adhesive Anchor System
The Hilti HIT-RE 500-SD Epoxy Adhesive Anchor is a revolutionary new system
designed to meet the most stringent standards of the latest building codes. This
high performing anchor system can be used in cracked or un-cracked concrete and
high seismic conditions for anchoring applications with a standard Hilti HAS Rod.
Additionally, HIT-RE 500-SD can be used in the same conditions with rebar for
dowelling and structural reinforcement.
Hilti HIT-RE 500-SD is compliant with all current building codes in the United States
and is versatile enough for virtually any application. .
Building Code Compliance
The industrys first adhesive anchor to be qualified for use under the 2003/2006
IBC, offering designers strength design solutions for anchors and rebar.
High seismic design category, cracked or un-cracked concrete, IBC 2003, IBC
2006 and 1997 UBC You are covered for virtually any application anywhere.
Reliability
Hilti HIT-RE 500-SD is also available with the HIT PROFI installation kits for a
simple and reliable installations on every project even the most challenging
applications.
Performance
Hilti raises the bar once again with industry-leading bond strength
performance.
The latest building codes require stringent testing of anchors intended for use
in cracked concrete Hilti HIT-RE 500-SD meets these requirements with
ease using a standard threaded rod no special elements required.
Technical Support and Training
PROFIS Anchor Design software performs strength design calculations right

on your computer and it is free to download.
Hilti is now offering a Certified Installer Program to help make installers
proficient and more efficient on the jobsite.
Over 1,000 Account Managers and 60 Field Engineers provide training and
technical support onsite or in the design office.
2 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I RE 500-SD Submittal Information 7/07
HIT-RE 500-SD Epoxy Adhesive Anchor System Technical Data

Product Epoxy Adhesive
First adhesive anchor to comply with the latest Base material temperature 41F to 120F (+5C to 49C)
Diameter range 3/8" to 1-1/4"
building code, offering designers a strength Listings/Approvals
design solution for anchors and rebar ICC-ES Pending
NSF/ANSI standard 61 Certification for potable water
Enables threaded rod and dowelling Package volume
Volume of HIT-RE 500-SD 11.1fl oz/330 ml foil pack is
applications in seismic design conditions 20.1 in3
Volume of HIT-RE 500-SD 16.9 fl oz/500 ml foil pack is
under the latest building codes 30.5 in3
Gel/Full Cure Time Table (Approximate)

Base Material
Temperature
Item No. Description
F C tgel tcure
241382 HIT-RE 500-SD (11.1 fl oz/330 ml) - 1 pack 41 5 2.5 hrs 72 hrs
Includes 1 mixer and 3/8" filler tube per package 50 10 2 hrs 48 hrs
3425973 HIT-RE 500-SD (11.1 fl oz/330 ml) MC - 25 packs 59 15 1.5 hrs 24 hrs
3428744 HIT-RE 500-SD (11.1 fl oz/330 ml) 68 20 30 min 12 hrs
Includes 1 MC and choice of MD 2000 or MD 2500 dispenser 86 30 20 min 8 hrs
104 40 12 min 4 hrs
241383 HIT-RE 500-SD (16.9 fl oz/500 ml) MC - 20 packs
Includes 1 mixer and 3/8" filler tube per package
Dispensers
Battery Powered
Item No. Description ED 3500 2.0 Ah Kit
3425363 ED 3500 2.0 Ah Kit
Includes dispenser, 2.0-Ah NiCd battery, C 7/24 standard charger and accessories in an impact-
resistant plastic tool box
273676 ED 3500 Dispenser
Includes dispenser only in cardboard box
340888 SFB 121 2.0-Ah NiCd Battery for ED 3500
378449 C 7/24 Standard Charger for ED 3500 Foil Pack Holder
3426080 HIT-RE 500-SD (16.9 fl oz/500 ml)
Includes 5 MC and ED 3500 Dispenser 2.0 Ah Kit
3433546 HIT-RE 500-SD (16.9 fl oz/500 ml)
Includes 2 MC and MD 2500 Dispenser
Manual MD 2500 Manual Dispenser

Item No. Description
338853 MD 2500 Manual Dispenser with Foil Pack Holder
For use with HIT 11.1 fl oz/330ml and 16.9oz/500ml foil pack
339477 Foil Pack Holder
Replacement for MD 2500 and ED 3500
Hole Cleaning/Injection Accessories

Imperial Metric
do Round Brush Injection Piston Air Nozzle do Round Brush Injection Piston Air Nozzle HIT-RB
(Round Brush)
HIT-SZ HIT-SZ
[inch] HIT-RB Item no. (IP) Item no. HIT-DL Item no. mm HIT-RB Item no. Item no. HIT-DL Item no.
(IP)
7/16 7/16" 273203 10 10 380917
1/2 1/2" 273204 1/2" 274019 1/2" 38237 12 8/12 336548 8/12 351989 8/12 371715
9/16 9/16" 273205 9/16" 274020 9/16" 38238 HIT-SZ (IP)
14 10/14 336549 10/14 351990 10/14 371716 (Injection Piston)
5/8 5/8" 273207 5/8" 274021 9/16" 38238 16 12/16 336550 12/16 351991 12/16 371717
11/16 11/16" 273209 11/16" 274022 11/16" 38239 18 14/18 336551 14/18 351992 14/18 371718
3/4 3/4" 273210 3/4" 274023 3/4" 38240 20 16/20 336552 16/20 351993 16/20 371719
7/8 7/8" 273211 7/8" 274024 7/8" 38241 22 18/22 370774 18/22 269618 16/20 371719
HIT-DL
1 1" 273212 1" 274025 1" 38242 24 24 380918 24 269619 16/20 3 71719 (Air Nozzle)
1-1/8 1-1/8" 273214 1-1/8" 274026 1" 38242 25 20/25 336553 20/25 351994 20/25 371720
1-1/4 1-1/4" 273216 1-1/4" 274027 1" 38242 28 28 380919 28 269620 20/25 371720
1-3/8 1-3/8" 273217 1-3/8" 274028 1-3/8" 38243 30 30 380920 30 269621 20/25 371720
1-1/2 1-1/2" 273218 1-1/2" 274029 1-3/8" 38243 32 25/32 336554 25/32 351995 25/32 371721
1-3/4 1-3/4" 273219 1-3/4" 274030 1-3/8" 38243 35 35 380921 35 269622 25/32 371721
37 37 382259 37 271499 25/32 371721
40 40 382260 40 269623 25/32 371721
42 42 382261 42 269624 25/32 371721
45 45 382262 45 269625 25/32 371721
47 47 382264 47 269626 25/32 371721
52 52 382265 52 271476 25/32 371721
55 55 382266 55 271477 25/32 371721
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I RE 500-SD Submittal Information 7/07 3
Adhesive Anchoring Systems

Guide Specifications which thoroughly blends component A 1. ISO 898 Class 5.8
and component B and allows injection
Master Format Section: 2. ASTM A 193, Grade B7 (high strength
directly into drilled hole. Only injection
carbon steel anchor);
03250 (Concrete accessories) tools and static mixing nozzles as
recommended by manufacturer shall be 3. AISI 304 or AISI 316 stainless steel,
Related Sections:
used. Manufacturers instructions shall meeting the requirements of ASTM F
03200 (Concrete Reinforcing- be followed. Injection adhesive shall be 593 (condition CW).
Reinforcing Accessories) formulated to include resin and hardener
Special order length HAS Rods may
05050 (Metal Fabrication) to provide optimal curing speed as well
vary from standard product.
05120 (Structural Steel; Masonry as high strength and stiffness. Typical
Accessories) curing time at 68F (20C) shall be Nuts and Washers of other grades and
approximately 12 hours. styles having specified proof load
Injectable adhesive shall be used for
stresses greater than the specified
installation of all reinforcing steel dowels Injection adhesive shall be
grade and style are also suitable. Nuts
or threaded anchor rods and inserts into HIT-RE 500-SD, as furnished by Hilti.
must have specified proof load stresses
new or existing concrete. Adhesive
Anchor Rods shall be furnished with equal to or greater than the minimum
shall be furnished in side-by-side refill
chamfered ends so that either end will tensile strength of the specified
packs which keep component A and
accept a nut and washer. Alternatively, threaded rod.
component B separate. Side-by-side
anchor rods shall be furnished with a 45
packs shall be designed to compress
degree chisel point on one end to allow
during use to minimize waste volume.
for easy insertion into the adhesive-filled
Side-by-side packs shall also be
hole. Anchor rods shall be manufactured
designed to accept static mixing nozzle
to meet the following requirements:
Material Specifications for HIT-RE 500-SD Cured Adhesive
Bond Strength ASTM C882-911

2 day cure 12.4 MPa 1800 psi
7 day cure 12.4 MPa 1800 psi
Compressive Strength ASTM D-695-961 82.7 MPa 12,000 psi
Compressive Modulus ASTM D-695-961 1493 MPa 0.22 x 106 psi
Tensile Strength 7 day ASTM D-638-97 43.5 MPa 6310 psi
Elongation at break ASTM D-638-97 2.0% 2.0%
Heat Deflection Temperature ASTM D-648-95 63C 146F
Absorption ASTM D-570-95 0.06% 0.06%
Linear Coefficient of Shrinkage on Cure ASTM D-2566-86 0.004 0.004
Electrical resistance DIN IEC 93 (12.93) 6.6 x 1013 /m 1.7 x 1012/in.
1 Minimum values obtained as a result of three cure temperatures (23, 40, 60F)

STRENGTH DESIGN D.5.2.8 The limiting concrete strength D.5.3.8 The critical spacing and
of adhesive anchors in tension shall be critical edge distance shall be calculated
Design strengths are determined in
calculated in accordance with D.5.2.1 to as follows:
accordance with ACI 318-05 Appendix D k,uncr
(ACI 318) and this report1. Design
D.5.2.7 where the value of kc to be used scr,Na = 20 . d . 3 . hef (D-14h)
in Eq. (D-7) shall be: 1,450
parameters are provided in Error!
Reference source not found. through kc,cr where analysis indicates cracking scr,Na
ccr,Na = (D-14i)
Error! Reference source not found. at service load levels in the 2
Strength reduction factors f as given in anchor vicinity (cracked concrete)
D.5.3.9 The basic strength of a single
ACI 318 D.4.4 shall be used for load
kc,uncr where analysis indicates no adhesive anchor in tension in cracked
combinations calculated in accordance
cracking at service load levels in concrete shall not exceed
with Section 1612.2 of the UBC or
the anchor vicinity (un-cracked NaO = kcr . . d . hef (D-14j)
Section 1605.2 of the 2000, 2003 or 2006
concrete)
IBC. Strength reduction factors f as given D.5.3.10 The modification factor for
in ACI 318 D.4.5 shall be used for load D.5.3.7 The nominal bond strength of
the influence of the failure surface of a
combinations calculated in accordance an adhesive anchor Na or group of
group of adhesive anchors is
with Section 1909.2 of the UBC. adhesive anchors Nag in tension shall
not exceed (D-14k)
This section provides amendments to
ACI 318-05 Appendix D (ACI 318) as
required for the strength design of
(a) for a single anchor
ANa . c p,Na . Na0
Na = (D-14a)
cg,Na = cg,NaO +
[( ) S

Scr,Na
0.5
. (1 cg,NaO) 1.0
]
Aa0 where
adhesive anchors. In conformance with
ACI 318-05, all equations are expressed (b) for a group of anchors (D-14l)
k,cr
in inch-pound units.
ANa . c
Nag =
(D-14b)
ed,Na . cg,Na . cec,Na . cp,Na . Na0
cg,Nao = n
[ ( n 1)
( ) ]

k,max,cr
1.5
. 1.0
D.4.1.2 In Eq. (D-1) and (D-2), Nn and Aa0 With n as the number of tension-loaded
Vn are the lowest design strengths adhesive anchors in a group.
determined from all appropriate failure where
k,max,uncr = kc,cr
hef . fc (D-14m)

modes. Nn is the lowest design strength Ana is the projected area of the failure p.d
in tension of an anchor or group of surface for the anchor or group of D.5.3.11 The modification factor for
anchors as determined from anchors that shall be approximated as eccentrically loaded adhesive anchor
consideration of Nsa, either Na or Nag and the base of the rectilinear geometrical groups is
either Ncb or Ncbg. Vn is the lowest design figure that results from projecting the 1 1.0
cec,Na = (D-14n)
strength in shear of an anchor or a group failure surface outward a distance from 2e'n
1 +
of anchors as determined from the centerlines of the anchor, or in the Scr,Na
consideration of: Vsa, either Vcb or Vcbg, and case of a group of anchors, from a line s
Eq. (D-14n) is valid for e'N
2
either Vcp or Vcpg. through a row of adjacent anchors. Ana
shall not exceed nAna0 where n is the If the loading on an anchor group is
D.4.1.4 For adhesive anchors
number of anchors in tension in the such that only some anchors are in
installed overhead and subjected to
group. (Refer to ACI 318 Figures tension, only those anchors that are in
tension resulting from sustained loading,
RD.5.2.1a and RD.5.2.1b and replace tension shall be considered when
Eq. (D-1) shall also be satisfied taking Nn
the terms 1.5hef and 3.0hef with ccr,Na and determining the eccentricity e'N for use in
= 0.75 Na for single anchors and Nn =
scr,Na, respectively.) Eq. (D-14n).
0.75 Nag for groups of anchors, whereby
Nua is determined from the sustained ANa0 is the projected area of the failure In the case where eccentric loading
load alone, e.g., the dead load and that surface of a single anchor without the exists about two orthogonal axes, the
portion of the live load acting that may influence of proximate edges in modification factor cec,Na shall be
be considered as sustained. Where accordance with Eq. (D-14c): computed for each axis individually and
shear loads act concurrently with the 2 the product of these factors used as
sustained tension load, interaction of ( )
ANa0 = scr,Na (D-14c) cec,Na in Eq. (D-14b).
tension and shear shall be checked in with D.5.3.12 The modification factor for
accordance with Section D.4.1.3.
scr,Na = as given by Eq. (D-14h) the edge effects for single adhesive
1 ACI 318-02 may also be used. The section references and terminology are different from those given in this report.

anchors or anchor groups loaded on where Section D.8.5, minimum member
tension is: thicknesses hmin as given in this report
kcp = 1.0 for hef < 2.5 in. (64 mm)
are applicable.
ced,Na = 1.0 when ca,min ccr,Na (D-14o)
kcp = 2.0 for hef 2.5 in. (64 mm)
Critical edge distance cac:
for Ca,min < C cr,Na
Na is calculated in accordance with Eq.
In lieu of ACI 318 Section D.8.6, cac may
(
ced,Na = 0.7 + 3.1 c
a,min
ccr,Na )
1.0 (D-14p) (D-14a)
be taken as follows:
D.5.3.13 When an adhesive anchor or Nag is calculated in accordance with Eq. 2
for h = hmin : cac = 3(h ef) + 1.63hef

a group of adhesive anchors is located in (D-14b) 32d
a region of a concrete member where
Ncb, Ncbg are determined in accordance
analysis indicates no cracking at service
with D.5.2.8 for h hef + 5 (ca,min)3/4
load levels, the nominal strength Na or Nag
of a single adhesive anchor or a group of D.8.7 For adhesive anchors that will where
adhesive anchors shall be calculated remain untorqued, the minimum edge
hef 8d : cac = 1.5hef
according to Eq. (D-14a) and Eq. (D-14b) distance shall be based on minimum
cover requirements for reinforcement in (hef)2 + 1.33hef
hef > 8d : cac =
with tk,uncr substituted for tk,cr in the
48d
calculation of the basic strength in 7.7. For adhesive anchors that will be
for all other h hmin : cac = 2.5hef
accordance with Eq. (D-14j). tk,uncr shall be torqued, the minimum edge distance
established based on tests in accordance and spacing shall be taken as 6do and Design strength in SDC C, D, E and F:
with AC308. The factor cg,Na0 shall be 5do, respectively, unless otherwise Where anchors are designed to resist
calculated in accordance with Eq. (D-14l) determined in accordance with AC308. earthquake forces in structures assigned
whereby the value of tk,max,uncr shall be to Seismic Design Categories C, D, E or
Bond strength determination:
calculated in accordance with Eq. (D-14q) F, the anchor strength shall be adjusted
and substituted for tk,max,cr in Eq. (D-14l). Bond strength values are a function of
in accordance with 2006 IBC Section
kc,uncr h . f concrete condition (cracked, un-
k,max,uncr = ef c (D-14q) 1908.1.16. The nominal steel shear
p.d cracked), drilling method (hammer drill,
strength, Vsa, shall be adjusted by V,seis.
D.5.3.14 When an adhesive anchor or core drill) and installation conditions
The nominal bond strength k,cr shall be
a group of adhesive anchors is located (dry, water-saturated, etc.). Bond
adjusted by N,seis.
in a region of a concrete member where strength values shall be modified with
analysis indicates no cracking at service the factor knn for cases where holes
load levels, the modification factor shall are drilled in water-saturated concrete
be taken as (kws), where the holes are water-filled at
the time of anchor installation (kwf), or
(D-14r)
where the application is carried out
cp,Na = 1.0 when ca,min cac
underwater (kuw).
(D-14s) Where applicable, the modified bond

max | ca,min ; ccr,Na | when c < c
cp,Na = a,min ac strength values shall be used in lieu of
ccr
k,cr and k,uncr in Equations (D-14d),
For all other cases, cp,Na = 1.0. (D-14f), (D-14j), (D-14m), and (D-14o).
The resulting nominal bond strength
D.6.3.2 The nominal pryout strength
shall be multiplied by the associated
of an adhesive anchor or group of
strength reduction factor fnn.
adhesive anchors shall not exceed
Minimum member thickness hmin,
(a) for a single adhesive anchor
anchor spacing smin and edge
Vcp = min | kcp . Na ; kcp . Ncb | (D-28a) distance cmin:
(b) for a group of adhesive anchors In lieu of ACI 318 Section D.8.3, values
Vcpg = min | kcp . Nag ; kcp . Ncbg | (D-28b) of cmin and smin as given in this report are
applicable. Likewise, in lieu of ACI 318

Table 1 DESIGN TABLE INDEX
Threaded rod Hilti HIS internally Deformed reinforcement

Design strength1 threaded insert
fractional metric fractional metric US EU Canadian
Steel Nsa, Vsa Table 7 Table 11 Table 15 Table 19 Table 23 Table 27 Table 31
Concrete Npn, Nsb, Nsbg, Ncb, Ncbg, Vcb, Vcbg, Vcp, Vcpg Table 8 Table 12 Table 16 Table 20 Table 24 Table 28 Table 32
hammer-drilled holes Table 9 Table 13 Table 17 Table 21 Table 25 Table 29 Table 33
Bond2 N ,N
a ag diamond cored holes Table 10 Table 14 Table 18 Table 22 Table 26 Table 30 Table 34
1 Ref. ACI 318 Section D.4.1.2
2 See Section 4.1
Bond strength design flowchart
Cracked Concrete Un-cracked Concrete
Hammer Drilled Hammer Drilled Diamond Cored
Dry Water Dry Water Water Under Dry Water

(D) Saturated (D) Saturated Filled Water (D) Saturated
Installation
(borehole)
Condition
(WS) (WS) (WF) (UW) (WS)
fD fWS fD fWS fWF fUW fD fWS
k,cr k,uncr k,uncr
Table 2 TENSILE PROPERTIES OF COMMON CARBON STEEL THREADED ROD MATERIALS1
Minimum Minimum
Reduction
THREADED ROD SPECIFICATION specified specified yield f /f Elongation, Specification for nuts6
of Area,
ultimate strength 0.2% uta ya min. %5
min. %
strength futa offset fya
ASTM A 1932 Grade B7 psi 125,000 105,000
1.19 16 50 ASTM A 563 Grade DH
2-1/2 in. ( 64 mm) (MPa) (862) (724)
ASTM F 568M3 Class 5.8
MPa 500 400 1.25 10 35 DIN 934 (8-A2K)
M5 (1/4 in.) to M24 (1 in.)
(psi) (72,500) (58,000) ASTM A 563 Grade DH7
(equivalent to ISO 898-1)
MPa 800 640
ISO 898-14 Class 8.8 1.25 12 52 DIN 934 (8-A2K)
(psi) (116,000) (92,800)
1 Hilti HIT-RE 500-SD may be used in conjunction with all grades of continuously threaded carbon steel rod (all-thread) that conform to the code and that have thread
characteristics comparable with ANSI B1.1 UNC Coarse Thread Series or ANSI B1.13M M Profile Metric Thread Series. Values for threaded rod types and associated nuts
supplied by Hilti are provided here.
2 Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service
3 Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners
4 Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs
5 Based on 2-in. (50 mm) gauge length except for A193 and A449, which are based on a gauge length of 4D and ISO 898 which is based on 5D.
6 Nuts of other grades and styles having specified proof load stresses greater than the specified grade and style are also suitable. Nuts must have specified proof load
stresses equal to or greater than the minimum tensile strength of the specified threaded rod.
7 Nuts for fractional rods.
Table 3 TENSILE PROPERTIES OF COMMON STAINLESS STEEL THREADED ROD MATERIALS1
Minimum Minimum
THREADED ROD SPECIFICATION specified specified yield f /f Elongation, Reduction of Specification for nuts4
ultimate strength 0.2% uta ya min. % Area, min. %
ASTM F 5932 CW1 (316) psi 100,000 65,000
1.54 20 - F 594
1/4 to 5/8 in. (MPa) (689) (448)
ASTM F 5932 CW2 (316) psi 85,000 45,000
1.89 25 - F 594
3/4 to 1-1/2 in.(MPa) (586) (310)
ISO 3506-13 A4-70 MPa 700 450
1.56 40 - ISO 4032
M8 M24 (psi) (101,500) (65,250)
ISO 3506-13 A4-50 MPa 500 210
2.00 40 - ISO 4032
M27 M30 (psi) (72,500) (30,450)
1 Hilti HIT-RE 500-SD may be used in conjunction with all grades of continuously threaded stainless steel rod (all-thread) that conform to the code and that have thread
characteristics comparable with ANSI B1.1 UNC Coarse Thread Series or ANSI B1.13M M Profile Metric Thread Series. Values for threaded rod types and associated
nuts supplied by Hilti are provided here.
2 Standard Steel Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
3 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
4 Nuts of other grades and styles having specified proof load stresses greater than the specified grade and style are also suitable. Nuts must have specified proof load
stresses equal to or greater than the minimum tensile strength of the specified threaded rod.

Table 4 TENSILE PROPERTIES OF FRACTIONAL AND METRIC HIS-N AND HIS-RN INSERTS
Minimum specified Minimum specified yield

HILTI HIS AND HIS-R INSERTS
ultimate strength futa strength fya
DIN 1651 9SMNPB28K MPa
490 410
Carbon Steel (psi)
(71,050) (59,450)
3/8 and M8 to M10
DIN 1651 9SMNPB28K
MPa 460 375
Carbon Steel
(psi) (66,700) (54,375)
1/2 to 3/4 and M12 to M20
DIN 17440 X5CrNiMo17122 MPa 700 350
Stainless Steel (psi) (101,500) (50,750)
Table 5 TENSILE PROPERTIES OF COMMON BOLTS, CAP SCREWS AND STUDS FOR USE WITH HIS-N
AND HIS-RN INSERTS1,2
Minimum Minimum
Reduction
BOLT, CAP SCREW OR STUD specified specified yield f /f Elongation, Specification for nuts6
of Area,
SPECIFICATION ultimate strength 0.2% uta ya min.
min.
psi 120,000 92,000
SAE J4293 Grade 5 1.30 14 35 SAE J995
(MPa) (828) (634)
psi 120,000 92,000 A 563 C, C3, D, DH,
ASTM A 3254 1/2 to 1-in. 1.30 14 35
(MPa) (828) (634) DH3 Heavy Hex
ASTM F A1935 Grade B8M
psi 110,000 95,000 1.16 15 45 F 5947
(AISI 316) for use with
(MPa) (759) (655)
HIS-RN
ASTM F A1935 Grade B8M
psi 125,000 100,000 1.25 12 35 F 5947
(AISI 316) for use with
(MPa) (862) (690)
HIS-RN
1 Minimum Grade 5 bolts, cap screws or studs should be used in conjunction with carbon steel HIS inserts.
2 Use only stainless steel bolts, cap screws or studs with HIS-R inserts.
3 Mechanical and Material Requirements for Externally Threaded Fasteners
4 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
5 Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service
6 Nuts must have specified minimum proof load stress equal to or greater than the specified minimum full-size tensile strength of the specified stud.
7 Nuts for stainless steel studs must be of the same alloy group as the specified stud.
Table 6 TENSILE PROPERTIES OF COMMON REINFORCING BARS
Minimum Minimum
REINFORCING BAR SPECIFICATION specified ultimate specified yield
strength futa strength fya
psi 90,000 60,000
ASTM A 6151 Gr. 60
(MPa) (620) (414)
psi 60,000 40,000
ASTM A 6151 Gr. 40
(MPa) (414) (276)
MPa 550 500
DIN 4882 BSt 500
(psi) (79,750) (72,500)
MPa 540 400
CAN/CSA-G30.183 Gr. 400
(psi) (78,300) (58,000)
1 Standard Specification for Deformed and Plain Carbon Steel Bars for Concrete Reinforcement
2 Reinforcing steel; reinforcing steel bars; dimensions and masses
3 Billet-Steel Bars for Concrete Reinforcement

Table 7 STEEL DESIGN INFORMATION FOR FRACTIONAL THREADED ROD1
Nominal rod diameter (in.)

DESIGN INFORMATION Symbol Units
3/8 1/2 5/8 3/4 7/8 1 1-1/4
in. 0.375 0.5 0.625 0.75 0.875 1 1.25
Rod O.D. d
(mm) (9.5) (12.7) (15.9) (19.1) (22.2) (25.4) (31.8)
in.2 0.0775 0.1419 0.2260 0.3345 0.4617 0.6057 0.9691
Rod effective cross-sectional area Ase
(mm2) (50) (92) (146) (216) (298) (391) (625)
lb 5,619 10,288 16,385 24,251 33,472 43,912 70,258
Nsa
(kN) (25.0) (45.8) (72.9) (107.9) (148.9) (195.3) (312.5)
ISO 898-1 Class 5.82
Nominal strength as governed

by steel strength lb 2,809 6,173 9,831 14,550 20,083 26,347 42,155
Vsa
(kN) (12.5) (27.5) (43.7) (64.7) (89.3) (117.2) (187.5)
Reduction for seismic shear aV,seis - 0.70
Strength reduction factor f for tension2 f - 0.65
Strength reduction factor f for shear2 f - 0.60
lb 9,687 17,737 28,249 41,812 57,711 75,711 121,135
Nsa
Nominal strength as governed (kN) (43.1) (78.9) (125.7) (186.0) (256.7) (336.8) (538.8)
ASTM A 193 B72

Vsa
(kN) (21.5) (47.3) (75.4) (111.6) (154.0) (202.1) (323.3)
lb 7,750 14,190 22,600 28,432 39,244 51,483 82,372
ASTM F593, CW Stainless2
Nsa
Nominal strength as governed (kN) (34.5) (63.1) (100.5) (126.5) (174.6) (229.0) (366.4)
Vsa
(kN) (17.2) (.37.9) (60.3) (75.9) (104.7) (137.4) (219.8)
For SI: 1 inch = 25.4 mm, 1 lbf = 4.448 N, 1 psi = 0.006897 MPa
For pound-inch units: 1 mm = 0.03937 inches, 1 N = 0.2248 lbf, 1 MPa = 145.0 psi
1 Values provided for common rod material types based on published strengths and calculated in accordance with ACI 318-05 Eq. (D-3) and Eq. (D-20). Other material
specifications are admissible. Use nuts and washers appropriate for the rod strength.
2 For use with the load combinations of ACI 318-05 Section 9.2. See ACI 318-05 Section D.4.4.

Table 8 CONCRETE BREAKOUT DESIGN INFORMATION FOR FRACTIONAL THREADED ROD IN HOLES
DRILLED WITH A HAMMER DRILL AND CARBIDE BIT1

3/8 1/2 5/8 3/4 7/8 1 1-1/4
in-lb 17
Effectiveness factor for cracked concrete kc,cr
(SI) (7.1)
in-lb 24
Effectiveness factor for un-cracked concrete kc,uncr
(SI) (10)
in. 1-7/8 2-1/2 3-1/8 3-3/4 4-3/8 5 6-1/4
Min. anchor spacing smin
(mm) (48) (64) (79) (95) (111) (127) (159)
in. 1-7/8 2-1/2 3-1/8 3-3/4 4-3/8 5 6-1/4
Min. edge distance cmin
(mm) (48) (64) (79) (95) (111) (127) (159)
in. hef + 1-1/4
Minimum member thickness hmin hef + 2d o
(mm) (hef + 30)
Critical edge distance splitting
cac - See Strength Design provisions above
(for un-cracked concrete)
Strength reduction factor for tension,
f - 0.65
concrete failure modes, Condition B2
Strength reduction factor for shear,
f - 0.70
1 For additional setting information, see installation instructions.
2 Values provided for post-installed anchors with category as determined from ACI 355.2 given for Condition B without supplementary reinforcement.

Table 9 BOND STRENGTH DESIGN INFORMATION FOR FRACTIONAL THREADED ROD IN HOLES DRILLED
WITH A HAMMER DRILL AND CARBIDE BIT1,4

3/8 1/2 5/8 3/4 7/8 1 1-1/4
psi 1,092 1,073 1,044 999 917 852 732
Characteristic bond strength and
k,cr (N/mm2) (7.5) (7.4) (7.2) (6.9) (6.3) (5.9) (5.0)
Temperature range A3
minimum anchor embedment in

cracked concrete in. 2.43 2.81 3.14 3.44 3.71 4.0 5.0
h
ef,min (mm) (62) (71) (80) (87) (94) (102) (127)
psi 2,283 2,236 2,142 2,067 2,002 1,946 1,862
k,uncr (N/mm2) (15.7) (15.4) (14.8) (14.3) (13.8) (13.4) (12.8)
un-cracked concrete in. 2.43 2.81 3.14 3.44 3.71 4.0 5.0
h
ef,min (mm) (62) (71) (80) (87) (94) (102) (127)
psi 444 431 379 345 316 294 260
k,cr (N/mm2) (3.1) (3.0) (2.6) (2.4) (2.2) (2.0) (1.8)
Temperature range B3
minimum anchor embedment

in cracked concrete2 in. 1.73 2.20 3.61 3.01 3.50 4.0 5.0
h
ef,min (mm) (44) (56) (66) (76) (89) (102) (127)
psi 788 772 739 714 691 672 643
k,uncr (N/mm2) (5.4) (5.3) (5.1) (4.9) (4.8) (4.6) (4.4)
un-cracked concrete2 in. 1.73 2.20 3.61 3.01 3.50 4.0 5.0
h
ef,min (mm) (44) (56) (66) (76) (89) (102) (127)
Permissible installation conditions
Dry concrete fd - 0.65 0.65 0.65 0.65 0.55 0.55 0.55

fws - 0.55 0.55 0.45 0.45 0.45 0.45 0.45
Water-saturated concrete
kws - 1.0 1.0 1.0 1.0 1.0 0.99 0.94
fwf - 0.45 0.45 0.45 0.45 0.45 0.45 0.45
Water-filled hole
kwf - 1.00 1.00 0.96 0.91 0.87 0.84 0.79
fuw - 0.45 0.45 0.45 0.45 0.45 0.45 0.45
Underwater application
kuw - 0.95 0.94 0.94 0.93 0.92 0.92 0.91
1 Bond strength values correspond to concrete compressive strength range 2,500 psi fc 4,500 psi. For 4,500 psi fc 6,500 psi, tabulated characteristic
bond strength may be increased by 6%. For 6,500 psi fc 8,000 psi, tabulated characteristic bond strength may be increased by 10%.
2 Bond strength values are for sustained loads including dead and live loads. For short-term loads including wind and seismic, bond strengths may be increased
40%.
3 Temperature range A: Max. short term temperature = 110F (43C), max. long term temperature = 80F (26C).
Temperature range B: Max. short term temperature = 162F (72C), max. long term temperature = 110F (43C).
Short term elevated concrete temperatures are those that occur over brief intervals, e.g., as a result of diurnal cycling. Long term concrete temperatures are roughly
constant over significant periods of time.
4 For structures assigned to SDC C, D, E or F, bond strength values shall be multiplied by aN,seis = 0.65.

Table 10 BOND STRENGTH DESIGN INFORMATION FOR FRACTIONAL THREADED ROD IN HOLES DRILLED
WITH A CORE DRILL1,4

3/8 1/2 5/8 3/4 7/8 1 1-1/4
psi 1,740 1,703 1,553 1,441 1,356 1,282 1,169
Temperature
Characteristic bond strength and k,uncr

range A3
(N/mm2) (12.0) (11.7) (10.7) (9.9) (9.4) (8.8) (8.1)

un-cracked concrete in. 2.43 2.81 3.14 3.44 3.71 4.0 5.0
hef,min
(mm) (62) (71) (80) (87) (94) (102) (127)
psi 601 588 536 497 468 442 404
Temperature

range B3
(N/mm2) (4.1) (4.1) (3.7) (3.4) (3.2) (3.1) (2.8)

un-cracked concrete2 in. 1.57 2.0 2.5 3.0 3.5 4.0 5.0
hef,min
(mm) (40) (51) (64) (76) (89) (102) (127)
Dry concrete fd - 0.65 0.65 0.55 0.55 0.55 0.45 0.45
Permissible
installation
conditions
fws - 0.55 0.55 0.45 0.45 0.45 0.45 0.45

kws - 1.00 1.00 1.00 1.00 1.00 0.95 0.88
1 Bond strength values correspond to concrete compressive strength range 2,500 psi fc 4,500 psi. For 4,500 psi fc 6,500 psi, tabulated characteristic bond
strength may be increased by 6%. For 6,500 psi fc 8,000 psi, tabulated characteristic bond may be increased by 10%.
2 Characteristic bond strengths are for sustained loads including dead and live loads. For short-term loads including wind and seismic, bond strengths may be
increased 40%.
4 Bond strength values applicable to SDC A and B only.
Table 11 STEEL DESIGN INFORMATION FOR METRIC THREADED ROD1
Nominal rod diameter (mm)

8 10 12 16 20 24 27 30
Rod O.D. mm 8 10 12 16 20 24 27 30
d
(in.) (0.31) (0.39) (0.47) (0.63) (0.79) (0.94) (1.06) (1.18)
Rod effective cross-sectional area mm2 36.6 58 84.3 157 245 353 459 561
Ase
(in.2) (0.057) (0.090) (0.131) (0.243) (0.380) (0.547) (0.711) (0.870)
kN 18.3 29.0 42.2 78.5 122.5 176.5 229.5 280.5
Nsa
Nominal strength as governed (lb) (4,114) (6,519) (9,476) (17,647) (27,539) (39,679) (51,594) (63,059)
ISO 898-1 Class 5.8
by steel strength
kN 9.2 14.5 25.3 47.1 73.5 105.9 137.7 168.3
Vsa
(lb) (2,057) (3,260) (5,685) (10,588) (16,523) (23,807) (30,956) (37,835)
kN 29.3 46.4 67.4 125.6 196.0 282.4 367.2 448.8
Nsa
ISO 898-1 Class 8.8
by steel strength
kN 14.6 23.2 40.5 75.4 117.6 169.4 220.3 269.3
Vsa
(lb) (3,291) (5,216) (9,097) (16,942) (26,438) (38,092) (49,530) (60,537)
ISO 3506-1 Class A4 Stainless3
kN 25.6 40.6 59.0 109.9 171.5 247.1 229.5 280.5

Nsa
by steel strength
kN 12.8 20.3 35.4 65.9 102.9 148.3 137.7 168.3
Vsa
(lb) (2,880) (4,564) (7,960) (14,824) (23,133) (33,330) (30,956) (37,835)
3 A4-70 Stainless (M8- M24); A4-502 Stainless (M27- M30)

Table 12 CONCRETE BREAKOUT DESIGN INFORMATION FOR METRIC THREADED ROD IN HOLES DRILLED WITH
A HAMMER DRILL AND CARBIDE BIT1

8 10 12 16 20 24 27 30
SI 7.1
(in-lb) (17)
SI 10
(in-lb) (24)
mm 40 50 60 80 100 120 135 150
Min. anchor spacing smin
(in.) (1.6) (2.0) (2.4) (3.2) (3.9) (4.7) (5.3) (5.9)
mm 40 50 60 80 100 120 135 150
Min. edge distance cmin
(in.) (1.6) (2.0) (2.4) (3.2) (3.9) (4.7) (5.3) (5.9)
mm hef + 30
(in.) (hef + 1-1/4)
f - 0.65
f - 0.70

Table 13 BOND STRENGTH DESIGN INFORMATION FOR METRIC THREADED ROD IN HOLES DRILLED WITH A
HAMMER DRILL AND CARBIDE BIT1,4

8 10 12 16 20 24 27 30
N/mm2 7.5 7.5 7.5 7.2 6.7 6.0 5.7 5.3
Characteristic bond strength and k,cr
(psi) (1,092) (1,092) (1,092) (1,044) (972) (877) (831) (768)

in cracked concrete mm 57 63 69 80 89 98 108 120
hef,min
(in.) (2.23) (2.49) (2.73) (3.15) (3.52) (3.86) (4.25) (4.72)
N/mm2 15.6 15.6 15.6 14.8 14.1 13.6 13.3 13.0
(psi) (2,264) (2,264) (2,264) (2,142) (2,039) (1,974) (1,927) (1,880)
in un-cracked concrete mm 57 63 69 80 89 98 108 120
hef,min
(in.) (2.23) (2.49) (2.73) (3.15) (3.52) (3.86) (4.25) (4.72)
N/mm2 3.1 3.1 3.1 2.6 2.3 2.1 2.0 1.9
Characteristic bond strength and k,cr
(psi) (444) (444) (444) (379) (336) (303) (287) (268)

in cracked concrete2 mm 40 46 53 67 80 96 108 120
hef,min
(in.) (1.57) (1.80) (2.10) (2.62) (3.15) (3.78) (4.25) (4.72)
N/mm2 5.4 5.4 5.4 5.1 4.9 4.7 4.6 4.5
(psi) (781) (781) (781) (739) (704) (681) (665) (649)
in un-cracked concrete2 mm 40 46 53 67 80 96 108 120
hef,min
(in.) (1.57) (1.80) (2.10) (2.62) (3.15) (3.78) (4.25) (4.72)
Dry concrete fd - 0.65 0.65 0.65 0.65 0.65 0.55 0.55 0.55
fws - 0.55 0.55 0.55 0.45 0.45 0.45 0.45 0.45
Permissible installation
kws - 1.00 1.00 1.00 1.00 1.00 1.00 0.98 0.95
conditions
fwf - 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45

Water-filled hole
kwf - 1.00 1.00 1.00 0.96 0.90 0.86 0.83 0.81
fuw - 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45
kuw - 0.95 0.95 0.95 0.94 0.93 0.92 0.92 0.91
For SI: 1 inch = 25.4 mm, 1 lbf = 4.448 N, 1 psi = 0.006897MPa
1 Bond strength values correspond to concrete compressive strength range 2,500 psi fc 4,500 psi. For 4,500 psi fc 6,500 psi, tabulated characteristic bond strength
may be increased by 6%. For 6,500 psi fc 8,000 psi, tabulated characteristic bond strength may be increased by 10%.
2 Characteristic bond strengths are for sustained loads including dead and live loads. For short-term loads including wind and seismic, bond strengths may be increased 40%.
Short term elevated concrete temperatures are those that occur over brief intervals, e.g., as a result of diurnal cycling. Long term concrete temperatures are roughly constant
over significant periods of time.

Table 14 BOND STRENGTH DESIGN INFORMATION FOR METRIC THREADED ROD IN HOLES DRILLED WITH A
CORE DRILL1,4

8 10 12 16 20 24 27 30
N/mm2 12.0 12.0 12.0 10.7 9.7 9.0 8.6 8.3
Temperature

range A3
(psi) (1,740) (1,740) (1,740) (1,553) (1,413) (1,310) (1,254) (1,197)

in un-cracked concrete mm 56 63 69 80 89 98 108 120
hef,min
(in.) (2.19) (2.49) (2.73) (3.15) (3.52) (3.86) (4.25) (4.72)
N/mm2 4.1 4.1 4.1 3.7 3.4 3.1 3.0 2.8
Temperature

range B3
(psi) (601) (601) (601) (536) (488) (452) (433) (413)

in un-cracked concrete2 mm 40 41 48 64 80 96 108 120
hef,min
(in.) (1.57) (1.61) (1.89) (2.52) (3.15) (3.78) (4.25) (4.72)
Dry concrete fd - 0.65 0.65 0.65 0.55 0.55 0.55 0.45 0.45
Permissible
installation
conditions
fws - 0.55 0.55 0.55 0.45 0.45 0.45 0.45 0.45

kws - 1.00 1.00 1.00 1.00 1.00 0.97 0.93 0.90
Table 15 STEEL DESIGN INFORMATION FOR FRACTIONAL HILTI HIS-N AND HIS-RN INSERTS1
Nominal bolt/cap screw diameter (in.)

3/8 1/2 5/8 3/4
in. 0.65 0.81 1 1.09
HIS insert O.D. d
(mm) (16.5) (20.5) (25.4) (27.6)
in.2 0.0775 0.1419 0.2260 0.3345
Bolt effective cross-sectional area Ase
(mm2) (50) (92) (146) (216)
in.2 0.178 0.243 0.404 0.410
HIS insert effective cross-sectional area Ainsert
(mm2) (115) (157) (260) (265)
lb 9,296 17,020 27,108 40,122
Nominal strength as governed by Nsa
(kN) (41.3) (75.7) (120.6) (178.5)
steel strength A 193 B7
bolt/cap screw lb 5,577 10,212 16,265 24,073
Vsa
ASTM A 193 B7
(kN) (24,8) (45.4) (72.3) (107.1)

Nominal strength as governed by lb 12,648 16,195 26,926 27,362
Nsa
steel strength HIS-N insert (kN) (56.3) (72.0) (119.8) (121.7)
lb 7,750 14,190 22,599 28,432
Nominal strength as governed by steel Nsa
(kN) (34.5) (63.1) (100.5) (126.5)
ASTM F A193 Grade B8M SS
strength ASTM F A193 Grade

B8M SS bolt/cap screw lb 4,650 8,514 13,560 17,059
Vsa
(kN) (20.7) (37.9) (60.3) (75.9)
Nominal strength as governed by steel lb 18,068 24,645 40,974 41,638
Nsa
strength HIS-RN insert (kN) (80.4) (109.6) (182.3) (185.2)
2 For use with the load combinations of ACI 318-05 Section 9.2. See ACI 318-05 Section D.4.4. Values correspond to a ductile steel element.
Table 16 CONCRETE BREAKOUT DESIGN INFORMATION FOR FRACTIONAL HILTI HIS-N AND HIS-RN INSERTS 1

3/8 1/2 5/8 3/4
in. 4-3/8 5 6-3/4 8-1/8
Effective embedment depth hef
(mm) (110) (125) (170) (205)
in-lb 17
(SI) (7.1)
in-lb 24
(SI) (10)
in. 3-1/4 4 5 5-1/2
Minimum anchor spacing smin
(mm) (83) (102) (127) (140)
in. 3-1/4 4 5 5-1/2
Minimum edge distance cmin
(mm) (83) (102) (127) (140)
in. 5.9 6.7 9.1 10.6
Minimum member thickness hmin
(mm) (150) (170) (230) (270)
f - 0.65
f - 0.70

Table 17 BOND STRENGTH DESIGN INFORMATION FOR FRACTIONAL HILTI HIS-N AND HIS-RN INSERTS IN HOLES
DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1,4

3/8 1/2 5/8 3/4
in. 4-3/8 5 6-3/4 8-1/8
(mm) (110) (125) (170) (205)
in. 0.65 0.81 1 1.09
HIS insert O.D. d
(mm) (16.5) (20.5) (25.4) (27.6)
Characteristic bond strength in psi 1040 957 845 806
Temperature
k,cr
range A3
cracked concrete (N/mm2) (7.2) (6.6) (5.8) (5.6)

k,uncr
un-cracked concrete (N/mm2) (14.6) (14.0) (13.4) (13.2)
Temperature
k,cr
range B3
cracked concrete2 (N/mm2) (2.6) (2.3) (2.0) (1.9)

k,uncr
un-cracked concrete2 (N/mm2) (5.1) (4.8) (4.6) (4.5)
Dry concrete fd - 0.65 0.65 0.55 0.55
fws - 0.45 0.45 0.45 0.45

kws - 1.00 1.00 0.99 0.97
conditions
fwf - 0.45 0.45 0.45 0.45

Water-filled hole
kwf - 0.95 0.89 0.84 0.82
fuw - 0.45 0.45 0.45 0.45
kuw - 0.93 0.93 0.92 0.92
Short term elevated concrete temperatures are those that occur over brief intervals, e.g., as a result of diurnal cycling. Long term concrete temperatures are roughly constant over
significant periods of time.

Table 18 BOND STRENGTH DESIGN INFORMATION FOR FRACTIONAL HILTI HIS-N AND HIS-RN INSERTS IN HOLES
DRILLED WITH A CORE DRILL1,4

3/8 1/2 5/8 3/4
in. 4-3/8 5 6-3/4 8-1/8
(mm) (110) (125) (170) (205)
in. 0.65 0.81 1 1.09
HIS insert O.D. d
(mm) (16.5) (20.5) (25.4) (27.6)
Temperature Temperature
range A3
Characteristic bond strength in k,uncr psi 1534 1403 1282 1235

un-cracked concrete (N/mm2) (10.6) (9.7) (8.8) (8.5)
range B3
Characteristic bond strength in k,uncr psi 530 484 442 426

un-cracked concrete2 (N/mm2) (3.7) (3.3) (3.1) (2.9)
Dry concrete fd - 0.55 0.55 0.45 0.45

Permissible
installation
conditions
fws - 0.45 0.45 0.45 0.45

kws - 1.00 1.00 0.95 0.92

Table 19 STEEL DESIGN INFORMATION FOR METRIC HILTI HIS-N AND HIS-RN INSERTS1
Nominal bolt/cap screw diameter (mm)

8 10 12 16 20
mm 12.5 16.5 20.5 25.4 27.6
HIS insert O.D. d
(in.) (0.49) (0.65) (0.81) (1.00) (1.09)
mm2 36.6 58 84.3 157 245
Bolt effective cross-sectional area Ase
(in.2) (0.057) (0.090) (0.131) (0.243) (0.380)
mm2 51.5 108 169.1 256.1 237.6
HIS insert effective cross-sectional area Ainsert
(in.2) (0.080) (0.167) (0.262) (0.397) (0.368)
kN 29.3 46.4 67.4 125.6 196.0
Nominal strength as governed Nsa
(lb) (6,582) (10,431) (15,161) (28,236) (44,063)
by steel strength ISO 898-1
Class 8.8 bolt/cap screw kN 17.6 27.8 40.5 75.4 117.6
Vsa
ISO 898-1 Class 8.8
(lb) (3,949) (6,259) (9,097) (16,942) (26,438)

Nominal strength as governed kN 25.2 52.9 77.8 117.8 109.3
Nsa
by steel strength HIS-N insert (lb) (5,669) (11,894) (17,488) (26,483) (24,573)
Strength reduction factor f
f - 0.65
for tension2
f - 0.60
for shear2
kN 25.6 40.6 59.0 109.9 171.5
Nominal strength as governed by Nsa
(lb) (5,760) (9,127) (13,266) (24,706) (38,555)
ISO 3506-1 Class A4-70 Stainless
steel strength ISO 3506-1 Class

A4-70 Stainless bolt/cap screw kN 15.4 24.4 35.4 65.9 102.9
Vsa
(lb) (3,456) (5,476) (7,960) (14,824) (23,133)
Nominal strength as governed kN 36.0 75.6 118.4 179.3 166.3
Nsa
by steel strength HIS-RN insert (lb) (8,099) (16,991) (26,612) (40,300) (37,394)
Strength reduction factor f for
f - 0.75
tension2
f - 0.65
for shear2
1 Values provided for common rod material types based on published strengths and calculated in accordance with ACI 318-05 Eq. (D-3) and Eq. (D-20). Other
material specifications are admissible. Use nuts and washers appropriate for the rod strength.
2 For use with the load combinations of ACI 318-05 Section 9.2. See ACI 318-05 Section D.4.4. Values correspond to a ductile steel element.
Table 20 CONCRETE BREAKOUT DESIGN INFORMATION FOR METRIC HILTI HIS-N AND HIS-RN INSERTS 1

8 10 12 16 20
mm 90 110 125 170 205
(in.) (3.5) (4.3) (4.9) (6.7) (8.1)
Effectiveness factor for SI 7.1
kc,cr
cracked concrete (in-lb) (17)
Effectiveness factor for SI 10
kc,uncr
un-cracked concrete (in-lb) (24)
mm 40 50 60 80 100
Minimum anchor spacing smin
(in.) (1.6) (2.0) (2.4) (3.2) (3.9)
mm 40 50 60 80 100
(in.) (1.6) (2.0) (2.4) (3.2) (3.9)
mm 120 150 170 230 270
Minimum member thickness hmin
(in.) (4.7) (5.9) (6.7) (9.1) (10.6)
f - 0.65
f - 0.70

Table 21 BOND STRENGTH DESIGN INFORMATION FOR METRIC HILTI HIS-N AND HIS-RN INSERTS IN
HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1,4

8 10 12 16 20
mm 90 110 125 170 205
(in.) (3.5) (4.3) (4.9) (6.7) (8.1)
mm 12.5 16.5 20.5 25.4 27.6
HIS insert O.D. d
(in.) (0.49) (0.65) (0.81) (1.00) (1.09)
Characteristic bond strength N/mm2 7.4 7.2 6.6 5.8 5.6
Temperature
k,cr
range A3
in cracked concrete (psi) (1,080) (1,040) (957) (845) (806)

tk,uncr
in un-cracked concrete (psi) (2,245) (2,124) (2,030) (1,946) (1,908)
Temperature
k,cr
range B3
in cracked concrete2 (psi) (433) (374) (330) (292) (278)

k,uncr
in un-cracked concrete2 (psi) (775) (733) (701) (672) (659)
Dry concrete fd - 0.65 0.65 0.65 0.55 0.55
fws - 0.55 0.45 0.45 0.45 0.45
kws - 1.00 1.00 1.00 0.99 0.97
conditions
fwf - 0.45 0.45 0.45 0.45 0.45

Water-filled hole
kwf - 1.00 0.95 0.89 0.84 0.82
fuw - 0.45 0.45 0.45 0.45 0.45
kuw - 0.94 0.93 0.93 0.92 0.92
increased 40%.
Short term elevated concrete temperatures are those that occur over brief intervals, e.g., as a result of diurnal cycling. Long term concrete temperatures are
roughly constant over significant periods of time.

Table 22 BOND STRENGTH DESIGN INFORMATION FOR METRIC HILTI HIS-N AND HIS-RN INSERTS IN
HOLES DRILLED WITH A CORE DRILL 1,4

8 10 12 16 20
mm 90 110 125 170 205
(in.) (3.5) (4.3) (4.9) (6.7) (8.1)
mm 12.5 16.5 20.5 25.4 27.6
HIS insert O.D. d
(in.) (0.49) (0.65) (0.81) (1.00) (1.09)
Temperature Temperature
range A3

k,cr
in un-cracked concrete (psi) (1,712) (1,534) (1,403) (1,282) (1,235)
range B3

k,cr
in un-cracked concrete2 (psi) (591) (530) (484) (442) (426)
Dry concrete fd - 0.65 0.55 0.45 0.45 0.45

Permissible
installation
conditions
fws - 0.55 0.45 0.45 0.45 0.45

kws - 1.0 1.0 1.0 0.95 0.92
increased 40%.

Table 23 STEEL DESIGN INFORMATION FOR FRACTIONAL REINFORCING BARS1
Bar size
#3 #4 #5 #6 #7 #8 #9 #10
in. 3/8 1/2 5/8 3/4 7/8 1 1-1/8 1-1/4
Nominal bar diameter d
(mm) (9.5) (12.7) (15.9) (19.1) (22.2) (25.4) (28.6) (31.8)
in.2 0.11 0.2 0.31 0.44 0.6 0.79 1.0 1.27
Bar effective cross-sectional area Ase
(mm2) (71) (129) (200) (284) (387) (510) (645) (819)
lb 6,600 12,000 18,600 26,400 36,000 47,400 60,000 76,200
Nominal strength as Nsa
(kN) (29.4) (53.4) (82.7) (117.4) (160.1) (210.9) (266.9) (339.0)
governed by steel
lb 3,960 7,200 11,160 15,840 21,600 28,440 36,000 45,720
ASTM A 615 Gr. 40
strength
Vsa
(kN) (17.6) (32.0) (49.6) (70.5) (96.1) (126.5) (160.1) (203.4)
Strength reduction factor
f - 0.75
f for tension2
f - 0.65
f for shear2
lb 9,900 18,000 27,900 39,600 54,000 71,100 90,000 114,300
Nominal strength as Nsa
(kN) (44.0) (80.1) (124.1) (176.2) (240.2) (316.3) (400.4) (508.5)
governed by steel
ASTM A 615 Gr. 60
strength lb 5,940 10,800 16,740 23,760 32,400 42,660 54,000 68,580

Vsa
(kN) (26.4) (48.0) (74.5) (105.7) (144.1) (189.8) (240.2) (305.1)
f - 0.75
f for tension2
f - 0.65
f for shear2

Table 24 CONCRETE BREAKOUT DESIGN INFORMATION FOR FRACTIONAL REINFORCING BARS IN
HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT1
Bar size
#3 #4 #5 #6 #7 #8 #9 #10
Effectiveness factor for in-lb 17
kc,cr
cracked concrete (SI) (7.1)
Effectiveness factor for in-lb 24
kc,uncr
un-cracked concrete (SI) (10)
in. 1-7/8 2-1/2 3-1/8 3-3/4 4-3/8 5 5-5/8 6-1/4
Minimum bar spacing smin
(mm) (48) (64) (79) (95) (111) (127) (143) (159)
in. 1-7/8 2-1/2 3-1/8 3-3/4 4-3/8 5 5-5/8 6-1/4
(mm) (48) (64) (79) (95) (111) (127) (143) (159)
in. hef + 1-1/4
(mm) (hef + 30)
Strength reduction factor for
tension, concrete failure f - 0.65
modes, Condition B2
shear, concrete failure f - 0.70
modes, Condition B2

Table 25 BOND STRENGTH DESIGN INFORMATION FOR FRACTIONAL REINFORCING BARS IN HOLES
DRILLED WITH A HAMMER DRILL AND CARBIDE BIT1,4
Bar size
#3 #4 #5 #6 #7 #8 #9 #10
Characteristic bond psi 1,092 1,073 1,044 999 917 852 799 732
k,cr
strength and minimum (N/mm2) (7.5) (7.4) (7.2) (6.9) (6.3) (5.9) (5.5) (5.0)
anchor embedment in in. 2.43 2.81 3.14 3.44 3.71 4.00 4.50 5.00
cracked concrete hef,min
(mm) (62) (71) (80) (87) (94) (102) (114) (127)
Characteristic bond psi 2,264 2,236 2,142 2,067 2,002 1,946 1,899 1,862
k,uncr
un-cracked concrete hef,min
(mm) (62) (71) (80) (87) (94) (102) (114) (127)
Characteristic bond psi 444 431 379 345 316 294 276 260
k,cr
cracked concrete2 hef,min
(mm) (44) (56) (66) (76) (89) (102) (114) (127)
k,uncr
un-cracked concrete2 hef,min
(mm) (44) (56) (66) (76) (89) (102) (114) (127)
Dry concrete fd - 0.65 0.65 0.65 0.65 0.55 0.55 0.55 0.55
fws - 0.55 0.55 0.45 0.45 0.45 0.45 0.45 0.45
Water-saturated
concrete kws - 1.00 1.00 1.00 1.00 1.00 0.99 0.97 0.94
conditions
fwf - 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45

Water-filled hole
kwf - 1.00 1.00 0.96 0.91 0.87 0.84 0.82 0.79
fuw - 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45
kuw - 0.95 0.94 0.94 0.93 0.92 0.92 0.92 0.91
increased 40%.
Table 26 BOND STRENGTH DESIGN INFORMATION FOR FRACTIONAL REINFORCING BARS IN HOLES
Bar size
#3 #4 #5 #6 #7 #8 #9 #10
Characteristic bond psi 1,740 1,703 1,553 1,441 1,356 1,282 1,226 1,169
Temperature
k,uncr
(N/mm2)
range A3
strength and minimum (12.0) (11.7) (10.7) (9.9) (9.4) (8.8) (8.4) (8.1)
(mm) (62) (71) (80) (87) (94) (102) (114) (127)
Temperature
k,uncr
range B3
(mm) (40) (51) (64) (76) (89) (102) (114) (127)
Dry concrete fd - 0.65 0.65 0.55 0.55 0.55 0.45 0.45 0.45
Permissible
installation
conditions
Water-saturated fws - 0.65 0.55 0.55 0.55 0.45 0.45 0.45 0.45
concrete kws - 1.00 1.00 1.00 1.00 1.00 0.95 0.91 0.88
1 Bond strength values correspond to concrete compressive strength range 2,500 psi fc 4,500 psi. For 4,500 psi fc 6,500 psi, tabulated characteristic bond
strength may be increased by 6%. For 6,500 psi fc 8,000 psi, tabulated characteristic bond strength may be increased by 10%.
2 Characteristic bond strengths are for sustained loads including dead and live loads. For short-term loads including wind and seismic, bond strengths may be increased
40%.

Table 27 STEEL DESIGN INFORMATION FOR EU METRIC REINFORCING BARS1
Bar size
8 10 12 14 16 20 25 28 32
mm 8.0 10.0 12.0 14.0 16.0 20.0 25.0 28.0 32.0
(in.) (0.315) (0.394) (0.472) (0.551) (0.630) (0.787) (0.984) (1.102) (1.260)
Bar effective cross-sectional mm2 50.3 78.5 113.1 153.9 201.1 314.2 490.9 615.8 804.2
Ase
area (in.2) (0.078) (0.122) (0.175) (0.239) (0.312) (0.487) (0.761) (0.954) (1.247)
kN 27.6 43.2 62.2 84.7 110.6 172.8 270.0 338.7 442.3
Nominal strength Nsa
(lb) (6,215) (9,711) (13,984) (19,034) (24,860) (38,844) (60,694) (76,135) (99,441)
as governed
DIN 488 BSt 550/500
by steel strength kN 16.6 25.9 37.3 50.8 66.4 103.7 162.0 203.2 265.4
Vsa
(lb) (3,729) (5,827) (8,390) (11,420) (14,916) (23,307) (36,416) (45,681) (59,665)
Strength reduction
f - 0.65
factor f for tension2
Strength reduction
f - 0.60
factor f for shear2
Table 28 CONCRETE BREAKOUT DESIGN INFORMATION FOR EU METRIC REINFORCING BARS IN HOLES
Bar size
8 10 12 14 16 20 25 28 32
Effectiveness factor SI 7.1
kc,cr
for cracked concrete (in-lb) (17)
Effectiveness factor SI 10
kc,uncr
for un-cracked concrete (in-lb) (24)
mm 40 50 60 70 80 100 125 140 160
(in.) (1.6) (2) (2.4) (2.8) (3.1) (3.9) (4.9) (5.5) (6.3)
mm 40 50 60 70 80 100 125 140 160
(in.) (1.6) (2) (2.4) (2.8) (3.1) (3.9) (4.9) (5.5) (6.3)
Minimum member mm hef+ 30
hmin hef + 2d o
thickness (in.) (hef + 1-1/4)
tension, concrete failure f - 0.65
modes, Condition B2
shear, concrete failure modes, f - 0.70
Condition B2

Table 29 BOND STRENGTH DESIGN INFORMATION FOR EU METRIC REINFORCING BARS IN HOLES DRILLED
WITH A HAMMER DRILL AND CARBIDE BIT1,4
Bar size
8 10 12 14 16 20 25 28 32
Characteristic bond N/mm2 7.5 7.5 7.5 7.4 7.2 6.7 5.9 5.6 5.0
k,cr
strength and minimum (psi) (1,092) (1,092) (1,092) (1,068) (1,044) (972) (862) (806) (732)
anchor embedment in mm 57 63 69 75 80 89 100 112 128

(in.) (2.23) (2.49) (2.73) (2.95) (3.15) (3.52) (3.94) (4.41) (5.04)
k,uncr
strength and minimum (psi) (2,264) (2,264) (2,264) (2,198) (2,142) (2,039) (1,955) (1,908) (1,862)
(in.) (2.23) (2.49) (2.73) (2.95) (3.15) (3.52) (3.94) (4.41) (5.04)
k,cr
strength and minimum (psi) (444) (444) (444) (410) (379) (336) (298) (278) (260)

(in.) (1.57) (1.80) (2.10) (2.37) (2.62) (3.15) (3.94) (4.41) (5.04)
k,uncr
(in.) (1.57) (1.80) (2.10) (2.37) (2.62) (3.15) (3.94) (4.41) (5.04)
Dry concrete fd - 0.65 0.65 0.65 0.65 0.65 0.55 0.55 0.55 0.55
fws
Water-saturated - 0.55 0.55 0.55 0.45 0.45 0.45 0.45 0.45 0.45
concrete kws - 1.00 1.00 1.00 1.00 1.00 1.00 0.97 0.94 0.94
conditions
fwf - 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45
Water-filled hole
kwf - 1.00 1.00 1.00 0.96 0.93 0.87 0.82 0.79 0.79
Underwater fuw - 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45
application kuw - 0.95 0.95 0.94 0.94 0.93 0.92 0.92 0.91 0.91

Table 30 BOND STRENGTH DESIGN INFORMATION FOR EU METRIC REINFORCING BARS IN HOLES DRILLED
WITH A CORE DRILL1,4
Bar size
8 10 12 14 16 20 25 28 32
N/mm2 12.0 12.0 12.0 11.3 10.7 9.7 8.9 8.5 8.1
Temperature
Characteristic bond k,uncr

range A3
strength and minimum (psi) (1,740) (1,740) (1,740) (1,637) (1,553) (1,413) (1,291) (1,235) (1,169)
(in.) (2.19) (2.49) (2.73) (2.95) (3.15) (3.52) (3.94) (4.41) (5.04)
N/mm2 4.1 4.1 4.1 3.9 3.7 3.4 3.1 2.9 2.8
Temperature

range B3
anchor embedment mm 40 41 48 56 64 80 100 112 128
in un-cracked concrete2 hef,min (in.) (1.57) (1.61) (1.89) (2.20) (2.52) (3.15) (3.94) (4.41) (5.04)
Dry concrete fd - 0.65 0.65 0.65 0.55 0.55 0.55 0.45 0.45 0.45
Permissible
installation
conditions
Water-saturated fws - 0.55 0.55 0.55 0.45 0.45 0.45 0.45 0.45 0.45
concrete kws - 1.0 1.0 1.0 1.0 1.0 1.0 0.92 0.88 0.88
Table 31 STEEL DESIGN INFORMATION FOR CANADIAN METRIC REINFORCING BARS1
Bar size
10 M 15 M 20 M 25 M 30 M
mm 11.3 16.0 19.5 25.2 29.9
(in.) (0.445) (0.630) (0.768) (0.992) (1.177)
Bar effective cross-sectional mm2 100.3 201.1 298.6 498.8 702.2
Ase
area (in.2) (0.155) (0.312) (0.463) (0.773) (1.088)
kN 54.2 108.6 161.3 269.3 379.2
Nominal strength Nsa
(lb) (12,175) (24,408) (36,255) (60,548) (85,239)
as governed by
steel strength kN 32.5 65.1 96.8 161.6 227.5
Vsa
(lb) (7,305) (14,645) (21,753) (36,329) (51,144)
CSA G30
Reduction for seismic

aV,seis - 0.70
shear
Strength reduction
f - 0.65
factor f for tension2
Strength reduction
f - 0.60
factor f for shear2

Table 32 CONCRETE BREAKOUT DESIGN INFORMATION FOR CANADIAN METRIC REINFORCING BARS IN HOLES
Bar size
10 M 15 M 20 M 25 M 30 M
Effectiveness factor for SI 7.1
kc,cr
cracked concrete (in-lb) (17)
Effectiveness factor for SI 10
kc,uncr
un-cracked concrete (in-lb) (24)
mm 57 80 98 126 150
(in.) (2.2) (3.1) (3.8) (5.0) (5.9)
mm 57 80 98 126 150
(in.) (2.2) (3.1) (3.8) (5.0) (5.9)
mm hef + 30
(in.) (hef + 1-1/4)
Critical edge distance
splitting (for un-cracked concrete)
for tension, concrete failure f - 0.65
modes, Condition B2
for shear, concrete failure f - 0.70
modes, Condition B2

Table 33 BOND STRENGTH DESIGN INFORMATION FOR CANADIAN METRIC REINFORCING BARS IN HOLES
DRILLED WITH A HAMMER DRILL AND CARBIDE BIT1,4
Bar size
10 M 15 M 20 M 25 M 30 M
Characteristic bond N/mm2 7.5 7.2 6.8 5.9 5.4

k,cr
strength and minimum (psi) (1,092) (1,044) (991) (852) (777)
anchor embedment in mm 67 80 88 101 120

(in.) (2.65) (3.15) (3.48) (3.97) (4.71)

k,uncr
strength and minimum (psi) (2,264) (2,142) (2,058) (1,955) (1,880)
(in.) (2.65) (3.15) (3.48) (3.97) (4.71)

k,cr
strength and minimum (psi) (444) (379) (342) (294) (271)

(in.) (2.00) (2.62) (3.07) (3.97) (4.71)

k,uncr
(in.) (2.00) (2.62) (3.07) (3.97) (4.71)
Dry concrete fd - 0.65 0.65 0.65 0.55 0.55
fws
Water-saturated - 0.55 0.45 0.45 0.45 0.45

concrete kws - 1.0 1.0 1.0 1.0 0.96
conditions
fwf - 0.45 0.45 0.45 0.45 0.45

Water-filled hole
kwf - 1.00 0.96 0.91 0.85 0.81
Underwater fuw - 0.45 0.45 0.45 0.45 0.45
application kuw - 0.95 0.94 0.93 0.92 0.91

Table 34 BOND STRENGTH DESIGN INFORMATION FOR CANADIAN METRIC REINFORCING BARS IN HOLES
Bar size
10 M 15 M 20 M 25 M 30 M
N/mm2 12.0 10.7 9.9 8.9 8.3
Temperature

range A3
strength and minimum (psi) (1,740) (1,553) (1,431) (1,291) (1,197)

anchor embedment mm 67 80 88 101 120
in un-cracked concrete hef,min
(in.) (2.65) (3.15) (3.48) (3.97) (4.71)
N/mm2 4.1 3.7 3.4 3.1 2.8
Temperature

range B3

anchor embedment mm 45 64 78 101 120
in un-cracked concrete hef,min
(in.) (1.78) (2.52) (3.07) (3.97) (4.71)
Dry concrete fd - 0.65 0.55 0.55 0.45 0.45
Permissible
installation
conditions
Water-saturated fws - 0.55 0.45 0.45 0.45 0.45

concrete kws - 1.00 1.00 1.00 0.96 0.90
Installation Instructions
Adhesive anchoring system for fastenings in normal Method 2 for water filled boreholes, submerged concrete
weight concrete or diamond cored boreholes:
Prior to use of product follow instructions for use and Flush hole 2 times by inserting a water hose (water-line
pressure) to the back of the borehole until water runs clear.
recommended safety precautions.
Brush 2 times with the specified brush size (brush =
Check expiration date: See expiration date imprint on
borehole ) by inserting the round steel brush to the back of
foilpack manifold. (Month/Year). Do not use expired product. the borehole with a twisting motion and removing it. The
Foil pack temperature: Must be between 41F and 104F brush should resist insertion into the borehole if not, the
(5C - 40C) when in use. brush is too small and must be replaced with the proper brush
Base material temperature at time of installation: Must be diameter.
between 41F and 110F (5C - 43C). Flush again 2 times until water runs clear.
Instructions for transport and storage: Keep in a cool, dry Important! For diamond cored boreholes and if a dry
and dark place between 41F and 77F (5C - 25C). borehole is required for injection (e.g. water flows into
cleaned borehole), continue with borehole cleaning as
Material Safety Data Sheet: Review the MSDS before use.
described by methode 1. Remove all standing water
Installation Instructions: Follow the pictograms 1-14 for the completely (i.e. vacuum, compressed air or other appropriate
sequence of operations and refer to tables 1-3 for setting details. For procedure). To attain a dried borehole, a Hilti HIT-DL air nozzle
any application not covered by this document (e.g. h ef beyond attachment is recommended for borehole depth up to 10 inch
values specified in setting details), contact Hilti. (250 mm) and required for borehole depth > 10 inch (250 mm).
Installation flow Chart The borehole must be free of dust, debris, ice, oil, grease
Hammer Drilling Diamond Coring Hammer Drilling and other contaminants prior to adhesive injection.
Check Water Water
Inadequate borehole cleaning = poor load values
borehole Dry saturated Dry saturated Water-filled Submerged
conditions 5. Insert foil pack in foil pack holder. Never use damaged foil
Borehole packs and/or damaged or unclean foil pack holders.
Cleaning Cleaning Cleaning
Cleaning method 1 method 2+1 method 2
instructions 6. Tightly attach Hilti HIT-RE-M mixer to foil pack manifold.
Borehole
Attach new mixer prior to dispensing a new foil pack (snug fit).
Clean and dry Clean and water-filled
conditions Do not modify the mixer in any way. Make sure the mixing
element is in the mixer. Use only the mixer supplied with the
Installation Horizontal All
direction and vertical
Overhead directions adhesive.
7. Insert foil pack holder with foil pack into HIT-dispenser.
Drilling ? 10 inch > 10 inch All drilling All drilling Push release trigger, retract plunger and insert foil pack holder
depth (250 mm) (250 mm) depth depth
into the appropriate Hilti dispenser.
Injection HIT-SZ/IP HIT-SZ/IP HIT-SZ/IP HIT-SZ/IP 8. Discard initial adhesive. The foil pack opens automatically as
instructions not required recommended required required
dispensing is initiated. Depending on the size of the foil pack an
1. Drill hole normal to the surface with a hammer drill set in initial amount of adhesive has to be discarded. See pictogram 8
rotation-hammer mode using an appropriately sized carbide for discard quantities. If a new mixer is installed onto a
drill bit, or with a core rig and an appropriately sized diamond previously-opened foil pack, the first trigger pulls must also be
core bit, to the required embedment depth. See tables discarded as described above. For each new foil pack a new
describing setting details. (Drill bits must conform to ANSI mixer must be used.
B212-1994.) 9-10. Inject adhesive from the back of the borehole without
2-4. Clean hole: Cleaning method has to be decided based on forming air voids:
drilling method and borehole conditions (see flow chart above). Verify if borehole conditions have changed (e.g. water in the
Just before setting an anchor/rebar, the borehole must be free borehole) after cleaning. If yes, repeat cleaning according
of dust and debris by one of the following methods: points 2 - 4.
Method 1 for dry or water saturated concrete (refer to Inject the adhesive starting at the back of the borehole (use
pictograms): the extension for deep boreholes), slowly withdraw the mixer
Blow from the back of the borehole with oil-free compressed with each trigger pull. Fill holes approximately 2/3 full, or as
air (min. 90psi at 3.5 CFM (6 bar at 6 m3/h)) fully retracting the required to ensure that the annular gap between the anchor/
air extension 2 times until return air stream is free of rebar and the concrete is completely filled with adhesive
noticeable dust. along the embedment length. After injection is completed,
depressurize the dispenser by pressing the release trigger.
Brush 2 times with the specified brush size (brush =
This will prevent further adhesive discharge from the mixer.
borehole ) by inserting the round steel brush to the back of
the borehole in a twisting motion and removing it. The brush Piston plug injection HIT-SZ/IP recommended for
should resist insertion into the borehole if not, the brush is borehole depth > 10 inch/250 mm. Waterfilled boreholes
too small and must be replaced with the proper brush or submerged concrete, and overhead installation the
diameter. piston plugs are required. Assemble HIT-RE-M mixer,
extension(s) and appropriately sized piston plug HIT-SZ/IP.
Blow again with compressed air 2 times until return air stream
Insert piston plug to back of the borehole and inject adhesive
is free of noticeable dust.
as described in the injection method
above. During injection the piston
plug will be naturally extruded out of or
the borehole by the adhesive
pressure.
11. Insert anchor/rebar into borehole.
Mark and set anchor/rebar to the
required embedment depth. Before
use, verify that the anchor/rebar is dry
and free of oil and other contaminants.
To ease installation, anchor/rebar may
be slowly twisted as they are inserted.
After installing an anchor/rebar, the
annular gap must be completely filled
with adhesive. If the borehole is not
completely filled along the embedment
depth the installation should be
rejected. Hilti should be contacted for
further information.
Attention! For overhead applications
take special care when inserting the
anchor/rebar. Excess adhesive will be
forced out of the borehole take
appropriate steps to prevent it from
falling onto the installer. Position the
anchor/rebar and secure it from
moving/falling during the curing time
(e.g. wedges). Observe the gel time t
gel, which varies according to
temperature of base material. Minor or
adjustments to the anchor/rebar
position may be performed during the
gel time. See table.
12. Do not disturb the anchor/rebar
once the gel time t gel has elapsed
until t cure, ini has passed.
13. Preparation work may continue for
rebar applications. Between t cure,
ini and t cure, full the adhesive has
a limited load bearing capacity, do not
apply a torque or load on the
anchor/rebar during this time.
14. Apply load/torque after t cure, full
has passed, and the fixture to be
attached has been positioned.
Partly used foil packs must be used up
within four weeks. Leave the mixer attached
to the foil pack manifold and store under the
recommended storage conditions. If reused, F C twork / tgel tcure, ini tcure, full Time
attach a new mixer and discard theinitial
41 5 2.5 hrs 18 hrs 72 hrs
quantity of anchor adhesive as described by
point 8. 50 10 2 hrs 12 hrs 48 hrs
59 15 1.5 hrs 8 hrs 24 hrs
68 20 30 min 6 hrs 12 hrs
86 30 20 min 4 hrs 8 hrs
104 40 12 min 2 hrs 4 hrs
Table 1 Setting Details of Hilti HIT-RE 500-SD with threaded rod
d do hef min-max inst df hmin

[inch] [mm] [inch] [inch] [mm] [ft-lb] [Nm] [inch] [inch]
3/8 9.5 7/16 1-1/2 7 1/2 40 191 15 20 7/16 hef + 1-1/4
1/2 12.7 9/16 2 10 51 254 30 41 9/16 (30 mm)
5/8 15.9 3/4 2-1/2 12-1/2 64 318 60 81 11/16

3/4 19.1 7/8 3 15 76 381 100 136 13/16
7/8 22.2 1 3-1/2 17-1/2 89 445 125 169 15/16 hef + 2 d0
1 25.4 1-1/8 4 20 102 508 150 203 1-1/8
1-1/4 31.8 1-3/8 5 25 127 635 200 271 1-3/8
[mm] [mm] [Nm] [mm] [mm]
M8 10 40 160 10 9
M10 12 41 200 20 12 hef + 30
M12 14 48 240 40 14
M16 18 64 320 80 18
M20 24 80 400 150 22
M24 28 96 480 200 26 hef + 2 d0
M27 30 108 540 270 30
M30 35 120 600 300 33
Table 2 Setting Details of Hilti HIT-RE 500-SD with HIS-N and HIS-RN Inserts
d do hef inst df hmin

[inch] [mm] [inch] [inch] [mm] [ft-lb] [Nm] [inch] [inch] [mm]
3/8 9.5 11/16 4 3/8 110 15 20 7/16 5-3/4 150
1/2 12.7 7/8 5 125 30 41 9/16 6-3/4 170
5/8 15.9 1-1/8 6 3/4 170 60 81 11/16 9 230
3/4 19.1 1-1/4 8-1/8 205 100 136 13/16 10-3/4 270
[mm] [mm] [mm] [Nm] [mm] [mm]
M8 14 90 10 9 120
M10 18 110 20 12 150
M12 22 125 40 14 170
M16 28 170 80 18 230
M20 32 205 150 22 270
Table 3 Setting Details of Hilti HIT-RE 500-SD with reinforcement bars
d do hef min-max hmin

US rebar [inch] [inch] [mm] [inch]
#3 1/2 1-1/2 7-1/2 40 191
h + 1-1/4 (30 mm)
ef
#4 5/8 2 10 51 254
#5 3/4 2-1/2 12-1/2 64 318
#6 7/8 3 15 76 381
#7 1 3-1/2 17-1/2 89 445 hef + 2 d0
#8 1-1/8 4 20 102 508
#9 1-3/8 4-1/2 22-1/2 114 572
# 10 1-1/2 5 25 127 635
Rebar [mm] [mm] [mm] [mm]
8 12 40 160
h + 30
ef
10 14 41 200
12 16 48 240
14 18 56 280
16 20 64 320
20 25 80 400 hef + 2 d0
25 32 100 500
28 35 112 560
32 40 128 640
CA rebar [inch] [mm] [inch]
10 M 9/16 45 226 hef + 1-1/4 (30 mm)
15 M 3/4 64 320
20 M 1 78 390
h +2d
ef 0
25 M 1-1/4 101 504
30 M 1-1/2 120 598
Material Safety Data Sheet
MSDS No.: 318

Revision No.: 000
Revision Date: 04/12/07
Page: 1 of 2
Product name: HITRE 500 SD

Description: High strength epoxy adhesive for anchoring in concrete and rebar doweling. Part A is the large
tube; Part B is the small tube.
Supplier: Hilti, Inc. P.O. Box 21148, Tulsa, OK 74121
Emergency # (Chem-Trec.): 1 800 424 9300 (USA, PR, Virgin Islands, Canada); 703 527 3887 (Other countries)
INGREDIENTS AND EXPOSURE LIMITS
Ingredients: CAS Number: TLV: PEL: STEL:
Part A: Bisphenol A epoxy resin 25068-38-6 NE NE NE
Bisphenol F epoxy resin 28064-14-4 NE NE NE
Quartz sand 14808-60-7 0.025 mg/m3 (R) 10 mg/m3 % SiO2 + 2 NE
Alkylglycidyl ether 19136100-5012 * NE NE NE
Diglycidyl ether 19136100-5013 * NE NE NE
Siloxanes & silicones 67762-90-7 NE NE NE
Part B: m-xylene diamine 01477-55-0 C: 0.1 / S C: 0.1 / S NE
Aliphatic polyamine 19136100-5014 * NE NE NE
Quartz sand 14808-60-7 0.025 mg/m3 (R) 10 mg/m3 % SiO2 + 2 NE
Aluminum oxide 01344-28-1 10 mg/m3 15 mg/m3 (T) NE
Cement 65997-16-2 NE NE NE
Siloxanes & silicones 67762-90-7 NE NE NE
Abbreviations: * = indicates New Jersey Trade Secret Registry Number. C = Ceiling. NE = None Established.
R =dust respirable fraction. S = Skin exposure, including the mucous membranes, eyes, and skin.
T = total dust. TLV = ACGIH Threshold Limit Values. PEL = OSHA Permissible Exposure Limits.
STEL = ACGIH/OSHA Short Term Exposure Limit
PHYSICAL DATA
Appearance: A: Gray; B: red / paste. VOC Content: 0.0 g/l
Amine-like odor.
Boiling Point: Approx. 212 F Vapor Pressure: Not determined.
Vapor Density: (air = 1) Not determined. Odor Threshold: Not determined.
Evaporation Rate: Not applicable. Solubility in Water: Insoluble.
Specific Gravity: 1.5 pH: 11 (Part B with 1:1 water)
FIRE AND EXPLOSION HAZARD DATA
Flash Point: > 200 F Flammable Limits: Not applicable.
Extinguishing Media: Water, CO2, Dry Chemical, Foam.
Special Fire Fighting A NIOSH-approved self-contained breathing apparatus (SCBA) should be worn when
Procedures: fighting fires involving chemicals.
Unusual Fire and Explosion Hazards: None known. Product serves as a fire stopping material.
REACTIVITY DATA
Flash Point: > 200 F Flammable Limits: Not applicable.
Extinguishing Media: CO2, Dry Chemical, Foam, Water Spray.
Special Fire Fighting Procedures: A self-contained breathing apparatus should be worn when fighting fires involving chemicals.
Unusual Fire and Explosion Hazards: None known. Thermal decomposition products can be formed including Hazards: COX,
NOX, water and carbon.
Material Safety Data Sheet
MSDS No.: 318

Revision No.: 000
Revision Date: 04/12/07
Page: 2 of 2
HEALTH HAZARD DATA

Known Hazards: Part A: Eye and skin irritation. Possible skin sensitizer. Part B: Corrosive
Signs and Symptoms of Exposure: Part A: an be irritating to the eyes and skin, Can cause skin sensitization with some
individuals (itching, redness, swelling). Part B: Can cause eye and skin burns. Vapors
can be irritating. If swallowed, can cause burns.
Routes of Exposure: Contact. Inhalation.
Carcinogenicity: IARC classifies crystalline silica (quartz sand) as a Group I carcinogen based upon
evidence among workers in industries where there has been long-term and chronic
exposure (via inhalation) to silica dust; e.g. mining, quarry, stone crushing, refractory brick
and pottery workers. This product does not pose a dust hazard; therefore, this
classification is not relevant.
Medical Conditions Aggravated Eye, skin, and respiratory conditions.
by Exposure:
EMERGENCY AND FIRST AID PROCEDURES

Eyes: Flush immediately with water for at least 15 minutes. Contact a Physician if symptoms
occur.
Skin: Wash immediately with soap and water. Launder contaminated clothing before reuse.
Seek medical attention if any symptoms occur.
Inhalation: If symptoms occur, move to fresh air. Call a physician if symptoms persist.
Ingestion: Do not induce vomiting unless directed by a physician. Contact a Physician immediately.
Other: Referral to a physician is recommended if there is any question about the seriousness of
the injury/exposure
CONTROL MEASURES AND PERSONAL PROTECTIVE EQUIPMENT
Ventilation: General (natural or mechanically induced fresh air movements).
Eye Protection: Safety glasses with side shields recommended.
Skin Protection: Impermeable (neoprene or rubber) gloves recommended.
Respiratory Protection: None normally required. Where ventilation is inadequate to control vapors, use a NIOSH-
approved respirator with organic vapor cartridges.
PRECAUTIONS FOR SAFE HANDLING AND USE
Handling and Storing Precautions: For industrial use only. Keep away from children. Use with adequate ventilation. Avoid
contact with the eyes or skin. Practice good hygiene; i.e. wash after using and before
eating or smoking. Store in a cool dry area between 41 and 77 F (5 - 25 C). Keep from
freezing.
Spill Procedures: Take up with an absorbent material and place in a container for proper disposal.
REGULATORY INFORMATION
Hazard Communication: This MSDS has been prepared in accordance with the federal OSHA Hazard
Communication Standard 29 CFR 1910.1200.
HMIS Codes: Health 3, Flammability 1, Reactivity 0, PPE B
DOT Shipping Name: Consumer commodity, ORM-D
IATA / ICAO Shipping Name: Amines, solid, corrosive, n.o.s. (M-xylenediamine), Class 8, UN3259, PG II
TSCA Inventory Status: Chemical components listed on TSCA inventory. SARA Title III, Section 313: This product
does not contain any toxic chemicals which are subject to reporting under Section 313 of
SARA Title III (40 CFR Part 372).
EPA Waste Code(s): Not regulated by EPA as a hazardous waste
Waste Disposal Methods: Consult with regulatory agencies or your corporate personnel for disposal methods that
comply with local, state, and federal safety, health and environmental regulations.
CONTACTS
Customer Service: 1 800 879 8000 Technical Service: 1 800 879 8000
Health / Safety: 1 800 879 6000 Jerry Metcalf (x6704)
Emergency # (Chem-Trec): 1 800 424 9300 (USA, PR, Virgin Islands, Canada); 001 703 527 3887 (other countries)
The information and recommendations contained herein are based upon data believed to be correct; however, no guarantee or
warranty of any kind expressed or implied is made with respect to the information provided.
In the US: In Canada:
P.O. Box 21148 Tulsa, OK 74121 6790 Century Avenue, Suite 300
Customer Service: 1-800-879-8000 CDN-Mississauga, Ontario L5N 2V8
en espaol: 1-800-879-5000 Customer Service: 1-800-363-4458
Fax: 1-800-879-7000 Fax: 1-800-363-4459
www.us.hilti.com www.hilti.ca
Hilti is an equal opportunity employer.

Hilti is a registered trademark of Hilti, Corp.
Copyright 2007 by Hilti, Inc. (U.S.)
H454 3428243 08/07 DBS
*14001 US only
The data contained in this literature was current as of the date of publication. Updates and changes may be made
based on later testing. If verification is needed that the data is still current, please contact the Hilti Technical Support
Specialists at 1-800-879-8000. All published load values contained in this literature represent the results of testing by
Hilti or test organizations. Local base materials were used. Because of variations in materials, on-site testing is
necessary to determine performance at any specific site. Laser beams represented by red lines in this publication.
Printed in the United States

Re 500-SD PDF

Uploaded by

Copyright:

Available Formats

Re 500-SD PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Re 500-SD PDF

Uploaded by

Copyright:

Available Formats

HIT-RE 500-SD

Code compliance with

Building Code Compliance

Technical Support and Training

PROFIS Anchor Design software performs strength design calculations right

HIT-RE 500-SD Epoxy Adhesive Anchor System Technical Data

Gel/Full Cure Time Table (Approximate)

Manual MD 2500 Manual Dispenser

Hole Cleaning/Injection Accessories

HIT-RE 500-SD Epoxy Adhesive Anchor

Material Specifications for HIT-RE 500-SD Cured Adhesive

Bond Strength ASTM C882-911

HIT-RE 500-SD Epoxy Adhesive Anchor

HIT-RE 500-SD Epoxy Adhesive Anchor

(D-14s) Where applicable, the modified bond

HIT-RE 500-SD Epoxy Adhesive Anchor

Threaded rod Hilti HIS internally Deformed reinforcement

Bond strength design flowchart

Cracked Concrete Un-cracked Concrete

Hammer Drilled Hammer Drilled Diamond Cored

Dry Water Dry Water Water Under Dry Water

(WS) (WS) (WF) (UW) (WS)

fD fWS fD fWS fWF fUW fD fWS

k,cr k,uncr k,uncr

HIT-RE 500-SD Epoxy Adhesive Anchor

Table 2 TENSILE PROPERTIES OF COMMON CARBON STEEL THREADED ROD MATERIALS1

Table 3 TENSILE PROPERTIES OF COMMON STAINLESS STEEL THREADED ROD MATERIALS1

HIT-RE 500-SD Epoxy Adhesive Anchor

Minimum specified Minimum specified yield

Table 6 TENSILE PROPERTIES OF COMMON REINFORCING BARS

HIT-RE 500-SD Epoxy Adhesive Anchor

Nominal rod diameter (in.)

Nominal strength as governed

by steel strength lb 4,844 10,642 16,950 25,087 34,627 45,426 72,681

HIT-RE 500-SD Epoxy Adhesive Anchor

Nominal rod diameter (in.)

HIT-RE 500-SD Epoxy Adhesive Anchor

Nominal rod diameter (in.)

minimum anchor embedment in

minimum anchor embedment

Dry concrete fd - 0.65 0.65 0.65 0.65 0.55 0.55 0.55

HIT-RE 500-SD Epoxy Adhesive Anchor

Nominal rod diameter (in.)

Characteristic bond strength and k,uncr

(N/mm2) (12.0) (11.7) (10.7) (9.9) (9.4) (8.8) (8.1)

Characteristic bond strength and k,uncr

(N/mm2) (4.1) (4.1) (3.7) (3.4) (3.2) (3.1) (2.8)

fws - 0.55 0.55 0.45 0.45 0.45 0.45 0.45

HIT-RE 500-SD Epoxy Adhesive Anchor

Table 11 STEEL DESIGN INFORMATION FOR METRIC THREADED ROD1

Nominal rod diameter (mm)

kN 25.6 40.6 59.0 109.9 171.5 247.1 229.5 280.5

HIT-RE 500-SD Epoxy Adhesive Anchor

Nominal rod diameter (mm)

HIT-RE 500-SD Epoxy Adhesive Anchor

Nominal rod diameter (mm)

minimum anchor embedment

minimum anchor embedment

fwf - 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45