GSM Training Manual PDF

GSM Training Notes Racal Instruments Group
Introduction to cellular radio
Milestones in radio
Traditional mobile radio
Cellular network planning
Cells do overlap !
Cellular radio - why does it work?
Cellular design objectives
Introduction to cellular radio - Page 1

Milestones in radio
1901 1st transatlantic radio transmission

1904 John Ambrose Fleming invented the diode
1919 Dr Frank Conrad (Westinghouse in USA)
1919 H.J. Round (Marconi Wireless Telegraph
UK)
1921 Detroit police department
1948 Transistor announced by Bell Telephone
1981 NMT (Nordic Mobile Telephone) system
1991 First commercial GSM system
The Radio Story So Far
Radio communication started at the beginning of the 20th Century,

with a handful of famous scientists making individual calls, sometimes
across large distances.
Land mobile communications as we know it started in 1921, with a
despatch system used by the Detroit Police Department and was still
available to relatively few until the 1940s.
World War II stimulated the introduction of mobile communications
but until the development of the transistor in the 1950s; and small
reliable transceivers; relatively few people had experienced the
freedom radio communication provides.
The Bell Telephone Laboratories were responsible for the
development of land mobile systems and eventually the public
cellular system in North America, however Scandinavia introduced
the first public cellular system in 1981 with the NMT system.
Now as we start the 21st Century, millions of people will be making
simultaneous conversations over personal wireless telephones. This
has only been made possible by using cellular radio techniques.

Traditional mobile radio
Coverage area Guard band
Before Cellular Radio
Before cellular radio, personal communication over large areas relied

on powerful transmitters flooding the coverage area with
transmissions. The main disadvantage of this was that very high
power transmitters were required, and the number of simultaneous
conversations was limited to the number of channels available.
This type of system limits the capacity (i.e.. number of simultaneous
conversations) as the same channels cannot be used again in an
adjacent area. A guard band is required of at least 4:1 (guard band
to coverage area) before the same channel frequency can be re-
used.
With radio spectrum a valuable resource, lateral thinking was needed
and a method that restricted the power and hence coverage areas
was required if mobile communication was to compete with land-lines
in quantity.
(Note that in some countries 120 watt mobile radios are still used for
point to point communications by the emergency services).

Cellular network planning
Cellular Concept
The cellular radio concept relies on many transmitters (or base

stations) each covering a limited area or cell. Each cell is allocated a
set of channels. These channels cannot be re-used by adjacent cells
otherwise radios would interfere, but careful frequency planning
allows the pool of channels to be re-used after a guard band.
The smaller the cells, the more often frequencies can be re-used, and
hence the greater the number of conversations in a given graphical
area. In fact the network is designed so that cell sizes are relative to
the expected number of subscribers in the area; so in an urban area
cells are small and in a rural area large.
Sophisticated planning of so called microcells and picocells are now
employed where cell diameters may be as small as 1km.
Note that a maximum cell radius of about 35 km is possible for GSM:

where hand portable coverage is required, cells are considerably
smaller.

Cells do overlap !
Cells do Overlap
Almost all the theoretical explanations of cellular radio show cells as

being honeycomb shaped. This is useful for planning purposes. but
in reality local topography distorts the uniform shape.
For seamless cellular coverage, overlaps need to occur and network
planners ensure that cells produce patterns that allow large enough
overlaps for hysterisis if a mobile moves from one cell to another.
The use of omni directional and tri-sectored cell patterns is important
for efficient use of infrastructure.

Cellular radio-why does it work ?
Seamless coverage without high power transmitters

Frequency re-use
Virtually unlimited capacity
Smart mobile terminals - controlled by the network
Frequency agile
Power control
Cellular Radio - Why Does it Work?
Emitted RF power limits the range of a standard mobile radio. In an

area with few high buildings coverage up to around 50 km radius is
possible with a vehicle mounted radio. Hand portable radios with this
range are cumbersome and would require large batteries.
Cellular radios are able to operate by communicating with the nearest
transmitter, or base station, and transferring seamlessly from one to
another.
A relatively limited amount of the frequency spectrum is available for
personal wireless communications. Cellular systems re-use this
spectrum efficiently by planning for predicted subscriber capacity.
Cellular radios are carefully controlled to produce just enough power
at an allocated frequency to ensure quality communication. This
ability to change power and frequency without the user being aware
makes the cellular system far more sophisticated than traditional
mobile radios.

Cellular design objectives
Good speech quality

Easy to use
Low operational costs
Roaming between territories
Acceptable size and battery life
New services and facilities
Cellular Design Objectives
Cellular radio was always intended to provide a radio system for the
mass market. It was designed to provide good quality portable
communications at an affordable price.
Speech quality had to be similar to the wired network and no special
technical knowledge was required to make calls.
Although initially the infrastructure costs are high, cellular has the
potential of offering affordable costs to a variety of users.
Roaming between different areas and virtually nation-wide coverage
was very desirable.
If phones were to be accepted by the mass market the size and
battery life must be acceptable.
New services, equivalent to those on the wired network must be
possible.

page intentionally left blank

Introduction to GSM
Why GSM ?
History of GSM
GSM standards
GSM & its derivatives
Services of GSM
GSM - not just voice
SIM cards
Introduction to GSM - Page 1

Why GSM ?
TACS
C-NETZ
AMPS
NMT-900
E-TACS
NMT-450
E-AMPS
RC 2000
N-AMPS
Why GSM ?
Analog cellular systems were introduced in the early 1980s and come
in many different technical standards. There are many different
standards throughout the world, some variants based on existing
networks.
GSM was initially introduced to provide a single digital standard
across Europe. This system has also been adopted in other parts of
the world and is now regarded by many as the global cellular
standard.
The GSM standard brings many benefits to end users and network
operators. For example roaming is now possible throughout many
parts of the world: this means that people can travel from one country
to another and still make and receive calls. There is no need for any
special equipment or arrangements; using the same GSM phone.
The demand for mobiles is now huge and this is driving prices down.
Test equipment also benefits form a common standard and can be
the same from one country to the next.

History of GSM
1982 Groupe Speciale Mobile formed

1987 MoU formed
1990 Technical committees produced over 100 CTRs
1991 Phase 1 recommendations
1995 Global System for Mobile Communication
1995 Phase 2 recommendations
History of GSM
In the mid 1980s a group called Groupe Speciale Mobile was formed
to produce a next generation standard that would replace the
numerous European analog cellular systems in use. It was seen as
more than just a cellular system; it was designed to be compatible
with the future telecommunications systems, particularly ISDN
(Integrated Services Digital Network).
In 1987 a group of countries stated they would participate in the GSM
system and would cooperate in 1991 by signing a MoU
(Memorandum of Understanding). This initial group of signatories
was only 18. It has evolved tenfold to become well over 180 by 1996
and is still growing.
By the early 1990s well over 100 sets of recommendations (over
5000 pages) had been produced by working with ETSI (European
Telecommunication Standards Institute) to define all aspects of the
GSM system.
In 1991 a formal type approval specification had been agreed for all
mobile stations to conform to and later that year the first public
system went into operation.
Since then further recommendations have been agreed to provide a
second phase of mobiles. GSM standards continue to develop and
new features are being added on a continuous basis.

GSM standards
P-GSM
E-GSM (Phase 2 frequency range)
MS - BTS (uplink) BTS - MS (downlink)
E P E P
(50ch) (124ch) (50ch) (124ch) Frequency
880.2 MHz 890.2 MHz 914.8 MHz 925.2 MHz 935.2 MHz 959.8 MHz
GSM standards
To ensure that GSM succeeded, 124 channels in the 890 - 960 MHz
band were defined to be exclusively for GSM. The MoU members
worked to a common goal and allocated these frequencies in their
countries.
As more members joined from countries outside Europe, it was
realised that the original GSM frequencies would not be sufficient. An
additional band was added, providing a further 50 channels. This
band is referred to a E-GSM (Extended GSM) and falls below the
original channels.
In many countries these channels are already allocated to analog
cellular service and will gradually be converted to GSM.

GSM & its derivatives
DCS - 1800
MS - BTS (uplink) BTS - MS (downlink)
1710.2 1784.8MHz 1805.2 1879.8MHz
PCS - 1900
1850 1910MHz 1930 1990MHz
What Next?
GSM & Its Derivatives
GSM had been so successful in some developed countries that more

channels were allocated in the 1800 MHz band. A delta specification,
based on GSM signalling and protocols was developed and is now
being implemented in Europe and many other parts of the world
where the frequencies are available and demand requires the
additional capacity.
In North America a number of bands allocated in the 1900 MHz
region have been auctioned to potential network operators and some
have deployed another variant of GSM using similar signalling and
protocols to GSM.
Further systems based on GSM are now planned for private
systems.
A number of global and regional satellite systems that have been
proposed also use a significant proportion of the GSM standards.

Services of GSM
Emergency Calls
Call Forwarding
Call Barring
Call Waiting
Advice of Charge
Services of GSM
Normal telephone service is enhanced by the provision of emergency
calls using standard procedure in any country i.e.. 911 or 999 or 112.
Emergency calls are possible even when a subscriber has been
barred from making regular calls and even when no SIM is fitted.
Supplementary Services
GSM supports an extremely comprehensive list of supplementary services.
The list includes:-
Call Forwarding Unconditional
Mobile Subscriber Busy
No Reply
Mobile Not Reachable
Call Barring Outgoing
Outgoing International
Outgoing International except to Home Country
Incoming
Incoming when roaming abroad
Call Waiting
Call Hold
Three Party Service
Advice of Charge
The full list of supplementary services is extensive and includes some which are
very novel. Some of these services may not be available initially, and introduction
may vary from network to network.
Data Transmission
Facsimile Group III
Short message service (SMS)
Cell Broadcast
As well as traditional speech communication a number of other

services are provided in the GSM specification. Data transmission of
9600 b/s is possible and plans to reach higher data rates are under
development. Because data uses the original capabilities of GSM,
error correction can be made even under fading conditions.
The short message service allows the transmission of 160 alpha
numeric characters to and from a subscriber. This service provides
an advanced paging service as messages may be received during
conversations. If the one is switched off or out of the area covered by
GSM, the message is stored in the network and offered to the
subscriber when they reappear on the network.
Applications such as traffic announcements can be broadcast to all
phones in a cell or geographical area using the cell broadcast feature.
These features will become some of the key competitive
differentiators between networks.

SIM cards
IMSI, PIN & PUK

Authentication & Encryption Information
Other Information
Network information
Phone Number Memory
Short Message Store
Roaming Information
SIM Cards
GSM is the first major cellular system to make use of smart card
technology. A SIM (subscriber identity module) is a tiny
microprocessor and memory embedded in plastic. It looks like a
credit card (there is also a small plug in version). The card holds
much of the users information.
The SIM is key to many GSM features especially with regard to
security. Information from the SIM is required for voice ciphering.
The SIM also stores abbreviated dialing codes and short messages.
(Note:-Test SIMs are used to provide special functions during phone

testing).

How GSM works: a mobiles perspective
A typical GSM network

Channel structure
Registration / location update
Registration information
The structure of an IMEI
The structure of an IMSI
Mobile idle
Call setup
Power control
Timing advance
Handover
IMSI detached
How GSM works: a mobiles perspective - Page 1

A typical GSM network
Databases
of
users
BTS
BTS BTS MSC

MSC
BTS
BTS BTS
BTS PSTN
BSC
BSC
MS
SIM
A Typical GSM Network
To understand how GSM works, consider what a normal GSM

system consists of.
The phone, referred to as the MS (Mobile Station) needs a SIM
(Subscriber Identity Module) to make regular communication with the
network.
The phone communicates to the network of BTSs (Base Transceiver
Stations) deployed over the coverage area.
Each BTS is connected to a BSC (Base Station Controller) which is in
turn connected to a MSC (Mobile Switching Centre).
The MSC provides connection to the PSTN=Public Switched
Telephone Network). The MSC holds important information that is
needed to ensure communication can take place.
Information held at the MSC provides details of whether phones are
likely to be switched on, details of which visiting phones may be
operating on the network. Also whether the subscriber is valid (that
the bills have been paid!)

Channel structure
Control
Control
Traffic
Traffic
Traffic
Traffic
Traffic
Traffic
Traffic
Traffic
7 0 1 2 3 4 5 6 7 0
Time
Channel structure
Each cell uses one or more of the pool of channels allocated to the
network. So as an example a GSM 900 network allocated half of the
total 124 channels would have 62 channels.
The 62 channels need to be divided up to ensure adjacent cells do
not use the same channel. In some urban cells there may be 15 or
16 channels to a BTS. Rural cells may only require one channel.
Each channel is divided into 8 time slots. One or more is used for
control and the remainder for traffic.

I am here
When a radio is switched on it needs to let the network know where it

is to enable calls to be received. As the subscriber moves around,
there is a need for the phone to update its location. This
registration/location updating is performed automatically and
according to certain rules set by the network. (There is no need to
constantly update phone locations as the network would soon
become overloaded and no useful information would be gained).
GSM radios can also de-register on power down to allow the network
to know that calls are not possible.
(Note: different networks use different strategies for locating mobiles.

Some may require the phone to update every time it moves into a
new cell : this almost guarantees location immediately. Other
networks may allow phones to move several cells before requiring an
update : finding a phone may then take longer, because a number of
cells will need to be paged before locating the mobile).

Registration information
IMSI - International Mobile Subscriber Identity

IMEI - International Mobile Equipment Identity
- Mobile Class
SIM - Subscriber Identity Module.
- PIN Personal Identity Number
- PUK Personal Unblocking Key
Registration Information
The IMSI (International Mobile Subscriber Identity) is information held

on the SIM (Subscriber Identity Module) and can be thought of as the
subscribers unique number, which is translated to provide a
telephone number by the network.
The IMEI (International Mobile Equipment Identity) is information held
on the phone and can be thought of as the electronic serial number.
This number holds information about the phone, such as class and
type.
The SIM holds information for the subscriber including a PIN number,
which is used for additional security. With the PIN function enabled,
a 4 to 8 digit number must be entered before calls can be made. If
this is incorrectly entered 3 times in a row , the SIM automatically
blocks. To unblock the SIM an 8 digit PUK (personal unblocking key)
must be entered.
(Note an Emergency call can be placed in the absence of a SIM:only
the IMEI is sent).

The structure of an IMEI
TYPE
APPROVED
TAC FAC SERIAL NUMBER SPARE
(6 digits) (2 digits) (6 digits) (1 digit)
The Structure of an IMEI
The IMEI, ranges of which are allocated upon the granting of type
approval, include the mobile TAC (Type Approval Code) and the FAC
Final Assembly plant code, and includes a serial number which is
unique for each unit of a given type.

The structure of an IMSI
MCC MCN MSIN

(3 digits) (2 digits) (10 digits or less )
The Structure of an IMSI
An IMSI (International Mobile Subscriber Identity) consists of three

parts: the MCC ( Mobile Country Code), identifying a country; the
MNC (Mobile Network Code), identifying a PLMN (Personal Land
Mobile Network) within this country; and the MSIN (Mobile
Subscriber Identification Number) identifying a subscriber within this
PLMN, using no more than 10 digits.

Main Menu 15 JAN 1996 11:24:57 Radio
Parameters
System
6103
Unsync
Offsets
Mode
Mobile and System Information
IMSI 2349178
2349178 MCC 234
Results Multimode
IMEI 23456789
23456789 MNC 91
TMSI BCCH ARFCN 121
121
Memory
Mobile Class 3 BCCH level -30.5
-85.0 dBm Single
Card
Tests
Place
Placeaacall
calltotostart
startFunctional
FunctionalTests
Tests
Test
Self Tests /
Sequences
System
Status : RR Connection Released RXQUAL : RXLEV :
GPIB : 20 Std : INT13 Results: OFF Offsets : OFF
The Racal Instruments 6103 produces the screen above, after M.S.
registrations. As well as the IMSI and IMEI, the mobile class is
displayed.
The 6103 can be configured to simulate any country or network and
the BCCH (Broadcast Control Channel) can be selected by the
operator if desired.

Mobile idle
Paging channel
Mobile Idle
Once the radio has registered, it monitors the strongest cell control
channel. Via this channel it can be paged and therefore receive calls
from the system. Usually the mobile in this state will be designed to
consume the minimum of power, non essential circuits are turned off.
If the mobile moves into a new cell area it may need to re-register in
that area.
In order to test a mobile, it is often useful to force the mobile to
perform a location update at the start of every test. This can be done
in a number of different ways, one method being to ask the phone to
register on switch on.

Call setup
Call request
Go to channel x / slot y
O.K.. Im ready
Go ahead & talk
Call setup
Calls can be set up by the user dialling out or the radio being paged
by the network. ie mobile originated or base station originated.
Calls are setup on control channel timeslots and then transferred to a
traffic channel / timeslot. (The process actually requires several
messages as authentication and the various layers of communication
are established).
Note: In a rural cell, there may be only one channel used for
combined control and traffic. One timeslot is used to send control
information and the remainder are available for traffic.
In busier cells a number of channels may be used for control
information. The traffic will be shared appropriately.

Test Running : Call Setup 15 JAN 1996 11:24:57 Stop /
Results Edit
Test Status Test in progress
Paging Mobile
Ringing Mobile
Operator - Please lift the handset
TCH ARFCN 62 TCH Slot 4

TCH Level -85.0 dBm Mobile Power Level 7
Status : Alerting Calling Party RXQUAL : 0 RXLEV : 25

Abort
GPIB : 20 Std : INT13 Results: ON Offsets : OFF
The 6103 makes it very simple for an operator to test a phone.

Prompts are given as the test progresses to ensure that the user is
informed of the step in the test. The status window describes exactly
what is happening - in this case Alerting Call Party.

Power control
Traffic
Go to
Power level 3
Power control
During conversation the base station periodically measures the power

it receives from the mobile. It can then instruct the mobile to adjust
its power, via a control channel as it moves in a cell. This helps
reduce the overall level of RF in a cell and leads to less chance of
one phone interfering with others.
With GSM, the mobile also measures received signal strength and
quality. This information is passed back to the base station so it can
adjust its power also. Power control for GSM is much finer than that
on analog systems.
GSM mobiles can adjust their power in 2dB steps from +13dBm
(20mW) to a maximum of +39dBm/8W for a class 2. In practice most
mobiles are class 2 (max. power = +39dBm/8W) and most hand
portables are class 4 (max. power = +33dBm/2W).
Phase II GSM specifications define four new power levels (PL16-
PL19) to allow for even smaller cells and hence better frequency re-
use.
DCS1800 and PCS1900 phones use different power levels : see the
tables in the section: Useful data.

Test Running : Power Levels/Steps 01 JAN 1996 12:00:00 Edit
Information Parameters
Test Status Fail : Measured Values Exceed Test Limits
Repeat
Step Number Requested Measured Error
Test
1 8 <27.0> dBm +27.2 dBm -0.2 dB
2 10 <23.0> dBm +19.6 dBm -3.4 dB
3 12 <19.0> dBm +21.8 dBm +2.8 dB
4 14 <15.0> dBm +12.9 dBm -2.1 dB
5 16 <11.0> dBm +7.9 dBm -3.1 dB
6 18 <7.0> dBm +119 dBm +4.9 dB
TCH ARFCN HOP TCH Slot 4

TCH Level -85.0 dBm Mobile Power Level ---
Status : Call Connected MT RXQUAL : 0 RXLEV : 21

EXIT
GPIB : 20 Std : INT 13 Results : OFF Offsets : ON
The Racal 6103 performs an automatic test that demonstrates the

power levels and provides the measured value and the error in dB.
Any results that do not meet those specified are highlighted for the
user.
Where test leads or fixtures introduce attenuation, an offset can be
added to the calculation to compensate. The offset is shown to be
ON in the screen above.

Timing advance
Traffic
Adjust Timing Traffic

advance to 63 bits
Signals must arrive at

BTS at correct time BTS
Timing advance
As a mobile moves around in a cell, the transmission time may get

shorter or longer. In order for the mobile burst to arrive at the BTS in
its allocated timeslot. The BTS orders the mobile to advance its
timing.
GSM mobiles can adjust their timing by up to 63 bits in one bit steps.
There are guard periods at the end of every standard burst, so small
errors in timing can be tolerated.
(Note: The maximum cell radius for GSM is approximately 35km (22
miles) as the propagation time to and from a mobile is approximately
0.5km per bit. 63 bits allows a propagation time of 233s ;
approximately 35km).

Handover
Call gets handed over to suitable BTS
Strong signal
Speech
Weak signal
Speech
Handover
What differentiates a cellular radio system from basic mobile radio is the
capacity for handover. As the user travels he will move from one cell to
another. When appropriate, the conversation is handed over to the next
base station. This process should be transparent to the user as a
simultaneous speech path is set up on the new BTS before the mobile
changes channel / timeslot.
In the GSM system the mobile provides information to the BTS by
measuring the level of the adjacent cells during the idle timeslots. This
information is reported to the BTS at least every 30 seconds so the
network can determine when a handover is needed and to where.
(Note: The required sensitivity for phones are - 102dBm handportable
GSM
- 104dBm other GSM
- 100dBm DCS1800 (class 1
&2
- 102dBm DCS1800 (class 3)
- 102dBm All PCS 1900

IMSI detached
Im switching off
Off button
IMSI detached
GSM phones send a signal (IMSI detached) to the network to inform

them they are being switched off. This saves the network paging for
phones that are not able to receive calls.
Note: It can also be useful when testing a phone as the signal can be
used to provide a test system indication that the phone testing has
finished.

How GSM works :the bigger picture and what needs testing
GSM the air interface

MSK modulation
GMSK modulation
Burst Timing
TX power
Useful part of burst
Burst structure
TDMA
Frequency hopping
Improved Tolerance to Fading
Speech coding
Vocoder technology
Error protection
Digital vs Analog
Authentication
Encryption
Measurements
Phase trajectory
Sensitivity
Bit errors and frame erasure
Voice loopback
Other measurements
Receiver measurements
Burst profile measurement
How GSM works: the bigger picture and what needs testing - Page 1
GSM - the air interface
GMSK modulation
TDMA & frame structure
Frequency hopping
Digitised speech
Encryption
The GSM air interface provides a number of new concepts, acronyms

and opportunities for measuring equipment. Fortunately the GSM
specification is well defined in the recommendations.
GMSK (Gaussian Minimum Shift Key) modulation is used to transmit
RF information.
RF information is sent as bursts of data, timeshared with other users
on the same channel (TDMA) Time Division Multiple Access.
Speech is digitised and then coded to reduce the actual number of
bits sent over the air.
Frequency hopping is used to improve performance in a multipath
fading environment
Encryption is used to ensure security & speech privacy.
MSK modulation
Q 0 t
MSK Modulation
Speech, data and signalling information is transmitted over the air as

digital information (i.e. 1s and 0s).
These 1s and 0s are modulated on to an RF carrier using GMSK
modulation.
The process initially involves changing the phase of the RF carrier. A
0 will produce a phase change of -90 deg and a 1 +90 deg. This is
MSK (minimum shift keying).
One advantage of MSK is that the RF Amplitude is constant; this is
less likely to produce distortion if their are any non-linearities in the
system.
GMSK modulation
Phase modulation
Phase MSK
phase
steps
GMSK
1 0 0 1 0 1 1 0 1 0 0 0 Time
time
GMSK modulation
The MSK modulated signal is effectively passed through a Gaussian

shaped filter to reduce the bandwidth of the signal. This is essential if
channel spacing is to be kept to a minimum.
GSM makes use of 0.3GMSK. This means that the BT (bandwidth:bit
rate) is 0.3. This design ensures that a channel spacing of 200 kHz is
possible.
Note: BT is bandwidth to bit period factor
B= bandwidth of the Gaussian filter
T= bit period (i.e.1/t = bit rate)
Burst timing
Previous 1 timeslot Next burst

burst
Guard time
8.25 bits
147 useful bits time
Commands to Advance (up to 63 bits)
Burst Timing
The phone will transmit its speech in one of eight time frames. This is
referred to as TDMA (Time Division Multiple Access).
Because it may be sharing a single carrier with several other users,
the timing of the transmitted burst must be controlled accurately. The
base station will advise the phone to advance its burst to take into
account the different propagation time over the air. This is done
once initial syncronisation is made.
To ensure proper syncronisation, Access bursts are sent initially to
ensure that data is not sent in an adjacent timeslot. Access bursts
are shortened by 60 bits and are sent by the phone until the BTS has
instructed it to advance its transmissions.
There is a guard period equivelant to 8.25 bits between each burst
(68.25 bits for access bursts), each speech burst has 3 tail bits at the
beginning and end which carry 000 information and allow time for
the burst to reach full power before sending meaningful data.
Tx power
4dB
1dB
-6dB
-1dB
-30dB
-70dB
t
0 3 6 147 bits
not to scale
Tx Power
As well as the timing of the burst, its shape is very important. There
is a power template defined in the GSM specifications that sets limits
for its shape and relative amplitude with time.
The flatness of the portion carrying the data must fit within a +/-1dB
window. The rising and falling edges must fit limits that ensure they
do not produce ringing and yet still allow enough time to convey the
data.
MultiMode : Power Profile 15 JAN 1996 11:24:57 TCH ARFCN
BER 62
10
0
Phase TCH Level
-10
Error -85.0 dBm
-20
d
B -30
TCH Slot
Summary -40 4
-50
-60 MS Power
Modulation
Spectrum -70 7
0 20 40 60 80 100 120 140
Bits
Audio
Current Min Max More...
Speech
Mode Input Power 30.285 dBm 30.273 dBm 30.328 dBm
EXIT
The above screen from the 6103 shows the entire length of the power
profile on a speech burst. The screen also displays the absolute
power level, also the minimum and maximum power over the useful
part of the burst.
All bursts must fit the power profile defined in GSM Rec 11.10. If
power ramps up or down too fast, interference might be caused in the
adjacent channel and cause interference to other users.
If the Ramp is too slow, then data may be lost from the burst or
adjacent timeslot interference may occur.
It is possible to examine the useful parts of the power burst using the
6103. Both the rising and falling edge may be examined in more
detail. The top of the burst may also be displayed in more detail
Burst structure
Mobile Transmit Burst - TCH
Sync
Sync
Speech
Speech Speech
Speech
000
000 Mid-
Mid- 000
000
Information
Information Information
Information
Amble
Amble
3 58 26 58 3 bits
Burst structure
Although there are some exceptions, the majority of bursts are made
up of Speech information, a syncronisation sequence and 3 tail bits at
each end.
The speech information is coded in a variety of different ways, and
will be explained later. It occupies 116 bits.
The syncronisation sequence is often referred to as a training
sequence or mid-amble. It consists of 26 bits of predefined data, that
can be decoded and then used as a reference for timing and
equalization.
The 3 tail bits at either end serve as guard bits between other time
slots.
TDMA
Base Station Transmit, Mobile Receive
11 22 33 44 55 66 77 00 11
Mobile Transmit Offset 3 slots
66 77 00 1 22 33 44 55 66
Adjacent Cell
Monitoring
TDMA
There is a delay of 3 time slots between the downlink from the BTS
and the uplinkfrom the phone. This allows a single synthesiser to be
employed in the phone as the transmit and receive timeslots do not
coincide. It also reduces the need for complex duplex filters
The phone is also able to monitor other channels during the idle slots.
during this time the radio monitors the signal strength of the adjacent
channels.
Improving resistance to fading
Improving tolerance to fading
Frequency hopping is a way of improving the tolerance to the effects

of multipath fading. This is where reflections of the main signal
combine to mix destructively: producing a signal fade.
Because this fading is frequency dependent, a fade on one channel
frequency may produce constructive mixing on another frequency.
By frequency hopping over a number of channels, the effects of
fading are reduced to a minimum, this means that the majority of time
fading will not be apparent as error correction can still function.
Frequency hopping
Frames
ARFCN
Channel
t
f
Frequency hopping
All mobiles have the capability of frequency hopping although it may

not always be used.
Frequency hopping can be switched on and off by the network.
Some networks may switch on the hopping in parts of the network
where multipath is a problem.
In hopping mode the phone will switch to a different ARFCN
(Absolute Radio Frequency Channel) after each burst according to a
predefined sequence.
Test : Sensitivity 14 DEC 1995 14:12:44
Accept
Parameter Value Default
TCH ARFCN 90 62
TCH Slot 1 4
Mobile Power Level 15 7
Hopping OFF OFF
Encryption OFF OFF
Initial Level -90.0 -90.0 dBm
Final Step Size 0.50 0.50 dB
Pass/Fail Threshold -102.0 -102.0 dBm
Sample Time 10 10 s
Test Pattern 1 1
FER Limit 0.200 0.200 %
Class Ib BER Limit 0.410 0.410 %
Class II BER Limit 2.440 2.440 %
Range : 0 to 31
T.A. : RXLEV: RXQUAL:

Cancel
GPIB : 20 Std: 10 MHz Results: Off Offsets : On
Frequency hopping
The 6103 has the ability to hop like the network. The hopping pattern
can be defined by the user and switched on and off as required.
Speech coding
13 bit /samples 104 kbits/s 13 kbits/s

@ 8k bit rate reduced to increased to
=104 kbits/s 13 kbit/s 22 kbit/s
Analog to Speech Error Protection

Speech
digital coder
converter
The speech goes through two distinct processes before it is

modulated onto the RF carrier.
First the analog speech is sampled at a rate of 8 kbits / s. Each
sample produces 13 bits of information: a total data rate of 104
kbits/s. If fhis were sent directly to the modulator the occupied
bandwidth required would be enormous.
A speech coder or vocoder is used to reduce the number of bits that
need to be sent. Vocoders are designed to produce acceptable
intelligent transfer of speech information, while minimising the amount
of data sent. There are a number of vocoders available today, and
more are being proposed with enhanced capability.
Vocoder technology
full rate 13 kbits /s

104 kbits /s
vocoder
sampled speech coded speech
half rate 6.5 kbits /s

104 kbits /s
vocoder
sampled speech coded speech
The original vocoder used for GSM is a full-rate 13kbit/s vocoder: A

half rate vocoder is also available, producing a rate of 6.5kbit/s.
Others are also in use, such as an enhanced full rate vocoder in the
US.
The GSM full rate coder reduces the 104 kbit/s rate down to an
effective 13 kbits/s. How it does this is beyond the scope of this
document, but put simply, the vocoder breaks down the speech in a
way that only the important elements of the speech are sent, allowing
the information to be decoded to an acceptable level. For example
silence in the signal would not require any data to be sent.
Reductions of 80% can be achieved by this process.
Note that all this processing does introduce a delay of approximately

65ms and can be tricked: try sending your favourite music track
across the network and you may well be disappointed.
Error protection
Class 1a bits = very important = add parity bits
Class 1b bits= quite important = code with Class 1a
Class 2 bits = not important = no correction
13 kbits/s rate increased to 22 kbits/s
So far the coded speech data would be unprotected from any

interference or impairements in the system, so error protection is
added.
Here the data is grouped into class Ia bits, Ib bits and class II bits.
The class Ia bits are the most important and are given parity
protection by adding 3 parity bits. They are then added to class Ib
bits and convolutionally coded to provide further correction and
detection. The class 2 bits are left unprotected.
This brings up the 13k bits/s data to 22.8 kbits/s.
If a class 1a bit cannot be corrected, the entire frame will be replaced
by silence, as these bits could cause disturbing sounds if
reconstituted incorrectly.
Digital vs Analog
100
90
80
70
60
50
40 Analog
30 Digital
Speech
20quality
10
0
-80 -85 -90 -95 -100 -105 -110 -115 -120 -125
Receive level (dBm)
Although this whole process seems very complex and cumbersome,

it produces the best compromise for transfer of speech to an
acceptable level in a radio network.
Compared to analog systems, digital systems tend to have no better
performance in good coverage areas, yet they out-perform them at
extremes of range.
The graph above shows how the GSM system, with all its processing
power, will maintain a conversation far beyond an analog TACS
system.
Authentication
random number
(Ki & random number) A3 algorithm
Every time the phone registers or makes a call, an authentication

process takes place.
A random number is sent from the base station. This number is
combined with another number (or key) called a Ki.
The Ki is a number held on the SIM that is unknown to the user. The
combination of the Ki, the random number and the A3 algorithm
produces a number over the air that the network can test.
This process ensures that the system is very secure, as every call set
up requires an acknowledgement before the call can be processed.
This method also ensures that the Ki is never sent over the air.
The network can also assign a TMSI (Temporary Mobile Subscriber
Identity) ensuring the mobiles true identitiy is not used for
subsequent call set ups.
Encryption is not always used, it can be switched on and off by the
network.
Encryption provides a secure way of further encoding the speech, to
prevent eavesdropping over the air. Another algorithm (A8)
generates a cipher key (Kc) from the random number, which is then
used to encrypt all the following data.
Measurements
Phase Trajectory
Tx Power
Sensitivity
Voice Loopback
Measurements
As with most tranceivers, measurement are made on the transmitter,

receiver and the speech path.
The phase relationship of a signal in GSM is very important. Any test
equipment must be able to measure both peak and RMS phase
errors and in order to perform any diagnostics, look at the relationship
during the burst.
Phase Trajectory
Phase
Phase Error
Bits
Ideal Phase
Actual Phase
Frequency
Error
Phase Trajectory
The modulation accuracy is measured by comparing the actual phase

trajectory with the theoretical trajectory over several bursts.
Large deviations will result in bit errors, so a fairly tight limit is placed
on the phone. Less than 20 degrees peak and less than 5 degrees
RMS is required for the phone to meet specification.
Mobile frequency is adjusted in the mobile by synchronising from the
FCCH (Frequency Correction CHannel) on the BCCH (Broadcast
Control Channel). The error must be less than 0.1ppm.
Sensitivity
Test System
Data
Data
Signal
Signal Pattern
Pattern
Generator
Generator Generator
Generator
Measuring
Measuring BER
BER
Receiver
Receiver Software
Software
Rx data
= Tx
2nd
2nd
test SIM Signal
Signal
Generator
Generator
To measure the sensitivity of a phone, the GSM specification

provides a test loopback mode in all phones. This can be invoked by
using a test SIM and an instruction over the air.
The test SIM provides the loopback facility which turns all received
signals back onto the transmitter path so that bit errors can be
measured. The loopback is provided after the channel coding and
does not include the vocoder.
The Racal 6103 produces a pseudo-random data pattern that is
modulated by the internal signal generator, the phone is put into
loopback mode by sending the correct command and then sensitivity
can be measured. This is done by reducing the level of the RF
signal and measuring the errors. The bit error rate can be used to
determine the sensitivity of the phone.
Note: Some phones use the spare slots to monitor the control
channel and maintain frequency control, so the 6103 provides a
simulated signal during these slots, so that the phone still apparently
sees a control channel.
Bit errors and frame erasure
BER for class Ia, Ib & II
RBER for class Ib & II
FER (Frame Erasure Rate)
Because some bits are given different levels of protection against

errors, it is not straight forward to just measure bit error rate on all
received bits.
RBER (Residual Bit Error Rate) is defined as the BER in all good
frames. A good frame is defined as one where the parity in the class
1a bits were not received in error.
Where errors are received in class Ia bits, frames are erased and
replaced eirther data that is predicted from previous frames, or in
severe cases muted audio.
Measurement of the number of frames erased or FER (Frame
Erasure Rate) can be made.
MultiMode : BER 15 JAN 1996 11:24:57 Burst
Limits ALL
Current Min Max Samples
Test Pattern
FER 2.50 % 1.29 % 3.53 % 50
8
CIb 2.50 % 2.29 % 3.53 % 6600
CII 2.50 % 2.29 % 3.53 % 3900

Freq. Offset
+120 Hz
Timing Adv.
24 bits
Clear
Min/Max More...
Status : Idle RXQUAL : 0 RXLEV : 23

EXIT
The above diagram shows the three measurements of FER, Class Ib

and Class II bit error rates. Where limits are exceeded, the results
field is highlighted.
RXLEV measurement of the RF signal strength
RXQUAL measurement of the bit error rate
Phone can measure up to 6 neighbour cells
During a conversation, the mobile makes 2 measurements on the

current physical traffic channel (TCH). These two measurements are
RXLEV, the level of the traffic channel and RXQUAL, the quality of
the traffic channel (determined from the bit error rate).
There is also time for the phone to make measurement on up to 6
neighbouring cells to determine if there is a better channel.
RXLEV must be within: +/-4dB at levels from -110 to -70 dBm
and +/-6dB at levels from -70 to -48 dBm.
Test Running : Receiver Test 15 JAN 1996 11:24:57 Edit
Information Parameters
Test Status PASS
Repeat
Measurement Samples Events Ratio Test
FER 50 0 0.000 %
CIb 6600 0 0.000 %
CII 3900 11 0.282 %
Expected Measured Error

RXLEV : 8.5 (-102.0 dBm) 6.0 (-104.5 dBm) -2.5
RXQUAL : 1.0 (0.282 %) 0.0 (0.141 %) -1.0
TCH ARFCN HOP TCH Slot 4

TCH Level -102.0 dBm Mobile Power Level 7

EXIT
Receiver test results
Producing an accurate signal from the test equipment allows the

measurement produced by the phone to be compared and any errors
noted.
The effect of having poor measurement by the phone could produce
dropped calls on the network.
The above screen makes this test very simple as the expected and
measured values are displayed side by side with an error
calculation.
Voice loopback
Test System
Signal
Signal
Generator
Generator
Speech
Speech
Data
Data
Buffer
Buffer
Measuring
Measuring
Receiver
Receiver
The 6103 also provides a talkback mode, where speech from the
phone is stored in a buffer and then retransmitted back to the phone
after a few seconds. This allows a subjective assessment of the
speech path in both directions.
Additionally, speech phrases can be saved as data on a memory
card, and then replayed as desired.
Where there is a fault in one of the transmit or receive paths,
Standard speech phrases can be played back from the memory card
via the 6103 to determine which path is faulty.
Note: Because a vocoder is used, sending and measuring a 1 kHz
tone, as in analog systems, would not give a meaningful result.
MultiMode : Voice Loopback 15 JAN 1996 11:24:57 TCH ARFCN
BER
62
Phase TCH Level

Error -85.00 dBm
Power TCH Slot

Voice Loopback
Profile 4
Speak into mouthpiece to assess mobile's performance.

Modulation MS Power
Spectrum 2
Summary More...

EXIT
Multimode : voice loopback
The 6103 has a number of tests that allow subjective assessment of

the phones audio paths. One test is the Voice loopback. This test
can be selected manually or included in an automatic test sequence.
In the case of multimode the RF parameters can be viewed while the
looped back voice is monitored.
Other measurements
Power Steps
Timing Advance
Protocol
Registration, Authentication
Call Set up
Handover
Encryption
Doppler Shift
Fax and Data
The 6103 is able to put the phone into conversation mode and then
command it to change to all power levels. The main RF port on the
6103 is able to measure all power levels and then compare the
results with the defined standards.
Timing advance can be excercised either manually, by setting an
advance or by using the automatic test included.
A variety of impairements can be added during the RF testing such

as doppler shift, hopping and with a second 6103 or signal
generaotor, co channel and adjacent channel rejection.
The availability of Fax and Data services on GSM presents a new set
of testing problems. Probably the most important requirement is to
prove the correct function of the services under varying signal
conditions, but above all is must be easy to use.
MultiMode:Summary 15 JAN 1996 11:24:57 Burst
Limits ALL
Class II BER 0 5 0.00 %

Test Pattn
RXQUAL : 0 (0.0% : 0.2 %) RXLEV : 23 (-88 : -87 dBm) 1
Input Power 23 35 28.02 dBm

Freq. Offset
RMS Ph Err 0 10 3.35 Deg 0 Hz
Peak Ph Err 0 40 9.99 Deg

Timing Adv.
Freq. Err -200 200 31.08 Hz 0 bits
Timing Offset -0.29 bits

Power Profile Pass Mod. Spectrum --- More...

EXIT
Multimode:Summary
For faultfinding, a comprehensive set of measurements is provided

on one screen. Limits are shown as arrowheads and the bar graphs
change colour if a limit is exceeded.
The update of the screen makes this multmode a very helpful;
screen for diagnostics or phones.
When any parameters are changed, the 6103 automatically
generates the necessary protocol, making it very simple to use.
6103 Mobile test set
6103 Mobile test set
The 6103 is an easy to use, fully integrated Test Set optimized for
maintenance and servicing of GSM, DCS1800 and PCS1900 mobile
telephones.
It has a comprehensive modulation analyser for alignment and
diagnosticsand has fast measurement capability with integrated test
sequences.
The large, bright LCD display provides graphic and numeric displays.
In addition to speech testing cell broadcast and point to point short
message service testing is included. The no button start test is the
ultimate for simplicity of operation.
Fax
Fax and
and data
data testing
testing
PC or equivalent
Mobile
6103
Hayes Modem
PC or Fax RF
6103
MEMORY
CARD
Memory Card
256k
The Racal Instruments 6103 addresses fax and data testing by

emulating the GSM network right up to the far end terminal. This
allows a high degree of flexibility and also allows a number of fax
combinations to be tried.
For data calls, files can be transferred from the instruments memory
card or from an external PC/device via an RS232 port. Data can be
transferred in either transparent or non-transparent mode at 2400,
4800 or 9600 baud.
For fax calls the 6103 uses industry standard modem commands
which allows it to interface to a PC running commonly available fax
packages.
6103 Test Set - Interfaces
GPIB
6103 RS232
Parallel Printer
Test sequences
2 x PCMCIA Slots
6103 test set - interfaces
As standard, the 6103 comes equipped to provide results in a number

of ways. Control is provided by the GPIB interface.
The instrument also supports a form of BASIC. Using this language it
is possible to create test programs with custom tests, limits and
printouts.
Phase 2 type approval
TTCN Results
2 x 6103
GSM 6103
0252 625
TEST
7 8 9
4 5 6
1 2 3
* 0 #
6103
Phase 2 type approval
This type approval system consists of 2 6103 Digital Radio Test Sets
controlled by a PC.
To provide the rapid and coherent introduction of Phase 2, the GSM

MoU required the developement of a low cost, Stand Alone Tester
based upon off-the-shelf hardware. The tester had to allow for
conformance testing of mobile stations and support over 150 GSM
11.10 test cases, written in the TTCN (Tree and Tabular Combined
Notation) test specification language which is used ofr the definition
of Abstract Test Suites (ATS) under international standard ISO 9646
Part 3.
Cray systems PC controller
User
Control
Test
Equipment
TTCN
Input
Man
ManMachine
MachineInterface
Interface
TTCN Test Analysis
Library
Compiler Controller & Report
Software
Operating
OperatingSystem
System--Windows
Windows
PC
PCHardware
Hardware
Cray systems PC controller
The RF outputs of these two devices are combined and applied to the
mobile under test, with the test results presented on the PC Controller
or to networked systems.
The Stand Alone Tester is an ideal test solution for a variety of users,
from GSM test houses for the performance of formal type approval
accreditation testing, to network operators and manufacturers of
mobile equipment.
Operators will also use the Stand Alone Tester to examine mobile
stations which are perhaps giving an unexpected response to the
network. This will help these organisations pinpoint problems on the
network and/or discover operational difficulties with certain models of
mobile telephone, thereby improving the service to users.
How GSM works: a BTSs perspective and
what needs testing
U or Air interface
A-bis
BTS
BTS BSC
BSC
Elements of the GSM Network

Test requirements
Production test
Commissioning and installation
Live testing
What does the 6113 do ?
Typical test requirements
6113 applications
How GSM works: a BTSs perspective and what needs testing - Page 1
Elements of the GSM Network
U or Air interface
A
A-bis
BTS
BTS
MSC
MSC
BSC
BSC (Switch)
(Switch)
2.048Mb/s or 1.544Mb/s
PSTN
Before discussing base station testing, its important to understand

the basic elements of the system.
The BTS (Base Station Transceiver) is responsible for

communicating with the mobiles over the radio interface.
The BTS lacks the intelligence to manage the calls: this is

performed by the BSC (Base Station Controller). The
communication between the BTS and the BSC is an ISDN compatible
2.048 Mbit/s (E1) or 1.544 Mbit/s (T1) link. To control the BTS, the
BSC uses manufacturer specific commands on this link. This is the
A-bis interface.
The connection from the BSC to the PSTN is completely standard

and allows more regular telecom links to be used.
Test requirements
Research & Development

Production & Factory Test
Installation & Commissioning
Field Service & Optimization
Throughout the life of a BTS it will need to be tested in different ways.
During R&D traditional test equipment can be used, however for

protocol development a protocol analyzer or an interface emulator is
required.
During production and installation the other elements of the network

are not present, hence A-bis emulation is advantageous.
Once commissioned some form of in-service testing is required.
Production test
A-bis
A-bis XXXX - BTS RF interface
interface
A-bis interface
BTS code
download
BTS control
Bit error rate
RX_LEV/RX_QUAL
BTS error reports
For production testing the BTS has to be controlled so that it can

transmit, receive and perform correct signalling.
This can be achieved by proprietary control signals via a

maintenance terminal or by supplying the correct A-bis messages.
The later method has the advantage that the A-bis interface is
exercised as well as the RF.
A-bis protocols vary from manufacturer to manufacturer, and model to

model. Only by working closely with manufacturers can test
equipment be developed to meet these protocols.
Commissioning and
installation
GSM, DCS1800 or PCS1900
XXXX - BTS
X X
A-bis RF
BSC
X X
6113
6113
When commissioning base stations, it is very likely that the A-bis link
is not available. Even if it were the control of the BTS would still be
cumbersome.
A-bis control allows the BTS to be tested in isolation and can even
allow on-air trials with test network signals.
Live testing
XXXX - BTS
BSC RF
GSM, DCS1800 or PCS1900

6113
6113
Once installed there is a great reluctance to take a BTS out of service

simply to test it. Live testing offers a slightly more limited, but
convenient, method of routine testing.
In order to access the correct channels and ensure consistent results,

the test equipment could emulate a mobile and set up a live call.
The A-bis connection can still be used if receiver bit error rates are to
be measured.
What does the 6113 do ?
bIt verifies performance to GSM

recommendations (11.20, 05.05 etc.)
bIndependent evaluation of RF performance
bReduces BTS commissioning times
bImproves the BTS roll out rate
bIt reduces BTS downtime during faultfinding
The 6113 meets the requirements of GSM recommendations and

provides an independent evaluation of the RF performance of the
BTS.
Test times are remarkably short: often the code download to the BTS
may take longer than the test.
By keeping records of the BTS performance, degradation can be

monitored and corrective action made before it gets too serious.
When new network roll out times are measured in months rather
than years, fast authoritative testing is essential.
Typical test requirements
Functional Transmitter Receiver

A-bis link tests Cell control channel Bit error rate (BER)
Code download Bit error rate (BER) TCH Absolute sensitivity
Configure BTS Power RACH sensitivity
Reset BTS Power steps Timing advance
Special functions Rx level
Power control
Rx quality
Power profile
Encryption
Phase error
Frequency error
Modulation spectrum
The above shows the typical range of parameters that network

operators and manufacturers would test. The requirements are very
similar to a mobile. The main difference is that with a mobile the
control is transmitted over the air interface. The BTS requires control
from the A-bis.
6113 applications
A-bis RF
A.I.M.E.
BSC BTS
6113
6113
R&D and System Test
A-bis Monitor A-bis Control BOSS
6113 6113 6113

6113 6113 6113
System fault Installation and Base station On air

diagnosis Commissioning Service System
Racal Instruments 6113 digital radio test set, has been designed to
provide a test capability in all of the above scenarios.
GLOSSARY OF TERMS & ABBREVIATIONS
ARFCN Absolute RF Channel Number. A number in the range

1 to 124 (GSM) or 512 to 885 (DCS 1800) which
defines the absolute radio frequency channel number.
AGCH Access Grant CHannel

CH
BA BCCH Allocation. The radio frequency channels

allocated in a cell for BCCH transmission.
BCC Base Station Colour Code
BCCH Broadcast Control CHannel

CH
BCCH_FREQ_NCELL Frequency of the RF carrier on which the BCCH of a

neighbouring cell is transmitted.
BER Bit Error Ratio
BFI Bad Frame Indicator
BS_AG_BLKS_RES The number of blocks on each common control

channel reserved for access grant messages.
BSIC Base Transceiver Station Identity Code
BS_PA_MFRMS The number of multiframes between two transmissions

of the same paging message to MSs of the same
paging group.
BTS Base Transceiver Station
Burst A period of modulated carrier less than one timeslot.

The physical content of a timeslot.
CA Cell Allocation. The radio frequency channels

allocated to a particular cell
CAT Cell Allocation Table
CBCH Cell Broadcast

B CHannel
CH
CCH Cell Control Channel
CCCH Common Control CHannel

CH
CCCH_GROUP Group of MSs in idle mode.
CELL Geographical area within which a defined set of

channels is provided.
CELL_BAR_ACCESS Cell access barred parameter.
CELL_RESELECT_HYSTERESIS The RXLEV hysteresis required for cell reselection.
CEPT Conference of European Posts & Telecommunications

Class lA, lB, ll Classification of speech encoder bits depending on the
degree of protection needed. Class lA and Class lB
bits have protection; Class ll bits have no protection.
Error detection is performed on Class lA bits.
DAI Digital Audio Interface
DTX Discontinuous Transmission. Means of saving battery

power (e.g. in HPUs) and reducing interference by
automatically switching the transmitter off when no
speech or data are to be sent.
ESN Electronic Serial Number
ETSI European Telecommunications Standards Institute
FACCH Fast Associated Control CHannel

CH
FCCH Frequency Correction CHannel

CH
FER Frame Erasure

E Rate
GMSK Gaussian Minimum Shift Key
GPIB General Purpose Interface Bus
GSM Global System for Mobile communications
HPU Hand Portable Unit
HSN Hopping Sequence Number
IMEI International Mobile Equipment Identity
IMSI International Mobile Subscriber Identity
ISDN Integrated Services Digital Network
ITA Interim Type Approval
Kc Cipher Key Sequence
Ki Subscriber Authentication Key
LAI Location Area Identity
MAHO Mobile Assisted Hand Over
MAIO Mobile Allocation Index Offset
MAT Mobile Allocation Table
MIN Mobile Identity Number
MMI Man Machine Interface
MS Mobile Station
MSC Mobile Switching Centre

MSK Minimum Shift Keying
MS_TXPWR_MAX_CCH Maximum allowed transmitted RF power for MSs to

access the system until commanded otherwise.
PCH Paging CHannel

CH
PID Protocol IDentifier

ID
PIN Personal Identification Number
PLMN Public Land Mobile Network
PLMN_PERMITTED PLMN permitted for handover purposes.
RACH Random Access CHannel

CH
RAND Random number used during Authentication.
RBER Residual Bit Error Rate
RPE-LTP Regular Pulse Excitation - Long Term Prediction. The

method used to of code and decode speech for the
original GSM vocoder.
RXLEV Received Signal LEVel

LEV parameter. A measure of the
mean received signal level.
RXLEV_ACCESS_MIN The minimum RXLEV at a MS for access to a cell.
SACCH Slow Associated Control Channel
SACCH_TF Slow Associated Control Channel - Traffic Full Rate
SAPI Service Access Point Indicator
SDCCH Stand Alone Dedicated Control CHannel

CH
SCH Synchronisation CHannel

CH
SIM Subscriber Identity Module
SMS Short Message

M Service
S
SRES Signature RESponse

RES
TCH Traffic CHannels.

CH Channels that carry user speech or
data.
TDM Time Division Multiplexing
TDMA Time Division Multiple Access
TMSI Temporary Mobile Subscriber Identity
TN Timeslot Number
CHANNEL NUMBER/FREQUENCY CHARTS
E-GSM CHART 1 -- DOWNLINK (Base Station To Mobile)
CHANNEL DOWNLINK FREQUENCIES

NUMBERS (MHz)
0 935.000
1-5 935.200 935.400 935.600 935.800 936.000
6 - 10 936.200 936.400 936.600 936.800 937.000
11 - 15 937.200 937.400 937.600 937.800 938.000
16 - 20 938.200 938.400 938.600 938.800 939.000
21 - 25 939.200 939.400 939.600 939.800 940.000
26 - 30 940.200 940.400 940.600 940.800 941.000
31 - 35 941.200 941.400 941.600 941.800 942.000
36 - 40 942.200 942.400 942.600 942.800 943.000
41 - 45 943.200 943.400 943.600 943.800 944.000
46 - 50 944.200 944.400 944.600 944.800 945.000
51 - 55 945.200 945.400 945.600 945.800 946.000
56 - 60 946 200 946 400 946.600 946.800 947.000
61 - 65 947.200 947.400 947.600 947.800 948.000
66 - 70 948.200 948.400 948.600 948.800 949.000
71 - 75 949.200 949.400 949.600 949.800 950.000
76 - 80 950.200 950.400 950.600 950.800 951.000
81 - 85 951.200 951.400 951.600 951.800 952.000
86 - 90 952.200 952.400 952.600 952.800 953.000
91 - 95 953.200 953.400 953.600 953.800 954.000
96 - 100 954.200 954.400 954.600 954.800 955.000
101 - 105 955.200 955.400 955.600 955.800 956.000
106 - 110 956.200 956.400 956.600 956.800 957.000
111 - 115 957.200 957.400 957.600 957.800 958.000
116 - 120 958.200 958.400 958.600 958.800 959.000
121 - 124 959.200 959.400 959.600 959.800
975 - 979 925.200 925.400 925.600 925.800 926.000

980 - 984 926.200 926.400 926.600 926.800 927.000
985 - 989 927.200 927.400 927.600 927.800 928.000
990 - 994 928.200 928.400 928.600 928.800 929.000
995 - 999 929.200 929.400 929.600 929.800 930.000
1000 - 1004 930.200 930.400 930.600 930.800 931.000
1005 - 1009 931.200 931.400 931.600 931.800 932.000
1010 - 1014 932.200 932.400 932.600 932.800 933.000
1015 - 1019 933.200 933.400 933.600 933.800 934.000
1020 - 1023 934.200 934.400 934.600 934.800
Useful Data - GSM P-1

E-GSM CHART 2 -- UPLINK (Mobile To Base Station)
CHANNEL UPLINK FREQUENCIES

NUMBERS (MHz)
0 890.000
1-5 890.200 890.400 890.600 890.800 891.000
6 - 10 891.200 891.400 891.600 891.800 892.000
11 - 15 892.200 892.400 892.600 892.800 893.000
16 -20 893.200 893.400 893.600 893.800 894.000
21 - 25 894.200 894.400 894.600 894.800 895.000
26 - 30 895.200 895.400 895.600 895.800 896.000
31 - 35 896.200 896.400 896.600 896.800 897.000
36 - 40 897.200 897.400 897.600 897.800 898.000
41 - 45 898.200 898.400 898.600 898.800 899.000
46 - 50 899.200 899.400 899.600 899.800 900.000
51 - 55 900.200 900.400 900.600 900.800 901.000
56 - 60 901.200 901.400 901.600 901.800 902.000
61 - 65 902.200 902.400 902.600 902.800 903.000
66 - 70 903.200 903.400 903.600 903.800 904.000
71 - 75 904.200 904.400 904.600 904.800 905.000
76 - 80 905.200 905.400 905.600 905.800 906.000
81 - 85 906.200 906.400 906.600 906.800 907.000
86 - 90 907.200 907.400 907.600 907.800 908.000
91 - 95 908.200 908.400 908.600 908.800 909.000
96 - 100 909.200 909.400 909.600 909.800 910.000
101 - 105 910.200 910.400 910.600 910.800 911.000
106 - 110 911.200 911.400 911.600 911.800 912.000
111 - 115 912.200 912.400 912.600 912.800 913.000
116 - 120 913.200 913.400 913.600 913.800 914.000
121- 124 914.200 914.400 914.600 914.800
975 - 979 880.200 880.400 880.600 880.800 881.000
980 - 984 881.200 881.400 881.600 881.800 882.000
985 - 989 882.200 882.400 882.600 882.800 883.000
990 -994 883.200 883.400 883.600 883.800 884.000
995 - 999 884.200 884.400 884.600 884.800 885.000
1000 - 1004 885.200 885.400 885.600 885.800 886.000

1005 - 1009 886.200 886.400 886.600 886.800 887.000
1010 - 1014 887.200 887.400 887.600 887.800 888.000
1015 - 1019 888.200 888.400 888.600 888.800 889.000
1020 - 1023 889.200 889.400 889.600 889.800

DCS 1800 CHART 1 -- DOWNLINK (Base Station To Mobile)

NUMBERS (MHz)
512 - 515 1805.2 1805.4 1805.6 1805.8

516 - 520 1806.0 1806.2 1806.4 1806.6 1806.8
521 - 525 1807.0 1807.2 1807.4 1807.6 1807.8
526 - 530 1808.0 1808.2 1808.4 1808.6 1808.8
531 - 535 1809.0 1809.2 1809.4 1809.6 1809.8
536 - 540 1810.0 1810.2 1810.4 1810.6 1810.8
541 - 545 1811.0 1811.2 1811.4 1811.6 1811.8
546 - 550 1812.0 1812.2 1812.4 1812.6 1812.8
551 - 555 1813.0 1813.2 1813.4 1813.6 1813.8
556 - 560 1814.0 1814.2 1814.4 1814.6 1814.8
561 - 565 1815.0 1815.2 1815.4 1815.6 1815.8
566 - 570 1816.0 1816.2 1816.4 1816.6 1816.8
571 - 575 1817.0 1817.2 1817.4 1817.6 1817.8
576 - 580 1818.0 1818.2 1818.4 1818.6 1818.8
581 - 585 1819.0 1819.2 1819.4 1819.6 1819.8
586 - 590 1820.0 1820.2 1820.4 1820.6 1820.8
591 - 595 1821.0 1821.2 1821.4 1821.6 1821.8
596 - 600 1822.0 1822.2 1822.4 1822.6 1822.8
601 - 605 1823.0 1823.2 1823.4 1823.6 1823.8
606 - 610 1824.0 1824.2 1824.4 1824.6 1824.8
611 - 615 1825.0 1825.2 1825.4 1825.6 1825.8
616 - 620 1826.0 1826.2 1826.4 1826.6 1826.8
621 - 625 1827.0 1827.2 1827.4 1827.6 1827.8
626 - 630 1828.0 1828.2 1828.4 1828.6 1828.8
631 - 635 1829.0 1829.2 1829.4 1829.6 1829.8
636 - 640 1830.0 1830.2 1830.4 1830.6 1830.8

641 - 645 1831.0 1831.2 1831.4 1831.6 1831.8
646 - 650 1832.0 1832.2 1832.4 1832.6 1832.8
651 - 655 1833.0 1833.2 1833.4 1833.6 1833.8
656 - 660 1834.0 1834.2 1834.4 1834.6 1834.8
661 - 665 1835.0 1835.2 1835.4 1835.6 1835.8
666 - 670 1836.0 1836.2 1836.4 1836.6 1836.8
671 - 675 1837.0 1837.2 1837.4 1837.6 1837.8
676 - 680 1838.0 1838.2 1838.4 1838.6 1838.8
681 - 685 1839.0 1839.2 1839.4 1839.6 1839.8
686 - 690 1840.0 1840.2 1840.4 1840.6 1840.8
691 - 695 1841.0 1841.2 1841.4 1841.6 1841.8
696 - 700 1842.0 1842.2 1842.4 1842.6 1842.8
701 - 705 1843.0 1843.2 1843.4 1843.6 1843.8
706 - 710 1844.0 1844.2 1844.4 1844.6 1844.8

DCS 1800 CHART 2 -- DOWNLINK (Base Station To Mobile)(continued)

NUMBERS (MHz)
711 - 715 1845.0 1845.2 1845.4 1845.6 1845.8

716 - 720 1846.0 1846.2 1846.4 1846.6 1846.8
721 - 725 1847.0 1847.2 1847.4 1847.6 1847.8
726 - 730 1848.0 1848.2 1848.4 1848.6 1848.8
731 - 735 1849.0 1849.2 1849.4 1849.6 1849.8
736 - 740 1850.0 1850.2 1850.4 1850.6 1850.8
741 - 745 1851.0 1851.2 1851.4 1851.6 1851.8
746 - 750 1852.0 1852.2 1852.4 1852.6 1852.8
751 - 755 1853.0 1853.2 1853.4 1853.6 1853.8
756 - 760 1854.0 1854.2 1854.4 1854.6 1854.8
761 - 765 1855.0 1855.2 1855.4 1855.6 1855.8

766 - 770 1856.0 1856.2 1856.4 1856.6 1856.8
771 - 775 1857.0 1857.2 1857.4 1857.6 1857.8
776 - 780 1858.0 1858.2 1858.4 1858.6 1858.8
781 - 785 1859.0 1859.2 1859.4 1859.6 1859.8
786 - 790 1860.0 1860.2 1860.4 1860.6 1860.8
791 - 795 1861.0 1861.2 1861.4 1861.6 1861.8
796 - 800 1862.0 1862.2 1862.4 1862.6 1862.8
801 - 805 1863.0 1863.2 1863.4 1863.6 1863.8
806 - 810 1864.0 1864.2 1864.4 1864.6 1864.8
811 - 815 1865.0 1865.2 1865.4 1865.6 1865.8
816 - 820 1866.0 1866.2 1866.4 1866.6 1866.8
821 - 825 1867.0 1867.2 1867.4 1867.6 1867.8
826 - 830 1868.0 1868.2 1868.4 1868.6 1868.8
831 - 835 1869.0 1869.2 1869.4 1869.6 1869.8
836 - 840 1870.0 1870.2 1870.4 1870.6 1870.8
841 - 845 1871.0 1871.2 1871.4 1871.6 1871.8
846 - 850 1872.0 1872.2 1872.4 1872.6 1872.8
851 - 855 1873.0 1873.2 1873.4 1873.6 1873.8
856 - 860 1874.0 1874.2 1874.4 1874.6 1874.8
861 - 865 1875.0 1875.2 1875.4 1875.6 1875.8
866 - 870 1876.0 1876.2 1876.4 1876.6 1876.8
871 - 875 1877.0 1877.2 1877.4 1877.6 1877.8
876 - 880 1878.0 1878.2 1878.4 1878.6 1878.8
881 - 885 1879.0 1879.2 1879.4 1879.6 1879.8

DCS 1800 CHART 3 -- UPLINK (Mobile to Base Station)

NUMBERS (MHz)
512 - 515 1710.2 1710.4 1710.6 1710.8

516 - 520 1711.0 1711.2 1711.4 1711.6 1711.8
521 - 525 1712.0 1712.2 1712.4 1712.6 1712.8
526 - 530 1713.0 1713.2 1713.4 1713.6 1713.8
531 - 535 1714.0 1714.2 1714.4 1714.6 1714.8
536 - 540 1715.0 1715.2 1715.4 1715.6 1715.8
541 - 545 1716.0 1716.2 1716.4 1716.6 1716.8
546 - 550 1717.0 1717.2 1717.4 1717.6 1717.8
551 - 555 1718.0 1718.2 1718.4 1718.6 1718.8
556 - 560 1719.0 1719.2 1719.4 1719.6 1719.8
561 - 565 1720.0 1720.2 1720.4 1720.6 1720.8
566 - 570 1721.0 1721.2 1721.4 1721.6 1721.8
571 - 575 1722.0 1722.2 1722.4 1722.6 1722.8
576 - 580 1723.0 1723.2 1723.4 1723.6 1723.8
581 - 585 1724.0 1724.2 1724.4 1724.6 1724.8
586 - 590 1725.0 1725.2 1725.4 1725.6 1725.8
591 - 595 1726.0 1726.2 1726.4 1726.6 1726.8
596 - 600 1727.0 1727.2 1727.4 1727.6 1727.8
601 - 605 1728.0 1728.2 1728.4 1728.6 1728.8
606 - 610 1729.0 1729.2 1729.4 1729.6 1729.8
611 - 615 1730.0 1730.2 1730.4 1730.6 1730.8
616 - 620 1731.0 1731.2 1731.4 1731.6 1731.8
621 - 625 1732.0 1732.2 1732.4 1732.6 1732.8
626 - 630 1733.0 1733.2 1733.4 1733.6 1733.8
631 - 635 1734.0 1734.2 1734.4 1734.6 1734.8
636 - 640 1735.0 1735.2 1735.4 1735.6 1735.8
641 - 645 1736.0 1736.2 1736.4 1736.6 1736.8
646 - 650 1737.0 1737.2 1737.4 1737.6 1737.8
651 - 655 1738.0 1738.2 1738.4 1738.6 1738.8
656 - 660 1739.0 1739.2 1739.4 1739.6 1739.8
661 - 665 1740.0 1740.2 1740.4 1740.6 1740.8
666 - 670 1741.0 1741.2 1741.4 1741.6 1741.8
671 - 675 1742.0 1742.2 1742.4 1742.6 1742.8
676 - 680 1743.0 1743.2 1743.4 1743.6 1743.8
681 - 685 1744.0 1744.2 1744.4 1744.6 1744.8
686 - 690 1745.0 1745.2 1745.4 1745.6 1745.8
691 - 695 1746.0 1746.2 1746.4 1746.6 1746.8
696 - 700 1747.0 1747.2 1747.4 1747.6 1747.8
701 - 705 1748.0 1748.2 1748.4 1748.6 1748.8
706 - 710 1749.0 1749.2 1749.4 1749.6 1749.8

DCS 1800 CHART 4 -- UPLINK (Mobile to Base Station)(Continued)

NUMBERS (MHz)
711 - 715 1750.0 1750.2 1750.4 1750.6 1750.8

716 - 720 1751.0 1751.2 1751.4 1751.6 1751.8
721 - 725 1752.0 1752.2 1752.4 1752.6 1752.8
726 - 730 1753.0 1753.2 1753.4 1753.6 1753.8
731 - 735 1754.0 1754.2 1754.4 1754.6 1754.8
736 - 740 1755.0 1755.2 1755.4 1755.6 1755.8
741 - 745 1756.0 1756.2 1756.4 1756.6 1756.8
746 - 750 1757.0 1757.2 1757.4 1757.6 1757.8
751 - 755 1758.0 1758.2 1758.4 1758.6 1758.8
756 - 760 1759.0 1759.2 1759.4 1759.6 1759.8
761 - 765 1760.0 1760.2 1760.4 1760.6 1760.8
766 - 770 1761.0 1761.2 1761.4 1761.6 1761.8
771 - 775 1762.0 1762.2 1762.4 1762.6 1762.8
776 - 780 1763.0 1763.2 1763.4 1763.6 1763.8
781 - 785 1764.0 1764.2 1764.4 1764.6 1764.8
786 - 790 1765.0 1765.2 1765.4 1765.6 1765.8
791 - 795 1766.0 1766.2 1766.4 1766.6 1766.8
796 - 800 1767.0 1767.2 1767.4 1767.6 1767.8
801 - 805 1768.0 1768.2 1768.4 1768.6 1768.8
806 - 810 1769.0 1769.2 1769.4 1769.6 1769.8
811 - 815 1770.0 1770.2 1770.4 1770.6 1770.8
816 - 820 1771.0 1771.2 1771.4 1771.6 1771.8
821 - 825 1772.0 1772.2 1772.4 1772.6 1772.8
826 - 830 1773.0 1773.2 1773.4 1773.6 1773.8
831 - 835 1774.0 1774.2 1774.4 1774.6 1774.8
836 - 840 1775.0 1775.2 1775.4 1775.6 1775.8
841 - 845 1776.0 1776.2 1776.4 1776.6 1776.8
846 - 850 1777.0 1777.2 1777.4 1777.6 1777.8
851 - 855 1778.0 1778.2 1778.4 1778.6 1778.8
856 - 860 1779.0 1779.2 1779.4 1779.6 1779.8
861 - 865 1780.0 1780.2 1780.4 1780.6 1780.8
866 - 870 1781.0 1781.2 1781.4 1781.6 1781.8
871 - 875 1782.0 1782.2 1782.4 1782.6 1782.8
876 - 880 1783.0 1783.2 1783.4 1783.6 1783.8
881 - 885 1784.0 1784.2 1784.4 1784.6 1784.8

PCS 1900 CHART 1 -- DOWNLINK (Base Station To Mobile)

NUMBERS (MHz)
512 - 515 1930.2 1930.4 1930.6 1930.8

516 - 520 1931.0 1931.2 1931.4 1931.6 1931.8
521 - 525 1932.0 1932.2 1932.4 1932.6 1932.8
526 - 530 1933.0 1933.2 1933.4 1933.6 1933.8
531 - 535 1934.0 1934.2 1934.4 1934.6 1934.8
536 - 540 1935.0 1935.2 1935.4 1935.6 1935.8
541 - 545 1936.0 1936.2 1936.4 1936.6 1936.8
546 - 550 1937.0 1937.2 1937.4 1937.6 1937.8
551 - 555 1938.0 1938.2 1938.4 1938.6 1938.8
556 - 560 1939.0 1939.2 1939.4 1939.6 1939.8
561 - 565 1940.0 1940.2 1940.4 1940.6 1940.8
566 - 570 1941.0 1941.2 1941.4 1941.6 1941.8
571 - 575 1942.0 1942.2 1942.4 1942.6 1942.8
576 - 580 1943.0 1943.2 1943.4 1943.6 1943.8
581 - 585 1944.0 1944.2 1944.4 1944.6 1944.8
586 - 590 1945.0 1945.2 1945.4 1945.6 1945.8
591 - 595 1946.0 1946.2 1946.4 1946.6 1946.8
596 - 600 1947.0 1947.2 1947.4 1947.6 1947.8
601 - 605 1948.0 1948.2 1948.4 1948.6 1948.8
606 - 610 1949.0 1949.2 1949.4 1949.6 1949.8
611 - 615 1950.0 1950.2 1950.4 1950.6 1950.8
616 - 620 1951.0 1951.2 1951.4 1951.6 1951.8
621 - 625 1952.0 1952.2 1952.4 1952.6 1952.8
626 - 630 1953.0 1953.2 1953.4 1953.6 1953.8
631 - 635 1954.0 1954.2 1954.4 1954.6 1954.8
636 - 640 1955.0 1955.2 1955.4 1955.6 1955.8
641 - 645 1956.0 1956.2 1956.4 1956.6 1956.8
646 - 650 1957.0 1957.2 1957.4 1957.6 1957.8
651 - 655 1958.0 1958.2 1958.4 1958.6 1958.8
656 - 660 1959.0 1959.2 1959.4 1959.6 1959.8
661 - 665 1960.0 1960.2 1960.4 1960.6 1960.8
666 - 670 1961.0 1961.2 1961.4 1961.6 1961.8
671 - 675 1962.0 1962.2 1962.4 1962.6 1962.8
676 - 680 1963.0 1963.2 1963.4 1963.6 1963.8
681 - 685 1964.0 1964.2 1964.4 1964.6 1964.8
686 - 690 1965.0 1965.2 1965.4 1965.6 1965.8
691 - 695 1966.0 1966.2 1966.4 1966.6 1966.8
696 - 700 1967.0 1967.2 1967.4 1967.6 1967.8
701 - 705 1968.0 1968.2 1968.4 1968.6 1968.8
706 - 710 1969.0 1969.2 1969.4 1969.6 1969.8
PCS 1900 CHART 2 -- DOWNLINK (Base Station To Mobile)(continued)

NUMBERS (MHz)
711 - 715 1970.0 1970.2 1970.4 1970.6 1970.8

716 - 720 1971.0 1971.2 1971.4 1971.6 1971.8
721 - 725 1972.0 1972.2 1972.4 1972.6 1972.8
726 - 730 1973.0 1973.2 1973.4 1973.6 1973.8
731 - 735 1974.0 1974.2 1974.4 1974.6 1974.8
736 - 740 1975.0 1975.2 1975.4 1975.6 1975.8
741 - 745 1976.0 1976.2 1976.4 1976.6 1976.8
746 - 750 1977.0 1977.2 1977.4 1977.6 1977.8
751 - 755 1978.0 1978.2 1978.4 1978.6 1978.8
756 - 760 1979.0 1979.2 1979.4 1979.6 1979.8
761 - 765 1980.0 1980.2 1980.4 1980.6 1980.8

766 - 770 1981.0 1981.2 1981.4 1981.6 1981.8
771 - 775 1982.0 1982.2 1982.4 1982.6 1982.8
776 - 780 1983.0 1983.2 1983.4 1983.6 1983.8
781 - 785 1984.0 1984.2 1984.4 1984.6 1984.8
786 - 790 1985.0 1985.2 1985.4 1985.6 1985.8
791 - 795 1986.0 1986.2 1986.4 1986.6 1986.8
796 - 800 1987.0 1987.2 1987.4 1987.6 1987.8
801 - 805 1988.0 1988.2 1988.4 1988.6 1988.8
806 - 810 1989.0 1989.2 1989.4 1989.6 1989.8

PCS 1900 CHART 3 -- UPLINK (Mobile to Base Station)

NUMBERS (MHz)
512 - 515 1850.2 1850.4 1850.6 1850.8

516 - 520 1851.0 1851.2 1851.4 1851.6 1851.8
521 - 525 1852.0 1852.2 1852.4 1852.6 1852.8
526 - 530 1853.0 1853.2 1853.4 1853.6 1853.8
531 - 535 1854.0 1854.2 1854.4 1854.6 1854.8
536 - 540 1855.0 1855.2 1855.4 1855.6 1855.8
541 - 545 1856.0 1856.2 1856.4 1856.6 1856.8
546 - 550 1857.0 1857.2 1857.4 1857.6 1857.8
551 - 555 1858.0 1858.2 1858.4 1858.6 1858.8
556 - 560 1859.0 1859.2 1859.4 1859.6 1859.8
561 - 565 1860.0 1860.2 1860.4 1860.6 1860.8
566 - 570 1861.0 1861.2 1861.4 1861.6 1861.8
571 - 575 1862.0 1862.2 1862.4 1862.6 1862.8
576 - 580 1863.0 1863.2 1863.4 1863.6 1863.8
581 - 585 1864.0 1864.2 1864.4 1864.6 1864.8
586 - 590 1865.0 1865.2 1865.4 1865.6 1865.8
591 - 595 1866.0 1866.2 1866.4 1866.6 1866.8
596 - 600 1867.0 1867.2 1867.4 1867.6 1867.8
601 - 605 1868.0 1868.2 1868.4 1868.6 1868.8
606 - 610 1869.0 1869.2 1869.4 1869.6 1869.8
611 - 615 1870.0 1870.2 1870.4 1870.6 1870.8
616 - 620 1871.0 1871.2 1871.4 1871.6 1871.8
621 - 625 1872.0 1872.2 1872.4 1872.6 1872.8
626 - 630 1873.0 1873.2 1873.4 1873.6 1873.8
631 - 635 1874.0 1874.2 1874.4 1874.6 1874.8
636 - 640 1875.0 1875.2 1875.4 1875.6 1875.8
641 - 645 1876.0 1876.2 1876.4 1876.6 1876.8
646 - 650 1877.0 1877.2 1877.4 1877.6 1877.8
651 - 655 1878.0 1878.2 1878.4 1878.6 1878.8
656 - 660 1879.0 1879.2 1879.4 1879.6 1879.8
661 - 665 1880.0 1880.2 1880.4 1880.6 1880.8
666 - 670 1881.0 1881.2 1881.4 1881.6 1881.8
671 - 675 1882.0 1882.2 1882.4 1882.6 1882.8
676 - 680 1883.0 1883.2 1883.4 1883.6 1883.8
681 - 685 1884.0 1884.2 1884.4 1884.6 1884.8
686 - 690 1885.0 1885.2 1885.4 1885.6 1885.8
691 - 695 1886.0 1886.2 1886.4 1886.6 1886.8
696 - 700 1887.0 1887.2 1887.4 1887.6 1887.8
701 - 705 1888.0 1888.2 1888.4 1888.6 1888.8
706 - 710 1889.0 1889.2 1889.4 1889.6 1889.8

PCS 1900 CHART 4 -- UPLINK (Mobile to Base Station)(Continued)

NUMBERS (MHz)
711 - 715 1890.0 1890.2 1890.4 1890.6 1890.8

716 - 720 1891.0 1891.2 1891.4 1891.6 1891.8
721 - 725 1892.0 1892.2 1892.4 1892.6 1892.8
726 - 730 1893.0 1893.2 1893.4 1893.6 1893.8
731 - 735 1894.0 1894.2 1894.4 1894.6 1894.8
736 - 740 1895.0 1895.2 1895.4 1895.6 1895.8
741 - 745 1896.0 1896.2 1896.4 1896.6 1896.8
746 - 750 1897.0 1897.2 1897.4 1897.6 1897.8
751 - 755 1898.0 1898.2 1898.4 1898.6 1898.8
756 - 760 1899.0 1899.2 1899.4 1899.6 1899.8
761 - 765 1900.0 1900.2 1900.4 1900.6 1900.8
766 - 770 1901.0 1901.2 1901.4 1901.6 1901.8
771 - 775 1902.0 1902.2 1902.4 1902.6 1902.8
776 - 780 1903.0 1903.2 1903.4 1903.6 1903.8
781 - 785 1904.0 1904.2 1904.4 1904.6 1904.8
786 - 790 1905.0 1905.2 1905.4 1905.6 1905.8
791 - 795 1906.0 1906.2 1906.4 1906.6 1906.8
796 - 800 1907.0 1907.2 1907.4 1907.6 1907.8
801 - 805 1908.0 1908.2 1908.4 1908.6 1908.8
806 - 810 1909.0 1909.2 1909.4 1909.6 1909.8

MS/BTS POWER CHARTS
MOBILE POWER CLASSES
GSM 900 DCS 1800 PCS 1900

dBm
POWER MAXIMUM PEAK MAXIMUM dBm MAXIMUM dBm
CLASS POWER PEAK PEAK
POWER POWER
1 20 W +43 1W +30 1W +30

2 8W +39 0.25 W +24 0.25 W +24
3 5W +37 --- --- 2W +33
4 2W +33 --- --- --- ---
5 0.8 W +29 --- --- --- ---
MOBILE POWER CONTROL LEVELS
GSM 900 DCS 1800 PCS 1900

POWER PEAK POWER PEAK POWER PEAK POWER
CONTROL dBm dBm dBm
LEVEL
0 +43 +30 +30
1 +41 +28 +28
2 +39 +26 +26
3 +37 +24 +24
4 +35 +22 +22
5 +33 +20 +20
6 +31 +18 +18
7 +29 +16 +16
8 +27 +14 +14
9 +25 +12 +12
10 +23 +10 +10
11 +21 +8 +8
12 +19 +6 +6
13 +17 +4 +4
14 +15 +2 +2
15 +13 0 0
16 reserved
17 reserved
18 reserved
19 reserved
20 reserved
21 reserved
22 to 29 reserved
30 +33
31 +32
BTS POWER CLASSES

BTS MAXIMUM PEAK dBm
POWER POWER
CLASS
GSM
1 320 -640 W +55 - 58
2 160 - 320 W +52 - 55
3 80 - 160 W +49 - 52
4 40 - 80 W +46 - 49
5 20 - 40 W +43 - 46
6 10 - 20 W +40 - 43
7 5 - 10 W +37 - 40
8 2.5 - 5 W +34 - 37
Micro BTS
GSM
M1 ?? - 0.25 W +19 - 24
M2 0.025 - ?? W +14 - 19
M3 ?? - 0.025 W +9 - 14

POWER POWER
CLASS
DCS 1800
1 20 -40 W +43 - 46
2 10 - 20 W +40 - 43
3 5 - 10 W +37 - 40
4 2.5 - 5 W +34 - 37
Micro BTS
DCS 1800
M1 0.5 - 1.6 W +27 - 32
M2 0.16 - 0.5 W +22 - 27
M3 0.05 - 0.16 W +17 - 22

POWER POWER
CLASS
PCS 1900
1 20 -40 W +43 - 46
2 10 - 20 W +40 - 43
3 5 - 10 W +37 - 40
4 2.5 - 5 W +34 - 37
Micro BTS
PCS 1900
M1 0.5 - 1.6 W +27 - 32
M2 0.16 - 0.5 W +22 - 27
M3 0.05 - 0.16 W +17 - 22
Reference Sensitivity Levels

MS Reference sensititvity dBm
GSM mobile class 1, 2, 3 -104
GSM handportable class 4 & 5 -102
DCS 1800 class 1 & 2 -100
DCS 1800 class 3 -102
PCS 1900 all classes -102
BTS Reference sensititvity dBm

GSM standard BTS -104
GSM Mini 1 -97
GSM Mini 2 -92
GSM Mini 3 -87
DCS 1800 standard BTS -104
DCS 1800 Mini 1 -102
DCS 1800 Mini 2 -97
DCS 1800 Mini 3 -92
PCS 1900 standard BTS -104
PCS 1900 Mini 1 -102
PCS 1900 Mini 2 -97
PCS 1900 Mini 3 -92

CONVERSION FACTORS
To convert between dBV (emf), dBV/m and dBm, use the following formulae:
dBV(emf) = dBm + 113.0

dBV/m = dBm + 136.5
Note: This assumes 0 dBi antenna gain and a frequency of 925 MHz
Ref. GSM Rec. 05.05 Section 5.
Some useful values are given below:
dBm V
dB V/m
dB
(emf)
-110.0 3.0 26.5

-104.0 9.0 32.5
-102.0 11.0 34.5
-101.0 12.0 35.5
-99.0 14.0 37.5
-93.0 20.0 43.5
-85.0 28.0 51.5
-64.5 48.5 72.0
-48.0 65.0 88.5
-43.0 70.0 93.5

Rx_LEV Values
The reported Rx_LEV values for received signal level are as follows:
Rx_LEV Received Signal Level Rx_LEV Received Signal

Level
0 Less than -110 dBm 40 -71 dBm to -70 dBm

1 -110 dBm to -109 dBm 41 -70 dBm to -69 dBm


23 -88 dBm to -87 dBm 63 greater than-48 dBm
24 -87 dBm to -86 dBm
25 -86 dBm to -85 dBm
26 -85 dBm to -84 dBm
27 -84 dBm to -83 dBm
28 -83 dBm to -82 dBm
29 -82 dBm to -81 dBm
30 -81 dBm to -80 dBm

31 -80 dBm to -79 dBm
32 -79 dBm to -78 dBm
33 -78 dBm to -77 dBm
34 -77 dBm to -76 dBm
35 -76 dBm to -75 dBm
36 -75 dBm to -74 dBm
37 -74 dBm to -73 dBm
38 -73 dBm to -72 dBm
39 -72 dBm to -71 dBm

Rx_QUAL Values
The reported Rx_QUAL values for received signal level are as follows:
Rx_QUAL Bit Error Rate Mean Value

Value Range
0 < 0.2 % 0.14 %

1 0.2 - 0.4 % 0. 28 %
2 0.4 - 0.8 % 0.57 %
3 0.8 - 1.6 % 1.13 %
4 1.6 - 3.2 % 2.26 %
5 3.2 - 6.4 % 4.53 %
6 6.4 - 12 8 % 9.05 %
7 > 12.8 % 18.10 %

GSM Training Manual PDF

Uploaded by

Copyright:

Available Formats

GSM Training Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GSM Training Manual PDF

Uploaded by

Copyright:

Available Formats

GSM Training Notes Racal Instruments Group

Introduction to cellular radio

Traditional mobile radio

Cellular network planning

Cellular radio - why does it work?

Cellular design objectives

Introduction to cellular radio - Page 1

1901 1st transatlantic radio transmission

The Radio Story So Far

Radio communication started at the beginning of the 20th Century,

Introduction to cellular radio - Page 2

Coverage area Guard band

Before Cellular Radio

Before cellular radio, personal communication over large areas relied

Introduction to cellular radio - Page 3

The cellular radio concept relies on many transmitters (or base

Note that a maximum cell radius of about 35 km is possible for GSM:

Introduction to cellular radio - Page 4

Almost all the theoretical explanations of cellular radio show cells as

Introduction to cellular radio - Page 5

Seamless coverage without high power transmitters

Cellular Radio - Why Does it Work?

Emitted RF power limits the range of a standard mobile radio. In an

Introduction to cellular radio - Page 6

Good speech quality

Cellular Design Objectives

Introduction to cellular radio - Page 7

Introduction to cellular radio - Page 8

GSM & its derivatives

GSM - not just voice

Introduction to GSM - Page 1

Introduction to GSM - Page 2

1982 Groupe Speciale Mobile formed

Introduction to GSM - Page 3

MS - BTS (uplink) BTS - MS (downlink)

Introduction to GSM - Page 4

1710.2 1784.8MHz 1805.2 1879.8MHz

1850 1910MHz 1930 1990MHz

GSM & Its Derivatives

GSM had been so successful in some developed countries that more

Introduction to GSM - Page 5

GSM - not just voice

As well as traditional speech communication a number of other

Introduction to GSM - Page 7

IMSI, PIN & PUK

(Note:-Test SIMs are used to provide special functions during phone

Introduction to GSM - Page 8

A typical GSM network

How GSM works: a mobiles perspective - Page 1

BTS BTS MSC

A Typical GSM Network

To understand how GSM works, consider what a normal GSM

How GSM works: a mobiles perspective - Page 2

How GSM works: a mobiles perspective - Page 3

Registration / location update

When a radio is switched on it needs to let the network know where it

(Note: different networks use different strategies for locating mobiles.

How GSM works: a mobiles perspective - Page 4

IMSI - International Mobile Subscriber Identity