Scribd
Upload
76 views5 pages

Switch Router Specification

This document provides requirements for a logical network diagram including: 1. Two switch-routers with different port configurations and throughput capabilities. 2. Software features that must be supported on both switch-routers including L3 routing protocols, L2 features, MPLS, QoS, clock synchronization, circuit emulation and monitoring. 3. Management features including SNMP and RMON that must be supported.

Uploaded by

ziblur
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
76 views5 pages

Switch Router Specification

This document provides requirements for a logical network diagram including: 1. Two switch-routers with different port configurations and throughput capabilities. 2. Software features that must be supported on both switch-routers including L3 routing protocols, L2 features, MPLS, QoS, clock synchronization, circuit emulation and monitoring. 3. Management features including SNMP and RMON that must be supported.

Uploaded by

ziblur
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Required Logical Network Diagram:

Hardware Features:

Type Physical configuration Other Features (Defined from


chipset)
Switch-Router 5+ GE (SFP and RJ-45 combo) Throughput:
#1 Ports, Either SFP will work or Forwarding Capacity:
the RJ45 Copper port will work DRAM/Flash:
at a time but not both ports at the Min Routing table size:
same time. Dual DC -48V Power
Supply.
Add a slot to add 8E1
and create an E1 Card.

Switch-Router 10x1GE (SFP) + 2x1GE (RJ-45 Throughput:


#2 + SFP Combo) + 4 x 10GE Forwarding Capacity:
(SFP). Dual DC -48V Power DRAM/Flash:
processing board 1+1 Min Routing table size:
redundancy.

Both Switch-Router must have following Software Features:

Type Main Features Sub Features/Explanation


L3 Features
Static Routing
OSPF (v2/3) Graceful restart,
Bidirectional Forwarding Detection(BFD)
support for faster failover,
8- path for equal cost multi path(ECMP),
ipv4 and ipv6 support
IS-IS Graceful restart,
Bidirectional Forwarding Detection(BFD)
support for faster failover,
8- path for equal cost multi path(ECMP),
ipv4 and ipv6 support
BGP Graceful restart and BFD,
8- path for equal cost multi path(ECMP),
ipv4 and ipv6 support
MP-BGP(multiprotocol extension of BGP,
Route-reflector, confederation and
synchronization
Routing policy with BGP Path Attribute
Common L3 features VRRP,
Hardware based layer-2 and 3
ACL(inbound and outbound), TCAM
( tertiary content addressable memory)
Prefix-list,
Route-map,
Distribute-list,
Route-redistribution,
Route-filtering,
Route-summarization and aggregation
Policy based routing,
Load balancing,
Separate routing and forwarding table.
L2 Features
ERPS G.8032 v1/2
STP/RSTP/MSTP Per VLAN Spanning Tree support,
Root Guard,
BPDU Guard
Port Security
Port fast
VLAN,QinQ Min 4,096 VLAN
Min 12,000 MAC address table size
Aging Time [1 to 10,000+]
LACP IEEE802.3ad
MPLS
Features
Label Distribution Seamless/Unified MPLS support
Protocol(LDP)
L2 VPN VPWS,
VPLS,
Hierarchical VPLS
(IETF RFC4664 L2VPN framework)
L3 VPN Virtual routing and forwarding VRF
( minimum 128),
Route-target,
route-distinguisher,
address-family: ipv4,ipv6,l2vpn, vpnv4
and vpnv6.
PE-CE routing OSPF,
(ipv4 & ipv6) BGP,
Static.
Traffic Engineering RSVP(BFD for LSP),
OSPF-TE,
ISIS-TE,
CSPF,
FRR for < 50 ms of failover time
QoS Flow/Traffic Broadcast, multicast and rate-limiting,
Classification, Protection switching criteria:
Traffic shaping and LoS (Loss of Signal) or degradation of any of the
policing, QoS KPIs (QoS parameters as: e2e Packet Delay <
Congestion 10 ms, e2e Jitter < 4 ms, Packet Loss < 10-6 ) on
management, any fiber cut or hardware failure or link
WRED, degradation.Switching time < 50ms.
Min 8 queues per
port (strict
priority(SP) and
weighted round
robin(WRR)
queuing),
Protection
switching.
Clock Sync. IEEE 1588v2
Circuit
Emulation (for SAToP,
E1/SDH
support) CESoP

Interface

9600 byte
Jumbo Frame DDM features (Tx/Rx power,Temperature)
(MTU size) Interface Bit Errors, CRC errors, Pause
frames, delay, reliability, load + other
SFP/XFP common statistics.

Monitoring NBIF support for alarm and performance


ITU-T Y.1731, monitoring.

IEEE 802.1ag,

IETF RFC2544.

Alarm and
performance
monitoring.

Management
SNMP v1/2/3
RMON

You might also like