Syllabus For J e Civil Under PWD

SYLLABUS FOR COMPETITIVE EXAMINATION FOR THE POST OF
JUNIOR ENGINEER (CIVIL)

UNDER PUBLIC WORKS DEPARTMENT, GOVERNMENT OF MIZORAM, 2016
SUBJECTS
(a) General English (Conventional / Objective Type) ........................................... 100 Marks

(b) Technical Paper - I (MCQ/Objective Type) ...................................................... 150 Marks
(c) Technical Paper - II (MCQ/Objective Type)..................................................... 150 Marks
**********
GENERAL ENGLISH
(Full Marks : 100)
(a) Essay Writing (Conventional) .................................................................... 20 Marks

(b) Idioms & Phrases (Objective Type) ........................................................... 16 Marks
(c) Comprehension of given passages (Objective Type) ................................. 16 Marks
(d) Grammar (Objective Type) ....................................................................... 16 Marks
Parts of Speech : Nouns, Adjective, Verb, Adverb, Preposition, etc.
(e) Composition (Objective Type)................................................................... 16 Marks
i) Analysis of complex and compound sentences
ii) Transformation of sentences
iii) Synthesis of sentences
(f) Correct usage and vocabularies (Objective Type) ...................................... 16 Marks
**********
SYLLABUS FOR JUNIOR ENGINEER EXAMINATION
UNDER PUBLIC WORKS DEPARTMENT
CIVIL ENGINEERING
PAPER-I (150 marks)
1.Building Materials (30 Marks)
Physical and Chemical properties, Classification, Standard Tests, Uses and

Types of materials:- Building stones, Bricks, silicate based materials, Cement
and Mortars, Sand, Aggregates, Asbestos products, Timber and Wood based
Products, Paints, Varnishes, Ferrous metals, Lubricants, Sealants for joints,
Polymers and Plastics, Protective and decorative coatings.
2.Soil Mechanics and Foundation Engineering (30 Marks)
Origin of soil, phase diagram, Definitions- void ratio, porosity, degree of

saturation, water content, specific gravity of soil grains, unit weights, density
index and interrelationship of different parameters, Grain size distribution
curves and their uses. Index properties of soils, Atterberg's limits, ISI soil
classification and plasticity chart. Permeability of soil, coefficient of
permeability, determination of coefficient of permeability, Shear strength of
soils, direct shear test, Vane shear test, Triaxial test. Soil compaction,
Laboratory compaction test, Maximum dry density and optimum moisture
content, earth pressure theories, active and passive earth pressures, Bearing
capacity of soils, plate load test, standard penetration test.
Foundation engineering:-Foundation classification, Different type and selection

criteria of foundation type, Requirements for a stable foundation, Minimum
depth for shallow foundation, Definitions of bearing capacity of soil, Type of
failure of soil below foundation footing, Determination of size of foundation
footings.
3. Hydrology and Rainwater harvesting- (30 Marks)
Hydrological cycle, Water budget equation, Precipitation :- forms,

characteristics of precipitation on india, measurement, losses from precipitation.
Run-off :- hydrograph, characteristics of streams, yield, droughts, surface water
resources of india. Ground water :- forms, aquifer properties, geological
formations as aquifers. Wells, Well losses, Specific capacity, Ground water
capacity.
Rainwater harvesting:-Definition of terms :- aquifer, artificial recharge, bore
well, dry well, open wells, water table. Components of roof top rainwater
harvesting and conservation system. Calculation of amount of rainwater that can
be harvested from roof top. Design parameters for settlement tanks. General
recommendations for rainwater harvesting. Quality of rainwater and method of
treatment.
4.Design of RCC Building members and RCC water tanks (30 Marks)
Principles of Limit state method (LSM) and Working stress method of design,
Provisions of IS:456 and IS:13920 (Latest version) :-
-Materials, workmanship, inspection, testing, placing and requirement of
reinforcement, requirement of cement, aggregates and water. Water/Cement
ration. Characteristic load & Strength, Partial factor of safety, Stress-strain
characteristic of concrete and steel, Limit state of Durability, limit state of
collapse in flexure and shear, limit state of serviceability. Theory and design of
singly reinforced members. Bond, anchorage, development length and splicing.
Design and IS code provisions for short columns, one way and two way slabs,
isolated footing.
RCC water tanks :- Indian standard codes and provisions prescribed for
designing water retaining structures, causes and control of cracking, joints in
water retaining structures. Removal of formworks/shutters. Lining, lighting
protection and ventilation of water tanks. Regular capacity and design capacity
of water tanks. Classification and layout of elevated tanks. Nomenclature and
functions of ancillary items of water retaining structures. Components of water
retaining structures.
5.Protective works, Slope stability and Landslide correction (30 Marks)
Design, construction, specifications and uses of Retaining walls, Breast walls,

Toe walls, Crib walls and Revetment walls. Classification of slope movement.
Causes of slope movement. Landslide investigations. Stability analysis,
corrective measures and design considerations
CIVIL ENGINEERING
PAPER-II (150 marks)
1.Estimating, Costing and Valuation (30 Marks)
Estimate, Glossary of technical terms, Analysis of rates, Methods and unit of

measurement, Items of work Earthwork, Brick work (Modular & Traditional
bricks), RCC work, Shuttering, Timber work, Painting, Flooring, Plastering.
Boundary wall, Brick building, Water Tank, Septic tank, Bar bending schedule.
Centre line method, Mid-section formula, Trapezodial formula, Simpsons rule.
Cost estimate of Septic tank, flexible pavements, Tube well, isolated and
combined footings, Steel Truss, Piles and pile-caps. Valuation Value and cost,
scrap value, salvage value, assessed value, sinking fund, depreciation and
obsolescence, methods of valuation.
2.Transportation Engineering and Surveying (30 Marks)
Highway Engineering cross sectional elements, geometric design, types of

pavements, pavement materials aggregates and bitumen, different tests,
Construction and specifications of : Granular Sub-Base (GSB), Water Bound
Macadam (WBM) and Wet Mix Macadam (WMM), Gravel Road, Bituminous
construction. Rigid pavement joint, Type of pavement distresses and
maintenance. Highway drainage. Traffic Engineering : Traffic signals, traffic
operation, traffic signs and markings, road safety.
Surveying: Principles of surveying, measurement of distance, chain surveying,

working of prismatic compass, compass traversing, bearings, local attraction,
plane table surveying, theodolite traversing, adjustment of theodolite, Levelling,
Definition of terms used in leveling, contouring, curvature and refraction
corrections, temporary and permanent adjustments of dumpy level, methods of
contouring, uses of contour map, tachometric survey, curve setting, earth work
calculation, advanced surveying equipment.
3.Environmental Engineering (20 Marks)
Quality of water, source of water supply, purification of water, distribution of

water, need of sanitation, sewerage systems, circular sewer, oval sewer, sewer
appurtenances, sewage treatments. Surface water drainage. Solid waste
management types, effects, engineered management system. Air pollution
pollutants, causes, effects, control. Noise pollution causes, health effects,
control.
4.Design of Steel structures and Steel water tanks (30 Marks)
Riveted and Bolted joints :- types and definitions. Riveted joints :- assumptions
in the theory. Failures, strength and efficiency. Design of riveted joints for
axially loaded members. Welded joints :- processes, types and symbols,
advantages and disadvantages. Terms used in the design of fillet welds and butt
welds. Compression members :- effective length, maximum slenderness ratio,
typical cross-section, design of compression members.
Steel tanks :- Types of steel tanks commonly used, accessories commonly

required, pressed steel tanks.
5.Professional practices (20 Marks)
Schedule of works, Schedule of rates (SOR), Analysis of rates, Technical

specifications, Cost indices. Stages for execution of works :- administrative
approval, expenditure sanction, technical sanction, deviations, extra and
substituted items, contingencies, work charged establishment, Types of
estimate. Tendering and Agreement :- sale, opening and acceptance of tenders,
earnest money, performance guarantee, security deposit, extension of time,
liquidated damage, advance payment to contractors. Measurement book :-
writing, recording, testing of measurement, loss of measurement book.
Contract :- definition, essential elements of a valid contract, offer and

acceptance. Free consent (Definition and consequences) :- coercion, undue
influence, fraud, mis-representation, mistake. Special contracts :- indemnity,
guarantee, bailment and pledge, agency.
6. Aptitude Test (20 Marks)
(a) Numerical And Figurework Tests: (4 Marks)

These tests are reflections of fluency with numbers and
calculations. It shows how easily a person can think with
numbers. The subject will be given a series of numbers.
His/Her task is to see how the numbers go together to form a
relationship with each other. He/She has to choose a number
which would go next in the series.
(b) Verbal Analysis And Vocabulary Tests: (6 Marks)
These tests measure the degree of comfort and fluency with the
English language. These tests will measure how a person will
reason with words. The subject will be given questions with
alternative answers, that will reflect his/her command of the rule
and use of English language.
(c) Visual And Spatial/3-D Ability Tests: (4 Marks)
These tests are used to measure perceptual speed and acuity.
The subject will be shown pictures where he/she is asked to
identify the odd one out; or which comes next in the sequence or
explores how easily he/she can see and turn around objects in
space.
(d) Abstract Reasoning Tests: (6 Marks)
This test measures the ability to analyse information and solve problems
on a complex, thought based level. It measures a persons ability to quickly
identify patterns, logical rules and trends in new data, integrate this information,
and apply it to solve problems.

Syllabus For J e Civil Under PWD

Uploaded by

Copyright:

Available Formats

Syllabus For J e Civil Under PWD

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Syllabus For J e Civil Under PWD

Uploaded by

Copyright:

Available Formats

SYLLABUS FOR COMPETITIVE EXAMINATION FOR THE POST OF

JUNIOR ENGINEER (CIVIL)

(a) General English (Conventional / Objective Type) ........................................... 100 Marks

(Full Marks : 100)

(a) Essay Writing (Conventional) .................................................................... 20 Marks

1.Building Materials (30 Marks)

Physical and Chemical properties, Classification, Standard Tests, Uses and

2.Soil Mechanics and Foundation Engineering (30 Marks)

Origin of soil, phase diagram, Definitions- void ratio, porosity, degree of

Foundation engineering:-Foundation classification, Different type and selection

3. Hydrology and Rainwater harvesting- (30 Marks)

Hydrological cycle, Water budget equation, Precipitation :- forms,

5.Protective works, Slope stability and Landslide correction (30 Marks)

Design, construction, specifications and uses of Retaining walls, Breast walls,

1.Estimating, Costing and Valuation (30 Marks)

Estimate, Glossary of technical terms, Analysis of rates, Methods and unit of

2.Transportation Engineering and Surveying (30 Marks)

Highway Engineering cross sectional elements, geometric design, types of

Surveying: Principles of surveying, measurement of distance, chain surveying,

3.Environmental Engineering (20 Marks)

Quality of water, source of water supply, purification of water, distribution of

Steel tanks :- Types of steel tanks commonly used, accessories commonly

5.Professional practices (20 Marks)

Schedule of works, Schedule of rates (SOR), Analysis of rates, Technical

Contract :- definition, essential elements of a valid contract, offer and

6. Aptitude Test (20 Marks)

(a) Numerical And Figurework Tests: (4 Marks)

You might also like