Layout: Model Space and Paper Space

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

Layout

Display one or more scaled views of your design on a standard-size drawing sheet called a layout.

After you finish creating a model at full size, you switch to a paper space layout, where you can create scaled
views of the model, and you can add notes, labels, and dimensions. You can also specify different linetypes
and line widths.

Model Space and Paper Space


As you know, you create the geometry of your model in model space.

Originally, this was the only space available in AutoCAD. As a result, all notes, labels, dimensions, and the
drawing border and title block were also created in model space.
After paper space was introduced, you could click a layout tab to access a space designed specifically for
layouts and scaling. In the following illustration, paper space is active. There are currently only two objects in
paper space: a drawing border block, and a single layout viewport, which displays a view of model space.

Working with layout viewports is described in more detail later in this topic.

Four Methods for Scaling


There are four different methods in AutoCAD that are used to scale views, notes, labels, and dimensions. Each
method has its advantages depending on how the drawing will be used. Here is a brief summary of each of the
methods:
The Original Method. You create geometry, annotate, and print from model space. Dimensions, notes, and
labels must all be scaled in reverse. You set the dimension scale to the inverse of the plot scale. With this
method, scaling requires a little math. For example, a common scale used in architecture is 1/4" = 1'-0" which is
1:48 scale. If a note is to be printed " high, then it must be created 48 times as large, or 12" high in model
space. The same scale factor also applies to dimensions, and an ARCH D drawing border at that scale is 144
feet long. When the drawing is printed as a D-size sheet, everything scales down to the correct size.
NoteMany AutoCAD drawings were created with this method, and many companies still use it. Once everything
is set up, the method works well for 2D drawings with single views and inserted details.

autodesk Page 1
is set up, the method works well for 2D drawings with single views and inserted details.
The Layout Method. You create geometry and annotate in model space, and print from the layout. Set the
dimension scale to 0 and the dimensions will scale automatically.
The Annotative Method. You create geometry in model space, create annotative dimensions, notes, and labels
(using a special annotative style) in model space from the layout, and you print from the layout. Annotative
objects display only in layout viewports that share the same scale. The dimension scale is automatically set to
0 and all annotative objects scale automatically.
The Trans-Spatial Method. You create geometry in model space, create annotations in paper space on a layout
with dimension scale set to 1, and you print from the layout. This is arguably the easiest, most direct method,
and it is the method of choice for this guide.
Talk to other AutoCAD users in your discipline about these four methods and why they chose the method that
they use.

Specifying the Paper Size of a Layout


The first thing that you should do when you access a layout tab is right-click the tab and rename it to something
more specific than Layout 1. For a D-size layout, ARCH D or ANSI D might be good choices.

Next, open the Page Setup Manager to change the paper size displayed in the layout tab.

NoteYou might be wondering why there are two entries in the list for every sheet size. This is because some
printers and plotters do not recognize the drawing orientation setting.

Layout Viewports
A layout viewport is an object that is created in paper space to display a scaled view of model space. You can
think of it as a closed-circuit TV monitor that displays part of model space. In the illustration, model space is
active and accessible from within the current layout viewport.

autodesk Page 2
active and accessible from within the current layout viewport.

In a layout, when model space is active, you can pan and zoom, and do everything else just as if you were on
the Model tab.
ImportantYou can switch between paper space and model space by double-clicking inside and outside the
layout viewport.
Here is an example of how you would use paper space. In the illustrations below, you created a backyard deck
design in model space, and now you want to lay out and print your design from a layout tab.

The view in the layout viewport is not yet set to the correct scale.
NoteYou can use the MVIEW (make view) command to create additional layout viewports in paper space. With
several layout viewports, you can display several views of model space.

Scaling Views and Trans-Spatial Annotation


Here are the steps that you might follow if you use the trans-spatial method of annotating your drawing:

1. You click the layout tab. If you started the drawing with your own custom drawing template file, several tasks
might already have been completed: the layout might already be set to D-size, and the title block might already
have been inserted in the layout.

2. By default, paper space is active, so you double-click within the layout viewport to make model space active.
Notice that the edge of the layout viewport becomes thicker as a result of switching to model space.

3. You zoom out and center the model space view by panning. However the displayed view is still not set to the
correct scale.

4. You double-click outside the layout viewport to make paper space active again.

5. You open the Properties palette and then click to select the edge of the layout viewport.

autodesk Page 3
6. In the Properties palette, you specify a standard scale of 1/4" = 1'-0" from the drop-down list. This action scales
your view of model space precisely to the D-size drawing. You also set the Display Locked property from No to
Yes. This prevents any unintentional changes to the displayed view.

NoteBy default, the dashes and spaces in a non-continuous linetype appear at the same length regardless of
the scale of the layout viewport.

7. You then might want to move the layout viewport a little and adjust its edges using grips.

8. You create notes, labels, and dimensions directly in paper space. They automatically appear at the correct
size.

9. You turn off the layer on which you created the layout viewport object. This hides the edges of the layout
viewport as shown below.

10. You print the drawing.


NoteAfter you have finished dimensioning, you can use the EXPORTLAYOUT command to merge everything
in paper space and model space into the model space of a separate drawing file. This operation creates a
drawing file that conforms to the original method of creating the model and all annotations in model space.

autodesk Page 4

You might also like