Capanivo

Series CN 4000

Instruction manual

sc300684_685
010514

1
UWT GmbH
Westendstrae 5 Tel.: +49 (0)831 57123-0 Internet:www.uwt.de
D-87488 Betzigau Fax: +49 (0)831 76879 E-Mail: [email protected]

Scope of this Types CN 4020 / 4030 / 4050

instruction Approval CE / ATEX / IEC-Ex
manual:
Electronic modules Relay (SPDT, DPDT) PNP

2
Table of Contents

Safety /warning notes Page 4

Fields of application Page 4

Technical Data Page 5

Installation Page 15

Electrical connection Page 21

Settings Page 27

Switching logic Page 29

Maintenance Page 30

Spare parts Page 31

ATEX / IEC-Ex Notes Page 32

CE- Declaration of Conformity Page 35

3
Safety /warning notes

Installation, maintenance and commissioning may be accomplished only by

qualified technical personnel.
For terminal connection of the device, the local regulations or VDE 0100
(Regulations of German electrotechnical Engineers) must be observed.
All field wirings must have insulation suitable for at least 250V AC. The
temperature rating must be at least 90C (194F).
In the case of handling by untrained personnel or handling malpractice, the
safety of the device cannot be guaranteed.

Fields of application

Level limit switch for level limit detection in powder and bulk materials.

4
Technical Data

Plastics PA

Aluminium

5
CN 4020
120C

Material according
to order data

Accessory

min. -1bar (-14.5psi)

max. +16bar (+232psi)

~ 0,5kg (1.1 lbs)

6
 L=190mm L=400mm
CN 4020
180C

min. -1bar (-14.5psi)

max. +16bar (+232psi)

~ 1.8kg (4.0 lbs)

7
CN 4030

Material according to order data

min. -1bar (-14.5psi)

max. +16bar (+232psi)

~ 0.8 kg (1.8 lbs)+ L: 0.8 kg/m (1.8 lbs/39.9) (1)

~ 1.5 kg (3.3 lbs)+ L: 1.6 kg/m (3.5 lbs/39.9) (2)

(1) = Aluminium (2) = Stainless steel

8
CN 4050

Material according to order data

min. -1bar (-14.5psi)

max. +6bar (+87psi)

~ 0.9 kg (2.0 lbs)+ L: 0.25 kg/m (0.55 lbs/39.9) (1)

~ 1.4 kg (3.1 lbs)+ L: 0.25 kg/m (0.55 lbs/39.9) (2)

(1) = Aluminium (2) = Stainless steel

9
 C

CN 4020
120C

10
 C

CN 4020
180C

11
 C

CN 4030

12
 C

CN 4050

13
Bulk material

r 1.6

<30mm

r Dielectric constant

14
Assembly

CN 4020

(1)

(1) Protective angle (canopy) in case of high mechanical load

15
 CN 4020

(2)

(3)

(2) Mech. load of the sensor

(3) Observe minimum distances

(3)

16
 CN 4030

(4)

(4) Sliding sleeve: Tighten straining screws with 20Nm

17
 CN 4030
Mech. load of the sensor

Observe minimum distances

18
 CN 4050

(3)

(2)

(2) Mech. load of the sensor

(3) Observe minimum distances

19
Fixing Threads

(1)

20Nm
40Nm (2)
(1) Flat gasket (2) Metal

Alignment

Ingress protection IP 66

20
Treatment

Electrical connection

Terminals according to selected version

21
 Relay SPDT

0.14 - 2.5mm
(AWG 26-14)

25/26
max. max.
10A 5A

PE + - AC max. 250V, 3A (3)

DC max. 30V, 5A (3)

(1)
21...27V DC 10% (2), max. 1.5W

(4) 2225Vrms

(1) Power supply

(2) Including 10% from EN 61010
(3) Non inductive
(4) Isolating voltage

22
 Relay DPDT

0.14 - 2.5mm
(AWG 26-14)

25/26
max. max. max.
10A 10A 10A

PE + -
L N AC max. 250V, 8A (3)
DC max. 30V, 5A (3)
(1)
21...230V 50-60Hz 10% (2) , max. 18VA
21...45V DC 10% (2) , max. 2W

2225Vrms

(4)
2225Vrms

(1) Power supply

(2) Including 10% from EN 61010
(3) Non inductive
(4) Isolating voltage

23
 PNP

0.14 - 2.5mm
(AWG 26-14)

25/26
max. 0,4A
max. 4A

PE + -

(1)
20...40V DC 10% (2), max. 0.5A

(1) Power supply

(2) Including 10% from EN 61010

24
Functional grounding

by process connection

(5)

(5)

(5)

(5)

(6)

(5) Metal
(6) Use flat gasket, no teflon tape

25
alternative by cable

(7)

(8)

(7) Use internal or external terminal

(8) Grounded metal parts in case of non metal bin

26
Settings

Relay SPDT

29

14

(1)

(1) Signal delay

27
Relay DPDT / PNP

(1)

29

14

(1) Signal delay

28
Signal output logic

gelb(6) grn(5)

grn(5) gelb(6)

(1) = Relais SPDT

(2) = Relay DPDT
(3) = PNP
(4) = LED Signal
(5) =green
(6)= yellow

29
Weather protection cover

for Ex only approved for Zone 22

Maintenance

30
Spare parts

CN 4020 120C
SPDT 21..27V DC pl406100
DPDT 21..230V AC pl406110
21..45V DC
PNP 20..40V DC pl406120 SPDT

CN 4020 180C
DPDT

21..230V AC
21..45V DC
pl406111
DPDT
PNP 20..40V DC pl406121

CN 4030 / CN 4050
No spare parts available
PNP

31
ATEX + IEC-Ex
Notes

Permitted relative pressure

-0,2...+0,1bar
(-2.9+1.45psi)

Ambient temperature max. Surface temperature

T
60C (140F) CN 4020: 120C (248F) 120C (248F)
60C (140F) CN 4030: 110C (230F 120C (248F)
60C (140F) CN 4050: 80C (176F) 135C (275F)

CN 4020: CN 4020:
60C (140F) 120C (248F) 120C (248F)
60C (140F) 130C (266F) 130C (266F)
60C (140F) 140C (284F) 140C (284F)
60C (140F) 150C (302F) 150C (302F)
60C (140F) 160C (320F) 160C (320F)
60C (140F) 170C (338F) 170C (338F)
60C (140F) 180C (356F) 180C (356F)

32
Ex: Installation

(1)

(2)

(1) A pull relief must be provided

(2) Connect with equipotential bonding of the plant

33
ATEX / IEC-Ex: Further Remarks

For installation and field wiring the respectively valid installation regulations of the
respective country must be observed.
Commissioning only with closed lid.
Do not remove the lid (cover) while circuits are alive.
Before opening the lid take care, that no dust deposits or whirlings are present.
The installation has to be carried out in a way, that mechanical friction or impact
does not cause sparks between the aluminium enclosure and steel.
Cable glands:
Installation according to the regulations of the country, where the product is
installed.
Not used entries have to be closed with blanking elements certified for this
purpose.
Where applicable the factory provided parts must be used.
A strain relief must be provided for the field wiring cables, when the device is
installed with the factory
provided cable glands.
The diameter of the field wiring cable must match to the clamping range of the
cable clamp.
If other than the factory provided parts are used, following must be ensured:
The parts must have an approval adequate to the approval of the level sensor
(certificate and type of protection).
The approved temperature range must be from the min. ambient temperature of
the level sensor to the max. ambient temperature of the level sensor increased by
10K.
The parts must be mounted according to the instructions of the supplier.

34
 EC Declaration of conformity

Manufacturer UWT-GmbH, 87488 Betzigau, Westendstr. 5

Type Level Limit Switch

Serie CN 4000
2006/95/EG
Applied standards: EN 61 010-1

2004/108/EG
Applied standards: EN 61 326
94/9/EG (optional)
EC-Type Examination BVS 12 ATEX E 034
Certificate: DEKRA EXAM GmbH
ID number: 0158
Applied standards: IEC 60079-0
EN 60079-11
EN 60079-31
Note: Units which are manufactured according to the directive 94/9/EC are
respectively marked on the nameplate. Units without this marking are not
approved for use in Hazardous Areas (explosive atmospheres).

We hereby confirm that the above-mentioned unit corresponds with the essential
safety targets which are fixed in the above mentioned directives.

Signee information: Dipl. Ing. (FH) A. Haug, Technical Manager

Date: 03/2014 Signature:

35