Induction Motor Speed Control

Inverter Module (IMSCIM-V1)

Features:

Support Motor Type 3-phase Induction Motor, 220V, 50/60Hz, up to 2.2 KW (3 horsepower)
Control method Scalar (V/F) Control
Power +310V DC, up to 15A for motor drive and
+15V DC, up to 0.15A for control circuit
Motor Current Up to 15A
Main Controller MC3PHAC (Freescale Semiconductor)
IGBT module FSBF15CH60BT (Fairchild Semiconductor)
Protection / Fault Over-voltage, Under-voltage, Over-heating, Over-current
Fault recovery delay 3 sec
PWM frequency 5/10/15/20 kHz (10 kHz default / recommended)
Size 43 x 75 x 95 mm
Weight 110 gram

Safety instructions
Warning: During assembly and operation, the Induction Motor Speed Control Power Module
board poses several inherent hazards, including bare wires, moving or rotating parts
and hot surfaces. Serious personal injury and damage to property may occur if the kit
or its components are used or installed incorrectly.
 Introduction

Open-frame, single-board Induction Motor Speed Control Inverter Module (IMSCIM-V1)

provides easy to install complete solution for 220 V Tree Phase AC motor Speed Control. The Inverter
Module need two voltage source with common ground: +310 V DC and +15 V DC for control circuit.
Inverter Module PCB and main components description represents at Fig. 1.
PWM frequency
setting jumper Motor Voltage
Test points JP2, JP3, JP4 boost setting
Trimmer RV2
Power LED1: +5V
Circuit sensor Power LED2:+15V
50/60 Hz motor
setting jumper JP1

Over-voltage
MC3PHAC
Fault LED

Jumper JP5:
Select
Under-voltage,
Serial or
Over-heating,
HW control
Over-current
Fault LED Serial
communication
connector CN4

Motor and
Power
Terminal
External control
Block CN1 connector CN3

Brake-ON LED3 Internal/External

control jumper
JP6, JP7
Brake circuit

+15V connector CN2

Forward/Reverse Button S2
Speed Setting Acceleration Setting
Start/Stop Button S1 Variableresistor RV1 Trimmer RV3

Fig. 1.IMSCIM-V1
 Motor and Power Wiring
Warning: All connectors have no isolation

General motor and power supply connection represents at Fig.2.

+310 V DC

Motor U
V
W

GND
Rectifier / Power
Factor Corrector

Transformer / Rectifier / Regulator Brake resistor +

GND 470..1000uF, 25 V

+15V DC

Transformer / Rectifier / Regulator

Isolated +15V5% Power Supply

Fig. 2. Motor and Power Supply Wiring

Power Supply +15 V

Power supply +15 Volts must be isolated and must provide stable voltage in range +13.5 to 16.5
volts, output current 150 mA or more. If voltage is less than 12 volts Alarm will happen (refer Table 3). If
voltage is over 20 volts IGBT module might be damaged.It is recommend to connect additional
aluminum electrolytic capacitor 470..1000uF, 25V close to connector CN2 to avoid voltage reducing
during motor start.

Power supply +310V

Various type of Power supply +310 V can be used. It can be simple rectifier and corresponded
capacitor or Power Factor Corrector. Inverter Module has protection: Over-voltage Fault if voltage over
407V DC and Under-voltage Fault if voltage under 175V DC (Refer Table 1).
If voltage going over 390V due to back-EMF generation during motor bracing(Refer Table 1)
brace circuit (refer Fig. 1) is turning on and power will discharge to eternal Brake resistor (refer Fig. 2).

Table 1.
Voltage Description
over 407 V Over-voltage Fault:
390V Brake On Voltage:
+280V to +350V Recommended range is
under175 V Under-voltage Fault
 Motor Adjustment
Default settings allow running any 220V induction motor without any damage of equipment or motor
and can be acceptable for most types of motors. However, adjustment parameters can increase
performance of system itself. Below are default settings (Table 2) and several adjustment steps
described.

Table 2.
Default settings Description
Jumper JP1 at 1-2 position Position 1-2 suitable for 50 Hz motors. If motor 60 Hz used with
Inverter Module change JP1 to 2-3 position
Jumper JP2, JP3, JP4 at PWM frequency influence to motor noise and power losses. At high
10kHz position frequency PWM motor not make any sound, but motor and Inverter
Module power losses increased. At low PWM frequency motor can
make noise. It is recommended to use default PWM frequency 10kHz.
Jumper JP5 is open Jumper JP5 is open for HW control (control speed by Variableresistor
RV1, Acceleration by Trimmer RV3, Start/Stop and Forward/Reverse
by Button S1 and S2)
Jumper JP5 is closed for control via serial communication connector
CN4. If Jumper JP5 is closed, setting for RV1, RV3, S1, S2, JP1, JP2, JP3,
JP4, JP6, JP7 are ignored.
Jumper JP6 and JP7 at 2-3 Jumper JP6 at 2-3 position for speed control by internal
position Variableresistor RV1
Jumper JP6 at 1-2 position for speed control by external
Variableresistor, connected to CN3 (refer "External Control" below)
Jumper JP7 at 2-3 position for acceleration control by internal
Trimmer RV3
Jumper JP7 at 1-2 position for acceleration control by external
Variableresistor, connected to CN3 (refer "External Control" below)
Note: settings for Jumper JP6 and JP7 are ignored if Jumper JP5 is
closed.
Trimmer RV2 (Motor Trimmer RV2 set Motor Voltage Boost in range 0 to 24%. Motor
Voltage Boost) turn left (0%) Voltage Boost has to be increase for increase motor torque at low
speed.
Note: New value is applies after controller reboot.
Trimmer RV3 (Motor Trimmer RV3 set a motor acceleration/deceleration during motor
asseveration) turn middle start, stop and any motor speed thanes.
point (middle asseveration)
Variable resistor RV1 (Motor Variable resistor RV1: motor speed control
Speed) turn middle point

Adjustment steps:
1. To change motor rotation direction, just reversing the connectionof any two motor wires.
2. Set 50/60 Hz motor setting jumper (JP1)
3. Set PWM frequency setting jumper (JP2, JP3, JP4) at 5, 10, 15 or 20 kHz. LowPWM frequency makes
motor noise; High PWM frequency makes more IGBT module power losses and high temperature. PWM
frequency 10kHz is recommended (default setting).
4. Set Motor Voltage boost setting Trimmer (RV2) in percent in range from 0 to 20%. (0% - left position is
default setting)
 External Control
It is possible to use external (remote) motor control using external variable resistors and buttons,
connected to External control connector CN3. If external "Start/Stop" and "Forward/Reverse"button are
used, internal buttons S1 and S2 must be at release(non-pushed) status.
Warning: All components and wires, connected to CN3 must be isolated, no any signal isolation
on Inverter Module
Circuit diagram for external buttons and variable resistors connection via CN3 represents at Fig.3.
Must be isolated!

Forward / Reverse
Acceleration
+5V
10kOhm
Speed
10kOhm
GND

Start / Stop

Fig. 3. CN3 Wiring

To use external variable resistors for speed and acceleration control set jumpers JP6 and JP7 at
1-2 position (refer Table 2).It is possible to use just one external variable resistor, for example Speed
control only, in this case JP6 have to be set at 1-2 position and JP7 have to be set at 2-3 position. Same
for buttons, it is possible to use just one external button, for example "Start/Stop", in this case
"Start/Stop" button in the board must be at release(non-pushed) status.

Serial Communication
It is possible to use alternate motor control method via serial communication. To activate serial
communication control jumper JP5 must be closed.

High voltage Isolator

GND
Personal Computer
RX TX
Controller
TX RX

+5V GND Other devices

Fig. 4. CN4 Wiring

For data protocol description refer to MC3PHAC manual and application notes at
http://www.freescale.com/
 Alarm
List of Alarm and fault reason represents at Table 3.
Table 3.
Alarm Description LED
Over-voltage Power supply +310V more than +407 Volts LED 4, LED 5
Under-voltage Power supply +15V less than +12 Volts LED 5
Power supply +310V less than +175 Volts
Over-current Motor current more than 17 A LED 5
Over-heating IGBT module over-heating LED 5

Fault recovery delay is 3 second.

Mounting
PCB size: x=75, y=95 mm, PCB thickness: 1.6 mm
PCB / front panel hole location (Origin: left, bottom PCB corner)

Table 4.PCB Mounting holeposition (in mm):

Position X Position Y Drilling diameter
1 5.0 5.0 3.2
2 70.0 5.0 3.2
3 70.0 90.0 3.2
4 5.0 90.0 3.2

Table 5.HeatsinkMounting holeposition (in mm):

Position X Position Y Drilling diameter [mm]
1 32.2 70.0 3.2
2 32.2 30.0 3.2

Table 6.Button holeposition (in mm)

Position X Position Y Drilling diameter Remark
1 45.0 15.0 6.2 Forward / Reverse
2 45.0 5.0 6.2 Start / Stop

Table 7.Variable resistor / Trimmerhole position (in mm)

Position X Position Y Drilling diameter Remark
1 55.0 10.0 4.0 Speed
2 65.0 13.0 4.0 Acceleration
3 58.0 91.0 4.0 Boost
 75

95

5
5
45
Origin 55
70

Fig. 5. Top view dimension

PCB to Front Panel spacer: 15 mm

PCB to Heatsinkspacer: 10 mm

15 mm spacer

10 mm spacer

Fig. 6. Side view dimension

 70

30

32.2

Origin
Fig. 7. Bottom view dimension

Additional information about Heatsink size and mounting refer to FSBF15CH60BT manual and
application notes at http://www.fairchildsemi.com/

Errata
PCB holes wrong position
Description: PCB holes for FSBF15CH60BT mounting screw are shifted 2.8 mm (refer fig. 8)

2.8 mm

fig. 8. PCB hole wrong position

Workaround:None
Fixed: will fix in next revision