Hardware Manual - Rel 2 - 20

VTWIN
Hardware Manual
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

ESA elettronica S.P.A. reserves the right to change
the information contained in this document without
notice. The information represents no obligation on
the part of the company.
All products referred to are covered by the appropri-

ate trademark and/or copyright legislation.
i
Quality Assurance
ESA elettronicas quality control system has been certified by the CSQ,
EQNet and ITQS (certification N 9115.ESAE) as complying with UNI EN
ISO 9001:2000 standards.
These represent the most comprehensive set of standards within the interna-
tional framework of ISO and cover every aspect of the life-cycle of the
product (planning, development, production, installation and customer
care).
All the products described in this manual comply with the following
standards:
electromagnetic compatibility (EMC):
emissions EN 61000-6-4 (2001)

immunity EN 61000-6-2 (2001)
and thus are in line with:
Council Directives
89/336/EEC 92/31/EEC 93/68/EEC
Products bearing the mark cULus have been certified in compliance with
UL 508 and CSA C22.2 N14-M95 safety standards.
Video terminals VT50 and VT60 have also obtained:
RINA Approval
Registro Navale Italiano
No. ELE/797/1
DNV certification
Det Norske Veritas
Certificate No. A-9044
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

ii
Table 0.1: Tests carried out for CE-mark.

Immunity Disturbance characteristics Standard
Electrostatic discharge: EN61000-4-2
Contact 4kV
Air 8kV
ENV50140/ENV50141
Radio-Frequency
10 V/m
To disturbances
Rapid transitories: EN61000-4-4
Power supply 2 kV
I/O serial 1 kV
Impulsive transitories Common and
EN61000-4-5
Differential mode
To radio EN55011
Emission
disturbances Level of radio disturbance B
Tests carried out for RINA approval
Publication IEC 68-2-6 (1982) Fc. test (Vibration)

Publication IEC 68-2-30 (1980) Db. test (Hot wet cycle)
Publication IEC 68-2-1/IEC 68-2-1A (1976) + A1 (1983) Ad-Amend-
ment n1 test (1983) (Cold)
Any modification made to the product in its original form as sold

by ESA or any installation not envisaged in this manual automati-
cally implies a cancellation of the products marks of approval. ESA
declines all responsibility in relation to its products where these have
undergone modification or been installed in ways not envisaged in this
manual.
The simple application of an adhesive on any part of the terminal

is considered to be a variation of the original product and thus
implies the annulment of the marks of approval.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

iii
General Safety Precautions
System The System should be designed to prevent equipment malfunction due to

Design communication faults between the VT and its host controller. This will
assure the protection of both personnel and equipment.
Do not use the VT as a warning device for critical alarms that can cause
operator injury, production stoppage or machine damage. Every critical
alarm indicator or control, must be designed using appropriate stand
alone hardware devices.
Redundant failsafe system design should be used in order to ensure

proper safety when the VT is used in special applications such as safety
equipment, non-life support medical devices, disaster prevention
devices, transportation vehicles, etc.
The VT is not suitable for applications such as medical life support

equipment, hazardous areas or any potentially explosive environments,
aerospace equipment, nuclear power control devices or aircraft control
devices. These kinds of applications require a higher level of safety and
reliability.
Installation Strictly follow the wiring diagram and grounding recommendations con-
and wiring tained in this document, in order to prevent any damaged to the VT or to
the connected devices.
Do not use any voltage beyond the VTs specified range in order to pre-
vent damage or electrical shock.
Make sure power to the unit is off before opening the VT for the calibra-
tion procedure described in this document.
Do not modify the VT for any reason. Doing this may result in electrical
shock or fire, in addition to loss of Certifications like CE or UL.
Use the proper torque shown on the label to tighten the terminal screws.
Excess tightening may cause short circuit, fire or device malfunction.
Do not install the VT in an ambient temperature exceeding the allowed

range. This may result in malfunction or shortened life of the unit.
Do not limit the VTs rear-face ventilation, in order to avoid component

overheating.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

iv
Usage Do not strike the touch panel with a hard or pointed object, or press on
the touch screen with excessive force. The actuating force is 50 grams
(1.8 oz.).
Do not allow liquids to enter the VT case. This can cause malfunction or
electrical shock.
Do not use the VT in excessively dirty or dusty environmental condi-

tions, and do not place it under direct sunlight.
Do not use the VT where strong jolting or excessive vibration can occur.
Do not use the VT where abrasive chemicals can evaporate or are present
in the air.
Use only allowed chemical substances to clean the VT (see Users Man-
ual chapter on cleaning).
Ensure that no metal debris falls into the VT. This can cause fire, mal-
function or incorrect device operation.
After turning the VT OFF, please wait at least 5 seconds before turning it
ON again, otherwise it may not start up correctly.
Be sure to perform regular back-ups of the VTs data to avoid loss due to
unexpected accidents to your system.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

v
Contents
Foreword The manual ................................................................... F-1

Its purpose .................................................................... F-1
Conventions .................................................................. F-1
Introduction What is a Video Terminal .............................................. I-1
Essential information Graphic terminals.................................................................. E-1

Graphic terminals - STN ....................................................... E-3
Graphic terminals - TFT........................................................ E-3
Graphic terminals Touch Screen .......................................... E-3
General information on Contents........................................................................ 1-1

electromagnetic Laying cables ................................................................ 1-2
compatibility (EMC) Shielding of cables ........................................................ 1-2
Earthing of shielding and electronic circuits .................. 1-2
Switching of capacitive loads ........................................ 1-2
Switching off inductive loads ......................................... 1-2
Disturbance suppression circuit - RC and DIODE ........ 1-3
Power Supply Contents........................................................................ 2-1

Connection pins ............................................................ 2-2
Wiring.................................................................................... 2-2
Connections to be avoided ........................................... 2-2
Recommended connection ........................................... 2-3
Video terminal VT50 Contents........................................................................ 3-1

Technical characteristics............................................... 3-2
Functions ...................................................................... 3-4
Front face ...................................................................... 3-8
Standard series rear view ............................................. 3-9
CAN series rear view .................................................... 3-10
Dimensions and Cut-out................................................ 3-11
Accessories .......................................................................... 3-12
Termination of CAN line........................................................ 3-12
Transfer PC -> VT................................................................. 3-12
Preparation for reception ...................................................... 3-13
Information relating to driver ................................................. 3-14
Adjusting the contrast on the display .................................... 3-14
Video terminal VT60 Contents........................................................................ 4-1

Functions ...................................................................... 4-4
Front view ..................................................................... 4-8
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CONTENTS
vi
Accessories .......................................................................... 4-12

Termination of CAN line ....................................................... 4-12
Transfer PC -> VT ................................................................ 4-12
Preparation for reception...................................................... 4-13
Information relating to driver................................................. 4-14
Adjusting the contrast on the display.................................... 4-15
Video terminal Contents........................................................................ 5-1

VT150W Technical characteristics............................................... 5-2
Functions....................................................................... 5-4
Front view...................................................................... 5-8
Customizing label ................................................................. 5-10
Accessories .......................................................................... 5-14
Transfer PC -> VT ................................................................ 5-15

Functions....................................................................... 6-4
Front view...................................................................... 6-8
Rear view ...................................................................... 6-11
Accessories .......................................................................... 6-13
Transfer PC -> VT ................................................................ 6-13

Functions....................................................................... 7-4
Front view...................................................................... 7-8
Rear view ...................................................................... 7-11
Accessories .......................................................................... 7-14
Transfer PC -> VT ................................................................ 7-14
Preparation for reception............................................... 7-15

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

vii
Functions ...................................................................... 8-4

Front view ..................................................................... 8-8
Rear view ...................................................................... 8-11
Accessories .......................................................................... 8-14
Transfer PC -> VT................................................................. 8-14
Preparation for reception .............................................. 8-15

Functions ...................................................................... 9-4
Front view ..................................................................... 9-8
Accessories .......................................................................... 9-14
Transfer PC -> VT................................................................. 9-15

Functions ...................................................................... 10-4
Front view ..................................................................... 10-8
Rear view ...................................................................... 10-11
Accessories .......................................................................... 10-14
Transfer PC -> VT................................................................. 10-14

Functions ...................................................................... 11-4
Front view ..................................................................... 11-8
Rear view ...................................................................... 11-11
Accessories .......................................................................... 11-13
Transfer PC -> VT................................................................. 11-13
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CONTENTS
viii
Improving display color quality ............................................. 11-19


Functions....................................................................... 12-4
Front view...................................................................... 12-8
Profibus-DP series rear view......................................... 12-10
Ethernet series rear view .............................................. 12-12
Accessories .......................................................................... 12-14
Methods of mounting............................................................ 12-14
Calibration of Touch Screen................................................. 12-15
Introducing the MAC address............................................... 12-18
Transfer PC -> VT ................................................................ 12-20
Information relating to driver ......................................... 12-22

Functions....................................................................... 13-4
Front view...................................................................... 13-8
Rear view ...................................................................... 13-11
Accessories .......................................................................... 13-13
Transfer PC -> VT ................................................................ 13-13

Functions....................................................................... 14-4
Front view...................................................................... 14-8
Accessories .......................................................................... 14-12
Methods of mounting............................................................ 14-12
Transfer PC -> VT ................................................................ 14-17
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

ix
Video terminal VT505H Contents........................................................................ 15-1

Functions ...................................................................... 15-5
Front view ..................................................................... 15-9
Rear view ...................................................................... 15-10
Accessories .......................................................................... 15-12
Connection cable .................................................................. 15-12
Adjusting holding strap for grip ............................................. 15-12
Calibration of Touch Screen ................................................. 15-12
Transfer PC -> VT................................................................. 15-15

Functions ...................................................................... 16-4
Front view ..................................................................... 16-8
Accessories .......................................................................... 16-13
Introducing the MAC address ............................................... 16-17
Transfer PC -> VT................................................................. 16-20

Functions ...................................................................... 17-4
Front view ..................................................................... 17-8
Accessories .......................................................................... 17-13
Transfer PC -> VT................................................................. 17-20
Video terminal VT525H Contents........................................................................ 18-1
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CONTENTS
x

Functions....................................................................... 18-5
Front view...................................................................... 18-9
Rear view ...................................................................... 18-10
Accessories .......................................................................... 18-12
Connection cable.................................................................. 18-12
Adjusting holding strap for grip............................................. 18-12
Transfer PC -> VT ................................................................ 18-15

Functions....................................................................... 19-4
Front view...................................................................... 19-8
Accessories .......................................................................... 19-14
Transfer PC -> VT ................................................................ 19-21

Functions....................................................................... 20-4
Front view...................................................................... 20-8
Accessories .......................................................................... 20-12
Transfer PC -> VT ................................................................ 20-13

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

xi
Functions ...................................................................... 21-4

Front view ..................................................................... 21-8
Rear view ...................................................................... 21-9
Accessories .......................................................................... 21-11
Transfer PC -> VT................................................................. 21-11
Improving display color quality.............................................. 21-18

Functions ...................................................................... 22-4
Front view ..................................................................... 22-8
Rear view ...................................................................... 22-9
Accessories .......................................................................... 22-11
Transfer PC -> VT................................................................. 22-11

Functions ...................................................................... 23-4
Front view ..................................................................... 23-8
Accessories .......................................................................... 23-14
Transfer PC -> VT................................................................. 23-21

Functions ...................................................................... 24-4
Front view ..................................................................... 24-8
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CONTENTS
xii

Accessories .......................................................................... 24-14
Transfer PC -> VT ................................................................ 24-21

Functions....................................................................... 25-4
Front view...................................................................... 25-8
Accessories .......................................................................... 25-13
Transfer PC -> VT ................................................................ 25-19

VT585WB Technical characteristics............................................... 26-2
Functions....................................................................... 26-4
Front view...................................................................... 26-8
Accessories .......................................................................... 26-14
Transfer PC -> VT ................................................................ 26-21

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

xiii
Functions ...................................................................... 27-4

Front view ..................................................................... 27-8
Accessories .......................................................................... 27-14
Transfer PC -> VT................................................................. 27-21
Inserting customized Contents........................................................................ 28-1

labels Label ..................................................................................... 28-2
Warnings............................................................................... 28-2
Notes .................................................................................... 28-4
Mounting the terminal Contents........................................................................ 29-1

within the container Using nuts ..................................................................... 29-2
Using hooks .................................................................. 29-3
Fixing using external support................................................ 29-6
Tightening the fixing screws ................................................. 29-10
Communication ports Contents........................................................................ 30-1

General notes ............................................................... 30-2
Necessary steps ........................................................... 30-2
MSP serial port ............................................................. 30-3
ASP serial port .............................................................. 30-4
ASP-15L serial port ....................................................... 30-5
ASP-9 serial port ........................................................... 30-6
ASP-8 serial port ........................................................... 30-6
LPT parallel port............................................................ 30-7
Ethernet port ................................................................. 30-8
Interbus-S port .............................................................. 30-9
Profibus-DP port ........................................................... 30-10
CAN port ....................................................................... 30-10
RS485 serial port .......................................................... 30-11
PC/VT serial port........................................................... 30-11
PC <-> VT connection................................................... 30-12
Settings for the Modem Contents........................................................................ 31-1

AT commands to be sent .............................................. 31-2
Sending commands .............................................................. 31-3
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CONTENTS
xiv
Connection cable for H Contents........................................................................ 32-1

Series terminals Standard series connection cable ........................................ 32-2
Standard series connections without VTHCB ...................... 32-3
Standard series connections with VTHCB ........................... 32-6
CAN series connection cable ............................................... 32-7
CAN series connections ....................................................... 32-7
Lay-out of button functions ................................................... 32-8

accessories 1/2AA Battery ................................................................ 33-4
Cell battery .................................................................... 33-4
Flash module........................................................................ 33-5
Fixing hook for Hand Held.................................................... 33-8
Interface for connecting Hand Held with MSP/ASP-15L ...... 33-9
Memory card ........................................................................ 33-13
Memory module.................................................................... 33-18
Integrated Interbus-S module............................................... 33-19
Integrated Profibus-DP module ............................................ 33-21
RS485 Serial module ........................................................... 33-21
Protfilm4/6/6H/10/12............................................................. 33-22
Interbus-S and Profibus-DP card ......................................... 33-27
Connection card for PC-NET................................................ 33-34
Adapter for external CAN network........................................ 33-37
20 key serial keyboard ......................................................... 33-42
Blank keyboard..................................................................... 33-46
Network connection Contents........................................................................ 34-1

Profibus-DP .......................................................................... 34-3
Profibus-DP (ESA profile): VT operation .............................. 34-4
Profibus-DP (ESA profile): Configuration software............... 34-4
Profibus-DP (ESA profile): Logical diagram ......................... 34-5
Profibus-DP (ESA profile): Physical diagram ....................... 34-6
Profibus-DP (Standard): VT operation ................................. 34-6
Profibus-DP (Standard): Configuration software .................. 34-6
Profibus-DP (Standard): Logical diagram............................. 34-7
Profibus-DP (Standard): Physical diagram........................... 34-7
Profibus-DP: Connection...................................................... 34-8
Interbus-S............................................................................. 34-10
Interbus-S: VT operation ...................................................... 34-10
Interbus-S: Configuration software....................................... 34-10
Interbus-S: Logical diagram ................................................. 34-11
Interbus-S: Physical diagram ............................................... 34-12
Interbus-S: Connection......................................................... 34-12
ESA-Net ............................................................................... 34-14
ESA-Net: VT operation......................................................... 34-14
ESA-Net: Connecting the terminals...................................... 34-16
ESA-Net: Configuration software ......................................... 34-20
ETHERNET .......................................................................... 34-21
ETHERNET: VT operation ................................................... 34-21
ETHERNET: Configuration software .................................... 34-21
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

xv
ETHERNET: Connections .................................................... 34-22

ETHERNET: Checking the connection ................................. 34-23
CAN ...................................................................................... 34-24
CAN: VT functioning in CAN network ................................... 34-24
CAN: Configuration software ................................................ 34-25
CAN: Connection .................................................................. 34-25
Operation of terminal Contents........................................................................ 35-1

with keyboard Changing value of variable field............................................ 35-2
Total change ......................................................................... 35-3
Partial change....................................................................... 35-3
Examples of varying fields .................................................... 35-3
Displaying messages............................................................ 35-8
Information messages .......................................................... 35-8
VT50 info-messages............................................................. 35-8
VT60 info-messages............................................................. 35-9
VT150W - VT160W info-messages ...................................... 35-10
VT170W info-messages ....................................................... 35-10
VT300W - VT310W - VT320W info-messages ..................... 35-12
ISA-1A alarms....................................................................... 35-16
VT170W alarms .................................................................... 35-17
VT190W alarms .................................................................... 35-19
VT300W - VT310W - VT320W alarms.................................. 35-20
VT330W alarms .................................................................... 35-23
ISA-1A alarm history buffer................................................... 35-24
VT170W history buffer .......................................................... 35-25
VT300W - VT310W - VT320W history buffer........................ 35-26
Help messages ..................................................................... 35-29
Operation of terminal Contents........................................................................ 36-1

with touch screen Changing value of variable field............................................ 36-2
Total change ......................................................................... 36-3
Partial change....................................................................... 36-3
Examples of varying fields .................................................... 36-3
Displaying messages............................................................ 36-19
Information messages .......................................................... 36-19
VT5xxH - VT1x5/505/515/525/555/56xW info-msgs............. 36-20
Vertical VT1x5W info-messages........................................... 36-21
VT575W - VT580W- VT585W - VT585WB info-messages . 36-22
ISA-1A alarms....................................................................... 36-24
VT525H - VT1x5/515/525/555/56xW alarms ........................ 36-25
Vertical VT1x5W alarms ....................................................... 36-27
VT575W - VT580W - VT585W - VT585WB alarms .............. 36-29
VT595W alarms .................................................................... 36-30
ISA-1A alarm history buffer................................................... 36-31
VT525H - VT1x5/515/525/555/56xW history buffer .............. 36-32
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CONTENTS
xvi
Vertical VT1x5W history buffer............................................. 36-32

VT575W - VT580W - VT585W - VT585WB history buffer.... 36-33
VT595W history buffer.......................................................... 36-33
Help messages..................................................................... 36-33
Help and information messages relating to alarms .............. 36-34
Help messages relating to project pages ............................. 36-35
Data exchange area Contents........................................................................ 37-1

Status area for the terminal .................................................. 37-3
Status area for internal LEDs ............................................... 37-8
Status area for external LEDs .............................................. 37-12
Status area for recipes ......................................................... 37-14
Status area for internal keys................................................. 37-15
Status area for external keys................................................ 37-23
Status area for internal keys (Real Time)............................. 37-25
Status area for external keys (Real Time)............................ 37-25
Status area for printer........................................................... 37-26
Status area for trends........................................................... 37-28
Command response area..................................................... 37-29
Command area external LEDs (fixed light) .......................... 37-30
Command area external LEDs (blinking light)...................... 37-31
Command area internal red LEDs (fixed light) ..................... 37-32
Command area internal red LEDs (blinking light)................. 37-33
Command area internal green LEDs (fixed light) ................. 37-34
Command area internal green LEDs (blinking light)............. 37-35
Command area..................................................................... 37-36
Communication Contents........................................................................ 38-1

protocols List of protocols ............................................................. 38-2
Free terminal protocol Contents........................................................................ 39-1

Free terminal protocol .......................................................... 39-2
Editing parameters for VT50 ......................................... 39-3
Editing parameters for VT60 ......................................... 39-4
Editing parameters for VT150/160W............................. 39-5
Free terminal control characters........................................... 39-6
Key codes for VT50.............................................................. 39-9
Key codes for VT60.............................................................. 39-9
Key codes for VT150/160W ............................................ 39-10
Code of External keys for MT1000 and VT160W................. 39-13
Free terminal in Network ...................................................... 39-14
Example of handling...................................................... 39-16
Connection cables Contents........................................................................ 40-1

General notes................................................................ 40-4
Connecting the cable shield .......................................... 40-5
MSP<->ASP conversion ............................................... 40-7
ELECTREX NETWORK ANALYZER............................ 40-8
ABB DRIVE ................................................................... 40-8
ALLEN-BRADLEY DRIVE............................................. 40-9
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

xvii
ATLAS COPCO DRIVE................................................. 40-10

BERGER-LAHR DRIVE ................................................ 40-11
CONTROL TECHNIQUES DRIVE ................................ 40-11
DANFOSS DRIVE......................................................... 40-12
ELAU DRIVE................................................................. 40-13
EUROTHERM DRIVE ................................................... 40-14
EVER DRIVE ................................................................ 40-15
FANUC ROBOTICS DRIVE .......................................... 40-15
FAGOR DRIVE ............................................................. 40-16
GALIL DRIVE ................................................................ 40-17
GE DRIVE ..................................................................... 40-17
HITACHI DRIVE............................................................ 40-17
KEB DRIVE ................................................................... 40-18
INDRAMAT DRIVE ....................................................... 40-19
LENZE DRIVE .............................................................. 40-19
LUST DRIVE ................................................................. 40-20
OMRON DRIVE ............................................................ 40-21
OSAI DRIVE ................................................................. 40-21
PANASONIC DRIVE ..................................................... 40-21
PARKER AUTOMATION DRIVE .................................. 40-22
ROBOX DRIVE ............................................................. 40-23
S.B.C. DRIVE................................................................ 40-24
SEW-EURODRIVE DRIVE ........................................... 40-25
SIEI DRIVE ................................................................... 40-26
SIEMENS DRIVE .......................................................... 40-26
STBER DRIVE ........................................................... 40-27
TDE MACNO DRIVE..................................................... 40-27
TELEMECANIQUE DRIVE ........................................... 40-28
TRIO MOTION DRIVE .................................................. 40-28
DATALOGIC BARCODE READER............................... 40-29
ABB PLC ....................................................................... 40-30
AEG MODICON PLC .................................................... 40-33
ALLEN-BRADLEY PLC................................................. 40-34
ALTUS PLC .................................................................. 40-38
ATOS PLC .................................................................... 40-39
BECKHOFF PLC........................................................... 40-40
BOSCH PLC ................................................................. 40-42
B&R AUTOMATION PLC.............................................. 40-42
CROUZET RPX PLC .................................................... 40-42
FOXBORO PLC ............................................................ 40-43
FUJI PLC ...................................................................... 40-43
GE FANUC PLC............................................................ 40-44
GEFRAN PLC ............................................................... 40-45
HITACHI PLC................................................................ 40-46
IDEC IZUMI PLC........................................................... 40-48
KLCKNER MOELLER PLC ........................................ 40-49
KEYENCE PLC ............................................................. 40-50
KOYO PLC.................................................................... 40-50
KUHNKE PLC ............................................................... 40-52
LG PLC ......................................................................... 40-52
MATSUSHITA-NAIS PLC ............................................. 40-54
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CONTENTS
xviii
MICROLINK PLC .......................................................... 40-56

MITSUBISHI PLC.......................................................... 40-56
OMRON PLC ................................................................ 40-58
SAIA PLC ...................................................................... 40-60
SATT CONTROL PLC .................................................. 40-64
SCHLEICHER PLC ....................................................... 40-65
SIEMENS PLC .............................................................. 40-66
SPRECHER+SCHUH PLC ........................................... 40-69
SQUARE-D PLC ........................................................... 40-69
TELEMECANIQUE PLC ............................................... 40-70
TEXAS INSTRUMENTS PLC ....................................... 40-74
TOSHIBA PLC .............................................................. 40-76
HBM BALANCE SCALES ............................................. 40-77
ASCON THERMOREGULATOR .................................. 40-78
GEFRAN THERMOREGULATOR ................................ 40-78
HENGSTLER THERMOREGULATOR ......................... 40-79
WEST THERMOREGULATOR..................................... 40-80
Cable information summary .......................................... 40-81
Resistance to chemical Contents........................................................................ 41-1

substances Chemical substances .................................................... 41-2
Cleaning the VT ............................................................ 41-7
Case for terminals VT, H Series .......................................... 41-7
Technical support Contents........................................................................ 42-1

International Customer Care ......................................... 42-2
International Product Returns ....................................... 42-2
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

F-1
Foreword
The hardware installation manual is valid for all types of Video Terminal.
The manual The installation manual contains information on securing and connecting
both VTs and optional accessories, on the functions offered by the termi-
nals as well as on the cables connecting them to a device.
Its purpose The manual contains all the notions, concepts and examples necessary to be
able to install quickly and easily.
Conventions Below are listed the symbols and styles found in the manual together with
their respective meanings:
PLC Programmable logic control or other intelligent device

equipped with a serial connection.
Device Intelligent device or PLC equipped with a serial connec-

tion.
[] The contents of the bracket appears on the screen.
Identifies a key or touch button.
Indicates that the VT specified lacks this key.
Indicates an important point that requires attention.
There is a danger that the equipment will be damaged.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

I-1
Introduction
What is a A VIDEO TERMINAL (VT) is a device that allows the user to control or
Video simply monitor a productive process. It can send commands using con-
Terminal figured by the user; it can send data determining the process on hand and
can display information deriving from the productive process. The informa-
tion can be in the form of an Alarm, an Information (Info-) Message or in
binary data format.
The VTs can be divided into two groups: those with a keyboard and those
without but equipped with a Touch Screen.
All VTs can be supplemented with accessories to boost and broaden their
performance.
VTs are connected to the device by means of a serial connection.
For the VT to function a project must be created and loaded into it. See
Software Manual.
For detailed information on individual VTs see the relevant chapters below.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

E-1
Essential information
The VT is a device composed of a series of components which, given their

structure MUST be used in a particular way; in addition, these very struc-
tural characteristics may cause the VT to behave in ways that could be
interpreted as a malfunctioning of product and/or evidence of a construc-
tional defect.
The VT in such cases is NOT to be considered faulty and so nei-

ther repair nor substitution are appropriate.
The component that generally creates this impression is the display. The
displays used on the VTs are of two distinct types, one with a passive
matrix called STN (Super Twist Nematic) and the other with an active
matrix called TFT (Thin Film Transistor). Some of their working features
are the same, others depend on the different constructional technology.
One component that requires particular care when being used is the Touch
Screen.
Below we set out a series of points relating to possible behaviors and the
correct use of the VT.
Failure to put some of these notions into practice may damage the
VT.
Graphic The category graphic terminals covers both touch screen and keyboard ter-
terminals minals and includes both those with STN display and those with TFT dis-
play.
With CCFL backlit displays the brightness may be slightly uneven, the
areas where the CCFL lamps are may be lighter.
CCFL lamps
CCFL lamps
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

ESSENTIAL INFORMATION
E-2
All displays posses a certain viewing angle within which the images can
be seen properly. If the viewer is outside the specified angle the images
may be seen with their colors inverted or with different tones from the
original ones, or it may be that no colors are seen, etc. The viewing
angle can be slightly adjusted by regulating the contrast on the display.
9 oclock 3 oclock
g d
12 oclock
a
Viewer
b
6 oclock
The figure above shows the direction of the angles in relation to the
viewing point. The table gives the value of the viewing angles depend-
ing on the type of display.
Direction (Hour)
Type of display
12 - a 6-b 9-g 3-d
STN 30 degrees 60 degrees 60 degrees 60 degrees
TFT 80 degrees 80 degrees 70 degrees 70 degrees
This feature means a difference in viewing (albeit with the same contrast
and temperature levels) when:
The viewer is taller than the person setting the contrast.

Viewers find themselves at different distances from the VT.
Two identical displays may have slightly different brightness levels and
color tones.
E-3
Graphic Temperature influences the contrast of the display. At higher tempera-

terminals - tures the display is lighter while at lower temperatures it is darker, con-
STN sequently a few minutes are required after switching on before the
display offers normal viewing. This effect may be more or less marked
depending on the ambient temperature. For terminals with temperature
probes the contrast is automatically regulated so the effect is almost
imperceptible .
It is possible for images having a strong chromatic contrast with the

background to create color streaks. This effect can be slightly corrected
using the displays contrast control.
Streaking
Brightness may present a slight tremble or irregularity leading to a slight

darkening which extends over the entire display.
Graphic In some cases the display may have some pixels that are white (always
terminals - ON) or black (always OFF). This phenomenon may be visible or invisi-
TFT ble to the user on account of the color showing on the display. This phe-
nomenon is considered normal.
White pixels
Black pixels
Graphic The touch screen is activated by applying pressure equal to 200g which
terminals may be done using a pen or a finger.
Touch Screen
The touch screen also has a peripheral area that should never be sub-
jected to stress above all using pointed objects (pens, etc.). On account
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

ESSENTIAL INFORMATION
E-4
of how the glass is put together this area is very sensitive to pressure and
is fragile.
Useable area
Peripheral area
2mm
2mm
The peripheral area is about 2mm on each side and is outside the touch
sensitive area.
Subject this area to stress may damage the VT.

1-1
Chapter 1 General information on electromagnetic

compatibility (EMC)
Contents Page
Laying cables 1-2
Shielding of cables 1-2
Earthing of shielding and electronic circuits 1-2
Switching of capacitive loads 1-2
Switching off inductive loads 1-2
Disturbance suppression circuit - RC and DIODE 1-3

This chapter consists of 4 pages.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 1
1-2 General information on electromagnetic compatibility (EMC)
Electronic devices are being increasingly used in automated systems. pro-

grammable controllers (like the PLC) belong to this category, as do
Man-machine-interface systems (e.g. the Video Terminal), control systems
(e.g. diagnostic terminals), interface elements (e.g. interface boards) and
AC-DC drives. Together with this type of electronic apparatus, you find
installed classical electro-mechanical devices like contactors, elec-
tro-valves, motors etc.
Electrical disturbances caused by the operation of these devices can com-
promise the smooth functioning and the length of the working life of the
electronic devices present on the same switchboard or the same plant. To
get the best out of both the electrical and the electronic devices it is neces-
sary to reduce electrical disturbance.
Laying cables Remember to lay measurement, monitoring and communication cables so

that they are kept apart from power cables. Power cables laid close and par-
allel to communication cables can cause coupling voltages that are strong
enough to disturb or destroy electronic components.
Shielding of It is essential to use suitably shielded cables for communication signal con-
cables nections (total shielding is recommended). The shielding must be con-
nected to the zero potential.
Earthing of With many devices the "0V" is connected to the earth. The signal ground
shielding and must be earthed but it is best to separate the ground of the shields and cir-
electronic cuits from that of the power circuits. Note that the earth can only perform
circuits its function if the "Resistance of the earth circuit" is within the max. limits
prescribed.
Switching of The current peaks which occur when capacitive loads are switched on can
capacitive damage or destroy control devices. Furthermore, the high-frequency com-
loads ponent of the current peak can cause serious disturbance in electronic cir-
cuits as a result of inductive coupling between the connection cables.
Switching off When an inductive load is switched off, the magnetic energy stored tends to
inductive oppose this, discharging a voltage peak down the line which can damage or
loads destroy the control device. Furthermore, the high-frequency component of
the voltage peak can cause disturbance caused by capacitive coupling
between the connection cables.
The physical structure and characteristics of an inductive load make it
impossible to carry out switching without disturbance unless suitable mea-
sures are taken. The disturbance can be at least partially suppressed by fit-
ting a suitable disturbance-suppression module in parallel with the
inductive load. The disturbance-suppression module must not constitute an
additional load during the work phase. Electrical disturbance is propagated
both through the connection cables and electromagnetic transmission. If the
disturbance is propagated by cable or electromagnetic transmission, it is
much more difficult to suppress at the inputs to the units in the danger zone
than it is to suppress the disturbance at its source. If the disturbance is cre-
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

1-3
ated by connection cables or by electronic transmission, it is much more

difficult to suppress it at the inputs of the devices in dangerous areas than at
source,
If possible, disturbance should be suppressed at source.
Disturbance In the following tables there are the specifications of the disturbance sup-
suppression pression filter ciruits.
circuit - RC
and DIODE Table 1.1: Disturbance suppression circuit RC
Circuit Advantages Disadvantages
The residual component has a very low The best results are obtained by sizing
harmonic wave form component. the R/C suitably.
The residual overvoltage can be limited

Volume directly proportional to the
to the very low values by optimizing the
inductance and power of the load.
sizing.
C R
Optimal suppression is obtained as a
Switch-off time delay very low. direct consequence of a significant
de-energizing delay.
S
C
The presence of the capacitor causes a
The effectiveness of the disturbance
Ub L high load current peak when switching
R suppression is not affected by the volt-
on (and can cause pasting of the con-
age value. No switch-on delay.
tact if undersized).
Suitable for both AC and DC; no prob- The RC circuit constitutes an additional
lem with reversed polarity. load when used with AC.
No arc (low energy) on switching con-

--
tact.
Table 1.2: Disturbance suppression circuit DIODE
Circuit Advantages Disadvantages
Very compact. High switch-off delay time.
D No residual voltage (total damping of For direct current (DC) applications

disturbance impulse). only.
S Easy to size. Polarity must be respected.
Ub L D
Switch-off delay can lead to the forma-

--
tion of a strong electric arc.
Sensitive to disturbance voltage pulses

--
in power supply circuit.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

2-1
Chapter 2 Power Supply
Contents Page
Connection pins 2-2
Wiring 2-2
Connections to be avoided 2-2
Recommended connection 2-3

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 2
2-2 Power Supply
Use a 24VDC (18..32Vdc) power supply unit to power the VT.
Connection
pins Table 2.1: 4 pin Power Supply Connector
Connector Pin Meaning
1 Input power +24Vdc

4 3 2 1
2 Input power 0Vdc
3 Not connected
- +
N.C. 24VDC
4 Earth protection
Check all connections before switching on.
Wiring The power supply connector will take conductors with a cross-section of
between 0.05 and 2.5mm (30-12AWG) for rigid conductors or from 0.05
to 1.5mm (30-12AWG) in the case of flexible conductors. The length of
the stripped wire must be between 6 and 7.5mm (0.24-0.30in). The recom-
mended screw grip pressure is 0.79Nm (7 lb in).
These values represent the maximum values certificated. The

screw grip pressure is related to the norms applicable to the prod-
uct and to the type of use.
Connections The connections illustrated below must not be made as they may cause the
to be avoided VT to be damaged.
Table 2.2: Connections to be avoided
L1 L1
N N
PE PE
~ ~
- + - +
24V 24V
The above configurations will seriously damage certain compo-

nents of the VT.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

2-3
Beware of appliances with the POSITIVE connected to PE.
It is vital that the earth of the devices connected to the serial

and/or parallel communication ports have the same voltage as the
0V supply of the VT. The circulation of current between the 0V supply
and the earth of the communication ports could damage certain com-
ponents of the VT or of the devices connected it.
Recommended We recommend a wiring scheme as set out below in the interests of avoid-
connection ing damaging the VT.
Table 2.3: Power supply with 0Vdc connected to PE
L1
N
PE
- + PLC
24V
PE
+24V
0V
VT
1
2
3
4
Correct earthing is essential.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

3-1
Chapter 3 Video terminal VT50
Contents Page
Technical characteristics 3-4
Functions 3-8
Front face 3-8
Standard series rear view 3-9
CAN series rear view 3-10
Dimensions and Cut-out 3-11
Accessories 3-12
Termination of CAN line 3-12
Transfer PC -> VT 3-12
Preparation for reception 3-13
Information relating to driver 3-14
Adjusting the contrast on the display 3-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 3
3-2 Video terminal VT50
Help
VT50
F1 F2 F3 F4 F5 Info
Shift
Esc
Technical The following table lists the principal technical characteristics of the prod-
characteristics uct in question.
Code of terminal Characteristics of the terminal

VT050 00000
VT050 000CN
Display
Type LCD
Representational format Text
Rows by characters 2 x 20
Display area size [mm] 73,5 x 11,5
Character matrix in text mode [pixels] 5x7
Character size [mm] 3,2 x 5,5
Trimmer
Contrast adjustment
Automatic compensation with temperature
Character sets Ascii, Katakana
Backlighting
LED
Type
CCFL lamp
Minimum lamp-life at 25C [hours] --
Keyboard
Non-customizable function keys 5
Customizable function keys --
Function key LEDs --
Alphanumeric keys --
Operational keys 8
Operational key LEDs --
Diagnostic LEDs --
User memory
Project [Bytes] 256K
Data memory [Bytes] --
Memory for Windows -based fonts [Byte] --
Memory Card for backup --
Memory Card for expansion --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

3-3

VT050 00000
VT050 000CN
Interfaces
MSP (Multi-serial port) RS232/RS422/RS485/TTY-20mA
ASP (Auxiliary serial port) RS232/RS485
ASP-15L (Auxiliary serial port) RS232/RS485
ASP-8 (Auxiliary serial port) RS232
LPT parallel port Centronics
Auxiliary port Connection for accessory devices
Accessories
Connectable accessories See table Chapter 33
Clock
Clock
Networks
Profibus-DP
Integrated CAN Open (Optoisolated interface)
Ethernet 10/100Mbit RJ45
Universal Bus Connector --
Optional See table Chapter 33
Proprietary networks
Network server
ESA-Net
Network client
Technical data
Power supply 24Vdc (18..32Vdc)
Power absorbed at 24Vdc 5W
Protection fuse 5x20mm - 315mA Quick Blow F
Protection level IP65 (front-end)
Operating temperature 0..50C
Storage and transportation temperature -20..+60C
Humidity (non-condensing) <85%
Weight 500gr
Dimensions
External W x H x D [mm] 166 x 86 x 41
Cut-out W x H [mm] 157 x 77
Certification
Certifications and approvals CE, RINA, DNV, cULus, NEMA12
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 3
Functions The following table lists in alphabetical order all the functions of the VT in
question.
Table 3.1: Functions and objects realizable with this VT (Part 1 of 4)

Code of terminal
VT050
Objects/Functions Quantity
Alarm field
Alarm help
Alarm history buffer
Alarm statistics
Alarms (Total/active simultaneously)
Arc
Automatic operations 20
Backup/Restore
Bar data
Bit-wise password 8bits
Buttons
Circles
Command: Change language
Command: Clear trend buffer

Command: Delete recipe
Command: Hardcopy
Command: Load recipe from data memory
Command: Modify password
Command: Next page
Command: Page help
Command: Password login
Command: Password logout
Command: Previous page
Command: Print alarm history
Command: Printer form feed
Command: Quit project
Command: Report
Command: Restarts reading time-sampled trend
Command: Run pipeline
Command: Save alarms history and trend buffers in flash
Command: Save recipe in data memory
Command: Save recipe received from device in buffer
Command: Save recipe received from device in data memory
Command: Send recipe from video buffer to device
Command: Send recipe to device
Command: Service page
Unless otherwise stated, there is no limit to the number of includable elements, only the size of project memory sets a limit.
*) indicative value determined by the dimensions of the project
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

3-5

Code of terminal
VT050
Command: Show alarms history
Command: Show page directory
Command: Show project information
Command: Show recipe directory

Command: Show sequence directory
Command: Shows driver status page

Command: Shows page help
Command: Shows page with function: PG
Command: Stops reading time sampled trend
Command: Trend reading saved in device
Command: Zero number of general pages
Date field
Day-of-the-week field
Dynamic texts: Bit-group-structured dynamic texts
Dynamic texts: Single-bit dynamic texts 1024*
Dynamic texts: Value-structured dynamic texts
E-keys
Equations 32
F-keys
Free terminal
Function: Disables key
Function: Go to page
Function: Internal command
Function: Invert bit value
Function: Macro
Function: None
Function: Reset bit permanently

Function: Reset real-time bit
Function: Sequences
Function: Sets bit permanently

Function: Sets real-time bit
Function: Value-structure direct command
Global configuration of E-keys

Global configuration of F-keys
Headers and footers (Total/Number of fields per H-F)

Info-messages (Total/active simultaneously) 128/128
Internal registers 512bytes
Labels
LEDs assigned to sequence

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 3

Code of terminal
VT050
Lines
Lists of bitmap images
Lists of texts
Local configuration of E-keys

Local configuration of F-keys
Macro field 4 x pages

Macros (Total/Commands x macro)
Message field
Message help 128
Multilanguage texts 4 Langs.
Object - Indicator
Object - Potentiometer knob
Object - Selector knob
Object - Sliding potentiometer
Object - Sliding selector
Page 127
Page help 127
Password
Pipelines (Number/Tot bytes)
Print
Print page (Total/Number of fields per page)
Programmable fonts
Project images
Public variables of ESANET network (Number/Total bytes)
Recipe field for recipe structure
Recipes (Number of variables per recipe)
Rectangles
Redefinable characters 7
Reports
Sequences - Random
64
Sequences - Start/stop
Static bitmaps
Symbolic field: Bit-group-structured dynamic bitmaps
Symbolic field: Single-bit-structured dynamic bitmaps
Symbolic field: Value-structured dynamic bitmaps
System messages
System variables assigned to recipe structure
Time long field
Time short field
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

3-7

Code of terminal
VT050
Timer 20
Touch Area
Trend buffers
Trends (Trends x page/Channels x trend)
Trends sampled automatically (Memory/Trends/Readings)
Trends sampled on command (Memory/Trends/Readings)
Value direct command: ADD
Value direct command: AND
Value direct command: OR
Value direct command: SET
Value direct command: SUBTRACT

Value direct command: XOR
Variables: Limit values and linear scaling variables
Variables: Movement variable (Mobile symbolic field)
Variables: Threshold variables
12 x pages
Variables: Floating Point numerical variables
Variables: Numerical variables (DEC, HEX, BIN, BCD)
Variables: String variables (ASCII)

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 3
Front face
1
Help
VT50
F1 F2 F3 F4 F5 Info
Shift
Esc
Key Function
1 Display
Shift + 2 F-keys
F5
Confirms setting
Help
Next page
Info
Previous page
F4
Start in-putting
F3
Moving cursor between fields
F2
Moving cursor between fields
F1 Quits: setting of data, info-messages, directory of sequences,

Esc communication driver
Info
Shift + Displays information messages
Help
Shift + Displays according to context: info-message help or page help
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

3-9
Standard
series rear
view
A
C
Position Function
A Power supply connector
B MSP serial port
C Trimmer for adjusting display contrast
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 3
CAN series
rear view
C
A
D B
Position Function
B ASP-8 serial port
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

3-11
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 3
To fix the sealing gasket and secure the VT to the container see Chapter 29
-> Mounting the terminal within the container.
Where accessories need to be fixed in or onto the VT terminal, you

are advised to do this before securing the VT to its container.
Accessories Any accessories should be mounted in accordance with the instructions in

the relevant chapter (see Chapter 33 -> Video terminal accessories).
Termination of This paragraph applies only to the CAN series. The VT in question inte-
CAN line grates the termination resistances of the serial line (typically 120 ohms)
which can be inserted by means of a jumper (preset on 1-2, line not termi-
nated). To activate the termination:
Make sure the device is not connected to the power supply.

Remove the cover.
Identify the jumper unit J2.
T
3
2
1
J2
Position the jumper between pins 2 and 3 (line terminated).

Replace the back cover.
Reconnect the power supply.
Transfer PC -> For everything to function properly, the first time the VT operator terminal
VT is switched on it needs to be correctly loaded, that is it needs to have trans-
ferred to it:
Firmware
Communication driver
Project
(Given that the transfer of the three files in practice occurs with a single
operation, it will be defined as Project transfer for the sake of simplicity)
or:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

3-13
Free terminal protocol
For this it is essential that the VT be prepared to receive the transfer. (See
also Chapter 37 -> Command area).
Preparation for The program VTWIN (see Software Manual) must be used for the transfer,
reception but the terminal must be set up to receive. This means carrying out the fol-
lowing steps:
Check that the VT is off

Check that there is a serial connection between the PC and the VT
F5
Switch on the VT with held down and wait a moment
VT terminal with no Modem function:
The following mask appears. The VT is now ready to receive (refer to

Software Manual for transfer procedure)
VT50 Service page
VT terminal with Modem function:
The following mask appears
F1=MODEM - F2= PC
Choose the required transfer mode: MODEM if you intend to use a

modem or PC if you intend to use a serial port; press the corresponding
function
If the choose made is PC, the VT is ready to receive (see Software Manual
for transfer), if, on the other hand, you choose MODEM, the following
mask will appear
F1=FAST - F2=SLOW
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 3
The choice should be according to the speed you intend to use for the transfer
(Slow=9600bit/sec or Fast=38400bit/sec), press the corresponding function
. The VT is now ready to receive (see Software Manual for the transfer).
Information After the project has been transferred, the VT can make available informa-
relating to tion relating to what has been loaded. The information regards:
driver
The name of the driver loaded
The version of the driver loaded
Network address of the VT
Last error to have occurred
To acquire this information carry out the following operations:
Be situated in any page of the project

Shift
Press twice; you will see
Driver: xxxxxxxxxxxxx Help

o Info Addr. : xxxxxxxxxxxxx
Ver. : xxxxxxxxxxxxx Error : xxxxxxxxxxxxx
The possible error messages are:
PROT ERROR
Problem-> Errors have been detected in the data exchange between

the VT and the Device.
Solution-> Check the cable; there may be disturbance.
COM BROK
Problem-> Communication between VT and Device interrupted.

Solution-> Check the serial connection cable.
An error message followed by [*] indicates that the error is not currently
present but was and has since disappeared.
Example: COM BROK*
Adjusting the To improve the quality of the representation on the display it may be neces-
contrast on sary to adjust its contrast. This can be done by rotating the trimmer (C) at
the display the back of the VT (see Page 3-9 or Page 3-10); turn it (using a small screw-
driver or a trimmer tool) in one direction and, if the display quality wors-
ens, turn it the other way.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

4-1
Chapter 4 Video terminal VT60
Contents Page
Functions 4-4
Front view 4-8
Accessories 4-12

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 4
Help F1
Esc
F2
F3
VT60
F4
Shift
Enter

VT060 00000
VT060 000CN
Display
Type LCD
Trimmer
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
Keyboard
Customizable function keys --
Function key LEDs --
Operational keys 6
Diagnostic LEDs --
User memory
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

4-3

VT060 00000
VT060 000CN
Interfaces
Accessories
Clock
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 500gr
Dimensions
Certification
Certifications and approvals CE, RINA, DNV, cULus, NEMA12
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 4
question.

Code of terminal
VT060
Alarm field
Alarm help
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons
Circles

Command: Hardcopy
Command: Next page
Command: Page help
Command: Report
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

4-5

Code of terminal
VT060


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None

Function: Sequences



Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 4

Code of terminal
VT060
Lines
Lists of texts


Macros (Total/Commands x macro)
Message field
Message help 128
Object - Indicator
Page 127
Page help 127
Password
Print
Programmable fonts
Project images
Rectangles
Reports
Sequences - Random
64
Static bitmaps
System messages
Time long field
Time short field
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

4-7

Code of terminal
VT060
Timer 20
Touch Area
Trend buffers

12 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 4
Front view
Help F1
Esc
F2
1 F3
2
VT60
F4
Shift
Enter
Key Function
1 Display
Shift + 2 F-keys
F4
Opens and confirms setting
Enter
F1
Page up
F2
Page down
F3
Move cursor between fields
Help Quits: setting of data, information messages, sequence direc-

Esc tory, communication driver
Help
Displays information messages
Esc
Help
Shift + Displays according to context: info-message help or page help
Esc
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

4-9
Standard
series rear
view
A
C
Position Function
B MSP serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 4
CAN series
rear view
C
A
D B
Position Function
B ASP-8 serial port
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

4-11
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 4



Remove the cover.
T
3
2
1
J2

ferred to it:
Firmware
Project
operation, it will be defined as Project transfer for the sake of simplicity.)
or:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

4-13
Free terminal protocol
lowing steps:

F4
Switch on the VT with Enter
pressed down and wait a moment

VT60 Service page
F1=MODEM - F2= PC

function
mask will appear
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 4
F1=FAST - F2=SLOW
The choice should be according to the speed you intend to use for the trans-
fer (Slow=9600bit/sec or Fast=38400bit/sec), press the corresponding func-
tion . The VT is now ready to receive (see Software Manual for the
transfer).
driver

Shift
Press twice; you now see
Driver: xxxxxxxxxxxxx
Ver. : xxxxxxxxxxxxx
Addr. : xxxxxxxxxxxxx
Error : xxxxxxxxxxxxx
The possible error messages are:
PROT ERROR

COM BROK

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

4-15
Example: COM BROK*
the display the back of the VT (see Page 4-9 or Page 4-10); turn it (using a small screw-
driver or a trimmer tool) in one direction and, if the display quality wors-
ens, turn it the other way.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

5-1
Chapter 5 Video terminal VT150W
Contents Page
Functions 5-4
Front view 5-8
Customizing label 5-10
Accessories 5-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 5
5-2 Video terminal VT150W
VT150W
F6 F7 F8 F9 F10
F1 F2 F3 F4 F5
V Y +
PgUp
W Z / Info
X 7 - 8 = 9
M P S
PgDn
N Q T Help
O 4 R 5 U 6
D G J
E H K
F 1 I 2 L 3
A . Clr
shift B
C 0 Space
Esc
Enter

VT150W 00000
VT150W 000DP
VT150W A00CN
Display
Type LCD
Trimmer
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
Keyboard
Non-customizable function keys --
Customizable function keys 5
Function key LEDs 5
Alphanumeric keys 11
Operational keys 9
Operational key LEDs 2
Diagnostic LEDs
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

5-3

VT150W 00000
VT150W 000DP
VT150W A00CN
User memory
Interfaces
Accessories
Clock
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 700gr
Dimensions
Certification
Certifications and approvals CE, cULus, NEMA12
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 5
question.

Code of terminal
VT150W
Alarm field
Alarm help
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons
Circles

Command: Hardcopy
Command: Next page

Command: Page help

Command: Report
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

5-5

Code of terminal
VT150W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 5

Code of terminal
VT150W
Lines
Lists of texts

Macros (Total/Commands x macro) 1024/16
Message field
Message help 1024
Object - Indicator
Page 1024
Page help 1024
Password 10

Print
Programmable fonts
Project images
Public variables of ESANET network (Number/Total bytes) 128/1024

Rectangles
Reports
Sequences - Random
64
Static bitmaps
System messages

Time long field
Time short field
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

5-7

Code of terminal
VT150W
Timer 32
Touch Area
Trend buffers

32 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 5
Front view
VT150W
2
F6 F7 F8 F9 F10
F1 F2 F3 F4 F5
3 V
W
Y
Z
+
/ Info
PgUp
X 7 - 8 = 9
M P S
PgDn
N Q T Help
4 5 6
4
O R U
D G J
E H K
F 1 I 2 L 3
A . Clr
shift B
C 0 Space
Esc
Enter
Key Function
1 Display
2 F-key customizing label
3 F-keys
4 Alphanumeric and operative keys
Opens and confirms input

Enter
PgUp Page up
When in setting phase, edits dynamic text
PgDn Page down

When in setting phase, edits dynamic
Moves the cursor between settable fields

When in setting phase, moves cursor to the left of the field

When in setting phase, moves cursor to the right of the field
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

5-9
Key Function
Clr
Quits: setting of data, info-messages, sequence directory, com-
Esc
munication driver
Info Displays info-messages
Displays according to context: information message help or page

Help
help
Clr
Shift + Esc
In setting phase restores the initial value of the field
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 5
Customizing
label
Position Function - Dimensions L x H (mm)
1 ESA Logo - 65 x 12
2 VT Model - 65 x 12
3 F-key customization F - 116 x 16
The total thickness of the label must not exceed 125m (microme-
ters). Do not use either stiff materials or glues.
Before starting to insert the customized label, see Chapter 28 ->

Inserting customized labels.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

5-11
Standard
series rear
view
C
Position Function
B Auxiliary port for connecting optional accessories
C Trimmer for adjusting contrast of the display
D MSP serial port
E NETWORK serial port for network communication (Option)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 5
CAN series
rear view
Position Function
B Auxiliary port for connecting optional accessories
C Trimmer for adjusting contrast of the display
D ASP-8 serial port
E CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

5-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 5



Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

5-15

ferred to it:
Firmware
Project
lowing steps:

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 5
Switch on the VT with Enter pressed down or with the VT on press

shift
together + Enter
; in either case wait a moment

Boot forced
F1=MODEM - F2= PC

function
mask will appear
F1=FAST - F2=SLOW
transfer).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

5-17
driver

Shift
VT150W
Serial: xxxxxxxxxxxxx
PgDn PgUp
Press or to display
Up/Down: next page
Possible error messages are:
PROT ERROR

COM BROKEN

Example: COM BROKEN*
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 5
the display the back of the VT (see Page 5-11 or Page 5-12); turn it (using a small
screwdriver or a trimmer tool) in one direction and, if the display quality
worsens, turn it the other way.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

6-1
Contents Page
Functions 6-4
Front view 6-8
Rear view 6-11
Accessories 6-13

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 6
VT160W
F6 F7 F8 F9 F10
F1 F2 F3 F4 F5
V Y +
PgUp
W Z / Info
X 7 - 8 = 9
M P S
PgDn
N Q T Help
O 4 R 5 U 6
D G J
E H K
F 1 I 2 L 3
A . Clr
shift B
C 0 Space
Esc
Enter

VT160W 00000
VT160W 000DP
Display
Type LCD
Trimmer
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
Keyboard
Function key LEDs 23
Operational keys 9
Diagnostic LEDs --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

6-3

VT160W 00000
VT160W 000DP
User memory
Interfaces
Accessories
Clock
Clock
Networks
Profibus-DP
Proprietary
Network server
ESA-Net
Network client
Technical data
Weight 880gr
Dimensions
Cut-out W x H [mm] See diagram
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 6
question.

Code of terminal
VT160W
Alarm field
Alarm help
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons
Circles

Command: Hardcopy
Command: Next page

Command: Page help

Command: Report
*) indicative value determined by the dimensions of the project, **) not present with VT160I/O driver
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

6-5

Code of terminal
VT160W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences
Global configuration of E-keys **

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 6

Code of terminal
VT160W
Lines
Lists of texts
Local configuration of E-keys **
Macro field
Message field
Message help 1024
Object - Indicator
Page 1024
Page help 1024
Password 10

Print
Programmable fonts
Project images

Rectangles
Reports
Sequences - Random
64
Static bitmaps
System messages

Time long field
Time short field
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

6-7

Code of terminal
VT160W
Timer 32
Touch Area
Trend buffers

32 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 6
Front view
5 6
VT160W
1
7
2 8
F6 F7 F8 F9 F10
F1 F2 F3 F4 F5
3 V
W
Y
Z
+
/ Info
PgUp
X 7 - 8 = 9
9
M P S
PgDn
N Q T Help
4 5 6
4
O R U
D G J
E H K
F 1 I 2 L 3
A . Clr
shift B
C 0 Space
Esc
Enter
Key Function
1 Display
2 F-key customizing label
3 F-keys
5 22mm diameter pre-cut for mounting emergency stop button
6 Customizing label for command and/or signal elements
16mm diameter pre-cuts for mounting command and/or signal

7
elements
8 E-key customizing label
9 E-keys
Opens and confirms input

Enter
PgUp Page up
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

6-9
Key Function
PgDn Page down



Clr
Esc
munication driver
Displays according to context: information message help or page

Help
help
Clr
Shift + Esc
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 6
Customizing
label
1
3
1 ESA Logo, VT Model - 101 x 13
3 Customizing label for command and/or signal elements - 112 x 8
4 F-key customization E - 149 x 16

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

6-11
Rear view
A B
C D
Position Function
B Trimmer for adjusting contrast of the display
C MSP serial port
D NETWORK serial port for network communication (Optional)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 6
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

6-13


VT is switched on it needs to be correctly loaded, that is, it needs to have trans-
ferred to it:
Firmware
Project
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 6
lowing steps:

Switch on the VT with Enter pressed down or with the VT on press
shift
together + Enter
; in either case wait a moment

Boot forced
F1=MODEM - F2= PC

function
mask will appear
F1=FAST - F2=SLOW
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

6-15
transfer).
driver

Shift
VT160W
PgDn PgUp
Press or to display
Up/Down: next page
PR ERROR

COM BROKEN

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 6
the display the back of the VT (see Page 6-11); turn it (using a small screwdriver or a
trimmer tool) in one direction and, if the display quality worsens, turn it the
other way.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

7-1
Contents Page
Functions 7-4
Front view 7-8
Rear view 7-11
Accessories 7-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 7
VT170W
X0 Power Battery
F1 F2 F3 F4 F5 F6
F7 F8 F9 F10 F11 F12

V Y +
W Z / Info Alarm Help
X 7 - 8 = 9
M P S Ack PgUp Clr
N Q T All
O 4 R 5 U 6 Ack Esc
D G J
E H K
F 1 I 2 L 3
A . PgDn
shift B Enter
C 0 Space

VT170W A0000
Display
Type LCD
Trimmer
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
Keyboard
Operational keys 13
Diagnostic LEDs 3
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

7-3

VT170W A0000
User memory
Data memory [Bytes] 32K (With back-up battery)
Interfaces
Accessories
Clock
Clock Hardware (With back-up battery)
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 900gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 7
question.

Code of terminal
VT170W
Alarm field
Alarm help 1024
Alarm history buffer 256
Alarm statistics
Alarms (Total/active simultaneously) 1024/128
Arc
Automatic operations
Backup/Restore
Bar data
Buttons
Circles

Command: Hardcopy
Command: Next page

Command: Page help

Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

7-5

Code of terminal
VT170W

Date field
E-keys
Equations
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Headers and footers (Total/Number of fields per H-F) 128/128
Internal registers
Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 7

Code of terminal
VT170W
Lines
Lists of texts

Macro field
Message field
Message help 1024
Object - Indicator
Page 1024
Page help 1024
Password 10

Print
Print page (Total/Number of fields per page) 1024/64
Programmable fonts
Project images
Recipes (Number of variables per recipe) 1024/256
Rectangles
Reports 128
Sequences - Random
128
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

7-7

Code of terminal
VT170W
Timer
Touch Area
Trend buffers

16 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 7
Front view
VT170W
4
1
5
X0 Power Battery
F1 F2 F3 F4 F5 F6 6
2
F7 F8 F9 F10 F11 F12
V Y +
W Z / Info Alarm Help
X 7 - 8 = 9
M P S Ack PgUp Clr
N Q T All
4 5 6
3
O R U Ack Esc
D G J
E H K
F 1 I 2 L 3
A . PgDn
shift B Enter
C 0 Space
Key Function
1 Display
2 F-keys
4 X0 LED. Blinks when communication error is detected
5 Power LED. Lights up when power in ON
6 Battery LED. Lights up when the battery has nearly run out
Start input
Enter Confirms setting of data
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

7-9
Key Function
PgUp Page up
PgDn Page down



Clr
Esc
munication driver
Alarm Displays ISA alarms
Displays according to context: information message help, alarm

Help
help or page help
Ack
All
Ack
Acknowledgment of ISA alarms on display
Print the entire display area
Clr
shift + Esc
Ack
shift + All
Ack
Acknowledges all ISA alarms
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 7
Customizing
label
1 2

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

7-11
Rear view
C H
D G
E F
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 7
Position Function
A Trimmer for adjusting display contrast
B Battery compartment
C NETWORK1 serial port for network communication (Optional)
D ASP-9 serial port for communicating with PC or other devices
E Power supply connector
F Fuse holder
G MSP serial port for communicating with PLC/PC
H NETWORK2 serial port for network communication (Optional)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

7-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 7


ferred to it:
Firmware
Project
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

7-15
Preparation The program VTWIN (see Software Manual) must be used for the transfer,
for reception but the terminal must be set up to receive. This means carrying out the fol-
lowing steps:

Enter
Switch on the VT with pressed down or with the VT on press
shift Enter
together + ; in either case wait a moment
The following mask appears.Press the function corresponding to the

port to be used. The VT is now ready to receive (refer to Software Man-
ual for transfer procedure)
Boot sequence forced

F1=ASP down/up load
F2=MSPdown/up load
ENTER=run project
Proceed from the preceding mask; the following mask appears

F1=MODEM dn/up load
F2=PC dn/up load
ENTER= run project
Choose the required transfer mode: MODEM if you intend to use a modem
or PC if you intend to use a serial port; press the corresponding function
mask will appear

F1=SLOW dn/up load
F2=FAST dn/up load
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 7
transfer).
driver

Shift
VT170W
PgDn PgUp
Press or ; you will see
Up/Down = next page
Enter = set clock
Enter
While displaying this page, press to access the clock setting page
For the clock to be used properly, a special battery has to be

inserted in the terminal (see Chapter 33 -> Video terminal accesso-
ries).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

7-17
Time Date
hh:mm:ss dd/mm/yy
Lf/Rt/Up/Dw = change
Esc=Prj Enter=Memo
PgUp
Lf is the equivalent of , Rt is the equivalent of , Up of , Dw of

PgDn Clr
Enter
Esc
; using you quit the display, while with the settings are con-
firmed and you return to the project page.
Possible error messages that can be displayed on the appropriate line are:
PR ERR

COM BROKEN


Clr
Esc
By pressing you pass back to the project page.
the display the back of the VT (see Page 7-11); turn it (using a small screwdriver or a
trimmer tool) in one direction and, if the display quality worsens, turn it the
other way.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

8-1
Contents Page
Functions 8-4
Front view 8-8
Rear view 8-11
Accessories 8-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 8
VT190W
X0 Power Battery
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11
F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22
. V Y +
F23 F24 PgUp Clr
W Z / Spare
Space X 7 - 8 = 9 Esc
M P S
Alarm Info shift N Q T
O 4 R 5 U 6
A D G J
Ack PgDn
Help B E H K Enter
All Ack
C 0 F 1 I 2 L 3

VT190W A0000
VT190W AP000
Display
Type LCD
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
Keyboard
Operational keys 14
Diagnostic LEDs 3
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

8-3

VT190W A0000
VT190W AP000
User memory
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1500gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 8
question.

Code of terminal
VT190W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Automatic operations
Backup/Restore
Bar data
Buttons
Circles

Command: Hardcopy
Command: Next page

Command: Page help

Command: Report



405.1200.037.2 - Rel.: 2.20 of 26/03/2007

8-5

Code of terminal
VT190W

Date field
E-keys
Equations
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Internal registers
Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 8

Code of terminal
VT190W
Lines
Lists of texts

Macro field
Message field
Message help 1024
Object - Indicator
Page 1024
Page help 1024
Password 10
Pipelines (Number/Tot bytes) 64/512
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
128
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

8-7

Code of terminal
VT190W
Timer
Touch Area
Trend buffers

32 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 8
Front view
4
1
5
VT190W
X0 Power Battery
6
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11
2
F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22
.
3
V Y +
F23 F24 Clr
PgUp
W Z / Spare
M P S
O 4 R 5 U 6
A D G J
Ack PgDn
Help B E H K Enter
All Ack
C 0 F 1 I 2 L 3
Key Function
1 Display
2 F-keys with two LEDs
3 F-keys with one LED
7 Alphanumeric keys
Starts input
PgUp Page up
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

8-9
Key Function
PgDn Page down



Clr
Esc
munication driver

Help
help or page help
Ack
All
Ack
Spare No predefined function
Clr
shift + Esc
Ack
shift + All
Ack
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 8
Customizing
label
1 3
2 4
2 F-key customization F1... F5, F12... F16 - 116 x 15

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

8-11
Rear view
H G
B C D E F
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 8
Position Function
A Battery compartment
B Power supply connector
C Fuse holder
D MSP serial port for communicating with PLC/PC
E ASP-9 serial port for communicating with PC or other devices
F LPT port for connecting printer (Optional)
G NETWORK2 serial port for network communication (Optional)
H NETWORK1 serial port for network communication (Optional)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

8-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 8


ferred to it:
Firmware
Project
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

8-15
lowing steps:

Enter
shift Enter
The following mask appears.Press the function corresponding to the

port to be used. The VT is now ready to receive (refer to Software Man-
ual for transfer procedure)

F1= ASP down/up load
F2= MSP down/up load
ENTER=run project

F1= MODEM dn/up load
F2= PC dn/up load
ENTER=run project

function
mask will appear
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 8

F1= SLOW dn/up load
F2= FAST dn/up load
transfer).
driver

Shift
VT190W
PgDn PgUp
Press or ; you will see
Up/Down = next page
Enter = settings page
Enter
If while displaying this page you press you will access the page for set-
ting the clock and the contrast
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

8-17

ries).
CONTRAST:####
TIME: hh:mm:ss DATE: dd:mm:yy
Left/Right = select. Up/Down = change
ESC = project ENTER = memo
PgUp PgDn Clr

Esc
Left/Right is equivalent to , Up/Down to ; using you
Enter
quit display, while with the settings are confirmed and you pass back
to the project page.
PR ERR

COM BROKEN

Clr
Esc
By pressing you pass back to the project page.
contrast on sary to adjust its contrast. This can be done by going to the page proposed
the display (see Page 8-11) and changing the value (from +31 to -32) in evidence at
that moment. Increase the value to darken the display; to lighten it decrease
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-1
Contents Page
Functions 9-4
Front view 9-8
Accessories 9-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9
VT300W
X0 Power Battery
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11
F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22
. V Y +
F23 F24 Clr
PgUp
W Z / Spare
M P S
O 4 R 5 U 6
A D G J
Ack PgDn
Help B E H K Enter
All Ack
C 0 F 1 I 2 L 3

VT300W A0000
VT300W AP000
VT300W 000CN
Display
LCD monochromatic STN
Type LCD 16 Colors STN
LCD 16 Colors TFT
Representational format Graphic
Resolution [pixels] 240 x 64
Rows by characters 8 x 40 / 4 x 20 / 2 x 10
Display area size [mm] 132 x 39
Character matrix in text mode [pixels] 6 x 8 / 12 x 16 / 24 x 32
Character size [mm] x 1 / x 2 / x 4 3,2 x 4,2 / 6,5 x 8,5 / 12,7 x 17
Software
Contrast adjustment
Character sets Programmable fonts/TTF Windows
Backlighting
LED
Type
CCFL lamp
Keyboard
Operational keys 14
Diagnostic LEDs 3
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-3

VT300W A0000
VT300W AP000
VT300W 000CN
User memory
Project [Bytes] 192K + 384K (Text+ Graphics)
Memory for Windows -based fonts [Byte] 64K
Memory Card for backup 4Mb
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1500gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9
question.

Code of terminal
VT300W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons
Circles
Command: Hardcopy
Command: Next page

Command: Page help

Command: Report


*) indicative value determined by the dimensions of the project, **) depends on memory available
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-5

Code of terminal
VT300W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences
Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9

Code of terminal
VT300W
Lines
Lists of texts

Message field
Message help 1024
Object - Indicator
Page 1024
Page help 1024
Password 10
Pipelines (Numero/Tot bytes) 64/512
Print
Programmable fonts
Project images
Public variables of ESANET network (Number/Tolat bytes) 256/1024
Rectangles
Redefinable characters
Reports 128
Sequences - Random
128
Static bitmaps
Symbolic field: Single-bit-structured dynamic bitmaps 1024*
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-7

Code of terminal
VT300W
Timer 16
Touch Area
Trend buffers 128
Trends (Trends x page/Channels x trend) 2/2
Trends sampled automatically (Memory/Trends/Readings) 512bytes
Trends sampled on command (Memory/Trends/Readings) /**/240

80 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9
Front view
4
1
5
VT300W
X0 Power Battery
6
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11
2
F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22
.
3
V Y +
F23 F24 PgUp Clr
W Z / Spare
M P S
O 4 R 5 U 6
A D G J
Ack PgDn
Help B E H K Enter
All Ack
C 0 F 1 I 2 L 3
Key Function
1 Display
7 Alphanumeric keys
Starts input
PgUp Page up
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-9
Key Function
PgDn Page down



Clr
Esc
munication driver

Help
help or page help
Ack
All
Ack
Clr
shift + Esc
Ack
shift + All
Ack
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9
Customizing
label
1 3
2 4

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-11
Standard
series rear
view A
B C D E
Position Function
A Auxiliary port for connecting optional accessories
C LPT port for connecting printer (Optional)
D ASP serial port for communicating with PC or other devices
E MSP serial port for communicating with PLC/PC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9
CAN series
rear view
A
B C D E
Position Function
C LPT port for connecting printer (Optional)
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9



Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-15

ferred to it:
Firmware
Project
lowing steps:

Enter
shift Enter
The following mask appears. F3=MemoCARD is only enabled when a
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9
Memory Card has been inserted in the VT terminal (see Page 9-18). The
function to press depends on which port you intend to use (MSP or
ASP). The VT is now ready to receive (refer to Software Manual for
transfer procedure)
VT300 TRANSFER PAGE
Graphic controller BOOT check : OK

Graphic controller RAM check : OK
F1=ASP F2=MSP F3=MemoCARD ENTER=Prj
VT300 TRANSFER PAGE

F1=MODEM F2=PC ENTER=Prj

function
mask will appear
VT300 TRANSFER PAGE

F1=SLOW F2=FAST
(Slow=9600bit/sec or Fast=38400bit/sec), press the corresponding function
. The VT is now ready to receive (see Software Manual for the transfer).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-17
driver
Serial ports present

Shift
Port : xxxxxxxxxxxxxxxxxxxxx
Driver : xxxxxxxxxxxxxxxxxxxxx
Ver : xxxxxxxxxxxxxxxxxxxxx
Addr VT : xxxxxxxxxxxxxxxxxxxxx
Error : xxxxxxxxxxxxxxxxxxxxx
Right=next page Enter=settings page
There is one of these pages for each communication port; you can move
between the various pages by pressing .

Enter
If you press while displaying this page you can access the page for set-
ting the clock and the contrast.
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
Right=next page Enter=set
PgUp PgDn
In order to access the contrast setting, use or to select the SET

Enter
CONTRAST option that is displayed in reverse colors and press ; the
following mask will appear:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9
CONTRAST : ##
Up/Down=change Enter=memo
PgUp PgDn
Enter
Use and/or to effect any variation and for the confirmation.
PgUp PgDn
To be able to set the clock use or to select the SET CLOCK option
Enter
that is displayed in reverse colors and press ; the following mask will
appear:

ries).
hh:mm:ss dd/mm/yy
Lf/Rt=select Up/Dw=change Enter=memo
PgUp PgDn
Use and/or to select the field and and/or to effect any

Enter
variation; use to confirm.
Enter
To use the Memory Card either switch on the VT with held down or, if
shift Enter
the VT is already on, press + together; in both cases it will be nec-
essary to wait a moment before the following mask appears on the VT:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

9-19
VT300 TRANSFER PAGE

Press F3=MemoCARD (if the key is not on screen, see Page 9-15) and
the following mask will appear:
MEMORY CARD MENU
F1= BACKUP F2= RESTORE
F3= ERASE F4= EXIT
For the meaning and function of the keys see Chapter 33 -> Memory card.
PR ERR

COM BROKEN

Esc
When is pressed you quit the display of information regarding the
driver.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 9
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-1
Contents Page
Functions 10-4
Front view 10-8
Rear view 10-11
Accessories 10-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10
F12 F16
F13 F17
F14 F18
F15 F19
VT310W X0 Power Battery
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11
. V Y +
F20 F21 PgUp Clr
W Z / Spare
M P S
O 4 R 5 U 6
A D G J
Ack PgDn
Help B E H K Enter
All Ack
C 0 F 1 I 2 L 3

VT310W A0000
VT310W AP000
Display
LCD 16 Colors TFT
Resolution [pixels] 240 x 128 (5,5)
Display area size [mm] 123 x 68
Character size [mm] x 1 / x 2 / x 4 3 x 4 / 6 x 8 / 12 x 16
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
Minimum lamp-life at 25C [hours] 10000
Keyboard
Operational keys 14
Diagnostic LEDs 3
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-3

VT310W A0000
VT310W AP000
User memory
Project [Bytes] 192K + 384K (Text + Graphics)
Interfaces
Auxiliary port Connection for accessories
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1500gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10
question.

Code of terminal
VT310W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons
Circles
Command: Hardcopy
Command: Next page

Command: Page help

Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-5

Code of terminal
VT310W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences
Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10

Code of terminal
VT310W
Lines
Lists of texts
Macro field
Message field
Message help 1024
Object - Indicator
Page 1024
Page help 1024
Password 10
Pipelines (Numero/Tot bytes) 64/512
Print
Programmable fonts
Project images
Public variables of ESANET network (Number/Tolat bytes) 256/1024
Rectangles
Reports 128
Sequences - Random
128
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-7

Code of terminal
VT310W
Timer 16
Touch Area
Trend buffers 128

96 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10
Front view
1
F12 F16 3
F13 F17
2 6
F14 F18
F15 F19
7
VT310W X0 Power Battery
4 8
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11
.
5
V Y +
F20 PgUp
F21 Space
W
X 7
Z
- 8
/
= 9
Spare Clr
Esc
M P S
O 4 R 5 U 6
A D G J
Ack PgDn
Help B E H K Enter
All Ack
C 0 F 1 I 2 L 3
Key Function
1 Display
9 Alphanumeric keys
Starts input
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-9
Key Function
PgUp Page up
PgDn Page down



Clr
Esc
munication driver

Help
help or page help
Ack
All
Ack
Clr
shift + Esc
Ack
shift + All
Ack
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10
Customizing
label
1 4
2 5
3 6
3 F-key customization F1... F5 - 116 x 15
6 F-key customization F6... F11 - 134 x 15

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-11
Rear view
C D E F
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10
Position Function
B Trimmer for brightness control
C Power supply connector
D LPT port for connecting printer (Optional)
E ASP serial port for communicating with PC or other devices
F MSP serial port for communicating with PLC/PC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10


ferred to it:
Firmware
Project
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-15
lowing steps:

Enter
shift Enter

Memory Card has been inserted in the VT terminal (see Page 10-18).
The function to press depends on which port you intend to use (MSP
or ASP). The VT is now ready to receive (refer to Software Manual for
transfer procedure)
VT310 TRANSFER PAGE

Graphic controller synchronization : OK
Main FIRMWARE check : NOT PRESENT

Graphic controller FIRMWARE : ERROR
VT310 TRANSFER PAGE


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10

function
mask will appear
VT310 TRANSFER PAGE


F1=SLOW F2=FAST
transfer).
driver

Shift
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-17
Right = next page Enter = settings page

Enter
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
Up/Down = select Enter = set
PgUp PgDn

Enter
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10
CONTRAST : ##
Up/Down = change Enter = memo
PgUp PgDn
Enter
PgUp PgDn
Enter
appear:

ries).
hh:mm:ss dd/mm/yy
Lf/Rt=select Up/Down=change Enter=memo
PgUp PgDn

Enter
Enter
shift Enter
the VT is already on, press + together; in both cases it will be
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

10-19
necessary to wait a moment before the following mask appears on the VT:
VT310 TRANSFER PAGE


Press F3=MemoCARD (if the key is not on the screen, see Page 10-15)
and the following mask will appear:
MEMORY CARD MENU
F3= ERASE F4= EXIT
PR ERR

COM BROKEN

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 10
Esc
driver.
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-1
Contents Page
Functions 11-4
Front view 11-8
Rear view 11-11
Accessories 11-13
Improving display color quality 11-19

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11
V Y +
W Z /
X 7 - 8 = 9
F19 F24
M P S
N Q T
O 4 R 5 U 6
F20 F25
D G J
E H K
F 1 I 2 L 3
F21 F26
A .
shift B
C 0
F22 F27
space
F23 F28
Info Hist Help

VT320W Alarm
X0 Power Battery
Ack PgUp Clr

All Ack Esc
F1 F2 F3 F4 F5 F6 F7 F8 F9
PgDn
Enter
F10 F11 F12 F13 F14 F15 F16 F17 F18

VT320W A0000
VT320W AP000
Display
LCD 16 Colors TFT
Display area size [mm] 115,6 x 87
Character matrix in text mode [pixels] 8 x15 / 16 x 30 / 32 x 60
Character size [mm] x 1 / x 2 / x 4 2,8 x 5,2 / 5,6 x 10,4 / 11,2 x 20,8
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
Keyboard
Operational keys 13
Diagnostic LEDs 3
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-3

VT320W A0000
VT320W AP000
User memory
Project [Bytes] 192K + 832K (Text+ Graphics)
Interfaces
Auxiliary port Connection of accessories
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 2000gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11
question.

Code of terminal
VT320W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons
Circles
Command: Hardcopy
Command: Next page

Command: Page help

Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-5

Code of terminal
VT320W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences
Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11

Code of terminal
VT320W
Lines
Lists of texts
Macro field
Message field
Message help 1024
Object - Indicator
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
128
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-7

Code of terminal
VT320W
Timer 16
Touch Area
Trend buffers 128

112 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11
Front view
2 1 3 8
V Y +
W Z /
X 7 - 8 = 9
F19 F24
M P S
N Q T
O 4 R 5 U 6
F20 F25
D G J
E H K
F 1 I 2 L 3
F21 F26
A .
shift B
C 0
F22 F27
space
F23 F28
Info Hist Help

VT320W Alarm
X0 Power Battery
Ack PgUp Clr

All Ack Esc
F1 F2 F3 F4 F5 F6 F7 F8 F9
PgDn
Enter
F10 F11 F12 F13 F14 F15 F16 F17 F18
4 5 6 7
Key Function
1 Display
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-9
Key Function
8 Alphanumeric keys
Starts input
PgUp Page up
PgDn Page down



Clr
Esc
munication driver

Help
help or page help
Ack
All Ack Acknowledgment of ISA alarms on display
Clr
shift + Esc
Ack
shift + All Ack Acknowledges all ISA alarms
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11
Customizing
label
1 4

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-11
Rear view
A B
C D E F
Position Function
B Trimmer for brightness control
C Power supply connector
E ASP serial port for communicating with PC or other devices
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-13


ferred to it:
Firmware
Project
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11
lowing steps:

Switch on the VT; when the message [WAIT FOR BOOT FORCED] is
Enter
shift Enter
displayed, press or with the VT on press together + ; in
either case wait a moment

transfer procedure)
VT320 TRANSFER PAGE


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-15
VT320 TRANSFER PAGE



function
mask will appear
VT320 TRANSFER PAGE


F1=SLOW F2=FAST
transfer).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11
driver

Shift

Enter
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-17
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
PgUp PgDn
In order to access the contrast setting, use or to select the SET CON-
Enter
TRAST option that is displayed in reverse colors and press ; the following
mask will appear:
CONTRAST : ##
PgUp PgDn
Enter
PgUp PgDn
Enter
appear:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11

ries).
hh:mm:ss dd/mm/yy
Lf/Rt=select Up/Down=change Enter=memo
PgUp PgDn

Enter
Enter
shift Enter
VT320 TRANSFER PAGE


Press F3=MemoCARD (if the key is not on screen, see Page 11-14); and
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

11-19
the following mask will appear:
MEMORY CARD MENU
F3= ERASE F4= EXIT
PR ERR

COM BROKEN

Esc
driver.
Improving To improve the color quality, adjust the contrast of the display: if the colors
display color are too dark increase the contrast; if, on the other hand, the colors are too
quality light, decrease the contrast.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 11
the value.
We advise this to be done at typical room temperature and with the terminal
at operating temperature (about 30 minutes after switching on and with the
screen saver disabled - see Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-1
Contents Page
Functions 12-4
Front view 12-8
Profibus-DP series rear view 12-10
Ethernet series rear view 12-12
Accessories 12-14
Methods of mounting 12-14
Calibration of Touch Screen 12-15
Introducing the MAC address 12-18

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12

VT155W 00000
VT155W 000DP
VT155W 000CN
VT155W 000ET
Display
LCD 4 tones of grey STN
LCD 16 Colors TFT
Touch screen Matrix 20 x 8 (Cell:12x16 pixels)
Resolution [pixels] 240 x 128 (4)
Rows x characters 16 x 40 / 8 x 20 / 4 x 10 - 21 x 30* / 10 x 15* / 5 x 7*
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
*) vertical mounting
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-3

VT155W 00000
VT155W 000DP
VT155W 000CN
VT155W 000ET
User memory
Project [Bytes] 640K (Text + Graphics)
Data memory [Bytes] 16K (Flash EPROM)
Interfaces
Auxiliary port Connections for accessories
Accessories
Clock
Clock Hardware (with Supercapacitor - Min.72h
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 500gr
Dimensions
External W x H x D [mm] 166 x 100 x 39,6
Certification
Certifications and approvals CE, cULus
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12
question.

Code of terminal
VT155W
Alarm field
Alarm help 256
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 160 x page
Circles

Command: Hardcopy
Command: Next page
Command: Page help
Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-5

Code of terminal
VT155W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12

Code of terminal
VT155W
Lines
Lists of texts

Macro field
Message field
Message help 256
Object - Indicator
Page 64
Page help 64
Password 10

Print
Programmable fonts
Project images

Rectangles
Reports 32
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-7

Code of terminal
VT155W
Timer 32
Touch Area 24
Trend buffers

32 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12
Front view
All buttons and signals are defined using the programming software (see
Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-9
Standard
series rear
view
B C
Position Function
B ASP serial port for communicating with PC or other devices
C MSP serial port for communicating with PLC/PC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12
Profibus-DP
series rear
view
B C
Position Function
C Serial port for network communication
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-11
CAN series
rear view
B C
Position Function
C CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12
Ethernet
series rear
view
B C
Position Function
Ethernet network 10/100Mbit RJ45 (For the diagnostic mode of

C
the LEDs see Chapter 30 -> Ethernet port)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12


Methods of There are two ways of mounting the VT155 on the container, horizontally
mounting or vertically. Once you have chosen the direction that means you can see
the project properly and you are in the project creation phase, choose the
terminal with the same orientation (see Software Manual Chapter 5 ->
New).
Once the orientation has been defined, you are recommended not
to change it, as the project created could then become unusable.
To orientate the terminal correctly use the logo on the front fascia
as a reference.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-15
Below are listed the terminals with their respective correct orientations.
Upper part
Horizontal mounting Vertical mounting
Calibration of The screen of VT155W is made of resistive, sensitive glass; for this type of
Touch Screen glass to work properly it requires a calibration procedure (the terminal is
already calibrated when supplied), that is, the resistive area of the glass
has to be adjusted to the visible are of the display.
Should it be thought necessary to repeat the calibration procedure this can

be done by following the instructions set out below.
The procedure must be carried out with great care as the preci-
sion of the keys area depends on the calibration.
How to perform the calibration procedure:
Make sure the VT is not connected to the power supply

Remove the back cover
Identify jumper J1
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12
J1
C
3
2
1
J1
Position J1 on pins 2-3 (C)

Reconnect the power supply and switch on the terminal; the following
mask appears
Touch screen calibration

Press bottom left point
Touch the corner indicated in the figure; then the following page appears
on screen

Press top right point
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-17
Touch the corner indicated in the figure to complete the calibration pro-
cedure; the following page now appears

Press bottom right point
Wait a few moments until the VT displays either the following mask or
the project page (the page may be slightly different in its wording
depending on which series the terminal belongs to)
VT155W TRANSFER PAGE
Main BOOT and RAM check : OK

Main FIRMWARE check : OK
SELECT: MSP ASP EXIT
Switch off the terminal

Reposition J1 on pins 1-2
Replace the back cover
Switch on the terminal again
The calibration procedure has finished; if the calibration has be carried out
wrongly or imprecisely, repeat the procedure.

Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12

Introducing This paragraph relates only to the Ethernet series. The Media Access Control
the MAC (MAC) address unambiguously identifies each terminal connected in the Ether-
address net network. The terminal is acquired with the address already programmed
and is shown on the display of the terminal in the transfer page.
VT155W ETHERNET TRANSFER PAGE

MAC addr:
00.0E.0E.xx.xx.xx
The MAC address is permanently memorized in the terminal, but should it

be necessary to execute an aided BOOT update (see Software Manual
Chapter 14 -> BOOT update) the address is lost.
This operation must be carried out only with the advice of the
ESA Customer Care Department.
Terminals with no valid MAC address when switched present a mask for its
insertion. If no MAC address belonging to the terminal is available, pro-
ceed as follows:
Check that the VT is not connected to the power supply.

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-19
Locate the label carrying the MAC address
00.0E.0E
xx.xx.xx
00.0E.0E
xx.xx.xx
Make a note of the number on the label (e.g. 00.0E.0E.00.00.01)
00.0E.0E -> fixed part that identifying as an ESA product

xx.xx.xx -> variable part different for each terminal
Reconnect the power supply to the terminal and, if necessary, calibrate

the touch screen (see Page 12-15)
The following mask appears; introduce the address previously noted
down (e.g. 00.0E.0E.00.00.01)
Enter a valid MAC address:

00.0E.0E.00.00.00
ESC
Use the arrow to make the setting. Once the address has been con-
firmed the following page is displayed
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12

MAC addr:
00.0E.0E.00.00.01
The procedure is now terminated.
Should a wrong MAC address have been inserted contact the ESA
Customer Care Department.
A wrong address could give rise to an error of conflict between VT

terminals in the Ethernet network.
ferred to it:
Firmware
Project
lowing steps:

Switch on the VT and wait for the following mask to appear
Press one after the other the diagonally opposite corners free of settable
objects or buttons (at least one corner needs to be free)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-21
and wait a moment, or, using the appropriate button (see Page 12-24),
till the VT displays the following mask

Choose the port you intend to use for the transfer (MSP or ASP); touch
the relevant on the display. The following mask will appear

SELECT: REMOTE LOCAL EXIT

modem or PC if you intend to use a serial port; touch the relevant on
the display
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12
mask will appear

SELECT: SLOW FAST
(Slow=9600bit/sec or Fast=38400bit/sec), touch the relevant on the display.
The VT is now ready to receive (see Software Manual for the transfer).
driver

Press two diagonally opposed angles that are free of any settable objects
or buttons (at least one angle must be free)
and you will see
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-23
Port : xxxxxxxxxxxxxxxxxxxxx PROG

Ver : xxxxxxxxxxxxxxxxxxxxx TRAN
Addr VT : xxxxxxxxxxxxxxxxxxxxx PAGE
ESC
There is one of these pages for each communication port; movement
between the various pages is effected by pressing .
From this page you can:
Set the clock and the contrast

Prepare the VT to receive the program
Setting the clock and the contrast:
To set the clock and the contrast, while displaying the above illus-
PROG
trated page, press ; the following mask appears
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
To set the contrast touch the words SET CONTRAST on the display;
you will see the following mask
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 12
CONTRAST : ##
ESC
Use the arrow for any variation (see Chapter 36 -> Operation of
terminal with touch screen).
To set the clock touch the words SET CLOCK on the display; the
following mask appears
hh:mm:ss dd/mm/yy
ESC
Prepare the VT to receive the program:
To prepare the VT to receive the program, while displaying the

TRAN
PAGE
driver information page (see Page 12-22), press , and you will
see the following mask
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

12-25

To proceed see Page 12-20.
Possible error messages that may be encountered in the driver information

page are:
PR ERR

COM BROKEN

ESC
driver.
that moment. Increase the value to darken the display; to lighten it, decrease
the value.
at operating temperature (about 30 minutes after switching on).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-1
Contents Page
Functions 13-4
Front view 13-8
Rear view 13-11
Accessories 13-13

This chapter consists of a total of 20 pages.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13
Hist
Ack
Info Help All
Ack
Alarm
F13 F21
Space
A C E
B D F
F14 F22
G I K M
H J L N
F15 F23 O Q S U
P R T V
F16 F24 W Y < >

X Z , .
F17 F25
_
; * (
- 7 8 9
F18 F26
+ : % [
= 4 5 6
F19 F27
) / \ ]
0 1 2 3
F20 F28
PgUp
Ctrl Spare Clr
VT330W Power Battery

Alt
X0
PgDn
Tab Enter
Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 Shift

VT330W APM00
VT330W APS00
VT330W APT00
Display
LCD Monochromatic STN
LCD 256 Colors TFT
196 x 148
211,2 x 158,4
Software
Contrast adjustment
Backlighting
Led
Type
Lamp CCFL
Keyboard
Operational keys 19
Diagnostic LEDs 3
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-3

VT330W APM00
VT330W APS00
VT330W APT00
User memory
Memory Card for expansion 4Mb (Only for Graphics)
Interfaces
Auxiliary port Connection of accessories
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Protection fuse 5x20mm - 1,25A Quick Blow F
Weight 4000gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13
question.

Code of terminal
VT330W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons
Circles
Command: Hardcopy
Command: Next page

Command: Page help

Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-5

Code of terminal
VT330W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences
Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13

Code of terminal
VT330W
Lines
Lists of texts
Macro field
Message field
Message help 1024
Object - Indicator 256
Object - Potentiometer knob 256
Object - Selector knob 256
Object - Sliding potentiometer 256
Object - Sliding selector 256
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
128
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-7

Code of terminal
VT330W
Timer 32
Touch Area
Trend buffers 128
Variables: Threshold variables 304 x
Variables: Floating Point numerical variables pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13
Front view
4 1 5
Hist
Ack
Info Help All
Ack
Alarm
F13 F21
Space
A C E
B D F
F14 F22
G I K M
H J L N
F15 F23 O Q S U
P R T V
F16 F24 W Y < >

X Z , .
2
F17 F25
_
; * (
- 7 8 9
F18 F26
+ : % [
= 4 5 6
F19 F27
) / \ ]
0 1 2 3
F20 F28
PgUp
Ctrl Spare Clr
VT330W Power Battery

Alt
X0
PgDn
Tab Enter
Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 Shift
3 6 7 8
Key Function
1 Display
2 Alphanumeric + operative keys
3 F-keys with no LED
Starts input
PgUp Page up
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-9
Key Function
PgDn Page down




Esc
munication driver
Hist
Displays ISA alarms
Alarm

Help
help or page help
Ack
All
Ack
Ctrl No predefined function
Tab No predefined function
Alt No predefined function
Clr In setting phase restores the initial value of the field
shift + Ack
All
Ack
Hist
shift + Displays the contents of the alarm buffer
Alarm
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13
Customizing
label
1 2

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-11
Rear view
Position Function
B LPT port for connecting printer
C ASP serial port for communicating with PC or other devices
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-13


ferred to it:
Firmware
Project
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13
lowing steps:

Switch on the VT; when the message [WAIT FOR BOOT FORCED] is
Shift Enter
Enter
displayed, press , or with the VT on press together + ; in
either case wait a moment

transfer procedure)

F1=MSP F2=ASP F3=MemoCARD ENTER=Prj
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-15


function
mask will appear

F1=SLOW F2=FAST
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13
transfer).
driver

Shift

Enter
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-17
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
PgUp PgDn

Enter
CONTRAST : ##
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13
PgUp PgDn
Enter
Use and/or to effect any variation; use for the confirmation.
PgUp PgDn
Enter
appear:

ries).
hh:mm:ss dd/mm/yy
Left/Right = select Up/Down = change Enter = memo
PgUp PgDn

Enter
Enter
shift Enter
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

13-19

F1=MSP F2=ASP F3=MemoCARD ENTER=Prj
Press F3=MemoCARD (if the key is not on screen, see Page 13-14); the
MEMORY CARD MENU
F1= Backup ALL F5= Restore ALL

F2= Backup FW/PRJ F6= Restore FW/PRJ
F3= Backup RECIPES F7= Restore RECIPE
F4= Backup ALARMS F8= Restore ALARMS
F9= EXIT
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 13
PR ERR

COM BROKEN

Esc
driver.
the value.
This parameter has no effect when a TFT display is used. This

kind of technology does not need adjustment.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-1
Contents Page
Functions 14-4
Front view 14-8
Accessories 14-12
Methods of mounting 14-12

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14

VT185W 00000
VT185W 000ET
Display
LCD 16 Colors TFT
Touch screen Matrix 20 x 16 (Cell:16 x15 pixels)
Rows x characters 16 x 40 / 8 x 20 / 4 x 10 - 21 x 30* / 10 x 15* / 5 x 7*
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-3

VT185W 00000
VT185W 000ET
User memory
Project [Bytes] 960K (Text + Graphics)
Interfaces
Accessories
Clock
Clock Hardware (with Supercapacitor - Min.72h Typically130h)
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Protection fuse Self-resetting
Weight 500gr
Dimensions
Certification
Certifications and approvals CE, cULus
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14
question.

Code of terminal
VT185W
Alarm field
Alarm help 256
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 320 x page
Circles

Command: Hardcopy
Command: Next page
Command: Page help
Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-5

Code of terminal
VT185W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14

Code of terminal
VT185W
Lines
Lists of texts

Macro field
Message field
Message help 256
Page 150
Page help 150
Password 10

Print
Programmable fonts
Project images

Rectangles
Reports 32
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-7

Code of terminal
VT185W
Timer 32
Touch Area 24
Trend buffers 128

48 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14
Front view
Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-9
Standard
series rear
view
B C
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14
Ethernet
series rear
view
B C
Position Function

C
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-11
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14


Methods of There are two ways of mounting the VT185W on the container, horizon-
mounting tally or vertically. Once you have chosen the direction that means you can
see the project properly and you are in the project creation phase, choose
the terminal with the same orientation (see Software Manual Chapter 5 ->
New).
Once the orientation has been defined, you are recommended not
to change it, as the project created could then become unusable.
To orientate the terminal correctly use the logo on the front fascia
as a reference.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-13
Below are listed the terminals with their respective correct orientations.
Upper part
Horizontal mounting Vertical mounting


Identify jumper J1
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14
C
3
2
1
J1

mask appears

on screen

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-15



405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14

MAC addr:
00.0E.0E.xx.xx.xx

ceed as follows:

00.0E.0E
xx.xx.xx
00.0E.0E
xx.xx.xx

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-17

down (e.g. 00.0E.0E.00.00.01)

00.0E.0E.00.00.00
ESC

MAC addr:
00.0E.0E.00.00.01

ferred to it:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14
Firmware
Project
lowing steps:


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-19
the relevant on the display. The following mask will appear

SELECT: REMOTE LOCAL EXIT

the display
mask will appear

SELECT: SLOW FAST
(Slow=9600bit/sec or Fast=38400bit/sec), touch the relevant on the display.
The VT is now ready to receive (see Software Manual for the transfer).
driver
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14

and you will see

ESC
Set the clock

Setting the clock:
To set the clock, while displaying the above illustrated page, press
PROG
; the following mask appears
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

14-21
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
hh:mm:ss dd/mm/yy
ESC

TRAN
PAGE

To proceed see Page 14-18.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 14

page are:
PR ERR

COM BROKEN

ESC
driver.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-1
Chapter 15 Video terminal VT505H
Contents Page
Functions 15-5
Front view 15-9
Rear view 15-10
Accessories 15-12
Connection cable 15-12
Adjusting holding strap for grip 15-12

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15
15-2 Video terminal VT505H
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10

VT505H 00000
VT505H 000CN
Display
LCD 4 tones of blue STN
LCD 16 Colors TFT
Rows x characters 16 x 40 / 8 x 20 / 4 x 10
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
1 Using the VTHCB card (see Chapter 33 -> Page 9)
2 - RS232 only
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-3

VT505H 00000
VT505H 000CN
Keyboard
User memory
Interfaces
MSP (Multi-serial port) RS232/RS422/RS485/TTY-20mA 2 1
Accessories
Clock
Clock Software (no back-up battery)
Networks
Profibus-DP
Network server
ESA-Net
Network client
2 - RS232 only
Wrapping
Type Antiflame PC/ABS halogen-free (UL94 5VA at 2.5mm)
Drop test 1 m.
Connection cable
Type Antiflame shielded cable halogen and silicone-free
Radius of curve (moving/fixed) 120mm/60mm
Conductors (number/section) 25x0,25mmq (AWG24)
System shut-down button
Positions 2 (Normal - Pushed)
Contacts 1 NC + 1 NC (NC1/NC2 + NC3/NC4)
Maximum tension 30Vdc
Maximum/minimum current 500mA/5mA
Conforms to the following standard(s) EN 60947-5-1, UL-508, CSA 22.2. No. 14)
Enabling button
Positions 3 (Normal - Pushed - Panic)
Contacts 1 NC/NO + 1 NC/NO (NC1/NO1/C1 + NC2/NO2/C2)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15

Conforms to the following standard(s) IEC 60947-5-1, EN 60947-5-1, JIS C8201-5-1, UL-508, CSA 22.2. No. 14
ISO12100/EN292, IEC60204-1/EN60204-1,
Approval(s)
ISO11161/prEN11161, ISO10218/EN775, ANSI/RIA R15.06
Technical data
Protection level (Certificated) IP65
Weight (with cable length 10m) 3000gr
Dimensions
External W x H x D [mm] See on Page 33-8
Cut-out W x H [mm] --
Certification
Certifications and approvals CE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-5
question.

Code of terminal
VT505H
Alarm field
Alarm help
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 320 x page
Circles

Command: Hardcopy
Command: Next page
Command: Page help

Command: Report

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15

Code of terminal
VT505H


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences


Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-7

Code of terminal
VT505H
Lines
Lists of texts

Macro field
Message field
Message help 256
Object - Indicator
Page 128
Page help 128
Password 10

Print
Programmable fonts
Project images

Rectangles
Reports
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15

Code of terminal
VT505H
Timer 32
Touch Area 24
Trend buffers

34 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-9
Front view
1 2 3
F1 F6
F2 F7
6 F3 F8
F4 F9
F5 F10
5 4
Key Function
1 Command and/or signal unit
System shut-down button (Conforms to the following stan-

2
dard(s): EN 60947-5-1, UL-508, CSA 22.2. No. 14)
4 F-keys
5 F-keys
6 Adjustable gripper belt
Other buttons and signals are defined using the programming software (see
Software Manual).
The system shut-down button and the enabling button do NOT

guarantee the operatrs complete personal safety. Be sure to
design your system so that is ensures the operators complete personal
safety.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15
Rear view
A B C D
Position Function
A Housing for wall-fixing hook
B Identification label
C Housing for wall-fixing hook
Enabling button (Conforms to the following standard(s): IEC

60947-5-1, EN 60947-5-1, JIS C8201-5-1, UL-508, CSA 22.2. No.
D
14) (Approval(s): ISO12100/EN292, IEC60204-1/EN60204-1,
ISO11161/prEN11161, ISO10218/EN775, ANSI/RIA R15.06)

safety.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-11
Dimensions
and Cut-out
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15
For VT mounting instructions see Chapter 29 -> Mounting the terminal

within the container.


Connection The terminal is provided with a 10m long (AWG24) 25x0.25mmq shielded
cable cable already attached (see Chapter 32 -> Connection cable for H Series
terminals).
Adjusting The strap can be altered to adjust the grip for different hand sizes. To alter
holding strap strap:
for grip
Open the leather cover
Detach the strap ends
Adjust the holding strap length
Secure strap ends again
Close leather cover
Calibration of The screen of VT505H is made of resistive, sensitive glass; for this type of

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-13
Switch on the terminal; the following mask appears
F1 VT5xx HANDHELD TRANSFER PAGE F6
F2 F7
*** WAITING FOR BOOT FORCED ***

F3 F8
F4 F9
F5 F10
To access the calibration page, touch the message ***WAITING FOR

BOOT FORCED*** three to six times in quick succession
F1 F6
F2 F7
F3 Press bottom left point F8
F4 F9
F5 F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15
on screen
F1 F6
F2 F7
F3 Press top right point F8
F4 F9
F5 F10
F1 F6
F2 F7
F3 Press bottom right point F8
F4 F9
F5 F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-15

F2 Main FIRMWARE check : OK F7
F3 *** WAIT FOR BOOT FORCED ***

F8
F4 F9
F5 F10
Wait for the start-up of the VT to be completed
ferred to it:
Firmware
Project
lowing steps:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15

F1 HANDHELD TRANSFER PAGE F6

F2 F7
F3 F8
*** WAIT FOR BOOT FORCED ***
F4 F9
F5 F10

F3 F8
SELECT: MODEM PC EXIT
F4 F9
F5 F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-17

the display
mask will appear

F3 F8
SELECT: SLOW FAST
F4 F9
F5 F10
fer (Slow=9600bit/sec or Fast=38400bit/sec), touch the relevant on the
display. The VT is now ready to receive (see Software Manual for the trans-
fer).
driver Serial ports present

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10
and you will see
F1 Port : xxxxxxxxxxxxxxxxxxxxx PROG F6

F2 Ver : xxxxxxxxxxxxxxxxxxxxx F7
TRAN
F3 Error : xxxxxxxxxxxxxxxxxxxxx F8
F4 F9
F5 ESC F10

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-19
PROG
F1 F6
SET CONTRAST : ##
F2 F7
F3 SET CLOCK : F8
ddd,dd/mm/yy
hh:mm:ss
F4 F9
F5 ESC F10
F1 F6
F2 CONTRAST : ## F7
F3 F8
F4 F9
F5 ESC F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15
hh:mm:ss dd/mm/yy
F1 F6
F2 F7
ESC
F3 F8
F4 F9
F5 F10

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

15-21
F2 F7
F3 *** WAITING FOR DOWNLOAD FROM MSP *** F8
F4 F9
F5 F10
The VT terminal is now ready to receive (consult Software Manual

for information on the transmission procedure).

page are:
PR ERR

COM BROKEN

ESC
driver.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 15
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-1
Contents Page
Functions 16-4
Front view 16-8
Accessories 16-13

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
V T505W

VT505W 00000
VT505W 000DP
VT505W 000CN
VT505W 000ET
Display
LCD 16 Colors TFT
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-3

VT505W 00000
VT505W 000DP
VT505W 000CN
VT505W 000ET
User memory
Interfaces
Accessories
Clock
Clock Software (no back-up battery)
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1400gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
question.

Code of terminal
VT505W
Alarm field
Alarm help
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 320 x page
Circles

Command: Hardcopy
Command: Next page
Command: Page help

Command: Report

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-5

Code of terminal
VT505W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16

Code of terminal
VT505W
Lines
Lists of texts

Macro field
Message field
Message help 256
Object - Indicator
Page 128
Page help 128
Password 10

Print
Programmable fonts
Project images

Rectangles
Reports
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-7

Code of terminal
VT505W
Timer 32
Touch Area 24
Trend buffers

34 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
Front view
V T505W
Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-9
Standard
series rear
view
A
B
Position Function
B MSP serial port for communicating with PLC/PC
C PROFIBUS-DP serial port for network communication (Option)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
CAN series
rear view
A
B
Position Function
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-11
Ethernet
series rear
view
C B
Position Function

C
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-13



be done (terminal Rev. 2 or above) by following the instructions set out
below.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16

Identify jumper J1
Standard, Can
Ethernet J1 C
1 2 3

mask appears

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-15
on screen


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
VT505 TRANSFER PAGE



Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-17


MAC addr:
00.0E.0E.xx.xx.xx

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
ceed as follows:

00.0E.0E
xx.xx.xx
00.0E.0E
xx.xx.xx


down (e.g. 00.0E.0E.00.00.01)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-19

00.0E.0E.00.00.00

MAC addr:
00.0E.0E.00.00.01

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
ferred to it:
Firmware
Project
lowing steps:

VT505 TRANSFER PAGE

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-21
The VT is now ready to receive (see Software Manual for information on

the transmission procedure)
VT505 TRANSFER PAGE

*** WAITING FOR DOWNLOAD FROM MSP ***
VT505 TRANSFER PAGE


the display
mask will appear
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
VT505 TRANSFER PAGE

SELECT: SLOW FAST`
fer).

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-23
and you will see

ESC

PROG
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
CONTRAST : ##
ESC
hh:mm:ss dd/mm/yy
ESC

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

16-25
VT505 TRANSFER PAGE


page are:
PR ERR

COM BROKEN

ESC
When is pressed you quit the display of information regarding the driver.
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 16
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-1
Contents Page
Functions 17-4
Front view 17-8
Accessories 17-13

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17

VT515W 00000
VT515W 000DP
VT515W 000CN
VT515W 000ET
Display
LCD 16 Colors TFT
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-3

VT515W 00000
VT515W 000DP
VT515W 000CN
VT515W 000ET
User memory
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1400gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
question.

Code of terminal
VT515W
Alarm field
Alarm help 256
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 320 x page
Circles

Command: Hardcopy
Command: Next page
Command: Page help

Command: Report

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-5

Code of terminal
VT515W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17

Code of terminal
VT515W
Lines
Lists of texts

Macro field
Message field
Message help 256
Object - Indicator
Page 128
Page help 128
Password 10

Print
Programmable fonts
Project images

Rectangles
Reports
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-7

Code of terminal
VT515W
Timer 32
Touch Area 24
Trend buffers

34 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
Front view
Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-9
Standard
series rear
view
A
B
Position Function
C PROFIBUS-DP serial port for network communication (Option)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
CAN series
rear view
A
B
Position Function
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-11
Ethernet
series rear
view
C B
Position Function

C
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-13



405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17

Identify jumper J1
Standard, Can
Ethernet J1 C
1 2 3

mask appears

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-15
on screen


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
VT515 TRANSFER PAGE



Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-17


MAC addr:
00.0E.0E.xx.xx.xx

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
ceed as follows:

00.0E.0E
xx.xx.xx
00.0E.0E
xx.xx.xx


down (e.g. 00.0E.0E.00.00.01)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-19

00.0E.0E.00.00.00

MAC addr:
00.0E.0E.00.00.01

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
ferred to it:
Firmware
Project
lowing steps:

VT515 TRANSFER PAGE

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-21
The VT is now ready to receive (see Software Manual for information on

the transmission procedure)
VT515 TRANSFER PAGE

VT515 TRANSFER PAGE


the display
mask will appear
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
VT515 TRANSFER PAGE

SELECT: SLOW FAST`
fer).

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-23
and you will see

ESC

PROG
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
CONTRAST : ##
ESC
hh:mm:ss dd/mm/yy
ESC

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

17-25
VT515 TRANSFER PAGE


page are:
PR ERR

COM BROKEN

ESC
When is pressed you quit the display of information regarding the driver.
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 17
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-1
Chapter 18 Video terminal VT525H
Contents Page
Functions 18-5
Front view 18-9
Rear view 18-10
Accessories 18-12
Connection cable 18-12
Adjusting holding strap for grip 18-12

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10

VT525H 00000
VT525H 000CN
Display
LCD 16 Colors TFT
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
2 - RS232 only
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-3

VT525H 00000
VT525H 000CN
Keyboard
User memory
Interfaces
MSP (Multi-serial port) RS232/RS422/RS485/TTY-20mA 2 1
ASP-15L (Auxiliary serial port) RS232/RS485 1-2
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
2 - RS232 only
Wrapping
Type Antiflame PC/ABS halogen-free (UL94 5VA at 2.5mm)
Drop test 1 m.
Connection cable
Type Antiflame shielded cable halogen and silicone-free
Radius of curve (moving/fixed) 120mm/60mm
Conductors (number/section) 25x0,25mmq (AWG24)
System shut-down button
Positions 2 (Normal - Pushed)
Contacts 1 NC + 1 NC (NC1/NC2 + NC3/NC4)
Conforms to the following standard(s) EN 60947-5-1, UL-508, CSA 22.2. No. 14)
Enabling button
Positions 3 (Normal - Pushed - Panic)
Contacts 1 NC/NO + 1 NC/NO (NC1/NO1/C1 + NC2/NO2/C2)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18

Conforms to the following standard(s) IEC 60947-5-1, EN 60947-5-1, JIS C8201-5-1, UL-508, CSA 22.2. No. 14
ISO12100/EN292, IEC60204-1/EN60204-1,
Approval(s)
ISO11161/prEN11161, ISO10218/EN775, ANSI/RIA R15.06
Technical data
Protection level (Certificated) IP65
Weight (with cable length 10m) 3000gr
Dimensions
External W x H x D [mm] See on Page 33-8
Certification
Certifications and approvals CE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-5
question.

Code of terminal
VT525H
Alarm field
Alarm help 256
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 320 x page
Circles

Command: Hardcopy
Command: Next page
Command: Page help
Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18

Code of terminal
VT525H


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-7

Code of terminal
VT525H
Lines
Lists of texts

Macro field
Message field
Message help 256
Object - Indicator
Page 150
Page help 150
Password 10

Print
Programmable fonts
Project images

Rectangles
Reports 32
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18

Code of terminal
VT525H
Timer 32
Touch Area 24
Trend buffers

48 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-9
Front view
1 2 3
F1 F6
F2 F7
6 F3 F8
F4 F9
F5 F10
5 4
Key Function
System shut-down button (Conforms to the following stan-

2
dard(s): EN 60947-5-1, UL-508, CSA 22.2. No. 14)
4 F-keys
5 F-keys
6 Adjustable gripper belt
Other buttons and signals are defined using the programming software (see
Software Manual).

safety.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18
Rear view
A B C D
Position Function
A Housing for wall-fixing hook
B Identification label
C Housing for wall-fixing hook
Enabling button (Conforms to the following standard(s): IEC

60947-5-1, EN 60947-5-1, JIS C8201-5-1, UL-508, CSA 22.2. No.
D
14) (Approval(s): ISO12100/EN292, IEC60204-1/EN60204-1,
ISO11161/prEN11161, ISO10218/EN775, ANSI/RIA R15.06)

safety.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-11
Dimensions
and Cut-out
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18
For VT mounting instructions see Chapter 29 -> Mounting the terminal

within the container.


Connection The terminal is provided with a 10m long (AWG24) 25x0.25mmq shielded
cable cable already attached (see Chapter 32 -> Connection cable for H Series
terminals).
Adjusting The strap can be altered to adjust the grip for different hand sizes. To alter
holding strap strap:
for grip
Open the leather cover
Detach the strap ends
Adjust the holding strap length
Secure strap ends again
Close leather cover
Calibration of The screen of VT525H is made of resistive, sensitive glass; for this type of

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-13
Switch on the terminal; the following mask appears
F2 F7
*** WAITING FOR BOOT FORCED ***

F3 F8
F4 F9
F5 F10
To access the calibration page, touch the message ***WAITING FOR

BOOT FORCED*** three to six times in quick succession
F1 F6
F2 F7
F3 Press bottom left point F8
F4 F9
F5 F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18
on screen
F1 F6
F2 F7
F3 Press top right point F8
F4 F9
F5 F10
F1 F6
F2 F7
F3 Press bottom right point F8
F4 F9
F5 F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-15

F3 *** WAIT FOR BOOT FORCED ***

F8
F4 F9
F5 F10
Wait for the start-up of the VT to be completed
ferred to it:
Firmware
Project
lowing steps:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18

F1 HANDHELD TRANSFER PAGE F6

F2 F7
F3 F8
F4 F9
F5 F10

F3 F8
F4 F9
F5 F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-17
the relevant on the display. The VT is now ready to receive (refer to
Software Manual for transfer procedure).

F3 F8
F4 F9
F5 F10

the display
mask will appear
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18

F3 F8
SELECT: SLOW FAST
F4 F9
F5 F10
fer).

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-19
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10
and you will see
F1 Port : xxxxxxxxxxxxxxxxxxxxx PROG F6

F2 Ver : xxxxxxxxxxxxxxxxxxxxx F7
TRAN
F3 Error : xxxxxxxxxxxxxxxxxxxxx F8
F4 F9
F5 ESC F10

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18
PROG
F1 F6
SET CONTRAST : ##
F2 F7
F3 SET CLOCK : F8
ddd,dd/mm/yy
hh:mm:ss
F4 F9
F5 ESC F10
F1 F6
F2 CONTRAST : ## F7
F3 F8
F4 F9
F5 ESC F10
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-21
hh:mm:ss dd/mm/yy
F1 F6
F2 F7
ESC
F3 F8
F4 F9
F5 F10

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 18
F2 F7
F3 *** WAITING FOR DOWNLOAD FROM MSP *** F8
F4 F9
F5 F10
The on-screen to press depends on the port you intend to use (MSP
or ASP). The VT terminal is now ready to receive (consult Software
Manual for information on the transmission procedure).


page are:
PR ERR

COM BROKEN

ESC
driver.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

18-23
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-1
Contents Page
Functions 19-4
Front view 19-8
Accessories 19-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19

VT525W 00000
VT525W 000DP
VT525W 000CN
VT525W 000ET
Display
LCD 16 Colors TFT
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-3

VT525W 00000
VT525W 000DP
VT525W 000CN
VT525W 000ET
User memory
Interfaces
Accessories
Clock
Clock Hardware (with Supercapacitor - Min.72h
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1400gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19
question.

Code of terminal
VT525W
Alarm field
Alarm help 256
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 320 x page
Circles

Command: Hardcopy
Command: Next page
Command: Page help
Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-5

Code of terminal
VT525W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19

Code of terminal
VT525W
Lines
Lists of texts

Macro field
Message field
Message help 256
Object - Indicator
Page 150
Page help 150
Password 10

Print
Programmable fonts
Project images

Rectangles
Reports 32
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-7

Code of terminal
VT525W
Timer 32
Touch Area 24
Trend buffers

48 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19
Front view
Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-9
Standard
series rear
view
A
C
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19
Profibus-DP
series rear
view
Position Function
C Serial port for network communication
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-11
CAN series
rear view
Position Function
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19
Ethernet
series rear
view
C B
Position Function

C
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19



405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-15

Identify jumper J1
J1 C
1 2 3

mask appears

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19
on screen


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-17



Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19
J4 T
1 2 3


MAC addr:
00.0E.0E.xx.xx.xx

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-19
ceed as follows:

00.0E.0E
xx.xx.xx
00.0E.0E
xx.xx.xx


down (e.g. 00.0E.0E.00.00.01)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19

00.0E.0E.00.00.00

MAC addr:
00.0E.0E.00.00.01

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-21
ferred to it:
Firmware
Project
lowing steps:

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19

Software Manual for transfer procedure).


the display
mask will appear
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-23

SELECT: SLOW FAST
fer).

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19
and you will see

ESC

PROG
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-25
CONTRAST : ##
ESC
hh:mm:ss dd/mm/yy
ESC

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 19



page are:
PR ERR

COM BROKEN

ESC
driver.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

19-27
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-1
Contents Page
Functions 20-4
Front view 20-8
Accessories 20-12

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 20
VT555W
Code of terminal Characteristics of terminal

VT555W 00000
VT555W A0000
VT555W AP000
VT555W A00DP
VT555W AP0DP
VT555W 000CN
Display
LCD 16 Colors TFT
Resolution [pixels] 240 x 128
Display area size [mm] 123 x 68 (5,5)
Character size [mm] x 1 / x 2 / x 4 3 x 4 / 6 x 8 / 12 x 16
Software
Contrast adjustment
Character sets * Programmable fonts/TTF Windows
Backlighting
LED
Type
CCFL lamp
* VT555W 00000 only programmable fonts
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-3
Code of terminal Characteristics of terminal

VT555W 00000
VT555W A0000
VT555W AP000
VT555W A00DP
VT555W AP0DP
VT555W 000CN
User memory
256K + 384K (Text + Graphics)
Project [Bytes]
192K + 384K (Text + Graphics)
32K (With back-up battery)
Data memory [Bytes]
128K (With back-up battery)
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1400gr
Dimensions
Certification
* VT555W 00000 only programmable fonts
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 20
question.

Code of terminal
VT555W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 160 x page
Circles
Command: Hardcopy
Command: Next page
Command: Page help
Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-5

Code of terminal
VT555W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 20

Code of terminal
VT555W
Lines
Lists of texts

Message field
Message help 1024
Object - Indicator
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-7

Code of terminal
VT555W
Timer 32
Touch Area 48
Trend buffers 128

96 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 20
Front view
VT555W
Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-9
Standard
series rear
view
G
A
F
C D E
Position Function
B NETWORK2 serial port for network communication (Option)
C NETWORK1 serial port for network communication (Option)
ASP serial port for communicating with PC or other devices

D
(Option)
F LPT port for connecting printer (Option)
G Trimmer for brightness control
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 20
CAN series
rear view
E
A
D
B C
Position Function
B CAN serial port
D LPT port for connecting printer (Option)
E Trimmer for brightness control
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-11
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 20



Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-13

ferred to it:
Firmware
Project
lowing steps:

Switch on the VT by pressing simultaneously on two diagonally opposed
angles of the screen
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 20
VT555 TRANSFER PAGE


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-15
VT555 TRANSFER PAGE



the display
mask will appear
VT555 TRANSFER PAGE


SELECT: SLOW FAST
fer).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 20
driver

and there appears the following mask
TRAN
Ver : xxxxxxxxxxxxxxxxxxxxx PAGE
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-17

PROG
SET CONTRAST: ##
SET CLOCK:
ddd,dd/mm/yy
hh:mm:ss
ESC
CONTRAST: ##
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 20
inserted in the terminal (see Chapter 33 -> Video terminal acces-

sories).
hh:mm:ss dd/mm/yy
ESC

TRAN
PAGE
VT555 TRANSFER PAGE

Which on-screen you touch depends on the port you intend using.
The VT is now ready to receive (refer to Software Manual for infor-

mation on the transfer procedure). Once you enter this mask, you can
quit without transferring only by switching off and switching on the
VT again or by pressing the EXIT .
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

20-19

page are:
PR ERR

COM BROKEN

ESC
driver.
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

21-1
Contents Page
Functions 21-4
Front view 21-8
Rear view 21-9
Accessories 21-11

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 21

VT560W A0000
VT560W A0M00
Display
LCD 16 Colors TFT
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

21-3

VT560W A0000
VT560W A0M00
User memory
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1400gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 21
question.

Code of terminal
VT560W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 320 x page
Circles
Command: Hardcopy
Command: Next page
Command: Page help
Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

21-5

Code of terminal
VT560W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 21

Code of terminal
VT560W
Lines
Lists of texts

Macro field
Message field
Message help 1024
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

21-7

Code of terminal
VT560W
Timer 32
Touch Area 64
Trend buffers 128

112 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 21
Front view
Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

21-9
Rear view
B C
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 21
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

21-11


ferred to it:
Firmware
Project
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 21
lowing steps:

VT560 TRANSFER PAGE

Main BOOT and RAM check : WAIT

the display
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

21-13
mask will appear
VT560 TRANSFER PAGE

SELECT: SLOW FAST
fer).
driver

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 21
and you will see

ESC

Use the Memory Card
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

21-15
PROG
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
CONTRAST : ##
ESC

inserted in the terminal (see Chapter 33 -> Video terminal
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 21
accessories).
hh:mm:ss dd/mm/yy
ESC

TRAN
PAGE
VT560 TRANSFER PAGE

SELECT: MSP ASP MemoCARD EXIT
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

21-17
Using the Memory Card:
TRAN
PAGE
While displaying the driver information page, press and the fol-
lowing mask will appear:
VT560 TRANSFER PAGE

Touch the MemoCARD on the screen (if the key is not on screen,
see Page 21-12) and the following mask will appear:
MEMORY CARD MENU
BACKUP RESTORE
ERASE EXIT
For the meaning and the functions of the keys see Chapter 33 ->
Memory card.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 21

page are:
PR ERR

COM BROKEN

ESC
driver.
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-1
Contents Page
Functions 22-4
Front view 22-8
Rear view 22-9
Accessories 22-11

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 22
VT565W

VT565W A0000
VT565W AP000
VT565W A0M00
VT565W APM00
Display
LCD 256 Colors TFT
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-3

VT565W A0000
VT565W AP000
VT565W A0M00
VT565W APM00
User memory
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1400gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 22
question.

Code of terminal
VT565W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 320 x page
Circles
Command: Hardcopy
Command: Next page
Command: Page help
Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-5

Code of terminal
VT565W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 22

Code of terminal
VT565W
Lines
Lists of texts

Macro field
Message field
Message help 1024
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-7

Code of terminal
VT565W
Timer 32
Touch Area 64
Trend buffers 128

112 x pages

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 22
Front view
VT565W
Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-9
Rear view
A
F
H D E
Position Function
G Trimmer for brightness control (B&W)
H Trimmer for brightness control (Color)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 22
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-11


ferred to it:
Firmware
Project
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 22
lowing steps:

Software Manual for transfer procedure). The MemoCARD appears if
the Memory Card has been inserted in the VT (see Page 22-18)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-13
VT565 TRANSFER PAGE

VT565 TRANSFER PAGE


the display
mask will appear
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 22
VT565 TRANSFER PAGE

SELECT: SLOW FAST
fer).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-15
driver

and you will see

ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 22

Use the Memory Card
PROG
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
CONTRAST : ##
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-17

accessories).
hh:mm:ss dd/mm/yy
ESC

TRAN
PAGE
VT565 TRANSFER PAGE

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 22
TRAN
PAGE
VT565 TRANSFER PAGE

MEMORY CARD MENU
BACKUP RESTORE
ERASE EXIT
Memory card.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

22-19

page are:
PR ERR

COM BROKEN

ESC
driver.
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-1
Contents Page
Functions 23-4
Front view 23-8
Accessories 23-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23

VT575W APS00
VT575W 0PSDP
VT575W 0PSCN
VT575W 0PSET
Display
LCD 256 Colors TFT
Touch screen [cells] Matrix 40x30 (Cell:16x16 pixels)
Rows per character 30 x 80 / 15 x 40 / 7 x 20
Dimension of visible area [mm] 158 x 118
Character size [mm] x1 / x2 / x4 1,89 x 3,79 / 3,79 x 7,58 / 7,58 x 15,16
Software
Contrast adjustment
Character set Programmable fonts/TTF Windows
Backlighting
LED
Type
CCFL lamp
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-3

VT575W APS00
VT575W 0PSDP
VT575W 0PSCN
VT575W 0PSET
User memory
Project [Bytes] 960K + 6M (Text + Graphic)
Memory Card for expansion 4Mb (Only for graphic type)
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1500gr
Dimensions
External W x H x D [mm] 245,9 x 188,6 x 37,6
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23
question.

Code of terminal
VT575W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 1200 x page
Circles
Command: Hardcopy
Command: Next page
Command: Page help
Command: Report

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-5

Code of terminal
VT575W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23

Code of terminal
VT575W
Lines
Lists of texts

Macro field
Message field
Message help 1024
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-7

Code of terminal
VT575W
Timer 32
Touch Area 256
Trend buffers 128

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23
Front view
All buttons and signals are defined via the programming software (see Soft-
ware Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-9
Standard
series rear
view
A
C D
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23
Profibus-DP
series rear
view
A
C D
Position Function
D Serial port for network communication
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-11
CAN series
rear view
A
C D
Position Function
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23
Ethernet
series rear
view
A
C D
Position Function

D
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23



405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-15

Identify jumper J11
J11
C
1 2 3

mask appears
TOUCH SCREEN CALIBRATION
Please touch bottom left
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23
Touch the corner indicated in the figure; then the following page appears on screen
Please touch top right
Touch the corner indicated in the figure to complete the Calibrazione

procedure; the following page now appears
please touch bottom right
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-17
the project page


Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23
J14
1
2
3 T


Touch screen BOOT check : OK
SELECT: MSP MemoCARD EXIT
MAC addr:
00.0E.0E.xx.xx.xx
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-19

ceed as follows:

00.0E.0E
xx.xx.xx
00.0E.0E
xx.xx.xx


down (e.g. 00.0E.0E.00.00.01)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23

00.0E.0E.00.00.00
MAC addr:
00.0E.0E.00.00.01
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-21

ferred to it:
Firmware
Project
Preparation for The programme VTWIN must be used for the transfer (see Software Man-
reception ual), but the terminal must be prepared for reception.
This means carrying out the following steps:

Press one after the other two diagonally opposite corners free of settable
WAIT FOR BOOT FORCED
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23
and wait a few moments, alternatively use the button provided (see Page
23-21), until the VT displays the following mask


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-23
or PC if you intend to use a serial port; touch the relevant on the display
mask will appear

SELECT: SLOW FAST
fer).
driver

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23
and you will see

ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-25

Use the Memory Card
PROG
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23
CONTRAST: ##
ESC
hh:mm:ss dd/mm/yy
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-27

TRAN
PAGE

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 23

MEMORY CARD MENU
BACKUP RESTORE
ERASE EXIT
Memory card.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

23-29

page are:
PR ERR

COM BROKEN

ESC
driver.
the value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-1
Contents Page
Functions 24-4
Front view 24-8
Accessories 24-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24

VT580W APS00
VT580W 0PSDP
VT580W 0PSCN
VT580W 0PSET
Display
LCD 256 Colors TFT
Dimension of visible area [mm] 174,8 x 131,2
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-3

VT580W APS00
VT580W 0PSDP
VT580W 0PSCN
VT580W 0PSET
User memory
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1500gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24
question.

Code of terminal
VT580W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 1200 x page
Circles
Command: Hardcopy
Command: Next page
Command: Page help
Command: Report

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-5

Code of terminal
VT580W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24

Code of terminal
VT580W
Lines
Lists of texts

Macro field
Message field
Message help 1024
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-7

Code of terminal
VT580W
Timer 32
Touch Area 256
Trend buffers 128

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24
Front view
ware Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-9
Standard
series rear
view
A
C D
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24
Profibus-DP
series rear
view
A
C D
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-11
CAN series
rear view
A
C D
Position Function
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24
Ethernet
series rear
view
A
C D
Position Function

D
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24



405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-15

Identify jumper J11
J11
C
1 2 3

mask appears
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-17
the project page


Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24
J14
1
2
3 T


MAC addr:
00.0E.0E.xx.xx.xx
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-19

ceed as follows:

00.0E.0E
xx.xx.xx
00.0E.0E
xx.xx.xx


down (e.g. 00.0E.0E.00.00.01)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24

00.0E.0E.00.00.00
MAC addr:
00.0E.0E.00.00.01
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-21

ferred to it:
Firmware
Project

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-23
mask will appear

SELECT: SLOW FAST
fer).
driver

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24
and you will see

ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-25

Use the Memory Card
PROG
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24
CONTRAST: ##
ESC
hh:mm:ss dd/mm/yy
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-27

TRAN
PAGE

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 24

MEMORY CARD MENU
BACKUP RESTORE
ERASE EXIT
Memory card.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

24-29

page are:
PR ERR

COM BROKEN

ESC
driver.
the value.

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-1
Contents Page
Functions 25-4
Front view 25-8
Accessories 25-13

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25
VT585W

VT585W APS00
VT585W APT00
VT585W 0PSCN
Display
LCD 256 Colors TFT
211,2 x 158
Dimension of visible area [mm]
211,2 x 158,4
Software
Contrast adjustment
Backlighting
LED
Type
CCFL lamp
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-3

VT585W APS00
VT585W APT00
VT585W 0PSCN
User memory
Project [Bytes] 640K + 1792K (Text + Graphic)
Interfaces
Accessories
Clock
Hardware clock With back-up battery
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 4000gr
Dimensions
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25
question.

Code of terminal
VT585W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 1200 x page
Circles
Command: Hardcopy
Command: Next page
Command: Page help
Command: Report


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-5

Code of terminal
VT585W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25

Code of terminal
VT585W
Lines
Lists of texts

Macro field
Message field
Message help 256
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-7

Code of terminal
VT585W
Timer 32
Touch Area 256
Trend buffers 128

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25
Front view
VT585W
ware Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-9
Customizing
label
1

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25
Standard
series rear
view A
Position Function
C ASP serial port for communicating with PC or other devices
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-11
CAN series
rear view
A
Position Function
E CAN serial port
F Power supply connector
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-13



be done (terminal Rev. 5 or above) by following the instructions set out
below.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25

Identify jumpers JP5 and JP12
Position JP5 and JP12 on pins 2-3

mask appears (the number and type of mask depend on the release ver-
sion of the terminal)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-15
Release 5.0 to 5.2:
Touch screen BOOT check :

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25
Please wait
Release 5.3 or later:

current parameters : xxxx xxxx xxxx xxxx
------------------------------------------------------------------
please TOUCH bottom left
on screen
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-17

------------------------------------------------------------------
Please TOUCH top right
on screen

------------------------------------------------------------------
please TOUCH bottom right
cedure. Wait a few moments until the VT displays either the following
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25
mask or the project page


Reposition JP5 and JP12 on pins 1-2

Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-19

ferred to it:
Firmware
Project

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-21


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25
mask will appear

SELECT: SLOW FAST
fer).
driver

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-23
and you will see

ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25

Use the Memory Card
PROG
SET CONTRAST: ##
SET CLOCK:
ddd,dd/mm/yy
hh:mm:ss
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-25
CONTRAST: ##
ESC
hh:mm:ss dd/mm/yy
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25

accessories).

TRAN
PAGE

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

25-27

MEMORY CARD MENU
BACKUP RESTORE
ERASE EXIT
Memory card.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 25

page are:
PR ERR

COM BROKEN

ESC
driver.
the value.

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-1
Chapter 26 Video terminal VT585WB
Contents Page
Functions 26-4
Front view 26-8
Accessories 26-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26
26-2 Video terminal VT585WB

VT585W BPT00
VT585W BPTDP
VT585W BPTCN
VT585W BPTET
Display
LCD 256 Colors TFT
Dimension of visible area [mm] 211,2 x 158
Software
Contrast adjustment
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-3

VT585W BPT00
VT585W BPTDP
VT585W BPTCN
VT585W BPTET
Backlighting
LED
Type
CCFL lamp
User memory
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 1900gr
Dimensions
External W x H x D [mm] 336,3 x 256 x 44
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26
question.

Code of terminal
VT585W B
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 1200 x page
Circles
Command: Hardcopy
Command: Next page
Command: Page help
Command: Report

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-5

Code of terminal
VT585W B


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26

Code of terminal
VT585W B
Lines
Lists of texts

Macro field
Message field
Message help 1024
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-7

Code of terminal
VT585W B
Timer 32
Touch Area 256
Trend buffers 128

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26
Front view
ware Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-9
Standard
series rear
view A
C D
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26
Profibus-DP
series rear
view A
C D
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-11
CAN series
rear view
A
C D
Position Function
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26
Ethernet
series rear
view A
C D
Position Function

D
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26


Calibration of The screen of VT585WB is made of resistive, sensitive glass; for this type
Touch Screen of glass to work properly it requires a calibration procedure (the terminal
is already calibrated when supplied), that is, the resistive area of the glass

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-15

Identify jumper J11
J11
C
1 2 3

mask appears
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-17
the project page
VT585WB TRANSFER PAGE


Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26
J14
1
2
3 T

VT585WB ETHERNET TRANSFER PAGE

MAC addr:
00.0E.0E.xx.xx.xx
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-19

ceed as follows:

00.0E.0E
xx.xx.xx
00.0E.0E
xx.xx.xx


down (e.g. 00.0E.0E.00.00.01)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26

00.0E.0E.00.00.00
VT585WB ETHERNET TRANSFER PAGE
MAC addr:
00.0E.0E.00.00.01
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-21

ferred to it:
Firmware
Project

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-23
mask will appear

SELECT: SLOW FAST
fer).
driver

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26
and you will see

ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-25

Use the Memory Card
PROG
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26
CONTRAST: ##
ESC
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
hh:mm:ss dd/mm/yy
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-27

TRAN
PAGE

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 26

MEMORY CARD MENU
BACKUP RESTORE
ERASE EXIT
Memory card.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

26-29

page are:
PR ERR

COM BROKEN

ESC
driver.
the value.

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-1
Contents Page
Functions 27-4
Front view 27-8
Accessories 27-14

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27

VT595W APT00
VT595W 0PTDP
VT595W 0PTCN
VT595W 0PTET
Display
LCD 256 Colors TFT
Dimension of visible area [mm] 246 x 185
Character size [mm] x1 / x2 / x4 2,5 x 4,6 / 5 x 9,2 / 10 x 18,4
Software
Contrast adjustment
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-3

VT595W APT00
VT595W 0PTDP
VT595W 0PTCN
VT595W 0PTET
Backlighting
LED
Type
CCFL lamp
User memory
Interfaces
Accessories
Clock
Networks
Profibus-DP
Network server
ESA-Net
Network client
Technical data
Weight 2100gr
Dimensions
External W x H x D [mm] 336,3 x 256 x 44
Certification
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27
question.

Code of terminal
VT595W
Alarm field
Alarm help 1024
Alarm statistics
Arc
Backup/Restore
Bar data
Buttons 1200 x page
Circles
Command: Hardcopy
Command: Next page
Command: Page help
Command: Report

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-5

Code of terminal
VT595W


Date field
E-keys
Equations 32
F-keys
Free terminal
Function: Macro
Function: None
Function: Sequences

Labels

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27

Code of terminal
VT595W
Lines
Lists of texts

Macro field
Message field
Message help 1024
Page 1024
Page help 1024
Password 10
Print
Programmable fonts
Project images
Rectangles
Reports 128
Sequences - Random
Static bitmaps
System messages
Time long field
Time short field

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-7

Code of terminal
VT595W
Timer 32
Touch Area 256
Trend buffers 128

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27
Front view
ware Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-9
Standard
series rear
view A
C D
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27
Profibus-DP
series rear
view A
C D
Position Function
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-11
CAN series
rear view
A
C D
Position Function
D CAN serial port
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27
Ethernet
series rear
view A
C D
Position Function

D
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-13
Dimensions
and Cut-out
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27



405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-15

Identify jumper J11
J11
C
1 2 3

mask appears
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-17
the project page


Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27
J14
1
2
3 T


MAC addr:
00.0E.0E.xx.xx.xx
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-19

ceed as follows:

00.0E.0E
xx.xx.xx
00.0E.0E
xx.xx.xx


down (e.g. 00.0E.0E.00.00.01)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27

00.0E.0E.00.00.00
MAC addr:
00.0E.0E.00.00.01
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-21

ferred to it:
Firmware
Project

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27


405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-23
mask will appear

SELECT: SLOW FAST
fer).
driver

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27
and you will see

ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-25

Use the Memory Card
PROG
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27
CONTRAST: ##
ESC
SET CONTRAST : ##
SET CLOCK :
ddd,dd/mm/yy
hh:mm:ss
hh:mm:ss dd/mm/yy
ESC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-27

TRAN
PAGE

TRAN
PAGE
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 27

MEMORY CARD MENU
BACKUP RESTORE
ERASE EXIT
Memory card.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

27-29

page are:
PR ERR

COM BROKEN

ESC
driver.
the value.

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

28-1
Chapter 28 Inserting customized labels
Contents Page
Label 28-2
Warnings 28-2
Notes 28-4
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 28
28-2 Inserting customized labels
VT terminals are supplied with labels already set in the appropriate spaces.
If it is necessary to customize keys, the logo or the model the labels can be
replaced with the neutral ones supplied in kit with the terminal (only for
F-keys) or by inserting labels of other materials provided they conform
with the points set out below.
Failure to follow the following indications may cause damage to

the terminal.
Label The label must be of a material that is flexible and does not exceed 125m
(micrometers).
Use neither stiff materials nor glues.
Warnings Before starting to insert the customized label the following points MUST
BE observed:
Remove the label already inserted.

Follow the indications set out in the paragraph Label.
Do not use compressed air to help insert the label.
Do not use rigid or other instruments to insert the label.
Do not fold the label between the terminal and the casing. The following
figures illustrate the correct and the incorrect positions for the label.
Correct insertion:
Thickness of sticker Keyboard
Container Label Metal support
The label illustrated is free and creates no tension on the keyboard.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

28-3
INCORRECT insertion which could cause compromised adhesion:
Compromised
adhesion
Compromised
adhesion
The labels illustrated generate pressure that over time could cause the
keyboard to scollare.
The oversize part of the label must go under the back cover or in the
appropriate fixing points (the choice is determined by the type of VT
being used).
Back cover
Fixing points for

adhesives
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 28
28-4 Inserting customized labels
Notes Here are some tips to make it easier to insert the label:
Round off the corners.
If there seems to be some resistance pull the label out and reinsert it.
If more than one label is used, insert them all at the same time.
Label 1 Label 2
Take care not to exceed the total thickness permitted (see Page
28-2 -> Label).
Do not bend the label at right angles and/or do not bend them so sharply
that they might be damaged.
Slightly bend the label lengthwise to make it stiffer.
Index finger Thumb Index finger Thumb
Middle finger Middle finger
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

29-1
Chapter 29 Mounting the terminal within the container
Contents Page
Using nuts 29-2
Using hooks 29-3
Fixing using external support 29-6
Tightening the fixing screws 29-3

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 29
29-2 Mounting the terminal within the container
The VT comes supplied with the elements necessary for mounting it within
the host container and fixing the sealing gasket giving the declared level of
IP protection.
There are three kinds of terminal: those with the gasket already in place and
the mounting within the container being secured by means of nuts, and
those where the gasket is to be fitted in the installation phase and the means
of securing are hooks and those with seal already attached which are fixed
to the container using external support.
Using nuts The figure below shows the front and back views of a VT inserted in a con-
tainer. Under the figure is to be found the sequence of operations to be car-
ried out to ensure that the fixing is correct.
Cut-out of a Pre-applied
Stud
container gasket
Video Terminal Washer Nut
After preparing the container that will host the VT:
Insert the VT in the cut-out

Hold the VT against the wall
Insert first the washer then the nut into the fastener
Tighten the nuts till the gasket has a firm grip (see also Page 29-10)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

29-3
Using hooks The illustrations appearing below show in front and rear views the
sequence of actions for mounting a VT within a container.
Cut-out of a
Video Terminal
container
Centering and gripping

Gasket to be inserted
notch
After preparing the container that will host the VT:
Insert the gasket in the VT the right way round as indicated by the cen-
tering notches
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 29
Fixing hook
Screws for hooks
Prepare the fixing hooks

Thread the screws into the hook by about 10mm
Insert the VT and hold it pressed against the container

Insert the hooks into the slots following the direction indicated by the
arrow and tighten the screws as far as they go (see also Page 29-10)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

29-5
View of terminal with correct fixing.
The number and position of the hooks do not influence the fixing
procedure. The illustrations are to show the way the hooks work.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 29
Fixing using The figure below shows the hook to use to mount those VTs requiring a
external support external to the container.
support
Hook for Cross-section
mounting terminal (1) of container
Wedge to adjust
tilt of terminal (2)
Before proceeding with the explanation of the steps required to mount the
terminal it needs to be said that the hook allows the terminal to be posi-
tioned at various heights and angles, so the exact position must be defined.
To help do this, the following figure shows the maximum movement possi-
ble from the operators view point, depending on how the tilt adjustment
wedge is positioned (intermediate positions for intermediate tilt angles).
Do not use or position other than as indicated.
Do not alter the original form of the mounting hook or the tilt
adjustment wedge.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

29-7
A
0 0
B
Position Maximum movement possible relative to operators viewing level (0-0)
0-A 120mm
0-B 80mm 106mm
0-C 620mm
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 29
The hook is for fixing to a plastic or metal surface or container.

Should the terminal be fixed to a wall or suchlike, the user will be res-
posable for supplying the correct screws for the type of material in ques-
tion.
After defining the position of the support hook:
Position the hook (preferably on a smooth surface) and secure using the
screws supplied. If a 3MA threaded hole is made, just use the screws,
otherwise use the washer and nut.
Fixing with screws in 3MA Fixing with screws,

threaded holes washers and nuts
The tilt adjustment wedge must be positioned (position 0-A, 0-B or inter-
mediate) using the same criterion as with the previous point
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

29-9
Fixing with screws in 3MA Fixing with screws,

threaded holes washers and nuts
The VT can now be inserted following the direction of the arrows.
Final
position
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 29
Tightening the For the best possibile grip of the basket to the container, you are advised:
fixing screws
To respect the screwing sequenze illustrated.
Using nuts
6
1 4 1 4
3 2 3 2
5
8 6 10 6 8
1 4 1 4
3 2 3 2
5 7 7 5 9
Using hooks
1 4
1 4
3 2
3 2
10 6 8
1 6 4
1 4
3 2
3 5 2
7 5 9
Initially tighten the fixing screws with moderate pressure so as to ensure

that contact is even at all points; once all the screws have been inserted,
repeat the sequence with a final tightening.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

30-1
Chapter 30 Communication ports
Contents Page
General notes 30-2
Necessary steps 30-2
MSP serial port 30-3
ASP serial port 30-4
ASP-15L serial port 30-5
ASP-9 serial port 30-6
ASP-8 serial port 30-6
LPT parallel port 30-7
Ethernet port 30-8
Interbus-S port 30-9
Profibus-DP port 30-10
CAN port 30-10
RS485 serial port 30-11
PC/VT serial port 30-11
PC <-> VT connection 30-12

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 30
30-2 Communication ports
All VTs communicate with other devices by means of serial and/or parallel
communication ports. We list on the following page the individual ports
with the respective type of communication and the function of the connec-
tion pins.
General notes Serial communication is particularly prone to disturbances. To limit the influ-
ence of these disturbances it is necessary to use good quality shielded cables.
The table immediately below lists the characteristics of the cable we recom-
mend for serial connection.
Specifications of serial connection cable

Direct current resistance Max. 151 Ohm/Km
Capacity coupling Max. 29pF/m
Shielding > 80% or total
Particular care should be taken in the choice and lay-out of cables,

specially with regard to the VT <-> Device connection serial cable.
Always:
Find the shortest route
Lay disturbed cables separately
Disconnect the power supply before connecting or disconnecting

the communication cables so as to avoid possible damage to the
VT and/or the connected device.
Necessary To have the communication ports (MSP, ASP, ASP-9 or ASP-8) function-
steps ing properly, certain pins on the VT side need to be jump-connected. The
ASP-15L port requires no jumpers.Which pins need to be connected
depends on which communication standard is to be used (RS232, RS422,
RS485 or C.L.TTY-20mA).
Table 30.1: Jumpers to be effected inside the communication cable.

Pin number Communication standard
Signal
MSP ASP-8 ASP-9 ASP RS232 RS422 RS485 C.L.a C.L.p
RTS OUT 4 4 7 10
2 2 2 2 2
CTS IN 5 5 8 11
IKR OUT (C.L.) 15
1 1 1
RX+ IN (C.L.) 18
Signal GND 7
RX- IN (C.L.) 25 1 1 1 1
TX- OUT (C.L.) 11

Notes:
1 - Jumpers always to be effected.
2 - Jumpers to be effected only if the corresponding signals are not handled by the device connected to the VT.
C.L.a - Current Loop (Activ VT), C.L.p - Current Loop (Passive VT)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

30-3
MSP serial The MSP (Multi Serial Port) is present on all VTs and is used to connect other
port devices including the PC used to transfer the project. It consists of a connector
(D-Sub 25 pin female) and can communicate using RS232, RS422, RS485 and
C.L. (TTY-20mA).
MSP
Multi Serial Port
25 pin female
Pin Signal Notes

1 N.C. Not connected
2 Tx OUT RS232
3 Rx IN RS232
4 RTS OUT RS232
5 CTS IN RS232
7 Signal GND Internal reference 0Volt
9 Tx +OUT C.L. (TTY-20mA) Current loop
10 Tx/Rx -IN/OUT RS485
11 Tx -OUT C.L. (TTY-20mA) Current loop
12 Tx -OUT RS422
13 Rx +IN RS422
14 IKT OUT C.L. (TTY-20mA) Current loop
15 IKR OUT C.L. (TTY-20mA) Current loop
16 +5Vdc (150mA Max.) Reserved for Esa
18 Rx +IN C.L. (TTY-20mA) Current loop
22 Tx/Rx +IN/OUT RS485
23 Tx +OUT RS422
24 Rx -IN RS422
25 Rx -IN C.L. (TTY-20mA) Current loop
Pin 16 does not provide for commuting any kind of load (coils etc.);
an input disturbance at Pin 16 can cause the VT and therefore also
the industrial process itself to malfunction.
Strong input disturbances at Pin 16 could damage the VT.
Before connecting in RS422/485, check the polarities. With some

devices the Tx+/Rx+ and Tx-/Rx- signals or the polarities are
inverted.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 30
ASP serial The ASP (Auxiliary Serial Port) consists of a D-Sub 15 pin female connec-
port tor and can communicate using RS232 and RS485.
ASP
Auxiliary Serial Port
15 pin female
Pin Signal Notes

1 DCD IN RS232
2 RX IN RS232
3 TX OUT RS232
4 DTR OUT RS232
9 DSR IN RS232
10 RTS OUT RS232
11 CTS IN RS232
12 RI IN RS232
Pin 13 does not provide for commuting any kind of load (coils
etc.); an input disturbance at Pin 13 can cause the VT and there-
fore also the industrial process itself to malfunction.
Before connecting in RS422/485, check the polarities. With some

inverted.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

30-5
ASP-15L serial The ASP (Auxiliary Serial Port) consists of a D-Sub 15 pin female connec-
port tor and can communicate using RS232 and RS485. Unlike the ASP it does
not carry all signals.
ASP-15L
15 pin female
Pin Signal Notes

2 RX IN RS232
3 TX OUT RS232
Before connecting in RS485, check the polarities. With some

inverted.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 30
ASP-9 serial The ASP-9 serial port (Auxiliary Serial Port) consists of a D-Sub 9 pin
port male connector and can communicate using RS232.
ASP-9
9 pin male
Pin Signal Notes

1 DCD IN --
2 RX IN --
3 TX OUT --
4 DTR OUT --
6 DSR IN --
7 RTS OUT --
8 CTS IN --
9 RI IN --
ASP-8 serial The ASP-8 (Auxiliary Serial Port) consists of a Minidin 8 pin female con-
port nector and can communicate using RS232.
ASP
8 pin female
Pin Signal Notes

1 RX IN --
2 TX OUT --
4 RTS OUT --
5 CTS IN --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

30-7
LPT parallel The LPT parallel port consists of a D-Sub 25 pin female connector. It is
port used to connect directly with the printer.
LPT
25 pin female
Pin Signal Notes

1 Strobe --
2 PRN Data 0 --
3 PRN Data 1 --
4 PRN Data 2 --
5 PRN Data 3 --
6 PRN Data 4 --
7 PRN Data 5 --
8 PRN Data 6 --
9 PRN Data 7 --
11 PRN Busy --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 30
Ethernet port The Ethernet port comprises an RJ45 8 pin female connector and is dedi-
cated to creating network links with other terminals, with PCs and any other
device that supports this standard.
Ethernet
RJ45
8 pin female
Pin Signal Notes

1 TX+ --
2 TX- --
3 RX+ --
4 -- Reclosing with pin 5 and 75 ohm termination
6 RX- --
The Ethernet connector has two diagnostic LEDs on the communication

and on the network connection. The following table gives the respective
meanings.
ACT Two-color LED, green/yel- LINK Green LED for showing

low for showing network activity network connection
Led
Meaning
ACT LINK
Cable disconnected, interrupted or
Off Off
participants off
Do not care On Network connection
Yellow On Data exchange at 10Mbit
Green On Data exchange at 100Mbit
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

30-9
Interbus-S The NETWORK1 communication port consists of a 9-pin female D-Sub

port connector.
NETWORK1
9 pin female
OUT
Pin Signal Notes

1 DO2 --
2 DI2 --
3 GND Internal reference 0Volt
5 +5V Reserved for Esa
6 /DO2 --
7 /DI2 --
9 RBST --
The NETWORK2 communication port consists of a 9-pin male D-Sub con-

nector.
NETWORK2
9 pin male
IN
Pin Signal Notes

1 DO1 --
2 DI1 --
3 GND Internal reference 0Volt
6 /DO1 --
7 /DI1 --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 30
Profibus-DP The communication port consists of a 9-pin female D-Sub connector.

port
9 pin female
Pin Signal Notes

1 Shield --
3 TxRx485+ Data B --
4 Repeater-Control-signal RTS --
6 P5V Reserved for Esa
8 TxRx485- Data A --
CAN port The communication port consists of a 5 pin female terminal block (optoiso-
lated interface).
CAN
5 pin female
Pin Signal Notes

1 V- --
2 CAN - --
3 Shield --
4 CAN + --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

30-11
RS485 serial The communication port consists of a 9-pin male D-Sub connector.
port
9 pin male
Pin Signal Notes

PC/VT serial The communication port consists of a 9-pin male D-Sub connector for con-
port necting a PC or VT in RS232.
PC/VT
9 pin male
Pin Signal Notes

2 RX IN --
3 TX OUT --
4 DTR OUT --
7 RTS OUT --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 30
PC <-> VT To transfer the communication firmware, the communication driver and the
connection project the VT must be connected to the PC (see Software Manual) and can
be done using either Serial or Modem.
RS232
Modem
The cable required to make the connection is illustrated below.
PC side VT side
9 pin female CVCOM11102 25 pin male
TxD 3 3 RxD
RxD 2 2 TxD
GND 5 7 GND
25
RTS 7 4 RTS
CTS 8 5 CTS
DSR 6 15
DTR 4 18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

30-13
The cable in the above figure, together with the relevant adapters, can be
used for all serial port connections of the VT. Below we list the adapters
and the combinations necessary for the various connections.
CVCOM25F9M CVAD25M9M CVCOM25F8M
CVCOM25F9M CVAD25M9M
PC side MODEM side

25 to 9 pins 25 to 9 pins
CVAD259 CVAD2515
CVCOM25F8M
CVAD259 CVAD2515
VT side VT side VT side

25 to 9 pins 25 to 15 pins 25 to 8 pins
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 30
The table shows how to combine adaptors and cables connection to the var-
ious ports.
Table 30.2: Combination of serial transfer + adapters

Serial Cable Adaptor
CVCOM CVCOM CVCOM CVCOM CVAD CVAD
MODEM PC VT
11102 25M9M 25F9M 25F8M 259 2515
-- 9 pins MSP -- -- -- -- --
-- 9 pins ASP -- -- -- --
-- 9 pins ASP-15L -- -- -- --
-- 9 pins ASP-9 -- -- -- --
-- 9 pins ASP-8 -- -- -- --
-- 25 pins MSP -- -- -- --
-- 25 pins ASP -- -- --
-- 25 pins ASP-15L -- -- --
-- 25 pins ASP-9 -- -- --
-- 25 pins ASP-8 -- -- --
25 pins -- MSP -- -- -- --
25 pins -- ASP -- -- --
25 pins -- ASP-15L -- -- -- -- -- --
25 pins -- ASP-9 -- -- --
25 pins -- ASP-8 -- -- -- -- -- --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

31-1
Chapter 31 Settings for the Modem
Contents Page
AT commands to be sent 31-2
Sending commands 31-3

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 31
31-2 Settings for the Modem
Before proceeding to transfer via Modem it has to be set up for reception,

that is, such that on receiving the call the Modem automatically responds
and goes into data reception mode.
Telephone
line
AT commands Modems need a series of commands, some of which can be used to set the
to be sent Modem. The table below lists the commands (supported by the majority of
modems) necessary for setting the Modem as the VTs require. The com-
mand also comprises the parameter required.
Table 31.1: AT commands
Command Effect
The modem ignores the DTR signal and considers it always

AT&D0
activated.
AT&H0
or Disables the RTS/CTS flow check.
AT&K0
AT&R1 The modem ignores the RTS and considers it always active.
ATS0=3 Let it ring 3 times before responding.
Set the volume of the modem, where n can have a value from
ATLn
1 to 3 (1=Min - 3=Max).
AT&W0 Save the modem configuration.
AT&F Reload the factory-made settings (default).
Should the commands not be accepted by the modem being used

for the transfer, consult the producers manual for a complete list
of valid commands.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

31-3
Sending To send the commands connect the modem to the serial port of the PC
commands using a standard serial cable.
RS232
Once the connection and access are established the modem runs the Hyper-
Terminal program (supplied with the PCs operating system) by clicking on
Start > Programs > Accessories > Communications > HyperTerminal
Insert the name to be

given to the
connection.
Click on the OK.
Set the COM where

the Modem is
connected (e.g.
COM1).
Click on the OK.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 31
31-4 Settings for the Modem
Set as in fig.
Click on the OK.
The main mask appears.
Check that there is a

connection between
PC and Modem.
Digit the ATH

command and confirm
with the Enter key of
the PC.
If the message OK
appears it means the
connection is active.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

31-5
Using the same

criterion, digit all the
commands necessary
for setting the modem
(see Page 31-2 -> AT
commands to be sent).
If the modem is switched off the settings are lost. If they need to be
kept, the settings can be saved using the appropriate command.
If required, you can

digit AT&W0 and
confirm using the PCs
Enter key.
The modem is ready to be connected to the VT.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

32-1
Chapter 32 Connection cable for H Series terminals
Contents Page
Standard series connection cable 32-2
Standard series connections without VTHCB 32-3
Standard series connections with VTHCB 32-6
CAN series connection cable 32-7
CAN series connections 32-7
Lay-out of button functions 32-8

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 32
32-2 Connection cable for H Series terminals
Terminals belonging to H Series (Hand Held) are supplied with a 10-meter

protected cable of 25x0.25 mm2 (AWG24), already cabled.
Under no circumstances should you modify the length of the con-

nection cable, as this could lead to malfunctioning.
Standard Below are the connections.

series
connection Command and/or sig-
Cable from VT Signals
cable nal unit
Yellow-Green
Red +24VDC Power supply
Black 0VDC
Pink TX RS232 OUT - MSP
White RX RS232 IN - MSP
Blue RTS RS232 OUT - MSP
Green CTS RS232 IN - MSP
Serial communication
Yellow Signal GND
line
White-Grey TX/RX RS485 -IN/OUT - MSP
Yellow-White TX/RX RS485 +IN/OUT - MSP
Blue-Brown TX RS232 OUT - ASP
White-Red RX RS232 IN - ASP
White-Black NC1
Brown-Pink NC2 System shut-down but-
White-Blue NC3 ton
Brown-Grey NC4
Brown-Red C1
Yellow-Brown NC1
Enabling button
Violet C2
Green-Brown NO2
Green-White NO
Black button
White-Pink C
Red-Blue NO
Luminous green button
Grey-Pink C
Brown -
Bulb
Grey +
In order to simplify the connection with the other devices you should use
the VTHCB board (optional). This interface transforms the signals from the
terminal serial line into the ESA standard (MSP, ASP-15L), allowing to use
standard connection cables (see Chapter 40 -> Connessione del Terminale
ai Dispositivi).
To see what button does what, see Page 32-8.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

32-3
Standard Connection to the DEVICE is possible in the modalities described below.

series
connections For practical reasons, the diagrams below represent both connec-
without tions, although these are independent from each other. It is possi-
VTHCB ble to perform the connections of the only serial you intend to use.
The serial line used directly on the cable DOES NOT allow the use
of ESA standard connection cables (see Chapter 40 -> Connes-
sione del Terminale ai Dispositivi).
RS232 without RTS/CTS management:
VT DEVICE
Side Side
SHD
TX RS232 OUT - MSP RX RS232
RX RS232 IN - MSP TX RS232
COM 1
RTS RS232 OUT - MSP
CTS RS232 IN - MSP
Signal GND Signal GND
TX/RX RS485 -IN/OUT - MSP
TX/RX RS485 +IN/OUT - MSP
RX RS232 IN - ASP TX RS232
TX RS232 OUT - ASP RX RS232

COM 2
Signal GND
SHD
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 32
RS232 connection with RTS/CTS management:
VT DEVICE
Side Side
SHD
TX RS232 OUT - MSP RX RS232
RX RS232 IN - MSP TX RS232
COM 1
RTS RS232 OUT - MSP CTS
CTS RS232 IN - MSP RTS
TX/RX RS485 +IN/OUT - MSP
COM 2
Signal GND
SHD
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

32-5
RS485 connection:
VT DEVICE
Side Side
SHD
TX RS232 OUT - MSP
RX RS232 IN - MSP
RTS RS232 OUT - MSP
COM 1
CTS RS232 IN - MSP
TX/RX RS485 -IN/OUT - MSP TX/RX RS485 -
TX/RX RS485 +IN/OUT - MSP TX/RX RS485 +
COM 2
Signal GND
SHD
Always insert a 220 Ohm 1/4W resistance when the connection

between VT and the device is point-to-point, or when the VT is
inserted as the first or the last component in a network (see also Chap-
ter 34 -> Collegamento in rete).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 32
It is possible to connect with the PC to transfer the project, as follows.
VT Side
25 pin female
TX RS232 OUT - MSP
RX RS232 IN - MSP
2 TxD
RTS RS232 OUT - MSP 3 RxD
7 GND
CTS RS232 IN - MSP
Signal GND

7 GND
TX/RX RS485 +IN/OUT - MSP 3 RxD
2 TxD
RX RS232 IN - ASP
TX RS232 OUT - ASP
The use of a female 25-pole connector allows to use a standard

CVCOM11102 cable for the transfer (see also Chapter 30 -> Colle-
gamento PC <-> VT).
Standard For the connection of board VTHCB, please refer to its respective chapter
series (seeChapter 33 -> Accessori per terminali video).
connections
with VTHCB
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

32-7
CAN series Below are the connections.

connection
cable Command and/or sig-
Cable from VT Signals
nal unit
Yellow-Green
Red +24VDC Power supply
Black 0VDC
Pink TX RS232 OUT
Serial communication
White RX RS232 IN
line
Yellow Signal GND
Blue CAN-
Green V- CAN communication
White-Grey Shield line
Yellow-White CAN+
White-Black NC1
Brown-Pink NC2 System shut-down but-
White-Blue NC3 ton
Brown-Grey NC4
Brown-Red C1
Yellow-Brown NC1
Enabling button
Violet C2
Green-Brown NO2
Green-White NO
Black button
White-Pink C
Red-Blue NO
Luminous green button
Grey-Pink C
Brown -
Bulb
Grey +
The CAN series integrates the serial line termination resistances

(typical 120 Ohm). The terminal is always supplied with a termi-
nated CAN line.
To see which button does what, see Page 32-8.
CAN series The CAN terminal is not expected to be used with the accessory board
connections VTHCB, which is why connections must be carried out directly on the
cable.
For the connection diagram, see Chapter 34 -> CAN Collegamento.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 32
It is possible to connect with the PC to transfer the project, as follows.
VT Side
25 pin female
TX RS232 OUT - MSP 2 TxD

3 RxD
RX RS232 IN - MSP 7 GND
Signal GND
The use of a female 25-pole connector allows to use a standard

CVCOM11102 cable for the transfer (see also Chapter 30 -> Colle-
gamento PC <-> VT).
Lay-out of System shut-down button

button
functions NC1 NC3 NC1 NC3
Pushing
button
NC2 NC4 NC2 NC4
Enabling button
NC1 NC1
NC1
Pushing C1 C1
C1
button NO2 NO2

NO2
C2 C2
C2
NC1 NC1
Releasing C1 C1
button NO2 NO2
C2 C2

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

32-9

safety.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-1
Chapter 33 Video terminal accessories
Contents Page
1/2AA Battery 33-4
Cell battery 33-4
Flash module 33-5
Fixing hook for Hand Held 33-8
Interface for connecting Hand Held with MSP/ASP-15L 33-9
Memory card 33-13
Memory module 33-18
Integrated Interbus-S module 33-19
Integrated Profibus-DP module 33-21
Protfilm4/6/6H/10/12 33-22
RS485 Serial module 33-21
Interbus-S and Profibus-DP card 33-27
Connection card for PC-NET 33-34
Adapter for external CAN network 33-37
20 key serial keyboard 33-42
Blank keyboard 33-46

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
33-2 Video terminal accessories
The video terminals are made to take a series of accessories that increase
their capacity and/or functionality. This chapter shows how these accesso-
ries relate to the various products. The table below shows which terminals
will take which accessories.
Table 33.1: Accessories connectable to VT terminals (Part 1 of 2)

ACCESSORIES TERMINALS SUPPORTING THE ACCESSORY
Lithium battery 3,6V 1/2AA VT170W, VT190W
Lithium button cell battery 3V

VT300W, VT310W, VT320W, VT330W, VT555W, VT56xW, VT585W
CR2032
Flash module 04 VT300W2, VT310W2, VT320W2, VT330W3-D, VT56xW2-C, VT585W3-D
Flash module 08 VT330W2-D, VT575W2, VT580W2, VT585W2-D, VT585WB2, VT595W2
Fixing hook for Hand Held VT505H, VT525H
Interface for connecting Hand Held

VT505H, VT525H
with MSP/ASP-15L
Memory Card 4 Mbytes VT300W2, VT310W2, VT320W2, VT330W3-B, VT56xW2-A, VT585W3-B
Memory Card 8 Mbytes VT330W2-B, VT575W2, VT580W2, VT585W2-B, VT585WB2, VT595W2
Memory module 512Kbytes VT170W1, VT190W1
Integrated Interbus-S module VT170W, VT190W
Integrated Profibus-DP module VT170W, VT190W
RS485 serial module VT170W, VT190W
Protfilm4 VT155W, VT185W
Protfilm6 VT505W, VT515W, VT525W, VT555W, VT56xW, VT575W, VT580W
Protfilm6H VT505H, VT525H
Protfilm10 VT585W, VT585WB
Protfilm12 VT585W
VT505, VT60, VT150W5, VT160W, VT170W, VT190W, VT300W4-5, VT310W4, VT320W4, VT330W4, VT155W5,
Interbus-S module
VT185W5, VT505W5, VT515W5, VT525W5, VT555W5, VT56xW, VT575W, VT580W, VT585W4, VT585WB, VT595W
Profibus-DP module
VT505, VT60, VT150W5, VT160W, VT170W, VT190W, VT300W5, VT310W, VT320W, VT330W, VT155W5, VT185W5,
Connection card for PC-NET
VT505W5, VT525W5, VT515W5, VT555W5, VT56xW, VT575W, VT580W, VT585W, VT585WB, VT595W
Adapter for external CAN network
Notes:
1 - Already present on purchase A - For terminals up to Rev. 3
2 - To be used as backup B - For terminals up to Rev. 4
3 - To be used as expansion C - For terminals from Rev. 4
4 - Can be fixed to back cover D - For terminals from Rev. 5
5 - Not applicable in the case of CAN series terminals
-- : not connectable
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-3
Table 33.1: Accessories connectable to VT terminals (Part 2 of 2)

ACCESSORIES TERMINALS SUPPORTING THE ACCESSORY
Blank keyboard VT150W, VT300W, VT310W, VT320W
Serial keyboard with 20 keys + LEDs VT150W, VT300W, VT310W, VT320W
Notes:
1 - Already present on purchase A - For terminals up to Rev. 3
2 - To be used as backup B - For terminals up to Rev. 4
3 - To be used as expansion C - For terminals from Rev. 4
4 - Can be fixed to back cover D - For terminals from Rev. 5
5 - Not applicable in the case of CAN series terminals
-- : not connectable
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
1/2AA Battery The function of the battery is both to maintain the contents of the RAM
(work recipes) and to keep the internal clock going when there is no power
supply.
Battery to be used
Lithium 3.6V AA
The battery should be replaced about every 12 months.
The battery needs to be changed either when the Battery LED (on the VT
keyboard) comes on or when indicated by the Chapter 37 -> Status
area for the terminal. Failure to change the battery will lead to the con-
tents of the data memory being lost.
The battery must be substituted with the VT power off. At this point a
high capacity condenser will momentarily preserve the RAM memory
information (information is typically retained for 24 hours).
Discarded batteries should be placed in appropriate containers.
Procedure for inserting or substituting the battery:
Check that the power supply is not connected.

Take off the hatch covering the battery compartment of the VT (see
Chapter 7 -> Rear view and/or Chapter 8 -> Rear view).
Pull off the black plastic safety-cover that snaps over the battery com-
partment.
Insert the new battery checking that the polarities are correct.
Push the safety-cover back on till it snaps into place.
Replace the hatch covering the battery compartment of the VT (see
Chapter 7 -> Rear view and/or Chapter 8 -> Rear view).
Cell battery The function of the battery is both to maintain the contents of the RAM
(work recipes) and to keep the internal clock going when there is no power
supply.
Battery to be used
Lithium 3V cell battery

CR2032
The battery should be replaced about every 12 months.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-5
The battery needs to be changed either when the Battery LED (on the VT
keyboard) comes on or when indicated by the Chapter 37 -> Status
area for the terminal. Failure to change the battery will lead to the con-
tents of the data memory being lost.
In the case of products with a Touch Screen, the running down

and/or absence of the battery is not indicated on the screen.
The battery must be substituted with the VT power off. At this point a
high capacity condenser will momentarily preserve the RAM memory
information (information is typically retained for 24 hours).
Discarded batteries should be placed in appropriate containers.
Procedure for inserting or substituting the battery:

Take off the hatch covering the battery compartment of the VT.
Insert the new battery checking that the polarities are correct.
Replace the hatch covering the battery compartment of the VT.
Flash module
ESA
For more information regarding functions and technical details see Page
33-13 -> Memory card.
Inserting the flash module into the VT:
Procedure for inserting the card:

Remove the back cover.
Locate the following element.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
The position and direction on the printed circuit board may be

different depending on which VT model is used.
Insert the spacers (A) in the holes (B) taking care which way round they
are put; then insert the flash module into the terminal.
ESA
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-7
Replace the back cover of the VT

Reconnect the VT to the power supply.
Procedure for removing the flash module:
Check that the VT power supply is disconnected.

ESA
To extract the connector (A), pull lightly, then pull on the corners, one
by one, and at the same time press down on tyhe head of the spacer (B).
ESA
A B
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33

Use of Flash module:
For information regarding the operation of the card, see Page 33-16 ->
Using the Memory Card:.
Fixing hook
for Hand Held
This is an accessory for fixing VTs that cant be embedded.
Do not alter the original form of the mounting hook or the tilt
adjustment wedge.
Fixing the device:
Various ways of fixing the device are possible. For details see Chapter 29
-> Fixing using external support.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-9
Interface for
connecting
Hand Held
with
MSP/ASP-15L
VTHCB
The table below lists the principal technical characteristics of the product
under discussion.
Connector block
Number of connection points (X1/X2) 30/14
Section of connectable wire 0,05-1,5 mmq (30-16AWG)
Stripped length of connectable wire 5-6 mm
Technical data
Power supply 24Vdc (18..32Vcc)
Power absorbed at 24Vdc 0,5W
Protection level --
Humidity (non-condensing) 85%
Weight 250gr
Dimensions
The above-mentioned board enables a VTxxxH to be connected to other

devices using standard ESA cables (see Chapter 40 -> Connection
cables). The board has a 25-pin female D-Sub MSP connector (for details
see Chapter 30 -> MSP serial port) and a 15-pin female D-Sub ASP-15L
connector (for details see Chapter 30 -> ASP-15L serial port).
The ASP-15L port does not work when connected to a VT505H

and is limited to RS232 when connected to a VT525H.
See Chapter 2 -> Power Supply for connecting the power supply.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Dimensions:
HCB
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-11
Securing the DIN rail mounting plate:
DIN EN 50022
A
B
DIN EN 50035
A
B
DIN EN 50045
A
B
Hook the upper part of the plate onto the DIN rail.
Press the device in the direction indicated. (Arrow A)
To make it easier to hook on, pull the spring-clip in the direction indi-
cated. (Arrow B)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Connection cable :
The terminal is provided with a 25x0.25mmq (AWG24) shielded cable

already attached to be connected to terminal block X1 (strip back cable
5-6mm).
Connection Connection
VT <-> VTHCB VTHCB <-> Electrical panel
Connector Connector Internal
Command and/or signal unit Cable from VT
block X1 block X2 switchboard
Yellow-Green 19
Red 1
Black 16
Pink 13
Other signals relating to opera- White 28
tion of board Blue 29
--
Green 30
Yellow 17
White-Grey 14
Yellow-White 15
Blue-Brown 5
VT525H only
White-Red 20
NC1 White-Black 6 7 See electrical
System shut-down NC2 Brown-Pink 21 14 lay-out for end user
button NC3 White-Blue 22 13
NC4 Brown-Grey 7 6
C1 Brown-Red 23 12
NC1 Yellow-Brown 8 5
Enabling button
C2 Violet 24 11
NO2 Green-Brown 9 4
NO Green-White 11 2
Black button
C White-Pink 10 3
Luminous green NO Red-Blue 26 9
button C Grey-Pink 25 10
- Brown 27 8
Bulb
+ Grey 12 1
Never alter the length of the connection cable as this may cause
malfunctioning.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-13
Example of implementation of VTHCB board.
Internal
swirtchboard
circuit
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10
VTHCB
Memory card
This is a removable device in which you can store the information con-
tained in the VT terminal.
The Memory Card (Flash EPROM type) can be used:
as a backup for the project and firmware

to load one or more terminals without using a PC
to send the end-user updates (without VTWIN)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
The types of information that can be stored on the Memory Card are:
Firmware
Project
Recipes
Start-up language
Password
The following table lists the principal technical characteristics of the prod-
uct in question.
Technical data
Memory 4Mb or 8Mb
Inserting the memory card into the VT:
Procedure for inserting the card:

Insert the memory card in its housing, checking that it is the right way
round.
To insert, following the

Front view direction of the arrow till Rear View
the card fits securely into
its slot.
Contacts for
electrical con-
nection
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-15
Once the memory card fits in the groove, press lightly as shown in the
figure till you feel it click into place.

Procedure for removing the memory card:
Check that the VT power supply is disconnected.

Press lightly on the fixing tab of the memory card (see figure below) in
the direction of the arrow.
Once the memory card is unhooked (see figure) remove it following the
direction of the arrow.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Replace the back cover on the VT

Reconnect the power supply to the VT
To operate the memory card you need to be in an appropriate page contain-

ing the menu with the corresponding commands (for how to enter the menu
page see the chapter for the product concerned).
The graphic form of the page, the contents of the menus and their meaning
depend on the type of terminal being used.
The functions listed below do NOT require confirmation; press

the key and the function will be executed (also in the case of
Erase).
The following are the functions available with VT300W, VT310W,

VT320W, VT56xW, VT585W:
Erase
Restore
Backup
Exit
Erase:
Makes it possible to erase the Memory Card completely with

permanent loss of data on it.
Restore:
Makes it possible to transfer the contents of the Memory Card

to the VT terminal.
Backup:
Makes it possible to transfer data from the memory of the VT

terminal to the Memory Card.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-17
Exit:
Makes it possible to quit the menu page and return to the pre-
vious page.
It is not possible to partially cancel or write the Memory

Card; consequently single items of information (only firm-
ware, only recipes, etc.) can neither be added or deleted.
The following are the functions available with VT330W, VT575W,

VT580W, VT585WB and VT595W:
Backup ALL
Backup FW/PRJ
Backup RECIPES
Backup ALARMS
Restore ALL
Restore FW/PRJ
Restore RECIPES
Restore ALARMS
Exit
Backup ALL:
This function allows you to clear the memory card of its data,
all its contents being definitively lost, and then to transfer to it
all the data contained in VT memory.
Backup FW/PRJ:
This function allows you to clear the relevant section of the mem-
ory card of its data, all its contents being definitively lost, and then
to transfer to it the project (Start-up language and Password
included) and the firmware contained in VT memory.
Backup RECIPES:
This function allows you to clear the relevant section of the

memory card of its data, all its contents being definitively lost,
and then to transfer to it the recipes contained in VT memory.
Backup ALARMS:
This function allows you to clear the relevant section of the

memory card of its data, all its contents being definitively lost,
and then to transfer to it the alarm buffer contained in VT
memory.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Restore ALL:
This function allows you to transfer the complete content of

the memory card to the VT.
Restore FW/PRJ:
This function allows you to transfer the project and the firm-
ware contained in the memory card into the VT.
Restore RECIPES:
This function allows you to transfer the recipes contained in

the memory card into the VT.
Restore ALARMS:
This function allows you to transfer the alarm buffers con-

tained in the memory card into the VT.
Exit:
Makes it possible to quit the menu page and return to the pre-
vious page.
Memory
module
This is a removable device capable of saving the VTs firmware and its
project.
Although the device is removable, there must be a Memory mod-

ule in the terminal for it to function.
uct under discussion.
Technical data
Memory 512Kbytes
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-19
Substituting the Memory module:
Check that the VT power supply is not connected.

Locate the already existing module.
Remove this module with great care.
Insert the new module.
Integrated
Interbus-S
module
NETWORK2
D-SUB
NETWORK1
D-SUB
The integrated module shown above allows you to connect a number of ter-
minals in an Interbus-S network. For more details concerning the network
connection of the terminals see Chapter 34 -> Network connection.
The NETWORK1 communication port consists of a 9-pin female D-Sub

connector (see Chapter 30 -> Interbus-S port).

nector (see Chapter 30 -> Interbus-S port).
Inserting the module in the VT:
Check that the power supply of the VT is not connected.

Locate the elements indicated by the arrow.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Insert the spacers (A) into the holes (B), checking the they are the right
way round; now insert the module into the terminal.
A
B
B A
D-SUB D-SUB
NETWORK1 NETWORK2
Set the network address using the appropriate Dip-Switch (not present on
this module).
Reconnect the power supply of the VT.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-21
The figures above relate to VT170W; basically the procedure for

insertion is the same for all the products in which this type of
module can be inserted (see Page 33-2).
Integrated
Profibus-DP
module
ON
1 2 3 4 5 6 7 8
NETWORK1
D-SUB
The integrated module shown above enables a number of terminals to be
connected in a Profibus-DP network. (For further details on how terminals
are connected in the network see Chapter 34 -> Network connection.)
The NETWORK1 communication port consists of a 9-pin female D-Sub
connector (see Chapter 30 -> Profibus-DP port).
See Page 33-19 for how to insert the module in the VT.
RS485 Serial
module
NETWORK1
D-SUB
The integrated module shown above allows many terminals to be connected

in an ESA-Net network. (For further details regarding the connection of ter-
minals in the network see Chapter 34 -> Network connection.)

nector (see Chapter 30 -> RS485 serial port).
See Page 33-19 for how to insert the module into the VT.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Protfilm4/6/6H/
10/12
201.0
160.0
149.0
94.0
PROTFILM4 PROTFILM6
250.0
201.0
139.0
PROTFILM6H
187.0
PROTFILM10
279.0
206.0
PROTFILM12
This is a transparent protective film to be applied to the front of the touch

screen terminal to protect it from wear on the part of external agents (see
Chapter 41 -> Resistance to chemical substances).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-23
Applying the film:
How to apply the adhesive film:
Remove any trace of dirt or grease from the terminal using denaturized
ethyl alcohol
Dry the area thoroughly
Locate the adhesive part of the transparent film
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Position the film near the upper edge and smooth it down delicately
VT155/185W VT505/515/525/555/56xW
VT575W VT580W
VT585W VT585WB
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10
VT595W VT505/525H
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-25
Pass a soft cloth firmly over the edges to ensure adhesion
VT155/185W VT505/515/525/555/56xW
VT575W VT580W
VT585W VT585WB
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10
VT595W VT505/525H
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
How to remove the adhesive film:
To remove the film, pull upwards using the tab
VT155/185W VT505/515/525/555/56xW
VT575W VT580W
VT585W VT585WB
F1 F6
F2 F7
F3 F8
F4 F9
F5 F10
VT595W VT505/525H
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-27
Interbus-S and
Profibus-DP
card
The casing is the same both for the Interbus-S and the Profi-
bus-DP networks; a label is attached to indicate which network is
contained.
under discussion.
Technical data
Protection level --
Weight 800gr
Dimensions
The device incorporates the Interbus-S and Profibus-DP network cards (see
Page 33-19 and Page 33-21 for information); it also contains a power sup-
ply card with a communication port composed of a 9 pin male D-Sub con-
nector for connecting a PC or VT in RS232 (see Chapter 30 -> PC/VT
serial port).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
The external power supply for this card can also come via a 4-pin connector
or a jack.
The connection to the VT uses the following cables.
DEVICE VT Side
Side MSP
9 pin female 25 pin male
TxD 3 3 RxD
RxD 2 2 TxD
GND 5 7 GND
25
4 RTS
5 CTS
15
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-29
DEVICE VT Side
Side ASP-9
9 pin female 9 pin female
TxD 3 2 RxD
RxD 2 3 TxD
GND 5 5 GND
7 RTS
8 CTS
Max. 15 m.
DEVICE VT Side
Side ASP
9 pin female 15 pin male
TxD 3 2 RxD
RxD 2 3 TxD
GND 5 7 GND
10 RTS
11 CTS
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
The connection to the PC uses the following cables.
DEVICE PC
Side Side
TxD 3 2 RxD
RxD 2 3 TxD
GND 5 5 GND
7 RTS
8 CTS
6 DSR
4 DTR
Max. 15 m.
DEVICE PC
Side Side
TxD 3 3 RxD
RxD 2 2 TxD
GND 5 5 GND
7 RTS
8 CTS
6 DSR
20 DTR
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-31
Dimensions:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
The device is supplied with a special molded plate for attaching to the DIN
rail. The following figure shows how to fit the plate to the device.
Holes (not central)
Spring clip
Locate the two fixing holes.

Position the device such that the holes are decentered towards the top
Secure the mounting plate with the screws supplied keeping the
spring-clip down.
Attaching the device to the DIN rail:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-33
Once the mounting plate has been attached,

cated. (Arrow B)
Fixing the device to the back cover:

Attach the device as illustrated above using the appropriate screws sup-
plied and making sure the direction is correct.
Reconnect the VT power supply.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
The above illustrations refer to VT320W; the procedure is basi-

cally the same for all those products that can be fixed to the back
cover (see Page 33-2).
Connection
card for
PC-NET
under discussion.
Technical data
Protection level --
Weight 800gr
User memory
Project [Bytes] 16K
Definible groups 255*
Objects per group 255*
Simultaneously active groups 10
Dimensions
The adapter indicated above makes it possible to connect a device to a PC

or several VTs to a PC using the ESANET network. The adapter is
equipped with a D-Sub 25 pin female MSP connector (for details see
Chapter 30 -> MSP serial port) and a D-Sub 9 pin male PC/VT connector
(for details see Page 33-27).The external power supply for this card can
also come via a 4-pin connector or a jack.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-35
The connection to the PC uses the following cables.
DEVICE PC
Side Side
TxD 3 2 RxD
RxD 2 3 TxD
GND 5 5 GND
7 RTS
8 CTS
6 DSR
4 DTR
Max. 15 m.
DEVICE PC
Side Side
TxD 3 3 RxD
RxD 2 2 TxD
GND 5 5 GND
7 RTS
8 CTS
6 DSR
20 DTR
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Dimensions:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-37
Fixing the device:
Various ways of fixing the device are possible. For details see Page 33-32,
Page 33-32 and Page 33-33.
Adapter for
external CAN
network
under discussion.
Technical data
Protection level --
Weight 580gr
Dimensions
The above adapter makes it possible to connect several terminals in a CAN

network. For further details regarding the connect in network of the terminals
see Chapter 34 -> Network connection. The adapter is equipped with a Minidin
8 pin female ASP-8 connector (for details see Chapter 30 -> ASP-8 serial port)
and a disconnectable 5 pin female terminal block for connecting the CAN net-
work (optoisolated interface - see Chapter 30 -> CAN port).
The connection to the VT uses the following cables.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
DEVICE VT Side
Side MSP
8 pin male 25 pin male
TxD 2 3 RxD
RxD 1 2 TxD
GND 7 7 GND
RTS 4 25
CTS 5 4 RTS
5 CTS
5 15
8
7 4
2 MiniDin
6
1 Front 18
3
View
Max. 15 m.
Dimensions:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-39
Termination of CAN line:
The device in question integrates the termination resistances of the serial

line (typically 120 ohms) which can be inserted by means of a jumper (pre-
set on 1-2, line not terminated). To activate the termination:

Remove the cover.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
The device is supplied with a special molded plate for attaching to the DIN
rail. The following figure shows how to fit the plate to the device.
Holes (not central)
Spring clip
Locate the two fixing holes.

Position the device such that the holes are decentered towards the top
Secure the mounting plate with the screws supplied keeping the
spring-clip down.
Attaching the device to the DIN rail:
A
B
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-41
Once the mounting plate has been attached,

cated. (Arrow B)
Fixing the device to the back cover:

Attach the device as illustrated above using the appropriate screws sup-
plied and making sure the direction is correct.
Reconnect the VT power supply.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
The above illustrations refer to VT320W; the procedure is basi-

cally the same for all those products that can be fixed to the back
cover (see Page 33-2).
20 key serial
keyboard
uct in question.
Keyboard
Operational keys --
Diagnostic LEDs --
Technical data
Power supply --
Power absorbed at 24Vdc --
Weight 550gr
Dimensions
External W x H x D [mm] 148 x188 x 27
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-43
Front view:
Key Function
1 Labels for customizing F-keys
2 F-keys
Rear view:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Position Function
Point for connecting to VT by means of a shielded flat cable

A
(Max. length 300mm)
Dimensions and Cut-out:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-45
Connection with cable:
The serial keyboard accessory is connected directly to the auxiliary port

(see Chapter 5 -> Standard series rear view) of VT150W by means of a
shielded flat cable, no external power being necessary. The maximum
length of the cable is 300 mm.
The explanation of the connection method applies to all terminals with this
accessory (See Page 33-2).
Care must be exercised in making these connections: using the

accessories provided and following the wiring instructions set out
below.
A
B
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
When supplied the cable will already be fixed to the keyboard at point A,
leaving point B to be connected at the other end.
Procedure for connecting to point B:

Take off the back cover of the VT (see Chapter 5 -> Standard series
rear view).
Open the pre-cut for mounting the connector on the cover by pressing in
the metal plate and remove it (see Chapter 5 -> Standard series rear
view point B).
Replace the back cover of the VT.
Insert the cable connector into the VT (see Chapter 5 -> Standard
series rear view point B).
Secure the cable to the VT by means of the collar and screws provided.
It is essential that the metal collar pressing on the shield of the

connecting cable make direct contact with the metal cover of
the VT. If this does not happen, there could be problems due to dis-
turbances deriving from the work environment.
Reconnect the power supply to the VT.
Blank
keyboard
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-47
uct in question.
Technical data
Power supply --
Power absorbed at 24Vdc --
Weight 100gr
Dimensions
External W x H x D [mm] 148 x188
Front view:
The blank keyboard has no keys.
This accessory allows the user to fit and wire buttons. Any kind of key-pad
can be used.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 33
Dimensions and Cut-out:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

33-49
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-1
Chapter 34 Network connection
Contents Page
Profibus-DP 34-3
Profibus-DP (ESA profile): VT operation 34-4
Profibus-DP (ESA profile): Configuration software 34-4
Profibus-DP (ESA profile): Logical diagram 34-5
Profibus-DP (ESA profile): Physical diagram 34-6
Profibus-DP (Standard): VT operation 34-6
Profibus-DP (Standard): Configuration software 34-6
Profibus-DP (Standard): Logical diagram 34-7
Profibus-DP (Standard): Physical diagram 34-7
Profibus-DP: Connection 34-8
Interbus-S 34-10
Interbus-S: VT operation 34-10
Interbus-S: Configuration software 34-10
Interbus-S: Logical diagram 34-11
Interbus-S: Physical diagram 34-12
Interbus-S: Connection 34-12
ESA-Net 34-14
ESA-Net: VT operation 34-14
ESA-Net: Connecting the terminals 34-16
ESA-Net: Configuration software 34-20
ETHERNET 34-21
ETHERNET: VT operation 34-21
ETHERNET: Configuration software 34-21
ETHERNET: Connections 34-22
ETHERNET: Checking the connection 34-23
CAN 34-24
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
34-2 Network connection
Contents Page
CAN: VT functioning in CAN network 34-24
CAN: Configuration software 34-25
CAN: Connection 34-25

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-3
VT terminals can be connected, using the appropriate optional cards, inte-

grated or external, in a network with other devices. The networks available
are Profibus-DP, Interbus-S, ESA-Net, Ethernet and CAN.
Profibus-DP A VT equipped with a network card can be connected within a Profibus-DP

network as a slave (a passive station that can only transmit data after receiv-
ing a request from an active station). The PLCs and the network configura-
tor, on the other hand, are masters (active network stations able to transmit
information without receiving a request).
VT terminals have two ways of exchanging data with the network master:
one called ESA Profile and the other known as Standard Profile. In practice
the difference lies in the size of the I/O area: with ESA Profile the I/O area
is 32bytes + 32bytes and is handled by a FB (Function Block) (not available
on all devices) that has the task of allowing the VT read and write access to
all the data areas of the device; the Standard profile can use an I/O area of
up to 128bytes + 128bytes, corresponding to the maximum data area
dimensions visible to the VT.
A network can contain more than one master and more than one slave,
while there can only be one configurator.
The slave address of the VT must coincide with the network configuration.
It can be set using VTWIN if using a VT with an integrated network card,

or by means of a Dip-Switch if using a VT with a supplementary network
card.
The VT can work at a maximum speed of 12 Mbaud and it automatically

assumes the speed of the network as determined by the network master.
Table 34.1: Setting of VT network address.

ON
12345678
ON
1 2 3 4 5 6 7 8
D-SUB
Example of Dip-Switch con-

Profibus-DP supplementary card
figuration of address 11
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
Table 34.2: Meaning of the Dip-Switches

Dip-Switch Binary value Dip-Switch Binary value
1 1 5 16
2 2 6 32
3 4 7 64
4 8 8 128
Profibus-DP The slave VTs are seen generally as dedicated areas of memory in the
(ESA profile): PLCs I/O area, or alternatively in other data areas made accessible by the
VT operation configurator of the master, which are used by the PLC and VT to exchange
data. The size of the I/O area of each VT participating in the network is
defined by the user with a 4 to 16 word limit (8-32byte).
Note that the greater are the dimensions of the I/O area the faster the han-
dling of the information, though this also means a greater effort on the part
of the CPU of the PLC and thus an increase in the scanning time.
Profibus-DP There are 4 types of software that play a part in configuring the network:
(ESA profile):
Configuration VTWIN
software FB
File with extension GSD
Configuration software for network master
These types of software require parameters that coincide.
VTWIN:
The parameters that must be set in the VTWIN project of every ter-
minal connected in the network are:
Size (in words of the I/O area)

Timeout for testing the connection between the VT and PLC.
Address of terminal.
FB:
This is a program supplied by ESA to be loaded into the PLC. This

program is used to check the network parameters set and the data
exchange. It varies according to the type of PLC (make and model).
Besides the parameters which we have just seen in VTWIN, the
incoming FB requires other information related to the PLC that will
be hosting it.
The necessary user information is contained on the disk VT-PROFI-
BUS Installation SW supplied along with the Profibus-DP option.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-5
File with extension GSD (dedicated to ESA profile):
This file is supplied by ESA; it allows the configuration software of

the network master to recognize the VT.
Network master configuration software:
This software is supplied by the producer of the network master.
Profibus-DP Below is a logical diagram of the VT <-> Profibus-DP (ESA profile) con-
(ESA profile): nections. The diagram indicates how and at what level the FBs supplied by
Logical ESA interact with the system. The FB INIT takes care of the initial config-
diagram uration of the system (input and output areas, etc.), while the FB DRIVER
takes care of the data exchange between the PLC memory and the VTs, and
viceversa. The number of FB calls within the PLC must be equal to the
number of VTs connected in the system.
PLC BUS VT
PLC LOCAL SING LE CALL CYCLICAL MASTER in

DATA DATA ONLY CALL PROFIBUS-DP
MEMORY for FB AT STATR-UP
VT#1
PARAMETRIZED PARAMETRIZED
PROFIBUS-DP
FB INIT FB DRIVER
INTEG RATED
MODULE
ESA HM I ESA HMI
OR
PROFILE PROFILE
Supplied by Supplied by PROFIBUS-DP
ESA elettronica ESA elettronica MODULE
LENGTH
8-32 BYTES O UTPUT
INPUT
I/O
GSD File LENGTH
8-32 BYTES
LENGTH
8-32 BYTES INPUT
OUTPUT
VT#n
PROFIBUS-DP
FB INIT FB DRIVER
INTEG RATED
MODULE
ESA HM I ESA HMI
OR
PROFILE PROFILE
Supplied by Supplied by PROFIBUS-DP
LENGTH
8-32 BYTES O UTPUT
INPUT
I/O
GSD File LENGTH
8-32 BYTES
LENGTH
8-32 BYTES INPUT
OUTPUT
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
Profibus-DP The following figure represents the physical form of the

(ESA profile): VT <-> Profibus-DP connection.
Physical
diagram
Profibus-DP
Master
ESA module
All VTs
Profibus-DP
VT with native Profibus-DP

VT DP
VT170W and VT190W with inte-

grated Profibus-DP module
Profibus-DP The slave VTs are seen generally as dedicated areas of memory in the
(Standard): VT PLCs I/O area, or alternatively in other data areas made accessible by the
operation configurator of the master, which are used by the PLC and VT to exchange
data. The size of the I/O area of each VT participating in the network is
defined by the user with a 4 to 64 word limit (8-128byte).
Profibus-DP There are 3 types of software that play a part in configuring the network:
(Standard):
Configuration VTWIN
software File with extension GSD
VTWIN:
Size (in words of the I/O area)

Address of terminal.
File with extension GSD (dedicated to Standard profile):
This file is supplied by ESA; it allows the configuration software of

the network master to recognize the VT.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-7
Profibus-DP Below is a logical diagram of the VT <-> Profibus-DP (Standard) connec-

(Standard): tions.
Logical
diagram PLC BUS VT
PLC MASTER in
DATA PROFIBUS-DP
MEMORY
VT#1
PROFIBUS-DP
INTEGRATED
MODULE
OR
PROFIBUS-DP
MODULE
LENGTH
8-128 BYTES OUTPUT
INPUT
I/O
GSD File LENGTH
8-128 BYTES
LENGTH
8-128 BYTES INPUT
OUTPUT
VT#n
PROFIBUS-DP
INTEGRATED
MODULE
OR
PROFIBUS-DP
MODULE
LENGTH
8-128 BYTES OUTPUT
INPUT
I/O
GSD File LENGTH
8-128 BYTES
LENGTH
8-128 BYTES INPUT
OUTPUT
Profibus-DP Below is a physical diagram of the VT <-> Profibus-DP connections.

(Standard):
Physical Profibus-DP
diagram Master
ESA Module
All VTs
Profibus-DP
VT with native Profibus-DP

VT DP
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
Profibus-DP: Below is a diagram of the connections of devices in Profibus-DP network.

Connection
Master
A
B B B A
Slave
Address Address Address Address

4 5 124 125
As can be seen from the above diagram the connections for devices at either
end of the line (A) are different from the internally positioned ones (B).
Indeed, the connectors at A have inside them the termination resistances of
the line. There follow the types of connection existing within the connec-
tors.
Type A connector Type B connector

D-Sub 9 pin male D-Sub 9 pin male
TxRx+
6 P5V 3
(B)
470
1/4 W TxRx-
TxRx+
3 8
(B) (A)
220
1/4 W
TxRx-
8
(A)
470
1/4 W
5 GND
Use the materials listed in the table below when making connection cables.
Table 34.3: Cables
Maker/Distributor Type Web
Belden 3079A PROFIBUS Cable www.belden.com
Siemens Simatic Net Profibus www.siemens.com

FC6X91 830-0E11 10
1DR 22X 02R
Intercond www.intercond.com
1DR 22X 02P
For further details contact the retailer and/orvisit the appropriate WEB site.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-9
Table 34.4: Connectors.
6ES7972-0BA10-0XA0
6ES7972-0BB10-0XA0
Siemens 6ES7972-0BA40-0XA0 www.siemens.com
6ES7972-0BB40-0XA0
6GK1500-0EA00
103 648
103 658
103 663
103 649
Erni www.erni.com
103 659
104 329
104 577
104 322
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
Interbus-S A VT equipped with a network card can be connected within a network as a

slave (a passive station that can only transmit data after receiving a request
from an active station). The master communication card, generally inserted
in a PLC station, transmits and recieves information from the slaves. There
can be more than one slave connected to a single master in a network.
Interbus-S: VT The slave VTs are seen generally as dedicated areas of memory in the
operation PLCs I/O area, or alternatively in other data areas made accessible by the
configurator of the master, which are used by the PLC and VT to exchange
data. The size of the I/O area of each VT participating in the network is 4
words (8byte).
Interbus-S: There are 3 types of software that play a part in configuring the network:
Configuration
software VTWIN
FB
VTWIN:
FB:
This is a program supplied by ESA to be loaded into the PLC. This

program is used to check the network parameters set and the data
exchange. It varies according to the type of PLC (make and model).
Besides the parameters which we have just seen in VTWIN, the
incoming FB requires other information related to the PLC that will
be hosting it. This information is contained in a text file on the disk
entitled VT-INTERBUS Installation SW.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-11
Interbus-S: Below is a logical diagram of the VT <-> Interbus-S connections. The dia-
Logical gram indicates how and at what level the FBs supplied by ESA interact
diagram with the system. The FB INIT takes care of the initial configuration of the
system (input and output areas, keys area, etc.), while the FB DRIVER
takes care of the data exchange between the PLC memory and the VTs, and
viceversa. The number of FB calls within the PLC must be equal to the
number of VTs connected in the system.
PLC BUS VT
PLC LOCAL SINGLE CALL CYCLICAL MASTER in

DATA DATA ONLY CALL INTERBUS
MEMORY for FB AT STATR-UP
VT#1
INTERBUS
FB INIT FB DRIVER
INTEGRATED
MODULE
ESA HM I ESA HM I
OR
PROFILE PROFILE
Supplied by Supplied by INTERBUS
LENGTH
8 BYTES OUTPUT
INPUT
I/O
LENGTH
8 BYTES
LENGTH
8 BYTES INPUT
OUTPUT
VT#n
INTERBUS
FB INIT FB DRIVER
INTEGRATED
MODULE
ESA HM I ESA HM I
OR
PROFILE PROFILE
Supplied by Supplied by INTERBUS
LENGTH
8 BYTES OUTPUT
INPUT
I/O
LENGTH
8 BYTES
LENGTH
8 BYTES INPUT
OUTPUT
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
Interbus-S: Below is a physical diagram of the VT <-> Interbus-S connections.

Physical
diagram Interbus-S
Master
ESA Module
All VTs
Interbus-S
ESA Module
All VTs
Interbus-S
VT170W and VT190W with inte-

grated Interbus-S module
Interbus-S: Below is a diagram of the connections between the VTs and the devices in
Connection Interbus-S network.
In
Master
Out
A
B
Slave
VT#1 VT#2 VT#n-1 VT#n
Parameter n stands for the maximum number of terminals that can be con-
nected in the network, which depends on the size of the memory available
in the master device for the input and output of process data. Each VT con-
nected occupies 64 bits for the data input area and 64 bits for the process
data output; thus
I/O area of master device

n=
64 bit
Below we list the connection cables required.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-13
Connector A Connector B
D-Sub 9 pin male D-Sub 9 pin female
green
/DO2 6 6 /DO1
DO2 1 yellow
1 DO1
pink
/DI2 7 7 /DI1
DI2 2 grey 2 DI1

brown
GND 3 3 GND
+5V 5
RBST 9
Use the materials listed in the table below when making connection cables.
Table 34.5: Cables
Belden 3120A INTERBUS Cable www.belden.com
Phoenix 27 18 28 0 www.phoenixcontact.com
Table 34.6: Connectors.
27 58 47 3
Phoenix www.phoenixcontact.com
27 58 48 6
103 650
103 651
Erni 103 660 www.erni.com
103 661
104 319
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
ESA-Net All VT terminals can be connected in an ESA-Net network as Network Cli-

ents or as Network Servers (see technical characteristics of individual ter-
minals). The network Client can only ask other terminals in the network for
information (variables); while the network Server makes information (vari-
ables) available to other terminals in the network.
ESA-Net: VT To help clarify the concept of ESA-Net, we offer the data-flow diagram
operation below showing how a terminal assumes the function of client, server and
server/client.
D D D
V VP V VP V VP V
1 2 3 4
MAX. 32 Participants
8 7 6 5
V V VP V VP
D D
In the ESA-Net network the server terminal is the one that makes all or
some of the variables available to the other terminals; these variables are
called Public Variables.
The maximum length of public objects is 60 Bytes; excess lengths

will be truncated. To avoid this, we suggest more than one object
with the appropriate lengths (with a length of 120 Bytes use two objects
of 60 Bytes).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-15
The maximum number of public objects is 128, making a total of

1024 Bytes.
The client terminal is the one that uses the public variables made available
by the server terminal. The terminal that uses public variables and, in its
turn, makes others available is known as the server/client. Generally, the
client terminal has no device of any kind connected.
The example in the figure shows eight terminals connected, of which:
1 -> Server/Client -> V/VP -> Device

4 -> Client -> V
5 -> Server -> VP -> Device
7 -> Client -> V
8 -> Client -> V
The area colored green (VP) represents the public variables, the area col-
ored yellow (V) represents the variables; the device is indicated schemati-
cally in violet (D). The two central rings, one represented by a continuous
red line indicates the VTs response to a request (the dotted lined traced in
blue indicates the request for information.
A network can have more than one server, more than one client and more
than one server/clients, the total being 32 terminals.
The network participants must each have a different address; the address of
the terminal is configured using the VTWIN (see Software Manual).
A terminal can connected to the network either using the communication

standard RS485 and the MSP and ASP (default) serial ports or, alterna-
tively, using an RS485 serial module (optional) - (see Chapter 33 -> Video
terminal accessories).
To avoid any problems, the device to be connected to the VT must

be connected using the MSP port; the ESA-NET network must
therefore be connected over the ASP port or the field network. If the
VT is to be connected only to the ESA-NET network, the MSP can also
be used.
The VT can operate at a speed of from 38400 to 187500Baud; all partici-

pants in the network must be set to the same transmission speed.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
ESA-Net: Since serial communications are highly subject to disturbances, the follow-
Connecting ing advice should be followed to reduce as much as possible such prob-
the terminals lems:
It is absolutely necessary to use a fully shielded twisted serial cable, with
a pair of conductors having a minimum section of 0.22 mm and a char-
acteristic impedance of 120 Ohms.
It is absolutely necessary to use a fully shielded connector.
The termination resistances must be placed exclusively at the physical
extremes of the ESA-NET network.
Insert the polarization resistances of the appropriate value (typically 470
Ohms).
The shield of the cable must be soldered or mechanically connected to
the metal shells of the connectors that are connected subsequently to the
VTs in the network.
The VT serial connection cables must be laid in separate raceways

from the power supply cables.
The VT serial connection cables must be laid in separate raceways

from the power cables and from all the devices that may, in gen-
eral, be sources of disturbance (servo drives, inverters, etc...).
The table below shows the three connectors that can be used (MSP - ASP -
Field network) for ESA-NET network connections alongside the various
types of wiring according to position held within the network.
The VT connected in the network with a connector incorporating

three resistances must never be switched off while the other par-
ticipants in the network are still on. Should this happen, the effect of
the polarization resistances will be negated and there is a possibility
that communication errors will occur.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-17
VCC 16
470
1/4 W
TxRx+ 22
220
MSP - Connection: type A 1/4 W
TxRx- 10
470
25-pin connector with polari- 1/4 W
GND 7
zation and termination resi-
25
stances.
RTS 4
CTS 5
15
18
TxRx+ 22
120
MSP - Connection: type B 1/4 W
TxRx- 10
25-pin connector with termi-

GND 7
nation resistances.
25
RTS 4
CTS 5
15
18
TxRx+ 22
MSP - Connection: type C

TxRx- 10
25-pin connector.
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
VCC 13
470
1/4 W
ASP - Connection: type D TxRx+ 8
220
1/4 W
15-pin connector with polari- TxRx- 15
470
zation and termination resi- 1/4 W
stances. GND 7
RTS 10
CTS 11
ASP - Connection: type E TxRx+ 8

120
1/4 W
15-pin connector with termi- TxRx- 15
nation resistances.
RTS 10
CTS 11
ASP - Connection: type F TxRx+ 8
15-pin connector. TxRx- 15
RTS 10
CTS 11
Field network - Connec-

tion: type G TxRx+ 3
120
1/4 W
9-pin connector with termi- TxRx- 8
nation resistances.
Field network - Connec-

tion: type H TxRx+ 3
9-pin connector. TxRx- 8
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-19
There follows a table to use when making the ESA-NET network cable. To
use this table proceed as follows:
the layout of the VTs to be connected in the network;
define the port to be used for the network connection of each VT;
identify which VTs are physically at the extremes of the network;
specify which of the terminals at the extremes of the network will be first
and which last.
Beginning End
Extremes
#1 #2 #n-1 #n
Field
MSP ASP ASP
network
If, for any reason, the extremes are connected by a Field network
connector, one of the intermediate VT connections must still be
type A or D (depending on which connector is available).
Table 34.7: Construction of ESA-NET cable.

Wiring
Connector Position
A B C D E F G H
Initial -- -- -- -- -- -- --
MSP
Final -- -- -- -- -- -- --
25-pin
Intermediate -- -- -- -- -- -- --
Initial -- -- -- -- -- -- --
ASP
Final -- -- -- -- -- -- --
15-pin
Intermediate -- -- -- -- -- -- --
Initial -- -- -- -- -- -- --
Field network
Final -- -- -- -- -- -- --
9-pin
Intermediate -- -- -- -- -- -- --
The following page shows the cable needed for the connection as in the fig-
ure using 3 VT terminals.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
16
470
1/4 W
TxRx+ 22
220
1/4 W
TxRx- 10
VT1 connection using 470
25 pin MSP 1/4 W
GND 7
25
RTS 4
CTS 5
15
18
TxRx+ 8
VT2 connection using TxRx- 15

15 pin ASP
RTS 10
CTS 11
Connection using
TxRx+ 3
9 pin 120
RS485 serial module 1/4 W
(For this option see Chapter 33 -> TxRx- 8
RS485 Serial module)
ESA-Net: There is only 1 type of software used in configuring this network:

Configuration
software VTWIN
This software requires that you set parameters that coincide one with the other.
VTWIN:
The parameters that need to be set in the VTWIN project of each ter-
Terminals network address
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-21
ETHERNET VT terminals equipped with the right interface can be connected in a net-
work with other devices functioning by means of Transfer Control Proto-
col/Internet Protocol (TCP/IP).
The advantage of the Ethernet connection lies in the high speed of data
exchange it gives, (from 10Mbit/s to 100Mbit/s depending on the device
connected); secondly cabling is simplified indeed, the VT does not need
to be connected directly to the device but they can be interconnected using
a network concentrator; in addition, the number of possible network partic-
ipants is so high as to be practically limitless.
ETHERNET: The VTs communicate with the devices in a network by means of an

VT operation exchange of information on the form of small packages of data that are
managed by the TCP communication protocol. This splits up the informa-
tion and recomposes it once it arrives at its destination and it is responsible
for checking that all the information has arrived at the destination. The IP
protocol, on the other hand, is responsible for directing the information sent
to the right addressee. These protocols, TCP and IP, always work closely
together to ensure that the exchange of information functions correctly.
ETHERNET: There are two types of software that come into play when configuring this
Configuration network:
software
VTWIN
Software for configuring the device
These softwares require the setting of parameters that depend on the type of
network to which the terminal is connected.
VTWIN:
The parameters that need to be set in the VTWIN project of each ter-
minal connected in network are as follows:
IP Address
Subnet Mask
Any other parameters depending on the device connected
Equal IP addresses are not valid.
Software for configuring the device:
This software is supplied by the maker of the device.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
ETHERNET: The figure below shows two examples of connections: the first example
Connections shows a connection between a VT and a device using a direct connection,
while the second example shows a connection between VT and device
using a company network.
Example of direct connection between VT and Device.
VT Device
Direct connection
Crossed Ethernet cable
The layout in the diagram shows a crossed Ethernet network cable to be

used for direct connection between the VT and the device without using a
company network connection.
VT Side DEVICE Side

RJ45 8 pin RJ45 8 pin
Tx+ 1 1 Tx+
Rx+ 3 3 Rx+
Tx- 2 6 Rx-
Rx- 6 2 Tx-
8 8
7 7
6 6
5 5
4 4
3 3
2 2
1 1
Front Front
View View
NOTE: In this example we are not in a network context with other

devices so the IP address can be arbitrary.
The first three numbers of the IP address assigned must be the same as
those of the device with which it is to be connected, the fourth number must
be different. Example VT - 192.168.100.1, Device - 192.168.100.5
The other parameters remain those preset.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-23
Example of connection between VT and device using a company net-

work.
VT Device
Ethernet
The connection to the network uses an Ethernet Standard cable.
NOTE: All the parameters that need to be introduced depend on

the configuration of the network to which the connection is made.
You are, therefore, advised to contact the network administrator.
ETHERNET: If considered necessary, it is possible to check that the system is working

Checking the properly by running the command PING on a PC in the network.
connection
Go to the prompt of the PC commands and type ping followed by the IP
address assigned to the VT and/or the device and confirm with Enter (E.g.
ping 192.168.100.5).
If the connection and the settings have been executed correctly, response
strings will appear that contain the IP address requested. If, on the other
hand, what appears are strings indicating failure of the request this means
that there are connection problems; in this case the whole procedure includ-
ing the connection cable must be checked.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
CAN VT terminals equipped with the appropriate interface can be connected in a

network with other devices by means of a CAN (Controller Area Network)
protocol.
CAN terminals correspond to CIA DS 102 Version 2.0 (CAN Physical

Layer for Industrial Applications) specifications.
The CAN network differs from other types of network in its low cost, high
level performance in difficult electrical conditions, exceptional ability to
respond in real time and operational simplicity.
This type of network has a master/slave structure. The master device takes
care of initializing and configuring the slave stations, and further with con-
trolling the communication state of the devices in the network. The slave
devices are concerned exclusively with exchange of information. To be
able to communicate, the slave devices must be initialized (operational
state) and parameterized by the master device.
The VT can work at a speed ranging from 10kbit/s to 1000kbit/s.
CAN: VT The VTs communicate with the devices using logical channels to which
functioning in there correspond virtual communication lines which are independent of one
CAN network another and definible using certain parameters.
Logical channels can be of one of two types:
SDO (Service data object)

PDO (Process data object)
SDO channels concern themselves with the exchange of parameters for set-
ting, configuring and other information regarding the setting of the device.
PDO channels, on the other hand, concern themselves exclusively with
exchanging information related to the process underway.
PDO channels have priority over SDO channels.
It is possible to define the identifiers and lines of communication for all

SDOs and PDOs by using the TX and RX parameters; admissible values
run from 1 to 65535.
The network participants must each have a different address; the address of
the terminal is configured using VTWIN (see Software Manual).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-25
CAN: There is only one type of software that can effect the configuration of this
Configuration network:
software
VTWIN
This software requires the setting of parameters that coincide with one
another.
The parameters that have to be set in the VTWIN project of every

terminal connected in the network are:
Network address of the terminal.

SDO
PDO
CAN: The figure below shows the connection of VT with devices in a CAN net-
Connection work, in a master VT and slave formation.
Master
A
B B B A
Slave

1 2 127 128
Master
A
B B B A
Slave

1 2 127 128
Theoretically the network admits 128 devices, but the real limit depends on
how many logical channels are activated. The maximum number of chan-
nels is 64 SDO and 64 PDO.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 34
Example:
Suppose each devices possess 2 SDOs and 3 PDOs. If all are activated, the
maximum number of the devices that can be connected is 21, i.e. the overall
number of channels admissible divided by the number of PDO channels for
each device (because the PDO channels, being more numerous, determine
the limit).
Max. of channels allowed 64

Max. participants = =
Channels activated 3
As can be seen from the figure above, the connections for the devices at the
ends of the line (A) are different from the internal ones (B). Indeed, the A
connectors require cabling with a termination resistance for the line.
The VT terminals are already internally equipped with a termination resis-

tance, so in the first case (VT master) the resistance on the connector can be
omitted by using an integrated resistance. (See chapter on terminal to be
connected).
VTxxxH terminal cables always have terminations.
There follow diagrams of the types of connection.
Connector type A Connector type B

5 pin male 5 pin male
3 Shield
4 CAN +
3 Shield
2 CAN -
4 CAN + 1 V-
120
1/4 W
2 CAN -
1 V-
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

34-27
The recommended connection applies only to VTxxxH terminals.
Connection Connection
type A type B
White-Grey Shield
Yellow-White CAN +
White-Grey Shield
Blue CAN -
Yellow-White CAN + Green V-
Blue CAN - White-Grey

Yellow-White
Green V-
Blue
Green
The connection cable is already terminated on the VT side.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-1
Chapter 35 Operation of terminal with keyboard
Contents Page
Changing value of variable field 35-2
Total change 35-3
Partial change 35-3
Examples of varying fields 35-3
Displaying messages 35-8
Information messages 35-8
VT50 info-messages 35-8
VT60 info-messages 35-9
VT150W - VT160W info-messages 35-10
VT170W info-messages 35-10
VT300W - VT310W - VT320W info-messages 35-12
ISA-1A alarms 35-16
VT170W alarms 35-17
VT190W alarms 35-19
VT300W - VT310W - VT320W alarms 35-20
VT330W alarms 35-20
ISA-1A alarm history buffer 35-24
VT170W history buffer 35-25
VT300W - VT310W - VT320W history buffer 35-26
Help messages 35-29

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
35-2 Operation of terminal with keyboard
The contents of this chapter apply to all the VT terminals of the same fam-
ily that have a keyboard. As the of the various models differ in certain
details, the following explanations will indicate, for each , the respective
model.
The way a key functions changes according to the type of field to be varied.
Throughout the present chapter, when referring to the number of

rows and the number of characters that can be used in the termi-
nal, we assume native fonts are being used; when Windows-based fonts
are used (in the case of graphics ternminals only), the equivalent screen
area in pixels should be considered (see Software Manual Chapter 6 ->
Project language).
Changing value To be able to carry out a change in any editable variable field, the cursor
of variable field must first be positioned over the field involved by using
F2 F3
or
VT50
VT50 VT60 Others VT60 Others
and then pressing
F4 F4
Enter Enter
VT150W
VT50 VT60 VT160W Others
which enables the introduction of the new value.
The edit mode can be quit in two ways: either by saving after completing
the input of a value and pressing
F5 F4
Enter
Enter Enter
VT150W
or at any given moment without saving by pressing
Help
F1 Esc
Clr
Esc Esc
Esc
or automatically when the Input timeout (see Software Manual) elapses.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-3
The VT offers the following ways of changing a field:
Total change
Partial change
Total change This is the default mode adopted by the VT when enabling a change in a
field: numerical and alphanumeric fields behave differently.
Numerical fields:
The cursor flashes on the rightmost digit of the field. When the first
digit is introduced the rest of the field goes to zero, while the succes-
sive introductions make the digits shift to the left.
Alphanumeric field (ASCII):
The cursor flashes on the leftmost digit of the field. When the new
string is introduced sequentially the cursor moves one character to
the right.
Partial change With the edit mode enabled, pressing
F2 F3
or
VT50
VT50 VT60 Others VT60 Others
and then inputting a digit or character or pressing
Help F1 Info F2
or
VT50 VT60 VT50 VT60
enables the change of only that digit or character pointed to by the cursor;
to change the adjacent digits or characters the cursor must be positioned
manually (the figure above applies only to VT50 and VT60).
Examples of The examples below are offered to clarify how this works. For the sake of
varying fields simplicity we have chosen a single product, VT170W, but conceptually
what is said applies to all VTs, irrespective of what is written on the .
Changing the value of a decimal numerical field:
The following example demonstrates the variation (total change) of

field 1 from 9999 to -1234.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
Sample page Edit mode is enabled and the cur-

Field 1 9
9999 sor flashes on the rightmost digit
of the data (least significant digit).
D
E
Sample page
Press 1 to enter the first digit of
F
Field 1 1
0001 the new value; the field assumes
the value 1.
G J M
H K N
2 3 4
Press I L O
to complete
Sample page
Field 1 4
-1234 the new value; press Space
to
Enter
attribute a sign and to confirm
the change.
Changing the value of a floating point numerical field:
The procedure for changing a floating point numerical field is as for

a decimal numerical field, except that a decimal point can be inserted
anywhere in the field. The following example shows a variation
(total change) in field 2 from 10.3256 to 321.65.

Field 2 6
10.3256 sor flashes on the rightmost digit
J
K
Sample page
Press 3 to enter the first digit of
L
Field 2 3
0000003 the new value; the field assumes
the value 3.
Sample page G
H
D
E
1 2
Field 2 1
0000321 Press I
to complete the
F
whole numbers in the field.
Sample page shift
Field 2 .
000321.
Press + Space
to introduce the
decimal point.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-5
S P
T Q
6 5
Sample page Press U
to complete the
R
Field 2 5
0321.65 introduction of the new value.
Enter
Press to confirm the change.
Changing the value of a hexadecimal numerical field:
A hexadecimal digit can assume not only numerical values from 0 to

9 but also the letters A-B-C-D-E-F; thus for this type of field the
numerical 0 and 1 can be used to enter the letters A-B-C and
D-E-F respectively by pressing the same key more than once. All
the other from 2 to 9 have only a numerical significance. The fol-
lowing example illustrates the variation (total change mode) of field
3 from 1A3F to B23C.

Field 3 F
1A3F sor flashes on the rightmost digit
A
B
Sample page Press 0 three times to enter the

C
Field 3 B
000B first digit of the new value; the
field assumes in sequence the val-
ues 0, A and B.
G J A
H K B
Sample page Press I 32

, then press 0 4
L C
Field 3 C
B23C times to complete the new value;
Enter
The following example illustrates the variation (partial change) of

field 3 from B23C to BABA.

Field 3 C
B23C sor flashes on the rightmost digit
Sample page Position the cursor on the second

field 3 B23C
2
digit by pressing twice .
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
Sample page A
B
field 3 BA3C
A press 0 twice to change the digit
C
to the value A.
Position the cursor on the third

Sample page
digit by pressing and press
field 3 BABC
B A
B
0
C
three times to change the digit
to the value B.
Position the cursor on the last digit

A
B
Sample page
by pressing ; press 0 twice C
field 3 A
BABA
to change the digit to the value A.
Enter
Changing the value of an alphanumeric (ASCII) numerical field:
The following example illustrates the changing of field 4 from

MOTOR 1 to VALVE 3.5.

Field 4 sor flashes on the leftmost digit.
M
MOTOR 1
Sample page V
W
7
Field 4 Press once to enter the first
X
V
VOTOR 1 character of the new value.
The cursors movement by one

character to the right happens auto-
matically if the same is not
Sample page
pressed within a second or if a dif-
Field 4
VATOR
A 1 ferent alphanumeric is pressed;
it is always possible to reposition it
by pressing or .
Entering [A] as the second character will cause the cursor to move
automatically.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-7
J V
K W
3 7
Sample page Press L
3 times, X
once and
D
Field 4 E
1
VALVE
E 1 F
twice to complete word
VALVE.

Sample page
Press Space
to leave a space in the
Field 4 J
VALVE 3 K
3
field and then L
4 times.
shift
Press + Space
to enter the char-
Sample page P
Q
5
Field 4 acter [.]; press R
4 times to com-
VALVE 3.5
5
Enter
plete the new value; press to
confirm the change.
Changing the value of a dynamic text field:
The following example illustrates the variation of field 5 that can

assume 4 different states to which the following 4 symbolic texts cor-
respond: SETUP, STOP, MANUAL, AUTOMATIC.
Let us assume that SETUP is the starting value and MANUAL the
final one.

Field 5 sor flashes on the leftmost digit.
S
SETUP
Sample page PgUp
Field 5 The first time is pressed the

S
STOP field assumes the value STOP.
PgUp
The next time is pressed the

Sample page
field assumes the desired value,
Field 5
MANUAL
M Enter
that is MANUAL. Press to
confirm the change.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
Displaying The VT can display three types of message: Information messages,

messages ISA-1A Alarms (in the case of terminals accepting them) and Help mes-
sages (HELP pages). The information and alarm messages can only be
displayed if, using VTWIN, the programmer has already prepared the list of
messages assigned to areas of memory in the device.
Which type of message is used is at the discretion of the programmer.
Information When an event occurs which has an information message assigned to it the
messages LEDs of the following keys start flashing:
Info Help
Info Info
Esc
VT150W
Terminals VT50 and VT60 do not have LEDs, so there is no way

of understanding when an information message is present. You
are advised to define the priority of the messages with regard to the
page using the Exchange area Chapter 37 -> Command area (see also
Software Manual).
Information messages can be seen only when the event triggering them is
still present. When you press
Info Help
Shift + Info Info
Esc
VT150W
you enter display mode, indicated by a fixed LED light (where terminals
have them), which is so structured as to allow one page for each message,
that page have the following format (formats vary according to the type of
VT).
The VT can provide an automatic sequential display of information mes-
sages on command from the device (see Chapter 37 -> Command area).
VT50 Format:
info-messages
Two rows of 20 characters for the text of the message.
Example with two messages.
Pressure exceeds
safety limit
First message
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-9
Info
When you press the next message is displayed
Water level lower

than work threshold
Second message
Help
When you press the first message is displayed again:
Pressure exceeds
safety limit
First message
VT60 Format:
info-messages
Four rows of 20 characters for the text of the message.
Pressure exceeds
safety limit
First message
F2
When you press the next message is displayed:
Water level lower

than work threshold
Second message
F1
When you press the first message is displayed again.
Pressure exceeds
safety limit
First message
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
VT150W - Format:
VT160W
info-messages Two rows of 20 characters for the text of the message.
One row for any data field (which in that particular situation could indi-
cate a safety or warning limit value).
The first display is indicated by two characters [**] on the far right of the
third line of the display. These symbols are not present if the message
appeared when the display mode for information messages was accessed
on a previous occasion.
Pressure exceeds
safety limit
125.5 ** First message
PgDn
Water level lower

than work threshold
40 ** Second message
PgUp
Pressure exceeds
safety limit
VT170W Format:
info-messages
One row for the date and time the signal occurred.
appeared when the display mode for information messages was accessed
on a previous occasion.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-11
Pressure exceeds
safety limit
01/07/1998 10:45
PgDn
Water level lower

than work threshold
40 ** Second message
01/07/1998 10:46
PgUp
Pressure exceeds
a limit
01/07/1998 10:45
VT190W Format:
info-messages
appeared the last time the display mode for information messages was
accessed.
The pressure in the tank exceeds

first warning limit First message
125.5 **
01/07/1998 10:45
PgDn
The water level is lower than the

threshold enabling work to proceed Second message
40 **
01/07/1998 10:46
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
PgUp
The pressure in the tank exceeds

first warning limit First message
125.5 **
01/07/1998 10:45
VT300W - Format:
VT310W -
VT320W Five rows of 30 characters with character height of X1 or two rows of 15
info-messages with character height of X2 for the text of the message (VT300W -
VT310W).
Five rows of 36 characters with character height of X1 or two rows of 18
with character height of X2 for the text of the message (VT320W).
The first display is indicated by a closed envelope [ ] at the top left of
the display. This symbol is not present if the message appeared the last
time the display mode for information messages was accessed.
Example with two messages (VT310W).
Pressure exceeds
safety limit
First
message
125.5
01-07-1998 10:45a HELP PgDn
PgDn
shift
When you press + the second page containing the second message
appears. NB: having already appeared before, this message is not accompa-
nied by a closed envelope:
Temperature exceeds PgUp

safety limit
Second
message
1700
01-07-1998 10:55a HELP
PgUp
shift
When you press + the previous page is displayed again.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-13
Example with three messages (VT310W and VT320W).
Pressure exceeds
safety limit
First
message
125.5
01-07-1998 10:45a HELP Up
Temperature exceeds Down
safety limit
Second
message
1700
01-07-1998 10:55a HELP PgDn
PgDn
When you press you select the second message displayed as the cur-
rent message (the black bar indicates message has been selected). NB: hav-
ing already appeared before, this message is not accompanied by a closed
envelope:
Pressure exceeds
safety limit
First
message
125.5
01-07-1998 10:45a HELP Up
safety limit
Second
message
1700
01-07-1998 10:55a HELP PgDn
PgDn
When you press again you select the third message displayed as the
current message:
Temperature exceeds PgUp

safety limit
Second
message
1700
01-07-1998 10:55a HELP Up
Water level under Down

minimum level Third
message
-10
01-07-1998 11:00a HELP
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
PgUp
shift
When you press + the previous page appears containing the first
and second messages:
Pressure exceeds
safety limit
First
message
125.5
01-07-1998 10:45a HELP Up
safety limit
Second
message
1700
01-07-1998 10:55a HELP PgDn
VT330W Format:
info-messages
Four rows of 70 characters x1 high or two rows of 35 characters of dou-
ble height (x2) for the text of the message.
One row for the date and time the signal occured.
Example with five messages:
Pressure esxceeds safety limit

First
125.5 message
01-07-1998 10:45a
Temperature exceeds safety limit
Second
1700
message
01-07-1998 10:55a
Water level below min.

Third
-10
message
01-07-1998 11:00a
The level of gas saturation in the
boiler room has reached the first
warning level Fourth
345
message
01-07-1998 19:00a
PgDn
When you press you select the second message displayed as the cur-
rent message (the black bar indicates message has been selected). NB: hav-
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-15
ing already appeared before, this message is not accompanied by a closed

envelope:

First
125.5 message
01-07-1998 10:45a
Second
1700
message
01-07-1998 10:55a

Third
-10
message
01-07-1998 11:00a
345
message
01-07-1998 19:00a
PgDn
When you press again you select the third message displayed as the
current message:

First
125.5 message
01-07-1998 10:45a
Second
1700
message
01-07-1998 10:55a

Third
-10
message
01-07-1998 11:00a
345
message
01-07-1998 19:00a
PgDn
shift
When you press + the next page containing the fifth message
appears
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
Water pump stoppage

Fifth
message
01-07-1998 19:45a
PgUp
shift
When you press + the previous page returns containing the first
four messages:

First
125.5 message
01-07-1998 10:45a
Second
1700
message
01-07-1998 10:55a

Third
-10
message
01-07-1998 11:00a
345
message
01-07-1998 19:00a
ISA-1A alarms When an event occurs to which an alarm has been assigned, the following
LEDs begin to flash:
Hist Alarm
Alarm
VT50 VT60 VT150W VT160W VT320W Others
ISA alarms are displayed from the time when the event triggering the alarm
occurs (Event in) until there is an individual acknowledgment operation
using
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-17
Ack
Ack
All All Ack
Ack
or the global acknowledgment operation using
Ack
Ack
Shift + All
Ack
Shift + All Ack
(Event acknowledged) and the triggering event is no longer present (Event

out).
By acknowledgment we mean the confirmation on the part of the plant or

machine operator of having taken note of the alarm message.
For further details on how ISA-1A Alarms work see Software Manual.
When you press
Hist Alarm
Alarm
you enter display mode, signaled by the fixed light LED of that coming
on, where the first page has the format set out below (the format changes
according to the type of VT).
Alarm
When you press again you enter the second page whose format is set
out below (valid only for VT170W and VT190W).

VT170W The first page has the following format:

alarms
Numerical identification of the ISA-1A alarm.
Indication in the bottom right-hand corner of the display of:
Event appeared but not acknowledged; indicated by [!]
Event appeared, present and acknowledged; indicated by [*]
Event disappeared and not acknowledged; indicated by[#]
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
The second page has the following format:

One row starting with the character [>] for the date and time of the
appearance of the event (Event appears).
One row starting with:
the character [#] for the date and time of the Event acknowledged
but still present.
the character [<] for the date and time of the Event disappeared but
not acknowledged.
Example with two alarms.
Alarm n. 420
Pressure over the
maximum limit First page of the first alarm
150.0 !
The character [!] indicates that the alarm has not yet been acknowledged.
Ack
All
Ack
The acknowledgment operation, pressing , changes the character sig-
nalling the status of the event to [*]:
Alarm n. 420
Pressure over the
maximum limit First page of the first alarm
150.0 *
Alarm
When you press the second page appears:
Alarm n. 420
>01-07-1998 11:32a
#01-07-1998 11:38a Second page of the first alarm
Clr
Alarm Esc
When you press or the first page is appears again; by pressing
Clr
Esc
again you quit display mode for the ISA-1A alarms.
PgDn
If, while displaying the first page of the alarm, you pressing , the next
alarm message appears:
Alarm n. 470
Water level lower
than stop threshold First page of the second alarm
10 #
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-19
Alarm
Alarm n. 470
>01-07-1998 11:32a
<01-07-1998 11:37a Second page of the second alarm
The character [<] followed by the date and time, indicates that the event
triggering the alarm disappeared before the acknowledgment operation.
VT190W The first page has the following format:

alarms
Indication in the bottom right-hand corner of the display of:
Event in but not acknowledged; indicated by [!]
Event in, present and acknowledged; indicated by [*]
Event out and not acknowledged; indicated by[#]
The second page has the following format:

appearance of the event (Event in).
but still present.
the character [<] for the date and time of the Event out but not
acknowledged.
Example with two alarms.
Alarm n. 420
The pressure in the tank exceeds First page of the first alarm
the maximum limit
150.0 !
Il character [!] indicates that the alarm has not yet been acknowledged; this
Ack
All Ack
is emphasized by the LED of flashing; by pressing this key, the alarm
is acknowledged and the character indicating the status of the event
changes to [*] and the LED goes out.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
Alarm n. 420
The pressure in the tank exceeds First page of the first alarm
the maximum limit
150.0 *
Alarm
Alarm n. 420
>01-07-1998 11:32a Second page of the first alarm
#01-07-1998 11:38a
Clr Clr
Alarm Esc Esc
When you press or , the first page appears again; by pressing
again you quit display mode of the ISA-1A alarms.
PgDn
If, while displaying the first page of the alarm, you press , the next
alarm message appears
Alarm n. 470
Water level is lower than First page of the second alarm
the threshold stopping the process
10 #
Alarm
Alarm n. 420
>01-07-1998 11:32a Second page of the second
<01-07-1998 11:37a alarm
The character [<] followed by the date and time, indicates that the event
triggering the alarm disappeared before the acknowledgment operation.
VT300W - The page has the following format:

VT310W -
VT320W Numerical identification of the ISA-1A alarm.
alarms Four rows of 30 characters with character height of X1 or two rows of 15
with character height of X2 for the text of the message (VT300 -
VT310W).
Four rows of 36 characters with character height of X1 or two rows of 18
with character height of X2 for the text of the message (VT320W).
appearance of the event.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-21

but still present.
acknowledged.
Symbols indicating status of the alarm
Event in but not acknowledged [ ]
Event appeared, present and acknowledged [ ]
Event out and not acknowledged [ ]
Example with three alarms (VT300W).
The pressure in the tank

is over the max. limit
First
150.0 alarm
0001 >01-07-1998 11:32a
HELP PgDn
PgDn
shift
When you press + the second page appears containing the second
alarm. Note that the second alarm is accompanied by the character [<] fol-
lowed by the date and time, indicating that the event triggering the alarm
disappeared before the acknowledgment operation. All this is also empha-
sized by the appropriate symbol.
Water level is lower PgUp

than the threshold
for stopping the Second
process
10 alarm
0032 >01-07-1998 11:32a
<01-07-1998 11:37a HELP PgDn
PgDn
shift
When you press + the next page appears containing the third
alarm. Note that the second alarm is accompanied by the character [#] fol-
lowed by the date and time, indicating that the event triggering the alarm is
present and acknowledged. All this is also emphasized by the appropriate
symbol.
Temperature over the PgUp
safety limit Third alarm

1600
0006 >01-07-1998 12:28p
#01-07-1998 12:29p HELP
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
PgUp
shift
When you press + the previous page appears again.
Example with three alarms (VT310W and VT320W).

is over the maximum limit
First
alarm
150.0
0001 >01-07-1998 11:32a
HELP Up
Water level is Down
lower than the
threshold stopping the Second
process alarm
10
0032 >01-07-1998 11:32a
<01-07-1998 11:37a HELP PgDn
PgDn
When you press you select the second alarm as the current alarm. Note
that the second alarm is accompanied by the character [<] followed by the
date and time, indicating that the event triggering the alarm disappeared
before the acknowledgment operation. All this is also emphasized by the
appropriate symbol.

First
alarm
150.0
0001 >01-07-1998 11:32a
HELP Up
Water level lower Down
than the threshold
process alarm
10
0032 >01-07-1998 11:32a
<01-07-1998 11:37a HELP PgDn
PgDn
When you press again you select the third alarm as the current alarm.
Water level lower PgUp

than the threshold
process alarm
10
0032 >01-07-1998 11:32a
<01-07-1998 11:37a HELP Up
Temperature over the Down
safety limit Third

alarm
1600
0006 >01-07-1998 12:28p
#01-07-1998 12:29p HELP
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-23
PgUp
shift
When you press + the previous page appears containing the first
and second alarms. Note that the second alarm is accompanied by the char-
acter [#] followed by the date and time, indicating that the event triggering
the alarm is present and acknowledged. All this is also emphasized by the
appropriate symbol.

First
alarm
150.0
0001 >01-07-1998 11:32a
HELP Up
Water level is Down
lower than the
threshold stopping the Second
process alarm
10
0032 >01-07-1998 11:32a
<01-07-1998 11:37a HELP PgDn
VT330W The page has the following format:

alarms
Numeric identification of the ISA-1A alarm.
Four rows of 70 characters of x1 dimension or alternatively two rows of
35 double-size (x2) characters for the message text.
but still present.
acknowledged.
Graphic indication of the status of the alarm:
Event in and not acknowledged [ ]
Event in, present and acknowledged [ ]
Event out and not acknowledged. [ ]
Example with five alarms:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
Pressure in tank is over

safety limit
First
150.0 alarm
0001
>01-07-1998 11:32a
Water level is lower than
stop threshold of the process
Second
10
alarm
0032
>01-07-1998 11:32a <01-07-1998 11:37a
Temperature over Third

safety limit alarm
0006 1600
>01-07-1998 12:28p #01-07-1998 12:29p
PgDn
When you press you select the second alarm as the current alarm. Note
that the second alarm is accompanied by the character [<] followed by the date
and time, indicating that the triggering event of the alarm disappeared before
being acknowledged. The situation as a whole is highlighted by the appropriate
alarm status symbol. Third alarm is accompanied by the character [#] followed by
the date and time, indicating that the triggering event of the alarm is present and
has been acknowledged. The situation as a whole is highlighted by the appropri-
ate alarm status symbol.
ISA-1A alarm When an event occurs to which an alarm has been assigned the terminal
history buffer registers it chronologically in an area of the internal memory called the
Alarm history buffer. If, while displaying the first page of the alarm, you
Enter
press , or at any point
Shift + Hist Shift + Alarm

Alarm
you enter display mode, signaled by the fixed light LED of that coming
on.
Alarm
When you press again you enter the second page whose format is set
out below (valid only for VT170W and VT190W).

The buffer of the Alarm history can be emptied (the elimination of all the
messages registered) only by means of a command from the device (see
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-25
Chapter 37 -> Command area).
Once the buffer is full, new alarms are no longer registered. You
are advised to consult the chapter Status area of the VT Chapter
37 -> Status area for the terminal (see also Software Manual) to be able
to tell when the buffer is full.
The format is similar to that of the alarms except that a character [H] is
added in front of the number of the alarm (see the formats of the various
products).
VT170W Example with two alarms.

history buffer
H - Alarm n. 420
Pressure over the
maximum limit First page of history buffer of the first alarm
150.0
Alarm
H - Alarm n. 420
>01-07-1998 11:32a
#01-07-1998 11:38a Second page of history buffer of the first alarm
<01-07-1998 11:52a
Clr Clr
Alarm Esc Esc
When you press or the first page appears again; by pressing
again you quit the display mode for the history buffer.
PgDn
If, while displaying the first page of the history buffer, you press the
next message is displayed:
H - Alarm n. 470
Water level lower
than stop threshold First page of history buffer of the second alarm
10
Alarm
H - Alarm n. 470
>01-07-1998 11:32a
#01-07-1998 11:47a Second page of the second alarm
<01-07-1998 11:37a
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
VT190W Example with two alarms.

history buffer
H - Alarm n. 420
Pressure in the tank exceeds First page of the history buffe
the maximum limit of the first alarm
150.0
Alarm
H - Alarm n. 420
>01-07-1998 11:32a Second page of the history
#01-07-1998 11:38a buffer of the first alarm
<01-07-1998 11:52a
Clr
Alarm Esc
When you press or the first page is appears again; by pressing
Clr
Esc
again you quit display mode of the history buffer.
PgDn
If, while displaying the first page, you press , the next history buffer is
displayed:
H - Alarm n. 470
Water level lower than First page of the history buffe
threshold stopping process of the second alarm
10
Alarm
H - Alarm n. 470
>01-07-1998 11:32a Second page of the history
#01-07-1998 11:47a buffer of the second alarm
<01-07-1998 11:37a
VT300W - Example with three alarms VT300W.

VT310W -
VT320W
history buffer H Pressure in the tank
over maximum limit
0001
First
150.0 alarm
>01-07-1998 11:32a
<01-07-1998 11:33a
#01-07-1998 11:55a
PgDn
shift
When you press + the next page appears containing the following
alarm:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-27
H Water level is PgUp

lower than the
0032 threshold stopping
the process Second
10 alarm
>01-07-1998 11:32a
<01-07-1998 11:37a
#01-07-1998 11:40a PgDn
PgDn
shift
When you press + the next page appears containing the following
alarm:
H Temperature over the PgUp

0006 safety limit Third alarm
1600
>01-07-1998 12:28p
<01-07-1998 12:29p
#01-07-1998 12:29p
PgUp
shift
When you press + the previous page appears again. When you
Esc
press you quit display mode of the history buffer.
Example of three alarms VT310W and VT320W.
H Pressure in the tank

0001 First
150.0 alarm
>01-07-1998 11:32a
<01-07-1998 11:33a
#01-07-1998 11:55a Up
H Water level is Down
lower than the
0032 threshold stopping the Second
process
10 alarm
>01-07-1998 11:32a
<01-07-1998 11:37a
#01-07-1998 11:40a PgDn
PgDn
When you press you select the third alarm as the current alarm:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 35
H Water level is PgUp

lower than the
0032 threshold stopping the First
process
10 alarm
>01-07-1998 11:32a
<01-07-1998 11:37a
#01-07-1998 11:40a Up
H Temperature over the Down
0006 safety limit Second
1600 alarm
>01-07-1998 12:28p
<01-07-1998 12:29p
#01-07-1998 12:29p PgDn
PgUp
shift
When you press + the previous page now appears containing the
first and second alarms:

is over maximum limit
0001 First
150.0 alarm
>01-07-1998 11:32a
<01-07-1998 11:33a
#01-07-1998 11:55a Up
H Water level is Down
lower than the
0032 threshold for stopping the Second
process
10 alarm
>01-07-1998 11:32a
<01-07-1998 11:37a
#01-07-1998 11:40a PgDn
Esc
When you press you quit display mode for the history buffer.
VT330W Example with three alarms.

history buffer
Pressure in the tank is over

H the safety limit
First
0001 alarm
150.0
>01-07-1998 11:32a <01-07-1998 11:33a #01-07-1998 11:35a
Water level below the threshold
H level stopping the processo
Second
0032
10
alarm
>01-07-1998 11:32a <01-07-1998 11:37a #01-07-1998 11:40a
H Temperature over Third

0006 safety limit alarm
1600
>01-07-1998 12:28p <01-07-1998 12:29p #01-07-1998 12:29p
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

35-29
Esc
When you press you quit display mode for the history buffer.
Help When there is a help message the LED of the following keys flashes
messages
Help Help
Help Help
Esc
VT150W
Terminals VT50 and VT60 have no LEDs, so there is no way of

knowing when a help message is present.
Help messages can be assigned to project pages, to information messages

and to ISA alarms, giving additional information relevant to the operation
underway. Help messages have no particular format and can be freely cre-
ated by the programmer using the entire screen.
When you press
Help Help
Shift + Shift + Help Help
Esc
VT150W
you enter display mode, indicated by the fixed light of the LED (in the case
of those terminals that have it). When you press
Help
F1 Esc
Clr
Esc Esc
Esc
you quit display mode for help messages and return to the previous display
mode.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-1
Chapter 36 Operation of terminal with touch screen
Contents Page
Changing value of variable field 36-2
Total change 36-3
Partial change 36-3
Examples of varying fields 36-3
Displaying messages 36-19
Information messages 36-19
VT5xxH - VT1x5/505/515/525/555/56xW info-msgs 36-20
Vertical VT1x5W info-messages 36-21
VT575W - VT580W- VT585W - VT585WB info-messages 36-22
ISA-1A alarms 36-24
VT525H - VT1x5/515/525/555/56xW alarms 36-25
Vertical VT1x5W alarms 36-27
VT575W - VT580W - VT585W - VT585WB alarms 36-29
VT595W alarms 36-30
ISA-1A alarm history buffer 36-31
VT525H - VT1x5/515/525/555/56xW history buffer 36-32
Vertical VT1x5W history buffer 36-32
VT575W - VT580W - VT585W - VT585WB history buffer 36-33
Help messages 36-33
Help and information messages relating to alarms 36-34
Help messages relating to project pages 36-35

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
36-2 Operation of terminal with touch screen
The contents of this chapter apply to all the VT terminals of the same fam-
ily that have a touch screen.
Throughout the present chapter, when referring to the number of

rows and the number of characters that can be used in the termi-
nal, we assume native fonts are being used; when Windows-based fonts
are used (in the case of graphics ternminals only), the equivalent screen
area in pixels should be considered (see Software Manual Chapter 6 ->
Project language).
Changing value To be able to carry out a change in any editable variable field you must
of variable field touch the chosen field on the display and a page appears offering the
needed to modify the field.
The edit mode is quit by pressing the appropriate (see Table 36.1,
Chapter 36 -> Keys displayed used for settings .) after setting the value, or
automatically when the input timeout (see Software Manual) elapses,
whereby the variation is quit.
Table 36.1: Keys displayed used for settings (Part 1 of 2).
Keys Function
The function assumed depends on the type of field to be set.

Increases/decreases the value, the digit, the character.

Increases/decreases the value, the digit, the character.

Increases/decreases the value.
Allows you to move between digits or characters of the field.
Increases/decreases the value.
Allows you to move between digits or characters of the field
Confirms the setting of a field.

(For the sake of simplicity called Enter)
ESC Quits the setting of a field.
+/- Changes the sign when the field permits.
. Inserts the decimal point when the field permits.
0..9/a Numerical and alphanumeric keys.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-3
Table 36.1: Keys displayed used for settings (Part 2 of 2).
Keys Function
SHIFT In the case of an alphanumeric key allows the letter to be inserted.
The VT offers the following ways of changing a field:
Total change
Partial change
Total change This is the default mode adopted by the VT when enabling a change in a
numerical field.
Numerical fields:
The cursor flashes on the rightmost digit of the field. When the first
digit is introduced the rest of the field goes to zero, while the succes-
sive introductions make the digits shift to the left.
Partial change With the edit mode enabled, the change of the individual digit or character
being pointed to by the cursor is enabled by pressing the arrow and then
entering a digit, or by means of increasing the character (see Table 36.1,
Chapter 36 -> Keys displayed used for settings .). To change the adjacent
digits or characters the cursor has to be positioned manually.
Examples of The examples below are offered to clarify how this works. For the sake of
varying fields simplicity we have chosen a single product, VT555W, but conceptually
what is said applies to all the products of the same family.
Changing the value of a decimal numerical field:
The following example demonstrates the variation (total change) of

field 1 from 9999 to -1234.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
Sample page
Field 1 9999
Touch the display field [9999]
9999
0 1 2 3 ESC
. 4 5 6
+/- 7 8 9
Edit mode is enabled; the cursor moves to the right-

most digit of the data (least significant digit).
0001
0 1 2 3 ESC
. 4 5 6
+/- 7 8 9
Press the [1] to enter the first digit of the new

value; the field assumes the value 1.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-5
-1234
0 1 2 3 ESC
. 4 5 6
+/- 7 8 9
Press [2] [3] [4] to complete the entering of the

new value; press [+/-] to attribute a sign and
Enter to confirm.
Changing the value of a floating point numerical field:
The procedure for changing a floating point numerical field is as for

a decimal numerical field, except that a decimal point can be inserted
anywhere in the field. The following example shows a variation
(total change) in field 2 from 10.3256 to 321.65.
Sample page
Field 2 10.3256
Touch the display field [10.3256]
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
10.3256
0 1 2 3 ESC
. 4 5 6
+/- 7 8 9

0000003
0 1 2 3 ESC
. 4 5 6
+/- 7 8 9
Press the [3] to enter the first digit of the new

value; the field assumes the value 3.
0000321
0 1 2 3 ESC
. 4 5 6
+/- 7 8 9
Press [2] and then [1] to complete the whole

field.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-7
000321.
0 1 2 3 ESC
. 4 5 6
+/- 7 8 9
Press [.] to insert the decimal point.
0321.65
0 1 2 3 ESC
. 4 5 6
+/- 7 8 9
Press [6] and then [5] to complete the entering of

the new value; press Enter to confirm the varia-
tion.
Changing the value of a hexadecimal numerical field:
A hexadecimal digit can assume not only numerical values from 0 to

9 but also the letters A-B-C-D-E-F; thus for this type of field the
numerical 0 and 1 can be used to enter the letters A-B-C and
D-E-F respectively by pressing the same key more than once. All
the other from 2 to 9 have only a numerical significance. The fol-
lowing example illustrates the variation (total change mode) of field
3 from 1A3F to B23C.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
Sample page
Field 3 1A3F
Touch the display field [1A3F]
1A3F
0 1/a 2/b 3/c ESC
4/d 5/e 6/f
SHIFT 7 8 9
Edit mode is enabled; the cursor moves to the

rightmost digit of the data (least significant
digit).
000B
0 1/a 2/b 3/c ESC
4/d 5/e 6/f
SHIFT 7 8 9
Press [SHIFT] + [2/b] to enter the first digit of

the new value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-9
B23C
0 1/a 2/b 3/c ESC
4/d 5/e 6/f
SHIFT 7 8 9
Press [2/b] [3/c] and [SHIFT] + [3/c] to com-

plete the entering of the new value; press Enter
to confirm.
The following example shows the variation (partial change) of Field

3 from B23C to BABA.
Sample page
Field 3 B23C
Touch the display field [B23C]
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
B23C
0 1/a 2/b 3/c ESC
4/d 5/e 6/f
SHIFT 7 8 9

B23C
0 1/a 2/b 3/c ESC
4/d 5/e 6/f
SHIFT 7 8 9
Position the cursor on the second digit by press-

ing the [<-] twice.
BA3C
0 1/a 2/b 3/c ESC
4/d 5/e 6/f
SHIFT 7 8 9
Press [SHIFT] + [1/a] to enter the digit of the

new value.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-11
BABC
0 1/a 2/b 3/c ESC
4/d 5/e 6/f
SHIFT 7 8 9
Press [SHIFT] + [2/b] to enter the third digit of

the new value.
BABA
0 1/a 2/b 3/c ESC
4/d 5/e 6/f
SHIFT 7 8 9
Press [SHIFT] + [1/a] to enter the last digit of

the new value; press Enter to confirm the value.
Varying the value of alphanumeric (ASCII) field:
The following example shows the changing of Field 4 from MOTOR

1 to VALVE 3.5.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
Sample page
Field 4
MOTOR 1
Touch the display field [MOTOR 1]
VOTOR 1
ESC
Press [ ] or [ ] to poll all the characters of the

table of the font assigned (see Software Man-
ual); halt at the character [V].
VATOR 1
ESC
Press [->] to move to the next character, then

press [ ] or [ ] to poll all the characters until
reaching the character [A].
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-13
VALVE 3.5
ESC
Repeat the operations until the word is finished;

press Enter to confirm.
Changing the value of a dynamic text field:
The following example illustrates the variation of field 5 that can

assume 4 different states to which the following 4 symbolic texts cor-
respond: SETUP, STOP, MANUAL, AUTOMATIC.
Let us assume that SETUP is the starting value and MANUAL the
final one.
Sample page
Field 5
SETUP
Touch the display field [SETUP]
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
SETUP
ESC
Edit mode is enabled; the cursor moves to the

leftmost digit of the data.
STOP
ESC
The first time [ ] is pressed the field assumes the

value STOP.
MANUAL
ESC
The next time [ ] is pressed the field assumes the

value MANUAL; press Enter to confirm.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-15
Changing the value of a symbolic field:
The following example shows the variation of Field 6 that can

assume 4 different states to which are assigned the following 4
images:
Let us assume as a starting value and as a final value
Sample page
Field 6
Touch the display field [ ]
ESC
Edit mode is enabled.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
ESC
The first time [ ] is pressed the field assumes the

value .
ESC
The next time [ ] is pressed the field assumes the

value ; press Enter to confirm.
Varying the value of a binary field:
The following example illustrates the variation (total change) of

Field 7 from 1010 to 1111.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-17
Sample page
Field 7 1010
Touch the display field [1010]
1010
0 1 ESC

1111
0 1 ESC
Press [1] 4 times to enter the new value; press

Enter to confirm.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
Changing the value of a bar data:
The following example illustrates the variation of Field 8 that is to be

changed from a value of 100 to a value of 50.
Sample page
Field 8
Touch the display field [BAR]
MAX: 100
ESC
VAL: 100
MIN: 0
Edit mode is enabled.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-19
MAX: 100
ESC
VAL: 50
MIN: 0
Press [ ] to vary the value; take it to 50; press Enter

to confirm.
Displaying The VT can display three types of message: Information messages,

messages ISA-1A Alarms (in the case of terminals accepting them) and Help mes-
sages (HELP pages). The information and alarm messages can only be
displayed if, using VTWIN, the programmer has already prepared the list of
messages assigned to areas of memory in the device.
Which type of message is used is at the discretion of the programmer.
Information When an event occurs which has an information message assigned to it the
messages display shows
Note that the symbol is a triangle containing the character [i].
Information messages are only displayable so long as the event triggering

them is present. When the above symbol is touched on the screen you enter
display mode, where there is a page containing two messages with the fol-
lowing format (the format changes according to the VT).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
VT5xxH - Format:
VT1x5/505/515
/525/555/56xW Five rows of 30 characters with character height of X1 or two rows of 15
info-msgs with character height of X2 for the text of the message.
Example with three messages:
Pressure exceeds
safety limit
First
message
125.5 ESC
01-07-1998 10:45a HELP
Temperature over
safety limit
Second
message
1700
01-07-1998 10:55a HELP
By pressing [ ] the next page containing the third

message appears. NB: having already appeared
before, this second message is not accompanied
by a closed envelope.
Water level lower

than minimum limit Third
message
-10 ESC
01-07-1998 11:00a HELP
By pressing [ ] the previous page returns con-

taining the first and second messages.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-21
Vertical Format:
VT1x5W
info-messages Five rows of 21 characters with character height of X1 or three rows of
10 with character height of X2 for the text of the message.
Example with two messages:
HELP
Pressure exceeds
safety limit
125.5
First
message
01-07-1998 10:45a
ESC
By pressing [ ] the next page containing the second

message appears. NB: having already appeared
before, this second message is not accompanied by
a closed envelope.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
HELP
Water lev.
lower than
min. limit
-10
Second
message
01-07-1998 11:00a
ESC
By pressing [ ] the previous page returns con-

taining the first and first messages.
VT575W - Format:
VT580W-
VT585W - Four rows of 70 characters x1 high or two rows of 35 characters of dou-
VT585WB ble height (x2) for the text of the message.
info-messages One row for any data field (which in that particular situation could indi-
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-23

First
125.5 message
01-07-1998 10:45a
ESC Second
1700
message
01-07-1998 10:55a HELP

Third
-10
message
01-07-1998 11:00a HELP
345
message
01-07-1998 19:00a
By pressing [ ] the next page containing the

fifth message appears.
Water pump stoppage

Fifth
message
01-07-1998 19:45a
ESC
By pressing [ ] the previous page returns

containing the first four messages.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
VT595W Format:
info-messages
Four rows of 89 characters x1 high or two rows of 44 characters of dou-
ble height (x2) for the text of the message.

First
125.5 message
01-09-1998 10:45a
Second
ESC
1700 message
01-07-1998 10:55a HELP
Water level below min. Third
-10 message
01-07-1998 11:00a HELP
warning level
Fourth
345 message
01-07-1998 09:00a
Water pump stoppage
Fifth
message
01-07-1998 10:45a
NB: having already appeared before, the sec-

ond, fourth and fifth messages are not
accompanied by a closed envelope.
ISA-1A alarms When an event occurs to which an alarm has been assigned the screen
shows.
Note that the symbol is a triangle containing the character [i].
ISA alarms are displayed from the time when the event triggering the alarm
occurs (Event in) until there is an individual acknowledgment operation - touch-
ing the symbol on the screen related to the alarm to be acknowledged (Event
acknowledged) - and the triggering event is no longer present (Event out).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-25
By acknowledgment we mean the confirmation on the part of the plant or

machine operator of having taken note of the alarm message.
For further details on how ISA-1A Alarms work see Software Manual.
When the symbol on the screen is touched you enter display mode, where
each page contains up to two alarms whose format is set out below.

VT525H - The page has the following format:

VT1x5/515/525
/555/56xW Numerical identification of the ISA-1A alarm.
alarms Four rows of 30 characters with character height of X1 or two rows of 15
with character height of X2 for the text of the message.
but still present.
acknowledged.
Examples with three alarms:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36

exceeds the max. limit
First
alarm
150.0
0001 >01-07-1998 11:32a ESC
HELP
Water level is
lower than the HIST
stop threshold of the Second
process alarm
10
0032 >01-07-1998 11:32a
<01-07-1998 11:37a HELP
When you press [ ] the next page appears con-

taining the third alarm. Note that the second
alarm is accompanied by the character [<] fol-
lowed by the date and time, indicating that the
event triggering the alarm disappeared before
the acknowledgment operation. All this is also
emphasized by the appropriate symbol.
Temperature over the

safety limit Third
alarm
1600
0006 >01-07-1998 12:28p ESC
#01-07-1998 12:29p HELP
HIST
When you press [ ] the first page appears. Note

that the third alarm is accompanied by the char-
acter [#] followed by the date and time, indicat-
ing that the event triggering the alarm is present
and acknowledged. All this is also emphasized
by the appropriate symbol.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-27
Vertical The page has the following format:

VT1x5W
alarms Numerical identification of the ISA-1A alarm.
Five rows of 21 characters with character height of X1 or three rows of
10 with character height of X2 for the text of the message.
but still present.
acknowledged.
Examples with three alarms:
HELP
0001
The pressure in
the tank exceeds
the max. limit
150.0
First
alarm
>01-07-1998 11:32a
ESC HIST
When you press [ ] the next page appears con-

taining the second alarm. Note that the second
alarm is accompanied by the character [<] fol-
lowed by the date and time, indicating that the
event triggering the alarm disappeared before
the acknowledgment operation. All this is also
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
HELP
0032
Water level is
lower than the
stop threshold
of the process
10
Second
alarm
>01-07-1998 11:32a
<01-07-1998 11:37a
ESC HIST
When you press [ ] the first page appears. When

you press [ ] the next page appears containing
the third alarm. Note that the second alarm is
accompanied by the character [<] followed by
the date and time, indicating that the event trig-
gering the alarm disappeared before the
acknowledgment operation. All this is also
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-29
HELP
0006
Temperature
over the
safe lim.
1600
Third
alarm
>01-07-1998 12:28p
#01-07-1998 12:29p
ESC HIST
When you press [ ] the second page appears.
VT575W - The page has the following format:

VT580W -
VT585W - Numeric identification of the ISA-1A alarm.
VT585WB Four rows of 70 characters of x1 dimension or alternatively two rows of
alarms 35 double-size (x2) characters for the message text.
but still present.
acknowledged.
Example with three alarms:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36

safety limit
First
150.0 alarm
0001
>01-07-1998 11:32a HELP
ESC Second
10
alarm
0032
>01-07-1998 11:32a <01-07-1998 11:37a HELP

safety limit alarm
1600 HIST
0006
>01-07-1998 12:28p #01-07-1998 12:29p HELP
Note that the second alarm is accompanied by

the character [<] followed by the date and time,
indicating that the triggering event of the alarm
disappeared before being acknowledged. The
situation as a whole is highlighted by the appro-
priate alarm status symbol. Third alarm is
accompanied by the character [#] followed by
the date and time, indicating that the triggering
event of the alarm is present and has been
acknowledged. The situation as a whole is high-
lighted by the appropriate alarm status symbol.
VT595W The page has the following format:

alarms
Numeric identification of the ISA-1A alarm.
Four rows of 89 characters of x1 dimension or alternatively two rows of
44 double-size (x2) characters for the message text.
but still present.
acknowledged.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-31
Example with three alarms:

safety limit
First
0001 150.0 alarm
>01-07-1998 11:32a HELP
Second
ESC
0032 10 alarm
>01-07-1998 11:32a <01-07-1998 11:37a HELP
safety limit
0006 1600 alarm
>01-07-1998 12:28p #01-07-1998 12:29p HELP
Note that the second alarm is accompanied by

the character [<] followed by the date and time,
indicating that the triggering event of the alarm
disappeared before being acknowledged. The
situation as a whole is highlighted by the appro-
priate alarm status symbol. Third alarm is
accompanied by the character [#] followed by
the date and time, indicating that the triggering
event of the alarm is present and has been
acknowledged. The situation as a whole is high-
lighted by the appropriate alarm status symbol.
ISA-1A alarm When an event occurs to which an alarm has been assigned the terminal
history buffer registers it chronologically in an area of the internal memory called the
Alarm history buffer. If, while displaying the alarm page, you touch the
HIST on the screen, you access the history buffer.

The buffer of the Alarm history can be emptied (the elimination of all the
messages registered) only by means of a command from the device (see
Chapter 37 -> Command area).
Once the buffer is full, new alarms are no longer registered. You
are advised to consult the chapter Status area of the VT Chapter
37 -> Status area for the terminal (see also Software Manual) to be able
to tell when the buffer is full.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
The format is similar to that of the alarms except that a character [H] is added
in front of the number of the alarm (see the formats of the various products).
VT525H - Example with two alarms.

VT1x5/515/525
/555/56xW
history buffer over the maximum limit
0001 First
150.0 alarm
>01-07-1998 11:32a
<01-07-1998 11:33a ESC
#01-07-1998 11:55a
H Water level is
lower than the
0032 threshold stopping Second
the process
10 alarm
>01-07-1998 11:32a
<01-07-1998 11:37a
#01-07-1998 11:40a
When ESC is pressed you return to the display

mode for alarms.
Vertical Example with one alarm.

VT1x5W
history buffer
H
0001
The pressure in
the tank exceeds
the max. limit
150.0
First
alarm
>01-07-1998 11:32a
<01-07-1998 11:33a
#01-07-1998 11:55a
ESC
When ESC is pressed you return to the display

mode for alarm.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-33
VT575W - Example with three alarms.

VT580W -
VT585W -
Pressure in the tank is over
VT585WB H the safety limit
First
history buffer 0001
150.0 alarm
>01-07-1998 11:32a <01-07-1998 11:33a #01-07-1998 11:35a
Water level below the threshold
H level stopping the processo
ESC Second
0032
10
alarm
>01-07-1998 11:32a <01-07-1998 11:37a #01-07-1998 11:40a

0006 safety limit alarm
1600
>01-07-1998 12:28p <01-07-1998 12:29p #01-07-1998 12:29p
By pressing the ESC you return to the

alarm display.
VT595W Example with three alarms.

history buffer
H safety limit
First
0001 150.0 alarm
>01-07-1998 11:32a HELP
H stop threshold of the process
Second
ESC
0032 10 alarm
>01-07-1998 11:32a <01-07-1998 11:37a HELP

safety limit
0006 1600 alarm
>01-07-1998 12:28p #01-07-1998 12:29p HELP
By pressing the ESC you return to the

alarm display.
Help Help messages can be assigned to project pages, to information messages

messages and to ISA alarms, giving additional information relevant to the operation
underway. Help messages have no particular format and can be freely cre-
ated by the programmer using the entire screen.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 36
To explain the way the help messages work, it is necessary to divide them
into two categories: on the one hand messages related to alarms and to
information messages, on the other hand help messages related to pages.
Help and If, when you are in a context of displaying alarms or information messages,
information there is a help message present, the word HELP appears. If you touch the
messages alarm or the message accompanying the word HELP the help messaage is
relating to displayed. Touching the ESC on the screen takes you back to the previ-
alarms ous screenful.
The length of the message can be:
VT155W -> up to 34 (characters) x 16 (rows)

VT155W Vertical -> up to 21 (characters) x 24 (rows)
VT505H -> up to 34 (characters) x 16 (rows)
VT56xW -> up to 34 (characters) x 16 (rows)
VT585WB -> up to 74 (characters) x 16 (rows)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

36-35
Help As far as project pages are concerned, it is the programmers responsibility

messages to insert the necessary to access the help page (see Software Manual). If
relating to this is not done, there will be no way of telling if the page contains a help
project pages message.
The length of the message can be:

VT56xW -> up to 40 (characters) x 16 (rows)
VT585WB -> up to 80 (characters) x 16 (rows)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-1
Chapter 37 Data exchange area
Contents Page
Status area for the terminal 37-3
Status area for internal LEDs 37-8
Status area for external LEDs 37-12
Status area for recipes 37-14
Status area for internal keys 37-15
Status area for external keys 37-23
Status area for internal keys (Real Time) 37-25
Status area for external keys (Real Time) 37-25
Status area for printer 37-26
Status area for trends 37-28
Command response area 37-29
Command area external LEDs (fixed light) 37-30
Command area external LEDs (blinking light) 37-31
Command area internal red LEDs (fixed light) 37-32
Command area internal red LEDs (blinking light) 37-33
Command area internal green LEDs (fixed light) 37-34
Command area internal green LEDs (blinking light) 37-35
Command area 37-36

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
37-2 Data exchange area
By Communication we mean the exchange of information that occurs

between the VT and the device connected to it. Information can be
exchanged using Variables or Exchange Areas (see Software Manual for
more detailed explanation).
The Exchange Areas are divided into:
Area for Messages:

Information messages
Alarms
Status Areas:
Status area for the terminal
Status area for internal LEDs
Status area for external LEDs
Status area for recipes
Status area for internal keys
Status area for external keys
Status area for internal keys (Real Time)
Status area for external keys (Real Time)
Status area for printer
Trend status area
Command response area
Command Areas
Command area external LEDs (fixed light)
Command area external LEDs (blinking light)
Command area internal red LEDs (fixed light)
Command area internal red LEDs (blinking light)
Command area internal green LEDs (fixed light)
Command area internal green LEDs (blinking light)
Area for Commands
As the Area for Messages does not depend on the type of VT, but is com-
pletely configurable using VTWIN, it will no longer be mentioned in this
chapter.
For the detailed meaning of the various areas see Software Man-
ual.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-3
Status area for The significance of this area depends on the type of VT used:
the terminal With a keyboard
With a touch screen.
This area consists of 4 fixed words (numbered from 0 to 3).
With a keyboard:
NO. OF WORD NAME OF WORD

0 STATUS WORD
1 SEQUENCE IDENTIFIER
2 PAGE IDENTIFIER
3 FIELD IDENTIFIER
With a touch screen:

0 STATUS WORD
1 --
2 PAGE IDENTIFIER
3 CONTEXT IDENTIFIER
-- : not used
The tables appearing below refer to VTs with a keyboard.
37.1: Meaning of bits of Word 0 - Status word

37.2: Meaning of value contained in the Word 1 - Sequence Identifier
37.3: Meaning of value contained in the Word 2 - Page Identifier
37.4: Meaning of value contained in the Word 3 - Field Identifier
The tables appearing below refer to VTs with a touch screen.
37.5: Meaning of bits of Word 0 - Status word

37.6: Meaning of value contained in the Word 1
37.7: Meaning of value contained in the Word 2 - Page Identifier
37.8: Meaning of value contained in the Word 3 - Context Identifier
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Table 37.1: Meaning of bits of Word 0 - Status word

BIT NUMBER
WORD 0 VT VT VT VT VT VT VT VT VT VT
MEANING OF THE BIT 50 60 150 160 170 190 300 310 320 330
W W W W W W W W
WATCHDOG
0 0 0 0 0 0 0 0 0 0
Always at Status1
EDIT MODE
1 1 1 1 1 1 1 1 1 1
Status 1 when il terminal is in mode for changing fields
MESSAGES PRESENT
2 2 2 2 -- -- -- -- -- --
Status 1 so long as there is a message to display
MESSAGE PENDING
3 3 3 3 -- -- -- -- -- --
Status 1 so long as there is a message in but not yet consulted
ISA ALARM MESSAGES PRESENT

-- -- -- -- 2 2 2 2 2 2
Status 1 so long as there is an alarm message to display
ISA ALARM MESSAGES PENDING

Status 1 so long as there is an ISA alarm in but not yet -- -- -- -- 3 3 3 3 3 3
acknowledged
COMMAND NOT VALID

Status 1 when the last command sent by the device has not been 4 4 4 4 4 4 4 4 4 4
carried out
ALARM HISTORY BUFFER 80% FULL

Status 1 when the alarm history buffer is 80% full and therefore -- -- -- -- 5 5 5 5 5 5
close to saturation
ALARM HISTORY BUFFER FULL

Status 1 when the alarm history buffer is full and can hold no -- -- -- -- 6 6 6 6 6 6
more alarms
MACRO FUNCTION ACTIVE

-- -- 7 7 7 7 7 7 7 7
Status 1 when the VT is processing a macro function
BATTERY FLAT
Status 1 when the battery is near its minimum level for maintain- -- -- -- -- 8 8 8 8 8 8
ing the data in the RAM memory
-- : not present
Table 37.2: Meaning of value contained in the Word 1 - Sequence Identifier

USED
MEANING OF THE VALUE 50 60 150 160 170 190 300 310 320 330
W W W W W W W W
SEQUENCE IDENTIFIER
Contains a value other than zero if in Project Page context, but
contains zero if in any other context
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-5
Table 37.3: Meaning of value contained in the Word 2 - Page Identifier

USED / VALUE CONTAINED
W W W W W W W W
NUMBER OF PAGE BEING DISPLAYED
In Project Page context contains the value of the page being dis-

played, while contains the identifying value of the context if in
another contact (Word 1 = 0)
INFORMATION MESSAGES 0 0 0 0 0 0 0 0 0 0
SEQUENCE DIRECTORY 1 1 1 1 1 1 1 1 1 1
PAGE DIRECTORY -- -- -- -- -- -- -- -- -- --
DRIVER SERVICE PAGES 2 2 2 2 2 2 2 2 2 2
HELP MESSAGES FOR PROJECT PAGES -- -- 3 3 3 3 3 3 3 3
HELP MESSAGES FOR ISA ALARMS -- -- -- -- 4 4 4 4 4 4
ISA ALARMS -- -- -- -- 5 5 5 5 5 5
RECIPE DIRECTORY -- -- -- -- 6 6 6 6 6 6
HELP MESSAGES FOR INFORMATION MESSAGES -- -- 7 7 7 7 7 7 7 7
ALARM HISTORY BUFFER -- -- -- -- 8 8 8 8 8 8
PROJECT INFORMATION 3 3 -- -- 9 9 -- -- -- --
SETTING CLOCK -- -- -- -- 10 10 -- -- -- --
SYSTEM MESSAGES ASSIGNED TO RECIPES -- -- -- -- 11 11 -- -- -- --
SYSTEM MESSAGES ASSIGNED TO PASSWORDS -- -- -- -- 12 12 -- -- -- --
-- : not present
Table 37.4: Meaning of value contained in the Word 3 - Field Identifier

USED
W W W W W W W W
POSITION OF THE CURSOR
Contains a value identifying the field where the cursor is located

when in Project Page context, while containing 0 if in any other
context
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Table 37.5: Meaning of bits of Word 0 - Status word

BIT NUMBER
WORD 0 VT VT VT VT VT VT VT VT VT VT VT VT VT VT
MEANING OF THE BIT 155 185 505 505 515 525 525 555 56x 575 580 585 585 595
W W H W W H W W W W W W WB W
WATCHDOG
0 0 0 0 0 0 0 0 0 0 0 0 0 0
Always at Status1
EDIT MODE
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Status 1 when il terminal is in mode for changing fields
MESSAGES PRESENT
-- -- -- -- -- -- -- -- -- -- -- -- -- --
Status 1 so long as there is a message to display
MESSAGE PENDING
-- -- -- -- -- -- -- -- -- -- -- -- -- --
Status 1 so long as there is a message in but not yet consulted
ISA ALARM MESSAGES PRESENT

2 2 -- -- 2 2 2 2 2 2 2 2 2 2
Status 1 so long as there is an alarm message to display
ISA ALARM MESSAGES PENDING

Status 1 so long as there is an ISA alarm in but not yet 3 3 -- -- 3 3 3 3 3 3 3 3 3 3
acknowledged
COMMAND NOT VALID

Status 1 when the last command sent by the device has not been 4 4 4 4 4 4 4 4 4 4 4 4 4 4
carried out
ALARM HISTORY BUFFER 80% FULL

Status 1 when the alarm history buffer is 80% full and therefore 5 5 -- -- 5 5 5 5 5 5 5 5 5 5
close to saturation
ALARM HISTORY BUFFER FULL

Status 1 when the alarm history buffer is full and can hold no 6 6 -- -- 6 6 6 6 6 6 6 6 6 6
more alarms
MACRO FUNCTION ACTIVE

7 7 7 7 7 7 7 7 7 7 7 7 7 7
Status 1 when the VT is processing a macro function
BATTERY FLAT
Status 1 when the battery is near its minimum level for maintain- -- -- -- -- -- -- -- 8 8 -- -- 8 -- --
ing the data in the RAM memory
-- : not present
Table 37.6: Meaning of value contained in the Word 1

USED
WORD 1 VT VT VT VT VT VT VT VT VT VT VT VT VT
MEANING OF THE VALUE 155 185 505 505 515 525 525 555 56x 575 580 585 585
W W H W W H W W W W H W WB
-- -- -- -- -- -- -- -- -- -- -- -- -- --
-- : not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-7
Table 37.7: Meaning of value contained in the Word 2 - Page Identifier

USED
MEANING OF THE VALUE 155 185 505 505 515 525 525 555 56x 575 580 585 585 595
NUMBER OF PAGE BEING DISPLAYED

Contains a value other than zero if in Project Page context, but
contains zero if in any other context
Table 37.8: Meaning of value contained in the Word 3 - Context Identifier

USED / VALUE CONTAINED
MEANING OF THE VALUE 155 185 505 505 515 525 525 555 56x 575 580 585 585 595
CONTEXT IDENTIFIER
Contains the identifying value of the context if the context is not
Project Page (Word 2 = 0)
INFORMATION MESSAGES 0 0 0 0 0 0 0 0 0 0 0 0 0 0
SEQUENCE DIRECTORY -- -- -- -- -- -- -- -- -- -- -- -- -- --
PAGE DIRECTORY 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DRIVER SERVICE PAGES 2 2 2 2 2 2 2 2 2 2 2 2 2 2
HELP MESSAGES FOR PROJECT PAGES 3 3 3 3 3 3 3 3 3 3 3 3 3 3
HELP MESSAGES FOR ISA ALARMS 4 4 -- -- 4 4 4 4 4 4 4 4 4 4
ISA ALARMS 5 5 -- -- 5 5 5 5 5 5 5 5 5 5
RECIPE DIRECTORY 6 6 6 6 6 6 6 6 6 6 6 6 6 6
HELP MESSAGES FOR INFORMATION MESSAGES 7 7 7 7 7 7 7 7 7 7 7 7 7 7
ALARM HISTORY BUFFER 8 8 -- -- 8 8 8 8 8 8 8 8 8 8
PROJECT INFORMATION -- -- -- -- -- -- -- -- -- -- -- -- -- --
SETTING CLOCK -- -- -- -- -- -- -- -- -- -- -- -- -- --
SYSTEM MESSAGES ASSIGNED TO RECIPES -- -- -- -- -- -- -- -- -- -- -- -- -- --
SYSTEM MESSAGES ASSIGNED TO PASSWORDS -- -- -- -- -- -- -- -- -- -- -- -- -- --
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Status area for This area consists of a maximum of 4 words (numbered from 0 to 3).
internal LEDs
0 STATUS WORD for GREEN LEDS
1 STATUS WORD for GREEN LEDS
2 STATUS WORD for RED LEDS
3 STATUS WORD for RED LEDS
Table 37.9: Meaning of the Bits of the Status Word for the Green LEDs
MEANING OF THE BIT
WORD 0 VT VT VT VT VT VT VT VT
NUMBER OF THE BIT VT VT
150 160 170 190 300 310 320 330
50 60
W W W W W W W W
0 -- -- F1 F1 F1 F1 F1 F1 F1 --
1 -- -- F2 F2 F2 F2 F2 F2 F2 --
2 -- -- F3 F3 F3 F3 F3 F3 F3 --
3 -- -- F4 F4 F4 F4 F4 F4 F4 --
4 -- -- F5 F5 F5 F5 F5 F5 F5 --
5 -- -- -- -- F6 F6 F6 F6 F6 --
6 -- -- -- -- F7 F7 F7 F7 F7 --
7 -- -- -- -- F8 F8 F8 F8 F8 --
8 -- -- -- -- F9 F9 F9 F9 F9 --
9 -- -- -- -- F10 F10 F10 F10 F10 --
10 -- -- -- -- F11 F11 F11 F11 F11 --
11 -- -- -- -- F12 F12 F12 F12 F12 --
12 -- -- -- -- -- F13 F13 F13 F13 F13
13 -- -- -- -- -- F14 F14 F14 F14 F14
14 -- -- -- -- -- F15 F15 F15 F15 F15
15 -- -- -- -- -- F16 F16 F16 F16 F16
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-9
Table 37.10: Meaning of the Bits of the Status Word for Green LEDs
MEANING OF THE BIT
150 160 170 190 300 310 320 330
50 60
W W W W W W W W
0 -- -- -- -- -- F17 F17 F17 F17 F17
1 -- -- -- -- -- F18 F18 F18 F18 F18
2 -- -- -- -- -- F19 F19 F19 F19 F19
3 -- -- -- -- -- F20 F20 F20 F20 F20
4 -- -- -- -- -- F21 F21 F21 F21 F21
5 -- -- -- -- -- F22 F22 -- F22 F22
6 -- -- -- -- -- F23 F23 -- F23 F23
7 -- -- -- -- -- F24 F24 -- F24 F24
8 -- -- -- -- -- -- -- -- F25 F25
9 -- -- -- -- -- -- -- -- F26 F26
10 -- -- -- -- -- -- -- -- F27 F27
11 -- -- -- -- -- -- -- -- F28 F28
12 -- -- -- -- -- -- -- -- -- --
13 -- -- -- -- -- -- -- -- -- --
14 -- -- -- -- -- -- -- -- -- --
15 -- -- -- -- -- -- -- -- -- --
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Table 37.11: Meaning of the Bits of the Status Word for Red LEDs
MEANING OF THE BIT
150 160 170 190 300 310 320 330
50 60
W W W W W W W W
0 -- -- -- -- F1 F1 F1 F1 F1 --
1 -- -- -- -- F2 F2 F2 F2 F2 --
2 -- -- -- -- F3 F3 F3 F3 F3 --
3 -- -- -- -- F4 F4 F4 F4 F4 --
4 -- -- -- -- F5 F5 F5 F5 F5 --
5 -- -- -- -- F6 F6 F6 F6 F6 --
6 -- -- -- -- F7 F7 F7 F7 F7 --
7 -- -- -- -- F8 F8 F8 F8 F8 --
8 -- -- -- -- F9 F9 F9 F9 F9 --
9 -- -- -- -- F10 F10 F10 F10 F10 --
10 -- -- -- -- F11 F11 F11 F11 F11 --
11 -- -- -- -- F12 F12 F12 -- F12 --
12 -- -- -- -- -- F13 F13 -- F13 --
13 -- -- -- -- -- F14 F14 -- F14 --
14 -- -- -- -- -- F15 F15 -- F15 --
15 -- -- -- -- -- F16 F16 -- F16 --
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-11
Table 37.12: Meaning of the Bits of the Status Word for Red LEDs
MEANING OF THE BIT
150 160 170 190 300 310 320 330
50 60
W W W W W W W W
0 -- -- -- -- -- F17 F17 -- F17 --
1 -- -- -- -- -- F18 F18 -- F18 --
2 -- -- -- -- -- F19 F19 -- -- --
3 -- -- -- -- -- F20 F20 -- -- --
4 -- -- -- -- -- F21 F21 -- -- --
5 -- -- -- -- -- F22 F22 -- -- --
6 -- -- -- -- -- -- -- -- -- --
7 -- -- -- -- -- -- -- -- -- --
8 -- -- -- -- -- -- -- -- -- --
9 -- -- -- -- -- -- -- -- -- --
10 -- -- -- -- -- -- -- -- -- --
11 -- -- -- -- -- -- -- -- -- --
12 -- -- -- -- -- -- -- -- -- --
13 -- -- -- -- -- -- -- -- -- --
14 -- -- -- -- -- -- -- -- -- --
15 -- -- -- -- -- -- -- -- -- --
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Status area for This area consists of 2 fixed words (numbered from 0 to 1).
external LEDs
0 STATUS WORD
1 STATUS WORD
Table 37.13: Meaning of the Bits of the Status Word for External LEDs
NUMBER OF THE BIT
WORD 0 VT150W VT300W - VT310W - VT320W
MEANING OF THE BIT + VT160W +
VT100MT1000 VT100MT1000
E1 0 0 0
E2 1 1 1
E3 2 2 2
E4 3 3 3
E5 4 4 4
E6 5 5 5
E7 6 6 6
E8 7 7 7
E9 8 8 8
E10 9 9 9
E11 10 10 10
E12 11 11 11
E13 12 12 12
E14 13 13 13
E15 14 14 14
E16 15 15 15
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-13
Table 37.14: Meaning of the Bits of the Status Word for External LEDs
NUMBER OF THE BIT
MEANING OF THE BIT + VT160W +
VT100MT1000 VT100MT1000
E17 0 0 0
E18 1 1 1
E19 2 -- 2
E20 3 -- 3
E21 -- -- --
E22 -- -- --
E23 -- -- --
E24 -- -- --
E25 -- -- --
E26 -- -- --
E27 -- -- --
E28 -- -- --
E29 -- -- --
E30 -- -- --
E31 -- -- --
E32 -- -- --
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Status area for This area consists of 1 word (numbered 0).

recipes
0 STATUS WORD for RECIPES
Table 37.15: Meaning of the Bits of the Status Word for Recipes
NUMBER OF THE BIT
MEANING OF THE BIT 50 60 150 160 170 190 300 310 320 330
W W W W W W W W
TIMEOUT FOR RECIPE TRANSFER
Status 1 when the terminal does not respond in the -- -- -- -- 13 13 13 13 13 13
expected time
TRANSFER OVER
Status 1 when the terminal has sent all the relevant -- -- -- -- 14 14 14 14 14 14
data
TRANSFER REQUEST
-- -- -- -- 15 15 15 15 15 15
Status 1 when the terminal wants to start to transfer
-- : not present
Table 37.16: Meaning of the Bits of the Status Word for Recipes
NUMBER OF THE BIT
WORD 0 VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT
MEANING OF THE BIT 155 185 505 505 515 155 185 505 505 525 525 555 56x 575 580 585 585 595
W W H W W W W H W H W W W W W W WB W
TIMEOUT FOR RECIPE TRANSFER
Status 1 when the terminal does not respond in the 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13
expected time
TRANSFER OVER
Status 1 when the terminal has sent all the relevant 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14
data
TRANSFER REQUEST
15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15
Status 1 when the terminal wants to start to transfer
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-15
internal keys With a keyboard
With a touch screen.
With a keyboard: this area consists of a maximum of 6 words (numbered

from 0 to 5).

0 OPERATIVE KEYS STATUS
4 FUNCTION KEYS STATUS
With a touch screen: this area consists of 1 word.

The tables appearing below refer to VTs with a keyboard.
37.17: Meaning of the Bits of the Status Word for Internal Keys (Word 0)
The tables appearing below refer to VTs with a touch screen.
The keys enclosed in a box with a bold border put the related bit at 1 when
Shift
pressed with .
The above is valid for VT50 and VT60. In the case of other termi-
nals the bits relating to the function keys are always the same. The
bit of the SHIFT key must also be tested (Word 0 - Bit 15).
Shift
The bit relating to the key is set at 1 only if pressed at the same time as
Clr
Shift Esc
another key (e.g. + ).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
The Handshake bit is put at 1 by the VT each time one or more keys are pressed;
the device can put it at 0 in order to find out when the VT is going to write.
Table 37.17: Meaning of the Bits of the Status Word for Internal Keys (Word 0)
WORD 0
BIT
Shift VT50 VT60 VT150W VT160W VT170W VT190W VT300W VT310W VT320W VT330W
HAND HAND HAND HAND HAND HAND HAND HAND HAND HAND
0
SHAKE SHAKE SHAKE SHAKE SHAKE SHAKE SHAKE SHAKE SHAKE SHAKE
Help
1
F1 Clr Clr Clr Clr Clr Clr Clr
Esc
Esc Esc Esc Esc Esc Esc Esc Esc
Esc
2
F2 --
3
F3 F3
4
F4 F4
Enter Enter Enter
5
F5 F4 -- -- Enter Enter Enter Enter Enter Enter
Enter
6
Info F2 PgDn PgDn PgDn PgDn PgDn PgDn PgDn PgDn
7
Help F1 PgUp PgUp PgUp PgUp PgUp PgUp PgUp PgUp
F1 F1
8 Help Help Info Info Info Info Info Info
Esc
F2 F2
9 Info Info Help Help Help Help Help Help
F3 F3 Hist
10 -- -- Alarm Alarm Alarm Alarm Hist
Alarm Alarm
11
F4 F4 -- --
Ack
All
Ack Ack Ack Ack Ack
Ack All Ack All Ack All Ack All Ack All
Ack
Enter
12
F5 -- .
. Space
Space Space Space Space Space Space Space
Help Help
13 -- --
Esc
Info Help
14 -- -- -- -- Spare Spare -- Clr
Esc
15 -- -- shift shift shift shift shift shift shift Shift
-- : not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-17
WORD 1
BIT
A A A A A A A
0 n.p. n.p. B B B B B B B Ctrl
C 0 C 0 C 0 C 0 C 0 C 0 C 0
D D D D D D D
1 n.p. n.p. E E E E E E E Alt
F 1 F 1 F 1 F 1 F 1 F 1 F 1
G G G G G G G
2 n.p. n.p. H H H H H H H Tab
I 2 I 2 I 2 I 2 I 2 I 2 I 2
J J J J J J J
3 n.p. n.p. K K K K K K K Spare
L 3 L 3 L 3 L 3 L 3 L 3 L 3
M M M M M M M
4 n.p. n.p. N N N N N N N
<
O 4 O 4 O 4 O 4 O 4 O 4 O 4 ,
P P P P P P P
>
5 n.p. n.p. Q
5
Q
5
Q
5
Q
5
Q
5
Q
5
Q
5 .
R R R R R R R
S S S S S S S _
6 n.p. n.p. T T T T T T T
U 6 U 6 U 6 U 6 U 6 U 6 U 6 -
V V V V V V V
7 n.p. n.p. W W W W W W W +
X 7 X 7 X 7 X 7 X 7 X 7 X 7 =
Y Y Y Y Y Y Y
8 n.p. n.p. Z Z Z Z Z Z Z --
- 8 - 8 - 8 - 8 - 8 - 8 - 8
+ + + + + + +
9 n.p. n.p. / / / / / / / --
= 9 = 9 = 9 = 9 = 9 = 9 = 9
10 n.p. n.p. -- -- -- -- -- -- -- --
11 n.p. n.p. -- -- -- -- -- -- -- --
12 n.p. n.p. -- -- -- -- -- -- -- --
13 n.p. n.p. -- -- -- -- -- -- -- --
14 n.p. n.p. -- -- -- -- -- -- -- --
15 n.p. n.p. -- -- -- -- -- -- -- --
-- : not used n.p. : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
WORD 2
BIT
0 n.p. n.p. F6 F6 )
F1 F1
F1 F1 F1 F1 F1 0
1 n.p. n.p. F7 F7 /
F2 F2
F2 F2 F2 F2 F2 1
2 n.p. n.p. F8 F8 \
F3 F3
F3 F3 F3 F3 F3 2
3 n.p. n.p. F9 F9 ]
F4 F4
F4 F4 F4 F4 F4 3
4 n.p. n.p. F10 F10 :

F5 F5
F5 F5 F5 F5 F5 4
5 n.p. n.p. -- -- %
F6 F6 F6 F6 F6 5
6 n.p. n.p. -- -- [
F7 F7 F7 F7 F7 6
7 n.p. n.p. -- -- ;
F8 F8 F8 F8 F8 7
8 n.p. n.p. -- -- *
F9 F9 F9 F9 F9 8
9 n.p. n.p. -- -- (
F10 F10 F10 F10 F10 9
10 n.p. n.p. -- -- --
F11 F11 F11 F11 F11
11 n.p. n.p. -- --
F12 F12 F12 F12 F12
--
12 n.p. n.p. -- -- --
F13 F13 F13 F13
--
13 n.p. n.p. -- -- --
F14 F14 F14 F14
--
14 n.p. n.p. -- -- --
F15 F15 F15 F15
--
15 n.p. n.p. -- -- --
F16 F16 F16 F16
--
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-19
WORD 3
BIT
A
0 n.p. n.p. n.p. n.p. n.p.
F17 F17 F17 F17 B
C
1 n.p. n.p. n.p. n.p. n.p.
F18 F18 F18 F18 D
E
2 n.p. n.p. n.p. n.p. n.p.
F19 F19 F19 F19 F
G
3 n.p. n.p. n.p. n.p. n.p.
F20 F20 F20 F20 H
I
4 n.p. n.p. n.p. n.p. n.p.
F21 F21 F21 F21 J
5 n.p. n.p. n.p. n.p. n.p. -- K

F22 F22 F22 L
M
6 n.p. n.p. n.p. n.p. n.p. F23 F23 -- F23 N
O
7 n.p. n.p. n.p. n.p. n.p. F24 F24 -- F24 P
Q
8 n.p. n.p. n.p. n.p. n.p. -- -- -- F25 R
S
9 n.p. n.p. n.p. n.p. n.p. -- -- -- F26 T
U
10 n.p. n.p. n.p. n.p. n.p. -- -- -- F27 V
W
11 n.p. n.p. n.p. n.p. n.p. -- -- -- F28 X
12 n.p. n.p. n.p. n.p. n.p. -- -- -- -- Y

Z
13 n.p. n.p. n.p. n.p. n.p. -- -- -- -- --
14 n.p. n.p. n.p. n.p. n.p. -- -- -- -- --
15 n.p. n.p. n.p. n.p. n.p. -- -- -- -- --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
WORD 4
BIT
0 n.p. n.p. n.p. n.p. n.p. n.p. n.p. n.p. n.p. F1
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-21
WORD 5
BIT
12 n.p. n.p. n.p. n.p. n.p. n.p. n.p. n.p. n.p. --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
WORD 0
BIT
VT505H VT52H
0 HAND SHAKE HAND SHAKE
1 F1 F1
2 F2 F2
3 F3 F3
4 F4 F4
5 F5 F5
6 F6 F6
7 F7 F7
8 F8 F8
9 F9 F9
10 F10 F10
11 -- --
12 -- --
13 -- --
14 -- --
15 -- --
-- : not used n.p. : non presente
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-23
external keys
0 STATUS WORD for EXTERNAL KEYS
1 STATUS WORD for EXTERNAL KEYS
Table 37.24: Meaning of the Bits of the Status Word for External Keys
NUMBER OF THE BIT
MEANING OF BIT + VT160W +
VT100MT1000 VT100MT1000
E1 0 0 0
E2 1 1 1
E3 2 2 2
E4 3 3 3
E5 4 4 4
E6 5 5 5
E7 6 6 6
E8 7 7 7
E9 8 8 8
E10 9 9 9
E11 10 10 10
E12 11 11 11
E13 12 12 12
E14 13 13 13
E15 14 14 14
E16 15 15 15
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Table 37.25: Meaning of the Bits of the Status Word for External Keys
NUMBER OF THE BIT
VT100MT1000 VT100MT1000
E17 0 0 0
E18 1 1 1
E19 2 -- 2
E20 3 -- 3
E21 -- -- --
E22 -- -- --
E23 -- -- --
E24 -- -- --
E25 -- -- --
E26 -- -- --
E27 -- -- --
E28 -- -- --
E29 -- -- --
E30 -- -- --
E31 -- -- --
E32 -- -- --
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-25
internal keys With a keyboard
(Real Time) With a touch screen.
With a keyboard: this area consists of a maximum of 6 words (numbered

from 0 to 5).
WORD NUMBER NAME OF WORD

0 OPERATIVE KEYS STATUS (Real Time)
4 FUNCTION KEYS STATUS (Real Time)
With a touch screen: this area consists of 1 word.

The keys surrounded by a bold border set the corresponding bit at 1 when
Shift
pressed together with .
The above is valid for VT50 and VT60. In the case of other termi-
nals the bits relating to the function keys are always the same. The
bit of the SHIFT key must also be tested (Word 0 - Bit 15).
Shift
The bit relating to the key is set at 1 only if pressed at the same time as
Clr
Shift Esc
another key (e.g. + ).
The Handshake bit is set at 1 by the VT whenever one or more keys are
pressed; it is set at 0 when no key is pressed.
For details concerning these Status words, see Page 37-15.
external keys
(Real Time) WORD NUMBER NAME OF WORD
0 STATUS WORD FOR EXTERN. KEYS (Real Time)
1 STATUS WORD FOR EXTERN. KEYS (Real Time)
For details concerning these Status words, see Page 37-23.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Status area for This area consists of 2 words (numbered from 0 to 1).
printer
0 STATUS WORD for ASP
1 STATUS WORD for LPT
Table 37.26: Meaning of the Bits of the Status Word for ASP
NUMBER OF THE BIT
WORD 0 VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT
MEANING OF THE BIT 50 60 150 160 170 190 300 310 320 330 155 185 505 505 515 525 525 555 56x 575 580 585 585 595
W W W W W W W W W W H W W H W W W W W W WB W
STAMPANTE NOT ON
LINE
n.p. n.p. n.p. n.p. 0 0 0 0 0 0 0 0 n.p. n.p. n.p. 0 0 0 0 0 0 0 0 0
Status 1 when one of the
bits from 3 to 8 is set at 1.
TIMEOUT
Status 1 when the printer is
OFFLINE, not connected,
n.p. n.p. n.p. n.p. 1 1 1 1 1 1 1 1 n.p. n.p. n.p. 1 1 1 1 1 1 1 1 1
lacks paper or when there is
any communication problem
follow the command to print.
-- n.p. n.p. n.p. n.p. -- -- -- -- -- -- -- -- n.p. n.p. n.p. -- -- -- -- -- -- -- -- --
REPORT PRINTING IN
PROGRESS
n.p. n.p. n.p. n.p. 3 3 3 3 3 3 3 3 n.p. n.p. n.p. 3 3 3 3 3 3 3 3 3
Status 1 as long as the
function lasts
DIRECT PRINTING OF
THE INFORMATION
MESSAGE IN
n.p. n.p. n.p. n.p. 4 4 4 4 4 4 4 4 n.p. n.p. n.p. 4 4 4 4 4 4 4 4 4
PROGRESS
function lasts
DIRECT PRINTING OF
THE ISA ALARME IN
PROGRESS n.p. n.p. n.p. n.p. 5 5 5 5 5 5 5 5 n.p. n.p. n.p. 5 5 5 5 5 5 5 5 5
function lasts
PRINTING OF ALARM
HISTORY BUFFER IN
PROGRESS n.p. n.p. n.p. n.p. 6 6 6 6 6 6 6 6 n.p. n.p. n.p. 6 6 6 6 6 6 6 6 6
function lasts
HARDCOPY IN
PROGRESS
n.p. n.p. n.p. n.p. 7 7 7 7 7 7 7 7 n.p. n.p. n.p. 7 7 7 7 7 7 7 7 7
function lasts
FORM-FEED IN
PROGRESS
n.p. n.p. n.p. n.p. 8 8 8 8 8 8 8 8 n.p. n.p. n.p. 8 8 8 8 8 8 8 8 8
function lasts
-- : non used n.p. : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-27
Table 37.27: Meaning of the Bits of the Status Word for LPT
NUMBER OF THE BIT
MEANING OF THE BIT 50 60 150 160 170 190 300 310 320 330 155 185 505 505 515 525 525 555 56x 575 580 585 585 595
STAMPANTE NOT ON
LINE
n.p. n.p. n.p. n.p. 0 0 0 0 0 0 n.p. n.p. n.p. n.p. n.p. n.p. n.p. 0 0 0 0 0 0 0
Status 1 when one of the
bits from 3 to 8 is set at 1.
TIMEOUT
Status 1 when the printer is
OFFLINE, not connected,
lacks paper or when there is
any communication problem
follow the command to print.
-- n.p. n.p. n.p. n.p. -- -- -- -- -- -- n.p. n.p. n.p. n.p. n.p. n.p. n.p. -- -- -- -- -- -- --
REPORT PRINTING IN
PROGRESS
function lasts
DIRECT PRINTING OF
THE INFORMATION
MESSAGE IN
PROGRESS
function lasts
DIRECT PRINTING OF
THE ISA ALARME IN
PROGRESS n.p. n.p. n.p. n.p. 5 5 5 5 5 5 n.p. n.p. n.p. n.p. n.p. n.p. n.p. 5 5 5 5 5 5 5
function lasts
PRINTING OF ALARM
HISTORY BUFFER IN
PROGRESS n.p. n.p. n.p. n.p. 6 6 6 6 6 6 n.p. n.p. n.p. n.p. n.p. n.p. n.p. 6 6 6 6 6 6 6
function lasts
HARDCOPY IN
PROGRESS
function lasts
FORM-FEED IN
PROGRESS
function lasts
-- : non used n.p. : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Status area for This area consists of 1 word.

trends
0 TREND STATUS WORD
Table 37.28: Meaning of bits of Trend Status Word

NUMBER OF THE BIT
MEANING OF BIT 50 60 150 160 170 190 300 310 320 330 155 185 505 505 515 525 525 555 56x 575 580 585 585 585
TREND NUMBER 1 BUFFER

FULL n.p. -- -- -- -- -- 0 0 0 0 -- 0 -- -- -- -- -- 0 0 0 0 0 0 0
Status 1when the buffer is full.

FULL n.p. -- -- -- -- -- 1 1 1 1 -- 1 -- -- -- -- -- 1 1 1 1 1 1 1

FULL n.p. -- -- -- -- -- 2 2 2 2 -- 2 -- -- -- -- -- 2 2 2 2 2 2 2

FULL n.p. -- -- -- -- -- 3 3 3 3 -- 3 -- -- -- -- -- 3 3 3 3 3 3 3

FULL n.p. -- -- -- -- -- 4 4 4 4 -- 4 -- -- -- -- -- 4 4 4 4 4 4 4

FULL n.p. -- -- -- -- -- 5 5 5 5 -- 5 -- -- -- -- -- 5 5 5 5 5 5 5

FULL n.p. -- -- -- -- -- 6 6 6 6 -- 6 -- -- -- -- -- 6 6 6 6 6 6 6

FULL n.p. -- -- -- -- -- 7 7 7 7 -- 7 -- -- -- -- -- 7 7 7 7 7 7 7

FULL n.p. -- -- -- -- -- 8 8 8 8 -- 8 -- -- -- -- -- 8 8 8 8 8 8 8
TREND NUMBER 10
BUFFER FULL n.p. -- -- -- -- -- 9 9 9 9 -- 9 -- -- -- -- -- 9 9 9 9 9 9 9
TREND NUMBER 11
BUFFER FULL n.p. -- -- -- -- -- 10 10 10 10 -- 10 -- -- -- -- -- 10 10 10 10 10 10 10
TREND NUMBER 12
BUFFER FULL n.p. -- -- -- -- -- 11 11 11 11 -- 11 -- -- -- -- -- 11 11 11 11 11 11 11
TREND NUMBER 13
BUFFER FULL n.p. -- -- -- -- -- 12 12 12 12 -- 12 -- -- -- -- -- 12 12 12 12 12 12 12
TREND NUMBER 14
BUFFER FULL n.p. -- -- -- -- -- 13 13 13 13 -- 13 -- -- -- -- -- 13 13 13 13 13 13 13
TREND NUMBER 15
BUFFER FULL n.p. -- -- -- -- -- 14 14 14 14 -- 14 -- -- -- -- -- 14 14 14 14 14 14 14
TREND NUMBER 16
BUFFER FULL n.p. -- -- -- -- -- 15 15 15 15 -- 15 -- -- -- -- -- 15 15 15 15 15 15 15
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-29
Command This area consists of 4 fixed words (numbered from 0 to 3).

response area
0 COMMAND
1 PARAMETER 1
2 PARAMETER 2
3 PARAMETER 3
Below are listed commands with their responses:
COMMAND 14: Reads current time

Word Value/Meaning
0 14
1 HH -> Hours in BCD MM -> Minutes in BCD
2 SS -> Seconds in BCD Not used
3 Not used
COMMAND 15: Reads current date

Word Value/Meaning
0 15
1 GG -> Day in BCD MMM -> Month in BCD
2 AAAA -> Year in BCD
3 DOW -> Day of the week (0=Sunday) Not Used
For examples of the use of this area see Software Manual.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37

area external
LEDs (fixed WORD NUMBER NAME OF WORD
light)
0 WORD COMMANDING EXTERNAL LEDS
Table 37.29: Meaning of Bits of Word Commanding External LEDs (fixed light)
BIT NUMBER
VT100MT1000 VT100MT1000
E1 0 0 0
E2 1 1 1
E3 2 2 2
E4 3 3 3
E5 4 4 4
E6 5 5 5
E7 6 6 6
E8 7 7 7
E9 8 8 8
E10 9 9 9
E11 10 10 10
E12 11 11 11
E13 12 12 12
E14 13 13 13
E15 14 14 14
E16 15 15 15
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-31
Table 37.30: Meaning of Bits of Word Commanding External LEDs (fixed light)
BIT NUMBER
VT100MT1000 VT100MT1000
E17 0 0 0
E18 1 1 1
E19 2 -- 2
E20 3 -- 3
E21 -- -- --
E22 -- -- --
E23 -- -- --
E24 -- -- --
E25 -- -- --
E26 -- -- --
E27 -- -- --
E28 -- -- --
E29 -- -- --
E30 -- -- --
E31 -- -- --
E32 -- -- --
-- : not present

area external
LEDs (blinking NO. OF WORD NAME OF WORD
light)
For details concerning status words, see Page 37-30.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
Command This area consists of up to 2 words (numbered from 0 to 1).

area internal
red LEDs WORD NUMBER NAME OF WORD
(fixed light) 0 WORD COMMANDING RED LEDS
1 WORD COMMANDING RED LEDS
Table 37.31: Meaning of Bits of Word Commanding internal red LEDs (fixed light)
MEANING OF BIT
BIT NUMBER 50 60 150 160 170 190 300 310 320 330
W W W W W W W W
0 -- -- -- -- F1 F1 F1 F1 F1 --
1 -- -- -- -- F2 F2 F2 F2 F2 --
2 -- -- -- -- F3 F3 F3 F3 F3 --
3 -- -- -- -- F4 F4 F4 F4 F4 --
4 -- -- -- -- F5 F5 F5 F5 F5 --
5 -- -- -- -- F6 F6 F6 F6 F6 --
6 -- -- -- -- F7 F7 F7 F7 F7 --
7 -- -- -- -- F8 F8 F8 F8 F8 --
8 -- -- -- -- F9 F9 F9 F9 F9 --
9 -- -- -- -- F10 F10 F10 F10 F10 --
10 -- -- -- -- F11 F11 F11 F11 F11 --
11 -- -- -- -- F12 F12 F12 -- F12 --
12 -- -- -- -- -- F13 F13 -- F13 --
13 -- -- -- -- -- F14 F14 -- F14 --
14 -- -- -- -- -- F15 F15 -- F15 --
15 -- -- -- -- -- F16 F16 -- F16 --
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-33
Table 37.32: Meaning of Bits of Word Commanding internal red LEDs (fixed light)
MEANING OF BIT
BIT NUMBER 50 60 150 160 170 190 300 310 320 330
W W W W W W W W
0 -- -- -- -- -- F17 F17 -- F17 --
1 -- -- -- -- -- F18 F18 -- F18 --
2 -- -- -- -- -- F19 F19 -- -- --
3 -- -- -- -- -- F20 F20 -- -- --
4 -- -- -- -- -- F21 F21 -- -- --
5 -- -- -- -- -- F22 F22 -- -- --
6 -- -- -- -- -- -- -- -- -- --
7 -- -- -- -- -- -- -- -- -- --
8 -- -- -- -- -- -- -- -- -- --
9 -- -- -- -- -- -- -- -- -- --
10 -- -- -- -- -- -- -- -- -- --
11 -- -- -- -- -- -- -- -- -- --
12 -- -- -- -- -- -- -- -- -- --
13 -- -- -- -- -- -- -- -- -- --
14 -- -- -- -- -- -- -- -- -- --
15 -- -- -- -- -- -- -- -- -- --
-- : not present

area internal
red LEDs NO. OF WORD NAME OF WORD
(blinking light) 0 WORD COMMANDING RED LEDS
1 WORD COMMANDING RED LEDS
For details concerning status words, see Pages 22-28.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37

area internal
green LEDs NO. OF WORD NAME OF WORD
(fixed light)
0 WORD COMMANDING GREEN LEDS
Table 37.33: Meaning of Bits of Word Commanding internal green LEDs (fixed light)
MEANING OF BIT
BIT NUMBER 50 60 150 160 170 190 300 310 320 330
W W W W W W W W
0 -- -- F1 F1 F1 F1 F1 F1 F1 --
1 -- -- F2 F2 F2 F2 F2 F2 F2 --
2 -- -- F3 F3 F3 F3 F3 F3 F3 --
3 -- -- F4 F4 F4 F4 F4 F4 F4 --
4 -- -- F5 F5 F5 F5 F5 F5 F5 --
5 -- -- -- -- F6 F6 F6 F6 F6 --
6 -- -- -- -- F7 F7 F7 F7 F7 --
7 -- -- -- -- F8 F8 F8 F8 F8 --
8 -- -- -- -- F9 F9 F9 F9 F9 --
9 -- -- -- -- F10 F10 F10 F10 F10 --
10 -- -- -- -- F11 F11 F11 F11 F11 --
11 -- -- -- -- F12 F12 F12 F12 F12 --
12 -- -- -- -- -- F13 F13 F13 F13 F13
13 -- -- -- -- -- F14 F14 F14 F14 F14
14 -- -- -- -- -- F15 F15 F15 F15 F15
15 -- -- -- -- -- F16 F16 F16 F16 F16
-- : not present
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-35
Table 37.34: Meaning of Bits of Word Commanding internal green LEDs (fixed light)
MEANING OF BIT
BIT NUMBER 50 60 150 160 170 190 300 310 320 330
W W W W W W W W
0 -- -- -- -- -- F17 F17 F17 F17 F17
1 -- -- -- -- -- F18 F18 F18 F18 F18
2 -- -- -- -- -- F19 F19 F19 F19 F19
3 -- -- -- -- -- F20 F20 F20 F20 F20
4 -- -- -- -- -- F21 F21 F21 F21 F21
5 -- -- -- -- -- F22 F22 -- F22 F22
6 -- -- -- -- -- F23 F23 -- F23 F23
7 -- -- -- -- -- F24 F24 -- F24 F24
8 -- -- -- -- -- -- -- -- F25 F25
9 -- -- -- -- -- -- -- -- F26 F26
10 -- -- -- -- -- -- -- -- F27 F27
11 -- -- -- -- -- -- -- -- F28 F28
12 -- -- -- -- -- -- -- -- -- --
13 -- -- -- -- -- -- -- -- -- --
14 -- -- -- -- -- -- -- -- -- --
15 -- -- -- -- -- -- -- -- -- --
-- : not present

area internal
green LEDs NO. OF WORD NAME OF WORD
(blinking light)
For details concerning status words, see Page 37-34.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37

area
0 COMMAND
1 PARAMETER 1
2 PARAMETER 2
3 PARAMETER 3
Table 37.35: List of commands available (Part 1 of 4)

VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT VT
COMMAND PARAMS.
DESCRIPTION 50 60 150 160 170 190 300 310 320 330 155 185 505 505 515 525 525 555 56x 575 580 585 585 595
CODE 1 2 3 W W W W W W W W W W H W W H W W W W W W WB W
Forces
01 -- sequence -- -- -- -- -- -- -- -- -- -- -- -- -- --
02 -- -- Forces page
Forces cur-
03 -- -- --
rent field
-- -- -- -- -- -- -- -- -- -- -- -- -- --
Bit-structured
04 -- -- -- protection
mask
Forces sys-
05 -- -- --
tem context

Sets auto-
06 -- -- -- scroll for mes- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
sages
Sets current
07 -- -- --
language

Priority of
08 -- -- --
messages
-- -- -- -- -- -- -- -- -- -- -- -- --
Operation of
09 -- -- --
messages

Sets auto-
scroll time for
10 -- -- --
information

messages
Sets auto-
11 -- -- -- scroll time for -- -- -- -- -- --
ISA alarms
-- : not present r : response
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-37

COMMAND PARAMS.
DESCRIPTION 50 60 150 160 170 190 300 310 320 330 155 185 505 505 515 525 525 555 56x 575 580 585 585 595
Sets maximum
time after
12 -- -- --
which the lamp
-- -- -- -- -- -- -- -- --
switches off
Sets the maxi-

mum idle time
13 -- -- --
for keys in edit
-- -- -- --
mode
Reads current
14 r -- -- --
time
-- -- -- --
Reads current
15 r -- -- --
date
-- -- -- --
16 -- -- -- Sets the clock -- -- -- --
Sets current
17 -- -- --
date
-- -- -- --
Reads trend
18 -- -- -- from device -- -- -- -- -- -- -- -- -- -- -- --
buffer
Emptying
19 -- -- -- -- alarm history -- -- -- -- -- --
buffer
Synchroniza-
20 -- -- tion of recipe -- -- -- --
transfer
Request for a
21 -- -- recipe -- -- -- --
Send recipe to
22 -- -- VT without -- -- -- --
overwriting
Send recipe to
23 -- -- VT overwriting -- -- -- --
Command:
24 -- -- internal green -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
LEDs
Command:
flashing of
25 -- -- internal green -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
LEDs
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37

COMMAND PARAMS.
DESCRIPTION 50 60 150 160 170 190 300 310 320 330 155 185 505 505 515 525 525 555 56x 575 580 585 585 595
Command:
26 -- -- read and write -- -- -- -- -- -- -- -- -- -- -- --
pipeline
Deletes trend
27 -- -- --
from VT buffer
-- -- -- -- -- -- -- -- -- -- -- --
Reads trend
28 -- -- --
on command
-- -- -- -- -- -- -- -- -- -- -- --
29 -- -- Stop trend -- -- -- -- -- -- -- -- -- -- -- --
30 -- -- Start trend -- -- -- -- -- -- -- -- -- -- -- --
Command:
31 -- -- internal red -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
LEDs
Command:
flashing of
32 -- -- internal red -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
LEDs
Command:
33 -- -- external LEDs -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
Command:
34 -- -- flashing of -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
external LEDs
Report print-
35 -- -- --
ing
-- -- -- -- -- -- --
Printing of the
36 -- -- ISA alarms -- -- -- -- -- -- --
history buffer
37 -- -- -- Hardcopy -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
38 -- -- -- Form-feed -- -- -- -- -- -- --
Zeroes num-
39 -- -- -- ber of print -- -- -- -- -- -- --
pages
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-39

COMMAND PARAMS.
DESCRIPTION 50 60 150 160 170 190 300 310 320 330 155 185 505 505 515 525 525 555 56x 575 580 585 585 595
Command
makes internal
40 -- -- green LEDs -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
light up flashing
Command
makes inter-
41 -- -- nal red LEDs -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
light up flash-
ing
Command
makes exter-
42 -- -- nal LEDs light -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
up flashing
Acknowledg-
ment of all
43 -- -- -- --
alarms
-- -- -- -- -- --
together
Force transfer
44 -- -- mode -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
Saving the
alarm history
45 -- -- -- --
buffer and
-- -- -- -- -- -- -- -- -- -- -- -- -- -- --
trend buffers
Command for
operating
46 -- -- -- --
working of
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
touch screen
Copy recipes
48 -- -- -- -- into the rema- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
nent memory
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
We list below the commands in detail; unless otherwise indicated all the
parameter values are expressed in binary.
COMMAND 01: Forces sequence

Word Value/Meaning
0 1
Sequence identifier
1 Indicates the number of the sequence that must be displayed. If the value is zero the current sequence
is restored; this serves to quit a system page and restore the project page context.
Page identifier
2 Indicates the page number of the sequence that must be displayed. If the value is zero or a value that
is not valid, the first page of the sequence is displayed.
Page control
The parameter has 2 identifiers, one for each byte.
The high byte (more significant) contains the CURRENT FIELD, that is, the field in the page on which
3 the cursor must be positioned. If the value is zero or a value that is not valid, the current field is the first
in the page.
The low byte (less significant) contains the BIT-STRUCTURED PROTECTION MASK to be used to
protect the fields.
COMMAND 02: Forces page

Word Value/Meaning
0 2
Page identifier
1 Indicates the page number of the sequence that must be displayed. If the value is zero or a value that
is not valid, the first page of the sequence is displayed.
Page control
in the page.
protect the fields.
3 Not used
COMMAND 03: Forces current field

Word Value/Meaning
0 3
Page control
in the page.
protect the fields.
2 Not used
3 Not used
COMMAND 04: Forces bit-structured protection mask

Word Value/Meaning
0 4
Bit-structured mask
1 Uses the 8 bits of the low byte (least significant).
logic state 1 activates the protection that stops the field being varied.
2 Not used
3 Not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-41
COMMAND 05: Forces system context

Word Value/Meaning
0 5
Context identifier
Indicates which context to set.
Possible contexts are:
VT50/60
0 INFORMATION MESSAGES
1 SEQUENCE DIRECTORY
2 DRIVER
3 HELP FOR PROJECT PAGES
4 PROJECT INFORMATION
VT150/160/170/190/300/310/320/330/155/185/505/515//525/555/56x/575/580/585/585B/595
0 INFORMATION MESSAGES
1 1 SEQUENCE DIRECTORY (PAGES*)

2 DRIVER
3 HELP FOR PROJECT PAGES
4 HELP FOR ISA ALARMS
5 ISA ALARMS
6 RECIPE DIRECTORY
7 HELP FOR INFORMATION MESSASGES
8 ALARM HISTORY
9 PROJECT INFORMATION
10 SET CLOCK
11 SYSTEM MESSAGES ASSIGNED TO RECIPES
12 SYSTEM MESSAGES ASSIGNED TO PASSWORDS
2 Not used
3 Not used
(*) Only in the case of Touch Screen
COMMAND 06: Sets autoscroll for messages

Word Value/Meaning
0 6
Setting autoscroll
1 Logic state 1 or other than zero activates the function.
Logic state 0 deactivates the function.
2 Not used
3 Not used
COMMAND 07: Sets current language

Word Value/Meaning
0 7
Language identifier
1
The number of the new current language depends on the way the project is set.
2 Not used
3 Not used
COMMAND 08: Set the priority for messages

Word Value/Meaning
0 8
Setting priority for messages
1 Logic state 1 or other than zero activates the function.
Logic state 0 deactivates the function.
2 Not used
3 Not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
COMMAND 09: Operation of messages

Word Value/Meaning
0 9
Bit command
Contains activation/deactivation bits of functions as described below:
VT50/60
0 OFF/ON INFORMATION MESSAGE AUTOSCROLL
1 OFF/ON PRIORITY TO INFORMATION MESSAGES
VT150/160
0 --
1 --
2 OFF/ON BUZZER WHEN KEY IS PRESSED
3 --
1 4 OFF/ON CONTINUOUS BUZZER
6 OFF/ON PRIORITY TO DISPLAY OF INFORMATION MESSAGES
7 OFF/ON INTERMITTENT BUZZER IN PRESENCE OF INFORMATION MESSAGE
VT170/190/300/310/320/330/155/185/505/515/525/555/56x/575/580/585/585B/595
0 OFF/ON ISA ALARMS AUTOSCROLL
1 OFF/ON PRIORITY TO DISPLAY OF ISA ALARMS
2 OFF/ON BUZZER WHEN KEY IS PRESSED (AT A TOUCH*)
3 OFF/ON INTERMITTENT BUZZER IN PRESENCE OF INFORMATION MESSAGE
4 OFF/ON CONTINUOUS BUZZER
2 --
3 --
(*) Only in the case of Touch Screen
COMMAND 10: Set time for autoscroll of INFORMATION MESSAGES

Word Value/Meaning
0 10
Time of autoscroll
1
Value in secs. (1-60) indicating time to elapse before display of next INFORMATION MESSAGE page.
2 Not used
3 Not used
COMMAND 11: Set time for autoscroll of alarm messages

Word Value/Meaning
0 11
Time of autoscroll
1
Value in secs. (1-60) indicating time to elapse before display of next ALARM MESSAGE page.
2 Not used
3 Not used
COMMAND 12: Set time for after which lamp switches off
Word Value/Meaning
12
Makes it possible to set the idle time of the terminal after which the display lamp switches off. By idle
0
time we mean no pressing of the keys for a certain time. In the case of touch screens, it means no
pressing of touch screen buttons/keys.
Waiting time
1 Value in minutes (1-30) indicating the time to pass before the display lamp goes off; the value 0 deacti-
vates the function.
2 Not used
3 Not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-43
COMMAND 13: Set idle time-out for keys in edit mode

Word Value/Meaning
13
0
Sets the time after which you pass automatically from edit to display mode following the last key-touch.
Idle time
1 Value in minutes from 1 to 30
A value equal to zero disables this function.
2 Not used
3 Not used
COMMAND 14: Reads current time

Word Value/Meaning
14
0
Copies time read by internal clock into response function area.
1 Not used
2 Not used
3 Not used
COMMAND 15: Reads current date

Word Value/Meaning
0 15
1 Not used
2 Not used
3 Not used
COMMAND 16: Sets current time

Word Value/Meaning
16
0
Updates terminal clock with values sent by device.
1 HH -> Hours in BCD MM -> Minutes in BCD
2 SS -> Seconds in BCD Not used
3 Not used
COMMAND 17: Sets current date

Word Value/Meaning
0 17
1 GG -> Day in BCD MMM -> Month in BCD
2 AAAA -> Year in BCD
3 DOW -> Day of the week (0=Sunday) Not Used
COMMAND 18 : Read trend from device buffer

Word Value/Meaning
18
0
Acquires the samples in the buffer of the device as a block.
1 Number of the buffer
2 Not used
3 Not used
COMMAND 19: Empty ISA alarms history buffer

Word Value/Meaning
19
0
Makes it possible to eliminate all records of ISA alarms from history buffer.
1 Not used
2 Not used
3 Not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
COMMAND 20: Synchronization of recipe transfer

Word Value/Meaning
20
0 Makes it possible to tell the device that a recipe transfer is to start.
The device must respond to the VT before transmission can begin.
Bit commands
Contains the response bits to the RECIPE STATUS AREA
1 13 TIMEOUT confirms to the VT timeout of transmission
14 ENDTX confirms to the VT end of transmission
15 STARTTX confirms to the VT beginning of transmission
2 Not used
3 Not used
COMMAND 21: Request for a recipe

Word Value/Meaning
21
Sends the VT request to transfer a recipe to its memory.
Parameters 1 and 2 contain the 4-character code (name) of the recipe.
0 Logic state 0 of bit 4 of VT STATUS word (in VT STATUS AREA) indicates that the code requested is
present in the data memory of the VT, while logic state 1 indicates the absence of the code.
With the code present transmission starts in SYNCHRONIZED or UNSYNCHRONIZED mode as deter-
mined by the project.
1 Character 1 Character 2
3 Not Used
Device VT Video VT Data

Buffer Memory
COMMAND 22: Sends recipe to VT without overwriting

Word Value/Meaning
22
Makes it possible to send the VT a recipe with a new code for it to be saved in the data memory only if
code is absent.
0 Parameters 1 and 2 contain the 4-character code (name) of the recipe.
Logic state 0 of bit 4 of VT STATUS word (in VT STATUS AREA) indicates that the code requested is
present in the data memory of the VT, while logic state 1 indicates the absence of the code.
With the code absent the VT starts transmitting and then saving the data.
3 Not Used
The recipe code in the VT must be 4 characters long
You are advised to use this command associated with command 48

(valid for VT575W, VT580W, VT585WB, VT595W) otherwise the
recipes will be lost when the VT is switched off.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-45
COMMAND 23: Sends recipe to the VT by overwriting

Word Value/Meaning
23
Makes it possible to send the VT a recipe with a news code to save it in the data memory without
0 checking the existence of the code.Parameters 1 and 2 contain the 4-character code (name) of the rec-
ipe. Logic state 0 of bit 4 of VT STATUS word (in VT STATUS AREA) indicates that the command
was carried out correctly, while logic state 1 indicates an incorrect command.
3 Not Used
The recipe code in the VT must be 4 characters long

(valid for VT575W, VT580W, VT585WB, VT595W) otherwise the
recipes will be lost when the VT is switched off.
COMMAND 24: Command: internal green LEDs

Word Value/Meaning
24
0 Makes it possible to switch on and off the green LEDs internal to the VT and corresponding to the bits
of the words of parameters 1 and 2.
TYPE of VT
BIT
150 160 170 190 300 310 320 330
0 F1 F1 F1 F1 F1 F1 F1 --
1 F2 F2 F2 F2 F2 F2 F2 --
2 F3 F3 F3 F3 F3 F3 F3 --
3 F4 F4 F4 F4 F4 F4 F4 --
4 F5 F5 F5 F5 F5 F5 F5 --
5 -- -- F6 F6 F6 F6 F6 --
6 -- -- F7 F7 F7 F7 F7 --
1
7 -- -- F8 F8 F8 F8 F8 --
8 -- -- F9 F9 F9 F9 F9 --
9 -- -- F10 F10 F10 F10 F10 --
10 -- -- F11 F11 F11 F11 F11 --
11 -- -- F12 F12 F12 F12 F12 --
12 -- -- -- F13 F13 F13 F13 F13
13 -- -- -- F14 F14 F14 F14 F14
14 -- -- -- F15 F15 F15 F15 F15
15 -- -- -- F16 F16 F16 F16 F16
TYPE of VT
BIT
150 160 170 190 300 310 320 330
0 -- -- -- F17 F17 F17 F17 F17
1 -- -- -- F18 F18 F18 F18 F18
2 -- -- -- F19 F19 F19 F19 F19
3 -- -- -- F20 F20 F20 F20 F20
4 -- -- -- F21 F21 F21 F21 F21
5 -- -- -- F22 F22 -- F22 F22
6 -- -- -- F23 F23 -- F23 F23
2
7 -- -- -- F24 F24 -- F24 F24
8 -- -- -- -- -- -- F25 F25
9 -- -- -- -- -- -- F26 F26
10 -- -- -- -- -- -- F27 F27
11 -- -- -- -- -- -- F28 F28
12 -- -- -- -- -- -- -- --
13 -- -- -- -- -- -- -- --
14 -- -- -- -- -- -- -- --
15 -- -- -- -- -- -- -- --
3 Not Used
-- : not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
COMMAND 25: Command: flashing internal green LEDs

Word Value/Meaning
25
Makes it possible to activate or deactivate the flashing of the green LEDs internal to VT and corre-
0
sponding to the bits of the words of parameters 1 and 2.
The LED must previously have been switched on using the command 24
TYPE of VT
BIT
150 160 170 190 300 310 320 330
0 F1 F1 F1 F1 F1 F1 F1 --
1 F2 F2 F2 F2 F2 F2 F2 --
2 F3 F3 F3 F3 F3 F3 F3 --
3 F4 F4 F4 F4 F4 F4 F4 --
4 F5 F5 F5 F5 F5 F5 F5 --
5 -- -- F6 F6 F6 F6 F6 --
6 -- -- F7 F7 F7 F7 F7 --
1
7 -- -- F8 F8 F8 F8 F8 --
8 -- -- F9 F9 F9 F9 F9 --
9 -- -- F10 F10 F10 F10 F10 --
10 -- -- F11 F11 F11 F11 F11 --
11 -- -- F12 F12 F12 F12 F12 --
12 -- -- -- F13 F13 F13 F13 F13
13 -- -- -- F14 F14 F14 F14 F14
14 -- -- -- F15 F15 F15 F15 F15
15 -- -- -- F16 F16 F16 F16 F16
TYPE of VT
BIT
150 160 170 190 300 310 320 330
0 -- -- -- F17 F17 F17 F17 F17
1 -- -- -- F18 F18 F18 F18 F18
2 -- -- -- F19 F19 F19 F19 F19
3 -- -- -- F20 F20 F20 F20 F20
4 -- -- -- F21 F21 F21 F21 F21
5 -- -- -- F22 F22 -- F22 F22
6 -- -- -- F23 F23 -- F23 F23
2
7 -- -- -- F24 F24 -- F24 F24
8 -- -- -- -- -- -- F25 F25
9 -- -- -- -- -- -- F26 F26
10 -- -- -- -- -- -- F27 F27
11 -- -- -- -- -- -- F28 F28
12 -- -- -- -- -- -- F17 --
13 -- -- -- -- -- -- F18 --
14 -- -- -- -- -- -- F19 --
15 -- -- -- -- -- -- F20 --
3 Not Used
-- : not used
COMMAND 26 : Read and write pipeline

Word Value/Meaning
26
0
Reads and writes the pipeline specified.
1 Number of the pipeline
2 Not used
3 Not used
COMMAND 27 : Delete trend from VT buffer

Word Value/Meaning
27
0
Deletes the readings in the VT buffer.
2 Not used
3 Not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-47
COMMAND 28 : Read trend on command

Word Value/Meaning
28
0
With each command sent acquires a reading from the buffer of the device.
2 Not used
3 Not used
COMMAND 29 : Stop trend

Word Value/Meaning
29
0 Stops the reading of the channel corresponding to the trend buffer defined in parameter 1. The com-
mand only applies to trends in Single Automatic Sampling mode.
1 Buffer number
2 Not used
3 Not used
COMMAND 30 : Start trend

Word Value/Meaning
30
0 Starts the reading of the channel corresponding to the trend buffer defined in parameter 1. The com-
mand only applies to trends in Single Automatic Sampling mode.
1 Buffer number
2 Not used
3 Not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
COMMAND 31: Command: internal red LEDs

Word Value/Meaning
31
0 Makes it possible to switch on and off the red LEDs internal to the VT and corresponding to the bits of
the words of parameters 1 and 2.
TYPE of VT
BIT
170 190 300 310 320 330
0 F1 F1 F1 F1 F1 --
1 F2 F2 F2 F2 F2 --
2 F3 F3 F3 F3 F3 --
3 F4 F4 F4 F4 F4 --
4 F5 F5 F5 F5 F5 --
5 F6 F6 F6 F6 F6 --
6 F7 F7 F7 F7 F7 --
1
7 F8 F8 F8 F8 F8 --
8 F9 F9 F9 F9 F9 --
9 F10 F10 F10 F10 F10 --
10 F11 F11 F11 F11 F11 --
11 F12 F12 F12 -- F12 --
12 -- F13 F13 -- F13 --
13 -- F14 F14 -- F14 --
14 -- F15 F15 -- F15 --
15 -- F16 F16 -- F16 --
TYPE of VT
BIT
170 190 300 310 320 330
0 -- F17 F17 -- F17 --
1 -- F18 F18 -- F18 --
2 -- F19 F19 -- -- --
3 -- F20 F20 -- -- --
4 -- F21 F21 -- -- --
5 -- F22 F22 -- -- --
6 -- -- -- -- --
2
7 -- -- -- -- --
8 -- -- -- -- -- --
9 -- -- -- -- -- --
10 -- -- -- -- -- --
11 -- -- -- -- -- --
12 -- -- -- -- -- --
13 -- -- -- -- -- --
14 -- -- -- -- -- --
15 -- -- -- -- -- --
3 Not Used
-- : not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-49
COMMAND 32: Command: flashing of internal red LEDs

Word Value/Meaning
32
Makes it possible to activate or deactivate the flashing of the red LEDs internal to VT and correspond-
0
ing to the bits of the words of parameters 1 and 2.
TYPE of VT
BIT
170 190 300 310 320 330
0 F1 F1 F1 F1 F1 --
1 F2 F2 F2 F2 F2 --
2 F3 F3 F3 F3 F3 --
3 F4 F4 F4 F4 F4 --
4 F5 F5 F5 F5 F5 --
5 F6 F6 F6 F6 F6 --
6 F7 F7 F7 F7 F7 --
1
7 F8 F8 F8 F8 F8 --
8 F9 F9 F9 F9 F9 --
9 F10 F10 F10 F10 F10 --
10 F11 F11 F11 F11 F11 --
11 F12 F12 F12 -- F12 --
12 -- F13 F13 -- F13 --
13 -- F14 F14 -- F14 --
14 -- F15 F15 -- F15 --
15 -- F16 F16 -- F16 --
TYPE of VT
BIT
170 190 300 310 320 330
0 -- F17 F17 -- F17 --
1 -- F18 F18 -- F18 --
2 -- F19 F19 -- -- --
3 -- F20 F20 -- -- --
4 -- F21 F21 -- -- --
5 -- F22 F22 -- -- --
6 -- -- -- -- --
2
7 -- -- -- -- --
8 -- -- -- -- -- --
9 -- -- -- -- -- --
10 -- -- -- -- -- --
11 -- -- -- -- -- --
12 -- -- -- -- -- --
13 -- -- -- -- -- --
14 -- -- -- -- -- --
15 -- -- -- -- -- --
3 Not Used
-- : Not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
COMAND 33 : Command: external LEDs

Word Value/Meaning
33
0 Makes it possible to switch on and off the LEDs external to the VT and corresponding to the bits of the
words of parameters 1 and 2.
TYPE of VT
BIT 150 300-310-320

+ 160 +
VT100MT1000 VT100MT1000
0 E1 E1 E1
1 E2 E2 E2
2 E3 E3 E3
3 E4 E4 E4
4 E5 E5 E5
5 E6 E6 E6
1 6 E7 E7 E7
7 E8 E8 E8
8 E9 E9 E9
9 E10 E10 E10
10 E11 E11 E11
11 E12 E12 E12
12 E13 E13 E13
13 E14 E14 E14
14 E15 E15 E15
15 E16 E16 E16
TYPE of VT
BIT 150 300-310-320

+ 160 +
VT100MT1000 VT100MT1000
0 E17 E17 E17
1 E18 E18 E18
2 E19 -- E19
3 E20 -- E20
4 -- -- --
5 -- -- --
2 6 -- -- --
7 -- -- --
8 -- -- --
9 -- -- --
10 -- -- --
11 -- -- --
12 -- -- --
13 -- -- --
14 -- -- --
15 -- -- --
3 Not Used
-- : not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-51
COMMAND 34: Command: flashing of external LEDs

Word Value/Meaning
34
Makes it possible to activate or deactivate the LEDs internal to VT and corresponding to the bits of the
0
words of parameters 1 and 2.
TYPE of VT
BIT 150 300-310-320

+ 160 +
VT100MT1000 VT100MT1000
0 E1 E1 E1
1 E2 E2 E2
2 E3 E3 E3
3 E4 E4 E4
4 E5 E5 E5
5 E6 E6 E6
1 6 E7 E7 E7
7 E8 E8 E8
8 E9 E9 E9
9 E10 E10 E10
10 E11 E11 E11
11 E12 E12 E12
12 E13 E13 E13
13 E14 E14 E14
14 E15 E15 E15
15 E16 E16 E16
TYPE of VT
BIT 150 300-310-320

+ 160 +
VT100MT1000 VT100MT1000
0 E17 E17 E17
1 E18 E18 E18
2 E19 -- E19
3 E20 -- E20
4 -- -- --
5 -- -- --
2 6 -- -- --
7 -- -- --
8 -- -- --
9 -- -- --
10 -- -- --
11 -- -- --
12 -- -- --
13 -- -- --
14 -- -- --
15 -- -- --
3 Not Used
-- : not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
COMMAND 35: Prints report

Word Value/Meaning
35
0
Makes it possible to print the report indicated numerically in parameter 1.
1 Number of the report to print
2 Not used
3 Not used
COMMAND 36: Print ISA alarms history buffer

Word Value/Meaning
36
0
Makes it possible to print the ISA alarm message history buffer
1 Not used
2 Not used
3 Not used
COMMAND 37: Hardcopy

Word Value/Meaning
37
0
Makes it possible to reproduce the page being displayed on the printer
Print mode
1
0 TEXT MODE
2 Not used
3 Not used
COMMAND 38: Form-Feed

Word Value/Meaning
38
0
Makes it possible to send the printer the command feed the sheet.
Choice of VT port for communication with printer
1 0 ASP
15 LPT
2 Not used
3 Not used
COMMAND 39: Reset print sheet counter to zero

Word Value/Meaning
39
0
Makes it possible to reset print sheet counter to zero and therefore start from sheet 1 again.
1 Not used
2 Not used
3 Not used
COMMAND 40 : Command makes internal green LEDs light up flashing

Word Value/Meaning
40
0 Lights up internal green VT LEDs corresponding to the bits of the words of parameters 1 and 2, unit-
ing in a single command both commands 24 and 25.
1 See Command 24 or 25
3 Not used
COMMAND 41 : Command makes internal red LEDs light up flashing

Word Value/Meaning
41
0 Lights up red internal VT LEDs corresponding to the bits of the words of parameters 1 and 2, uniting in
a single command both commands 31 and 32.
1 See Command 31 o 32
2 See Command 31 o 32
3 Not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

37-53
COMMAND 42 : Command makes internal LEDs light up flashing

Word Value/Meaning
42
0 Lights up internal VT LEDs corresponding to the bits of the words of parameters 1 and 2, uniting in a
single command both commands 33 and 34.
3 Not used
COMMAND 43 : Acknowledgement of all alarms together

Word Value/Meaning
43
0
Tacita tutti gli allarmi presenti.
1 Not used
2 Not used
3 Not used
COMMAND 44 : Force transfer mode

Word Value/Meaning
44
0 In the VT activate the transfer mode of the project (project, firmware and recipes), directly selecting the
source and the transmission speed.
Select source for transfer
Allows the selection of the source from which to receive/transmit the project.
The possible choices are:
1 0 MSP
1 ASP
2 Memory Card
Select the transmission speed
Allows the selection of the speed of transfer when the source selected is MSP or ASP; this parameter
is not considered with other sources.
The possible choices are:
0 300 bit/sec
1 600 bit/sec
2 1200 bit/sec
2 3 2400 bit/sec
4 4800 bit/sec
5 9600 bit/sec
6 19200 bit/sec
7 38400 bit/sec
8 57600 bit/sec
9 115200 bit/sec
3 Not used
COMMAND 45 : Saving the alarm history buffer and/or trend buffers

Word Value/Meaning
45
0 Makes it possible to save all the ISA alarm registrations from the history buffer and/or save all trend
buffers permanently.
1 Not used
2 Not used
3 Not used
COMMAND 46 : Command for operating working of touch screen

Word Value/Meaning
46
0 With this the touch screen can be activated or deactivated. When the touch screen is deactivated pres-
sure on the glass remains withoout effect.
Select operation
The choices possible are:
1
0 Not active (no pressure detected)
1 Active
2 Not used
3 Not used
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 37
COMMAND 48 : Copy recipes into the remanent memory

Word Value/Meaning
48
0
This allows all the recipes in the volatile memory to be copied into the remanent memory (Flash).
1 Not used
2 Not used
3 Not used

and/or 23 otherwise the recipes will be lost when the VT is
switched off.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

38-1
Chapter 38 Communication protocols
Contents Page
List of protocols 38-2

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 38
38-2 Communication protocols
Our VT terminals can be connected to most devices on the market, thanks

to specially designed communication protocols that act as an interface
between the VT and the Device.
List of A list exists showing which devices the VT can communicate with and
protocols including further technical information that may be useful to the program-
mer.
This list is included on the cd-rom VTWIN KIT.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

39-1
Chapter 39 Free terminal protocol
Contents Page
Free terminal protocol 39-2
Editing parameters for VT50 39-3
Editing parameters for VT60 39-4
Editing parameters for VT150/160W 39-5
Free terminal control characters 39-6
Key codes for VT50 39-9
Key codes for VT60 39-9
Key codes for VT150/160W 39-10
Code of External keys for MT1000 and VT160W 39-13
Free terminal in Network 39-14
Example of handling 39-16

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 39
39-2 Free terminal protocol
Our VT terminals can be connected with the majority of devices on the

market, but, given the considerable number and variety of these devices, it
may happen that one is incompatible. To meet the needs of those using an
incompatible device, we have created a special driver called Free terminal.
Free terminal The operator terminal has a type of driver called Free terminal that makes
protocol it possible to communicate with any type of intelligent device not supported
by the standard drivers supplied. This driver requires that the device man-
age the VT terminal in all its functions; this happens by sending control
characters that the VT interprets and then sending characters to be dis-
played. When a is pressed, the VT sends the device the value of that
such that the device recognizes and, if necessary, uses it.
The free terminal protocol also allows you to create a network of up to 31

terminals (01 -> 31); the connection must be made using serial RS485 (see
Chapter 34 -> Network connection).
To transfer the driver to the VT, the terminal must be set up for reception
(see Setting up for reception of the various terminals) before proceeding
to transfer (see Software Manual).
Once the transfer has been completed the VT displays the following page
VT-50 TERMINAL Vx.xx
All the examples quoted in this chapter refer to VT50.
This means that the transfer has been effected properly and that the VT is
ready to communicate with the device.
The transfer of the free terminal automatically sets the serial communica-
tion parameters with pre-established values:
VT address -> 00
Speed -> 9600 Baud
Parity -> N
Data bits -> 8
Stop bits -> 2
The above page remains in vision so long as the device connected does not
command it to be canceled and takes over control. The connecting cable is
the same as that used for the transfer (see Chapter 30 -> PC <-> VT con-
nection).
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

39-3
F1 F5
Esc
Editing These values can be changed by pressing + (standard protocol) or
parameters for F1 F5 Help
Esc
VT50 + + (ver.3.0 protocol); the screen shows:
Changes params.
VT Address: 00
Help Info
[Up] [Down] [Enter]
F5
Changes params.
Baud Rate: 9600
Help Info
[Up] [Down] [Enter]
F5
Changes params.
Param: PN,8db,2sb
Help Info
[Up] [Down] [Enter]
F5
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 39
F1 F4
Esc
Editing These values can be changed by pressing + Enter
(standard protocol) or
parameters for Help
F4 F1
VT60 Esc
+ Enter
+ (ver.3.0 protocol); the screen shows:
VT Address: 00
Changes params
F1 Info
[Up] [Down] [Enter]
F4
Enter
Baud Rate: 9600

Changes params
F1 Info
[Up] [Down] [Enter]
F4
Enter
Param: PN,8db,2sb
Changes params
F1 Info
[Up] [Down] [Enter]
F4
Enter

READY
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

39-5
shift
Editing These values can be changed by pressing twice (standard protocol) or
parameters for Clr PgUp
Esc
VT150/160W + Enter
+ (ver.3.0 protocol); the screen shows:
VT Address: 00
Changes params
PgUp PgDn
[Up] [Down] [Enter]
Enter
Baude Rate: 9600

Changes params
PgUp PgDn
[Up] [Down] [Enter]
Enter
Param: PN,8db,2sb
Changes params
PgUp PgDn
[Up] [Down] [Enter]
Enter
VT-xxx TERMINAL Vx.xx

READY
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 39
Free terminal The VT uses a set of characters that, sent correctly, function as a command
control and enable the VT to carry out certain operations.
characters
For the command to be recognized as such it must be preceded by the con-
trol character <ESC> and followed by the control character <EOT>.
The maximum length of a command string is 32 characters.
The tables below list the control characters to be used and the commands.
Table 39.1: Control characters of Free Terminal

Code
Character Meaning Effect
Decimal Ascii
Takes the cursor one space
<BS> 8 Back Space back on the same line, cancel-
ing the character
Takes the cursor to the begin-

<CR> 13 Carriage Return
ning of the following line
Takes the cursor to the next

<LF> 10 Line Feed line leaving it in the same
position
Signals the beginning of a

<ESC> 27 Escape
command
<EOT> 4 End Of Text Signals the end of a command
If sent several times in succession the character <EOT> can be

used to un-block the VT terminal in the event that the sending of
erroneous commands has destabilized the terminal.
Table 39.2: Command characters (Part 1 of 3)
Command Parameters Effect

Checks the connection between VT and
<ESC>Y<EOT> -- device. If the connection is right the termi-
nal replies with the string OK.
Clears display, taking the cursor to position
<ESC>C<EOT> --
0,0 (top left-hand angle).
yy = 0....Rows - 1 (0...3)
<ESC>Ayyxx<EOT> Takes the cursor to the co-ordinates yy,xx.
xx = 0....Columns - 1 (0...19)
ss = 00 ->Off Changes the status of the cursor: off/blink-
<ESC>Bss<EOT>
01 ->Blinking (Default) ing.
*If present on/in the terminal
**Applies only to VT150W and VT160W
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

39-7

dd = 00 -> Up
01 -> Right
Moves the cursor relatively with regard to
<ESC>Fddxx<EOT> 02 -> Down
the current position.
03 -> Left
xx = No. of moves
Clears display, taking the cursor to position
<ESC>Z<EOT> -- 0,0 (top left-hand angle),switch off all
LEDs* and the buzzer*.
ss = 00 ->Echo disabled
Displays the code of the key that has been
<ESC>Ess<EOT> (Default)
pressed (if above 20Hex)
01 ->Echo enabled
Re-initialize the terminal (equivalent to
<ESC>X<EOT> --
switching off and switching on again).**
bb = 00 -> 300
01 -> 600
02 -> 1200
03 -> 2400
04 -> 4800
05 -> 9600 (Default) Setting serial communication parameters.
06 -> 19200
07 -> 38400 When you use the command
<ESC>Pbbpp<EOT> to configure
08 -> 57600
the serial port with parameters dif-
09 -> 115200 ferent from the current ones, you must
pp = 00 -> EVEN, 7, 1 also reconfigure the device connected
<ESC>Pbbpp<EOT>
01 -> EVEN, 7, 2 with the same values as the VT, other-
02 -> EVEN, 8, 1 wise it will not be possible to communi-
cate. When the communication port is
03 -> EVEN, 8, 2
configured by commands rather than a
04 -> ODD, 7, 1 keyboard, this configuration does not
05 -> ODD, 7, 2 remain resident in the VT.
06 -> ODD, 8, 1
07 -> ODD, 8, 2
08 -> NONE, 7, 1
09 -> NONE, 7, 2
10 -> NONE, 8, 1
11 -> NONE, 8, 2 (Default)
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 39

xx = 01 -> F1
02 -> F2
03 -> F3
04 -> F4
05 -> F5
06 -> Info
07 -> Help
08 -> E1
09 -> E2
10 -> E3
11 -> E4
12 -> E5
13 -> E6
14 -> E7
15 -> E8
Commands the state of the LEDs associ-
<ESC>Lxxss<EOT> 16 -> E9
ated with the internal and external keys.**
17 -> E10
18 -> E11
19 -> E12
20 -> E13
21 -> E14
22 -> E15
23 -> E16
24 -> E17
25 -> E18
26 -> E19 only MT1000
27 -> E20 only MT1000
99 -> All
ss = 00 -> Off (Default)
01 -> On
02 -> Flashing
aa = 00 -> When keys are pressed
01 -> Intermittent Commands the state of the buzzer in the
<ESC>Saabb<EOT>
bb = 00 -> Disabled (Default) terminal.**
01 -> Enabled
mm = 00 -> Numeric mode
<ESC>Kmm<EOT> (Default) Setting of the keyboard operation mode.**
01 -> ASCII mode
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

39-9
Key codes for As already mentioned, when the are pressed the VT sends a hexadeci-
VT50 mal code to the connected device. The table below lists the association
between code and .
Table 39.3: Association between keys and hexadecimal codes
Hexadecimal code
Key
Only key Shift +
F1
Esc
09 14
F2
04 15
F3
02 16
F4
0B 17
F5
0D 18
Help
01 12
Info
03 10
VT60 mal code to the connected device. The table below lists the association
between code and .
Table 39.4: Association between keys and hexadecimal codes
Hexadecimal code
Key
Only key Shift +
F1
01 14
F2
03 15
F3
02 16
F4
0D 17
Enter
Help
09 12
Esc
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 39
VT150/160W mal code to the connected device. The code depends on the the mode set for
the keyboard; whether Numeric or ASCII. The former sends the code
related to the numbers on the keys; the second sends the code of the alpha-
betical characters. The default setting is Numeric, but this can be changed
by sending the command K (see Page 39-6). The table below lists the asso-
ciation between code and .
Table 39.5: Association between keys (Numeric mode) and hexadecimal codes (Part 1 of 2)
Hexadecimal code
Key
Only key shift +
F6
F1
81 86
F7
F2
82 87
F8
F3
83 88
F9
F4
84 89
F10
F5
85 8A
Info 0C 0C
Help 0B 0B
PgUp
01 05
PgDn
03 06
04 04
02 02
. 20 2E
Space
Clr
Esc
27 0A
Reinitializa-
0D
Enter tion of VT
A
B
0
30 30
C
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

39-11
Table 39.5: Association between keys (Numeric mode) and hexadecimal codes (Part 2 of 2)
Hexadecimal code
Key
Only key shift +
D
E
1
31 31
F
G
H
2
32 32
I
J
K
3
33 33
L
M
N
4
34 34
O
P
Q
5
35 35
R
S
T
6
36 36
U
V
W
7
37 37
X
Y
Z
8
38 38
-
+
/
9
39 39
=
In ASCII mode the code relating to the first, second or third letter respec-
tively is sent when the keys F1, F2, or F3 are pressed followed by the key
containing the alphanumeric characters.
Example.
S
F6
T
F1 U 6
Pressing + sends the code relating to the letter S.
Table 39.6: Association between keys (Ascii mode) and hexadecimal codes (Part 1 of 3)
Hexadecimal code
Key
F6 F7 F8
Only key shift +
F1
+
F2
+
F3
+
F6
F1
-- 86 -- -- --
F7
F2
-- 87 -- -- --
F8
F3
-- 88 -- -- --
-- : Send no code
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 39
Hexadecimal code
Key
F6 F7 F8
Only key shift +
F1
+
F2
+
F3
+
F9
F4
84 89 84 84 84
F10
F5
85 8A 85 85 85
Info 0C 0C 0C 0C 0C
Help 0B 0B 0B 0B 0B
PgUp
01 05 01 01 01
PgDn
03 06 03 03 03
04 04 04 04 04
02 02 02 02 02
. 20 2E 20 20 20
Space
Clr
Esc
27 0A 27 27 27
Reinitializa-
0D 0D 0D 0D
Enter tion of VT
A
B
0
30 30 41 42 43
C
D
E
1
31 31 44 45 46
F
G
H
2
32 32 47 48 49
I
J
K
3
33 33 4A 4B 4C
L
M
N
4
34 34 4D 4E 4F
O
P
Q
5
35 35 50 51 52
R
S
T
6
36 36 53 54 55
U
-- : Send no code
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

39-13
Hexadecimal code
Key
F6 F7 F8
Only key shift +
F1
+
F2
+
F3
+
V
W
7
37 37 56 57 58
X
Y
Z
8
38 38 59 5A 2D
-
+
/
9
39 39 2B 2F 3D
=
-- : Send no code
Code of The table below lists the association between code and .
External keys
for MT1000 Table 39.7: Association between MT1000 keys and hexadecimal codes
and VT160W Hexadecimal code
A0 A1 A2 A3
A4 A5 A6 A7
A8 A9 AA AB
AC AD AE AF
B0 B1 B2 B3
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 39
Table 39.8: Association between VT160 keys and hexadecimal codes
Hexadecimal code
A0 A1 A2 A3 A4 A5
A6 A7 A8 A9 AA AB
AC AD AE AF B0 B1
Free terminal Using the Free terminal protocol the VT can be connected in a RS485
in Network linked network to enable a master device to show information to or request
information from the various connected terminals.
Each connected terminal in this network must have been loaded with the
Free terminal protocol and must have a different network address from any
of the other addresses in the network (01 -> 31). If the address is 00, the ter-
minal is not considered to be a participant in the network.
To change the network address see Page 39-3.
Once the terminal has been connected to the network (with an address other
than 00) and switched on, the VT terminals behavior is different from that
seen in the previous paragraphs. The VT will not respond to any command
unless it has been addressed. Addressing a terminal means that from that
moment on the master device will communicate exclusively with that ter-
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

39-15
minal. Let us imagine the rotating selector with 31 positions from 0 to 31,
the position of the selector indicates which terminal to communicate with.
After being addressed, the terminal will respond to all commands, as if it

were directly connected to the device, the other will ignore any instruction
passing through the network.
Even the sending of by the VT is different: when a is pressed, its

hexadecimal code is no longer sent automatically to the device, but is stored
in a buffer (Max 64 ) that the master device must ask. These keys are
then not sent altogether but one at a time.
Help Info F1
Esc
For example, of the VT buffer contained 3 , and , then the
VT would respond to the first request with "0301" (3 in the buffer, the
first having the code 01Hex). The response to the second request would be
"0203" (2 , code 03Hex); the response to the third request would be
"0102" (1 , code 09Hex). In order to communicate that there are no keys
in its buffer, the VT will respond to any further request with "0000".
There follows a list of permissible commands.
Table 39.9: Command characters with terminal in network.

<ESC>Ixx<EOT> xx = 01....31 Addresses a terminal to communicate with
xx = Number of keys in buffer Asks VT for keys from its internal buffer.
<ESC>T<EOT>
yy = Hex. code of key sent The VTs response is xxyy in Ascii format.
kk = 00 ->Never sends any key
(Default)
01 ->Transmits the key
only when the VT is
addressed or when it
has the address 00
Modifies the mode of saving and sending
<ESC>Dkkmm<EOT> mm = 00 -> Always saves the key keys of a VT within the network.
in the VTs internal
buffer (Default)
01 ->Saves the key in the
VTs internal buffer
only when the VT is
addressed
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 39
Example of Let us suppose we have a VT50 that has to display the text GOOD
handling F5
MORNING OPERATOR centered on the display and, when is
pressed is canceled and replaced by the word READY justified top left.
There are various ways of proceeding, each leading to the same result; what
follows is just one example.
Prepare the VT50 for communication by using Free Terminal. To do this,

transfer the appropriate driver (see Page 39-2) and set the various commu-
nication parameters (see Page 39-3). Once the settings have been completed
the following page appears
First check that the VT communicates with the device. Send the following
string.
<ESC>Y<EOT>
If communication has been correctly established, the VT responds with the

following message.
<OK>
At this point the device must interpret the response and control begins.
First cancel the display. Send the following string.
<ESC>C<EOT>
The display is cleared and the cursor goes automatically to the top left cor-
ner with the 0,0 (y,x) co-ordinate.
Position the cursor at co-ordinate 0,5 (y,x). Send the following string.
<ESC>A0005<EOT>
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

39-17
Now the display looks like this:
Send the first part of the text to be displayed GOOD MORNING. Send
the following string.
GOOD MORNING
The display now shows
GOOD MORNING_
Position the cursor on the co-ordinate 1,5 (y,x). Send the following string.
<ESC>A0105<EOT>
GOOD MORNING
_
Send the rest of the text to be displayed: OPERATOR. Send the follow-
ing string.
OPERATOR
GOOD MORNING
OPERATOR_
At this point the device must be set up to control the keys when pressed;
F5
when is pressed the VT responds with the following character.
<CR>
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 39
The device must interpret and send the string for canceling the text. Send
the following string.
<ESC>C<EOT>
The display is now cleared and the cursor positioned automatically in the
top left corner with the coordinate 0,0 (y,x)
Now send the text to be displayed READY. Send the following string.
READY
READY_
The above represents only a simple example of how to use the Free Termi-
nal.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-1
Chapter 40 Connection cables
Contents Page
General notes 40-4
Connecting the cable shield 40-5
MSP<->ASP conversion 40-7
ELECTREX NETWORK ANALYZER 40-8
ABB DRIVE 40-8
ALLEN-BRADLEY DRIVE 40-9
ATLAS COPCO DRIVE 40-10
BERGER-LAHR DRIVE 40-11
CONTROL TECHNIQUES DRIVE 40-11
DANFOSS DRIVE 40-12
ELAU DRIVE 40-13
EUROTHERM DRIVE 40-14
EVER DRIVE 40-15
FANUC ROBOTICS DRIVE 40-15
FAGOR DRIVE 40-16
GALIL DRIVE 40-17
GE DRIVE 40-17
HITACHI DRIVE 40-17
KEB DRIVE 40-18
INDRAMAT DRIVE 40-19
LENZE DRIVE 40-19
OMRON DRIVE 40-21
OSAI DRIVE 40-21
PANASONIC DRIVE 40-21
PARKER AUTOMATION DRIVE 40-22
ROBOX DRIVE 40-23

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
40-2 Connection cables
Contents Page
S.B.C. DRIVE 40-24
SEW-EURODRIVE DRIVE 40-25
SIEI DRIVE 40-26
SIEMENS DRIVE 40-26
STBER DRIVE 40-27
TDE MACNO DRIVE 40-27
TELEMECANIQUE DRIVE 40-28
TRIO MOTION DRIVE 40-28
DATALOGIC BARCODE READER 40-29
ABB PLC 40-30
AEG MODICON PLC 40-33
ALLEN-BRADLEY PLC 40-34
ALTUS PLC 40-38
ATOS PLC 40-39
BECKHOFF PLC 40-40
BOSCH PLC 40-42
B&R AUTOMATION PLC 40-42
CROUZET RPX PLC 40-42
FOXBORO PLC 40-43
FUJI PLC 40-43
GE FANUC PLC 40-44
GEFRAN PLC 40-45
LG PLC 40-52
HITACHI PLC 40-46
IDEC IZUMI PLC 40-48
KLCKNER MOELLER PLC 40-49
KEYENCE PLC 40-50
KOYO PLC 40-50
KUHNKE PLC 40-52

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-3
Contents Page
MATSUSHITA-NAIS PLC 40-54
MICROLINK PLC 40-56
MITSUBISHI PLC 40-56
OMRON PLC 40-58
SAIA PLC 40-60
SATT CONTROL PLC 40-64
SCHLEICHER PLC 40-65
SIEMENS PLC 40-66
SPRECHER+SCHUH PLC 40-69
SQUARE-D PLC 40-69
TELEMECANIQUE PLC 40-70
TEXAS INSTRUMENTS PLC 40-74
TOSHIBA PLC 40-76
HBM BALANCE SCALES 40-77
ASCON THERMOREGULATOR 40-78
GEFRAN THERMOREGULATOR 40-78
HENGSTLER THERMOREGULATOR 40-79
WEST THERMOREGULATOR 40-80
Cable information summary 40-81

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
All VTs communicate with other devices using serial port communication.
In this chapter you will find information on all the cables used to connect
with various devices together with their order codes.
Those cables marked NOT CODED are not supplied by ESA

elettronica but listed here nonetheless to make it easier for the
user to make them.
General notes Serial communications are highly susceptible to disturbances, so, in order
to limit as much as possible the influence of these disturbances good quality
shielded cables must be used.
The table below lists the characteristics of the cable to be used for serial
connection.
Specifications of serial connection cable

Direct current resistance Max. 151 Ohm/Km
Capacity coupling Max. 29pF/m
Shielding > 80% or total
Particular care should be taken in the choice and lay-out of cables,

specially with regard to the VT <-> Device connection serial cable.
Always:
Find the shortest route
Lay disturbed cables separately
Disconnect the power supply before connecting or disconnecting

the communication cables so as to avoid possible damage to the
VT and/or the connected device.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-5
Connecting It is essential for the interface cables between the VT and the Device be
the cable correctly shielded in order to ensure that serial communication occurs free
shield from all types of external interference. For this reason all the cables listed in
this manual absolutely must be shielded cables and the D-sub connectors
both on the VT side and the Device side must have metal or conductive
plastic shells.
The diagram below shows the correct way of connecting the shield.
Connective shell
Braiding
Securing screw
Connective shell
NB: The braiding must

be electrically con-
nected both to the
connector body and
Connector body shell.
The interface cable braiding must be electrically connected both to the shell
and the body of the connector at both ends of the cable.
If the connection operation cannot be carried out at the Device side due to
the particular type of serial connector, the braiding will have to be taken
outside the connector and connected to the earth terminal.
This operation must also be carried out if the body of the Devices serial
connector, although of a standard type, is not electrically connected to the
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
earth terminal of the PLC itself.
Note that in this situation the shield must still be connected both to the shell
and the body of the connector.
Certain cable diagrams show the pin connections of the shield signals on
the Device side: in these cases, not only does the above apply but the shield
must also be connected to them.
In any event the shield must never be connected on the VT side (pin 1).
Earth potentials obtained from DIN guides, structural elements of

the machines, electrical cabinet doors etc. are not admissible and
it is a good idea to avoid unipotential earth bars which receive earth
connections from loads such as inverters, drives, stepper motors and,
generally speaking, any type of load which could be a source of strong
disturbance.
The Device-VT serial communication cable must be single piece.

Terminal-type joins and PLUG+SOCKET arrangements are
inadmissible. Should the installation system in question necessitate that
breaks be made (although this is inadvisable) it will be ABSOLUTELY
necessary to implement the following:
Use D-SUB (Db9, Db15 o DB25) connectors with metal or conduc-

tive plastic shells.
Connect the serial cable shield in accordance with the instructions
on this page.
Limit the number of breaks to those absolutely unavoidable.
Failure to observe these instructions could prejudice the compatibility

of the VT-PLC system with the EMC standards currently in force.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-7
MSP<->ASP The cables referred to in this chapter are designed to be connected to the
conversion MSP port of the VT terminal; if you need to use a coded on the ASP port, it
will be necessary to use the adapters listed below.
VT side Cable side Order code:

D-Sub D-Sub
15 pin male 25 pin female NOT CODED
Conversion from MSP to ASP
Rx 2 3 Rx (RS232)
Tx 3 2 Tx
(SeeChapter 40 -> Connecting the cable shield)
RTS 10 4 RTS
CTS 11 5 CTS
GND 7 7 GND
+Vcc 13 16 +Vcc
Max. 15 cm.

D-Sub D-Sub
Conversion from MSP to ASP
TxRx+ 8 22 TxRx+ (RS485)
(See Chapter 40 -> Connecting the cable shield)

TxRx- 15 10 TxRx-
RTS 10 4 RTS
CTS 11 5 CTS
GND 7 7 GND
+Vcc 13 16 +Vcc
Max. 15 cm.

D-Sub D-Sub
9 pin female 25 pin female NOT CODED
Conversion from MSP to ASP-9
Rx 2 3 Rx (RS232)
Tx 3 2 Tx
(SeeChapter 40 -> Connecting the cable shield)
RTS 7 4 RTS
CTS 8 5 CTS
GND 5 7 GND
Max. 15 cm.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
ELECTREX NETWORK ANALYZER
VT side ANALYZER side Order code:

D-Sub Terminals
25 pin male NOT CODED
DEPT-485
TxRx+ 22 A (RS485)
120 120
1/4 W 1/4 W (See Chapter 40 -> Connecting the cable shield)
TxRx- 10 B
GND 7
JUMPER SETTINGS
25
RTS 4
CTS 5 Data Format
15 IEEE
18 BCD
Dip-switch 4
ABB DRIVE
VT side Drive side Order code:

D-Sub D-Sub
25 pin male 9 pin male NOT CODED
INDAX - TRIAX - PENTAX
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
GND 7 5 GND NOTE: The length of the cable must not exceed 3 meters with a transmission
speed of 38400 Baud.
25
RTS 4 (See Chapter 40 -> Connecting the cable shield)
CTS 5
15
18

D-Sub D-Sub
TX+ 23 2 RX+ (RS422)

TX- 12 8 RX-
RX+ 13 1 TX+
220
1/4 W
RX- 24 4 TX-
25 5 GND
GND 7
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-9

D-Sub D-Sub
TxRx+ 22 2 RxTx+ (RS485)

220
1/4 W (See Chapter 40 -> Connecting the cable shield)
TxRx- 10 8 RxTx-
GND 7 5 GND
25
RTS 4
CTS 5
15
18

D-Sub D-Sub
BIVECTOR Series 300
16 1 SHD (RS485)
470
1/4 W
TxRx+ 22 9 TxRx+
220
1/4 W
TxRx- 10 8 TxRx-
470
1/4 W
GND 7 5 GND
25
RTS 4
CTS 5
15
18
ALLEN-BRADLEY DRIVE

D-Sub D-Sub
IMC S CLASS
TX+ 23 7 RXD+ (RS422)

220
1/4 W
ATTENTION!!! Valid only for MSP
TX- 12 3 RXD-
RX+ 13 4 TXD+ (See Chapter 40 -> Connecting the cable shield)
220
1/4 W
RX- 24 2 TXD-
25 5 GND
GND 7
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
IMC S CLASS
RxD 3 2 TxD (RS232)

TxD 2 3 RxD
ATTENTION!!! Valid only for MSP
GND 7 5 GND
25 (See Chapter 40 -> Connecting the cable shield)
RTS 4
CTS 5
15
18
Max. 15 m.
ATLAS COPCO DRIVE

D-Sub D-Sub
Series DMC
1 SHD (RS232)
RxD 3 3 Tx
N.B.: On the device set protocol Computer Mode with the aid of ATLAS DMC
TxD 2 2 Rx
Users manual.
GND 7 7 GND
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub D-Sub
Series DMC
1 SHD (RS422)
TX+ 23 10 RX+
220 N.B.: On the device set protocol Computer Mode with the aid of ATLAS DMC
1/4 W Users manual.
TX- 12 9 RX-
RX+ 13 12 TX+ (See Chapter 40 -> Connecting the cable shield)
220
1/4 W
RX- 24 11 TX-
25 7 GND
GND 7
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-11
BERGER-LAHR DRIVE
VT Side Drive Side Order code:

Phoenix D-Sub
Twin Line
Shild 3 Card CAN-C required

CAN+ 4 7 CAN_High
(CAN)
CAN- 2 2 CAN_Low For the VT side cable termination see Chapter 34 -> CAN: Connection.
V- 1 1 GND
For the DRIVE side cable termination see Drive manual TLC53x.
NOTE: The max. length of the cable depends on the transmission speed.
See note Trasmission speed (kbit/s) Length (m.)

100 500
1000 40
CONTROL TECHNIQUES DRIVE

D-Sub D-Sub
Unidrive
RxD 3 3 TxD (RS232)

TxD 2 2 RxD
Communication card UD71 required
GND 7 5 GND
25 Set parameter 0.32 = ANSI2
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub D-Sub
Unidrive
16 1 (RS485)
470 6
1/4 W
Communication card UD71 or UD70 required
TxRx+ 22 7
220
1/4 W UD71:
TxRx- 10 2 Set parameter 0.32 = ANSI2
470
3
1/4 W UD70:
GND 7 Set parameter 17.06 = 5 (ANSI2)
25 Set parameter 17.05 = (Serial address)
RTS 4
Set parameter 17.07 = (Baud rate)
CTS 5 (See Chapter 40 -> Connecting the cable shield)

15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub RJ45
25 pin male 8 pin CVPLC33102
Commander SE - CTNET
SHD
VCC 16 (RS485)
470
1/4 W
Set parameter 41 = ANSI
TxRx+ 22 2 RxTx
220 Set parameter 42 = (Baud rate)
1/4 W Set parameter 43 = (Address)
TxRx- 10 7 RxTx
1/4 W
GND 7 8
7
6
25 5
4
3
RTS 4 2
1
CTS 5
15 Front
View
18
DANFOSS DRIVE

D-Sub Terminals
VLT2800/5000/6000
SHD
16 (RS485)
470
TxRx+ 22 68 TxRx+
220
1/4 W
TxRx- 10 69 TxRx-
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-13
ELAU DRIVE

D-Sub D-Sub
Max-4
VCC 16 (RS422)
470
1/4 W
See notes to follow.
Tx+ 23 4 RxD+
220
Tx- 12 5 RxD-
470
1/4 W
GND 7
25
Rx+ 13 3 TxD+
120
1/4 W
Rx- 24 2 TxD-
RTS 4
CTS 5
15
18
Max. 200 m.

D-Sub D-Sub
Max-4
Vcc 16 (RS485)
470 3 TxD+
1/4 W
See notes to follow.
TxRx+ 22 4 RxD+
220 120
TxRx- 10 5 RxD-
470
2 TxD-
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
Max. 200 m.
Communication between a VTxxxW device and ELAU Max-4 devices can

be established by using the ModBus Master Slow Peripherals protocol and
a communication speed between 9600 and 38400 baud.
You can use either a 4-wire RS422 or a 2-wire RS485 connection. In the
latter case it is essential to use the ELAU ModBus_v001001.lib library or a
later version. Using the RS485 connection allows you to connect more than
one ELAU device to the same VT port.
The Function-Block prepared by ELAU makes available 4 data arrays,

whose length can be defined by the user, for communication with the VT .
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
Characteristics of the arrays:
Name Type of data Notes

Bit
.B0000 The VT accesses this data area in both read and write
(read / write)
Bit
.B0001 The VT cannot access this data area
(read only)
The VT accesses this data area by selecting the option Input
Register as data area of the variabile in the VT .
Word Warning: The programmer must check that the change
.W3000
(read only) of the data field of the VT page does not get enabled. If
the change of the data field is enabled the equivalent
address in Array .W4000 will be overwritten.
Word The VT accesses this data area in both read and write by
.W4000
(read / write) selecting the option Word as data area.
N.B. :
Defining the length of the arrays in the programming SW, ELAU puts
the number 1 for the first element of the array; this implies the existence
of an offset of 1 between the address of the array element and the
address specified in the VT variable. E.g.: if, using the VT, you want to
read and edit the element at single word 20 of the array W4000, num-
ber 19 will have to be specified as the address of the VT variable.
To have retentive data in the ELAU device, the relevant array must be
declared as VAR_RETAIN.
Check that the ModBus address assigned in the configuration of the
device in VTWIN corresponds to the value assigned to the parameter
Modbus_SlaveNr of the ELAU Function Block.
EUROTHERM DRIVE
VT side Drive side. Order code:

D-Sub Phoenix
Series 605
4 SHD
16 (RS485)
470 1 TxB
1/4 W
TxRx+ 22 5 RxB Requires 584SV/605 communication card
220
1/4 W WARNING!!! For Hardware configuration refer to manual RS485 Communication
TxRx- 10 6 RxA Interface - HA463560 Issue 1 remembering that Dip-Switch SW1 DIP1 must be
470
2 TxA set at OFF and if it is the last in the chain DIP2 is set at ON (Terminated).
1/4 W
GND 7
For Software configuration refer to the same manual, remembering that the proto-
25
col DBUS RTU must be selected.
RTS 4
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-15
VT Side Drive side Order code:

Phoenix RJ45
5 Pin male 8 pin NOT CODED
631CAN - 635CAN - 637CAN
Shild 3 (CAN)
CAN+ 4 5 CAN_H
For the VT side cable termination see Chapter 34 -> CAN: Connection.
CAN- 2 4 CAN_L For the DRIVE side cable termination use the appropriate accessory BUS termi-
V- 1 6 CAN_GND nation plug (see Drive manual) in connector X20/21.
NOTE: The max. length of the cable depends on the transmission speed.
8 Trasmission speed (kbit/s) Length (m.)

7
6 20 800
5
4
3 50 600
2
1
125 500
Front
250 250
View
500 100
See note 1000 25
EVER DRIVE

D-Sub D-Sub
Ever MPP14-01
RxD 3 3 TxD (RS232)

TxD 2 2 RxD
GND 7 5 GND
25
RTS 4
CTS 5
15
18
FANUC ROBOTICS DRIVE

D-Sub D-Sub
R-J controllers
1 SHD (RS232)
RxD 3 2 TxD
TxD 2 3 RxD
GND 7 7 GND
25 4 RTS
RTS 4 5 CTS
CTS 5 6 DSR
15 8 CD
18 20 DTR
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
FAGOR DRIVE

D-Sub D-Sub
DNC PROTOCOL
RxD 3 3 TxD (RS232)

TxD 2 2 RxD
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub D-Sub
DNC PROTOCOL
VCC 16 (RS422)
470
1/4 W
Tx+ 23 9 #RxD422
330 330
1/4 W 1/4 W
Tx- 12 8 RxD422
470
1/4 W
GND 7
25
470
1/4 W
Rx+ 13 7 #TxD422
330 330
1/4 W 1/4 W
Rx- 24 6 TxD422
470
1/4 W
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-17
GALIL DRIVE

D-Sub D-Sub
Srie DMC 2x00
TxD 2 3 RxD (RS232)
RxD 3 2 TxD
GND 7 5 GND (See Chapter 40 -> Connecting the cable shield)
25 7 RTS
RTS 4 8 CTS
CTS 5
15
18
Max. 15 m.
GE DRIVE

D-Sub Terminals
VAT-23D
SHD
VCC 16 (RS485)
470
1/4 W
TxRx+ (See Chapter 40 -> Connecting the cable shield)
TxRx+ 22
P10
220
1/4 W
TxRx-
TxRx- 10
FSI
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
HITACHI DRIVE

D-Sub RJ45
25 pin male 8 pin NOT CODED
L-100
(RS422)
TX+ 23 2 RECEIVE
220 (SeeChapter 40 -> Connecting the cable shield)
1/4 W
TX- 12 3 RECEIVE
RX+ 13 5 SEND
220
1/4 W
RX- 24 6 SEND
25
GND 7 8
7
RTS 4 6
5
4
CTS 5 3
2
15 1
18 Front
View
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
KEB DRIVE

D-Sub D-Sub
Combivert F4C - F4S
RxD 3 2 TxD (RS232)

TxD 2 3 RxD
GND 7 7 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub D-Sub
Combivert F4C - F4S
TX+ 23 4 RX+ (RS422)

220
1/4 W
TX- 12 5 RX-
RX+ 13 8 TX+
220
1/4 W
RX- 24 9 TX-
25
GND 7
RTS 4
CTS 5
15
18

D-Sub D-Sub
Combivert F4C - F4S
16 (RS485)
470
8
TxRx+ 22 4
220
1/4 W
TxRx- 10 9
470
5
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-19
INDRAMAT DRIVE

D-Sub D-Sub
PCCR0-GP1
RxD 3 2 TD (RS232)
TxD 2 3 RD
SERIAL PORT 1 connection requires no parametrization, while the TYPE param-
GND 7 7 SG
eter like ASCII HOST needs to be set for SERIAL PORT 2. The MODE parameter
25 must be set as RS232.
RTS 4
CTS 5
15
18
Max. 12 m.

D-Sub D-Sub
PCCR0-GP1
VCC 16 (RS485)
470
1/4 W
SERIAL PORT 1 connection requires no parametrization, while the TYPE param-
TxRx+ 22 4 RS485+
220 eter like ASCII HOST needs to be set for SERIAL PORT 2. The MODE parameter
1/4 W must be set as RS485.
TxRx- 10 5 RS485-
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
LENZE DRIVE

D-Sub Terminals
SHD Series 82x

88
16 (RS485)
470
1/4 W
TxRx+ (See Chapter 40 -> Connecting the cable shield)
TxRx+ 22
(B) 71
220
1/4 W
TxRx-
TxRx- 10
(A) 72
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
Series 82x
RxD 3 2 TxD (RS232)

TxD 2 3 RxD
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.
VT Side Drive side Order code:

Phoenix Phoenix
5 Pin male 3 pin female NOT CODED
Series 93xx
Shild 3 PE (CAN)
CAN+ 4 HI
For the VT side cable termination see Chapter 34 -> CAN: Connection.
CAN- 2 LO For the DRIVE side cable termination use the related resistence (120Ohms, sup-
V- 1 GND plied with the device) between the HI and LO terminals in the X4 connector (see
also Drive manual).
NOTE: The length depends onthe type of cable.
See Note Length Resistence Capacity

Type of cable
(m) (Ohm/Km) (nF/Km)
=<300 LIYCY 2x2x0.5 mmq =<40 =<130
=<1000 CYPIMF 2x2x0.5 mmq =<40 =<60
LUST DRIVE

D-Sub D-Sub
C-Line Drive
RxD 3 2 TxD (RS232)

TxD 2 3 RxD
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-21
OMRON DRIVE

D-Sub Terminals
3G3EV
SHD
16 Card PJVOP485 required
470
1/4 W (RS485)
TxRx+ 22 2 (S/R+)
220
1/4 W MODBUS RTU STANDARD PROTOCOL
TxRx- 10 1 (S/R-)
1/4 W
GND 7 3 (SG)
25
RTS 4
CTS 5
15
18
OSAI DRIVE

D-Sub D-Sub
10 Series GP
TxD 2 2 Rx (RS232)
RxD 3 3 Tx
See Chapter 40 -> Connecting the cable shield)
GND 7 5 GND
25 7 RTS
RTS 4 8 CTS
CTS 5 6 DSR
15 4 DTR
18
Max. 15 m.
PANASONIC DRIVE

D-Sub Minidin
MSS*XP Series
RxD 3 3 Tx (RS232)
TxD 2 5 Rx
GND 7 4 GND
25
RTS 4
CTS 5
15 5
8
Front 2
18 7 4
View 6
1
3
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
PARKER AUTOMATION DRIVE

D-Sub terminals
6000/ZETA Controller
SHD
COM1 serial port
RxD 3 Tx
TxD 2 Rx (RS232)
GND 7 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub D-Sub
COMPUMOTOR 6K
RxD 3 3 Tx (RS232)
TxD 2 2 Rx
Dip-Switch SW1:
GND 7 5 GND
1 -> OFF
25 2 -> OFF
RTS 4 3 -> OFF
4 -> OFF
CTS 5
5 -> OFF
15 6 -> OFF
18 7 -> OFF
8 -> OFF
WARNING!!! For Hardware configuration refer to manual 6K Series Hardware

Installation Guide.
Max. 15 m. (See Chapter 40 -> Connecting the cable shield)

D-Sub D-Sub
COMPUMOTOR 6K
(RS485)
4 TDB
Dip-Switch SW1:
TxRx+ 22 1 RDB
120
1 -> OFF (ON - Only if the last node)
1/4 W 2 -> OFF (ON - Only if the last node)
TxRx- 10 7 RDA 3 -> OFF
4 -> OFF
8 TDA
5 -> OFF
GND 7 6 GND 6 -> OFF
25 7 -> OFF
8 -> OFF
RTS 4
CTS 5 WARNING!!! For Hardware configuration refer to manual 6K Series Hardware
15 Installation Guide.
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-23

D-Sub D-Sub
COMPUMOTOR 6K
TX+ 23 1 RDB (RS422)

120
1/4 W
Dip-Switch SW1:
TX- 12 7 RDA
11 -> OFF (ON - Only if the last node)
RX+ 13 4 TDB 2 -> OFF (ON - Only if the last node)
120 3 -> OFF
1/4 W
RX- 24 8 TDA
4 -> OFF
5 -> OFF
25 6 GND 6 -> OFF
GND 7 7 -> OFF
RTS 4 8 -> OFF
CTS 5 WARNING!!! For Hardware configuration refer to manual 6K Series Hardware
15 Installation Guide.
18

D-Sub D-Sub
GT6/GV6 Controller
RxD 3 3 Tx (RS232)
TxD 2 2 Rx
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.
ROBOX DRIVE

D-Sub D-Sub
RBXE/RBXM
Serial ports: P.SER1 - P.SER2
RxD 3 2 Rx
TxD 2 3 Tx (RS232)
GND 7 5 GND
25 6 DSR
RTS 4 4 DTR
CTS 5 7 RTS
15 8 CTS
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
RBXE/RBXM
Serial ports: P.SER3 - P.SER4
Tx+ 23 10 RxD+
Tx- 12 2 RxD- (RS422)
Rx+ 13 9 TxD+
Rx- 24 1 TxD-
GND 7 8 GND
25 6 DTR-
RTS 4 7 DSR-
CTS 5 14 DTR+
15 15 DSR+
18
S.B.C. DRIVE

D-Sub D-Sub
HPD 2 - 5 - 8 - 16
15 8 SHD (RS422)
18 6 BR+
Device address: 0...31
TX+ 23 2 RX+
220
TX- 12 4 RX-
7 BR-
RX+ 13 1 TX+
220
1/4 W
RX- 24 3 TX-
RTS 4
CTS 5
GND 7
25

D-Sub D-Sub
HPD 2 - 5 - 8 - 16
8 SHD (RS485)
16 6 BR+
470 Device address: 0...31
1 TX+
1/4 W
TxRx+ 22 2 RX+ (See Chapter 40 -> Connecting the cable shield)
220
1/4 W
TxRx- 10 4 RX-
470
3 TX-
1/4 W
GND 7 7 BR-
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-25
SEW-EURODRIVE DRIVE

D-Sub D-Sub
MOVIDYN
(RS232)
RxD 3 2 TxD
TxD 2 3 RxD Communication card SEW-EURODRIVE USS21A required
GND 7 5 GND
25 N.B: Not valid for terminals VT50 and VT60.
RTS 4 4 DTR
CTS 5
15
18
Max. 15 m.

D-Sub Terminals
MOVIDYN
SHD
16 (RS485)
470
1/4 W
Communication card SEW-EURODRIVE USS21A required
TxRx+ 22 TxRx+
220
TxRx- 10 TxRx-
470
1/4 W
GND 7 GND
25
RTS 4
CTS 5
15
18

D-Sub D-Sub
MOVITRAC - MOVIDRIVE
(RS232)
RxD 3 2 TxD
TxD 2 3 RxD Communication card SEW-EURODRIVE USS21A required
GND 7 5 GND
RTS 4
CTS 5
15
18
Max. 5 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub Terminals
MOVITRAC - MOVIDRIVE
SHD
16 (RS485)
470
1/4 W Communication card SEW-EURODRIVE USS21A required
TxRx+ 22 +
220
TxRx- 10 -
470
1/4 W
GND 7 0V5
25
RTS 4
CTS 5
15
18
SIEI DRIVE

D-Sub D-Sub
SLINK 3
16 (RS485)
470
1/4 W WARNING!!!
TxRx+ 22 3 TxRx+
220 If the jumpers S18 and S19 on the regulator card are in position A (serial line gal-
1/4 W vanically isolated from the regulator section), pin 5 and 9 must be connected to
TxRx- 10 7 TxRx- the power unit.
470
GND 7 5 0V
25 9 +5V
RTS 4
CTS 5
15
18
SIEMENS DRIVE

D-Sub D-Sub
SIMOVERT
RxD 3 7 TxD (RS232)

TxD 2 2 RxD
GND 7 5 G ND
25
RTS 4
CTS 5
15
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-27

D-Sub D-Sub
SIMOVERT
16 (RS485)
470
1/4 W
TxRx+ 22 3 RS485P
220
1/4 W
TxRx- 10 8 RS485N
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
STBER DRIVE

D-Sub D-Sub
FAS / FDS / SDS 4000
RxD 3 4 Tx (RS232)
TxD 2 2 Rx
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.
TDE MACNO DRIVE

D-Sub D-Sub
DMBL Series
16 (RS485)
470
3
TxRx+ 22 2 TxRx+
220
1/4 W
TxRx- 10 6 TxRx-
470
7
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
TELEMECANIQUE DRIVE

D-Sub D-Sub
ALTIVAR 58
TxRx+ 22 7 D (B) (RS485)

220 120
TxRx- 10 3 D (A)
GND 7 4 GND
25
RTS 4
CTS 5
15
18
TRIO MOTION DRIVE

D-Sub Minidin
TRIO MOTION Modbus
RxD 3 3 Tx (RS232)
TxD 2 5 Rx
25
RTS 4
CTS 5
15 5
8
Front 2
18 7 4
View 6
1
3
Max. 15 m.

D-Sub Minidin
TRIO MOTION Modbus
Tx+ 23 1 Rx+ (RS422)

Tx- 12 2 Rx-
Rx+ 13 8 Tx+
Rx- 24 7 Tx-
GND 7
25
15 5
8
2
18 7 4
1
6
3
Front
View
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-29
DATALOGIC BARCODE READER
VT side Barcode side Order code:

D-Sub D-Sub
DL-910
RxD 3 2 Tx (RS232)
TxD 2 3 Rx
CTS 5 4 RTS (See Chapter 40 -> Connecting the cable shield)
RTS 4 5 CTS
GND 7 7 GND
25
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
ABB PLC
VT side PLC side Order code:

D-Sub D-Sub
25 pin male 15 pin male CVPLC03102
T200 (KP60)
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
RTS 4 5 CTS
GND 7 9 GND
25 10
15 7 DSR
18 8
14 +12V
Max. 15 m.

D-Sub D-Sub
CS31 (KR31 / KT31 / KR91 / KT92 / KT93 / KT94 / KT95)
T200 (KP62)
1 SHD
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
This note only applies to protocol of CS31 series 90 (non direct).
GND 7 7 G ND
Once the VT has been connected to and disconnected from the CS31, the PLC
25 8 0V remains in MONITOR mode and the programming software no longer functions
15 6 PRG properly. To get the PLC back to normal functioning, use the programming S/W to
access the PLC commun.2" menu and select the "3 terminal emulation" option
18
and press the "CTRL" and "W" keys together. At the end the PLC responds by
CTS 5 4 RTS offering the prompt sign ">".
RTS 4 5 CTS
NOTE ON DIRECT PROTOCOL: You can select the communication speed of
19200 Baud in the PLC by connecting pins #6, #7 and #8 (see fig.). This speed is
handled by CS31 only if the library module CE 19_2COM1is loaded.
Max. 15 m. NOTE: the cable supplied by ESA does not have the connection represented by
the dotted line.

D-Sub D-Sub
CS31 (KR31 / KT31)
1 SHD (RS232)
RxD 3 2 TxD
TxD 2 3 RxD MODBUS RTU STANDARD PROTOCOL
RTS 4 5 CTS
GND 7 7 GND
25 8 0V
15 6 PRG
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-31

D-Sub D-Sub
CS31 (07KP92 R101)
MODBUS RTU Communication module, COM3 and COM4 ports
1 SHD
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
STANDARD MODBUS RTU PROTOCOL
GND 7 7 GND
25 6 PRG (See Chapter 40 -> Connecting the cable shield)
RTS 4 4 RTS
CTS 5 5 CTS
15
18
Max. 15 m.

D-Sub D-Sub
CS31 (07KP92 R101)
1 SHD
TX+ 23 10 RxD-P (RS422)
220
1/4 W STANDARD MODBUS RTU PROTOCOL
TX- 12 11 RxD-N
RX+ 13 8 TxD-P (See Chapter 40 -> Connecting the cable shield)
220
1/4 W
RX- 24 9 TxD-N
RTS 4 12 RTS-P
CTS 5 14 CTS-P
GND 7 13 RTS-N
25 15 CTS-N
15
18

D-Sub D-Sub
CS31 (07KP92 R101)
16 1 SHD
470
(RS485)
1/4 W
RxD-P
TxRx+ 22 10
TxD-P STANDARD MODBUS RTU PROTOCOL
220
1/4 W
RxD-N
TxRx- 10 11 (See Chapter 40 -> Connecting the cable shield)
TxD-N
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub Minidin
CS31 Series 40&50

RxD 3 2 Tx
TxD 2 1 Rx
GND 7 7
25 6
RTS 4 3
CTS 5
15 5
8
2
18 7 4
1
6
3
Front
View
Max. 15 m.

D-Sub D-Sub
AC70
RxD 3 2 TxD (RS232)

TxD 2 3 RxD
25
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub RJ45
ACS210
Tx+ 2 6 RD (RS232)

5 0V
Rx+ 3 3 TD
GND 7 4 0V
25
15
8
7
18 6
5
4
3
2
1
Front
View
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-33

D-Sub D-Sub
25 pin male 9 pin female CVPLC06402
AC450
RxD 3 3 Xmt (RS232)

TxD 2 2 Rcv
25 7 RTS
RTS 4 8 CTS
CTS 5 6 DSR
15 4 DTR
18 1 DCD
Max. 15 m.
AEG MODICON PLC

D-Sub D-Sub
COMPACT, A120, A250
Port 1 - Port 2
RxD 3 3 TxD
TxD 2 2 RxD (RS232)
GND 7 5 GND
25 6
RTS 4 4
CTS 5 7
15 8
18
Max. 15 m.

D-Sub RJ45
25 pin male 8 pins CVPLC17202
MICRO
RxD 3 3 TxD (RS232)

TxD 2 4 RxD
25 6 RTS
RTS 4 7 CTS
CTS 5
15 8
7
6
18 5
4
3
2
1
Front
View
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
ALLEN-BRADLEY PLC

D-Sub RJ45
SLC 500 CPU 5/02 5/03
SHD
VCC 16 (RS485)
470
1/4 W
TxRx+ 22 1 Address of VT : 1...31
220 Address of PLC : 1...31
1/4 W
TxRx- 10 2 Screen side SLC500 connected to earth terminal of PLC power unit
470
1/4 W WARNING !!!
GND 7 8
7 See warnings regarding VT <-> SLC500 connection.
6
25 5
4
RTS 4 3 N.B: Open Integer file for at least two elements
2
1
CTS 5
Front Example:
15 View N7:0
18 N7:1
CONNECTION TO BE AVOIDED!!! Avoid connections like that

shown in the figure below. The DH485 (data highway) port of
CPUs 5/02 - 5/03 is not protected against peaks caused by outside dis-
turbances; these could lead to serial port DH485 of SLC500 being dam-
aged.
CVPLC07112
VT SLC500
terminal (DH485)
Below are listed those types of connection that are recommended.
CVPLC07112 ESA
VT protective SLC500
terminal device (DH485)
6 cm
3x3 cm 19 cm
Order code for device: CVPLC07502
Allen-Bradley Allen-Bradley
CVPLC07112 Isolated Link cable
VT SLC500
terminal Coupler type: (DH485)
1747-C11
1747-AIC
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-35

D-Sub D-Sub
PLC 5 /11/20/30/40/40L/60/60L
RxD 3 2 TxD (RS232)

TxD 2 3 RxD
GND 7 7 GND "CH0" SERIAL PORT SET
Channel 0 : SYSTEM (Point-to-point)
25 4 RTS Diag. File :0
RTS 4 5 CTS Remote Mode Change : DISABLED
CTS 5 6 DSR Baud Rate : 19.2K
Stop Bits :1
15 20 DTR
Parity : NONE
18 8 DCD Control Line : NO HANDSHAKING
Duplicate Detect : OFF
ACK Timeout (20 ms.) : 50
Error Detect : BCC
NAK Receive :3
DF1 ENQS :3
Max. 15 m.
N.B: Open Integer file for at least two elements
Example:
N7:0
N7:1

D-Sub D-Sub
PLC 5 /11/20/30/40/40L/60/60L
VCC 16 4 RTS- (RS422)

470
5 CTS-
1/4 W
"CH0" SERIAL PORT SET
Tx+ 23 16 Rx+
220 220 Channel 0 : SYSTEM (Point-to-point)
1/4 W 1/4 W Diag. File :0
Tx- 12 3 Rx- Remote Mode Change : DISABLED
470 Baud Rate : 19.2K
6 DSR-
1/4 W Stop Bits :1
GND 7 20 DTR- Parity : NONE
25 8 DCD- Control Line : NO HANDSHAKING
Rx+ 13 14 Tx+ Duplicate Detect : OFF
220 220 ACK Timeout (20 ms.) : 50
1/4 W 1/4 W Error Detect : BCC
Rx- 24 2 Tx- NAK Receive :3
RTS 4 22 DSR+ DF1 ENQS :3
CTS 5 23 DTR+ N.B: Open Integer file for at least two elements
15 10 DCD+
18 19 RTS+ Example:
N7:0
13 CTS+
N7:1
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
SLC 500 CPU 5/03 5/04 5/05
MICROLOGIX CPU5550
RxD 3 3 TxD ControlLogix
TxD 2 2 RxD
GND 7 5 GND (RS232)
25 7 RTS "CH0" SERIAL PORT SET
RTS 4 8 CTS DF1 full duplex mode
CTS 5 1 DSR Baud rate : 19200
Duplicate Detect : DISABLED
15 4 DTR
ACK timeout : 50
18 6 DCD Parity : NONE
Control Line : NO HANDSHAKING
Error detect : BCC
NAK retries :3
ENQ retries :3
Embedded responses : ENABLED
Max. 15 m.
Example:
N7:0
N7:1
N.B. Programming SW necessary for Allen-Bradley V4.00 and all after
VT side (Active) PLC side Order code:

D-Sub D-Sub
MICROLOGIX CPU1000, 1200 and 1500
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
GND 7 5 GND MICROLOGIX SERIAL PORT SET
DF1 full duplex mode (MICRO)
25
Baud rate : 9600
RTS 4 ACK timeout : 50
CTS 5 Parity : NONE
Error detect : CRC
15
NAK retries :3
18 ENQ retries :3
Embedded responses : ENABLED
Duplicate packed detect : NO
Max. 15 m. Example:
N7:0
N7:1
The Db 9 pin male connector must be connected to the A-B 1761-CBL-PM02,

SER, A cable of the MICROLOGIX PLC.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-37

D-Sub RJ45
25 pin male 8 pins NOT CODED
#1 SLC 500 CPU 5/02 5/03
SHD
(RS485)
TxRx+ 22 1 TxRx+ Cable valid for several VTs connected to a single PLC.
TxRx- 10 2 TxRx- Address of VT : 1...31

Address of PLC : 1...31
GND 7
25 N.B: Open Integer file for at least two elements
RTS 4
8 Example:
CTS 5 7
6 N7:0
15 5 N7:1
4
3
18 2
1 NOTE:
If using the 1747 AIC module, use the cable without the RJ45 connector employ-
Front ing the terminals.
#n View
1 -> 5 (A)
2 -> 4 (B)
TxRx+ 22
GND -> 2 (SHLD)
TxRx- 10 (See Chapter 40 -> Connecting the cable shield)

GND 7
25
RTS 4
CTS 5
15
18
#Last
TxRx+ 22
220
1/4 W
TxRx- 10
GND 7
25
RTS 4
CTS 5
15
18
Example of the construction of a cable for connecting several VTs

to a single PLC.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
ALTUS PLC

D-Sub D-Sub
ALNET-1
RxD 3 7 TxD (RS232)

TxD 2 1 RxD
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 3 m.

D-Sub RJ45
ALNET-1
SHD
RxD 3 2 Tx (RS232)
TxD 2 3 Rx
GND 7 5 GND
25
RTS 4
CTS 5
15 8
7
6
18 5
4
3
2
1
Front
View
Max. 3 m.

D-Sub D-Sub
ALNET-1
VCC 16 (RS485)
470
4 RxD+
TxRx+ 22 3 TxD+
220
1/4 W
TxRx- 10 8 TxD-
470
9 RxD-
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-39

D-Sub RJ45
ALNET-1
SHD
VCC 16 (RS485)
470
TxRx+ 22 5 TxRx+
220
1/4 W
TxRx- 10 8 TxRx-
470
1/4 W
GND 7 8
7
6
25 5
4
3
RTS 4 2
1
CTS 5
Front
15 View
18
ATOS PLC

D-Sub RJ11
MPC1600, MPC2002, MPC4004
RxD 3 3 Tx (RS232)
TxD 2 2 Rx
GND 7 5 GND
25
RTS 4
1
CTS 5 2
3
4
15 5
6
18
Front
View
Max. 15 m.

D-Sub Terminals
25 pin male CVPLC29202
MPC1600, MPC2002, MPC4004
SHD
VCC 16 (RS485)
470
TxRx+ 22 2 DO/RI
220
1/4 W
TxRx- 10 1 DO/RI
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
BECKHOFF PLC

D-Sub D-Sub
BX3100
RxD 3 2 TxD (RS232)

TxD 2 3 RxD
COM1 Port
GND 7 5 GND
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub D-Sub
BX3100
RxD 3 8 TxD (RS232)
TxD 2 7 RxD
GND 7 9 GND COM2 Port
25
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub D-Sub
BX3100
16 (RS485)
470
1/4 W
TxRx+ 22 6 TxRxD+ COM2 Port
220
1/4 W Terminations are not needed on cables of less than 5 meters and a transmission
TxRx- 10 1 TxRxD- speed of less than 19200 Baud.
470
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-41

D-Sub terminals
KL6001
4 Shild
RxD 3 1 TxD (RS232)
TxD 2 5 RxD
GND 7 7 GND
25 2 RTS
RTS 4 6 CTS
CTS 5
15
18
Max. 15 m.

D-Sub terminals
KL6021
4 Shild
VCC 16 (RS485)
470
2 RxD+
TxRx+ 22 1 TxD+ speed of less than 19200 Baud.
220
1/4 W
TxRx- 10 5 TxD- (See Chapter 40 -> Connecting the cable shield)
470
6 RxD-
1/4 W
GND 7
25
RTS 4
CTS 5
15
18

D-Sub D-Sub
BC7300/BK7300
VCC 16 (RS485)
470
TxRx+ 22 3 TxRxD+
speed of less than 19200 Baud.
220
1/4 W
TxRx- 10 8 TxRxD- (See Chapter 40 -> Connecting the cable shield)
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
BOSCH PLC

D-Sub D-Sub
CL150
RxD 3 3 TxD (RS232)

TxD 2 2 RxD
GND 7 7 G ND
25
RTS 4
CTS 5
15
18
Max. 15 m.
B&R AUTOMATION PLC

D-Sub D-Sub
NET2000
RxD 3 3 TxD (RS232)

TxD 2 2 RxD
GND 7 5 G ND
25
RTS 4
CTS 5
15
18
Max. 15 m.
CROUZET RPX PLC
VT side Traslator side Order code:

D-Sub D-Sub
RPX 10 - 20 - 30
Using CROUZET 88 750 309 translator
RxD 3 3 TxD
TxD 2 2 RxD (RS232)
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-43
FOXBORO PLC

D-Sub RJ45
RTU20
RxD 3 4 Tx (RS232)
TxD 2 5 Rx
GND 7 6 GND
25
RTS 4
CTS 5
15 8
7
6
18 5
4
3
2
1
Front
View
Max. 15 m.
FUJI PLC

D-Sub
Frame Micrex-F F705

FG
GND
VCC 16 Needs RS4 communication card.
470
1/4 W
Recive NOTE:
Tx+ 23 RA
220 A To insert the termination resistances move the relevant switch to the ON position.
1/4 W
Recive (RS422)
Tx- 12 RB
470 B
GND 7
25
Send
Rx+ 13 SA
220 A
1/4 W Send
Rx- 24 SB
B
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
GE FANUC PLC

D-Sub D-Sub
Series 90 and 90 MICRO
directly in the CPU programming connector
VCC 16 1 SHD
470 Versamax
1/4 W
using port 2
Tx+ 23 11 Rx+
(RS422)
Tx- 12 10 Rx-
1/4 W
GND 7 7 GND
25
Rx+ 13 13 Tx+
Rx- 24 12 Tx-
RTS 4 6 RTS-
CTS 5 15 CTS-
15 14 RTS+
18 8 CTS+

D-Sub D-Sub
Series 90
Using GE FANUC CMM311 interface port 1 - port 2
1 SHD
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
CONFIGURATION OF CMM311:
GND 7 7 GND
SNP only
25 4 RTS SNP Enable : Yes
RTS 4 5 CTS SNP Mode : Slave
Interface : RS232 (port1 / port2)
CTS 5
Data Rate : 19200
15 Timeout : Long
18 Parity : Odd
Stop bits :1
Flow control : None
TurnA delay : None
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-45

D-Sub D-Sub
Series 90
Using GE FANUC CMM311 interface
VCC 16 1 SHD
470 (RS422)
24 TERM
1/4 W
Tx+ 23 25 Rx+ CONFIGURATION OF CMM311:
SNP only
SNP Enable : Yes
Tx- 12 13 Rx- SNP Mode : Slave
470 Interface : RS422 (solo port2)
1/4 W Data Rate : 19200
GND 7 7 GND Timeout : Long
25 Parity : Odd
Stop bits :1
Rx+ 13 21 Tx+ Flow control : None
TurnA delay : None
Rx- 24 9 Tx-
RTS 4 10 RTS-
CTS 5 11 CTS-
15 22 RTS+
18 23 CTS+

D-Sub RJ45
Versamax
SHD using port 1
RxD 3 4 TxD
TxD 2 3 RxD (RS232)
GND 7 8 G ND
25 1 RTS
RTS 4 2 CTS
CTS 5
15 8
7
6
18 5
4
3
2
1
Front
View
Max. 15 m.
GEFRAN PLC

D-Sub D-Sub
Series MPS-NS
RxD 3 15 Tx (RS232)
TxD 2 14 Rx
25 12
RTS 4 11
CTS 5 4
15 5
18
Max. 10 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
HITACHI PLC

D-Sub D-Sub
Series H, 02H
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
RTS 4 5 CTS
GND 7 9 GND
25 10
15 7 DSR
18 8
14 +12V
Max. 15 m.

D-Sub D-Sub
Series EM CPU CPM - E3
RxD 3 3 SD (RS232)
TxD 2 2 RD
CTS 5 7 RS WARNING!!
Switch ext. to COM2
RTS 4 8 CS Switch n2 int. to ON
GND 7 5 SG
15
18
Max. 15 m.

D-Sub Minidin
Series EC
RxD 3 4 SD (RS232)
TxD 2 8 RD
CTS 5 2 RS WARNING!!
Switch ext. to COM2
RTS 4 3 CS Areas T, C (time, counters) read only
GND 7 6 SG
15 4
1
7
18 2 5
8
3
6
Soldered
end
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-47
VT side PLC Side Order code:

D-Sub Minidin
Series H CPU22-02 HC
RxD 3 4 TxD (RS232)

TxD 2 8 RxD
COM2
CTS 5 2 RTS
RTS 4 3 CTS (See Chapter 40 -> Connecting the cable shield)
GND 7 6 GND
25 7
15 5
18 1
1 4
Soldered 7
2 5
End 3
8
6
Max. 15 m.

D-Sub RJ45
SHD
Series EH150
(RS232)
RxD 3 5 TxD
TxD 2 6 RxD NOTE:
RTS 4 7 CTS 127 PLCs connectable in Hitachi network with 2 Links (0-63 stations per Link).
CTS 5 8 RTS
LUMP:
GND 7 1 GND
25 Parameter Default Values Notes
15 8 01,02 or
7 L FF Address of Link number.
6 FF
18 5
4
3 00-63 or Address of network node (as indicated by
2 U FF
1 FF the network card rotary switches).
Front Address of network node with connection
View M 00 00-63
using COMM-H additional serial cards.
Address of network node with connection
Max. 15 m. P 00 00-63
using COMM-H additional serial cards.
TM:
Parameter Default Values Notes

TM 4 4-F Timeout for the reply to an enquiry.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub Terminals
SHD COMM H
(RS422)
TX+ 23 RxDP
1/4 W
TX- 12 RxDN
RX+ 13 TxDP
220
1/4 W
RX- 24 TxDN
25 RxDG
GND 7 TxDG
RTS 4
CTS 5
15
18
IDEC IZUMI PLC

D-Sub FUJITSU
CPU FA2 - FA2J
In the CPU programming connector (Programmer's Port).
4 SHD
GND 7 8 SHD (Current loop).
Rx- 25 6 0V (See Chapter 40 -> Connecting the cable shield)
Rx+ 18 2 Rx
IKT 14
RTS 4 7 0V
560
CTS 5
1/4 W
Tx- 11 3 Tx
TX+ 9 1 12Vdc
Soldered 4 3 2 1
End 8 7 6 5
Max. 200 m.

D-Sub Minidin
IZUMI Micro3

470
1/4 W
TxRx+ 22 7 TxRx+
220
1/4 W
TxRx- 10 8 TxRx-
470
1/4 W
GND 7
25
1 4
RTS 4 7
2 5
CTS 5 8
3
6
15
Soldered
18
end
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-49
KLCKNER MOELLER PLC

D-Sub DIN
PS306
SHD
(RS485)
TxRx+ 22 4 A
220 N.B. Make sure that the two insertion jumpers of the interface termination resis-
1/4 W tances located in the RS485 hatch (visible on the front part of the PLC) are
TxRx- 10 1 B hooked up (see PLC manual).
GND 7
25
RTS 4
1
4
CTS 5
2
15 5
3
18
Soldered
end

D-Sub D-Sub
PS316/PS416-CPU400
TxRx+ 22 3 A (RS485)
220
1/4 W N.B. Make sure that the two insertion jumpers of the interface termination resis-
TxRx- 10 7 B tances located in the RS485 hatch (visible on the front part of the PLC) are
GND 7 hooked up (see PLC manual).
25
RTS 4
CTS 5
15
18

D-Sub DIN/B
PS4-141-MM1
SHD PS4-201-MM1
PS4-341-MM1
Rx 3 5 Tx
(RS232)
Tx 2 2 Rx
25
RTS 4
CTS 5
1
6 4
15
8 2
18 7 5
3
Soldered
end
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
PS416-CPU400
Rx 3 3 Tx (RS232)
Tx 2 2 Rx
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.
KEYENCE PLC

D-Sub RJ11
Series KV10-16-24-40
RxD 3 5 SD (RS232)
TxD 2 3 RD
GND 7 4 SG
25
RTS 4
1
CTS 5 2
3
4
15 5
6
18
Front
View
Max. 15 m.
KOYO PLC

D-Sub RJ11
DL 240 CPU Port
RxD 3 4 Tx (RS232)
TxD 2 3 Rx
25
RTS 4
6
CTS 5 5
4
15 3
2
1
18
Front
View
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-51

D-Sub RJ11
DL 340 CPU Port
RxD 3 2 Tx (RS232)
TxD 2 1 Rx
25
RTS 4
CTS 5
4
3
15 2
1
18
Front
View
Max. 15 m.

D-Sub D-Sub
DL 405 DCM, DL 405 CPU Port, DL 305 DCU
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
25 4
RTS 4 5
CTS 5
15
18
Max. 15 m.

D-Sub D-Sub
DL 405 DCM, DL 305 DCU
VCC 16 (RS422)
470
1/4 W
Tx+ 23 17 +IN (See Chapter 40 -> Connecting the cable shield)
220
1/4 W
Tx- 12 16 -IN
470
1/4 W
GND 7 7 GND
25
Rx+ 13 14 +OUT
220
1/4 W
Rx- 24 15 -OUT
RTS 4 10 +RTS
CTS 5 12 +CTS
15 11 -RTS
18 13 -CTS
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
DL 305 DCU
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
25 20 DTR
RTS 4 25 +5V
CTS 5
15
18
Max. 15 m.
KUHNKE PLC

D-Sub D-Sub
KUBES
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
25
RTS 4
CTS 5
15
18
Max. 15 m.
LG PLC

D-Sub D-Sub
K30 / K500 /K1000
RxD 3 3 TxD (RS232)

TxD 2 2 RxD
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-53

D-Sub D-Sub
K10
RxD 3 2 TxD (RS232)

TxD 2 3 RxD
GND 7 5 GND The 9 pin male Db must be connected to the GOLDSTAR cable of the K10 PLC.
25
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub terminals
Series MK
SHD
16 (RS485)
470
1/4 W
TxRx+ 22 TxRx+ (See Chapter 40 -> Connecting the cable shield)
220
1/4 W
TxRx- 10 TxRx-
470
1/4 W
GND 7 GND
25
RTS 4
CTS 5
15
18

D-Sub D-Sub
Master K1205
RxD 3 7 TxD2 (RS232)

TxD 2 4 RxD2
Dip-Switch:
GND 7 5 SG
1 -> OFF (ROM MODE)
25 2 -> ON (BUILT-IN CNET)
RTS 4
CTS 5
15
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub terminals
Master K1205
SHD
VCC 16 (RS485)
470
1/4 W
TxRx+ 22 + RS485+
220
1/4 W
TxRx- 10 - RS485-
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
MATSUSHITA-NAIS PLC

D-Sub Microdin
Series FP-1
Directly in the CPU programming connector
VCC 16
470 (RS422)
1/4 W
Tx+ 23 6 Rx+
150 NOTA:
1/4 W If you wish to use the AFP1523 cable it will be necessary to create an adaptor
Tx- 12 3 Rx- cable that on the VT side uses a 25 pin male D-Sub with the pins arranged as in
470 the figure, on the PLC side a 15 pin male D-Sub connector that must be wired as
1/4 W follows:
GND 7
25 Microdin -> D-Sub
Rx+ 13 5 Tx+
6 Rx+ -> 15
150 3 Rx- -> 7
1/4 W 5 Tx+ -> 14
Rx- 24 2 Tx- 2 Tx - -> 12
RTS 4
CTS 5 5
7 2
15 8 4
18 Front 6 1
3
View
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-55

D-Sub D-Sub
Series FP-1 / FP-M
Using the optional serial interface of the PLC
1 SHD
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
RS232C: RS232C SERIAL PORT SET
GND 7 7 GND
Port Selection : COMPTR LNK
25 4 RTS RS232C Send Form
CTS 4 5 CTS Data Length : 8 BIT
Parity CHK : WITH, ODD
RTS 5
Stop Bit : 1 BIT
15 Terminator : CR
18 Header : NO STX
RS232C Baudrate : 1(9600 bps )
RS232C Modem
Connection : DISABLED
Computer Link Station
Max. 15 m. number (1-32) :1

D-Sub Minidin
Series FP-M/FP-0/FP-2
In the programming connector of the CPU (Programmer's Port).
RxD 3 2 Tx
TxD 2 3 Rx (RS-232)
GND 7 1 GND
25
RTS 4
CTS 5 4 2
1
15
5
3
18
Soldered
end
Max. 15 m.

D-Sub D-Sub
Series FP-3
Direct in the programming connector of the CPU
VCC 16
470 (RS422)
1/4 W
Tx+ 23 10 Rx+
1/4 W
Tx- 12 3 Rx-
470
1/4 W
GND 7
25
Rx+ 13 9 Tx+
150
1/4 W
Rx- 24 2 Tx-
RTS 4 4 RTS
CTS 5 5 CTS
15 11
18 12
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
MICROLINK PLC

D-Sub Minidin
ML-14
RxD 3 5 TxD (RS232)
TxD 2 1 RxD
25
RTS 4
CTS 5
15 5
8
2
18 7 4
1
6
3
Front
View
Max. 15 m.

D-Sub terminals
ML-14
SHD
VCC 16 (RS485)
470
1/4 W
TxRx+ 22 + TxRx+ (See Chapter 40 -> Connecting the cable shield)
220
1/4 W
TxRx- 10 - TxRx-
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
MITSUBISHI PLC

D-Sub D-Sub
Series Fx
Using Computer-Link
1 SHD
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
Jump-connect the LG and GF terminals on the PLC terminal block
GND 7 7 GND
25 4 RTS (See Chapter 40 -> Connecting the cable shield)
RTS 4 5 CTS
CTS 5 6 DSR
15 20 DTR
18 8 DCD
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-57

D-Sub D-Sub
Series Fx
Rx+ 13 3 Tx+ (See Chapter 40 -> Connecting the cable shield)

220
1/4 W
Rx- 24 16 Tx-
Tx232 2 15 Rx-
GND 7 2K2
1/4 W
25 2 Rx+
RTS 4 4 DSR+
CTS 5 7 GND
15 8 GND
18 20 GND
21 /PWE

D-Sub D-Sub
Series A
( CPU port)
Using the MITSUBISHI SC-05 converter for long distances
RxD 3 3 TxD
TxD 2 2 RxD Jump-connect the LG and GF terminals on the PLC terminal block
RTS 4 4 CTS
GND 7 7 GND
25
+5V 16
CTS 5
15
18
Max. 15 m.

D-Sub D-Sub
Series A
Rx+ 13 3 Tx+ (RS232)

220 Directly in the CPU programming connector
1/4 W
Rx- 24 16 Tx- Jump-connect the LG and GF terminals on the PLC terminal block
Tx232 2 15 Rx-
2K2 (See Chapter 40 -> Connecting the cable shield)
1/4 W
RTS 4 17 DSR-
25 2 Rx+
GND 7 4 DSR+
+5V 16 7 GND
CTS 5 8 GND
15 20 GND
18 21 /PWE
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub Minidin
Series Fx0 - Fx0 N - Fx2 N
Directly in the CPU programming connector
Rx+ 13 2 Tx+
220 (RS-232/422 Hybrid)
1/4 W
Rx- 24 5 Tx- (See Chapter 40 -> Connecting the cable shield)
Tx232 2 7 Rx-
GND 7 2K2
1/4 W
25 8
RTS 4 4 GND
CTS 5
15 4
1
18
Soldered 7
2 5
end 3
8
6
OMRON PLC

D-Sub D-Sub
Using interface 3G2A6-LK201-EV1 and OMRON series H C200H-LK201
1 SHD (RS232)
RxD 3 2 TxD
Jump-connect the GR and LG terminals on the PLC terminal block
TxD 2 3 RxD
25 4 RTS
RTS 4 5 CTS
JUMPER SETTINGS C200H-LK201
CTS 5
15
Rear-fend jumpers Front-end switches
18
Off SW3 5 SW4 2

On
1 2 3 4 Cts 0V
Max. 15 m.

D-Sub D-Sub
Series H
Compact family C20H / C28H C40H / C60H
1 SHD
RxD 3 2 TxD (RS232)
TxD 2 3 RxD
GND 7 7 GND
25 4 RTS (See Chapter 40 -> Connecting the cable shield)
RTS 4 5 CTS
CTS 5
15
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-59

D-Sub D-Sub
Series H C200H using interface LK202
7 SHD
(RS422)
TX+ 23 1 RX+
2 20
1/4 W Jump-connect the GR and LG terminals on the PLC terminal block
TX- 12 6 RX-
VCC 16 (See Chapter 40 -> Connecting the cable shield)
470
1 /4 W
RX+ 13 5 TX+
220 JUMPER SETTINGS C200H-LK201
1 /4 W
RX- 24 9 TX-
470 Rear-end jumpers Front-end switches
1 /4 W
25 3 GND
GND 7
On - SW3 5 SW4 2
RTS 4 Off Z
CTS 5
15
18

D-Sub D-Sub
Series H
Series CS1
RxD 3 2 TxD CQM1 CPU 21-E and above
TxD 2 3 RxD CVM1 and C200HS/ HE/HG/HX/H (integrated serial)
CPM1 Using interface CPM1-CIF01
GND 7 9 GND
CPM2A/2C
25 4 RTS
RTS 4 5 CTS (RS232)
CTS 5 7 DSR
15 8 DTR
JUMPER SETTINGS CPM1-CIF01
HOST
Max. 15 m.
NT

D-Sub D-Sub
Series H
CQM1 Using interface CQM1-CIF02
RxD 3 2 TxD
TxD 2 3 RxD (RS232)
GND 7 5 GND
25 4 RTS
CTS 5 7 DSR
15 8 DTR
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
CVM1
TX+ 23 8 RX+ (RS422)

220
1/4 W
TX- 12 6 RX-
RX+ 13 2 TX+ (See Chapter 40 -> Connecting the cable shield)
220
1/4 W
RX- 24 1 TX-
25
GND 7
RTS 4
CTS 5
15
18

D-Sub D-Sub
CJ1G
1 SHD (RS232)
RxD 3 2 TxD
TxD 2 3 RxD
GND 7 9 GND
25 4 RTS
RTS 4 5 CTS
CTS 5
15
18
Max. 15 m.
SAIA PLC

D-Sub D-Sub
Series PCD2 / 4
in the programming connector of the CPU (PGU port)
1 SHD
RxD 3 3 TxD (RS232)
TxD 2 2 RxD
RTS 4 8 CTS
CTS 5 6 DSR
GND 7 5 GND
25
15
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-61

D-Sub D-Sub
S-BUS series PCD1 / 2 / 4
in the programming connector of the CPU (PGU port)
1 SHD
RxD 3 3 TxD (RS232)
TxD 2 2 RxD
PLC Address: 0...255
RTS 4 8 CTS
CTS 5 NOTE: Configure the Number of the S-BUS station inside the PLC using the SAIA
programming software.
GND 7 5 GND
25 6 DSR (See Chapter 40 -> Connecting the cable shield)
15
18
Max. 15 m.

D-Sub Terminals
S-BUS series PCD1 / 2 / 4
SHD
Connection to terminal block
VCC 16
470 (RS485)
1/4 W
TxRx+ 22 TxRx+
220 PLC address: 0...255
1/4 W
TxRx- 10 TxRx- SASI 1 (1=first interf., 2=second interf., etc.)
470 999
1/4 W ;TEXT 999 UART:9600,0,0,0;MODE:SS1; DIAG:F260,R500"
GND 7
25 NOTE: Configure the Number of the S-BUS station inside the PLC using the SAIA
RTS 4
programming software.

15
18

D-Sub D-Sub
PCD2 / 4
in the programming connector of the CPU (PGU port) with port initialization
RxD 3 3 TxD
TxD 2 2 RxD (RS232)
GND 7 5 GND
This connection is useful in the event that the PLC does not go in RUN with the
25 VT terminal connected. In this case, you also need to initialize the PGU port with
RTS 4 the instructions:
CTS 5
SASI 0
15 999
18 ; TEXT 999 "UART:9600,7,E,1;MODE:SD0; DIAG:F260,R500"
In this way, if you send the PLC in RUN using the SAIA utility S/W, the ERROR
light switches on, but this is normal. To switch the light off, just remove the instruc-
tion "SASI 0" when the PLC is connected with the utility S/W.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub Terminals
Additional PCD4 interface to BUS
SHD
RxD 3 x0 Tx (RS232)
TxD 2 x1 Rx
NB: To make the terminal function with the additional interface of the SAIA PCD
GND 7 GND
PLC, the following setting must be observed:
25 x2 DTR
RTS 4 x3 DSR SASI 1 (1=first interf., 2=second interf., etc.)
CTS 5
999
x4 RTS
;TEXT 999
15 x5 CTS "UART:9600,7,E,1;MODE:SD0;DIAG:F260,R500;RBUF:255;TBUF:255"
18
VT side (Passive) PLC side Order code:

D-Sub Terminals
Additional PCD4 interface to BUS
SHD
+Rx 18 x0 TS (Current loop)
-Rx 25 x2 TA
+Tx 9 x5 RC
-Tx 11 x7 RG
RTS 4 x4 TC SASI 1 (1=first interf., 2=second interf., etc.)
CTS 5 x6 TG
999
;TEXT 999
x1 RS "UART:9600,7,E,1;MODE:SD0;DIAG:F260,R500;RBUF:255;TBUF:255"
x3 RA
Max. 15 m.
VT side (Passive) PLC side Order code:

D-Sub Terminals
PCD2 serial interface 1 module PCD7/F120
SHD
RxD 3 11 Tx (RS232)
TxD 2 12 Rx
GND 7 10 GND
25
RTS 4 SASI 1 (1=first interf., 2=second interf., etc.)
CTS 5
999
;TEXT 999
15 "UART:9600,7,E,1;MODE:SD0;DIAG:F260,R500;RBUF:255;TBUF:255"
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-63

D-Sub Terminals
Additional PCD4 interface to BUS module BUS C130
SHD
VCC 16 (RS422)
470
1/4 W
Tx+ 23 x3 Rx+
220
1/4 W
Tx- 12 x1 Rx- SASI 1 (1=first interf., 2=second interf., etc.)
470 999
1/4 W ;TEXT 999
GND 7 GND "UART:9600,7,E,1;MODE:SD0;DIAG:F260,R500;RBUF:255;TBUF:255"
25
Rx+ 13 x2 Tx+
220
1/4 W
Rx- 24 x0 Tx-
RTS 4 x4 RTS-
CTS 5 x5 CTS-
15 x6 RTS+
18 x7 CTS+

D-Sub Terminals
SHD
RxD 3 31 Tx (RS232)
TxD 2 32 Rx
GND 7 30 GND
25
RTS 4 SASI 1 (1=first interf., 2=second interf., etc.)
CTS 5
999
;TEXT 999
15 "UART:9600,7,E,1;MODE:SD0;DIAG:F260,R500;RBUF:255;TBUF:255"
18
Max. 15 m.

D-Sub Terminals
SHD
VCC 16 (RS422)
470
1/4 W
B: To make the terminal function with the additional interface of the SAIA PCD
Tx+ 23 14 Rx+
220 PLC, the following setting must be observed:
1/4 W
Tx- 12 13 Rx- SASI 1 (1=first interf., 2=second interf., etc.)
470 999
1/4 W ;TEXT 999
GND 7 "UART:9600,7,E,1;MODE:SD0;DIAG:F260,R500;RBUF:255;TBUF:255"
25
Rx+ 13 12 Tx+
NB: Insert the interface termination resistances (See SAIA manual).
220
Rx- 24 11 Tx-
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub Terminals
SHD
VCC 16 (RS422)
470
1/4 W
B: To make the terminal function with the additional interface of the SAIA PCD
Tx+ 23 39 Rx+
220 PLC, the following setting must be observed:
1/4 W
Tx- 12 38 Rx- SASI 1 (1=first interf., 2=second interf., etc.)
470 999
1/4 W ;TEXT 999
GND 7 "UART:9600,7,E,1;MODE:SD0;DIAG:F260,R500;RBUF:255;TBUF:255"
25
Rx+ 13 37 Tx+ NB: Insert the interface termination resistances (See SAIA manual).
220
Rx- 24 36 Tx-
RTS 4
CTS 5
15
18

D-Sub terminal
PCD2 interface to module TTY - 20mA (PCD7/F130)
SHD
+20mA 14 14 +Rx (Current loop)
+Tx 9 17 -Rx
+20mA 15 13 +Tx
+Rx 18 16 -Tx
GND 7
-Rx 25
-Tx 11
RTS 4
CTS 5
SATT CONTROL PLC

D-Sub D-Sub
Series 31-90
RxD 3 3 TxD (RS232)

TxD 2 2 RxD
GND 7 7 GND PLC serial port configuration:
25
Channel Configuration no.: B
RTS 4 COMLI: C
CTS 5 Master / Slave (M / S): S
Identity (1..247): 1
15
ASCII / Binary (A / B): B
18 Baudrate (110...19200): 9600
Number of data bits: 8
Number of stop bits: 1
Parity (O / E / N): O
Error counters to register (RX/N): N
Max. 15 m. Number of ACIA-errors: 12
Number of BCC-errors: 8
Number of other errors: 4
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-65

D-Sub D-Sub
Series 115
RxD 3 23 TxD (RS232)

TxD 2 24 RxD
GND 7 19 GND Connection to VDU-port.
Possible connection also to PLC PRINTER-port.
25
In this case configure the COMLI 1-port as CHA2 with the appropriate software
RTS 4 programming utility of the PLC
CTS 5
CPLC serial port configuration:
15
18 Channel Configuration no.: B
COMLI: C
Master / Slave (M / S): S
Identity (1..247): 1
ASCII / Binary (A / B): B
Max. 15 m. Baudrate (110...19200): 9600
Number of data bits: 8
Number of stop bits: 1
Parity (O / E / N): O
Error counters to register (RX/N): N
Number of ACIA-errors: 12
Number of BCC-errors: 8
Number of other errors: 4
SCHLEICHER PLC

D-Sub Phoenix
SHD CPU-10, CPU20 serial interface COM2
(RS232)
RxD 3 4 TxD
TxD 2 5 RxD (See Chapter 40 -> Connecting the cable shield)
GND 7 1 Vo
25
RTS 4
CTS 5
15
18
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
Series F
Connection PGU
1 SHD (RS232)
RxD 3 2 TxD
TxD 2 3 RxD N.B: Declare in the PLC program the type of port used.
GND 7 7 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.

D-Sub
Series F
Connection FCS
SHD
(RS422)
TX+ 23 RX+
220
N.B: Declare in the PLC program the type of port used.
1/4 W
TX- 12 RX-
RX+ 13 TX+
220
1/4 W
RX- 24 TX-
25 GND
GND 7
RTS 4
CTS 5
15
18
SIEMENS PLC
VT side (Active) PLC side (Passive) Order code:

D-Sub D-Sub
SIMATIC S5
CPU 90...135
1 SHD FAP CPU 944 / 945
8 SHD
(Current loop - CPU programming port)
+20mA 14 9 +Rx
+Tx 9 2 -Rx (See Chapter 40 -> Connecting the cable shield)
+20mA 15 6 +Tx
+Rx 18 7 -Tx
GND 7
-Rx 25
-Tx 11
RTS 4
CTS 5
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-67

D-Sub D-Sub
SIMATIC S7
16 (RS485)
470
1/4 W SIMATIC S7 200
TxRx+
TxRx+ 22 3
(B) Address of CPU = 1 - 126
220
1/4 W
TxRx- SIMATIC S7 300, S7 400 MPI
TxRx- 10 8
(A)
470 Address of VT: 1...31
1/4 W Address of PLC: 1...31
GND 7
25 To have simultaneous communication between the PLC S7 programming pack-
age and the VT, it is advisable to use the SIEMENS 6ES7972-OBB20-OXAO
RTS 4
passing connector.
CTS 5
15 N.B.: Max. 50m without repeater
18
Max. 50 m.

D-Sub D-Sub
SIMATIC S5
FAP CPU 928B
+20mA 14 13 +Rx module TTY 6ES5 752-0AA12
+Tx 9 14 -Rx
(Current loop)
+20mA 15 10 +Tx
+Rx 18 19 -Tx (See Chapter 40 -> Connecting the cable shield)
GND 7
-Rx 25
-Tx 11
RTS 4
CTS 5
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
#1 SIMATIC S7
(RS485)
6 P5V
470
SIMATIC S7 200
1/4 W
TxRx+ Address of CPU = 1 - 126
TxRx+ 22 3
(B)
220
1/4 W SIMATIC S7 300, S7 400 MPI
TxRx-
TxRx- 10 8 Address of VT: 1...31
(A)
470 Address of PLC: 1...31
1/4 W
GND 7 5 GND
Instead of using a 9 pin connector and integrating the resistances, the following Si-
25 emens connectors can be used with resistances already integrated and insertable
RTS 4 with a sliding switch:
SIEMENS 6ES7972-0BA10-0XA0
CTS 5
SIEMENS 6ES7972-0BA40-0XA0
15 SIEMENS 6GK1500-0EA00
18
For simultaneous communication between the programming package, the PLC S7
and the VT, you are advised to use the following Siemens passing connectors with
resistances already integrated and insertable with a sliding switch:
#n SIEMENS 6ES7972-0BB10-0XA0
SIEMENS 6ES7972-0BB40-0XA0
N.B.: Maximum length without repeater - 50m.
TxRx+ 22 (See Chapter 40 -> Connecting the cable shield)
TxRx- 10
GND 7
25
RTS 4
CTS 5
15
18
#Last
16
470
1/4 W
TxRx+ 22
220
1/4 W
TxRx- 10
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
Max. 50 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-69
SPRECHER+SCHUH PLC

D-Sub D-Sub
(RS232)
RxD 3 2 TxD (See Chapter 40 -> Connecting the cable shield)
TxD 2 3 RxD
CTS 5 4 RTS
RTS 4 5 CTS
GND 7 9 GND
25 10
15 7 DSR
18 8
14 +12V
Max. 15 m.
SQUARE-D PLC

D-Sub D-Sub
Series 400, 500, 600
9 SHD (RS422)
1N4148
Tx 2 3 Rx-
1/4 W
17 4 Rx+
4k7
1/4 W
25
GND 7 2 Tx+
390
1/4 W
Rx 3 1 Tx-
RTS 4 5
CTS 5 6
15 7
18 8

D-Sub FUJITSU
Series 50
In the CPU programming connector
4 SHD (Programmer's Port).
GND 7 8 SHD
(Current loop).
Rx- 25 6 0V
Rx+ 18 2 Rx
IKT 14
RTS 4 7 0V
560
CTS 5
1/4 W
Tx- 11 3 Tx
TX+ 9 1 12Vdc
Soldered 4 3 2 1
end 8 7 6 5
Max. 200 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
TELEMECANIQUE PLC

D-Sub D-Sub
TSX47 UNITELWAY module TSXSCM21
Port Ch.1
16
470 (RS485)
1/4 W
TxRx+ 22 22 TxRx+
Point to point connection.
220
1/4 W
TxRx- 10 12 TxRx- Address of VT: 4...31
470 Address of PLC (N): 0, 4...31
1/4 W Address of PLC module: 0...254
GND 7 25 GND
RTS 4
CTS 5
15
18

D-Sub D-Sub
TSX17/20 using CVPLC1Q102 translator
+20mA 14 6 +Rx (Current loop)

+Tx 9 1 -Rx
+20mA 15 5 +Tx
+Rx 18 9 -Tx
GND 7
-Rx 25
-Tx 11
RTS 4
CTS 5
VT side (Passive) PLC side (Active) Order code:

D-Sub D-Sub
TSX47 - 67 - 87 - 107
5 SHD (Current loop)

-Rx 25 4 TxD+
NOTE: The max length of the cable depends on which version of the Telemeca-
+Rx 18 2 RxD+
nique CPU hardware is being used. With versions of hardware coded lower than
RTS 4 9 +12V V3 (E.g. CPU 47/11, 47/20) the length of the cable is limited to 3 meters given that
CTS 5 8 0V the serial port of the CPU is not optoisolated !!! In this case, whenever you need
to create a cable longer than 3 meters, it is advisable the employ a Telemeca-
-Tx 11 6 TxD-
nique device like XBT Z 9011 or 9012 to guarantee the galvanic isolation of the
+Tx 9 7 RxD- serial line. Failure to adopt such a device can cause damage to the CPUs serial
port !!!
If the CPU is of a hardware version coded higher than V3 (E.g.. CPU 47/411,
47/425 etc.) the max length of the cable relates to the particular characteristics of
See note the interface in Current loop (max 1000 meters) even without employing the
optoisolating device mentioned above, in so far as the CPUs have an internal cir-
cuitry created to guarantee the optoisolation of the line.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-71

D-Sub D-Sub
TSX17 UNITELWAY
16 (RS485)
470
1/4 W Point to point connection.
TxRx+ 22 14 TxRx+
220 220
1/4 W 1/4 W Address of VT: 4...31
TxRx- 10 7 TxRx- Address of PLC (N): 0
470 Address of PLC module: 254
2
1/4 W
GND 7 3 (See Chapter 40 -> Connecting the cable shield)
25 5
RTS 4 9
CTS 5 10
15 11
18 12
15

D-Sub Microdin
TSX07 / 37 / 57 UNITELWAY
Twido (Porta MODBUS)
16
470 (RS485)
1/4 W
TxRx+ 22 7 TxRx+
220 Point to point connection.
1/4 W
470 Address of PLC (N): 0
1/4 W Address of PLC module: 254
GND 7 2 GND
RTS 4
1 4
CTS 5 2 5
7
8
3
15 6
18
Soldered
end

D-Sub D-Sub High Density
TSX47 UNITELWAY
UNITELWAY port
16
470 (RS485)
1/4 W
TxRx+ 22 10 TxRx+
220
Point to point connection.
1/4 W
470 Address of PLC (N): 0
7
1/4 W Address of PLC module: 254
GND 7 9
25 16 (See Chapter 40 -> Connecting the cable shield)
RTS 4 17
CTS 5 18
15 25
18 26
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub
TSX07 ... 87 UNITELWAY
SHD
16 (RS485)
470
1/4 W Point to point connection.
TxRx+ 22 TxRx+
220
1/4 W Address of VT: 4...31
TxRx- 10 TxRx- Address of PLC (N): 0
470 Address of PLC module: 254
1/4 W
GND 7 GND (See Chapter 40 -> Connecting the cable shield)
25
RTS 4
CTS 5
15
18

D-Sub Minidin
#4 TSX07 / 37 UNITELWAY
(RS485)
TxRx+ 22 7 TxRx+
Cable valid for several VTs connected to a single Master PLC.

TxRx- 10 8 TxRx-
GND 7 2 GND Address of VT: 4...31
Address of PLC (N): 0
25
Address of PLC module: 254
RTS 4
CTS 5 4
1
7
15 2 5
8
3
18 6
#n Soldered
end
TxRx+ 22
TxRx- 10
GND 7
25
RTS 4
CTS 5
15
18
#Last
16
470
1/4 W
TxRx+ 22
220
1/4 W
TxRx- 10
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-73

D-Sub D-Sub
#4 TSX17 UNITELWAY
(RS485)
TxRx+ 22 14 TxRx+
220
1/4 W Cable valid for several VTs connected to a single Master PLC.
TxRx- 10 7 TxRx-
GND 7 2 Address of VT: 4...31
Address of PLC (N): 0
25 3
Address of PLC module: 254
RTS 4 5
CTS 5 9 (See Chapter 40 -> Connecting the cable shield)
15 10
18 11
12
15
#n
TxRx+ 22
TxRx- 10
GND 7
25
RTS 4
CTS 5
15
18
#Last
16
470
1/4 W
TxRx+ 22
220
1/4 W
TxRx- 10
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub
#4 TSX07 ... 87 UNITELWAY
SHD
(RS485)
TxRx+ 22 TxRx+
Address of VT: 4...31

TxRx- 10 TxRx- Address of PLC (N): 0, 4...31
GND 7 GND Address of PLC module: 0...254
25
To have more than one PLC in the network, one PLC must be configured as net-
RTS 4 work Master and the others as Slaves.
CTS 5 To be able to configure a PLC as a Slave it is necessary that:
15
In the case of PLCs TSX07 and TSX37 use programming software to param-
18
etrize the PLC as Slave, assigning the chosen address and jump-connecting
pins 2 and 6 on the connector connecting to the network.
#n In the case of PLCs TSX17, TSX47, TSX67 and TSX87 refer to the PLC man-
ual to see which pins to jump-connect on the network connector to assign
TxRx+ 22
the chosen Slave address.

TxRx- 10
GND 7
25
RTS 4
CTS 5
15
18
#Last
16
470
1/4 W
TxRx+ 22
220
1/4 W
TxRx- 10
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
TEXAS INSTRUMENTS PLC

D-Sub D-Sub
Series 400 CPU 435
Series 500 CPU 520 - 530
RxD 3 2 TxD Series 505 CPU 525 - 535
TxD 2 3 RxD
GND 7 7 GND (RS232)
25 4 RTS NB : In the case of CPU 435, set the protocol in ASCII mode (AUX function of
RTS 4 5 CTS TISOFT version 1.2 and upwards).
CTS 5 6 DSR
Connection with module DCM (405 series)
15 20 DTR
18 8 DCD (See Chapter 40 -> Connecting the cable shield)
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-75

D-Sub D-Sub
Series 500 CPU 520 - 530
Series 505 CPU 525 - 535 - 545 (*)
VCC 16
470 (RS422)
1/4 W
Tx+ 23 5 Data IN+
220 (*) Valid only in the case of CPU 545 with hardware version 545-1101. In the case
1/4 W of CPU 545 with hardware version coded higher, see CVPLC06502 cable.
Tx- 12 8 Data IN-
1/4 W
GND 7 6 GND
25
Rx+ 13 1 Data OUT+
220
1/4 W
Rx- 24 7 Data OUT-
RTS 4
CTS 5
15
18

D-Sub D-Sub
Series 400 CPU 435
VCC 16 (RS422)
330
1/4 W
Tx+ 23 9 Data IN+ NB: Set the protocol in ASCII mode (AUX function of TISOFT from version 1.2
100 upwards).
1/4 W
Tx- 12 10 Data IN- (See Chapter 40 -> Connecting the cable shield)
330
1/4 W
GND 7
25
Rx+ 13 14 Data OUT+
150 220
1/4 W 1/4 W
Rx- 24 16 Data OUT-
RTS 4 19 RTS+
CTS 5 11 CTS+
15 18 RTS-
18 23 CTS-

D-Sub D-Sub
Series 505 CPU 545 - 555
RxD 3 3 Xmt (RS232)

TxD 2 2 Rcv
GND 7 5 GND NB: In the case of CPU 555, if connected to port 2, remove the jumper between
pins 7 and 8 on the PLC side.
25 7 RTS
CTS 5 6 DSR
15 4 DTR
18 1 DCD
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

D-Sub D-Sub
Series 505 CPU 545 (*) - 555
VCC 16 (RS422)
470
1/4 W
Tx+ 23 9 Data IN+ (*) Valid only in the case of CPU 545 with hardware versions 545-1102, 545-1103
220 and 545-1104. In the case of CPU 545 with lower hardware version see cable
1/4 W CVPLC06202.
Tx- 12 2 Data IN-
1/4 W
GND 7 5 GND
25
Rx+ 13 3 Data OUT+
220
1/4 W
Rx- 24 8 Data OUT-
RTS 4
CTS 5
15
18
TOSHIBA PLC

D-Sub FUJITSU
(EX 100) CPU M20 - M40
In the CPU programming connector
(Programmer's Port).
+20mA 14 8 +Rx
+Tx 9 3 -Rx (Current loop).
+20mA 15 7 +Tx
+Rx 18 4 -Tx
GND 7
-Rx 25
4 3 2 1
-Tx 11 8 7 6 5
RTS 4
CTS 5 Soldered
end

D-Sub Minidin
Series T1
(RS232)
RxD 3 1 TxD
CTS 5 5 RTS
RTS 4 2 CTS
GND 7 6 GND
25
15 4
1
18
Soldered 2 5
7
end 3
8
6
Max. 15 m.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-77

D-Sub D-Sub
Series T2/T3
(RS232)
RxD 3 3 TxD
CTS 5 7 RTS
RTS 4 8 CTS
GND 7 5 GND
25
15
18
Max. 15 m.
HBM BALANCE SCALES
VT side SCALES side Order code:

D-Sub D-Sub
WE2110
RxD 3 3 TxD (RS232)

TxD 2 2 RxD
GND 7 5 GND
25
RTS 4
CTS 5
15
18
Max. 15 m.
VT side SCALES side Order code:

D-Sub D-Sub
WE2110
16 (RS485)
470 7 RB
1/4 W
TxRx+ 22 9 TB
220
1/4 W
TxRx- 10 6 RA
470
8 TA
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
ASCON THERMOREGULATOR
VT side Thermoreg. side Order code:

D-Sub Terminals
XS-XP-XN-XC-XT-XF
SHD
RxD 3 6 Tx (RS232)
TxD 2 7 Rx
Connection with module ASCON ALS/3/232
GND 7 3 COM
RTS 4
CTS 5
15
18
Max. 15 m.
GEFRAN THERMOREGULATOR

D-Sub Terminals
800/1600/1800
SHD
RxD 3 T+ (RS232)
TxD 2 R+
GND 7 R-
25 T-
RTS 4
CTS 5
15
18
Max. 3,5 m.

D-Sub Terminals
800/1600/1800
SHD
+20mA 14 R+ (Current loop)
+Tx 9 R-
+20mA 15 T+
+Rx 18 T-
GND 7
-Rx 25
-Tx 11
RTS 4
CTS 5
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-79

D-Sub Terminals
800/1600/1800
SHD
(RS422)
TX+ 23 R-
1/4 W
TX- 12 R+
RX+ 13 T-
220
1/4 W
RX- 24 T+
25
GND 7
RTS 4
CTS 5
15
18

D-Sub Terminals
800/1600/1800
SHD
VCC 16 (RS485)
470
Rx-
1/4 W Only applies to protocol of Modbus (Ser.p = 1)
TxRx+ 22 Tx-
220
TxRx- 10 Tx+
470
Rx+
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
HENGSTLER THERMOREGULATOR

D-Sub Terminals
901/906
SHD
VCC 16 (RS485)
470
TxRx+ 22 12 (B+)
220
1/4 W
TxRx- 10 11 (A+)
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40
WEST THERMOREGULATOR

D-Sub Terminals
6100/6600
SHD
VCC 16 (RS485)
470
TxRx+ 22 12 (B+)
220
1/4 W
TxRx- 10 11 (A+)
470
1/4 W
GND 7
25
RTS 4
CTS 5
15
18

D-Sub RJ11
25 pin male 6 pins NOT CODED
MLC9000 Intrabus
SHD
RxD 3 3 Tx (RS232)
TxD 2 2 Rx
25
RTS 4
1
CTS 5 2
3
4
15 5
6
18
Front
View
Max. 15 m.

D-Sub Terminals
MLC9000 Modbus
SHD
16 (RS485)
470
1/4 W
TxRx+ 22 5 A-wire
220
1/4 W
TxRx- 10 4 B-wire
470
1/4 W
GND 7 3 Comm
25
RTS 4
CTS 5
15
18
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-81
Cable The table below lists all the cables mentioned in the chapter together with
information their order codes and a description of the type of device with which it can
summary be used.
Table 40.1: Cable information list (Part 1 of 3)
Producer Code Description RS

ABB CVPLC03102 T200 (KP60) 232
CVPLC14102 CS31 (KR31 / KT31/91/92/93/94/95) T200 (KP62) 232
CVPLC14202 CS31 (KR31 / KT31) RTU MODBUS PROTOCOL 232
CVPLC14302 CS31 (07KP92 R101) RTU MODBUS PROTOCOL 232
CVPLC14602 CS31 (Series 40 & 50) 232
CVPLC21202 AC70 232
CVPLC14802 ACS210 232
CVPLC06402 AC450 232
AEG MODICON CVPLC17102 COMPACT / A120 / A250 232
CVPLC17202 MICRO 232
ALLEN-BRADLEY CVPLC07112 SLC500 CPU 5/02 5/03 485
CVPLC07202 PLC5 /11/20/30/40/40L/60/60L 232
CVPLC07302 PLC5 /11/20/30/40/40L/60/60L 422
CVPLC07402 SLC500 5/03-04-05 Micrologix CPU5550 ControlLogix 232
CVPLC07502 Protection device for DH485 485
CVPLC07602 MICROLOGIX CPU1000, 1200 and 1500 232
ALTUS CVPLC27102 ALNET-1 232
CVPLC27202 ALNET-1 232
ATOS CVPLC29102 MPC1600, MPC2002, MPC4004 232
CVPLC29202 MPC1600, MPC2002, MPC4004 485
BECKHOFF CVPLC28102 BX3100 COM1 Port 232
CVPLC28202 BX3100 COM2 Port 232
CVPLC28302 BX3100 COM2 Port 485
CVPLC28402 KL6001 232
CVPLC28502 KL6021 485
CVPLC28602 BC7300/BK7300 485
BOSCH CVPLC24102 CL150 232
B&R AUTOMATION CVPLC25102 NET2000 232
CONTROL TECHNIQUES CVPLC33102 Commander SE - CTNET 485
CROUZET CVPLC20102 RPX 10-20-30 232
FOXBORO CVPLC30102 RTU20 232
C.L.: Current loop
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 40

FUJI CVPLC26102 Micrex-F F705 422
GE FANUC CVPLC09102 CPU 90-90 MICRO - VERSAMAX PORT 2 422
CVPLC09202 Series 90 - CMM311 PORT1 232
CVPLC09302 Series 90 - CMM311 PORT2 422
CVPLC09402 VERSAMAX PORT1 232
GEFRAN CVPLC23102 Series MPS-NS 232
HITACHI CVPLC03102 H, 02H 232
CVPLC03202 EM CPU CPM - E3 232
CVPLC03302 EC 232
CVPLC03402 H, CPU22-02HC 232
CVPLC03502 Series EH150 232
CVPLC03602 COMM H 422
IDEC IZUMI CVPLC19102 FA2-FA2J C.L.
CVPLC19302 Series MICRO 3 485
KLCKNER MOELLER CVPLC12112 PS306 485
CVPLC12212 PS316 / PS416-CPU400 485
CVPLC12302 PS4-141-MM1 / PS4-201-MM1 / PS4-341-MM1 232
CVPLC12402 PS416-CPU400 232
KEYENCE CVPLC15102 KV10-16-24-40 232
KOYO CVPLC32102 DL 240 CPU Port 232
CVPLC32202 DL 340 CPU Port 232
CVPLC32302 DL 405 DCM, DL 405 CPU Port, DL 305 DCU 232
CVPLC32402 DL 405 DCM, DL 305 DCU 422
CVPLC32502 DL 305 DCU 232
KUHNKE CVPLC07602 KUBES 232
LG CVPLC21102 K30 - K500 - K1000 232
CVPLC21202 K10 232
CVPLC21302 Series MK 485
CVPLC21402 Master K1205 232
CVPLC21502 Master K1205 485
MATSUSHITA-NAIS CVPLC16102 FP-1 422
CVPLC16202 FP-1 / FP-M 232
CVPLC16302 FP-M / FP-0 / FP-2 232
CVPLC16402 FP-3 422
MICROLINK CVPLC31102 ML-14 232
CVPLC31202 ML-14 485
MITSUBISHI CVPLC05102 Series FX 232
CVPLC05202 Series FX 232
C.L.: Current loop
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

40-83

CVPLC05302 Series A + MITSUBISHI SC-05 adaptor 232
CVPLC05402 Series A 232
CVPLC05502 Series Fx0 - Fx0 N - Fx2 N 232
OMRON CVPLC02102 C200H LK201 3G2A6 LK201 EV1 232
CVPLC02202 C20-28-40-60H 232
CVPLC02302 C200H LK202 422
CVPLC02402 Serie H, CQM1, CVM1, Serie CS1, Serie C200H.. 232
CVPLC02502 CQM1CIF02 232
CVPLC02602 CVM1 422
CVPLC02802 CJ1C 232
SAIA CVPLC04102 CPU PCD2/4 232
CVPLC04202 S-BUS CPU PCD1/2/4 232
SATT CONTROL CVPLC18102 Series 31 - 90 232
CVPLC18202 Series 115 232
SCHLEICHER CVPLC08102 CPU-10 / CPU-20 COM2 232
CVPLC08202 Series F connection PGU 232
CVPLC08302 Series F connection FCS 422
SIEMENS CVPLC01202 S5 AG90 ... 135 FAP S5 944/945 C.L.
CVPLC01402 S7 200/300/400 485
CVPLC01502 FAP S5 928B C.L.
SPRECHER+SCHUH CVPLC03102 SPRECHER + SCHUH 232
SQUARE-D CVPLC13102 Series 400 / 500 / 600 422
CVPLC19102 Series 50 C.L.
TELEMECANIQUE CVPLC1Q102 Adaptor PLC TSX17 RS485 - C.L. (Supplied by ESA) C.L.
CVPLC11002 TSX47 UNITELWAY module TSXSCM21 485
CVPLC11102 CVPLC1Q102 C.L.
CVPLC11202 TSX47-67-87-107 C.L.
CVPLC11602 TSX17 UNITELWAY 485
CVPLC11702 TSX07/37/57 UNITELWAY - Twido 485
CVPLC11802 TSX47 UNITELWAY 485
TEXAS INSTRUMENTS CVPLC06102 Series 405-500 232
CVPLC06202 Series 500-505 422
CVPLC06302 Series 400 422
CVPLC06402 Series 505 CPU 545 - 555 PORT 1 232
CVPLC06502 Series 505 CPU 555 PORT 2 422
TOSHIBA CVPLC10102 M20-40-EX C.L.
CVPLC10112 Series T1 232
CVPLC10222 Series T2/T3 232
C.L.: Current loop
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

41-1
Chapter 41 Resistance to chemical substances
Contents Page
Chemical substances 41-2
Cleaning the VT 41-7
Case for terminals VT, H Series 41-7

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 41
41-2 Resistance to chemical substances
All our VTs are built to withstand the effects of the more common chemical
substances encountered in industrial and non-industrial environments. Each
element of the VT that could be exposed to these substances (epoxy coat-
ing, keyboard membrane, screen surface, touch screen and gaskets), is
tested to determine its degree of resistence.
The type of test is not the same for each component but changes according
to the testing authority. Below is an example of a test (carried out by Alca-
tel Bell).
The test procedure was as follows:
A 2 cm ball of cotton wool was immersed in the test substance and then
placed on the keyboard. Two cotton wool balls with different substances
were placed separately on each keyboard; this was then put in a Petri dish
and kept at a temperature of 25C for an hour; after this, the keyboard was
washed in water and dried.
The keyboard was observed and the results classified as follows:

A - No visible deterioration
B - Very slight deterioration
C - Some deterioration
D - Gross damage visible
The substances not appearing in the table were not tested, so there
is no information regarding their effect.
Chemical The table shown below lists all the substances used for the test with their
substances various results.
The table must nevertheless be considered an approximate guide

regard chemical substances: no tests have been carried out on a
completely assembled terminal.
The following table DOES NOT show any test carried out on the
plastic case of terminals VT, H series. For further information, see
Page 41-7
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

41-3
Table 41.1: Chemical resistance data sheet (Part 1 of 5)

Parts of the VT Accessories
Transpar- Resis-
Substance Epoxy Matt
ent key- Touch Protective- Protective 2 tance
powder keyboard Gaskets
board screen 2 glass film
coating 3 surface 2
surface 1
1,1,1-Trichlorethylene NS -- >24h -- >24h -- -- >24h

Acetaldehyde NS -- >24h -- >24h -- -- >24h
10% 3Y -- -- -- -- -- --
Acetic acid 20% 3Y -- -- -- -- -- --
<50% -- >24h -- >24h -- -- >24h
Acetone NS O >24h -- >24h >8h F >24h "
Acetyl NS -- -- -- -- -- E -- "
Acid solutions
LC -- -- -- -- -- E --
HC -- -- -- -- -- F -- "
Ajax NS -- >24h4 -- >24h4 -- -- --
Aliphatic hydrocarbons NS -- >24h -- >24h -- -- >24h
Alkaline solutions
LC -- -- -- -- -- E --
HC -- -- -- -- -- F -- "
NS -- -- -- -- -- E --
<2% -- >24h -- >24h -- -- >24h
Ammonia 5% -- -- -- -- >24h -- --
10% 3Y -- -- -- -- -- --
35% 3Y -- -- -- -- -- --
Ariel NS -- >24h4 -- >24h4 -- -- --
Benzene NS S -- A >24h -- -- >24h "
Benzylalcohol NS -- O -- O -- -- O #
Bichromate NS -- -- -- >24h -- -- >24h
Blown castor oil NS -- -- -- >24h -- -- --
Carbon dioxide NS -- -- -- -- -- E --
Castor oil NS -- >24h -- >24h -- -- >24h
<2% -- >24h -- >24h -- -- >24h
Caustic soda 10% -- -- -- -- >24h -- --
50% -- -- B -- -- -- -- "
Caustic solution CO -- O -- O -- -- O #
Chloric acid NS -- -- A -- -- -- --
Chlorine NS -- -- -- -- -- G -- #
Legend:
A - No visible degradation, B - Very slight degradation, C - Slight degradation, D - Damage visible or gross, E - Unlimited use, F - Limitated use, G - Use inad-
visable, S - The surface melts, X - The surface blisters, O - The surface is destroyed, CO - Concentrated, HC - High concentration, LC - Low concentration,
SA - Saturated, NS - Not specified, h - Hour(s), M - Month(s), Y- Year(s), - All the elements tested resist all the substances, " - At least one of the ele-
ments tested may be damaged by the substances in question, # - All the elements tested may be damaged by the substances in question, -- Not tested.
Notes:
1 - According to Alcatel Bell tests, 2 - According to DIN42115 Parts 2, 3 standards - According to raw material producers, 4 - Tested at 50C
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 41

Transpar- Resis-
coating 3 surface 2
surface 1
Chromic acid
10% 6M -- -- -- -- -- -- "
20% 6M -- -- -- -- -- -- "
Citric acid 5% 3Y -- -- -- -- -- --
Coca Cola NS -- -- A -- -- -- --
Cooking salt solution NS -- -- -- -- -- E --
Copper sulphate 10% 3Y -- -- -- -- -- --
Crude oil NS 3Y -- -- -- -- -- --
Cutting oil NS -- >24h -- >24h -- -- >24h
Cyclohexanol NS -- >24h -- >24h -- -- >24h
Detergent NS -- -- A -- -- -- --
Diesel fuel NS -- >24h A >24h -- -- >24h
Diethyle ether NS -- >24h -- >24h -- -- >24h
Dioxan NS -- >24h -- >24h -- -- >24h
Domestos NS -- >24h4 -- >24h4 -- -- --
Downey NS -- >24h4 -- >24h4 -- -- --
Edible oil NS 3Y -- -- -- -- -- --
Essence of turpentine substitute NS 3Y -- -- -- -- -- --
Ethanol
NS -- -- A >24h >24h E >24h
96% 3Y -- -- -- -- -- --
Ethanol denat. NS 1M -- -- -- -- -- -- "
Ethylacetate NS -- >24h -- >24h -- -- >24h
Ethylene glycol NS O -- A -- -- -- -- "
Fantastic NS -- >24h4 -- >24h4 -- -- --
NS -- -- A -- -- -- --
Formaldehyde
35Vol. 3Y -- -- -- -- -- --
37% -- >24h -- -- -- -- --
42% -- >24h -- -- -- -- --
5% 3Y -- -- -- -- -- --
Formic acid 10% 3Y -- -- -- -- -- --
<50% -- >24h -- >24h -- -- >24h
Formula 409 NS -- >24h4 -- >24h4 -- -- --
Gasoline/petrol NS 3Y -- A >24h >24h F >24h "
Glacial acetic acid NS -- -- -- <1h -- -- <1h "
Legend:
Notes:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

41-5

Transpar- Resis-
coating 3 surface 2
surface 1
Glycerine NS -- >24h -- >24h -- E >24h

Glycol NS -- -- -- -- -- E --
Grape juice NS -- >24h4 -- >24h4 -- -- --
Gumption NS -- >24h4 -- >24h4 -- -- --
High pressure steam (at >100C) NS -- O -- O -- G O #
Hydraulic fluids NS -- -- -- -- -- F -- "
<10% -- >24h -- >24h -- G >24h "
Hydrochloric acid 10% 3Y -- -- -- -- -- --
20% 3Y -- -- -- -- -- --
<25% -- -- -- >24h -- -- >24h
Hydrogen peroxide 30% -- -- A -- -- -- --
40Vol. 6M -- -- -- -- -- -- "
Isopropanol NS S >24h A >24h -- -- >24h "
Jet Dry NS -- >24h4 -- >24h4 -- -- --
Lactic acid 5% 3Y -- -- -- -- -- --
Lemon juice NS -- B 4 -- B 4 -- -- -- "
Lenor NS -- >24h 4 -- >24h 4 -- -- >24h
Linseed oil NS 3Y >24h -- >24h -- -- >24h
Liquid allum NS -- -- -- -- -- E --
Methane NS -- -- -- -- -- F >24h "
Methanol NS -- >24h A >24h -- F -- "
Methyl ethyl ketone NS -- >24h -- >24h -- -- >24h
Methylene Chloride NS 1M O -- O -- G O #
Milk NS -- >24h 4 -- >24h 4 -- -- --
Mineral acids CO -- O -- O -- -- O #
Mineral oil 0-180 NS -- -- A -- -- E --
Mustard NS -- >24h4 -- >24h4 -- -- --
n-Butanol NS S -- -- -- -- -- -- "
Nitrate of ammonia SA 3Y -- -- -- -- -- --
<10% -- >24h D >24h -- G >24h "
Nitric acid
10% 3Y -- -- -- -- -- --
20% 3Y -- -- -- -- -- --
50% 1M -- -- -- -- -- -- "
Legend:
Notes:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 41

Transpar- Resis-
coating 3 surface 2
surface 1
Nitrocellulose solvents NS -- -- -- -- -- G -- #
Oil NS -- -- -- -- -- E --
Oleic acid NS 3Y -- -- -- -- -- --
Paraffin oil NS 3Y >24h -- >24h -- -- >24h
Perchloroethylene NS -- -- -- >24h -- G >24h "
Persil NS -- >24h4 -- >24h4 -- -- --
10% 3Y -- -- -- -- -- --
Phosphoric acid
20% 3Y -- -- -- -- -- --
50% 3Y -- -- -- -- -- --
<30% -- >24h -- >24h -- -- >24h
Photographic chemicals NS -- -- -- -- -- E --
Potassium carbonate NS -- >24h -- >24h -- -- >24h
Potassium ferrocyanide NS -- >24h -- >24h -- -- >24h
Potassium hydroxide
10% 3Y -- -- -- -- -- --
20% 3Y -- -- -- -- -- --
Sea water NS -- -- -- -- -- E --
Sebacic acid SA 3Y -- -- -- -- -- --
Silicon grease NS -- -- -- -- -- E --
Silicon oil NS -- -- -- >24h -- E >24h
Skydrol NS 6M -- -- -- -- -- -- "
Sodium carbonate SA -- >24h -- -- -- -- --
Sodium chloride 3% 3Y -- -- -- -- -- --
Sodium hydroxide 20% 3Y -- -- -- -- -- --
NS -- >24h -- -- -- -- --
Sodium hypochloride 10% 6M >24h -- -- -- -- -- "
<20% -- -- -- >24h -- -- >24h
Softner NS -- >24h -- >24h -- -- --
<10% -- -- -- -- -- -- >24h
10% 3Y -- -- >24h >24h -- --
Sulphuric acid 28% 3Y -- A -- -- -- --
50% 6M -- -- -- -- -- -- "
CO -- -- -- -- -- G -- #
Tartaric acid SA 3Y -- -- -- -- -- --
Legend:
Notes:
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

41-7

Transpar- Resis-
coating 3 surface 2
surface 1
Teepol NS 3Y -- -- -- -- -- --
Toluene NS 3Y >24h A >24h -- G >24h "
Tomato juice NS -- B4 -- B4 -- -- -- "
Tomato sauce NS -- B4 -- B4 -- -- -- "
Top Job NS -- >24h4 -- >24h4 -- -- --
Trichloroethylene NS S -- -- >24h -- G >24h "
Turpentine oil NS -- >24h -- -- -- F -- "
Turpentine substitute NS -- -- -- >24h -- -- >24h
Vaselline NS -- -- -- -- -- F -- "
Vim NS -- >24h4 -- >24h4 -- -- --
Vinegar NS -- -- D -- -- -- -- #
Vortex NS -- >24h4 -- >24h4 -- -- --
Washing powders NS -- >24h -- >24h -- E >24h
Water NS -- >24h -- -- -- E --
White spirit NS 3Y -- A -- -- -- --
Windex NS -- >24h 4 -- >24h 4 -- -- --
Wisk NS -- >24h 4 -- >24h 4 -- -- --
Wood oil NS -- -- -- -- -- F -- "
Xilene NS 1Y >24h -- >24h -- -- --
Legend:
Notes:
Cleaning the For cleaning the VT we recommend Denaturalised Ethyl Alcohol. Should
VT this be insufficient for removing the impurity making it necessary to use
other products, consult the tables above.
This information DOES NOT apply for terminals VT, H series.

Use water instead of alcohol, or non aggressive detergents.
Case for The producer of the raw materials used to manufacture the case does not
terminals VT, supply detailed information regarding the tests performed and the concen-
H Series tration of substances used during the tests. The information below is the
suppliers original text.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 41
Chemical resistance of certain material is dependent on the environmental

conditions where the material is actually used. Therefore, it should be
understood that the various usage parameters involved in and actual appli-
cations, e.g., chemical exposure duration, chemical type, loading, service
temperature, stress, outdoor exposure, etc., may alter the performance sig-
nificantly. Another important factor affecting the chemical resistance is the
type of thermoplastic resin. Amorphous polymers tend to be more suscep-
tible to chemical attack than crystalline polymers.
Rresins are generally stable to water, weak acid and mineral oil. Mechani-
cal properties and surface appearance, however,can be deteriorated if a
molded part is exposed to hot water, strong acid, alkalis, Ketones and aro-
matic hydrocarbons, etc.
Chemical Effect
Stable under common conditions of

Acids
concentration and temperature.
Stable at low concentration.

Alcohols Unstable at high concentration and
elevated temperature.
Stable at low concentration.
Alkalis Unstable at high concentration and
elevated temperature.
Stable except strong alkaline materi-

Detergents and Cleaner
als.
Aromatic Hydrocarbons Solvents should not be used.
Ketons, Toluene, Xylene Cause severe damage.
Silicon oil Stable.
Make sure the plastic shell does not come into contact with any
oils containing paraffin clorurate or active nitrogen. These sub-
stances may change the mechanical qualities of the product.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

42-1
Chapter 42 Technical support
Contents Page
International Customer Care 42-2
International Product Returns 42-2

This chapter consists of a total of 4 pages.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

CHAPTER 42
42-2 Technical support
International The International Customer Care service can be contacted by:

Customer
Care
Telephone:++39-031757400
Fax: ++39-031751777
E-Mail: [email protected]
Web site: http://www.esahmi.com
International Should it be necessary to return the VT terminal for repair:

Product
Returns Contact our International Customer Care service to authorize the return.
Fill in all parts of the form to accompany the product.
Our International Customer Care service will supply all the necessary infor-
mation for returning a an item.
!!! IMPORTANT NOTE !!!
ESA elettronica S.p.A. will accept:

goods carriage free / freight prepaid (transport at customers cost).
goods carriage forward / freight collect (transport paid by ESA) only
with the prior authorization of the company.
ESA elettronica S.p.A. will reject:

any returned goods carriage forward where there has been no prior
authorization.
It is not necessary to send connectors, cables and accessories (unless

they are thought to be linked to the problem indicated).
Thank you for your kind co-operation.
405.1200.037.2 - Rel.: 2.20 of 26/03/2007

REPAIRS RETURN FORM
NOTE: Please complete form in BLOCK CAPITALS.
Product: .............................................. S/N:

Customer details (must be filled in)
Compiled by : ...............................................................................................................
Company : ...............................................................................................................
Full address : ...................................................................... Post Code: .....................
Town : ................................................. County: ...........................................
Tel. no. : .................................................. Fax: ...................................................
Contact person (where different from above)
Name : .................................................................................................................
Tel. no. : .................................................. Fax: ...................................................
Information regarding problem (must be filled in)
Device connected: ...............................................................................................

Detailed description of the problem and the circumstances under which it occurs:
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
Notes: ..........................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
Customer Care worker contacted: ............................................................................
Date of compilation: ...../...../........ Signature: ...............................................................

Hardware Manual - Rel 2 - 20

Uploaded by

Copyright:

Available Formats

Hardware Manual - Rel 2 - 20

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hardware Manual - Rel 2 - 20

Uploaded by

Copyright:

Available Formats

VTWIN

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

All products referred to are covered by the appropri-

electromagnetic compatibility (EMC):

emissions EN 61000-6-4 (2001)

and thus are in line with:

Video terminals VT50 and VT60 have also obtained:

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

Table 0.1: Tests carried out for CE-mark.

Tests carried out for RINA approval

Publication IEC 68-2-6 (1982) Fc. test (Vibration)

Any modification made to the product in its original form as sold

The simple application of an adhesive on any part of the terminal

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

General Safety Precautions

System The System should be designed to prevent equipment malfunction due to

Redundant failsafe system design should be used in order to ensure

The VT is not suitable for applications such as medical life support

Do not install the VT in an ambient temperature exceeding the allowed

Do not limit the VTs rear-face ventilation, in order to avoid component

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

Do not use the VT in excessively dirty or dusty environmental condi-

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

Foreword The manual ................................................................... F-1

Introduction What is a Video Terminal .............................................. I-1

Essential information Graphic terminals.................................................................. E-1

General information on Contents........................................................................ 1-1

Power Supply Contents........................................................................ 2-1

Video terminal VT50 Contents........................................................................ 3-1

Video terminal VT60 Contents........................................................................ 4-1

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

Accessories .......................................................................... 4-12

Video terminal Contents........................................................................ 5-1

Video terminal Contents........................................................................ 6-1

Video terminal Contents........................................................................ 7-1

Video terminal Contents........................................................................ 8-1

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

Functions ...................................................................... 8-4

Video terminal Contents........................................................................ 9-1

Video terminal Contents........................................................................ 10-1

Video terminal Contents........................................................................ 11-1

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

Improving display color quality ............................................. 11-19

Video terminal Contents........................................................................ 12-1

Video terminal Contents........................................................................ 13-1

Video terminal Contents........................................................................ 14-1

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

Video terminal VT505H Contents........................................................................ 15-1

Video terminal Contents........................................................................ 16-1

Video terminal Contents........................................................................ 17-1

Video terminal VT525H Contents........................................................................ 18-1

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

Technical characteristics............................................... 18-2

Video terminal Contents........................................................................ 19-1

Video terminal Contents........................................................................ 20-1

Video terminal Contents........................................................................ 21-1

405.1200.037.2 - Rel.: 2.20 of 26/03/2007

Functions ...................................................................... 21-4

Video terminal Contents........................................................................ 22-1