Mill Operation Manual en 1

SYNTEC
Mill Controller Manual
By: SYNTEC
Date: 2010/4/20
Version: 8.3
Version edit record
No. Modify Content date editor New Vision
01
02 Modify teach-in operation 2007/03/20 Jerry_Lai V8.1
03 Modify auto center and auto tool 2008/08/12 Samuel _Chen V8.2
04 Modify graph and sync. with Chinese version 2010/04/20 Samuel _Chen V8.3
Contents
1 CNC MILLING CONTROLLER INTERFACE ................................................ 1
1.1 CNC System Configuration............................................................................ 1
1.2 Screen Sections .............................................................................................. 2
1.3 Main Menu Selections ................................................................................... 3

1.3.1 F1Position .............................................................................................. 4
1.3.1.1 F1Coor. Switch .............................................................................. 5
1.3.1.2 F21/2 Coor. .................................................................................... 5
1.3.1.3 F3Clear Coor. ................................................................................. 5
1.3.1.4 F4Clear All Relative ....................................................................... 6
1.3.1.5 F5Workpiece Coor. ........................................................................ 6
1.3.1.5.1 F1Coor. Latched ......................................................................... 7
1.3.1.5.2 F2Rel. Latched ........................................................................... 7
1.3.1.5.3 F3Aux. Latched .......................................................................... 7
1.3.1.5.4 F5Middle Point Func. ................................................................. 7
1.3.1.5.5 F6Tool Tip Measure ................................................................... 7
1.3.2 F2Program ............................................................................................. 8
1.3.2.1 F1Insert Cycle ................................................................................ 9
1.3.2.2 F2Delete Line ................................................................................. 9
1.3.2.3 F3Edit Cycle .................................................................................10
1.3.2.4 F5EDIT .........................................................................................11
1.3.2.4.1 EDIT sub function F1 : Search ...................................................12
1.3.2.4.2 EDIT sub function F2 : Replace .................................................13
1.3.2.4.3 EDIT sub function F3 : Go To Line ..........................................14
1.3.2.4.4 EDIT sub function F4: copy line ...............................................14
1.3.2.4.5 EDIT sub function F5: Insert line .............................................14
1.3.2.5 F6Teach ........................................................................................15
1.3.2.5.1 F1Rapid Teach ..........................................................................15
1.3.2.5.2 F2Line Teach.............................................................................15
1.3.2.5.3 F3Arc Teach ..............................................................................15
1.3.2.5.4 F4Cancel Middle .......................................................................16
1.3.2.5.5 F5Radius Teach .........................................................................16
1.3.2.5.6 F6Delete Line ............................................................................16
1.3.2.5.7 F7Coord Switch .........................................................................16
1.3.2.5.8 F8Point Teach ...........................................................................16
1.3.2.6 F7Simulation .................................................................................17
1.3.2.6.1 F1 STEP ...................................................................................17
1.3.2.6.2 F2Continue ................................................................................17
1.3.2.6.3 F3Zoom .....................................................................................18
1.3.2.6.4 F5Graph reset ............................................................................18
1.3.2.6.5 F6Abort .....................................................................................18
1.3.2.6.6 F8Simu. Setting .........................................................................18
1.3.2.7 F8File Manager .............................................................................20
1.3.2.7.1 F1New File ................................................................................21
1.3.2.7.2 F2Copy File ...............................................................................21
1.3.2.7.3 F3Delete File .............................................................................21
1.3.2.7.4 F4Import ...................................................................................22
1.3.2.7.5 F5Export ...................................................................................23
1.3.2.7.6 F6RS232 Import ........................................................................24
1.3.2.7.7 F7 RS232 Export ...........................................................................25
1.3.2.7.8 RS232 communication parameter setting .......................................26
1.3.3 F3DlgInput (ONLY for 940M) ..............................................................27
1.3.4 F4Monitor .............................................................................................27
1.3.4.1 F1Coor ..........................................................................................27
1.3.4.2 F2Graph Adjust .............................................................................28
1.3.4.2.1 F1Zoom .....................................................................................28
1.3.4.2.2 F2Graph Reset ...........................................................................28
1.3.4.2.3 F5Simu Setting ..........................................................................28
1.3.4.3 F3MDI Input .................................................................................29
1.3.4.4 F4SETTING ..................................................................................30
1.3.4.5 F5Tool Setting ...............................................................................31
1.3.4.6 F8Work Record .............................................................................32
1.3.5 F5Alarm................................................................................................33
1.3.5.1 F1Actual........................................................................................34
1.3.5.2 F2History ......................................................................................34
1.3.5.3 F5: Save ............................................................................................34
1.3.6 F6Parameter ..........................................................................................35
1.3.7 F7Diagnosis ..........................................................................................36
1.3.7.1 F1PLC State ..................................................................................37
1.3.7.2 F2System Data ..............................................................................38
1.3.7.3 F3Global Variable .........................................................................39
1.3.7.4 F4Coord Variable ..........................................................................40
1.3.7.5 F8System Manager ........................................................................41
1.3.8 F8Guidance ...........................................................................................42
2 MACHINE OPERATION PANEL ...................................................................43
2.1 2nd machine operation panel ..........................................................................43

2.1.1 POWER ON .............................................................................................43
2.1.2 POWER OFF ............................................................................................43
2.1.3 Emergency STOP......................................................................................43
2.1.4 Home mode and Home function ................................................................43
2.1.5 Continues JOG (Rapid JOG) .....................................................................43
2.1.6 Incremental JOG .......................................................................................44
2.1.7 MPG JOG .................................................................................................44
2.1.8 AUTO mode NC file execute ....................................................................44
2.1.9 MDI mode single block execute ................................................................44
2.1.10 MPG Simulation ...................................................................................45
2.1.11 Dry Run ................................................................................................45
2.1.12 Single block ..........................................................................................45
2.1.13 Option Stop ...........................................................................................46
2.1.14 Option Skip ...........................................................................................46
2.1.15 Spindle control ......................................................................................46
2.1.16 Working led ..........................................................................................47
2.1.17 Working Liquid .....................................................................................47
2.1.18 Aux table backward...............................................................................47
2.1.19 Aux table forward .................................................................................47
2.2 Text key description:.....................................................................................48
3 HOW TO OPERATE SYNTEC 900ME ...........................................................50
3.1 Manual function (JOG, INC_JOG, MPG) .....................................................51
3.2 HOME ..........................................................................................................52
3.3 Open a file (EDIT / FLOPPY / RS232) .........................................................53
3.4 Tool setting (G40/G41/G42, G43/G44/G49) .................................................54
3.5 Tool Length measurement (G43/G44/G49) ...................................................55
3.6 Setting the Workpiece origin offset value (G54...G59) ..................................56

3.7 Manual Data Input (MDI) .............................................................................57
3.8 Assigned an executing NC file (AUTO) ........................................................58
3.9 Graphic Simulation .......................................................................................59
3.10 How to check NC file in SYNTEC controller ................................................60
3.11 Auto Center ..................................................................................................61

3.11.1 Manual Center.......................................................................................61
3.11.2 Auto center operation ............................................................................63
3.12 Z-axis Auto Tool...........................................................................................65
3.13 RS232 FUNCTION ......................................................................................70
3.14 DNC Function ..............................................................................................72
3.15 The software of SYNTEC controller replace the software of DNC to execute
RS232 function............................................................................................................
.....................................................................................................................74
1. CNC Milling Controller Interface
1 CNC Milling Controller Interface

1.1 CNC System Configuration
CNC Mill
Position Program Dlginput Monitor Alarm Param. Diagnosis Guidance

F1 F2 F3 F4 F5 F6 F7 F8
Coor Insert Cycle Coor Actual System Param PLC State
1/2 Coor Delete Line Graph Adjust History Go to page One

PLC I Bit
Clear Coor Edit Cycle MDI Input Save Operation Setting
PLC O Bit
All Clear Relative Edit Setting
PLC C Bit
Workpiece Coor Tool setting
Search PLC S Bit
Work Record
Replace PLC A Bit
Go To Line PLC Register
Copy Line PLC Timer
Insert Line PLC Counter
Teach System Data
Global Data
Rapid Teach
System Manger
Line Teach
Arc Teach Software Setup
Cancel Middle Backup System
Delete Line Install Local L.
Simu. Store Language
Step
Continue
Zoom
Graph Reset
Abort
Simu. Setting
File Manager
New File
Copy File
Delete File
Import
Export
RS232 Import
RS232 Export
-1-
1.2 Screen Sections

The screen of controller is shown as followings:
Start
1 2 3 4
Screen
5
7
6
(8)
Meanings For Fields on the Display:

1Program Number
2Title
3Time
4Date
5Data Input
6Hint
7Status
8Function Key Switch
-2-
1.3 Main Menu Selections

The following diagram is the main menu selections for SNC Mill
controller. To operate SNC Milling controller, users simply make the
selections by pressing function keys, F1F8 located on the bottom of the
screen.
-3-
1.3.1 F1Position
This selection displays coordinate settings of current position. It can
also be used to reset the position of relative coordinate. Pressing function
key, F1, under the main menu to enter this selection (NoteThis is the first
screen when the system is booted up)
Meaning of fields on the display------

XX axis coordinate.
YY axis coordinate.
ZZ axis coordinate.
FeedrateFeedrate of cutting tool at each machining, mm per minute
(mm/min).
SpindleRPM of spindle speed.
Machine(Relative coordinate of working platform)
The current position of cutting tool relative to working platform is
shown as machine coordinate on the display.
Relative
The current position of cutting tool relate to the previous location.
Absolute(Programming Coordinate)
The current position of the origin of user defined coordinate is shown
as an absolute position on the display.
Distance To GoThe distance of the cutting tool that need to move to
the next position show on position(+) and negative(-) direction.
-4-
Function key selections

1.3.1.1 F1Coor. Switch
FunctionSwitch Coordinate Display
OperationUnder the Position submenu, whenever users press F1 key,
the values and coordinate on the left corner of the display will toggle
among the four different coordinates with bigger fonts as shown in the
following figure:
1.3.1.2 F21/2 Coor.

Function: Set the center point of work piece as coordinate origin.
Operation: Under the Position submenu, when the message line shows
X Input(or Y Input or Z Input), press F2 1/2 Coordinating and
the origin of the coordinate will move to the center point of work
piece.
1.3.1.3 F3Clear Coor.

FunctionReset the value of X(or Y or Z) axis relative coordinate to
zero. (No effect on other axes)
OperationUnder the Position submenu, when the message line shows
X Input(or Y Input or Z Input), press F3 to reset the value of
X(or Y or Z) axis relative coordinate to zero.
-5-
1.3.1.4 F4Clear All Relative

FunctionReset XYZ relative coordinate to zero.(No effect on other
coordinates)
Operation Under the Position submenu, pressing F4 will reset XYZ
relative coordinate to zero.
1.3.1.5 F5Workpiece Coor.

FunctionRelative to machine coordinate setting for G54~G59.
OperationUnder the Position submenu, press "F5" key and the
following screen will show up. The users can begin to set the auto
machine coordinate settings of G54~G59. (The system needs to be in
Ready Status)
1. External Shift : operator can set the all coordinate
G54..G59 at the same time .
2. CNC default G54 ,if user dont set any G54..G59 in the NC
file
-6-
1.3.1.5.1 F1Coor. Latched

Set the current machine coordinate to the input box
1.3.1.5.2 F2Rel. Latched

Set the current relative coordinate to the input box
1.3.1.5.3 F3Aux. Latched

Set the current relative coordinate to the input box
1.3.1.5.4 F5Middle Point Func.
1.3.1.5.5 F6Tool Tip Measure
-7-
1.3.2 F2Program
This selection provides users with program file management and
editing. With a full screen editor, users can use arrow keys
to move the cursor to anywhere on the screen for editing purpose. Press F2
under the main menu to enter this selection. The full screen editor is shown
as follows:
-8-
Program Sub menu Key Selections:

1.3.2.1 F1Insert Cycle
FunctionInsert a block or cycle by conversation
OperationUnder Program submenu, press F1 to insert a line or cycle
before cursor position.(See Graphic Input Interface(900ME) User
Guide)
1.3.2.2 F2Delete Line

FunctionDelete a line at cursor position.
operation: Under Program submenu, press F2 to delete a line where the
cursor is located.
-9-
1.3.2.3 F3Edit Cycle

FunctionEdit an old block or cycle by conversation input
Operation: Under Program submenu, press F3 to edit a line where the
cursor is located.
-10-
1.3.2.4 F5EDIT
Function : Edit sub function Search Replace Goto line Copy
line Insert line
Operation : User can use this menu for more edit sub function
-11-
1.3.2.4.1 EDIT sub function F1 : Search

FunctionSearch String
OperationUnder Program submenu, press F5EDIT and then
F1 Search to search string. An dialog box will pop up asking
users to input a string as shown in the following figure. After
keying in a string, press F1 to start searching.
-12-
1.3.2.4.2 EDIT sub function F2 : Replace

FunctionReplace String.
OperationUnder Program submenu, press F5 EDIT and then
F2Replace to replace string. An dialog box will pop up asking
users to input the replacing string and the new string as shown in
the following figure. After keying in a string, press F1 to start
replacing.
-13-
1.3.2.4.3 EDIT sub function F3 : Go To Line

FunctionGo to a line number
Operation Under Program submenu, press F4EDIT and then
F3GOTO line to go to the line number. A dialog box will pop up
asking users to input a line number. After keying in a number, press
F1 to go to the desired line.
1.3.2.4.4 EDIT sub function F4: copy line

FunctionCopy a line from current cursor to next line
F4Copy line to go to the next line.
1.3.2.4.5 EDIT sub function F5: Insert line

FunctionInsert a space line above current cursor line
F5Insert line to Insert a new space line
-14-
1.3.2.5 F6Teach
Function: Teach present absolute coordinate to NC files
OperationUnder Program submenu, press F6Teach
Teach sub Key Selections

1.3.2.5.1 F1Rapid Teach
Function: Add G00 code to NC files, G00 to current absolute
coordinate,
1.3.2.5.2 F2Line Teach

Function: Add G01 code to NC files, G01 to current absolute
coordinate,
1.3.2.5.3 F3Arc Teach

Function: Add G02 or G03 code to NC files
1. 1st time press this key arc teach ,CNC auto put current
value to Arc middle point
2. 2nd time press this key arc teach ,CNC auto calculate
G02 or G03 ,and filled the complete code to NC files
-15-
1.3.2.5.4 F4Cancel Middle

Function: When arc teach ,user can use this key to abort middle
point teach .
1.3.2.5.5 F5Radius Teach

Function: Add G02 or G03 code to NC files by G_code menu
and Arc Radius
1.3.2.5.6 F6Delete Line

Function: When user use Teach function , user can use this key
Delete line to delete line
1.3.2.5.7 F7Coord Switch

Function: When the number of axis is more than 4-axis ,user can
use this key to switch absolute coordinate of other axis.
1.3.2.5.8 F8Point Teach

Function: Add current absolute coordinate to NC files.
-16-
1.3.2.6 F7Simulation
Function: Simulating the workpiece program can prove the accuracy of
the editing program.
OperationUnder Program submenu, press F7
F7 simulation sub Key Selections

1.3.2.6.1 F1 STEP
Function: To simulate NC files STEP by STEP
Operation: Under Program submenu, press F7Simulation and
then F1Step .The operator can use this function ,to check NC
file STEP by STEP
1.3.2.6.2 F2Continue
Function: To simulation NC file one time .
Operation: Under Program submenu, press F7 Simulation and
then F2Continue .The operator can use this function to check
NC file whole picture ,when push button.
-17-
1.3.2.6.3 F3Zoom
Function: To enlarge the workpiece graph.
Operation: Under Program submenu, press F7 and then F3.The
operator can use the ,,, cursor to move the frame
to the determined area. And use PageUp PageDn to Enlarge
this area .
1.3.2.6.4 F5Graph reset

Function: To recover the zoomed workpiece graph.
1.3.2.6.5 F6Abort
Function: To abort simulation action
1.3.2.6.6 F8Simu. Setting

Function: To set simulation parameter
Simulation Parameter description :

Path color : User can select cutting path color by this parameter
Cursor color : User can select cutting point color by this
parameter
Drawing mode : User can select simulation plane by this
parameter
Vertical / Horizontal angle : when XYZ drawing mode ,user can
select 3D View angle by these 2 parameter
Window range :
-18-
Mode (0: simulation ,1: direct draw)

0 : When operator change his main screen to
F4Monitor ,CNC would automatically simulation at that
screen
1 : When operator change his main screen to
F4Monitor ,CNC would not simulation at that screen but
direct drawing the cutting cursor .
Xmin/Xmax, Ymin/Ymax ,Zmin/Zmax :

When direct draw mode ,operator must set draw window by these
parameter ,the best way : after simulation use simulation result which is
located at the top of this screen to X,Y,Z range .
-19-
1.3.2.7 F8File Manager

Under Program submenu, press F5 and the following diagram will
show up. Users can use arrow keysto select file to be edited. After
pressingENTER, content of the file will show up on the screen
-20-
Key Selections
1.3.2.7.1 F1New File
Operation
Step 1: A dialog box will prompt users with New File . Type in
the new file name and press ENTER.
Step 2: An empty screen shows up waiting users to type in a new
program.
1.3.2.7.2 F2Copy File

Operation: After pressing F2, a dialog box will prompt users to
type in a file name and press ENTER. The current file is then
copy to the hard disk with a different file name.
1.3.2.7.3 F3Delete File

Operation: Select a file to be delete by pressing . A
dialog box will pop up to confirm this operation.
-21-
1.3.2.7.4 F4Import
FunctionInput file from floppy.
OperationInsert a disk to the floppy drive and then press F4.
Select a file name by pressing. PressENTER
to input the file from a floppy disk
.
P.S.
1. floppy disk file format is ASCI code
2. SYNTEC CNC also can accept *.zip format ,when import
from floppy disk ,cnc would unzip automatically
3. if NC file too big ,operator can use more than ONE floppy
disk to import nc FILE , separates a big file to some floppy
disks ,use the same file nmae ,then inport THIS file DISK
BY DISK ,operator choose appEnd but not overWRITE ,IT
IS VERY EASY TO INSATLL A BIG FILE
4. IF OPERATOR INSTALL EHTERNET ,IT IS MORE
EASY TO INSTALL A BIG FILE FROM NET .
-22-
1.3.2.7.5 F5Export
Function: Output file to floppy disk
Operation: Select a file by pressingand then press
F5. After following the prompt in the dialog box, confirm this
operation by pressing ENTER.
-23-
1.3.2.7.6 F6RS232 Import

Function: use RS232 communication function to import NC files
Operation: Follow the prompts in the dialog box and type in needed
data.
-24-
1.3.2.7.7 F7 RS232 Export

Function: Use RS232 communication function to Export NC files
Operation: Follow the prompts in the dialog box and type in needed
data.
-25-
1.3.2.7.8 RS232 communication parameter setting

CNC parameter settings from : 3901 to 3949
-26-
1.3.3 F3DlgInput (ONLY for 940M)

Pressing "F3" under the main menu to begin dialog box input as shown
in the following figure. After users follow the prompts shown on the dialog
box to key in every needed parameter, the CNC milling controller can start
milling a work piece immediately.
1.3.4 F4Monitor
This selection displays machining speed, time, manual data input (MDI)
and some machine information such as coordinate, range or program at the
run time. Press F4 under the main menu to select this function.
Key Selections
1.3.4.1 F1Coor
Function: Toggle way of display among the four different coordinate
systems, graphical working paths display and the absolute coordinate.
(Absolute coordinate display at the upper right corner of the left half
screen.)
Operation: Under Monitor submenu, press F1 to toggle coordinate
display between the four coordinates as shown as the following figure:
-27-
1.3.4.2 F2Graph Adjust
Key Selections
1.3.4.2.1 F1Zoom
Function: To enlarge the workpiece graph.
Operation: Under Monitor submenu, press F2 and then F1.The
operator can use the cursor to move the frame to the determined
area.
1.3.4.2.2 F2Graph Reset

Function: To recover the zoomed workpiece graph.
Operation: Under Monitor submenu, press F2Graph Adjust and
then F2Graph Reset
1.3.4.2.3 F5Simu Setting

Function: To set simulation parameter
Operation: Under Monitor submenu, press F2Graph Adjust
and then F5Simu Setting .
-28-
1.3.4.3 F3MDI Input

FunctionManual Data Input
OperationUsers can operate SNC Milling Controller manually in MDI
mode. Press F3 under Monitor submenu and type in single-line G or M
code. Press F1 (OK) to confirm the input command. The typed-in
command line will show on right upper corner of the screen. Users
simply press CYCLE STARTon the machine panel to execute the
single-line command. The following figure shows an example of this
function.
-29-
1.3.4.4 F4SETTING
FunctionTo set the part count and also set required current
OperationFrom this screen users can set the part count what he needs
1. When CNC execute M02 ,M30 ,M99 ,part count would add 1
automatically ,
2. When part count reach required part count ,CNC would stop
executing.
-30-
1.3.4.5 F5Tool Setting

FunctionTo set the tool compensation value
Operation
Radius : G41/G42 tool radius Dn compensation (not diameter)
Radius wear : for small radius dimension adjust
Length : G43/G44 tool length Hn compensation
Length wear : for small length dimension adjust
-31-
1.3.4.6 F8Work Record

FunctionThis table can record 300 sets executed NC file ,this is very
helpful to know the end of user working history .
-32-
1.3.5 F5Alarm
Whenever the system or the program stops running due to some errors,
there will be an alarm message shown on the screen. In order to clear the
errors, users can press F5 in the main menu for Alarm submenu as shown in
the following figure.
-33-
Key Selections:
1.3.5.1 F1Actual
Operation: Under the Alarm submenu, press F1 to show current alarm
situation.
1.3.5.2 F2History
Operation: Under the Alarm submenu, press F2 to show the alarm
history of the system.
1.3.5.3 F5: Save

FunctionSave Alarm History To File.
OperationUnder the Alarm submenu, press F5 to save alarm history to
a file as shown in the following figure. A dialog box will prompt
users to type in file name to be saved. After selecting a disk drive by
using (), users pressENTERto confirm this operation.
-34-
1.3.6 F6Parameter
Under the main menu, press F8 and then F1 to enter this function as
shown in the following figure.
-35-
1.3.7 F7Diagnosis
This selection provides users with direct access to the memory area for
parameter checking, parameter settings and NC diagnosis function. It can
also be used to maintain and debug the control devices. Under the main
menu, press F6 and then F2 to access this function as shown in the
following figure.
-36-
Key Selections:
1.3.7.1 F1PLC State
Functionfor upgrade system software ,or Ladder ,system parameter
-37-
1.3.7.2 F2System Data

Function
-38-
1.3.7.3 F3Global Variable
-39-
1.3.7.4 F4Coord Variable
-40-
1.3.7.5 F8System Manager
-41-
1.3.8 F8Guidance
If users have any problem about SNC Mill controller, in addition to
user manual, users can also use this function for on-line help. Under the
main menu, press F8 for on-line help.
-42-
2. Machine operation panel
2 Machine operation panel

2.1 2nd machine operation panel
2.1.1 POWER ON
Turn on main power
2.1.2 POWER OFF

Turn off power
2.1.3 Emergency STOP

For safety reason ,press this button ,CNC would stop all
movement ,and also stop all main power . So ,people and machine safety is
guarantee .
2.1.4 Home mode and Home function

Description : When CNC power is on ,please do the home function
Operation :
1. Mode select to HOME mode
2. Press axis manual key X+,X-,Y+,Y-,Z+,Z-:
3. CNC would start the machine home function
2.1.5 Continues JOG (Rapid JOG)

Description : User can use this function to move the machine by press
JOG key
Operation :
1. Mode select to CON JOG mode
2. Press axis manual key X+,X-,Y+,Y-,Z+,Z- ,work table
would move
3. Operator can use JOG% or G01% adjust Jog federate
4. When operator press manual key and rapid Key at the
same time
5. CNC would move the work table RAPID speed
6. Operator can use G00% Rapid Jog federate
G00 % : Adjust G00 % (F0 .25% .50% .100%)

G01 % : Adjust G01/G02 /G03 feedrate override %:
-43-
2.1.6 Incremental JOG

Description : User can use this function to move the machine by
press JOG key
Operation :
1. Mode select to INC JOG mode
would move a fixed distance
3. Operator can set the incremental distance by G00 rotary
switch
4. , *1 : 1um ,*10 : 10um ,*100 : 100um
2.1.7 MPG JOG

Description : User can use this function to move the machine by
MPG(Manual Pulse Generator )
Operation :
1. Mode select to MPG mode
2. Select axis by hand box
3. Select incremental distance
would move a fixed distance *1 : 1um , *10 : 10um ,
*100:100um , *1000 : 1000um
2.1.8 AUTO mode NC file execute

Description : User use this function to execute NC file
Operation :
1. mode select to AUTO mode
2. After Home function .AUTO mode is available
3. Set workpiece coor.(G54..G59) ,CNC default G54 ,if user
dont set any G54..G59 in the NC file
4. Set to Tool Setting ,to select tool radius and tool length .
5. Press START key to start the NC program .
6. Press Feedhold key to feedhold the NC program ,if its
necessary
2.1.9 MDI mode single block execute

Description : User use this function to execute a block without NC file
Operation :
1. mode select to MDI mode
2. After Home function .MDI mode is available
3. Main function select F4Monitor
4. Press F3 MDI Input, screen would pop up a window.
5. After key in data ,press ENTER key to input the data
6. Press START key to start the MDI block.
7. If MDI block syntax is correct ,data in MDI menu would
disappear
-44-
2.1.10 MPG Simulation
Description : User can use this function to check NC file

Operation :
1. Mode select to AUTO mode
2. Press this button ,and button led light ON
3. Press START key to start the NC file.
4. CNC would change machine status from READY to
BUSY
5. Machine is still not moving
6. Operator can use rotate MPG to start the NC file
7. MPG rotate faster ,machining speed is faster
8. When MPG stop ,CNC stop.
9. This function can Enable Disable immediately
P.S. this function is very friendly for user to check his programs
2.1.11 Dry Run

Operation :
4. CNC would change machine status from READY to
BUSY
5. This function can Enable Disable immediately
2.1.12 Single block

Operation :
4. CNC would execute NC file only one block and STOP
5. CNC would change machine status from BUSY to
B_STOP
6. Press START again ,then CNC execute next block
7. This function is for user to check his NC file Block by Block
-45-
2.1.13 Option Stop
Description : User can use this function to decide NC file M01 is

STOP or not
Operation :
4. When CNC execute M01 ,CNC would STOP
5. CNC would change machine status from BUSY to
Feedhold
6. This function uses to change tool or check workpiece
2.1.14 Option Skip
Description : User can use this function to decide NC file / is skip

or not
Operation :
4. When CNC execute / ,CNC would skip this block
5. If this key is not pressed ,CNC would execute this block
2.1.15 Spindle control
Spindle CW rotate
Spindle stop
Spindle CCW rotate
Spindle low speed: When spindle is rotate, press this key,
spindle would rotate with low speed
-46-
2.1.16 Working led
ON/OFF working led
2.1.17 Working Liquid
Flush working liquid
2.1.18 Aux table backward
2.1.19 Aux table forward
-47-
2.2 Text key description:

English 26 character key
numerical key
delete a character
Insert /replace mode switch
for select keyboard the other textkey
for select keyboard the other textkey
Backspace delete a character
RESET abort the CNC status ,so please be careful to

use this key
to input current data to input box
press this key ,user can get help message about this

screen
for optional skip key input
end of block
decimal fraction
(, ), [, ], |, !, &, $, #, <, >, =, %, @, *, :, ,, +, -
Above symbols are used for Program Edit mode.
-48-
edit cursor Page Up /Page Down
edit cursor control key
-49-
3. How to operate SYNTEC 900ME
3 How to operate SYNTEC 900ME

This chapter is written for user task,when user operates this
controller ,operator can follow task description as below STEP by STEP ,so
very easy to use this controller ,TASK description as below :
1. Manuel function(JOG ,INC_JOG ,MPG)

2. HOME
3. Open a file (EDIT / FLOPPY /RS232 )
4. Tool setting (G40/G41/G42 ,G43/G44/G49)
5. Tool Length measurement (G43/G44/G49)
6. Setting the Workpiece origin offset value(G54..G59)
7. Manual Data Input(MDI )
8. Assigned an executing NC file (AUTO)
9. Graphic Simulation
10. How to check NC file in SYNTEC controller
11. Auto center
12. Auto Tool
-50-
3.1 Manual function (JOG, INC_JOG, MPG)

When power on SYNTEC CNC, there are 3 mode to manual machine
1st CON_JOG :
1. Release emergency stop button ,CNC status NOT READY
change to READY
2. Mode select switch rotate to JOG mode
3. Press axis direction key(X+,X-,Y+,Y-,Z+) ,table would
move
4. Operator can use JOG% adjust JOG speed
5. Operator can press axis direction key and rapid key at
the same time, machine will move by rapid speed
6. Rapid JOG speed can be adjusted by G00%
Incremental JOG :
change to READY
2. Mode select switch rotate to INC JOG mode
3. Press axis direction key(X+,X-,Y+,Y-,Z+) ,table will
move a fixed distance once
4. Operator can select incremental distance by G0%
(*1,*10,*100)
MPG incremental jog (MPG):

change to READY
2. Mode select switch rotate to MPG INC JOG mode
3. Select movement axis
4. Select movement distance (*1,*10,*100)
5. Rotate MPG ,table would move .
-51-
3.2 HOME
Because tool setting ,workpiece coordinate setting is based on Machine
zero point .So ,it is necessary to make sure where is machine zero (HOME).
When CNC bootup, execute HOME function is very important ,otherwise
SYNTEC CNC controller would not be allowed to start AUTO NC files
Procedure :
change to READY
2. Mode select switch rotate to HOME mode
3. Press axis direction key(X+,X-,Y+,Y-,Z+) ,axis would
start HOMING
4. Home direction is defaulted in the CNC parameter
5. Home function can run 3 axis at the same time
6. After home function, machine coordinate would be zero .
7. After home function completed, software limit protection is
available .Therefore, please dont run machine too fast,
before HOME function.
-52-
3.3 Open a file (EDIT / FLOPPY / RS232)

Procedure :
1. Press Group function key Program
2. Press submenu function key File manage
3. Screen display file system screen
4. Press F1 New file ,to open a new file

5. Press F2copy file ,to copy current hilight file to target file
6. Press F3 delete file ,to delete current hilight file
7. Press F4 Inport ,to inport a new file from floppy disk
8. Press F5 Export ,to export hilight file to floppy disk
9. Press F6 RS232 Inport ,to inport a new file from
RS232
10. Press F7 RS232 Export ,to export hilight file to RS232
-53-
3.4 Tool setting (G40/G41/G42, G43/G44/G49)

Procedure for setting Tool offset value :
1. Press Group function key Monitor
2. Press function key Tool Setting
3. Move the cursor to the compensation value to be set or
change using page keys and cursor keys
4. Type A or I key to selected input type is Absolute
or Incremental
5. Generally use Absolute type to input Tool radius and Tool
length
6. Use Incremental type to input radius wear and Length wear
for small value adjust
7. (Tool radius + radius wear ) is real G41/G42 compensation
value
8. (Tool length + length wear) is real G43/G44 compensation
value
-54-
3.5 Tool Length measurement (G43/G44/G49)

Procedure :
1. Use manual operation to move the reference tool until it
touches the specified position on the machine.
2. Press Group function key Position and clear relative
coordinate to zero
3. Press Group function key Monitor and press Tool
Setting to this screen
4. Use manual operation to move the tool until it touches the
same specified position that have been measured. The
difference of measured that is between the length of the
reference tool and the tool is displayed in the relative
coordinates on the screen.
5. Move the cursor to the compensation number for the target
tool(the cursor can be moved in the same way as for setting
tool compensation values)
-55-
3.6 Setting the Workpiece origin offset value

(G54...G59)
Procedure :
1. Press group function key Position
2. Press sub selection soft key Workpiece coor.
3. The screen for displaying the workpiece origin offset values

consists two pages . Display a desired page by Press
PageUp/PageDn key
4. Move the cursor to the workpiece origin offset to changed
the values.
5. Extenal shift input the value ,which can shift the whole
coordinate(G54..G59.8) simultaneous
6. F1coor. Latched: user can press this function key ,and
CNC would latch current machine coordinate to the screen
where sursor is located .
-56-
3.7 Manual Data Input (MDI)

Procedure :
1. Mode select switch rotate to MDI mode
2. Press group function key Monitor
3. Press sub selection soft key MDI input
.
4. The screen display the MDI input window

5. Key in MDI data at input bar and press ENTER
6. Press 2nd operation panel START to execute the current
block
7. If current block SYNTAX is correct ,the data in the window
would be disappear .
-57-
3.8 Assigned an executing NC file (AUTO)

Procedure :
1. Mode select switch rotate to AUTO mode
2. Make sure CNC status is READY
3. Press group function key Program ,select NC file what
user want to execute
4. Press group function key Monitor,then executing file is

assigned automatically .
5. Please make sure CNC status is READY, that is the only

available status to assigned executing NC file .
-58-
3.9 Graphic Simulation

Procedure :
2. Press group function key Program ,select NC file what
user want to execute ,press sub menu Simulation
3. User can use STEP to check NC file step by step

4. Use Continue to simulation whole picture
5. Use Zoom check more detail
6. Use Simulation setting set simulation parameter
7. CNC status is READY, Press group function key
Monitor
8. that is the available status to assigned executing NC file .
-59-
3.10 How to check NC file in SYNTEC controller

MPG simulation Procedure :
2. Press group function key Monitor
3. Press MPG simulation key enable this function (led on)

4. Press Start key ,CNC status from READY to BUSY
5. Machine table current status is static
6. Operator rotate MPGs ,then table is start moving along
cutting path
7. MPG rotates more fast ,table moves more fast ,MPG
stop ,table is stop from monitor screen ,operator can see the
cutting cursor move along simulation path
8. Operator also can press Single Block key ,enable single
block function when MPG simulation function is
ON ,then user can use two function simultaneous ,check
NC file STEP by STEP ,with MPG simulation function .
9. MPG simulation can control table forward ,also can
control backward too ,but NC file would stop at M,S,T code
when backward .
-60-
3.11 Auto Center

Specification:
It is usually used to look for the center of the coordinate which is the
origination of the executing procedure. So it needs to touch both sides of the
tool. The center workpiece can be calculated by system after getting their
coordinate, then the operator chooses a group of workpiece coordinate
(G54~G59.9) as the origination of the executing procedure.
Here we supply the operation introduction of manual center and auto
center as follows.
3.11.1 Manual Center

Operator moves tool to touch the edge of the workpiece by rotating
MPG, the center coordinate can be calculated by system after pressing
function key.
Operation:
1. To enter center submenu, press F1Positon=>F5workpiece
Coor=>F5Middle Func.
2.
3. To change middle function to manual center, input 0(manual
center) in center submenu, then press enter, manual center
submenu can be displayed as follows.
4. Take the tool to touch Px1 spot in the figure by handwheel,

press F1Px1,the X machine coordinate value of Px1 can be
noted in the screen and calculate X intermediate machine
coordinate with Px2, the value can be displayed in Pxm and
X-axis of Aux coordinate.
5. Take the tool to touch Px2 spot in the figure by handwheel,

press F2Px2,the X machine coordinate value of Px2 can be
-61-
noted in the screen and calculate X intermediate machine

coordinate with Px1, the value can be displayed in Pxm and
X-axis of Aux coordinate.
6. Take the tool to touch Py1 spot in the figure by handwheel,

press F3Py1,the Y machine coordinate value of Py1 can be
noted in the screen and calculate Y intermediate machine
coordinate with Py2, the value can be displayed in Pxm and
Y-axis of Aux coordinate.
7. Take the tool to touch Py2 spot in the figure by handwheel,

press F4Py2,the Y machine coordinate value of Py2 can be
noted in the screen and calculate Y intermediate machine
coordinate with Py1, the value can be displayed in Pxm and
Y-axis of Aux coordinate.
8. Press Esc to exit Auto Center and return to Workpiece

Coor submenu.
9. In Workpiece Coor submenu move cursor to the location

of the workpiece coordinate which will be set, press F3
AUX Latched. At this time the system will set the value
of the AUX coordinate into the filed in accordance with the
axis where the cursor stop.
-62-
3.11.2 Auto center operation

Auto center function is different to manual center function .The
operator only need to input the size of the workpiece and set the border
coordinates of the workpiece. Move the tool to the start point and press
startup, the system will find the center coordinate automatically.
Operation
1. To enter center submenu, press F1Positon=>F5workpiece
Coor=>F5Middle Func.
2. To change middle function to auto center, input 1(auto center)

in middle function submenu, then press enter, auto center
submenu can be displayed as follows.
3. Choose the quadrant to process and input workpiece data, the

description of the field to input an follows.
Workpiece length I: the workpiece actual length in X-axis
direction
Workpiece width J: the workpiece actual width in Y-axis
direction
Safe distance H: this is the length more than the distance
between the start point of the tool P2 and workpiece,
regardless of X-axis direction or Y-axis direction.
Feed rate: detection rate of auto center.
Z-axis safe height: this is the height that the tool will not
encounter the workpiece when it moves above the
workpiece,P1 in the figure as follows.
-63-
4. Move to Z-axis Safe Height Teach, the location of P1 as

displayed in the figure. Press F8 Z safe height teach, the
value of Z-axis machine coordinate will be noted
simultaneously as the safe height when tool moves above the
workpiece.
5. Move the tool down to P2 under the surface of work piece as

the start point of auto center.
6. Press F2Start, the tool will be moved to touch the

workpiece according to the data which has been set and the
value will be displayed on the screen. Finally the center
coordinate of the workpiece in XY-axis direction can be
calculated.
7. Press Esc to exit center function back to workpiece

coordinate submenu.
8. Move the cursor to the location of the workpiece coordinate

which will be set in workpiece coordinate submenu. Press
F3AUX Latched and the system will set the AUX
coordinate Pxm or Pym into the workpiece coordinate
system according to the axis that the cursor stops.
-64-
3.12 Z-axis Auto Tool

Specification:
Z-axis auto tool function measures the location of tool point of
different tool number through the tool calibrator on the machine, then
operator makes the distance that the location of the tool point to the datum
plane of the workpiece is fixed to amend the processing datum plane.
Operator can teach the distance into workpiece coordinate system as the gist
of the tool offset when processing.
Operation:
After starting, F1Positon=>F5workpiece Coor=>F6Auto Tool
-65-
Auto tool length measurement

It needs to measure the length of the tool again when change another
tool in order to compensate the correct tool length to the processing path.
1. Coordinate workpiece number P:0: auxiliary point,1: 1:G54,

2:G55, 3:G56, 4:G57, 5:G58, 6:G59, 7:G59.1
2. Measurement rate F: set auto tool bottom detection of the
first time and rebounding speed of every time.
3. Use reference point coordinate: set whether to re-move to the
reference point and then auto tool or not.
0 the current location ,as the start point of auto tool and
directly do bottom detection.
1The system will first complete the following steps and then
do auto tool.
I. Z-home
II. XY-axis move to the location of the second reference
point
III. Z-axis down to the start point of auto tool.
4. Reference point X in X-axis direction: this field can first

move spindle to new auto tool position coordinate and then
throughXY machine coordinate teachto correct the
location of the auto tool reference point in X-axis(if no
correction system, the previous value will be set as the preset
value);
5. Reference point Y in Y-axis direction: this field can first
move spindle to new auto tool position coordinate and then
throughXY machine coordinate teachto correct the
location of the auto tool reference point in Y-axis(if no
correction system, the previous value will be set as the preset
value);
6. Start point Z in Z-axis direction: this field can first move
spindle to the new location of auto tool start point in Z-axis
and then throughZ machine coordinate teachto set Z-axis
start point of auto tool ;
7. Z-axis lowest machine coordinate H: the height to down
Z-axis that the spindle will not hit the tool calibrator, press
function key Z machine coordinate teachto set the value;
-66-
Start
Use reference coordinate
Correction
XY reference point
correction
Correct XY coordinate
No use of
reference point No correction as new reference point
coordinate
( )
Z-axis startint point

correction
Setting completed
Z-axis lowest point

correction
Setting completed
Start auto tool
Bottom detection and

execute auto tool
-67-
Delta z set:
Delta z set is mainly used to measure the distance between the surface
of the workpiece and the tool calibrator when change another workpiece and
the system will note the value to external shift. The value can automatically
combine and calculate with the tool length measured to produce the correct
path.
1. Delta z value: display the height delta value between the

surface of the workpiece and the tool calibrator, correspond
to Z-axis set value in external shift.
2. Operation: first do tool length measurement then set delta
Step 1: take tool tip to top of workpiece
Step 2: press F3,delta z set
Auto tool measurement action

introduction
XY reference point
Z-axis starting point
5mm
3mm
Tool calibrator
Z-axis lowest point
dthe value of error
-68-
Tool calibrator action specification:

1. First move the spindle to XY-axis tool calibrator reference
point
2. Z-axis moves to start point ar 7000mm/min
3. Z-axis moves toZ-axis min coordinatethat the operator
input at measuring speed and stops immediately while
touching tool calibrator.(if dont touch the tool calibrator
after arriving at the lowest coordinate, there will be an
alarm[Z min coordinate set error alarm] immediately)
4. Back Z-axis 5mm at the speed measured
5. Z-axis moves down 6mm at 50mm/min and will stop moving
and note Z-axis machine coordinate if touch the tool
calibrator in the process.( if dont touch the tool calibrator
after moving 6mm, there will be an alarm[Auto tool length
measurement error alarm] immediately)
6. Back Z-axis 3mm at the speed measured
7. Z-axis moves down 4mm at 50mm/min and will stop moving
and note Z-axis machine coordinate if touch the tool
calibrator in the process.( if dont touch the tool calibrator
after moving 4mm, there will be an alarm[Auto tool length
measurement error alarm] immediately)
8. Judge if the error noted in 0.01mm,input the min unit integer
into Z-axis coordinate that operator chooses after averaging;
if the error exceeds 0.01mm,there will be an alarm [Auto tool
length measurement error alarm] immediately
9. G90 G53 Z0. back tool to Z-axis original point of machinery.
-69-
3.13 RS232 FUNCTION
DNC SOFTWARE CONTROLLER (SYNTEC NC

CONTROLLER SOFTWARE)
DESCRIPTION
Users can uses software of CAD/CAM transfer data to controller by
RS232 cable. Let user can select be transferred NC file to working.
Operation
1. Step IThe hardware line link to COM1
2. Step IIParameter of SYNTEC software system setting
(Suggest value of default)
Param. Controller Meaning of parameter

3901 0 Dc protocol role, 0CNC, 1Device or PC
3903 1 File transfer port number(1:Com1, 2:Com2)
3921 2 Com1 baud(0:24;1:48;2:96;3:192;4:384..)
3922 8 Com1 data bit number
3923 0 Com1 exchange code type (0:ASCII;1:EIA;2:ISO)
3924 0 Com1 control code (0:No;1:DC2;2:DC4;3:DC2DC4)
3925 1 Com1 End-of-block output code(0:EOB;1:CR+EOB)
3926 0 Com1 DC3 control code parity (0:Off;1:On)
3927 2 Com1 flow control(0:No;1:CrsRts;2:XonXoff)
3928 1 Com1 parity check(0:No;1:Odd;2:Even)
3929 1 Com1 stop bit number(1:1 bit;2:2 bit)
3. Step IIITurn on the controller power. The RS232 file input

is ready.
-70-
Operation has been stated as follows.

I. Press [program] [file manage] to file manage submenu.
And than to press [=>] show up as follow:
II. press [RS232 Import].show up as follow
III. After input the file name, Press [Ok] . Then the program
will wait for receive state. The transfer state will has
shown on transfer process.
4. Step IVExecuting DNC software. Does the RS232 transfer

setting adjust is the same controller, or controller adjust is the
same of DNC software. Executing the send function of DNC
software. It can be transferred into which the file of output.
Attention
When operating. The file input should be doing firstly. Let controller
stay on the receive file state. And then to set up transfer file function of
DNC software. It can be sure transfer correctly.
-71-
3.14 DNC Function
DNC SOFTWARE CONTROLLER (SYNTEC NC

CONTROLER SOFTWARE)
DESCRIPTION
When user is use the CAD/CAM software. The controller doesnt
capacity in saving the too large size program in working. Use this function
to execute that aside transfer and aside working.
Operation
2. Step IIParameter of SYNTEC software system setting
(Suggest value of default)

3921 2 Com1 baud(0:24;1:48;2:96;3:192;4:384..)
3. Step IIIExecuting DNC software. Does the RS232 transfer

setting adjust is the same of controller, or controller adjust is
the same of the DNC software. Executing the send function
of DNC software. It can be transferred into the file of output.
4. Step IVTurn on controller power. Into system by press

[program] [file manage] to file manage submenu. Select the
RS232 DNC Program is a working file. It is shown as
follows.
-72-
5. Step press monitor. Controller will read into file to

working by RS232
Attention
When operating. It should be doing that the working file from DNC
software output wait controller to reading firstly. And select RS232 DNC
Program is working file on controller. Finish, Setup working. It can be sure
transfer correctly.
-73-
3.15 The software of SYNTEC controller replace

the software of DNC to execute RS232
function
PC(SYNTEC software end of PC) controller
DESCRIPTION
The SYNTEC controller software made user transfer into controller
working by RS232 that CAD/CAM generate or writing file. But the
SYNTEC controller software cant offer the DNC software that aside
transfer and aside working function.
Operation
2. Step II Parameter of SYNTEC software system setting
(suggest setting value. Exception of 3910 other all the same)

3921 2 Com1 baud(0:24;1:48;2:96;3:192;4:384..)
3. Step IIITurn on the controller power. The RS232 file input

is ready. Operation has been stated as follows.
-74-

I. Press [program] [file manage] to file manage submenu,
And than to press [=>]show up as follow
II. press [RS232 Import].Show up as follow
III. After input the file name. Press [Ok].Then the program
will enter into waiting for receive state. The transfer
state will be shown on transfer process.
-75-
4. Step IVUpper End of PC. Executing c:\cnc\cnc into the

controller simulation software. Does RS232 file output.
I. Press [program] [file manage] to file manage submenu.

Than to press [=>] key to appearing. And press up/down
key select that want output of file. Such as O1000.
II. press[RS232 Import].show up as follow
III. After press [Ok] .Start transfer program. And appearing

state of transfer.
-76-
Attention
1. When operating. The file input should be doing firstly. Let
controller stay on the receive file state ,and to setup transfer
file function of DNC software. It can be sure transfer
correctly.
2. 2Be careful. SYNTEC controller software can offer RS232
file transfer function. But cant offer DNC software that
aside transfer and aside working function.
3. 3The most our must be careful. When PC executing. We
suggest that add up /M /P parameter behind batch of cnc. Let
controller software can execute simulation controller of
function on PC. The /M is operate plate of simulation. User
can setup working from keyboard. The /P will simulate ISR
and cover off Interrupt. Convenient software can execute
upper the Windows. But will be invalid of transfer
function if behind batch of cnc add up /P parameter.
-77-

Mill Operation Manual en 1

Uploaded by

Copyright:

Available Formats

Mill Operation Manual en 1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mill Operation Manual en 1

Uploaded by

Copyright:

Available Formats

SYNTEC

Mill Controller Manual

1.1 CNC System Configuration............................................................................ 1

1.2 Screen Sections .............................................................................................. 2

1.3 Main Menu Selections ................................................................................... 3

2 MACHINE OPERATION PANEL ...................................................................43

2.1 2nd machine operation panel ..........................................................................43

2.2 Text key description:.....................................................................................48

3 HOW TO OPERATE SYNTEC 900ME ...........................................................50

3.1 Manual function (JOG, INC_JOG, MPG) .....................................................51

3.2 HOME ..........................................................................................................52

3.3 Open a file (EDIT / FLOPPY / RS232) .........................................................53

3.4 Tool setting (G40/G41/G42, G43/G44/G49) .................................................54

3.5 Tool Length measurement (G43/G44/G49) ...................................................55

3.6 Setting the Workpiece origin offset value (G54...G59) ..................................56

3.8 Assigned an executing NC file (AUTO) ........................................................58

3.9 Graphic Simulation .......................................................................................59

3.10 How to check NC file in SYNTEC controller ................................................60

3.11 Auto Center ..................................................................................................61

3.12 Z-axis Auto Tool...........................................................................................65

3.13 RS232 FUNCTION ......................................................................................70

3.14 DNC Function ..............................................................................................72

1 CNC Milling Controller Interface

Position Program Dlginput Monitor Alarm Param. Diagnosis Guidance

Coor Insert Cycle Coor Actual System Param PLC State

1/2 Coor Delete Line Graph Adjust History Go to page One

Go To Line PLC Register

Copy Line PLC Timer

Insert Line PLC Counter

Teach System Data

Arc Teach Software Setup

Cancel Middle Backup System

Delete Line Install Local L.

Simu. Store Language

1.2 Screen Sections

Meanings For Fields on the Display:

1.3 Main Menu Selections

Meaning of fields on the display------

Function key selections

1.3.1.2 F21/2 Coor.

1.3.1.3 F3Clear Coor.

1.3.1.4 F4Clear All Relative

1.3.1.5 F5Workpiece Coor.

1.3.1.5.1 F1Coor. Latched

1.3.1.5.2 F2Rel. Latched

1.3.1.5.3 F3Aux. Latched

1.3.1.5.4 F5Middle Point Func.

1.3.1.5.5 F6Tool Tip Measure

Program Sub menu Key Selections:

1.3.2.2 F2Delete Line

1.3.2.3 F3Edit Cycle

1.3.2.4.1 EDIT sub function F1 : Search

1.3.2.4.2 EDIT sub function F2 : Replace

1.3.2.4.3 EDIT sub function F3 : Go To Line

1.3.2.4.4 EDIT sub function F4: copy line

1.3.2.4.5 EDIT sub function F5: Insert line

Teach sub Key Selections

1.3.2.5.2 F2Line Teach

1.3.2.5.3 F3Arc Teach

1.3.2.5.4 F4Cancel Middle