Repowering Your Sailboat
Repowering Your Sailboat
Repowering Your Sailboat
WindCheck Magazine
January, 2011
http://windcheckmagazine.com
RepoweringYourSailboat
by, Joe DeMers
Customers ask if rebuilding their present engine is financially feasible. It is usually not so. Parts can be
expensive and difficult to find, if theyre even available. Rebuilding an engine without rebuilding the
transmission is a bad idea, as the transmission becomes the weak link in the powertrain.
Old raw water [salt water] cooled engines, such as the Volvo Penta MD7, MD11, Farymann A30M and
Atomic 4 gasoline engine, are very poor candidates for rebuilding. They usually break during
disassembly, due to advanced internal corrosion, and cannot be reassembled. Also, the internal water
passages in the block and head are wasted away to a fraction of their original thickness, with a major
and permanent engine failure inevitable. Most machine shops that rebuild engines will not touch salt-
water cooled engines for these reasons.
Theres also a world of difference between a professionally rebuilt engine and a home rebuilt engine. It
takes a high degree of precision, experience, technical skill, and the correct machine and hand tools to
correctly rebuild an engine. This means you must, at a minimum, hire a professional to rebuild the entire
fuel injection system, engine head, and correctly inspect, fit, and install the other major components.
This costs money that is better spent on a new technology diesel.
Considering these factors, most customers choose a new engine for their boat, which actually is the
correct financial decision.
The first question a customer usually asks is, How do I select the new engine for my boat? We always
answer with the following questions
Answers to the above questions determine the engine we recommend. For example, if you sail on an
inland lake with no tidal currents, you dont need a lot of horsepower to drive the boat. Conversely, if
you sail offshore, where you encounter large waves, strong winds, and also need electrical generating
capacity to operate radar, an autopilot, watermaker, etc., we suggest more horsepower, along with a
larger alternator or two.
The trend for the last 15 years is to install more powerful engines in sailboats. Some customers want a
powerboat when not sailing, and desire a large engine to drive the boat to hull speed, and to maintain
speed when encountering wind and wave. In a displacement hull sailboat, this attempt is easily
overdone.
Remember, the speed of a displacement hull (one that plows through the water, in contrast to one that
skims over the water] is limited by the length of her waterline. Once top speed [hull speed] is attained,
the boat cannot go faster, no matter how much horsepower is installed. This is because the hull has
formed a bow wave, a stern wave, and a trough between them. The boat is sitting in a hole, and cannot
climb her own bow wave.
Therefore, it will take X amount of horsepower to drive a sailboat with a Y waterline length to hull
speed. We then suggest a bit more horsepower, for reserve power when fighting strong currents and
waves. More power than this is not needed or desired, as the boat cannot go faster than hull speed.
Why pay for horsepower that cannot be used to drive the boat?
One BIG limiting factor in pushing any sailboat is the diameter of the propeller. If your boat can only fit a
12 diameter prop, such as the Tartan 34C, more than 25 horsepower is a waste of money. This is due
to the inability of the small prop to transfer greater horsepower to the water. Also, an oversized engine
2
costs more, weighs more, and is harder to service since it fills the engine space more completely than a
correctly sized engine.
Lets discuss the Catalina 30, an extremely successful design of 6000+ hulls built. Hull speed of this
boat, with her 25-foot waterline, is a theoretical 6.5 knots. The boat needs only 12 horsepower to reach
hull speed, under ideal conditions [clean bottom, flat water, no wind, correct transmission reduction
ratio, and correct prop]. Now, lets add a bit more horsepower to ensure the boat can reach hull speed
under less than ideal weather conditions. Sixteen horsepower is adequate. Twenty horsepower is ideal
for this boat, as boat speed is maintained under most conditions, while also charging batteries.
Remember, the boat is still an auxiliary powered sailboat, not a powerboat. If you must make headway
under power into 25+ knots of wind, and the resulting waves, you need a powerboatand a seatbelt!
Repowering your vessel is your chance to install the correct engine for your exact application. To
maximize powering efficiency, the engine, transmission reduction ratio, and propeller must work
together. Dont assume that your present transmission ratio and prop are making the most of your
engines horsepower. Many times when customers complain about poor boat performance, its because
the propellers diameter, pitch, or transmission reduction ratio do not compliment the engines power.
Your engine should be running at cruising rpm when the boat is at hull speed. Cruising rpm is usually
somewhere between 85% to 95% of maximum engine rpm. This will allow the engine to develop its
rated horsepower and operate the cooling system efficiently, and will correctly load the engine for
maximum service life. There will also be a few hundred rpm in reserve, to maintain hull speed when
encountering wind and wave.
If you intend to install an engine of X horsepower because thats what the boatbuilder did, you may be
perpetuating a mistake. Thats because it is very common in the boatbuilding industry to install an
engine that was purchased inexpensively, regardless of its overall suitability for the application. One
example is the Cape Dory 28, displacing 9,000 pounds. The factory sometimes installed a VolvoMD2B
engine of 25 horsepower, weighing 505 pounds, which is WAY too much power and weight for the
application. The boat simply cannot use all the available horsepower, and the boat is handicapped by
the extra engine weight. A much more suitable engine would be one of 13 horsepower, as it has plenty
of power to drive her to hull speed, such as the old VolvoMD7A. TheMD7A was installed in the heavier
Cape Dory 30, and is smaller and lighter than the MD2B by 120 pounds.Modern designs such as the
BetaMarine 13.5 horsepower engine weigh 195 pounds, resulting in improved sailing performance,
particularly in light air.
Installation Considerations
Any new engine must be installed to the latest marine standards. This means only certified marine-
grade materials be used for the exhaust, cooling, ventilation, electrical, control and fuel systems. These
specialized parts and materials are not available at Home Depot. The American Boat and Yacht Council
(ABYC; abycinc.org) publishes voluntary engine installation standards for small craft.
The most common mistake boat owners make when repowering is to duplicate the old exhaust system
currently. This results in a new engine being installed to an outdated standard, and puts it at risk for
major damage. A wet marine exhaust system is a critical installation in any sailboat. It must be designed
and installed to prevent raw water from backflooding the engine, and also have minimal restrictions to
allow the engine to freely breathe.
Backflooding is very damaging to any engine.Major repairs are likely if salt water enters the cylinders.
3
This can occur when sailing (engine off ) in a following sea, or when the boat is pitching or heeling, thus
swamping the exhaust through hull.We prefer a through-hull with an integral flapper valve, as it provides
another layer of protection against backflooding.
The ABYC says the exhaust through-hull must be installed where it will not be underwater during the
normal operation of the boat. The ideal location is in the middle of the transom. If this is not practical,
the through hull-should be located as high and as close to centerline as possible. The old practice of
locating the exhaust through-hull on the counter is a bad idea, as it will be submerged whenever the
boat is underway.
Exhaust system hose must be certified for that specific use, and should be secured using T bolt type
hose clamps. These clamps are highly recommended for this critical application, and are far superior to
worm drive type clamps. We always use 3M 5200 adhesive sealant on exhaust hose connections, to
eliminate exhaust water weeping and any possible minor exhaust gas leaks. Ideally, there should be
soft wall (no internal wire) hose between the engine and muffler, for maximum flexibility. The
remaining hose is usually the wire reinforced and corrugated type, so it cannot kink when bent into a
tight radius.
A vent loop, or siphon break, is needed on any engine that is installed at or below the waterline. Its
4
function is to introduce air into the exhaust system, to break any siphon action that may occur when
sailing. We prefer the minimally restrictive type, with stainless steel tubing and a plastic valve. It should
be installed as close to centerline as possible, and at least two feet above the static waterline. We
usually install them under the bridge deck. The exhaust hose should run vertically from the muffler, to
the highest point in the exhaust system. We like to see the highest point well above the underside of the
cockpit sole. From there, it should run downhill to the through-hull.
If room allows, an additional loop of exhaust hose can be located just inside the transom. This will force
any backflooding water to work against gravity instead of easily entering the exhaust system.
Alternately, a one-piece plastic exhaust part, shaped like a compact saxophone, can be installed for this
function. If a marine check valve can be installed, it will assist in keeping that new engine from
drowning. Remember, all exhaust components must work together to help prevent engine backflooding.
A correctly designed wet exhaust system will have several of the aforementioned items to help prevent
this potential engine disaster.
The location of the fuel tank deck plate has caused many problems. Many old boats have the fill located
in the cockpit sole, which reminds us of a bathtub drain. Any water that enters the cockpit will attempt to
get past the fill, and enter the fuel tank. We strongly suggest relocating the deck plate to a winch island,
where standing water cannot accumulate over it. We prefer all stainless construction, as plastic can
warp in the sun. All deck plates rely upon a rubber O-ring to seal out water check yours for condition.
There must be a ground wire of at least 6- gauge copper, electrically connected between the metal deck
plate and the fuel tank, to remove any static electricity produced when refueling. Use only USCG
approved fuel hose for the tank fill and tank vent. A shut off valve at the tank is also required.
5
with a non-running engine at a critical time.
We suggest the standpipe be extended with nylon tubing, to lay along the bottom of the tank. Now, your
fuel filter will continually remove any contaminants, and maintain only clean fuel in your tank. A
refinement is to pre-filter all fuel BEFORE it enters your tank with a funnel designed for such use. Racor
makes several models that will remove all water and grit.
The fuel feed system should use US Coast Guard grade A1 marine fuel hose, which meets the highest
standards for chafe resistance, fuel permeation and fire resistance. Copper tubing is not allowed, as its
electrically conductive and subject to work hardening, impact damage and leaks.
A fuel filter/water separator must be installed, as diesel engines MUST HAVE very clean, water-free fuel
to operate. The Racor model 500 with clear sediment bowl is preferred. Its a simple, top loading design,
and filter elements are common and inexpensive. Also, it will trap and hold a cup of water, to protect
your engines expensive fuel injection system. A drain is provided so you can manually remove water
and junk BEFORE it can move along to the engine.
The Racor filter should be installed outside the engine space, where the fuel is not subject to engine
heat, which can result in a loss of engine performance. Leave room above the unit for easy element
removal and replacement.
Secure the fuel hoses to bulkheads with stainless clips that have rubber chafe protection. Marine-grade
stainless steel hose clamps with an additional band of metal under the screw slots (called lined clamps)
are ideal, so the hose is not damaged by the clamp.
The fuel return hose, from engine back to tank, should have a U orientation somewhere along its
length to ensure the fuel injectors are not siphoned dry while sailing. The bottom of the U must be
lower than the bottom of the tank. If overlooked, this important detail can result in an engine not starting
after sailing,
Cooling Systems
The raw water cooling system can contribute to engine overheating, if the following details are ignored:
A scoop strainer (mounted outside the hull) has no place on a sailboat, as they can force water
past the raw water pump while sailing, fill the wet muffler, then allow water to backflow and enter
the engine cylinders. They also will not allow bottom paint to be placed inside the through-hull, and
cannot be easily inspected for barnacles or other restrictions. Much better is a common mushroom
head bronze through-hull that is easily maintained and inspected, even with the boat in the water. A
certified marine seacock, preferably bronze, and of ball valve construction, should be installed to
ABYC standards.
A ball valve, commonly seen just screwed to a throughhull, is a very poor substitute. We remove
inferior or incorrect through-hull/valve installations, and insist the customer not compromise when
keeping the ocean out of the boat! BEWARE the cheap ball valve designed for shoreside
installations. If the boat should sink, the insurance company will rightly refuse the claim.
A bronze raw water strainer, with clear bowl, designed for use below the waterline, should be
installed inside the boat. The plastic type (designed for bait wells, fresh water systems, etc.) is not
suitable for this critical application. The strainer should be located where its easily observed and
6
maintained. The hose between the ocean and the engine must be of wire reinforced, below
waterline marine certified type, so it will not collapse under raw water pump suction and cause the
engine to overheat. We actually saw a boat where the owner had used common garden hose, and
he was dumbfounded when we immediately ripped it out.
Your engine can be plumbed to heat fresh water for cooking and showers. Heating this water is free
and it will be available whenever the engine has run for about one hour. This requires the installation of
a water heater tank with an internal heat exchanger. If the tank is located at the same level, or higher
than the engine, a remote header tank must be installed at the high point of the system. This will ensure
that the engines cooling system will not get airbound, and possibly overheat. An ideal location for the
remote header tank is just inside a cockpit locker, where it is easily observed and maintained. A
translucent plastic coolant recovery bottle is highly recommended, as it will assist in purging all air from
the cooling system and allow checking the coolant level at a glance.
Ancillary Systems
All diesel engines need lots of fresh air for combustion. Ideally, a blower, wired to the key switch and
designed to automatically run and shut off with the engine, should be installed to create a minor vacuum
inside the engine space.
The hot air suction hose should be located high and aft in the compartment, while the cool air intake
hose should be low and forward, to completely ventilate the engine space. Alternators produce heat
when operating, and the fresh, cool air provided by this system will contribute greatly to the service life
of all components subject to engine and alternator heat.
An excellent upgrade from a 2-lever engine/transmission control system is a single lever control. This
facilitates simple, intuitive engine operation, and ensures that the transmission can only be engaged
when the engine is running at idle speed. Thats important when approaching your slip a bit too fast!
The control panel should be mounted where it can be reached and observed without leaving the helm.
Otherwise, starting and stopping the engine and watching the gauges will be difficult and distracting.
The stuffing box (or packing box) causes many problems, mainly because it gets ignored. We like the
traditional bronze type, with Gore-Tex packing. If the packing nut is correctly adjusted on a smooth prop
shaft, and engine alignment is correct, it will not leak at any time. My personal Catalina 27 had a new
stuffing box and prop shaft installed in 2007. I have done nothing since the installation, and it does not
leak, period. We do not recommend the so-called dripless prop shaft seal. In our experience, they
solve a problem that does not exist and we refuse to install them because theyre unreliable. The
bronze type is cheaper, easier to adjust and maintain, fire and impact resistant, supports the prop shaft,
is simpler and MUCH more reliable. These characteristics are very desirable at sea!
The stuffing box hose (stern tube hose) should be replaced during a repower, for reliability. Use hose
intended for this application nothing else will do. Also install new T-bolt type clamps for this critical
installation.
The cutless bearing supports the shaft, and is located just forward of the prop. Inspect it for wear or
cracking of the rubber lining. If a new prop shaft is installed, a new cutless bearing is required.
Stainless prop shafts are now standard in the industry, as they are less expensive, stiffer, and harder
than bronze shafts. The overhang (length of prop shaft between the cutless bearing and the prop)
must be no greater than one shaft diameter, to avoid shaft whip and premature cutless bearing wear.
7
Your old prop shaft MAY be reusable, if it passes inspection. Most prop shops will check it for free. It
should be inspected for straightness (within .003 along its length), corrosion and wear. Shafts can be
straightened at prop shops, although it may be cheaper to buy a new shaft. Have the shop fit and face
the new coupler to the shaft, so these parts rotate concentrically, to minimize vibration.
We recommend 2-blade props for sailboats, unless you must regularly fight strong wind, waves, or
current. A 3-blade prop will provide more thrust under those conditions. The tradeoff is increased drag
under sail. An excellent compromise is a 2-blade prop with large blade area. It is less expensive than a
3-blade, but will provide most of the thrust, along with the reduced drag of a 2- blade.
Diameter and pitch are the main variables when specifying a prop. Again, the engine horsepower,
transmission reduction ratio, and prop must be correctly matched so they work in concert to efficiently
drive the boat. Correctly specifying and installing a new engine and related components will ensure the
utmost reliability, service life, and enjoyment of your vessel. For more information, visit
soundmarinediesel.com.
Joe DeMers has worked in the marine industry as a certified marine diesel mechanic for 30 years. He
started his business, Sound Marine Diesel LLC, in 1997, and sells and installs Beta Marine diesel engines
and generators.