DESIGN OF FLOOR SLAB

Design Data
Dimensions of the slab (c/c distance b/w supports), fck = 25 N/mm2
Length of short span, Lx = 4 m fy = 415 N/mm2
Length of long span, Ly = 4 m
Width of the supporting beam, = 230 mm
Clear cover to main reinforcement = 20 mm
Assume dia. of reinforcement steel = 8 mm

Calculations
Assume the thickness of slab as 150 mm ; Effective depth, d = 126 mm
Effective span, lx = 4 m (or) 3.896 m whichever is less; d = 3.896 m
ly = 4 m (or) 3.896 m whichever is less; d = 3.896 m
(ly / lx) = 1.00 < 2 ; Here, (ly / lx) is less than 2, Hence design the slab as two way slab

Load Calculations
Dead Load of slab = 0.15 x 25 = 3.75 KN/m2 Dust Load on slab = 0 KN/m2
Finishes load on slab = 1.50 KN/m2 Other load on slab = 0 KN/m2
Live Load on slab = 5.0 KN/m 2

Total Dead load acting on the Structure = 5.25 KN/m2

Total live load acting on the Structure = 5.0 KN/m2
Factored Design Load w = 15.38 KN/m2

Support Condition (Type of panel according to support condition)

Two Long Edges Discontinuous For this support condition,
Short span coefficient for (ly / lx) = 1, Long span coefficient,
For negative moment, ax = 0.0000 For negative moment, ay = 0.045
For positive moment, ax = 0.0350 For positive moment, ay = 0.035

Moment Calculation
Max. BM per unit width, Mx = ax w lx2 & My = ay w lx2

Mu Mu / bd2 pt Ast, req Ast , min = (0.12/100) bD = 180 mm2

KNm N/mm2 % mm2
For Short Span,
Reinforcement details
At mid span, 8.17 0.51 0.1448 182
At supports, 0.00 0.00 0 0 Provide Y 10 @ 150 mm c/c at midspan &
For Long span, supports for short span (Ast pro. = 524 mm2 )
At mid span, 8.17 0.59 0.1682 212 Provide Y 10 @ 150 mm c/c at midspan &
At supports, 10.51 0.75 0.2155 272 supports for long span (Ast pro. = 524 mm2 )

Check for Deflection

Percentage of tension reinforcement = 0.42 %
fs = 0.58 fy (Ast req / Ast pro
) = 83.7
Refer Fig. 4 of IS 456,
Modification factor = 2
Allowable (Span / deff ) ratio = 52
Effective depth required = 75 mm
< d prov.
Hence OK
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 2 3 4 5 6 7 8 9 10 11
Short Span Coefficients (a x)

One Short Edge One Long Edge Two Adjacent Edges Two Short Edges
Interior Panels
Discontinuous Discontinuous Discontinuous Discontinuous

S.No. Values of ( ly / lx ) Negative Negative Negative Negative Negative

Positive Positive Positive Positive Positive
moment at moment at moment at moment at moment at
moment at moment at moment at moment at moment at
continuous continuous continuous continuous continuous
midspan midspan midspan midspan midspan
edge edge edge edge edge

1 1.00 0.0320 0.0240 0.0370 0.0280 0.0370 0.0280 0.0470 0.0350 0.0450 0.0350

2 1.01 0.0325 0.0244 0.0376 0.0284 0.0377 0.0285 0.0476 0.0355 0.0454 0.0352

3 1.02 0.0330 0.0248 0.0382 0.0288 0.0384 0.0290 0.0482 0.0360 0.0458 0.0354

4 1.03 0.0335 0.0252 0.0388 0.0292 0.0391 0.0295 0.0488 0.0365 0.0462 0.0356

5 1.04 0.0340 0.0256 0.0394 0.0296 0.0398 0.0300 0.0494 0.0370 0.0466 0.0358

6 1.05 0.0345 0.0260 0.0400 0.0300 0.0405 0.0305 0.0500 0.0375 0.0470 0.0360

7 1.06 0.0350 0.0264 0.0406 0.0304 0.0412 0.0310 0.0506 0.0380 0.0474 0.0362

8 1.07 0.0355 0.0268 0.0412 0.0308 0.0419 0.0315 0.0512 0.0385 0.0478 0.0364

9 1.08 0.0360 0.0272 0.0418 0.0312 0.0426 0.0320 0.0518 0.0390 0.0482 0.0366

10 1.09 0.0365 0.0276 0.0424 0.0316 0.0433 0.0325 0.0524 0.0395 0.0486 0.0368

11 1.10 0.0370 0.0280 0.0430 0.0320 0.0440 0.0330 0.0530 0.0400 0.0490 0.0370

12 1.11 0.0376 0.0284 0.0435 0.0324 0.0448 0.0336 0.0537 0.0405 0.0493 0.0373
13 1.12 0.0382 0.0288 0.0440 0.0328 0.0456 0.0342 0.0544 0.0410 0.0496 0.0376
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 2 3 4 5 6 7 8 9 10 11
Short Span Coefficients (a x)

One Short Edge One Long Edge Two Adjacent Edges Two Short Edges
Interior Panels
Discontinuous Discontinuous Discontinuous Discontinuous

S.No. Values of ( ly / lx ) Negative Negative Negative Negative Negative

Positive Positive Positive Positive Positive
moment at moment at moment at moment at moment at
moment at moment at moment at moment at moment at
continuous continuous continuous continuous continuous
midspan midspan midspan midspan midspan
edge edge edge edge edge

14 1.13 0.0388 0.0292 0.0445 0.0332 0.0464 0.0348 0.0551 0.0415 0.0499 0.0379

15 1.14 0.0394 0.0296 0.0450 0.0336 0.0472 0.0354 0.0558 0.0420 0.0502 0.0382

16 1.15 0.0400 0.0300 0.0455 0.0340 0.0480 0.0360 0.0565 0.0425 0.0505 0.0385

17 1.16 0.0406 0.0304 0.0460 0.0344 0.0488 0.0366 0.0572 0.0430 0.0508 0.0388

18 1.17 0.0412 0.0308 0.0465 0.0348 0.0496 0.0372 0.0579 0.0435 0.0511 0.0391

19 1.18 0.0418 0.0312 0.0470 0.0352 0.0504 0.0378 0.0586 0.0440 0.0514 0.0394

20 1.19 0.0424 0.0316 0.0475 0.0356 0.0512 0.0384 0.0593 0.0445 0.0517 0.0397

21 1.20 0.0430 0.0320 0.0480 0.0360 0.0520 0.0390 0.0600 0.0450 0.0520 0.0400

22 1.21 0.0434 0.0324 0.0483 0.0363 0.0525 0.0395 0.0605 0.0454 0.0524 0.0403

23 1.22 0.0438 0.0328 0.0486 0.0366 0.0530 0.0400 0.0610 0.0458 0.0528 0.0406

24 1.23 0.0442 0.0332 0.0489 0.0369 0.0535 0.0405 0.0615 0.0462 0.0532 0.0409

25 1.24 0.0446 0.0336 0.0492 0.0372 0.0540 0.0410 0.0620 0.0466 0.0536 0.0412
26 1.25 0.0450 0.0340 0.0495 0.0375 0.0545 0.0415 0.0625 0.0470 0.0540 0.0415
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 2 3 4 5 6 7 8 9 10 11
Short Span Coefficients (a x)

One Short Edge One Long Edge Two Adjacent Edges Two Short Edges
Interior Panels
Discontinuous Discontinuous Discontinuous Discontinuous

S.No. Values of ( ly / lx ) Negative Negative Negative Negative Negative

Positive Positive Positive Positive Positive
moment at moment at moment at moment at moment at
moment at moment at moment at moment at moment at
continuous continuous continuous continuous continuous
midspan midspan midspan midspan midspan
edge edge edge edge edge

27 1.26 0.0454 0.0344 0.0498 0.0378 0.0550 0.0420 0.0630 0.0474 0.0544 0.0418

28 1.27 0.0458 0.0348 0.0501 0.0381 0.0555 0.0425 0.0635 0.0478 0.0548 0.0421

29 1.28 0.0462 0.0352 0.0504 0.0384 0.0560 0.0430 0.0640 0.0482 0.0552 0.0424

30 1.29 0.0466 0.0356 0.0507 0.0387 0.0565 0.0435 0.0645 0.0486 0.0556 0.0427

31 1.30 0.0470 0.0360 0.0510 0.0390 0.0570 0.0440 0.0650 0.0490 0.0560 0.0430

32 1.31 0.0474 0.0363 0.0514 0.0392 0.0576 0.0443 0.0656 0.0494 0.0563 0.0431

33 1.32 0.0478 0.0366 0.0518 0.0394 0.0582 0.0446 0.0662 0.0498 0.0566 0.0432

34 1.33 0.0482 0.0369 0.0522 0.0396 0.0588 0.0449 0.0668 0.0502 0.0569 0.0433

35 1.34 0.0486 0.0372 0.0526 0.0398 0.0594 0.0452 0.0674 0.0506 0.0572 0.0434

36 1.35 0.0490 0.0375 0.0530 0.0400 0.0600 0.0455 0.0680 0.0510 0.0575 0.0435

37 1.36 0.0494 0.0378 0.0534 0.0402 0.0606 0.0458 0.0686 0.0514 0.0578 0.0436

38 1.37 0.0498 0.0381 0.0538 0.0404 0.0612 0.0461 0.0692 0.0518 0.0581 0.0437
39 1.38 0.0502 0.0384 0.0542 0.0406 0.0618 0.0464 0.0698 0.0522 0.0584 0.0438
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 2 3 4 5 6 7 8 9 10 11
Short Span Coefficients (a x)

One Short Edge One Long Edge Two Adjacent Edges Two Short Edges
Interior Panels
Discontinuous Discontinuous Discontinuous Discontinuous

S.No. Values of ( ly / lx ) Negative Negative Negative Negative Negative

Positive Positive Positive Positive Positive
moment at moment at moment at moment at moment at
moment at moment at moment at moment at moment at
continuous continuous continuous continuous continuous
midspan midspan midspan midspan midspan
edge edge edge edge edge

40 1.39 0.0506 0.0387 0.0546 0.0408 0.0624 0.0467 0.0704 0.0526 0.0587 0.0439

41 1.40 0.0510 0.0390 0.0550 0.0410 0.0630 0.0470 0.0710 0.0530 0.0590 0.0440

42 1.41 0.0512 0.0392 0.0552 0.0413 0.0634 0.0474 0.0714 0.0533 0.0591 0.0441

43 1.42 0.0514 0.0394 0.0554 0.0416 0.0638 0.0478 0.0718 0.0536 0.0592 0.0442

44 1.43 0.0516 0.0396 0.0556 0.0419 0.0642 0.0482 0.0722 0.0539 0.0593 0.0443

45 1.44 0.0518 0.0398 0.0558 0.0422 0.0646 0.0486 0.0726 0.0542 0.0594 0.0444

46 1.45 0.0520 0.0400 0.0560 0.0425 0.0650 0.0490 0.0730 0.0545 0.0595 0.0445

47 1.46 0.0522 0.0402 0.0562 0.0428 0.0654 0.0494 0.0734 0.0548 0.0596 0.0446

48 1.47 0.0524 0.0404 0.0564 0.0431 0.0658 0.0498 0.0738 0.0551 0.0597 0.0447

49 1.48 0.0526 0.0406 0.0566 0.0434 0.0662 0.0502 0.0742 0.0554 0.0598 0.0448

50 1.49 0.0528 0.0408 0.0568 0.0437 0.0666 0.0506 0.0746 0.0557 0.0599 0.0449

51 1.50 0.0530 0.0410 0.0570 0.0440 0.0670 0.0510 0.0750 0.0560 0.0600 0.0450

52 1.51 0.0533 0.0412 0.0573 0.0442 0.0674 0.0513 0.0754 0.0563 0.0602 0.0452
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 2 3 4 5 6 7 8 9 10 11
Short Span Coefficients (a x)

One Short Edge One Long Edge Two Adjacent Edges Two Short Edges
Interior Panels
Discontinuous Discontinuous Discontinuous Discontinuous

S.No. Values of ( ly / lx ) Negative Negative Negative Negative Negative

Positive Positive Positive Positive Positive
moment at moment at moment at moment at moment at
moment at moment at moment at moment at moment at
continuous continuous continuous continuous continuous
midspan midspan midspan midspan midspan
edge edge edge edge edge

53 1.52 0.0536 0.0413 0.0576 0.0443 0.0678 0.0516 0.0757 0.0566 0.0604 0.0453

54 1.53 0.0538 0.0415 0.0578 0.0445 0.0682 0.0520 0.0761 0.0568 0.0606 0.0455

55 1.54 0.0541 0.0416 0.0581 0.0446 0.0686 0.0523 0.0764 0.0571 0.0608 0.0456

56 1.55 0.0544 0.0418 0.0584 0.0448 0.0690 0.0526 0.0768 0.0574 0.0610 0.0458

57 1.56 0.0547 0.0420 0.0587 0.0450 0.0694 0.0529 0.0772 0.0577 0.0612 0.0460

58 1.57 0.0550 0.0421 0.0590 0.0451 0.0698 0.0532 0.0775 0.0580 0.0614 0.0461

59 1.58 0.0552 0.0423 0.0592 0.0453 0.0702 0.0536 0.0779 0.0582 0.0616 0.0463

60 1.59 0.0555 0.0424 0.0595 0.0454 0.0706 0.0539 0.0782 0.0585 0.0618 0.0464

61 1.60 0.0558 0.0426 0.0598 0.0456 0.0710 0.0542 0.0786 0.0588 0.0620 0.0466

62 1.61 0.0561 0.0428 0.0601 0.0458 0.0714 0.0545 0.0790 0.0591 0.0622 0.0468

63 1.62 0.0564 0.0429 0.0604 0.0459 0.0718 0.0548 0.0793 0.0594 0.0624 0.0469

64 1.63 0.0566 0.0431 0.0606 0.0461 0.0722 0.0552 0.0797 0.0596 0.0626 0.0471
65 1.64 0.0569 0.0432 0.0609 0.0462 0.0726 0.0555 0.0800 0.0599 0.0628 0.0472
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 2 3 4 5 6 7 8 9 10 11
Short Span Coefficients (a x)

One Short Edge One Long Edge Two Adjacent Edges Two Short Edges
Interior Panels
Discontinuous Discontinuous Discontinuous Discontinuous

S.No. Values of ( ly / lx ) Negative Negative Negative Negative Negative

Positive Positive Positive Positive Positive
moment at moment at moment at moment at moment at
moment at moment at moment at moment at moment at
continuous continuous continuous continuous continuous
midspan midspan midspan midspan midspan
edge edge edge edge edge

66 1.65 0.0572 0.0434 0.0612 0.0464 0.0730 0.0558 0.0804 0.0602 0.0630 0.0474

67 1.66 0.0575 0.0436 0.0615 0.0466 0.0734 0.0561 0.0808 0.0605 0.0632 0.0476

68 1.67 0.0578 0.0437 0.0618 0.0467 0.0738 0.0564 0.0811 0.0608 0.0634 0.0477

69 1.68 0.0580 0.0439 0.0620 0.0469 0.0742 0.0568 0.0815 0.0610 0.0636 0.0479

70 1.69 0.0583 0.0440 0.0623 0.0470 0.0746 0.0571 0.0818 0.0613 0.0638 0.0480

71 1.70 0.0586 0.0442 0.0626 0.0472 0.0750 0.0574 0.0822 0.0616 0.0640 0.0482

72 1.71 0.0589 0.0444 0.0629 0.0474 0.0754 0.0577 0.0826 0.0619 0.0642 0.0484

73 1.72 0.0592 0.0445 0.0632 0.0475 0.0758 0.0580 0.0829 0.0622 0.0644 0.0485

74 1.73 0.0594 0.0447 0.0634 0.0477 0.0762 0.0584 0.0833 0.0624 0.0646 0.0487

75 1.74 0.0597 0.0448 0.0637 0.0478 0.0766 0.0587 0.0836 0.0627 0.0648 0.0488

76 1.75 0.0600 0.0450 0.0640 0.0480 0.0770 0.0590 0.0840 0.0630 0.0650 0.0490

77 1.76 0.0602 0.0452 0.0642 0.0482 0.0773 0.0592 0.0843 0.0632 0.0652 0.0491
78 1.77 0.0604 0.0453 0.0643 0.0483 0.0776 0.0595 0.0846 0.0635 0.0653 0.0492
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 2 3 4 5 6 7 8 9 10 11
Short Span Coefficients (a x)

One Short Edge One Long Edge Two Adjacent Edges Two Short Edges
Interior Panels
Discontinuous Discontinuous Discontinuous Discontinuous

S.No. Values of ( ly / lx ) Negative Negative Negative Negative Negative

Positive Positive Positive Positive Positive
moment at moment at moment at moment at moment at
moment at moment at moment at moment at moment at
continuous continuous continuous continuous continuous
midspan midspan midspan midspan midspan
edge edge edge edge edge

79 1.78 0.0606 0.0455 0.0645 0.0485 0.0780 0.0597 0.0848 0.0637 0.0655 0.0494

80 1.79 0.0608 0.0456 0.0646 0.0486 0.0783 0.0600 0.0851 0.0640 0.0656 0.0495

81 1.80 0.0610 0.0458 0.0648 0.0488 0.0786 0.0602 0.0854 0.0642 0.0658 0.0496

82 1.81 0.0612 0.0460 0.0650 0.0490 0.0789 0.0604 0.0857 0.0644 0.0660 0.0497

83 1.82 0.0614 0.0461 0.0651 0.0491 0.0792 0.0607 0.0860 0.0647 0.0661 0.0498

84 1.83 0.0616 0.0463 0.0653 0.0493 0.0796 0.0609 0.0862 0.0649 0.0663 0.0500

85 1.84 0.0618 0.0464 0.0654 0.0494 0.0799 0.0612 0.0865 0.0652 0.0664 0.0501

86 1.85 0.0620 0.0466 0.0656 0.0496 0.0802 0.0614 0.0868 0.0654 0.0666 0.0502

87 1.86 0.0622 0.0468 0.0658 0.0498 0.0805 0.0616 0.0871 0.0656 0.0668 0.0503

88 1.87 0.0624 0.0469 0.0659 0.0499 0.0808 0.0619 0.0874 0.0659 0.0669 0.0504

89 1.88 0.0626 0.0471 0.0661 0.0501 0.0812 0.0621 0.0876 0.0661 0.0671 0.0506

90 1.89 0.0628 0.0472 0.0662 0.0502 0.0815 0.0624 0.0879 0.0664 0.0672 0.0507
91 1.90 0.0630 0.0474 0.0664 0.0504 0.0818 0.0626 0.0882 0.0666 0.0674 0.0508
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 2 3 4 5 6 7 8 9 10 11
Short Span Coefficients (a x)

One Short Edge One Long Edge Two Adjacent Edges Two Short Edges
Interior Panels
Discontinuous Discontinuous Discontinuous Discontinuous

S.No. Values of ( ly / lx ) Negative Negative Negative Negative Negative

Positive Positive Positive Positive Positive
moment at moment at moment at moment at moment at
moment at moment at moment at moment at moment at
continuous continuous continuous continuous continuous
midspan midspan midspan midspan midspan
edge edge edge edge edge

92 1.91 0.0632 0.0476 0.0666 0.0506 0.0821 0.0628 0.0885 0.0668 0.0676 0.0509

93 1.92 0.0634 0.0477 0.0667 0.0507 0.0824 0.0631 0.0888 0.0671 0.0677 0.0510

94 1.93 0.0636 0.0479 0.0669 0.0509 0.0828 0.0633 0.0890 0.0673 0.0679 0.0512

95 1.94 0.0638 0.0480 0.0670 0.0510 0.0831 0.0636 0.0893 0.0676 0.0680 0.0513

96 1.95 0.0640 0.0482 0.0672 0.0512 0.0834 0.0638 0.0896 0.0678 0.0682 0.0514

97 1.96 0.0642 0.0484 0.0674 0.0514 0.0837 0.0640 0.0899 0.0680 0.0684 0.0515

98 1.97 0.0644 0.0485 0.0675 0.0515 0.0840 0.0643 0.0902 0.0683 0.0685 0.0516

99 1.98 0.0646 0.0487 0.0677 0.0517 0.0844 0.0645 0.0904 0.0685 0.0687 0.0518

100 1.99 0.0648 0.0488 0.0678 0.0518 0.0847 0.0648 0.0907 0.0688 0.0688 0.0519

101 2.00 0.0650 0.0490 0.0680 0.0520 0.0850 0.0650 0.0910 0.0690 0.0690 0.0520
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 12 13 14 15 16 17 18
Short Span Coefficients (a x)
Three Edges Three Edges
Two Long Edges
Discontinuous (One Long Discontinuous (One Four Edges Discontinuous
Discontinuous
Edge Continuous) Short Edge Continuous)
S.No. Values of ( ly / lx ) Negative Negative Negative Negative
Positive Positive Positive Positive
moment at moment at moment at moment at
moment at moment at moment at moment at
continuous continuous continuous continuous
midspan midspan midspan midspan
edge edge edge edge

1 1.00 0.0000 0.0350 0.0570 0.0430 0.0000 0.0430 0.0000 0.0560

2 1.01 0.0000 0.0358 0.0577 0.0435 0.0000 0.0438 0.0000 0.0568

3 1.02 0.0000 0.0366 0.0584 0.0440 0.0000 0.0446 0.0000 0.0576

4 1.03 0.0000 0.0374 0.0591 0.0445 0.0000 0.0454 0.0000 0.0584

5 1.04 0.0000 0.0382 0.0598 0.0450 0.0000 0.0462 0.0000 0.0592

6 1.05 0.0000 0.0390 0.0605 0.0455 0.0000 0.0470 0.0000 0.0600

7 1.06 0.0000 0.0398 0.0612 0.0460 0.0000 0.0478 0.0000 0.0608

8 1.07 0.0000 0.0406 0.0619 0.0465 0.0000 0.0486 0.0000 0.0616

9 1.08 0.0000 0.0414 0.0626 0.0470 0.0000 0.0494 0.0000 0.0624

10 1.09 0.0000 0.0422 0.0633 0.0475 0.0000 0.0502 0.0000 0.0632

11 1.10 0.0000 0.0430 0.0640 0.0480 0.0000 0.0510 0.0000 0.0640

12 1.11 0.0000 0.0438 0.0647 0.0485 0.0000 0.0518 0.0000 0.0648

13 1.12 0.0000 0.0446 0.0654 0.0490 0.0000 0.0526 0.0000 0.0656
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 12 13 14 15 16 17 18
Short Span Coefficients (a x)
Three Edges Three Edges
Two Long Edges
Discontinuous (One Long Discontinuous (One Four Edges Discontinuous
Discontinuous
Edge Continuous) Short Edge Continuous)
S.No. Values of ( ly / lx ) Negative Negative Negative Negative
Positive Positive Positive Positive
moment at moment at moment at moment at
moment at moment at moment at moment at
continuous continuous continuous continuous
midspan midspan midspan midspan
edge edge edge edge

14 1.13 0.0000 0.0454 0.0661 0.0495 0.0000 0.0534 0.0000 0.0664

15 1.14 0.0000 0.0462 0.0668 0.0500 0.0000 0.0542 0.0000 0.0672

16 1.15 0.0000 0.0470 0.0675 0.0505 0.0000 0.0550 0.0000 0.0680

17 1.16 0.0000 0.0478 0.0682 0.0510 0.0000 0.0558 0.0000 0.0688

18 1.17 0.0000 0.0486 0.0689 0.0515 0.0000 0.0566 0.0000 0.0696

19 1.18 0.0000 0.0494 0.0696 0.0520 0.0000 0.0574 0.0000 0.0704

20 1.19 0.0000 0.0502 0.0703 0.0525 0.0000 0.0582 0.0000 0.0712

21 1.20 0.0000 0.0510 0.0710 0.0530 0.0000 0.0590 0.0000 0.0720

22 1.21 0.0000 0.0516 0.0715 0.0534 0.0000 0.0596 0.0000 0.0727

23 1.22 0.0000 0.0522 0.0720 0.0538 0.0000 0.0602 0.0000 0.0734

24 1.23 0.0000 0.0528 0.0725 0.0542 0.0000 0.0608 0.0000 0.0741

25 1.24 0.0000 0.0534 0.0730 0.0546 0.0000 0.0614 0.0000 0.0748

26 1.25 0.0000 0.0540 0.0735 0.0550 0.0000 0.0620 0.0000 0.0755
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 12 13 14 15 16 17 18
Short Span Coefficients (a x)
Three Edges Three Edges
Two Long Edges
Discontinuous (One Long Discontinuous (One Four Edges Discontinuous
Discontinuous
Edge Continuous) Short Edge Continuous)
S.No. Values of ( ly / lx ) Negative Negative Negative Negative
Positive Positive Positive Positive
moment at moment at moment at moment at
moment at moment at moment at moment at
continuous continuous continuous continuous
midspan midspan midspan midspan
edge edge edge edge

27 1.26 0.0000 0.0546 0.0740 0.0554 0.0000 0.0626 0.0000 0.0762

28 1.27 0.0000 0.0552 0.0745 0.0558 0.0000 0.0632 0.0000 0.0769

29 1.28 0.0000 0.0558 0.0750 0.0562 0.0000 0.0638 0.0000 0.0776

30 1.29 0.0000 0.0564 0.0755 0.0566 0.0000 0.0644 0.0000 0.0783

31 1.30 0.0000 0.0570 0.0760 0.0570 0.0000 0.0650 0.0000 0.0790

32 1.31 0.0000 0.0576 0.0764 0.0573 0.0000 0.0656 0.0000 0.0796

33 1.32 0.0000 0.0582 0.0768 0.0576 0.0000 0.0662 0.0000 0.0802

34 1.33 0.0000 0.0588 0.0772 0.0579 0.0000 0.0668 0.0000 0.0808

35 1.34 0.0000 0.0594 0.0776 0.0582 0.0000 0.0674 0.0000 0.0814

36 1.35 0.0000 0.0600 0.0780 0.0585 0.0000 0.0680 0.0000 0.0820

37 1.36 0.0000 0.0606 0.0784 0.0588 0.0000 0.0686 0.0000 0.0826

38 1.37 0.0000 0.0612 0.0788 0.0591 0.0000 0.0692 0.0000 0.0832

39 1.38 0.0000 0.0618 0.0792 0.0594 0.0000 0.0698 0.0000 0.0838
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 12 13 14 15 16 17 18
Short Span Coefficients (a x)
Three Edges Three Edges
Two Long Edges
Discontinuous (One Long Discontinuous (One Four Edges Discontinuous
Discontinuous
Edge Continuous) Short Edge Continuous)
S.No. Values of ( ly / lx ) Negative Negative Negative Negative
Positive Positive Positive Positive
moment at moment at moment at moment at
moment at moment at moment at moment at
continuous continuous continuous continuous
midspan midspan midspan midspan
edge edge edge edge

40 1.39 0.0000 0.0624 0.0796 0.0597 0.0000 0.0704 0.0000 0.0844

41 1.40 0.0000 0.0630 0.0800 0.0600 0.0000 0.0710 0.0000 0.0850

42 1.41 0.0000 0.0635 0.0804 0.0604 0.0000 0.0715 0.0000 0.0854

43 1.42 0.0000 0.0640 0.0808 0.0608 0.0000 0.0720 0.0000 0.0858

44 1.43 0.0000 0.0645 0.0812 0.0612 0.0000 0.0725 0.0000 0.0862

45 1.44 0.0000 0.0650 0.0816 0.0616 0.0000 0.0730 0.0000 0.0866

46 1.45 0.0000 0.0655 0.0820 0.0620 0.0000 0.0735 0.0000 0.0870

47 1.46 0.0000 0.0660 0.0824 0.0624 0.0000 0.0740 0.0000 0.0874

48 1.47 0.0000 0.0665 0.0828 0.0628 0.0000 0.0745 0.0000 0.0878

49 1.48 0.0000 0.0670 0.0832 0.0632 0.0000 0.0750 0.0000 0.0882

50 1.49 0.0000 0.0675 0.0836 0.0636 0.0000 0.0755 0.0000 0.0886

51 1.50 0.0000 0.0680 0.0840 0.0640 0.0000 0.0760 0.0000 0.0890

52 1.51 0.0000 0.0685 0.0843 0.0642 0.0000 0.0764 0.0000 0.0894

 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 12 13 14 15 16 17 18
Short Span Coefficients (a x)
Three Edges Three Edges
Two Long Edges
Discontinuous (One Long Discontinuous (One Four Edges Discontinuous
Discontinuous
Edge Continuous) Short Edge Continuous)
S.No. Values of ( ly / lx ) Negative Negative Negative Negative
Positive Positive Positive Positive
moment at moment at moment at moment at
moment at moment at moment at moment at
continuous continuous continuous continuous
midspan midspan midspan midspan
edge edge edge edge

53 1.52 0.0000 0.0690 0.0846 0.0644 0.0000 0.0769 0.0000 0.0899

54 1.53 0.0000 0.0694 0.0848 0.0646 0.0000 0.0773 0.0000 0.0903

55 1.54 0.0000 0.0699 0.0851 0.0648 0.0000 0.0778 0.0000 0.0908

56 1.55 0.0000 0.0704 0.0854 0.0650 0.0000 0.0782 0.0000 0.0912

57 1.56 0.0000 0.0709 0.0857 0.0652 0.0000 0.0786 0.0000 0.0916

58 1.57 0.0000 0.0714 0.0860 0.0654 0.0000 0.0791 0.0000 0.0921

59 1.58 0.0000 0.0718 0.0862 0.0656 0.0000 0.0795 0.0000 0.0925

60 1.59 0.0000 0.0723 0.0865 0.0658 0.0000 0.0800 0.0000 0.0930

61 1.60 0.0000 0.0728 0.0868 0.0660 0.0000 0.0804 0.0000 0.0934

62 1.61 0.0000 0.0733 0.0871 0.0662 0.0000 0.0808 0.0000 0.0938

63 1.62 0.0000 0.0738 0.0874 0.0664 0.0000 0.0813 0.0000 0.0943

64 1.63 0.0000 0.0742 0.0876 0.0666 0.0000 0.0817 0.0000 0.0947

65 1.64 0.0000 0.0747 0.0879 0.0668 0.0000 0.0822 0.0000 0.0952
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 12 13 14 15 16 17 18
Short Span Coefficients (a x)
Three Edges Three Edges
Two Long Edges
Discontinuous (One Long Discontinuous (One Four Edges Discontinuous
Discontinuous
Edge Continuous) Short Edge Continuous)
S.No. Values of ( ly / lx ) Negative Negative Negative Negative
Positive Positive Positive Positive
moment at moment at moment at moment at
moment at moment at moment at moment at
continuous continuous continuous continuous
midspan midspan midspan midspan
edge edge edge edge

66 1.65 0.0000 0.0752 0.0882 0.0670 0.0000 0.0826 0.0000 0.0956

67 1.66 0.0000 0.0757 0.0885 0.0672 0.0000 0.0830 0.0000 0.0960

68 1.67 0.0000 0.0762 0.0888 0.0674 0.0000 0.0835 0.0000 0.0965

69 1.68 0.0000 0.0766 0.0890 0.0676 0.0000 0.0839 0.0000 0.0969

70 1.69 0.0000 0.0771 0.0893 0.0678 0.0000 0.0844 0.0000 0.0974

71 1.70 0.0000 0.0776 0.0896 0.0680 0.0000 0.0848 0.0000 0.0978

72 1.71 0.0000 0.0781 0.0899 0.0682 0.0000 0.0852 0.0000 0.0982

73 1.72 0.0000 0.0786 0.0902 0.0684 0.0000 0.0857 0.0000 0.0987

74 1.73 0.0000 0.0790 0.0904 0.0686 0.0000 0.0861 0.0000 0.0991

75 1.74 0.0000 0.0795 0.0907 0.0688 0.0000 0.0866 0.0000 0.0996

76 1.75 0.0000 0.0800 0.0910 0.0690 0.0000 0.0870 0.0000 0.1000

77 1.76 0.0000 0.0803 0.0912 0.0692 0.0000 0.0874 0.0000 0.1003

78 1.77 0.0000 0.0806 0.0915 0.0693 0.0000 0.0877 0.0000 0.1006
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 12 13 14 15 16 17 18
Short Span Coefficients (a x)
Three Edges Three Edges
Two Long Edges
Discontinuous (One Long Discontinuous (One Four Edges Discontinuous
Discontinuous
Edge Continuous) Short Edge Continuous)
S.No. Values of ( ly / lx ) Negative Negative Negative Negative
Positive Positive Positive Positive
moment at moment at moment at moment at
moment at moment at moment at moment at
continuous continuous continuous continuous
midspan midspan midspan midspan
edge edge edge edge

79 1.78 0.0000 0.0810 0.0917 0.0695 0.0000 0.0881 0.0000 0.1008

80 1.79 0.0000 0.0813 0.0920 0.0696 0.0000 0.0884 0.0000 0.1011

81 1.80 0.0000 0.0816 0.0922 0.0698 0.0000 0.0888 0.0000 0.1014

82 1.81 0.0000 0.0819 0.0924 0.0700 0.0000 0.0892 0.0000 0.1017

83 1.82 0.0000 0.0822 0.0927 0.0701 0.0000 0.0895 0.0000 0.1020

84 1.83 0.0000 0.0826 0.0929 0.0703 0.0000 0.0899 0.0000 0.1022

85 1.84 0.0000 0.0829 0.0932 0.0704 0.0000 0.0902 0.0000 0.1025

86 1.85 0.0000 0.0832 0.0934 0.0706 0.0000 0.0906 0.0000 0.1028

87 1.86 0.0000 0.0835 0.0936 0.0708 0.0000 0.0910 0.0000 0.1031

88 1.87 0.0000 0.0838 0.0939 0.0709 0.0000 0.0913 0.0000 0.1034

89 1.88 0.0000 0.0842 0.0941 0.0711 0.0000 0.0917 0.0000 0.1036

90 1.89 0.0000 0.0845 0.0944 0.0712 0.0000 0.0920 0.0000 0.1039

91 1.90 0.0000 0.0848 0.0946 0.0714 0.0000 0.0924 0.0000 0.1042
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels supported on four sides with Provision for Torsion at corners

CLAUSE D - 1.1 and 24.4.1

1 12 13 14 15 16 17 18
Short Span Coefficients (a x)
Three Edges Three Edges
Two Long Edges
Discontinuous (One Long Discontinuous (One Four Edges Discontinuous
Discontinuous
Edge Continuous) Short Edge Continuous)
S.No. Values of ( ly / lx ) Negative Negative Negative Negative
Positive Positive Positive Positive
moment at moment at moment at moment at
moment at moment at moment at moment at
continuous continuous continuous continuous
midspan midspan midspan midspan
edge edge edge edge

92 1.91 0.0000 0.0851 0.0948 0.0716 0.0000 0.0928 0.0000 0.1045

93 1.92 0.0000 0.0854 0.0951 0.0717 0.0000 0.0931 0.0000 0.1048

94 1.93 0.0000 0.0858 0.0953 0.0719 0.0000 0.0935 0.0000 0.1050

95 1.94 0.0000 0.0861 0.0956 0.0720 0.0000 0.0938 0.0000 0.1053

96 1.95 0.0000 0.0864 0.0958 0.0722 0.0000 0.0942 0.0000 0.1056

97 1.96 0.0000 0.0867 0.0960 0.0724 0.0000 0.0946 0.0000 0.1059

98 1.97 0.0000 0.0870 0.0963 0.0725 0.0000 0.0949 0.0000 0.1062

99 1.98 0.0000 0.0874 0.0965 0.0727 0.0000 0.0953 0.0000 0.1064

100 1.99 0.0000 0.0877 0.0968 0.0728 0.0000 0.0956 0.0000 0.1067

101 2.00 0.0000 0.0880 0.0970 0.0730 0.0000 0.0960 0.0000 0.1070
 1

S.No. Values of ( ly / lx )

1 1.00

2 1.01

3 1.02

4 1.03

5 1.04

6 1.05

7 1.06

8 1.07

9 1.08

10 1.09

11 1.10

12 1.11

13 1.12
 CODE IS 456

TABLE Table 26

TITLE BM Coefficients for Rectangular Panels

CLAUSE D - 1.1 and 24.4.1

1 2

Case.
Type of Panel Moments considered
No.

Negative moment at continuous edge 1

1 Interior Panels
Positive moment at midspan 2

Negative moment at continuous edge 3

One Short Edge
2
Discontinuous
Positive moment at midspan 4

Negative moment at continuous edge 5

One Long Edge
3
Discontinuous
Positive moment at midspan 6

Two Adjacent Negative moment at continuous edge 7

4 Edges
Discontinuous Positive moment at midspan 8

Negative moment at continuous edge 9

Two Short Edges
5
Discontinuous
Positive moment at midspan 10

Negative moment at continuous edge 11

Two Long Edges
6
Discontinuous
Positive moment at midspan 12

Three Edges Negative moment at continuous edge 13

Discontinuous
7
(One Long Edge
Continuous) Positive moment at midspan 14

Three Edges Negative moment at continuous edge 15

Discontinuous
8
(One Short Edge
Continuous) Positive moment at midspan 16

Negative moment at continuous edge 17

Four Edges
9
Discontinuous
Positive moment at midspan 18
for Rectangular Panels

Long Span Coefficients (a y)

0.032

0.024

0.037

0.028

0.037

0.028

0.047

0.035

0.000

0.035

0.045

0.035

0.000

0.043

0.057

0.043

0.000

0.056
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

Tensile Reinforcement percentage equation can be written as,

0.87464 (fy2/fck) (pt/100)2 - 0.87 fy (pt/100) + (Mu/bd2) = 0

Grade of Concrete, fck = 25 N/mm2

Mu / bd2, Grade of Steel, fy in N/mm2

S.No.
N/mm2
250 415 500

1 0.00 0.000 0.000 0.000

2 0.01 0.005 0.003 0.002

3 0.02 0.009 0.006 0.005

4 0.03 0.014 0.008 0.007

5 0.04 0.018 0.011 0.009

6 0.05 0.023 0.014 0.012

7 0.06 0.028 0.017 0.014

8 0.07 0.032 0.019 0.016

9 0.08 0.037 0.022 0.018

10 0.09 0.042 0.025 0.021

11 0.10 0.046 0.028 0.023

12 0.11 0.051 0.031 0.025

13 0.12 0.056 0.033 0.028

14 0.13 0.060 0.036 0.030

15 0.14 0.065 0.039 0.032

16 0.15 0.069 0.042 0.035

17 0.16 0.074 0.045 0.037

18 0.17 0.079 0.047 0.039

19 0.18 0.083 0.050 0.042

20 0.19 0.088 0.053 0.044

21 0.2 0.093 0.056 0.046

22 0.21 0.098 0.059 0.049

23 0.22 0.102 0.062 0.051

24 0.23 0.107 0.064 0.053

25 0.24 0.112 0.067 0.056

calc pt
361937360.xls
22 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

26 0.25 0.116 0.070 0.058

27 0.26 0.121 0.073 0.061

28 0.27 0.126 0.076 0.063

29 0.28 0.130 0.079 0.065

30 0.29 0.135 0.081 0.068

31 0.30 0.140 0.084 0.070

32 0.31 0.145 0.087 0.072

33 0.32 0.149 0.090 0.075

34 0.33 0.154 0.093 0.077

35 0.34 0.159 0.096 0.079

36 0.35 0.164 0.099 0.082

37 0.36 0.168 0.101 0.084

38 0.37 0.173 0.104 0.087

39 0.38 0.178 0.107 0.089

40 0.39 0.183 0.110 0.091

41 0.40 0.188 0.113 0.094

42 0.41 0.192 0.116 0.096

43 0.42 0.197 0.119 0.099

44 0.43 0.202 0.122 0.101

45 0.44 0.207 0.124 0.103

46 0.45 0.211 0.127 0.106

47 0.46 0.216 0.130 0.108

48 0.47 0.221 0.133 0.111

49 0.48 0.226 0.136 0.113

50 0.49 0.231 0.139 0.115

51 0.50 0.236 0.142 0.118

52 0.51 0.240 0.145 0.120

53 0.52 0.245 0.148 0.123

54 0.53 0.250 0.151 0.125

55 0.54 0.255 0.154 0.127

56 0.55 0.260 0.156 0.130

57 0.56 0.265 0.159 0.132

58 0.57 0.269 0.162 0.135

calc pt
361937360.xls
23 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

59 0.58 0.274 0.165 0.137

60 0.59 0.279 0.168 0.140

61 0.60 0.284 0.171 0.142

62 0.61 0.289 0.174 0.144

63 0.62 0.294 0.177 0.147

64 0.63 0.299 0.180 0.149

65 0.64 0.304 0.183 0.152

66 0.65 0.309 0.186 0.154

67 0.66 0.313 0.189 0.157

68 0.67 0.318 0.192 0.159

69 0.68 0.323 0.195 0.162

70 0.69 0.328 0.198 0.164

71 0.70 0.333 0.201 0.167

72 0.71 0.338 0.204 0.169

73 0.72 0.343 0.207 0.171

74 0.73 0.348 0.210 0.174

75 0.74 0.353 0.213 0.176

76 0.75 0.358 0.216 0.179

77 0.76 0.363 0.219 0.181

78 0.77 0.368 0.222 0.184

79 0.78 0.373 0.225 0.186

80 0.79 0.378 0.228 0.189

81 0.80 0.383 0.231 0.191

82 0.81 0.388 0.234 0.194

83 0.82 0.393 0.237 0.196

84 0.83 0.398 0.240 0.199

85 0.84 0.403 0.243 0.201

86 0.85 0.408 0.246 0.204

87 0.86 0.413 0.249 0.206

88 0.87 0.418 0.252 0.209

89 0.88 0.423 0.255 0.211

90 0.89 0.428 0.258 0.214

91 0.90 0.433 0.261 0.216

calc pt
361937360.xls
24 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

92 0.91 0.438 0.264 0.219

93 0.92 0.443 0.267 0.221

94 0.93 0.448 0.270 0.224

95 0.94 0.453 0.273 0.226

96 0.95 0.458 0.276 0.229

97 0.96 0.463 0.279 0.232

98 0.97 0.468 0.282 0.234

99 0.98 0.473 0.285 0.237

100 0.99 0.478 0.288 0.239

101 1.00 0.483 0.291 0.242

102 1.01 0.489 0.294 0.244

103 1.02 0.494 0.297 0.247

104 1.03 0.499 0.300 0.249

105 1.04 0.504 0.304 0.252

106 1.05 0.509 0.307 0.254

107 1.06 0.514 0.310 0.257

108 1.07 0.519 0.313 0.260

109 1.08 0.524 0.316 0.262

110 1.09 0.529 0.319 0.265

111 1.10 0.535 0.322 0.267

112 1.11 0.540 0.325 0.270

113 1.12 0.545 0.328 0.272

114 1.13 0.550 0.331 0.275

115 1.14 0.555 0.335 0.278

116 1.15 0.560 0.338 0.280

117 1.16 0.566 0.341 0.283

118 1.17 0.571 0.344 0.285

119 1.18 0.576 0.347 0.288

120 1.19 0.581 0.350 0.291

121 1.20 0.586 0.353 0.293

122 1.21 0.592 0.356 0.296

123 1.22 0.597 0.360 0.298

124 1.23 0.602 0.363 0.301

calc pt
361937360.xls
25 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

125 1.24 0.607 0.366 0.304

126 1.25 0.613 0.369 0.306

127 1.26 0.618 0.372 0.309

128 1.27 0.623 0.375 0.312

129 1.28 0.628 0.379 0.314

130 1.29 0.634 0.382 0.317

131 1.30 0.639 0.385 0.319

132 1.31 0.644 0.388 0.322

133 1.32 0.649 0.391 0.325

134 1.33 0.655 0.394 0.327

135 1.34 0.660 0.398 0.330

136 1.35 0.665 0.401 0.333

137 1.36 0.671 0.404 0.335

138 1.37 0.676 0.407 0.338

139 1.38 0.681 0.410 0.341

140 1.39 0.687 0.414 0.343

141 1.40 0.692 0.417 0.346

142 1.41 0.697 0.420 0.349

143 1.42 0.703 0.423 0.351

144 1.43 0.708 0.427 0.354

145 1.44 0.713 0.430 0.357

146 1.45 0.719 0.433 0.359

147 1.46 0.724 0.436 0.362

148 1.47 0.730 0.440 0.365

149 1.48 0.735 0.443 0.367

150 1.49 0.740 0.446 0.370

151 1.50 0.746 0.449 0.373

152 1.51 0.751 0.453 0.376

153 1.52 0.757 0.456 0.378

154 1.53 0.762 0.459 0.381

155 1.54 0.767 0.462 0.384

156 1.55 0.773 0.466 0.386

157 1.56 0.778 0.469 0.389

calc pt
361937360.xls
26 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

158 1.57 0.784 0.472 0.392

159 1.58 0.789 0.475 0.395

160 1.59 0.795 0.479 0.397

161 1.60 0.800 0.482 0.400

162 1.61 0.806 0.485 0.403

163 1.62 0.811 0.489 0.406

164 1.63 0.817 0.492 0.408

165 1.64 0.822 0.495 0.411

166 1.65 0.828 0.499 0.414

167 1.66 0.833 0.502 0.417

168 1.67 0.839 0.505 0.419

169 1.68 0.844 0.509 0.422

170 1.69 0.850 0.512 0.425

171 1.70 0.855 0.515 0.428

172 1.71 0.861 0.519 0.430

173 1.72 0.867 0.522 0.433

174 1.73 0.872 0.525 0.436

175 1.74 0.878 0.529 0.439

176 1.75 0.883 0.532 0.442

177 1.76 0.889 0.535 0.444

178 1.77 0.894 0.539 0.447

179 1.78 0.900 0.542 0.450

180 1.79 0.906 0.546 0.453

181 1.80 0.911 0.549 0.456

182 1.81 0.917 0.552 0.458

183 1.82 0.923 0.556 0.461

184 1.83 0.928 0.559 0.464

185 1.84 0.934 0.563 0.467

186 1.85 0.940 0.566 0.470

187 1.86 0.945 0.569 0.473

188 1.87 0.951 0.573 0.475

189 1.88 0.957 0.576 0.478

190 1.89 0.962 0.580 0.481

calc pt
361937360.xls
27 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

191 1.90 0.968 0.583 0.484

192 1.91 0.974 0.587 0.487

193 1.92 0.979 0.590 0.490

194 1.93 0.985 0.593 0.493

195 1.94 0.991 0.597 0.495

196 1.95 0.997 0.600 0.498

197 1.96 1.002 0.604 0.501

198 1.97 1.008 0.607 0.504

199 1.98 1.014 0.611 0.507

200 1.99 1.020 0.614 0.510

201 2.00 1.026 0.618 0.513

202 2.01 1.031 0.621 0.516

203 2.02 1.037 0.625 0.519

204 2.03 1.043 0.628 0.521

205 2.04 1.049 0.632 0.524

206 2.05 1.055 0.635 0.527

207 2.06 1.060 0.639 0.530

208 2.07 1.066 0.642 0.533

209 2.08 1.072 0.646 0.536

210 2.09 1.078 0.649 0.539

211 2.10 1.084 0.653 0.542

212 2.11 1.090 0.657 0.545

213 2.12 1.096 0.660 0.548

214 2.13 1.102 0.664 0.551

215 2.14 1.108 0.667 0.554

216 2.15 1.113 0.671 0.557

217 2.16 1.119 0.674 0.560

218 2.17 1.125 0.678 0.563

219 2.18 1.131 0.681 0.566

220 2.19 1.137 0.685 0.569

221 2.20 1.143 0.689 0.572

222 2.21 1.149 0.692 0.575

223 2.22 1.155 0.696 0.578

calc pt
361937360.xls
28 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

224 2.23 1.161 0.699 0.581

225 2.24 1.167 0.703 0.584

226 2.25 1.173 0.707 0.587

227 2.26 1.179 0.710 0.590

228 2.27 1.185 0.714 0.593

229 2.28 1.191 0.718 0.596

230 2.29 1.197 0.721 0.599

231 2.30 1.203 0.725 0.602

232 2.31 1.209 0.729 0.605

233 2.32 1.216 0.732 0.608

234 2.33 1.222 0.736 0.611

235 2.34 1.228 0.740 0.614

236 2.35 1.234 0.743 0.617

237 2.36 1.240 0.747 0.620

238 2.37 1.246 0.751 0.623

239 2.38 1.252 0.754 0.626

240 2.39 1.258 0.758 0.629

241 2.40 1.265 0.762 0.632

242 2.41 1.271 0.765 0.635

243 2.42 1.277 0.769 0.638

244 2.43 1.283 0.773 0.642

245 2.44 1.289 0.777 0.645

246 2.45 1.295 0.780 0.648

247 2.46 1.302 0.784 0.651

248 2.47 1.308 0.788 0.654

249 2.48 1.314 0.792 0.657

250 2.49 1.320 0.795 0.660

251 2.50 1.327 0.799 0.663

252 2.51 1.333 0.803 0.666

253 2.52 1.339 0.807 0.670

254 2.53 1.346 0.811 0.673

255 2.54 1.352 0.814 0.676

256 2.55 1.358 0.818 0.679

calc pt
361937360.xls
29 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

257 2.56 1.365 0.822 0.682

258 2.57 1.371 0.826 0.685

259 2.58 1.377 0.830 0.689

260 2.59 1.384 0.833 0.692

261 2.60 1.390 0.837 0.695

262 2.61 1.396 0.841 0.698

263 2.62 1.403 0.845 0.701

264 2.63 1.409 0.849 0.705

265 2.64 1.416 0.853 0.708

266 2.65 1.422 0.857 0.711

267 2.66 1.428 0.861 0.714

268 2.67 1.435 0.864 0.717

269 2.68 1.441 0.868 0.721

270 2.69 1.448 0.872 0.724

271 2.70 1.454 0.876 0.727

272 2.71 1.461 0.880 0.730

273 2.72 1.467 0.884 0.734

274 2.73 1.474 0.888 0.737

275 2.74 1.480 0.892 0.740

276 2.75 1.487 0.896 0.744

277 2.76 1.494 0.900 0.747

278 2.77 1.500 0.904 0.750

279 2.78 1.507 0.908 0.753

280 2.79 1.513 0.912 0.757

281 2.80 1.520 0.916 0.760

282 2.81 1.527 0.920 0.763

283 2.82 1.533 0.924 0.767

284 2.83 1.540 0.928 0.770

285 2.84 1.547 0.932 0.773

286 2.85 1.553 0.936 0.777

287 2.86 1.560 0.940 0.780

288 2.87 1.567 0.944 0.783

289 2.88 1.573 0.948 0.787

calc pt
361937360.xls
30 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

290 2.89 1.580 0.952 0.790

291 2.90 1.587 0.956 0.793

292 2.91 1.594 0.960 0.797

293 2.92 1.600 0.964 0.800

294 2.93 1.607 0.968 0.804

295 2.94 1.614 0.972 0.807

296 2.95 1.621 0.976 0.810

297 2.96 1.628 0.980 0.814

298 2.97 1.634 0.985 0.817

299 2.98 1.641 0.989 0.821

300 2.99 1.648 0.993 0.824

301 3.00 1.655 0.997 0.828

302 3.01 1.662 1.001 0.831

303 3.02 1.669 1.005 0.834

304 3.03 1.676 1.010 0.838

305 3.04 1.683 1.014 0.841

306 3.05 1.690 1.018 0.845

307 3.06 1.697 1.022 0.848

308 3.07 1.704 1.026 0.852

309 3.08 1.711 1.031 0.855

310 3.09 1.718 1.035 0.859

311 3.10 1.725 1.039 0.862

312 3.11 1.732 1.043 0.866

313 3.12 1.739 1.047 0.869

314 3.13 1.746 1.052 0.873

315 3.14 1.753 1.056 0.876

316 3.15 1.760 1.060 0.880

317 3.16 1.767 1.065 0.884

318 3.17 1.774 1.069 0.887

319 3.18 1.782 1.073 0.891

320 3.19 1.789 1.078 0.894

321 3.20 1.796 1.082 0.898

322 3.21 1.803 1.086 0.902

calc pt
361937360.xls
31 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

323 3.22 1.810 1.091 0.905

324 3.23 1.818 1.095 0.909

325 3.24 1.825 1.099 0.912

326 3.25 1.832 1.104 0.916

327 3.26 1.839 1.108 0.920

328 3.27 1.847 1.112 0.923

329 3.28 1.854 1.117 0.927

330 3.29 1.861 1.121 0.931

331 3.30 1.869 1.126 0.934

332 3.31 1.876 1.130 0.938

333 3.32 1.883 1.135 0.942

334 3.33 1.891 1.139 0.945

335 3.34 1.898 1.144 0.949

336 3.35 1.906 1.148 0.953

337 3.36 1.913 1.153 0.957

338 3.37 1.921 1.157 0.960

339 3.38 1.928 1.162 0.964

340 3.39 1.936 1.166 0.968

341 3.40 1.943 1.171 0.972

342 3.41 1.951 1.175 0.975

343 3.42 1.958 1.180 0.979

344 3.43 1.966 1.184 0.983

345 3.44 1.974 1.189 0.987

346 3.45 1.981 1.194 0.991

347 3.46 1.989 1.198 0.994

348 3.47 1.997 1.203 0.998

349 3.48 2.004 1.207 1.002

350 3.49 2.012 1.212 1.006

351 3.50 2.020 1.217 1.010

352 3.51 2.027 1.221 1.014

353 3.52 2.035 1.226 1.018

354 3.53 2.043 1.231 1.021

355 3.54 2.051 1.235 1.025

calc pt
361937360.xls
32 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

356 3.55 2.059 1.240 1.029

357 3.56 2.067 1.245 1.033

358 3.57 2.074 1.250 1.037

359 3.58 2.082 1.254 1.041

360 3.59 2.090 1.259 1.045

361 3.60 2.098 1.264 1.049

362 3.61 2.106 1.269 1.053

363 3.62 2.114 1.274 1.057

364 3.63 2.122 1.278 1.061

365 3.64 2.130 1.283 1.065

366 3.65 2.138 1.288 1.069

367 3.66 2.146 1.293 1.073

368 3.67 2.154 1.298 1.077

369 3.68 2.162 1.303 1.081

370 3.69 2.171 1.308 1.085

371 3.70 2.179 1.313 1.089

372 3.71 2.187 1.317 1.094

373 3.72 2.195 1.322 1.098

374 3.73 2.203 1.327 1.102

375 3.74 2.212 1.332 1.106

376 3.75 2.220 1.337 1.110

377 3.76 2.228 1.342 1.114

378 3.77 2.237 1.347 1.118

379 3.78 2.245 1.352 1.123

380 3.79 2.253 1.357 1.127

381 3.80 2.262 1.363 1.131

382 3.81 2.270 1.368 1.135

383 3.82 2.279 1.373 1.139

384 3.83 2.287 1.378 1.144

385 3.84 2.296 1.383 1.148

386 3.85 2.304 1.388 1.152

387 3.86 2.313 1.393 1.156

388 3.87 2.322 1.399 1.161

calc pt
361937360.xls
33 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

389 3.88 2.330 1.404 1.165

390 3.89 2.339 1.409 1.169

391 3.90 2.348 1.414 1.174

392 3.91 2.356 1.419 1.178

393 3.92 2.365 1.425 1.183

394 3.93 2.374 1.430 1.187

395 3.94 2.383 1.435 1.191

396 3.95 2.391 1.441 1.196

397 3.96 2.400 1.446 1.200

398 3.97 2.409 1.451 1.205

399 3.98 2.418 1.457 1.209

400 3.99 2.427 1.462 1.214

401 4.00 2.436 1.468 1.218

402 4.01 2.445 1.473 1.223

403 4.02 2.454 1.478 1.227

404 4.03 2.463 1.484 1.232

405 4.04 2.472 1.489 1.236

406 4.05 2.482 1.495 1.241

407 4.06 2.491 1.500 1.245

408 4.07 2.500 1.506 1.250

409 4.08 2.509 1.512 1.255

410 4.09 2.519 1.517 1.259

411 4.10 2.528 1.523 1.264

412 4.11 2.537 1.528 1.269

413 4.12 2.547 1.534 1.273

414 4.13 2.556 1.540 1.278

415 4.14 2.566 1.546 1.283

416 4.15 2.575 1.551 1.288

417 4.16 2.585 1.557 1.292

418 4.17 2.594 1.563 1.297

419 4.18 2.604 1.569 1.302

420 4.19 2.614 1.574 1.307

421 4.20 2.623 1.580 1.312

calc pt
361937360.xls
34 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

422 4.21 2.633 1.586 1.317

423 4.22 2.643 1.592 1.321

424 4.23 2.653 1.598 1.326

425 4.24 2.663 1.604 1.331

426 4.25 2.672 1.610 1.336

427 4.26 2.682 1.616 1.341

428 4.27 2.692 1.622 1.346

429 4.28 2.702 1.628 1.351

430 4.29 2.713 1.634 1.356

431 4.30 2.723 1.640 1.361

432 4.31 2.733 1.646 1.366

433 4.32 2.743 1.652 1.372

434 4.33 2.753 1.659 1.377

435 4.34 2.764 1.665 1.382

436 4.35 2.774 1.671 1.387

437 4.36 2.784 1.677 1.392

438 4.37 2.795 1.684 1.397

439 4.38 2.805 1.690 1.403

440 4.39 2.816 1.696 1.408

441 4.40 2.827 1.703 1.413

442 4.41 2.837 1.709 1.419

443 4.42 2.848 1.716 1.424

444 4.43 2.859 1.722 1.429

445 4.44 2.870 1.729 1.435

446 4.45 2.881 1.735 1.440

447 4.46 2.892 1.742 1.446

448 4.47 2.903 1.749 1.451

449 4.48 2.914 1.755 1.457

450 4.49 2.925 1.762 1.462

451 4.50 2.936 1.769 1.468

452 4.51 2.947 1.775 1.474

453 4.52 2.958 1.782 1.479

454 4.53 2.970 1.789 1.485

calc pt
361937360.xls
35 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

455 4.54 2.981 1.796 1.491

456 4.55 2.993 1.803 1.496

457 4.56 3.004 1.810 1.502

458 4.57 3.016 1.817 1.508

459 4.58 3.028 1.824 1.514

460 4.59 3.040 1.831 1.520

461 4.60 3.051 1.838 1.526

462 4.61 3.063 1.845 1.532

463 4.62 3.075 1.853 1.538

464 4.63 3.087 1.860 1.544

465 4.64 3.100 1.867 1.550

466 4.65 3.112 1.875 1.556

467 4.66 3.124 1.882 1.562

468 4.67 3.137 1.889 1.568

469 4.68 3.149 1.897 1.575

470 4.69 3.162 1.905 1.581

471 4.70 3.174 1.912 1.587

472 4.71 3.187 1.920 1.594

473 4.72 3.200 1.928 1.600

474 4.73 3.213 1.935 1.606

475 4.74 3.226 1.943 1.613

476 4.75 3.239 1.951 1.619

477 4.76 3.252 1.959 1.626

478 4.77 3.266 1.967 1.633

479 4.78 3.279 1.975 1.639

480 4.79 3.293 1.983 1.646

481 4.80 3.306 1.992 1.653

482 4.81 3.320 2.000 1.660

483 4.82 3.334 2.008 1.667

484 4.83 3.348 2.017 1.674

485 4.84 3.362 2.025 1.681

486 4.85 3.376 2.034 1.688

487 4.86 3.391 2.043 1.695

calc pt
361937360.xls
36 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

488 4.87 3.405 2.051 1.703

489 4.88 3.420 2.060 1.710

490 4.89 3.434 2.069 1.717

491 4.90 3.449 2.078 1.725

492 4.91 3.464 2.087 1.732

493 4.92 3.480 2.096 1.740

494 4.93 3.495 2.105 1.748

495 4.94 3.511 2.115 1.755

496 4.95 3.526 2.124 1.763

497 4.96 3.542 2.134 1.771

498 4.97 3.558 2.144 1.779

499 4.98 3.575 2.153 1.787

500 4.99 3.591 2.163 1.795

501 5.00 3.608 2.173 1.804

502 5.01 3.624 2.183 1.812

503 5.02 3.641 2.194 1.821

504 5.03 3.659 2.204 1.829

505 5.04 3.676 2.215 1.838

506 5.05 3.694 2.225 1.847

507 5.06 3.712 2.236 1.856

508 5.07 3.730 2.247 1.865

509 5.08 3.749 2.258 1.874

510 5.09 3.768 2.270 1.884

511 5.10 3.787 2.281 1.893

512 5.11 3.806 2.293 1.903

513 5.12 3.826 2.305 1.913

514 5.13 3.846 2.317 1.923

515 5.14 3.866 2.329 1.933

516 5.15 3.887 2.342 1.944

517 5.16 3.908 2.354 1.954

518 5.17 3.930 2.368 1.965

519 5.18 3.952 2.381 1.976

520 5.19 3.975 2.394 1.987

calc pt
361937360.xls
37 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

521 5.20 3.998 2.408 1.999

522 5.21 4.022 2.423 2.011

523 5.22 4.046 2.437 2.023

524 5.23 4.071 2.452 2.035

525 5.24 4.097 2.468 2.048

526 5.25 4.123 2.484 2.062

527 5.26 4.150 2.500 2.075

528 5.27 4.179 2.517 2.089

529 5.28 4.208 2.535 2.104

530 5.29 4.238 2.553 2.119

531 5.30 4.270 2.572 2.135

532 5.31 4.303 2.592 2.152

533 5.32 4.338 2.613 2.169

534 5.33 4.375 2.636 2.188

535 5.34 4.415 2.659 2.207

536 5.35 4.457 2.685 2.229

537 5.36 4.503 2.713 2.252

538 5.37 4.555 2.744 2.277

539 5.38 4.613 2.779 2.307

540 5.39 4.683 2.821 2.341

541 5.40 4.776 2.877 2.388

542 5.41 Err:502 Err:502 Err:502

543 5.42 Err:502 Err:502 Err:502

544 5.43 Err:502 Err:502 Err:502

545 5.44 Err:502 Err:502 Err:502

546 5.45 Err:502 Err:502 Err:502

547 5.46 Err:502 Err:502 Err:502

548 5.47 Err:502 Err:502 Err:502

549 5.48 Err:502 Err:502 Err:502

550 5.49 Err:502 Err:502 Err:502

551 5.50 Err:502 Err:502 Err:502

552 5.51 Err:502 Err:502 Err:502

553 5.52 Err:502 Err:502 Err:502

calc pt
361937360.xls
38 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

554 5.53 Err:502 Err:502 Err:502

555 5.54 Err:502 Err:502 Err:502

556 5.55 Err:502 Err:502 Err:502

557 5.56 Err:502 Err:502 Err:502

558 5.57 Err:502 Err:502 Err:502

559 5.58 Err:502 Err:502 Err:502

560 5.59 Err:502 Err:502 Err:502

561 5.60 Err:502 Err:502 Err:502

562 5.61 Err:502 Err:502 Err:502

563 5.62 Err:502 Err:502 Err:502

564 5.63 Err:502 Err:502 Err:502

565 5.64 Err:502 Err:502 Err:502

566 5.65 Err:502 Err:502 Err:502

567 5.66 Err:502 Err:502 Err:502

568 5.67 Err:502 Err:502 Err:502

569 5.68 Err:502 Err:502 Err:502

570 5.69 Err:502 Err:502 Err:502

571 5.70 Err:502 Err:502 Err:502

572 5.71 Err:502 Err:502 Err:502

573 5.72 Err:502 Err:502 Err:502

574 5.73 Err:502 Err:502 Err:502

575 5.74 Err:502 Err:502 Err:502

576 5.75 Err:502 Err:502 Err:502

577 5.76 Err:502 Err:502 Err:502

578 5.77 Err:502 Err:502 Err:502

579 5.78 Err:502 Err:502 Err:502

580 5.79 Err:502 Err:502 Err:502

581 5.80 Err:502 Err:502 Err:502

582 5.81 Err:502 Err:502 Err:502

583 5.82 Err:502 Err:502 Err:502

584 5.83 Err:502 Err:502 Err:502

585 5.84 Err:502 Err:502 Err:502

586 5.85 Err:502 Err:502 Err:502

calc pt
361937360.xls
39 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

587 5.86 Err:502 Err:502 Err:502

588 5.87 Err:502 Err:502 Err:502

589 5.88 Err:502 Err:502 Err:502

590 5.89 Err:502 Err:502 Err:502

591 5.90 Err:502 Err:502 Err:502

592 5.91 Err:502 Err:502 Err:502

593 5.92 Err:502 Err:502 Err:502

594 5.93 Err:502 Err:502 Err:502

595 5.94 Err:502 Err:502 Err:502

596 5.95 Err:502 Err:502 Err:502

597 5.96 Err:502 Err:502 Err:502

598 5.97 Err:502 Err:502 Err:502

599 5.98 Err:502 Err:502 Err:502

600 5.99 Err:502 Err:502 Err:502

601 6.00 Err:502 Err:502 Err:502

602 6.01 Err:502 Err:502 Err:502

603 6.02 Err:502 Err:502 Err:502

604 6.03 Err:502 Err:502 Err:502

605 6.04 Err:502 Err:502 Err:502

606 6.05 Err:502 Err:502 Err:502

607 6.06 Err:502 Err:502 Err:502

608 6.07 Err:502 Err:502 Err:502

609 6.08 Err:502 Err:502 Err:502

610 6.09 Err:502 Err:502 Err:502

611 6.10 Err:502 Err:502 Err:502

612 6.11 Err:502 Err:502 Err:502

613 6.12 Err:502 Err:502 Err:502

614 6.13 Err:502 Err:502 Err:502

615 6.14 Err:502 Err:502 Err:502

616 6.15 Err:502 Err:502 Err:502

617 6.16 Err:502 Err:502 Err:502

618 6.17 Err:502 Err:502 Err:502

619 6.18 Err:502 Err:502 Err:502

calc pt
361937360.xls
40 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

620 6.19 Err:502 Err:502 Err:502

621 6.20 Err:502 Err:502 Err:502

622 6.21 Err:502 Err:502 Err:502

623 6.22 Err:502 Err:502 Err:502

624 6.23 Err:502 Err:502 Err:502

625 6.24 Err:502 Err:502 Err:502

626 6.25 Err:502 Err:502 Err:502

627 6.26 Err:502 Err:502 Err:502

628 6.27 Err:502 Err:502 Err:502

629 6.28 Err:502 Err:502 Err:502

630 6.29 Err:502 Err:502 Err:502

631 6.30 Err:502 Err:502 Err:502

632 6.31 Err:502 Err:502 Err:502

633 6.32 Err:502 Err:502 Err:502

634 6.33 Err:502 Err:502 Err:502

635 6.34 Err:502 Err:502 Err:502

636 6.35 Err:502 Err:502 Err:502

637 6.36 Err:502 Err:502 Err:502

638 6.37 Err:502 Err:502 Err:502

639 6.38 Err:502 Err:502 Err:502

640 6.39 Err:502 Err:502 Err:502

641 6.40 Err:502 Err:502 Err:502

642 6.41 Err:502 Err:502 Err:502

643 6.42 Err:502 Err:502 Err:502

644 6.43 Err:502 Err:502 Err:502

645 6.44 Err:502 Err:502 Err:502

646 6.45 Err:502 Err:502 Err:502

647 6.46 Err:502 Err:502 Err:502

648 6.47 Err:502 Err:502 Err:502

649 6.48 Err:502 Err:502 Err:502

650 6.49 Err:502 Err:502 Err:502

651 6.50 Err:502 Err:502 Err:502

652 6.51 Err:502 Err:502 Err:502

calc pt
361937360.xls
41 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

653 6.52 Err:502 Err:502 Err:502

654 6.53 Err:502 Err:502 Err:502

655 6.54 Err:502 Err:502 Err:502

656 6.55 Err:502 Err:502 Err:502

657 6.56 Err:502 Err:502 Err:502

658 6.57 Err:502 Err:502 Err:502

659 6.58 Err:502 Err:502 Err:502

660 6.59 Err:502 Err:502 Err:502

661 6.60 Err:502 Err:502 Err:502

662 6.61 Err:502 Err:502 Err:502

663 6.62 Err:502 Err:502 Err:502

664 6.63 Err:502 Err:502 Err:502

665 6.64 Err:502 Err:502 Err:502

666 6.65 Err:502 Err:502 Err:502

667 6.66 Err:502 Err:502 Err:502

668 6.67 Err:502 Err:502 Err:502

669 6.68 Err:502 Err:502 Err:502

670 6.69 Err:502 Err:502 Err:502

671 6.70 Err:502 Err:502 Err:502

672 6.71 Err:502 Err:502 Err:502

673 6.72 Err:502 Err:502 Err:502

674 6.73 Err:502 Err:502 Err:502

675 6.74 Err:502 Err:502 Err:502

676 6.75 Err:502 Err:502 Err:502

677 6.76 Err:502 Err:502 Err:502

678 6.77 Err:502 Err:502 Err:502

679 6.78 Err:502 Err:502 Err:502

680 6.79 Err:502 Err:502 Err:502

681 6.80 Err:502 Err:502 Err:502

682 6.81 Err:502 Err:502 Err:502

683 6.82 Err:502 Err:502 Err:502

684 6.83 Err:502 Err:502 Err:502

685 6.84 Err:502 Err:502 Err:502

calc pt
361937360.xls
42 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

686 6.85 Err:502 Err:502 Err:502

687 6.86 Err:502 Err:502 Err:502

688 6.87 Err:502 Err:502 Err:502

689 6.88 Err:502 Err:502 Err:502

690 6.89 Err:502 Err:502 Err:502

691 6.90 Err:502 Err:502 Err:502

692 6.91 Err:502 Err:502 Err:502

693 6.92 Err:502 Err:502 Err:502

694 6.93 Err:502 Err:502 Err:502

695 6.94 Err:502 Err:502 Err:502

696 6.95 Err:502 Err:502 Err:502

697 6.96 Err:502 Err:502 Err:502

698 6.97 Err:502 Err:502 Err:502

699 6.98 Err:502 Err:502 Err:502

700 6.99 Err:502 Err:502 Err:502

701 7.00 Err:502 Err:502 Err:502

702 7.01 Err:502 Err:502 Err:502

703 7.02 Err:502 Err:502 Err:502

704 7.03 Err:502 Err:502 Err:502

705 7.04 Err:502 Err:502 Err:502

706 7.05 Err:502 Err:502 Err:502

707 7.06 Err:502 Err:502 Err:502

708 7.07 Err:502 Err:502 Err:502

709 7.08 Err:502 Err:502 Err:502

710 7.09 Err:502 Err:502 Err:502

711 7.10 Err:502 Err:502 Err:502

712 7.11 Err:502 Err:502 Err:502

713 7.12 Err:502 Err:502 Err:502

714 7.13 Err:502 Err:502 Err:502

715 7.14 Err:502 Err:502 Err:502

716 7.15 Err:502 Err:502 Err:502

717 7.16 Err:502 Err:502 Err:502

718 7.17 Err:502 Err:502 Err:502

calc pt
361937360.xls
43 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

719 7.18 Err:502 Err:502 Err:502

720 7.19 Err:502 Err:502 Err:502

721 7.20 Err:502 Err:502 Err:502

722 7.21 Err:502 Err:502 Err:502

723 7.22 Err:502 Err:502 Err:502

724 7.23 Err:502 Err:502 Err:502

725 7.24 Err:502 Err:502 Err:502

726 7.25 Err:502 Err:502 Err:502

727 7.26 Err:502 Err:502 Err:502

728 7.27 Err:502 Err:502 Err:502

729 7.28 Err:502 Err:502 Err:502

730 7.29 Err:502 Err:502 Err:502

731 7.30 Err:502 Err:502 Err:502

732 7.31 Err:502 Err:502 Err:502

733 7.32 Err:502 Err:502 Err:502

734 7.33 Err:502 Err:502 Err:502

735 7.34 Err:502 Err:502 Err:502

736 7.35 Err:502 Err:502 Err:502

737 7.36 Err:502 Err:502 Err:502

738 7.37 Err:502 Err:502 Err:502

739 7.38 Err:502 Err:502 Err:502

740 7.39 Err:502 Err:502 Err:502

741 7.40 Err:502 Err:502 Err:502

742 7.41 Err:502 Err:502 Err:502

743 7.42 Err:502 Err:502 Err:502

744 7.43 Err:502 Err:502 Err:502

745 7.44 Err:502 Err:502 Err:502

746 7.45 Err:502 Err:502 Err:502

747 7.46 Err:502 Err:502 Err:502

748 7.47 Err:502 Err:502 Err:502

749 7.48 Err:502 Err:502 Err:502

750 7.49 Err:502 Err:502 Err:502

751 7.50 Err:502 Err:502 Err:502

calc pt
361937360.xls
44 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

752 7.51 Err:502 Err:502 Err:502

753 7.52 Err:502 Err:502 Err:502

754 7.53 Err:502 Err:502 Err:502

755 7.54 Err:502 Err:502 Err:502

756 7.55 Err:502 Err:502 Err:502

757 7.56 Err:502 Err:502 Err:502

758 7.57 Err:502 Err:502 Err:502

759 7.58 Err:502 Err:502 Err:502

760 7.59 Err:502 Err:502 Err:502

761 7.60 Err:502 Err:502 Err:502

762 7.61 Err:502 Err:502 Err:502

763 7.62 Err:502 Err:502 Err:502

764 7.63 Err:502 Err:502 Err:502

765 7.64 Err:502 Err:502 Err:502

766 7.65 Err:502 Err:502 Err:502

767 7.66 Err:502 Err:502 Err:502

768 7.67 Err:502 Err:502 Err:502

769 7.68 Err:502 Err:502 Err:502

770 7.69 Err:502 Err:502 Err:502

771 7.70 Err:502 Err:502 Err:502

772 7.71 Err:502 Err:502 Err:502

773 7.72 Err:502 Err:502 Err:502

774 7.73 Err:502 Err:502 Err:502

775 7.74 Err:502 Err:502 Err:502

776 7.75 Err:502 Err:502 Err:502

777 7.76 Err:502 Err:502 Err:502

778 7.77 Err:502 Err:502 Err:502

779 7.78 Err:502 Err:502 Err:502

780 7.79 Err:502 Err:502 Err:502

781 7.80 Err:502 Err:502 Err:502

782 7.81 Err:502 Err:502 Err:502

783 7.82 Err:502 Err:502 Err:502

784 7.83 Err:502 Err:502 Err:502

calc pt
361937360.xls
45 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

785 7.84 Err:502 Err:502 Err:502

786 7.85 Err:502 Err:502 Err:502

787 7.86 Err:502 Err:502 Err:502

788 7.87 Err:502 Err:502 Err:502

789 7.88 Err:502 Err:502 Err:502

790 7.89 Err:502 Err:502 Err:502

791 7.90 Err:502 Err:502 Err:502

792 7.91 Err:502 Err:502 Err:502

793 7.92 Err:502 Err:502 Err:502

794 7.93 Err:502 Err:502 Err:502

795 7.94 Err:502 Err:502 Err:502

796 7.95 Err:502 Err:502 Err:502

797 7.96 Err:502 Err:502 Err:502

798 7.97 Err:502 Err:502 Err:502

799 7.98 Err:502 Err:502 Err:502

800 7.99 Err:502 Err:502 Err:502

801 8.00 Err:502 Err:502 Err:502

802 8.01 Err:502 Err:502 Err:502

803 8.02 Err:502 Err:502 Err:502

804 8.03 Err:502 Err:502 Err:502

805 8.04 Err:502 Err:502 Err:502

806 8.05 Err:502 Err:502 Err:502

807 8.06 Err:502 Err:502 Err:502

808 8.07 Err:502 Err:502 Err:502

809 8.08 Err:502 Err:502 Err:502

810 8.09 Err:502 Err:502 Err:502

811 8.10 Err:502 Err:502 Err:502

812 8.11 Err:502 Err:502 Err:502

813 8.12 Err:502 Err:502 Err:502

814 8.13 Err:502 Err:502 Err:502

815 8.14 Err:502 Err:502 Err:502

816 8.15 Err:502 Err:502 Err:502

817 8.16 Err:502 Err:502 Err:502

calc pt
361937360.xls
46 of 48 | DESIGNED BY |
STANDARD TITLE: REINFORCEMENT PERCENTAGE, pt FOR FLEXURE MEMBERS

FOR SINGLY REINFORCED SECTIONS

STANDARD NO.:

818 8.17 Err:502 Err:502 Err:502

819 8.18 Err:502 Err:502 Err:502

calc pt
361937360.xls
47 of 48 | DESIGNED BY |
calc pt
361937360.xls
48 of 48 | DESIGNED BY |