Scribd
Upload
63 views1 page

A B C D: 80.71 Multifunction and Multi-Voltage Solid-State Output Timer (SST)

This document describes an 80.71 multifunction and multi-voltage solid-state output timer. The timer can operate on voltages between 19-265V AC/DC, has 1 NO contact rated for 1A, and operates in temperatures from -20 to 50 degrees Celsius. It has rotary dials to select time scales and functions, and can be used for on-delay, off-delay, interval, and symmetrical flasher applications. Wiring diagrams show options for starting the timer via the supply line or an external contact.

Uploaded by

Hung Cuong Pham
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
63 views1 page

A B C D: 80.71 Multifunction and Multi-Voltage Solid-State Output Timer (SST)

This document describes an 80.71 multifunction and multi-voltage solid-state output timer. The timer can operate on voltages between 19-265V AC/DC, has 1 NO contact rated for 1A, and operates in temperatures from -20 to 50 degrees Celsius. It has rotary dials to select time scales and functions, and can be used for on-delay, off-delay, interval, and symmetrical flasher applications. Wiring diagrams show options for starting the timer via the supply line or an external contact.

Uploaded by

Hung Cuong Pham
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

80.71.0.240.

0000 1 2
ENGLISH
(24...240) V AC (50/60 Hz) / DC 80.71
Umin 19 V AC / DC MULTIFUNCTION AND MULTI-VOLTAGE SOLID-STATE
Umax 265 V AC / DC OUTPUT TIMER (SST)
A
1 NO (SPST NO) B 1 FRONT VIEW
1 A (19...265) V AC / DC C A Time scales rotary selector
B Time setting
AC15 1A C LED
DC1 1A D D Functions rotary selector
88.8 mm
(20...+50)C 60.8 mm 2 TIME SCALES

IP20
17.5 mm 3 WIRING DIAGRAM AND FUNCTIONS
(WARNING: the functions must be set before energising the timer)
3a Without signal START functions
Start via contact in supply line (A1)
AI On-delay
80.71 LED UN 15 - 18 3 3a 3c DI Interval PI PE
SW Symmetrical flasher (starting pulse on)
3b External START functions
Start via contact into control terminal (B1)
BE Off-delay with control signal
PI PE CE On- and off-delay with control signal
DE Interval with control signal on
3c Possible to control an external load, such as another relay coil
or timer, connected to the signal start terminal B1.
3d With DC supply, positive polarity has to be connected to B1
PI PE terminal (according to EN 60204-1).
3e A voltage other than the supply voltage can be applied to the
command Start (B1), example:
A1-A2 = 230 V AC
3d B1-A2 = 24 V DC
3b PI
OTHER DATAPE
Minimum control impulse: 50ms
Recovery time: 50 ms
35 mm rail mount (EN 60715)

WORKING CONDITIONS
PI In conformity
PE with the European Directive on EMC (89/336/EEC), the
timer relay has a level of immunity, against radiated and conducted
disturbances, considerably higher than requirements of EN 61812-1
standard. However, devices like transformers, motors, contactors,
3e switches and power cables may cause disturbances and even damage
the timer electronic circuit. For that reason, the wiring cables must be
as short as possible, and, when necessary, the timer shall be protected
PI PE
by the relevant RC network, varistor or surge voltage protector.

Utility Model - IB8071001 - 10/16 - FINDER S.p.A. - 10040 ALMESE (TO) - ITALY

You might also like