Scribd
Upload
4K views2 pages

Lifterror Code

lift

Uploaded by

Navaneetha Krishnan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
4K views2 pages

Lifterror Code

lift

Uploaded by

Navaneetha Krishnan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 2
Function of the Switch MONO( MON1 = MON1 [MONO [Function LED Indicator o | o Error Display see "2 0 | 1 _|indicate the car position Indicate the car position levels 0 Indicate the range is from -19 to 19.0 and -0 0 represents the middle points of travel. 0 Indicator "1" means 256mm, 0 | 2 |Writes the load weight (for installation) |See* 0 | 3 indicate foor No. Indicate floor No. 0 | 4 _|indicate the floor No. Indicate floor No. 0 | 5 |Writes te load weight (for servicing) __|See*3 0 | 6 _|HAND proiority mode for installation Indicate "H" + floor No. 0 | 7 _|indicates foor No. Indicates floor No, 0 | 8 indicates floor No. Indicates floor No, 0 | 9 _|indicates floor No. Indicates floor No. 0 | A_|Annuis for intelligent door Indicates floor No, o | 8 | _ 0 | c _|check over load buzzer see "4. 0 | _D_|indicate load weight see "3. o |e |— o | F | Checks TSD running Indicate floor No. *2 Error Display ( When there are two or more errors the relevent code will appear for 2 seconds for each alternately) [7SEG2|7SEG1 ‘Content E | 0 _|No error ( There is no erro releven to the code 1 to F) |SWTGBL Abnormally low speed detection. ISWTGBH Over speed detection. ISWTGBR Reverse-run detection. |SWAST Anti-stole timer |SSIOCFO (IOCH) Over current detection ISSCOVH Over voltage detection ISSLVLT Low voltage detection SWCFLB # LB OFF failure ISWCFS #5 OFF failure |SWCFBK On failure of brake contact, ISTSTSCE Error in serial transmission to car. |STSTSHE Error in serial transmission to hall ISTSYER System error. |SDDNRS Unable to re-start. ( For Drive) mr Ya Yr Yen Yr Yr Yorn Jorn Jom Jr frm Jom Jr Jr nfm Jo Jo Jos |» Jo Jor |x Jo for | foo fro | |SWNRS Unable to re- start. (For control) *5 Indication state of elevator and current, floor and function of MON [ MON1 = 0/4] 21 _— 22 —> — PWFH(PPS down cal — flickering [7SEG3] TSEG2 TSEG1 The current floor ( Synchro floor + Z floor* ) is indecated ( Decimal system) * means /J Disance with the level of bottom floor. Normally "01" is indicated at the bottom floor. If selector error is detected, the selector error is held and the &SEG2 &1 indicators are flicked, During rising operation, the indecation of the rising floor to be written is flickered. There is an error in 7SEG2,1 , see detail for section 8-2 item 2) “2. Indicates contents of 7SEG3 below.. Name Function 29 [Check safety circuit 89 [Order for driving ( HAND mode) Light up when normal ( AUTO mode) PWFH(P-P) | Check phase of order and antiphase 21 [Order for door opening 22 [Order for door closing, [UP-Call [Upward direction Down- Call__[Downward direction.

You might also like