BHARAT HEAVY ELECTRICALS LTD., Enquiry No.

:
CORPORATE R&D DIVISION Date : 28/05/2010
VIKAS NAGAR, HYDERABAD-500093 (INDIA)
PURCHASE SECTION TECHNICAL SECTION
PHONE 0091 40 2377 8474 PHONE: 0091 40 2388 2334
FAX 0091 40 2377 6320 Fax 0091 40 23776320
P.B.Reddy Contact: Dr. A. Bhoomaiah
[email protected] E-mail: bhooma @bhelrnd.co.in SPEC.NO.
PS: HVE:10: EF:01/00

SPECIFICATION CUM COMPLIANCE CERTIFICATION FOR EPOXY FLOORING IN UHV LAB

Important
1. Vendor must submit complete information against clauses Nos 11.0 and 12.0. The offer meeting these clauses would only be processed.
2. The offer and all documents enclosed with offer should be in English language only.
3. BHEL reserves the right to verify the information submitted by the vendor. The offer with false/ incorrect/incomplete information may be rejected.
4. Vendor shall sign and stamp all sheets.
5. Offers submitted shall be valid for a period of minimum 6 (six) months from date of commercial bid.
6. Revised technical bid may be necessary should the specification require up gradation/ modification on technical scrutiny of offers.
7. Vendor must respond to all points in the specification.
ADDRESS OF THE SUPPLIER : ADDRESS OF THE INDIAN AGENT :
TELEPHONE NOS.: TELEPHONE NOS.:
FAX NOS.: FAX NOS.:
CONTACT PERSON: CONTACT PERSON:
E-MAIL ADDRESS : E-MAIL ADDRESS :
SCOPE: Supply and installation of Epoxy Eurethane floor system in Ultra High Voltage laboratory at BHEL complying with following specifications.

Quantity: System consisting of prime coat, screed coat, and topping coat and total built up thickness of the floor should be 5mm

Serial No. DESCRIPTION OF REQUIREMENT DESIRED ACTION OFFERED BY THE VENDOR DEVIATIONS REMARKS(Only on deviations)
(IF ANY, ELSE PRINT NONE)

Purpose of epoxy flooring system: Providing and laying 4mm

thick high density epoxy based heavy duty industrial screen flooring and
topped with 1mm thick of self leveling compound to achieve total thickness
1.0 Vendor to note
of 5mm.This system will make a smooth surface and will be used to take
load movements on air casters.The floor also offers resistance to abserb
water, oil , and industrial chemicals etc. Very easy to clean the surface.

End use of the Area: Test equipment like Impulse Volatage Generator,
AC test transformer,Swichgear panael, potential divider and test objects etc.
1.1 Vendor to note
will be installed at different locations. Total load of 25 tons will be
distributed in the 40 X 24 meters area.

Description of the Area: The size of the test bay is 24 metres X 24

metres, the size of the assembly area is 19.7 metersX 8.9 meters and the
1.2 Vendor to note
size of the utility area is 19.7 meters X 8.9 meters. Total floor area is
arround 930 square meters

Temperature inside the test hall : Maximum expected ambient Vendor to note as input
1.3
temperature is 45 C. parameter

Page 1 of 4
Serial No. DESCRIPTION OF REQUIREMENT DESIRED ACTION OFFERED BY THE VENDOR DEVIATIONS REMARKS(Only on deviations)
(IF ANY, ELSE PRINT NONE)

2.0 Material specifications:

Performance properties: Flexible modified epoxy for crack

bridging,impact absorption and application over substracts with high
2.1 difflection or vibration. Epoxy flooring composition system shall be a resin Vendor to conform
rich composite with low viscosity,clear epoxy primer for maximum bond
potential.100% solids, top coat for final seal.

Matrix coating system: Consists of prime coat, screed coat and topping
2.2 Vendor to conform
coat

Primary coating: The primary coat is a two component full solids coating
with excellent bonding on to concrete surface. The application is by
lambskin short pile roller / screeder at a spreading rate of 0.25 to 0.75 kgs
2.3 Vendor to conform
per sqare meter. Total builtup thickness should be 200 micron. Primary
coat is allowed to get track free before application of heavy duty industrial
screed.

Screed coating: Base lining is done with a three component solvent free
epoxy urethane urea screed to fill the post holes / dents on the base floor
and level the undulation / pot holes of the base floor. The spreading rate for
this is to be determined by the extend of leveling required for the base
2.4 floor and thickness that is proposed to buil up. The buil up thickness of this Vendor to conform
screed floor shall be arround 3000microns. The screed is kept for curing
upto 4 to5 hours to get workable strength for next proceedure. An
intermediate coat (Base coat) is to be applied to avoid any pinholes,
waviness etc.

Top finish coat: Two component epoxy urethane urea coating which is
applied by lambs wool roller / roller notched trowel . Total built up
2.5 thichness shall be arround 2000microns. Dust & dirt has to be removed Vendor to conform
from the surface before starting the top coat.The colour pigment will be
finalised at the time of purchase order .

Page 2 of 4
Serial No. DESCRIPTION OF REQUIREMENT DESIRED ACTION OFFERED BY THE VENDOR DEVIATIONS REMARKS(Only on deviations)
(IF ANY, ELSE PRINT NONE)

3 Surface preparation:

Acid itching: Acidic water is to be used to clean the floor. By means of

3.1 scrubber ( machine or mannual) & washing with sufficient water, all oil, Vendor to conform
grease & foreign particles are to be cleaned properly from the surface.

Cleaning of the soaked oil : to get good bonding of the epoxy floor &
durability it is essntial to check the presence of oil (if any) inside the floor.
3.2 Vendor to conform
Burning procedure is to be carried out(if required) to remove the oil till the
floor become bright white.

Filling of the pot holes / cracks: The pot holes and expansion joints (if
any) are to be filled with the suitable material. The pat holes are to be filled
3.3 & leveled with pot filling compound. Similarly the cracks & expansion Vendor to conform
joints have to be filled with crack seal compound which is having the
expansion & compression properties as per the surrounding temperature

Self leveling compound: After final coating ,it should be kept for 24
3.4 hours for functional cure. Self leveling compound can be applied if Vendor to conform
required. to make the surface smooth and level.

Material properties: The properties of the material like solids by volume,

water absorption, hardness shore,Tensile strength, compreessive strength, Vendor to specify the
4.0
linear shrinkage ,surface hardness and desity etc shold be as perrelavant standards
standards.

Documentation: A sets of following documents (Hard Copies ) in English

5.0
should be supplied along with the materials.

5.1 Test and Guarantee certificates Vendor to conform

5.2 Brouchers / catologues/ literature etc. Vendor to conform

6.0 Fecilities provided by BHEL

BHEL will provide required water ,electricity and storage place for
6.1 Vendor to note
materials, tools brought by supplier and civil work (if any)

Execution of work:The execution of work should be carried out under

7.0 Vendor to conform
supervision of an expert engineers and technitians deputed by vendor

Commencement of work: the The system shall executed by the vendor at

the indenter's premises after clearance from the indenter. Required items
8.0 Vendor to conform
for the execution within stipulated time shall be brought by vendor on the
returnable basis.

Charges for execution: Execution charges can be mentioned separately,

9.0 Vendor to conform
however included within the scope of supply.

Performance guarantee : 12 months from the date of completion of the

10.0 Vendor to conform
work

General: Sketch / photographs of the works carried out earlier shall be

11.0 substantiated with technical offer including guaranteed parameters and meet Vendor must supply
all the classes mentioned in this NIT

Page 3 of 4
Serial No. DESCRIPTION OF REQUIREMENT DESIRED ACTION OFFERED BY THE VENDOR DEVIATIONS REMARKS(Only on deviations)
(IF ANY, ELSE PRINT NONE)

Qualification Requirements: Vender should have dealt with similar work

for at least three years. The supplier should give a reference list . Further,
12.0 Vendor to conform
the vendor must have service personnel to support the repair works in
future, as and when required, by BHEL.

Page 4 of 4