Scribd
Upload
712 views2 pages

6 Steering Angle Sensor

This document provides instructions for replacing the steering angle sensor, which is part of the vehicle dynamics control system. The procedure involves 16 steps: 1) setting the steering wheel straight, 2) disconnecting the battery, 3) removing the airbag, 4) removing the steering wheel, 5) removing covers, 6) disconnecting the sensor connector, 7) removing screws securing the roll connector, 8) removing the sensor, 9) installing the new sensor and applying grease, 10) connecting everything back together in reverse order, and 11) performing adjustments to calibrate the vehicle dynamics control system after replacement. Proper precautions are described to avoid injury and ensure correct system operation after replacement.

Uploaded by

murdertrk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
712 views2 pages

6 Steering Angle Sensor

This document provides instructions for replacing the steering angle sensor, which is part of the vehicle dynamics control system. The procedure involves 16 steps: 1) setting the steering wheel straight, 2) disconnecting the battery, 3) removing the airbag, 4) removing the steering wheel, 5) removing covers, 6) disconnecting the sensor connector, 7) removing screws securing the roll connector, 8) removing the sensor, 9) installing the new sensor and applying grease, 10) connecting everything back together in reverse order, and 11) performing adjustments to calibrate the vehicle dynamics control system after replacement. Proper precautions are described to avoid injury and ensure correct system operation after replacement.

Uploaded by

murdertrk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

asieps_tobira.

book 17

Steering Angle Sensor


VEHICLE DYNAMICS CONTROL (VDC)

6. Steering Angle Sensor 9) Remove the steering angle sensor from roll con-
nector.
A: REPLACEMENT
CAUTION:
Do not perform the removal except when the
replacement.
When replacing three times or more, replace
the combination switch as assembly to protect
the threads.
1) Set the steering wheel in a straight-ahead posi-
tion.
2) Disconnect the ground cable from the battery. VDC00208
3) Remove the airbag module. 10) Turn the protrusion portion of new steering an-
<Ref. to AB-15, REMOVAL, Drivers Airbag Mod- gle sensor to match the alignment mark of inspec-
ule.> tion hole.
WARNING:
Always refer to Airbag System when perform-
ing the airbag module repair service.
(1)
<Ref. to AB-4, CAUTION, General Description.>
4) Remove the steering wheel. (2)
<Ref. to PS-14, REMOVAL, Steering Wheel.> (3)
5) Remove the screws and remove the steering
column lower cover.
6) Remove the two screws securing the steering
column upper cover. VDC00209
7) Unlock the harness band and disconnect the
connector of the steering angle sensor. (1) Protrusion portion
(2) Inspection hole
(3) Alignment mark

CAUTION:
Be careful not to allow foreign matter to enter
(1) into inspection hole.
11) Align the center of roll connector.
<Ref. to AB-24, INSTALLATION, Roll Connector.>
(2) 12) Apply a thin coat of grease that is supplied with
VDC00093
the new part, to the 4 protruding sections of the
steering angle sensor.
(1) Harness band
(2) Connector

8) Remove the screws which secure the roll con-


nector to steering column.

(1)

ABS00435

(1) Apply grease.

VDC00207

VDC-17
asieps_tobira.book 18

Steering Angle Sensor


VEHICLE DYNAMICS CONTROL (VDC)

13) Align the position of the protrusion and install


roll connector to steering angle sensor.
Tightening torque:
0.5 Nm (0.05 kgf-m, 0.36 ft-lb)

VDC00208

14) Install the roll connector to combination switch.

VDC00207

15) Install the steering wheel.


<Ref. to PS-14, INSTALLATION, Steering Wheel.>
Tightening torque:
44 Nm (4.5 kgf-m, 32.5 ft-lb)
16) Install the airbag module to the steering wheel.
<Ref. to AB-15, INSTALLATION, Drivers Airbag
Module.>
WARNING:
Always refer to Airbag System before per-
forming the service operation.
<Ref. to AB-4, CAUTION, General Description.>
17) Connect the ground cable to the battery.
CAUTION:
After completion of installation, adjust the fol-
lowing two positions.
Positioning to the center of steering angle
sensor
Positioning the yaw rate & lateral G sensors
to zero.
The above procedure is required for the VDC-
CM to identify vehicle position afterward. For
the setting procedures of the 2 steps above, re-
fer to VDC Control Module and Hydraulic Con-
trol Unit (VDCCM&H/U). <Ref. to VDC-11,
ADJUSTMENT, VDC Control Module and Hy-
draulic Control Unit (VDCCM&H/U).>

VDC-18

You might also like