Scribd
Upload
756 views

Linear DC Machine PDF

The document describes how a linear DC machine operates as both a motor and generator by reversing current direction depending on whether an external force opposes or aids the machine's motion, maintaining steady-state speed and balance of forces in both cases through feedback between induced voltage/current and mechanical force. It also discusses starting the machine and examples of applying loads that cause it to function as a motor or generator.

Uploaded by

Abdul Aziz
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
756 views

Linear DC Machine PDF

The document describes how a linear DC machine operates as both a motor and generator by reversing current direction depending on whether an external force opposes or aids the machine's motion, maintaining steady-state speed and balance of forces in both cases through feedback between induced voltage/current and mechanical force. It also discusses starting the machine and examples of applying loads that cause it to function as a motor or generator.

Uploaded by

Abdul Aziz
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 21

Linear DC Machine

Starting of Linear DC Machine

To start the machine, the switch is closed.


Current will flow in the circuit and the equation can be
derived from Kirchoffs law:
At this moment, the induced voltage is 0 due to no movement
of the wire (the bar is at rest).
As the current flows down through the bar, a force will be
induced on the bar. (Effect 2: current flowing through a wire in
the presence of a magnetic field induces a force in the wire).

Direction of motion: to the RIGHT (From Flemings LEFT hand


rule)
When the bar starts to move, its velocity will increase, and a
voltage appears across the bar. (Effect 3)

Direction of induced potential: Positive upwards


Due to the presence of motion and induced potential (Eind),
the current flowing in the bar will reduce (according to
Kirchhoffs voltage law). The result of this action is that
eventually the bar will reach a constant steady-state speed
where the net force on the bar is zero. This occurs when Eind
has risen all the way up to equal VB. This is given by:

The above equation is true assuming that R is very small. The


bar will continue to move along at this no-load speed forever
unless some external force disturbs it. Summarization of the
starting of linear DC machine can be represented by the
following graphs:
Linear DC Machine acting as a motor

Assume the linear machine is initially running at the no-load


steady state condition.
What happens when an external load is applied?
A force Fload is applied to the bar opposing the direction of
motion. Since the bar was initially at steady state, application
of the force Fload will result in a net force on the bar in the
direction opposite the direction of motion.

Thus, the bar will slow down (the resulting acceleration a =


Fnet/m is negative). As soon as that happens, the induced
voltage on the bar drops.
When the induced voltage drops, the current flow in the bar
will rise:

Thus, the induced force will rise too!


A force Fload is applied to the bar opposing the direction of
motion. Since the bar was initially at steady state, application
of the force Fload will result in a net force on the bar in the
direction opposite the direction of motion.

Thus, the bar will slow down (the resulting acceleration a =


Fnet/m is negative). As soon as that happens, the induced
voltage on the bar drops.
When the induced voltage drops, the current flow in the bar
will rise:

Thus, the induced force will rise too!


Final result: The induced force will rise until it is equal and
opposite to the load force, and the bar again travels in steady
state condition, but at a lower speed. See graphs below:
Now, there is an induced force in the direction of motion and
power is being converted from electrical to mechanical form
to keep the bar moving.

The power converted is Pconv = Eind i = Find v

An amount of electric power equal to Eind i is consumed and


is replaced by the mechanical power Find v MOTOR

The power converted in a real rotating motor is:


Pconv = ind
Linear DC Machine acting as a generator

Assume the linear machine is initially running at the no-load


steady state condition.
A force in the direction of motion is applied. (supplied by
prime mover)
The applied force will cause the bar to accelerate in the
direction of motion, and the velocity v will increase.

When the velocity increase, Eind will increase and will be larger
than VB. When Eind > VB the current reverses direction.

Since the current now flows up through the bar, it induces a


force in the bar (Find = ilB to the left). This induced force
opposes the applied force on the bar.

Final result: the induced force will be equal and opposite to


the applied force, and the bar will move at a higher speed
than before. The linear machine no is converting mechanical
power Find v to electrical power Eind i GENERATOR

The power converted in a real generator is: Pconv = ind


Assignment:
Sketch the graphs of Linear DC machine acting
as a generator, with the initial condition being
the machine moving at steady state velocity
after starting with no load. State max. and
min. points of each graph using constants
Due: Before start of last class next week
Notes
The same machine acts as both motor and generator. The only
difference is whether the externally applied force is in the
direction of motion (generator) or opposite to the direction of
motion (motor).
Electrically, (Eind > VB generator) or (Eind < VB motor)
Whether the machine is a motor or a generator, both induced
force (motor action) or induced voltage (generator action) is
present at all times.
Both actions are present, and it is only the relative directions
of the external forces with respect to the direction of motion
that determine whether the overall machine behaves as a
motor or as a generator.
Whether it was a motor or a generator, it always moved in the
same direction.
There is a merely a small change in operating speed and a
reversal of current flow.
Starting Problem of Motor &
Numerical example
This machine is supplied by a 250V DC source and internal
resistance R is 0.1 ohm
At starting, the speed of the bar is zero, Eind = 0. The current
flow at start is:
istart = V/R = 250/0.1 = 2500A

This current is very high (10x in excess of the rated current).


How to prevent?
Solution: insert an extra resistance into the circuit during
starting to limit current flow until Eind builds up enough to
limit it, as shown here:
Example

A linear dc machine is as shown in the figure above.

(a) What is the machines maximum starting current? What is the


steady state velocity at no load?
(b) Suppose a 30N force pointing to the right were applied to the
bar. What would the steady-state speed be? How much
power would the bar be producing or consuming? How much
power would the bar be producing or consuming? Is the
machine acting as a motor or a generator?
(c) Now suppose a 30N force pointing to the left were applied to
the bar. What would the new steady-state speed be? Is the
machine a motor or generator now?
Assignment:

You might also like