x3250 m1 Guide

IBM System x3250 Types 4364 and 4365

Users Guide

IBM System x3250 Types 4364 and 4365

Users Guide
Note:
Before using this information and the product it supports, be sure to read the general information in
Notices, on page 49, and the Warranty and Support Information document on the IBM System x
Documentation CD.
Third Edition (January 2007)

Copyright International Business Machines Corporation 2007. All rights reserved.
US Government Users Restricted Rights Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Chapter 1. The System x3250 Types 4364 and 4365 server . . . . . . . . 1

Related documentation . . . . . . . . . . . . . . . . . . . . . . 1
Notices and statements in this document . . . . . . . . . . . . . . . . 2
Features and specifications . . . . . . . . . . . . . . . . . . . . . 3
What your server offers . . . . . . . . . . . . . . . . . . . . . . 4
Reliability, availability, and serviceability features . . . . . . . . . . . . . 5
IBM Director . . . . . . . . . . . . . . . . . . . . . . . . . . 5
The UpdateXpress program . . . . . . . . . . . . . . . . . . . . 6
Server controls, LEDs, and power . . . . . . . . . . . . . . . . . . 7
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Server power features . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2. Installing optional devices . . . . . . . . . . . . . . . . 11

Server components . . . . . . . . . . . . . . . . . . . . . . . 11
System-board internal connectors . . . . . . . . . . . . . . . . . 12
System-board switches and jumpers . . . . . . . . . . . . . . . . 13
System-board external connectors . . . . . . . . . . . . . . . . . 14
System-board LEDs . . . . . . . . . . . . . . . . . . . . . . 15
System-board optional-device connectors . . . . . . . . . . . . . . 16
Installation guidelines . . . . . . . . . . . . . . . . . . . . . . 16
System reliability guidelines . . . . . . . . . . . . . . . . . . . 17
Handling static-sensitive devices . . . . . . . . . . . . . . . . . 18
Removing the cover . . . . . . . . . . . . . . . . . . . . . . . 18
Installing an adapter . . . . . . . . . . . . . . . . . . . . . . . 19
Installing a Remote Supervisor Adapter II SlimLine . . . . . . . . . . . . 23
Installing a hard disk drive . . . . . . . . . . . . . . . . . . . . . 24
Installing a simple-swap Serial ATA hard disk drive . . . . . . . . . . . 24
Installing a hot-swap hard disk drive . . . . . . . . . . . . . . . . 25
Installing a new CD or DVD drive . . . . . . . . . . . . . . . . . . 26
Installing a memory module . . . . . . . . . . . . . . . . . . . . 28
Installing a SATA RAID kit . . . . . . . . . . . . . . . . . . . . . 30
Completing the installation. . . . . . . . . . . . . . . . . . . . . 32
Installing the cover . . . . . . . . . . . . . . . . . . . . . . 33
Connecting the cables . . . . . . . . . . . . . . . . . . . . . 33
Updating the server configuration . . . . . . . . . . . . . . . . . 34
Chapter 3. Configuring the server . . . . . . . . . . . . . . . . . 35

Using the ServerGuide Setup and Installation CD . . . . . . . . . . . . 36
ServerGuide features . . . . . . . . . . . . . . . . . . . . . 36
Setup and configuration overview . . . . . . . . . . . . . . . . . 37
Typical operating-system installation . . . . . . . . . . . . . . . . 37
Installing your operating system without using ServerGuide . . . . . . . 37
Using the Configuration/Setup Utility program . . . . . . . . . . . . . 38
Starting the Configuration/Setup Utility program . . . . . . . . . . . . 38
Configuration/Setup Utility menu choices . . . . . . . . . . . . . . 38
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . 41
Using the LSI Logic Configuration Utility program . . . . . . . . . . . . 43
Starting the LSI Logic Configuration Utility program . . . . . . . . . . 43
Configuring the controller and devices . . . . . . . . . . . . . . . 44
Using the baseboard management controller . . . . . . . . . . . . . . 44
Copyright IBM Corp. 2007 iii

Installing the SMBridge management utility program . . . . . . . . . . 44
Using the baseboard management controller utility programs . . . . . . . 46
Configuring the Gigabit Ethernet controllers . . . . . . . . . . . . . . 47
Updating IBM Director . . . . . . . . . . . . . . . . . . . . . . 47
Appendix. Notices . . . . . . . . . . . . . . . . . . . . . . . 49
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . 50
Product recycling and disposal . . . . . . . . . . . . . . . . . . . 51
Battery return program . . . . . . . . . . . . . . . . . . . . . . 52
Electronic emission notices . . . . . . . . . . . . . . . . . . . . 53
Federal Communications Commission (FCC) statement . . . . . . . . . 53
Industry Canada Class A emission compliance statement . . . . . . . . 53
Australia and New Zealand Class A statement . . . . . . . . . . . . 53
United Kingdom telecommunications safety requirement . . . . . . . . . 53
European Union EMC Directive conformance statement . . . . . . . . . 54
Taiwanese Class A warning statement . . . . . . . . . . . . . . . 54
Chinese Class A warning statement . . . . . . . . . . . . . . . . 54
Japanese Voluntary Control Council for Interference (VCCI) statement . . . 54
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
iv IBM System x3250 Types 4364 and 4365: Users Guide

Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informaes de Segurana.
Pred instalac tohoto produktu si prectete prrucku bezpecnostnch instrukc.
Ls sikkerhedsforskrifterne, fr du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tmn tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant dinstaller ce produit, lisez les consignes de scurit.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) fr du installerer dette produktet.
Antes de instalar este produto, leia as Informaes sobre Segurana.
Copyright IBM Corp. 2007 v

Antes de instalar este producto, lea la informacin de seguridad.
Ls skerhetsinformationen innan du installerar den hr produkten.
vi IBM System x3250 Types 4364 and 4365: Users Guide

Important:
Each caution and danger statement in this document is labeled with a number. This
number is used to cross reference an English-language caution or danger
statement with translated versions of the caution or danger statement in the Safety
Information document.
For example, if a caution statement is labeled Statement 1, translations for that

caution statement are in the Safety Information document under Statement 1.
Be sure to read all caution and danger statements in this document before you
perform the procedures. Read any additional safety information that comes with the
server or optional device before you install the device.
Statement 1:
DANGER
Electrical current from power, telephone, and communication cables is

hazardous.
To avoid a shock hazard:

v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet.
v Connect to properly wired outlets any equipment that will be attached to
this product.
v When possible, use one hand only to connect or disconnect signal
cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached
devices.
To Connect: To Disconnect:
1. Turn everything OFF. 1. Turn everything OFF.

2. First, attach all cables to devices. 2. First, remove power cords from outlet.
3. Attach signal cables to connectors. 3. Remove signal cables from connectors.
4. Attach power cords to outlet. 4. Remove all cables from devices.
5. Turn device ON.
Safety vii
Statement 2:
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has
a module containing a lithium battery, replace it only with the same module
type made by the same manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
v Throw or immerse into water
v Heat to more than 100C (212F)
v Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
viii IBM System x3250 Types 4364 and 4365: Users Guide
Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
v Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
v Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
Class 1 Laser Product

Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A` Laser de Classe 1
Safety ix
Statement 4:
18 kg (39.7 lb) 32 kg (70.5 lb) 55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
2
1
x IBM System x3250 Types 4364 and 4365: Users Guide

Statement 8:
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect a problem with one of these parts, contact
a service technician.
Statement 26:
CAUTION:
Do not place any object on top of rack-mounted devices.
This server is suitable for use on an IT power-distribution system whose maximum

phase-to-phase voltage is 240 V under any distribution fault condition.
Safety xi
xii IBM System x3250 Types 4364 and 4365: Users Guide
Chapter 1. The System x3250 Types 4364 and 4365 server
The IBM System x3250 Type 4364 and Type 4365 server is a 1-U-high server that
is ideally suited for networking environments that require superior microprocessor
performance, efficient memory management, and flexibility.
Performance, ease of use, reliability, and expansion capabilities were key

considerations in the design of the server. These design features make it possible
for you to customize the system hardware to meet your needs today and provide
flexible expansion capabilities for the future.
The server comes with a limited warranty. For information about the terms of the
warranty and getting service and assistance, see the Warranty and Support
Information document.
The server contains IBM X-Architecture technologies, which help increase

performance and reliability. For more information, see What your server offers on
page 4 and Reliability, availability, and serviceability features on page 5.
You can obtain up-to-date information about the server and other IBM server
products at http://www.ibm.com/systems/x/.
Related documentation
This Users Guide contains general information about the server, including how to
install supported optional devices and how to configure the server. The following
documentation also comes with the server:
v Installation Guide
This printed document contains instructions for setting up the server and basic
instructions for installing some optional devices.
v Warranty and Support Information
This document is in Portable Document Format (PDF) on the System x
Documentation CD. It contains information about the terms of the warranty and
getting service and assistance.
v Safety Information
This document is in PDF on the IBM System x Documentation CD. It contains
translated caution and danger statements. Each caution and danger statement
that appears in the documentation has a number that you can use to locate the
corresponding statement in your language in the Safety Information document.
v Rack Installation Instructions
This printed document contains instructions for installing the server in a rack.
v Problem Determination and Service Guide
This document is in PDF on the IBM System x Documentation CD. It contains
information to help you solve problems yourself, and it contains information for
service technicians.
Depending on the server model, additional documentation might be included on the

IBM System x Documentation CD.
The System x and xSeries Tools Center is an online information center that
contains information about tools for updating, managing, and deploying firmware,
Copyright IBM Corp. 2007 1

device drivers, and operating systems. The System x and xSeries Tools Center is at
http://publib.boulder.ibm.com/infocenter/toolsctr/v1r0/index.jsp.
The server might have features that are not described in the documentation that
comes with the server. The documentation might be updated occasionally to include
information about those features, or technical updates might be available to provide
additional information that is not included in the server documentation. These
updates are available from the IBM Web site. To check for updated documentation
and technical updates, complete the following steps.
Note: Changes are made periodically to the IBM Web site. The actual procedure
might vary slightly from what is described in this document.
1. Go to http://www.ibm.com/servers/eserver/support/xseries/index.html.
2. From the Hardware list, select System x3250 and click Go.
3. Click the Install and use tab.
4. Click Product documentation.
Notices and statements in this document

The caution and danger statements in this document are also in the multilingual
Safety Information document, which is on the IBM System x Documentation CD.
Each statement is numbered for reference to the corresponding statement in the
Safety Information document.
The following notices and statements are used in this document:

v Note: These notices provide important tips, guidance, or advice.
v Important: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
v Attention: These notices indicate potential damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage could occur.
v Caution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure step or situation.
v Danger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
2 IBM System x3250 Types 4364 and 4365: Users Guide

Features and specifications
The following information is a summary of the features and specifications of the
server. Depending on the server model, some features might not be available, or
some specifications might not apply.
Racks are marked in vertical increments of 4.45 cm (1.75 inches). Each increment
is referred to as a unit, or U. A 1-U-high device is 1.75 inches tall.
Table 1. Features and specifications
Microprocessor: Power supply: Acoustical noise emissions:
One Intel LGA 775 Xeon 3000 351 watt (110 or 220 V ac v Sound power, idling: 6.5 bel
series, Pentium D, or Celeron D, auto-sensing) maximum
depending on the server model v Sound power, operating: 6.5 bel
Note: Use the Configuration/Setup Size: maximum
Utility program to determine the size v Height: 43 mm (1.75 inches, 1 U)
of the L2 cache, speed of the v Depth: 559 mm (22 inches) Heat output:
microprocessor, and speed of the v Width: 440 mm (17.32 inches) Approximate heat output in British
front-side bus. v Maximum weight: 12.7 kg (28 lb) thermal units (Btu) per hour:
depending on your configuration v Minimum configuration: 341 Btu per
Memory: hour (100 watts)
v Minimum: One or two 512 MB Integrated functions: v Maximum configuration: 1024 Btu
DIMMs, depending on the server v Two Broadcom NetXtreme GB per hour (300 watts)
model Ethernet controllers on the system
v Maximum: 8 GB board with Wake on LAN support Electrical input:
v Type: PC2-5300, 667 MHz, ECC, v Serial port v Sine-wave input (47 - 63 Hz)
DDR II unbuffered SDRAM DIMMs v Four USB ports (two on front and required
only two on rear of server) v Input voltage low range:
v Slots: Four dual inline v Keyboard port Minimum: 100 V ac
v Supports 512 MB, 1 GB, and 2 GB v Mouse port Maximum: 127 V ac
DIMMs v Systems-management port if an v Input voltage high range:
optional Remote Supervisor Minimum: 200 V ac
Drives: Adapter II SlimLine is installed Maximum: 240 V ac
Ultrabay Enhanced: CD or CD/DVD v Approximate input kilovolt-amperes
Hard disk controllers: (kVA):
Expansion bays: v Serial ATA (SATA) controller Minimum: 0.102 kVA
One of the following configurations: (simple-swap SATA models) Maximum: 0.55 kVA
v Two 3.5-inch slim-high bays for v Serial-attached SCSI (SAS)
controller with integrated RAID Notes:
hard disk drives.
(hot-swap SAS/SATA models) 1. Power consumption and heat
Hot-swap models: Supports
output vary depending on the
maximum of two serial-attached
Environment: number and type of optional
SCSI (SAS) drives or two serial
v Air temperature: features that are installed and the
ATA (SATA) drives.
Server on: 10 to 35C (50.0 power-management optional
Simple-swap models: Supports
to 95.0F); altitude: 0 to 914.4 features that are in use.
maximum of two SATA drives
m (3000 ft) 2. These levels were measured in
v Four 2.5-inch small form-factor Server on: 10 to 32C (50.0 controlled acoustical environments
(SFF) hot-swap bays for hard disk to 89.6F); altitude: 914.4 m according to the procedures that
drives. Supports a maximum of four (3000 ft) to 2133 m (6998.0 ft) are specified by the American
2.5-inch SAS drives. Server off: 10 to 43C (50.0 National Standards Institute (ANSI)
to 109.4F); maximum altitude: S12.10 and ISO 7779 and are
Expansion slots: reported in accordance with ISO
2133 m (6998.0 ft)
Two PCI Express x8 slots, one 9296. Actual sound-pressure levels
Shipping: -40 to 60C
low-profile and one 3/4-length full in a given location might exceed
(-40 to 140F); maximum
height the average stated values because
altitude: 2133 m (6998.0 ft)
v Humidity: of room reflections and other
Video controller:
Server on: 8% to 80% nearby noise sources. The declared
v ATI ES1000 video on system board
Server off: 8% to 80% sound-power levels indicate an
v 16 MB DDR video memory
upper limit, below which a large
number of computers will operate.
Chapter 1. The System x3250 Types 4364 and 4365 server 3

What your server offers
The server uses the following features and technologies:
v Baseboard management controller
The baseboard management controller provides basic service-processor
environmental monitoring functions. If an environmental condition exceeds a
threshold or if a system component fails, the baseboard management controller
lights LEDs to help you diagnose the problem. Critical errors are also included in
the error log.
Note: In messages and documentation, the term service processor refers to the
baseboard management controller or the optional Remote Supervisor Adapter II
SlimLine.
v IBM Director
IBM Director is a workgroup-hardware-management tool that you can use to
centrally manage servers. For more information, see the IBM Director
documentation on the IBM Director CD.
v IBM Enterprise X-Architecture technology
IBM X-Architecture technology combines proven, innovative IBM designs to make
your x86-processor-based server powerful, scalable, and reliable. For more
information, see http://www.ibm.com/servers/eserver/xseries/xarchitecture/
enterprise/index.html.
v Large system-memory capacity
The server supports up to 8 GB of system memory. The memory controller
supports error correcting code (ECC) for up to four industry-standard PC2-5300,
667 MHz, ECC, double-data-rate (DDR) II unbuffered synchronous dynamic
random access memory (SDRAM) dual inline memory modules (DIMMs).
v IBM ServerGuide Setup and Installation CD
The ServerGuide Setup and Installation CD that comes with the server provides
programs to help you set up the server and install a Windows operating system.
The ServerGuide program detects installed optional hardware devices and
provides the correct configuration programs and device drivers. For more
information about the ServerGuide Setup and Installation CD, see Using the
ServerGuide Setup and Installation CD on page 36.
v Integrated network support
The server comes with two integrated Broadcom Gigabit controllers, which
support connection to a 10 Mbps, 100 Mbps, or 1000 Mbps network. For more
information, see Configuring the Gigabit Ethernet controllers on page 47.
v Large data-storage capacity
The server supports up to two 25.4 mm (1-inch) slim-high, 3.5-inch hard disk
drives (Serial Advanced Technology Attachment (SATA) or serial-attached SCSI
(SAS), depending on server model), or up to four 63.5 mm (2.5-inch) hard disk
drives (SAS), depending on server model.
v ServeRAID support
The hot-swap models of this server contain an internal SAS controller that
supports level 0 and level 1 redundant array of independent disks (RAID)
configurations. The server also supports some ServeRAID adapters and other
optional devices to create RAID configurations. For a list of supported ServeRAID
devices for the server, see http://www.ibm.com/servers/eserver/serverproven/
compat/us/.

v Systems-management capabilities
The server supports an optional IBM Remote Supervisor Adapter II SlimLine.
When this adapter is used with the integrated baseboard management controller
that comes with the server, you can manage the functions of the server locally
and remotely. The Remote Supervisor Adapter II SlimLine also provides system
monitoring, event recording, and dial-out alert capability.
Reliability, availability, and serviceability features

Three important server design features are reliability, availability, and serviceability
(RAS). The RAS features help to ensure the integrity of the data that is stored in
the server, the availability of the server when you need it, and the ease with which
you can diagnose and repair problems.
The server has the following RAS features:

v Advanced Configuration and Power Interface (ACPI)
v Advanced Desktop Management Interface (DMI) features
v Intelligent Platform Management Interface (IPMI) 1.5 support that provides secure
remote power on/power off and seven standard alerts for components such as
fans, voltage, and thermals
v Automatic restart after power failure
v Auto-restart initial program load (IPL)
v Boot-block recovery
v Built-in, menu-driven configuration and setup programs
v Cooling fans with speed-sensing capability
v Customer-upgradeable basic input/output system (BIOS) code
v ECC memory
v Error codes and messages
v Menu-driven diagnostic programs on CD
v Monitoring support for temperature, voltage, and fan speed
v Parity checking on the SAS bus and PCI bus
v Power-on self-test (POST)
v Read-only memory (ROM) checksums
v SDRAM with serial presence detect (SPD)
v Server management
v Standby voltage for systems management features and monitoring
v System error log
v Vital product data (VPD); includes information stored in nonvolatile memory for
easier remote viewing
v Wake on LAN
IBM Director
With IBM Director, a network administrator can perform the following tasks:
v View the hardware configuration of remote systems, in detail
v Monitor the usage and performance of critical components, such as
microprocessors, disks, and memory

v Centrally manage individual or large groups of IBM and non-IBM x86-based
servers, desktop computers, workstations, and notebook computers on a variety
of platforms
IBM Director provides a comprehensive entry-level workgroup hardware manager. It

includes the following key features:
v Advanced self-management capabilities for maximum system availability
v Multiple operating-system platform support, including Microsoft Windows 2000
Server, Windows Server 2003, Windows XP Professional, AIX, i5/OS, Red Hat
Linux, SUSE Linux, VMware, and Novell NetWare. For a complete list of
operating systems that support IBM Director, see the IBM Director Compatibility
Document. This document is in Portable Document Format (PDF) at
http://www.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-61788. It is
updated every 6 to 8 weeks.
v Support for IBM and non-IBM servers, desktop computers, workstations, and
notebook computers
v Support for systems-management industry standards
v Integration into leading workgroup and enterprise systems-management
environments
v Ease of use, training, and setup
IBM Director also provides an extensible platform that supports advanced server
tools that are designed to reduce the total cost of managing and supporting
networked systems. By deploying IBM Director, you can achieve reductions in
ownership costs through the following benefits:
v Reduced downtime
v Increased productivity of IT personnel and users
v Reduced service and support costs
For more information about IBM Director, see the documentation on the IBM
Director CD that comes with the server, the IBM Director Information Center at
http://publib.boulder.ibm.com/infocenter/eserver/v1r2/topic/diricinfo/ fqm0_main.html,
and the IBM System x and xSeries Systems Management Web page at
http://www.ibm.com/servers/eserver/xseries/systems_management/, which presents
an overview of IBM Systems Management and IBM Director.
The UpdateXpress program

The UpdateXpress program is available for most System x servers and optional
devices. It detects supported and installed device drivers and firmware in the server
and installs available updates. You can download the UpdateXpress program from
the Web at no additional cost, or you can purchase it on a CD. To download the
program or purchase the CD, go to http://www.ibm.com/servers/eserver/xseries/
systems_management/ibm_director/extensions/xpress.html. Additional information
about UpdateXpress is available from the System x and xSeries Tools Center at
http://publib.boulder.ibm.com/infocenter/toolsctr/v1r0/index.jsp.

Server controls, LEDs, and power
This section describes the controls and light-emitting diodes (LEDs) and how to turn
the server on and off.
Note: The illustrations in this document show the 3.5-inch hard disk drive models,
unless specifically indicated otherwise.
Front view
The following illustration shows the controls, light-emitting diodes (LEDs), and
connectors on the front of the server.
Hard disk drive activity LED
Locator LED
Reset button System-error LED
Power-control button USB 1 connector
Power-on LED
USB 2 connector
CD-eject button
CD drive activity LED
Power-on LED: When this LED is lit and not flashing, it indicates that the server is
turned on. When this LED is flashing, it indicates that the server is turned off and
still connected to an ac power source. When this LED is off, it indicates that ac
power is not present, or the power supply or the LED itself has failed.
Note: If this LED is off, it does not mean that there is no electrical power in the
server. The LED might be burned out. To remove all electrical power from the
server, you must disconnect the power cord from the electrical outlet.
Power-control button: Press this button to turn the server on and off manually. A
power-control-button shield comes installed around the button to prevent the server
from being turned off accidentally. You can remove this disk-shaped shield if you
prefer.
Reset button: Press this button to reset the server and run the power-on self-test
(POST). You might have to use a pen or the end of a straightened paper clip to
press the button.
Hard disk drive activity LED: When this LED is flashing, it indicates that a hard
disk drive is in use.
Locator LED: This LED can be lit remotely by the system administrator to aid in
visually locating the server. You can use IBM Director to light this LED remotely.
System-error LED: When this LED is lit, it indicates that a system error has
occurred. An LED on the system board might also be lit to help isolate the error.
Detailed troubleshooting information is in the Problem Determination and Service
Guide that is on the IBM System x Documentation CD.
USB connectors: Connect a USB device to either of these connectors.
CD-eject button: Press this button to release a CD from the CD drive.

CD drive activity LED: When this LED is lit, it indicates that the CD drive is in use.
Rear view
The following illustration shows the LEDs on the rear of the server.
Ethernet 1 transmit / receive Ethernet 2 speed LED

activity LED
Ethernet 2 transmit / receive
Ethernet 1 speed LED activity LED
Ethernet transmit/receive activity LED: This LED is on each Ethernet connector.

When this LED is lit, it indicates that there is activity between the server and the
network.
Ethernet speed LED: This LED is on each Ethernet connector. When this LED is
lit, it indicates that the Ethernet network speed is 1 Gbps. When this LED is off, it
indicates that the Ethernet network speed is 10 Mbps or 100 Mbps.
The following illustration shows the connectors on the rear of the server.
Mouse connector
Power-cord connector Keyboard connector
Systems-management USB 3 connector Serial connector

connector
USB 4 connector Video connector
Ethernet 2 connector
Power-cord connector: Connect the power cord to this connector.
Keyboard connector: Connect a PS/2 keyboard to this connector.
Mouse connector: Connect a mouse or other PS/2 device to this connector.
Serial connector: Connect a 9-pin serial device to this connector.
Video connector: Connect a monitor to this connector.
Ethernet connector: Use either of these connectors to connect the server to a

network.
USB connector: Connect a USB device to either of these connectors.
Systems-management connector: Connect the server to a network for

systems-management information control. This connector is active only if you have
installed a Remote Supervisor Adapter II SlimLine, and it is used only by the
Remote Supervisor Adapter II SlimLine.

Server power features
When the server is connected to an ac power source but is not turned on, the
operating system does not run, and all core logic except for the service processor is
shut down; however, the server can respond to requests from the service processor
(the baseboard management controller), such as a remote request to turn on the
server.
Turning on the server

Approximately 20 seconds after the server is connected to ac power, the
power-control button becomes active, and one or more fans might start running to
provide cooling while the server is connected to power. You can turn on the server
and start the operating system by pressing the power-control button.
The server can also be turned on in any of the following ways:

v If a power failure occurs while the server is turned on, the server will restart
automatically when power is restored.
v If your operating system supports the systems-management software for an
optional Remote Supervisor Adapter II SlimLine, the systems-management
software can turn on the server.
v If your operating system supports the Wake on LAN feature, the Wake on LAN
feature can turn on the server.
Note: When 4 GB or more of memory (physical or logical) is installed, some

memory is reserved for various system resources and is unavailable to the
operating system. The amount of memory that is reserved for system resources
depends on the operating system, the configuration of the server, and the
configured PCI optional devices.
Turning off the server

When you turn off the server and leave it connected to ac power, the server can
respond to requests from the service processor, such as a remote request to turn
on the server. While the server remains connected to ac power, one or more fans
might continue to run. To remove all power from the server, you must disconnect it
from the power source.
Some operating systems require an orderly shutdown before you turn off the server.
See your operating-system documentation for information about shutting down the
operating system.

Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
2
1
The server can be turned off in any of the following ways:
v You can turn off the server from the operating system, if your operating system
supports this feature. After an orderly shutdown of the operating system, the
server will be turned off automatically.
v You can press the power-control button to start an orderly shutdown of the
operating system and turn off the server, if your operating system supports this
feature.
v If the operating system stops functioning, you can press and hold the
power-control button for more than 4 seconds to turn off the server.
v If an optional Remote Supervisor Adapter II SlimLine is installed in the server, the
server can be turned off from the Remote Supervisor Adapter II SlimLine user
interface.
v The integrated systems-management processor (mini-BMC) can turn off the
server as an automatic response to a critical system failure.
v You can turn off the server through a request from the service processor.

Chapter 2. Installing optional devices
This chapter provides detailed instructions for installing optional hardware devices in
the server.
Server components
The following illustration shows the major components in the server. The
illustrations in this document might differ slightly from your hardware.
Riser-card
Assembly
DIMM
Heat sink
SAS/SATA controller
(some models)
Microprocessor System board
SAS/SATA backplane
(some models)
Air baffle
SATA simple-swap
back panel (some models)
Fans
Power supply
CD/DVD interface card
Operator information
panel assembly
CD/DVD
drive
3.5-inch hot-swap
hard disk drive 2.5-inch hard
(some models) disk drive
backplane
Fans
3.5-inch drive cage
3.5-inch simple-
Bezel swap SATA
hard disk drive 2.5-inch
(some models) 2.5-inch hard drive cage
Hot-swap hard
disk drive filler disk drive
Simple-swap SATA filler 2.5-inch filler panel

System-board internal connectors
The following illustration shows the internal connectors on the system board.
Wake on LAN connector
SATA 2 connector
SATA 0 connector
Power connector
SAS/SATA controller
card connector
Front USB connector
Operator information
panel connector
Hot-swap SAS/SATA
backplane power
connector
SAS signal connector
(some models)
Fan 3 connector Power connector

Fan 2 connector Fan 5 connector
Fan 1 connector Microprocessor connection Fan 4 connector
IDE connector
Important: Use only a supported IBM SAS/SATA controller in the SAS/SATA
controller card connector. For a list of supported optional devices for the server, see
http://www.ibm.com/servers/eserver/serverproven/compat/us/

System-board switches and jumpers
The following illustration shows the switches and jumpers on the system board.
Clear CMOS jumper
Boot block
recovery jumper
The following illustration identifies the pins on a jumper and shows the location of
pin 1.
Pin 1 mark 1
Table 2. Switch and jumper settings

Component Settings
CMOS jumper (JP3) v Pins 1 and 2: Keep CMOS data (default)
v Pins 2 and 3: Clear the CMOS data, which clears the
power-on password and administrator password
Boot block jumper (JP4) v Pins 1 and 2: Normal (default)
v Pins 2 and 3: Boot from boot block
Chapter 2. Installing optional devices 13

System-board external connectors
The following illustration shows the external connectors on the system board.
Keyboard/mouse Serial connector

connector Video connector
USB 4 connector
USB 3 connector
Systems-
management
connector

System-board LEDs
The following illustration shows the light-emitting diodes (LEDs) on the system
board.
DIMM 4
error LED
DIMM 3
error LED
DIMM 2
error LED
DIMM 1
error LED
Voltage
regulator
error LED
Standby
power
LED
Fan 3
error LED
Fan 2 Baseboard
error LED management
controller
Fan 1 heartbeat
error LED
LED
Fan 5 error LED

Fan 4 error LED
Table 3. System-board LEDs

LED Description
Error LEDs When one of these LEDs is lit, it indicates that the associated
component has failed.
Baseboard management This LED flashes to indicate that the mini-BMC is functioning
controller heartbeat LED normally.
Standby power LED When this LED is lit, it indicates that the server is connected
to ac power.

System-board optional-device connectors
The following illustration shows the connectors for user-installable optional devices.
Riser-card
connector
Remote Supervisor
Adapter II SlimLine
DIMM 1 connector
connector
Other
systems-management
DIMM 2
adapter connector
connector
DIMM 3
connector Battery connector
DIMM 4
connector
SAS/SATA controller
connector
The following illustration shows the location of the PCI Express slots on the
riser-card assembly.
PCI Express x8 slot 1
PCI Express x8 slot 2
Installation guidelines
Before you install optional devices, read the following information:
v Read the safety information that begins on page v and the guidelines in
Handling static-sensitive devices on page 18. This information will help you
work safely.
v When you install your new server, take the opportunity to download and apply
the most recent firmware updates. This step will help to ensure that any known
issues are addressed and that your server is ready to function at maximum levels
of performance. To download firmware updates for your server, go to
http://www.ibm.com/servers/eserver/support/xseries/index.html, select System
x3250 from the Hardware list, click Go, and then click the Download tab. For
additional information about tools for updating, managing, and deploying
firmware, see the System x and xSeries Tools Center at http://
publib.boulder.ibm.com/infocenter/toolsctr/v1r0/index.jsp.

v Before you install optional hardware devices, make sure that the server is
working correctly. Start the server, and make sure that the operating system
starts, if an operating system is installed, or that a 19990305 error code is
displayed, indicating that an operating system was not found but the server is
otherwise working correctly. If the server is not working correctly, see
Diagnostics in the Problem Determination and Service Guide for diagnostic
information.
v Observe good housekeeping in the area where you are working. Place removed
covers and other parts in a safe place.
v If you must start the server while the cover is removed, make sure that no one is
near the server and that no tools or other objects have been left inside the
server.
v Do not attempt to lift an object that you think is too heavy for you. If you have to
lift a heavy object, observe the following precautions:
Make sure that you can stand safely without slipping.
Distribute the weight of the object equally between your feet.
Use a slow lifting force. Never move suddenly or twist when you lift a heavy
object.
To avoid straining the muscles in your back, lift by standing or by pushing up
with your leg muscles.
v Make sure that you have an adequate number of properly grounded electrical
outlets for the server, monitor, and other devices.
v Back up all important data before you make changes to disk drives.
v Have a small flat-blade screwdriver available.
v You do not have to turn off the server to install or replace hot-plug Universal
Serial Bus (USB) devices.
v Blue on a component indicates touch points, where you can grip the component
to remove it from or install it in the server, open or close a latch, and so on.
v Orange on a component or an orange label on or near a component indicates
that the component can be hot-swapped, which means that if the server and
operating system support hot-swap capability, you can remove or install the
component while the server is running. (Orange can also indicate touch points on
hot-swap components.) See the instructions for removing or installing a specific
hot-swap component for any additional procedures that you might have to
perform before you remove or install the component.
v When you are finished working on the server, reinstall all safety shields, guards,
labels, and ground wires.
v For a list of supported optional devices for the server, see http://www.ibm.com/
servers/eserver/serverproven/compat/us/.
System reliability guidelines

To help ensure proper system cooling and system reliability, make sure that the
following requirements are met:
v Each of the drive bays has a drive or a filler panel and electromagnetic
compatibility (EMC) shield installed in it.
v If the server has redundant power, each of the power-supply bays has a power
supply installed in it.
v There is adequate space around the server to allow the server cooling system to
work properly. Leave approximately 50 mm (2.0 in.) of open space around the
front and rear of the server. Do not place objects in front of the fans. For proper
cooling and airflow, replace the server cover before turning on the server.

Operating the server for extended periods of time (more than 30 minutes) with
the server cover removed might damage server components.
v You have followed the cabling instructions that come with optional adapters.
v You have replaced a failed fan within 48 hours.
v You have replaced a hot-swap drive within 2 minutes of removal.
Handling static-sensitive devices

Attention: Static electricity can damage the server and other electronic devices.
To avoid damage, keep static-sensitive devices in their static-protective packages
until you are ready to install them.
To reduce the possibility of damage from electrostatic discharge, observe the

following precautions:
v Limit your movement. Movement can cause static electricity to build up around
you.
v The use of a grounding system is recommended but is not required. For
example, wear an electrostatic-discharge wrist strap, if one is available.
v Handle the device carefully, holding it by its edges or its frame.
v Do not touch solder joints, pins, or exposed circuitry.
v Do not leave the device where others can handle and damage it.
v While the device is still in its static-protective package, touch it to an unpainted
metal part of the server for at least 2 seconds. This drains static electricity from
the package and from your body.
v Remove the device from its package and install it directly into the server without
setting down the device. If it is necessary to set down the device, put it back into
its static-protective package. Do not place the device on the server cover or on a
metal surface.
v Take additional care when you handle devices during cold weather. Heating
reduces indoor humidity and increases static electricity.
Removing the cover

To remove the cover, complete the following steps:
1. Read the safety information that begins on page v and Installation guidelines
on page 16.
2. Turn off the server and all attached devices (see Turning off the server on
page 9).
3. Disconnect all external cables and power cords.

4. Remove the server from the rack and place it on a flat, static-protective surface.
Cover-release
button
5. Press the cover-release button.

6. Slide the cover back approximately 1.27 cm (0.5 inches); then, lift it off the
server.
Attention: For proper cooling and airflow, replace the cover before you turn on
the server. Operating the server for extended periods of time (more than 30
minutes) with the cover removed might damage server components.
Installing an adapter
The following notes describe the types of adapters that the server supports and
other information that you must consider when you install an adapter:
v Locate the documentation that comes with the adapter and follow those
instructions in addition to the instructions in this section. If you have to change
switch settings or jumper settings on the adapter, follow the instructions that
come with the adapter.
v The adapter slots are on the riser-card assembly. You must first remove the
riser-card assembly to access the adapter slots.
v The two PCI Express slots on the riser-card assembly support PCI Express x8
1.0a adapters.
v You can install one full-height three-quarter-length adapter in expansion slot 1
and one low-profile half-length adapter in expansion slot 2.
v An optional Remote Supervisor Adapter II SlimLine can be installed only in the
dedicated connector on the system board (see System-board optional-device
connectors on page 16 for the location of the connector). To install the Remote
Supervisor Adapter II SlimLine, see Installing a Remote Supervisor Adapter II
SlimLine on page 23.
v Because of mechanical interference, when an optional Remote Supervisor
Adapter II SlimLine is installed in the server, you cannot install an adapter in
expansion slot 1.
v The server uses a rotational interrupt technique to configure PCI Express
adapters so that you can install PCI Express adapters that do not support
sharing of interrupts.
v An optional ServeRAID 8s controller provides RAID level 5 support to the
hot-swap drives. A ServeRAID 8s controller supports the 2.5-inch hard disk drives
without modification. To use a ServeRAID 8s controller with hot-swap 3.5-inch

drives, you must connect the controller to the hard disk drive backplane with a
SAS signal cable that is 58 cm (22.8 in.) long. See http://www.ibm.com/servers/
eserver/serverproven/compat/us/ for information about ordering the cable.
v An optional IBM SAS HBA Controller adapter enables you to connect external
storage devices, such as SAS or SATA hard disk drives or tape drives, to a
simple-swap SATA model server.
v The server scans the PCI slots to assign system resources. The scan sequence
is related to the startup sequence. If you have not changed the default startup
sequence, the server scans the PCI slots in the following order: the integrated
Ethernet controllers 1 and 2; then, the drives connected to the SAS/SATA
controller; then, the PCI Express slots 1 and 2.
Expansion-slot Adapter
bracket
Adapter support
bracket
Expansion slot 1
Riser-card
assembly
Expansion slot 2
To install an adapter, complete the following steps:

on page 16.
2. Turn off the server and peripheral devices, and disconnect the power cord and
all external cables.
3. Remove the cover (see Removing the cover on page 18).

Riser-card
assembly
4. Grasp the riser-card assembly at the rear edge and lift to remove it from the
server. Place the riser-card assembly on a flat, static-protective surface.
5. Remove the expansion-slot cover from the slot that you intend to use.
Attention: PCI expansion-slot covers must be installed on all vacant slots.
This maintains the electronic emissions characteristics of the server and
ensures proper cooling of server components.
6. Touch the static-protective package that contains the adapter to any unpainted
metal surface on the server. Then, remove the adapter from the
static-protective package. Avoid touching the components and gold-edge
connectors on the adapter.
7. Place the adapter, component side up, on a flat, static-protective surface and
set any jumpers or switches as described by the adapter manufacturer, if
necessary.
8. To install the adapter in the riser-card assembly, carefully grasp the adapter by
its top edge or upper corners, and align it with the expansion slot; then, press
the adapter firmly into the expansion slot.
9. Follow the cabling instructions, if any, that come with the adapter.
10. Carefully align the riser-card assembly with the guides on the rear of the
server and with the riser-card connectors on the system board; then, press
down on the assembly. Make sure that the riser-card assembly is fully seated
in the riser-card connector on the system board.
11. If you are installing a ServeRAID 8s controller, complete the following steps:
a. Disconnect the existing SAS/SATA controller signal cable from the hard
disk drive backplane and from the controller; then, remove the cable from
the server.
b. In a server with 2.5-inch drives, route the ServeRAID 8s signal cable as
shown in the following illustration and connect it to the hard disk drive
backplane.

c. In a server with 3.5-inch drives, route the ServeRAID 8s signal cable as
shown in the following illustration and connect it to the hard disk drive
backplane.
If you have other devices to install or remove, do so now. Otherwise, go to

Completing the installation on page 32.

Installing a Remote Supervisor Adapter II SlimLine
Install an optional Remote Supervisor Adapter II SlimLine in the Remote Supervisor
Adapter II SlimLine connector on the system board. See the illustration in
System-board optional-device connectors on page 16 for the location of the
connector. After the Remote Supervisor Adapter II SlimLine is installed, the
systems-management port on the rear of the server is active.
Because of mechanical interference, when the Remote Supervisor Adapter II

SlimLine is installed, you cannot install an adapter in expansion slot 1.
Notes:
1. When you start the server for the first time after you install a Remote Supervisor
Adapter II SlimLine, the startup process will take several minutes longer than a
typical startup.
2. Earlier versions of the Remote Supervisor Adapter II SlimLine might not work in
this server. See http://www.ibm.com/servers/eserver/serverproven/compat/us/ for
the supported Remote Supervisor Adapter II SlimLine versions.
To install a Remote Supervisor Adapter II SlimLine, complete the following steps.

Remote Supervisor Adapter II SlimLine
Mounting bracket
Mounting bracket
retention latch
Mounting bracket
Remote Supervisor
Adapter II Slimline connector
Rear of system
on page 16.
2. Turn off the server and peripheral devices and disconnect all power cords and
external cables (see Turning off the server on page 9); then, remove the cover
(see Removing the cover on page 18).
3. Grasp the riser-card assembly at the rear edge and lift to remove it from the
server. Place the riser-card assembly on a flat, static-protective surface.
4. Put the protective plastic cover on the Remote Supervisor Adapter II SlimLine.
5. Turn the Remote Supervisor Adapter II SlimLine so that the keys on the
connector align correctly with the connector on the system board.
6. At a downward angle, insert the free end of the adapter under the tab on the
mounting bracket, aligning the holes in the adapter with the posts on the
mounting bracket. Rotate the rear of the adapter into the rear mounting bracket,
aligning the holes in the adapter with the posts on the rear mounting bracket.

7. Press the Remote Supervisor Adapter II SlimLine firmly into the connector and
make sure that all tabs on both mounting brackets secure the adapter in place.
Attention: Incomplete insertion might cause damage to the server or the
adapter.
8. If an adapter is installed in expansion slot 1 on the riser-card assembly, remove
it.
9. Carefully align the riser-card assembly with the guides on the rear of the server
and with the riser-card connectors on the system board; then, press down on
the assembly. Make sure that the riser-card assembly is fully seated in the
riser-card connectors on the system board.
See the documentation that comes with the Remote Supervisor Adapter II SlimLine
for information about installing the firmware and configuring the adapter. Create a
backup copy of the configuration so that if you have to replace the adapter in the
future, you can restore the configuration.

Installing a hard disk drive

Locate the documentation that comes with the hard disk drive and follow those
instructions in addition to the instructions in this chapter.
Attention: To avoid damage to the hard disk drive connectors, make sure that the
cover is in place and fully closed whenever you install or remove a hard disk drive.
Installing a simple-swap Serial ATA hard disk drive

Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all
power from the server before you remove or install a simple-swap hard disk drive.
To install a simple-swap Serial ATA hard disk drive, complete the following steps.
Note: If you have only one hard disk drive, install it in the left drive bay.
SATA hard disk

drive back plate
Hard disk
drive assembly
Filler panel

on page 16.
2. Make sure that the server cover is in place and fully closed.
4. Remove the filler panel from the bay.
5. Pull the loops of the drive tray toward each other, and slide the drive into the
server until the drive connects to the back plate.
6. Release the loops of the drive tray.
7. Insert the filler panel into the bay to cover the drive.
If you have other devices to install, do so now. Otherwise, go to Completing the

installation on page 32.
Note: If a RAID controller or adapter is installed, you might have to reconfigure the
disk arrays after you install hard disk drives. See your RAID controller or adapter
documentation.
To remove a simple-swap SATA drive from the bay, complete the following steps:
on page 16.
4. Pull the loops of the drive tray toward each other and pull the tray out of the
bay.
Installing a hot-swap hard disk drive

The 3.5-inch drive hot-swap server models support either two SAS 3.5-inch hard
disk drives or two SATA 3.5-inch hard disk drives. The 2.5-inch drive hot-swap
server models support four 2.5-inch SAS hard disk drives.
2.5-inch drives
The installation procedure is the same for any of these drives. The illustrations in
this procedure show 3.5-inch SAS drives.
To install a hot-swap hard disk drive, complete the following steps.
Note: If you have only one hard disk drive, install it in the left or upper-left drive
bay.

on page 16.
2. Make sure that the server cover is in place and fully closed.
Attention: To maintain proper system cooling, do not operate the server for
more than 10 minutes without either a drive or filler panel installed in each bay.
4. Install the hard disk drive in the hot-swap bay:
a. Make sure that the tray handle is open (that is, perpendicular to the front of
the drive).
b. Align the drive assembly with the guide rails in the bay.
c. Gently push the drive assembly into the bay until the drive stops.
d. Push the tray handle to the closed (locked) position.
e. Check the hard disk drive status LED to make sure that the hard disk drive
is operating correctly. If the amber hard disk drive status LED for a drive is
lit continuously, that drive is faulty and must be replaced. If the green hard
disk drive activity LED is flashing, the drive is being accessed.
If you have other devices to install, do so now. Otherwise, go to Completing the

installation on page 32.
Installing a new CD or DVD drive

The server comes with a CD or CD/DVD drive installed. You can remove the drive
and install a different one. See the ServerProven list at http://www.ibm.com/
servers/eserver/serverproven/compat/us/ for a list of CD or CD/DVD drives you can
use with the server.
To remove a CD or CD/DVD drive, complete the following steps.

on page 16.
2. Turn off the server and peripheral devices, and disconnect the power cords and
all external cables. Remove the cover (see Removing the cover on page 18).
3. Press the release tab (the rear of the drive-retention clip) toward the drive to
release the clip; then, while pressing the tab, pull the drive out of the bay.
Note: You might have to push the right-rear corner of the drive toward the front
of the server to move the drive initially.
4. Remove the retention clip from the drive and save it for future use.
To install a CD or DVD drive, complete the following steps:

on page 16.
2. Make sure that the server and peripheral devices are turned off and that the
power cords and all external cables are disconnected. Remove the cover (see
Removing the cover on page 18).
3. Follow the instructions that come with the drive to set any jumpers or switches.

4. Attach the drive retention clip to the side of the drive.
5. Slide the drive into the CD/DVD drive bay until the drive clicks into place.

Installing a memory module

The following notes describe the types of dual inline memory modules (DIMMs) that
the server supports and other information that you must consider when you install
DIMMs:
v The server supports 512 MB, 1 GB, and 2 GB DIMMs, for a maximum of 8 GB of
system memory. See http://www.ibm.com/servers/eserver/serverproven/compat/
us/ for a list of memory modules that you can use with the server.
v The amount of usable memory will be reduced depending on the system
configuration. A certain amount of memory must be reserved for system
resources. Use the system summary in the Configuration/Setup Utility program to
view the total amount of installed memory and the amount of configured memory
(see Using the Configuration/Setup Utility program on page 38).
v The server comes with one 512 MB DIMM installed in DIMM connector 1. Some
models come with a second 512 MB DIMM installed in DIMM connector 3. If one
DIMM is installed, when you install an additional DIMM, you must install it in
DIMM connector 3, and it must be the same size, speed, type, and technology as
the DIMM that is installed in DIMM connector 1. You can mix compatible DIMMs
from various manufacturers. The third and fourth DIMMs must be installed as a
pair, in DIMM connectors 2 and 4.
v If you install a pair of DIMMs in DIMM connectors 2 and 4, they do not have to
be the same size, speed, type, and technology as the DIMMs that are installed in
DIMM connectors 1 and 3. However, the size, speed, type, and technology of the
DIMMs that you install in DIMM connectors 2 and 4 must match each other.
v Install only double-data-rate II (DDR II), PC2-5300, unbuffered synchronous
dynamic random-access memory (SDRAM) with error correcting code (ECC)
DIMMs. These DIMMs must be compatible with the latest PC2-5300 SDRAM
unbuffered DIMM specification.
v If you install a pair of 2 GB DIMMs and a pair of other-size DIMMs, the 2 GB
DIMMs must be installed as the first pair (in DIMM connectors 1 and 3).
v When you restart the server after you add or remove a DIMM, a message is
displayed indicating that the memory configuration has changed.

To remove a DIMM, complete the following steps:
on page 16.
Attention: To avoid breaking the retaining clips or damaging the DIMM
connectors, open and close the clips gently.
3. Open the retaining clip on each end of the DIMM connector.
4. Lift the DIMM out of the connector.
To install a DIMM, complete the following steps:

on page 16.
Attention: To avoid breaking the retaining clips or damaging the DIMM
connectors, open and close the clips gently.
3. Open the retaining clip on each end of the DIMM connector.
4. Touch the static-protective package that contains the DIMM to any unpainted
metal surface on the server. Then, remove the DIMM from the package.
5. Turn the DIMM so that the DIMM keys align correctly with the slot.
6. Insert the DIMM into the connector by aligning the edges of the DIMM with the
slots at the ends of the DIMM connector. Firmly press the DIMM straight down
into the connector by applying pressure on both ends of the DIMM
simultaneously. The retaining clips snap into the locked position when the DIMM
is firmly seated in the connector. If there is a gap between the DIMM and the
retaining clips, the DIMM has not been correctly inserted; open the retaining
clips, remove the DIMM, and then reinsert it.


Installing a SATA RAID kit
The SATA RAID kit provides level 0 and level 1 RAID support for 3.5-inch
simple-swap SATA drives.
SAS signal cable
SAS/SATA controller
Power cable
Power cable
Air deflector
Guide channel
To install the SATA RAID kit, complete the following steps:

on page 16.
3. Remove the server from the rack and place it on a flat, static-protective
surface.
4. Remove the cover (see Removing the cover on page 18).
SATA hard disk

drive back plate
Hard disk
drive assembly
Filler panel
5. Pull the hard disk drives out of the server slightly to disengage them from the
back plate or remove the drives completely (see page 25 for instructions).
6. Disconnect the SATA cables from the system board (see System-board
internal connectors on page 12 for the location of the SATA connectors).

SATA cables
Air deflector
Guide channel
7. Remove the SATA back plate from the server:

a. Rotate (lift) the air deflector out of the way.
b. Lift the back plate out of the server slightly; then, disconnect the power
cables and remove the back plate.
8. Install the SAS/SATA controller.
Note: If you have installed an adapter in expansion slot 1, you might have to
remove the riser-card assembly before you can install the SAS/SATA controller.
See Installing an adapter on page 19 for instructions to remove the riser-card
assembly.
a. Grasp the edges of the SAS/SATA controller.
SAS/SATA Notch
controller card
Tab
b. Gently insert the controller card into the SAS/SATA controller card
connector on the system board (see the illustration on page System-board
internal connectors on page 12 for the location of the connector) while you
align the holes in the card with the two plastic alignment pins on the
system board.
c. Press the controller card firmly onto the alignment pins until the card clicks
into place. Make sure that the top of each alignment pin has expanded to
hold the controller card securely in place.
d. Push the controller card toward the rear of the server, fully into the
connector, until the side tabs on the connector rest in the side notches of
the controller card.

9. Install the SATA RAID kit back plate:
a. Make sure that the air deflector is in the open position.
b. Connect the power supply cables to the power cables on the SATA RAID
kit back plate.
c. Slide the back plate into the card guides, making sure that any nearby
wires or cables are not trapped or pinched.
d. Press firmly until the back plate is fully seated.
e. Rotate the air deflector into place, making certain that no cables are
pinched beneath it, and press it down firmly.
f. Connect the back plate cable to the signal connector on the SAS/SATA
controller.
10. Connect the cable from the back plate to the signal connector on the
SAS/SATA controller.
11. If you removed the riser-card assembly, reinstall it now. See Installing an
adapter on page 19 for instructions.
12. Install the cover (see Installing the cover on page 33).
13. Insert the hard disk drives that you removed in step 5 on page 30 fully into the
bays (see Installing a simple-swap Serial ATA hard disk drive on page 24 for
instructions).

Completing the installation.
Completing the installation

To complete the installation, complete the following steps:
1. Reinstall the cover. See Installing the cover on page 33 for more information.
2. Install the server in the rack cabinet. See the Rack Installation Instructions that
come with the server for detailed information about how to install the server in a
rack cabinet.
Attention:
v Install the server only in a rack cabinet that has perforated doors.
v Do not leave open space above or below an installed server in the rack
cabinet. To help prevent damage to server components, always install a filler
panel to cover the open space and to help ensure proper air circulation. See
the documentation that comes with the rack cabinet for more information.
3. Connect the cables and power cords. For more information, see Connecting
the cables on page 33.
4. Update the server configuration. See Updating the server configuration on
page 34 for more information.

Installing the cover
To install the cover, place it into position and slide it forward.
Connecting the cables

The following illustrations show the locations of the input and output connectors on
the front and rear of the server.
Front
USB 1 connector
USB 2 connector
Rear
Mouse connector
Power-cord connector Keyboard connector
Systems-management USB 3 connector Serial connector

connector
USB 4 connector Video connector
You must turn off the server before you connect or disconnect cables.
See the documentation that comes with any external devices for additional cabling
instructions. It might be easier for you to route cables before you connect the
devices to the server.
Cable identifiers are printed on the cables that come with the server and devices.
Use these identifiers to connect the cables to the correct connectors.
If the server comes with an installed operating system, see the documentation that
comes with the operating system for additional cabling instructions.

There is one keyboard connector on the back of the server. Use this connector to
connect the server to a keyboard or optional console switch. You can also connect
a USB keyboard to the server by using one of the USB connectors. After you install
a USB keyboard, you might have to use the Configuration/Setup Utility program to
enable keyboardless operation and prevent the POST error message 301 from
being displayed during startup. For information about how to connect a USB
keyboard to the server, see the documentation that comes with the keyboard. If the
server cables and connector panel have color-coded connectors, match the color of
each cable end with the color of the connector. For example, match a blue cable
end to a blue connector on the panel, a red cable end to a red connector, and so
on.
Updating the server configuration

When you start the server for the first time after you add or remove an internal
optional device or external SAS device, you might receive a message that the
configuration has changed. The Configuration/Setup Utility program starts
automatically so that you can save the new configuration settings. For more
information, see Chapter 3, Configuring the server, on page 35.
Some optional devices have device drivers that you must install. For information
about installing device drivers, see the documentation that comes with each device.
If the server has a RAID configuration that uses the SAS/SATA controller with
integrated RAID (hot-swap SATA or SAS models only) and you have installed or
removed a hard disk drive, you might have to reconfigure the disk arrays.
If the server has an optional RAID adapter and you have installed or removed a
hard disk drive, see the documentation that comes with the RAID adapter for
information about reconfiguring the disk arrays.
For information about configuring an integrated Gigabit Ethernet controller, see

Configuring the Gigabit Ethernet controllers on page 47.

Chapter 3. Configuring the server
The following configuration programs and capabilities come with the server:
v IBM ServerGuide Setup and Installation CD
The ServerGuide program provides software-setup tools and installation tools
that are designed for the server. Use this CD during the installation of the server
to configure basic hardware features and to simplify the installation of your
operating system. For information about using this CD, see Using the
ServerGuide Setup and Installation CD on page 36.
v Configuration/Setup Utility program
The Configuration/Setup Utility program is part of the basic input/output system
(BIOS). Use it to configure serial port assignments, change interrupt request
(IRQ) settings, change the startup-device sequence, set the date and time, and
set passwords. For information about using this program, see Using the
Configuration/Setup Utility program on page 38.
v LSI Logic Configuration Utility program
Use the LSI Logic Configuration Utility program to configure devices that are
attached to the SAS/SATA controller. For information about using this program,
see Using the LSI Logic Configuration Utility program on page 43.
Important: If the server is a simple-swap SATA model and you have installed an
optional SATA RAID Kit, you can use the LSI Logic Configuration Utility program
to configure the simple-swap SATA hard disk drives.
The following table lists the different server configurations and the applications
available for configuring and managing RAID arrays.
Table 4.
RAID array configuration RAID array management
(before operating system is (after operating system is
Server Configuration installed) installed)
Integrated SATA and no SAS None None
controller card installed
SAS/SATA controller card LSI Utility (BIOS Utility MyStorage (for monitoring
(LSI 1064) installed CTRL-C), ServerGuide storage only)
ServeRAID 8s adapter ServeRAID Manager ServeRAID Manager,
installed Hardware Boot CD, BIOS ARCCONF (CLI)
Utility (CTRL-A), ServerGuide
v Baseboard management controller utility programs

Use these programs to configure the baseboard management controller, to
update the firmware and sensor data record/field replaceable unit (SDR/FRU)
data, and to remotely manage a network. For information about using these
programs, see Using the baseboard management controller on page 44.
v Ethernet controller configuration
For information about configuring the Ethernet controllers, see Configuring the
Gigabit Ethernet controllers on page 47.
v IBM Director
IBM Director is a workgroup-hardware-management tool that you can use to
centrally manage System x servers. If you plan to use IBM Director to manage
the server, you must check for the latest applicable IBM Director updates and
interim fixes. For information about updating IBM Director, see Updating IBM

Director on page 47. For more information about IBM Director, see the IBM
Director documentation on the IBM Director CD that comes with the server.
Using the ServerGuide Setup and Installation CD

The ServerGuide Setup and Installation CD contains a setup and installation
program that is designed for your server. The ServerGuide program detects the
server model and optional hardware devices that are installed and uses that
information during setup to configure the hardware. The ServerGuide program
simplifies operating-system installations by providing updated device drivers and, in
some cases, installing them automatically.
If a later version of the ServerGuide program is available, you can download a free
image of the ServerGuide Setup and Installation CD, or you can purchase the CD.
To download the image, go to the IBM ServerGuide Web page at
http://www.ibm.com/pc/qtechinfo/MIGR-4ZKPPT.html. To purchase the latest
ServerGuide Setup and Installation CD, go to the ServerGuide fulfillment Web site
at http://www.ibm.com/servers/eserver/xseries/systems_management/serverguide/
sub.html.
The ServerGuide program has the following features:

v An easy-to-use interface
v Diskette-free setup, and configuration programs that are based on detected
hardware
v ServeRAID Manager program, which configures your ServeRAID adapter or
SAS/SATA controller with RAID capabilities
v Device drivers that are provided for the server model and detected hardware
v Operating-system partition size and file-system type that are selectable during
setup
ServerGuide features
Features and functions can vary slightly with different versions of the ServerGuide
program. To learn more about the version that you have, start the ServerGuide
Setup and Installation CD and view the online overview. Not all features are
supported on all server models.
The ServerGuide program requires a supported IBM server with an enabled

startable (bootable) CD drive. In addition to the ServerGuide Setup and Installation
CD, you must have your operating-system CD to install the operating system.
The ServerGuide program performs the following tasks:

v Sets system date and time
v Detects the SAS RAID adapter, controller, or integrated SAS/SATA controller with
RAID capabilities and runs the SAS RAID configuration program
v Checks the microcode (firmware) levels of a ServeRAID adapter and determines
whether a later level is available from the CD
v Detects installed optional hardware devices and provides updated device drivers
for most adapters and devices
v Provides diskette-free installation for supported Windows operating systems
v Includes an online readme file with links to tips for your hardware and
operating-system installation

Setup and configuration overview
When you use the ServerGuide Setup and Installation CD, you do not need setup
diskettes. You can use the CD to configure any supported IBM server model. The
setup program provides a list of tasks that are required to set up your server model.
On a server with a SAS/SATA controller with RAID capabilities, you can run the LSI
Logic Configuration Utility program to create logical drives.
Note: Features and functions can vary slightly with different versions of the
ServerGuide program.
When you start the ServerGuide Setup and Installation CD, the program prompts
you to complete the following tasks:
v Select your language.
v Select your keyboard layout and country.
v View the overview to learn about ServerGuide features.
v View the readme file to review installation tips for your operating system and
adapter.
v Start the operating-system installation. You will need your operating-system CD.
Typical operating-system installation

The ServerGuide program can reduce the time it takes to install an operating
system. It provides the device drivers that are required for your hardware and for
the operating system that you are installing. This section describes a typical
ServerGuide operating-system installation.
Note: Features and functions can vary slightly with different versions of the
ServerGuide program.
1. After you have completed the setup process, the operating-system installation
program starts. (You will need your operating-system CD to complete the
installation.)
2. The ServerGuide program stores information about the server model, service
processor, hard disk drive controllers, and network adapters. Then, the program
checks the CD for newer device drivers. This information is stored and then
passed to the operating-system installation program.
3. The ServerGuide program presents operating-system partition options that are
based on your operating-system selection and the installed hard disk drives.
4. The ServerGuide program prompts you to insert your operating-system CD and
restart the server. At this point, the installation program for the operating system
takes control to complete the installation.
Installing your operating system without using ServerGuide

If you have already configured the server hardware and you are not using the
ServerGuide program to install your operating system, complete the following steps
to download the latest operating-system installation instructions from the IBM Web
site.
Chapter 3. Configuring the server 37

5. Select the installation instructions for your operating system.
Using the Configuration/Setup Utility program

Use the Configuration/Setup Utility program to perform the following tasks:
v View configuration information
v View and change assignments for devices and I/O ports
v Set the date and time
v Set and change passwords
v View and change the startup characteristics of the server and the order of startup
devices (startup-drive sequence)
v View and change settings for advanced hardware features
v View and clear the error logs
v Change interrupt request (IRQ) settings
v Resolve configuration conflicts
Starting the Configuration/Setup Utility program

To start the Configuration/Setup Utility program, complete the following steps:
1. Turn on the server.
2. When the prompt Press F1 for Configuration/Setup is displayed, press F1. If
you have set both a power-on password and an administrator password, you
must type the administrator password to access the full Configuration/Setup
Utility menu. If you do not type the administrator password, a limited
Configuration/Setup Utility menu is available.
3. Select settings to view or change.
Configuration/Setup Utility menu choices

The following choices are on the Configuration/Setup Utility main menu. Depending
on the version of the BIOS code, some menu choices might differ slightly from
these descriptions.
v System Summary
Select this choice to view configuration information, including the type, speed,
and cache size of the microprocessor and the amount of installed memory. When
you make configuration changes through other choices in the Configuration/Setup
Utility program, the changes are reflected in the system summary; you cannot
change settings directly in the system summary.
This choice is on the full and limited Configuration/Setup Utility menu.
v System Information
Select this choice to view information about the server, such as the machine type
and model of the server, the serial number, the system UUID, the system board
identifier, and the revision level or issue date of the BIOS code. When you make
changes through other choices in the Configuration/Setup Utility program, some
of those changes are reflected in the system information; you cannot change
settings directly in the system information.
This choice is on the full Configuration/Setup Utility menu only.
v Devices and I/O Ports
Select this choice to view or change assignments for devices and input/output
(I/O) ports, to configure remote console redirection, and to enable or disable
integrated Ethernet controllers and all standard ports (such as serial and USB). If

you disable a device, it cannot be configured, and the operating system will not
be able to detect it (this is equivalent to disconnecting the device). If you disable
the integrated Ethernet controllers and no Ethernet adapter is installed, the
server will have no Ethernet capability.
v Date and Time
Select this choice to set the date and time in the server, in 24-hour format
(hour:minute:second).
v System Security
Select this choice to set passwords. For more information about passwords, see
Passwords on page 41.
Administrator Password
Select this choice to set or change an administrator password. An
administrator password is intended to be used by a system administrator; it
limits access to the full Configuration/Setup Utility menu. If an administrator
password is set, the full Configuration/Setup Utility menu is available only if
you type the administrator password at the password prompt. For more
information, see Administrator password on page 42.
Power-on Password
Select this choice to set or change a power-on password. For more
information, see Power-on password on page 41.
v Startup Options
Select this choice to view or change the startup options, such as the startup
sequence and the keyboard NumLock state. Changes in the startup options take
effect when you restart the server.
The startup sequence specifies the order in which the server checks devices to
find a boot record. The server starts from the first boot record that it finds. For
example, you can define a startup sequence that checks for a CD or DVD in the
CD or DVD drive, then checks the hard disk drive, and then checks a network
adapter. If the server has Wake on LAN hardware and software and the
operating system supports Wake on LAN functions, you can specify a startup
sequence for the Wake on LAN functions.
If you have not changed the default startup sequence, the server starts the
devices in the following order: the CD or DVD drive; then, the USB diskette drive,
USB memory key, USB CD drive, or USB hard disk drive, if you have installed
any in the server; then, the hard disk drives that are connected to the system
board; then, the drives connected to the SAS/SATA controller; then, the
integrated Ethernet controllers 1 and 2; then, the PCI Express slots 1 and 2.
v Advanced Setup
Select this choice to change settings for advanced hardware features.
Important: The server might malfunction if these choices are incorrectly
configured. Follow the instructions on the screen carefully.
CPU Options
Select this choice to enable or disable core multiprocessing, C1 enhanced
mode, and the execute-disable bit.
PCI Bus Control

Select this choice to view the system resources that are used by installed PCI
devices.
IPMI
Select this choice to change intelligent platform management interface (IPMI)
settings for the mini-BMC controller.
- IPMI Specification Version
This is a nonselectable menu item that displays the IPMI version.
- BMC Hardware/Firmware Version
This is a nonselectable menu item that displays the BMC firmware version.
- Clear System Event Log
Enable or disable clearing the system-event log at the next system startup,
which occurs when you save the settings and exit the Configuration/Setup
Utility program. Disable is the default setting.
- Existing Event Log number
This is a nonselectable menu item that displays the number of entries in
the system-event log.
- BIOS POST Watchdog
Enable or disable the mini-BMC POST watchdog. Disable is the default
setting.
- POST Watchdog Timeout
Set the mini-BMC POST watchdog timeout value. 5 minutes is the default
setting.
- System Event Log
Select this choice to view the mini-BMC system-event log, which contains
all system-error messages that have been generated. Use the arrow keys
to move between pages in the log. Run the diagnostic programs to get
more information about error codes that occur. See the Problem
Determination and Service Guide on the IBM System x Documentation CD
for instructions. Select Clear System Event Log to clear the mini-BMC
system-event log.
Important: If the system-error LED on the front of the server is lit but there
are no other error indications, clear the system-event log. This log does not
clear itself, and if it begins to fill up, the system-error LED will be lit. Also,
after you complete a repair or correct an error, clear the system-event log
to turn off the system-error LED on the front of the server.
- LAN Settings
Select this choice to view the mini-BMC MAC address, IP address, subnet
mask, and gateway address.
RSA II Settings
This choice is displayed only when a Remote Supervisor Adapter II SlimLine
is installed in the server.
Select this choice to view the IP address and DHCP settings for the Remote
Supervisor Adaptor II SlimLine, and to view or change the DHCP control,
static IP address, and operating system USB selections for the Remote
Supervisor Adaptor II SlimLine.
v Error Logs
Select this choice to view or clear error logs.
POST Error Log
Select this choice to view the three most recent error codes and messages
that the system generated during POST.
System Event/Error Log

Select this choice to view the complete log of POST error messages. If an
optional IBM Remote Supervisor Adapter II SlimLine is installed, the log also
contains system-event messages. Use the arrow keys to move between
pages in the log.
Run the diagnostic programs to get more information about error codes that
occur. See the Problem Determination and Service Guide on the IBM System
x Documentation CD for instructions.
To clear the system-event/error log, press Enter while you are viewing a log
entry.
v Save Settings
Select this choice to save the changes that you have made in the settings.
v Restore Settings
Select this choice to cancel the changes that you have made in the settings and
restore the previous settings.
v Load Default Settings
Select this choice to cancel the changes that you have made in the settings and
restore the factory settings.
v Exit Setup
Select this choice to exit from the Configuration/Setup Utility program. If you have
not saved the changes that you have made in the settings, you are asked
whether you want to save the changes or exit without saving them.
Passwords
From the System Security choice, you can set, change, and delete a power-on
password and an administrator password. The System Security choice is on the
full Configuration/Setup Utility menu only.
If you set only a power-on password, you must type the power-on password to
complete the system startup; you have access to the full Configuration/Setup Utility
menu.
An administrator password is intended to be used by a system administrator; it

limits access to the full Configuration/Setup Utility menu. If you set only an
administrator password, you do not have to type a password to complete the
system startup, but you must type the administrator password to access the
Configuration/Setup Utility menu.
If you set a power-on password for a user and an administrator password for a
system administrator, you can type either password to complete the system startup.
A system administrator who types the administrator password has access to the full
Configuration/Setup Utility menu; the system administrator can give the user
authority to set, change, and delete the power-on password. A user who types the
power-on password has access to only the limited Configuration/Setup Utility menu;
the user can set, change, and delete the power-on password, if the system
administrator has given the user that authority.
Power-on password
If a power-on password is set, when you turn on the server, the system startup will
not be completed until you type the power-on password. You can use any
combination of up to seven characters (A Z, a z, and 0 9) for the password.

If a power-on password is set, you can enable the Unattended Start mode, in which
the keyboard and mouse remain locked but the operating system can start. You can
unlock the keyboard and mouse by typing the power-on password.
If you forget the power-on password, you can regain access to the server in any of
the following ways:
v If an administrator password is set, type the administrator password at the
password prompt (see Administrator password). Start the Configuration/Setup
Utility program and reset the power-on password.
v Remove the battery from the server and then reinstall it. For instructions for
removing the battery, see the Problem Determination and Service Guide on the
IBM System x Documentation CD.
v Change the position of the clear CMOS jumper on the system board to bypass
the power-on password check. See Resetting passwords for additional
information.
Attention: Before you change any switch settings or move any jumpers, turn off
the server; then, disconnect all power cords and external cables. See the safety
information that begins on page v. Do not change settings or move jumpers on any
system-board switch or jumper block that is not shown in this document.
Administrator password
If an administrator password is set, you must type the administrator password for
access to the full Configuration/Setup Utility menu. You can use any combination of
up to seven characters (A Z, a z, and 0 9) for the password.
If you forget the administrator password, you can reset it after you change the
position of the clear CMOS jumper. See Resetting passwords for additional
information.
Resetting passwords
If you forget the power-on password or administrator password, you can move the
clear-CMOS jumper block on the system board to pins 2 and 3, to clear CMOS
memory and bypass the power-on or administrator password check. The jumper
location is shown in the following illustration.
Clear CMOS jumper

To clear CMOS and reset the passwords, complete the following steps.
Note: All configuration settings will be cleared by this action; you might have to
configure the settings again.
1. Review the safety information that begins on page v.
2. Turn off the server and peripheral devices and disconnect all power cords and
external cables.
3. Remove the server from the rack and place it on a flat, static-protective surface.
4. Remove the cover. See Removing the cover on page 18 for instructions.
5. Remove the riser-card assembly. See Installing an adapter on page 19 for
instructions.
6. Move the clear-CMOS jumper from pins 1 and 2 to pins 2 and 3 and leave it
there for at least 5 seconds; then, move the clear-CMOS jumper back to pins 1
and 2.
7. Reinstall the riser-card assembly and cover.
8. Replace the server in the rack and connect the server to a keyboard, monitor,
and mouse; then, connect the server to a power source.
9. Turn on the server. You can now start the Configuration/Setup Utility program
and either delete the old password or set a new power-on or administrator
password.
Using the LSI Logic Configuration Utility program

Use the LSI Logic Configuration Utility program to configure hot-swap hard disk
drives that are connected to the SAS/SATA controller.
Important: If the server is a simple-swap SATA model and you have installed an
optional SATA RAID Kit, you can use the LSI Logic Configuration Utility program to
configure the simple-swap SATA hard disk drives.
v If the server is a simple-swap SATA model and you have installed an optional
SATA RAID Kit, you can use the LSI Logic Configuration Utility program to
configure the simple-swap SATA hard disk drives.
v If you install an optional RAID controller in the server, such as the ServeRAID 8s
controller, use the configuration software that comes with the adapter to configure
the hard disk drives.
Starting the LSI Logic Configuration Utility program

To start the LSI Logic Configuration Utility program, complete the following steps:
1. Turn on the server.
2. When the prompt Press CTRL-C to start LSI Logic Configuration Utility...
is displayed, press Ctrl+C. If you have set an administrator password, you are
prompted to type the password.
3. Use the arrow keys to select the adapter (SAS controller) for which you want to
change settings. Use the Help function to see instructions and available actions
for this screen.
4. To change the settings of the selected items, follow the instructions on the
screen.
5. Press Enter to save your changes.

Configuring the controller and devices
To configure a SAS controller and attached devices, select the controller from the
initial LSI Logic Configuration Utility program screen; then, press Enter. You can
view and change settings for the following items for the selected controller:
Boot Support
Specify the type of boot support that will be in effect (disabled, BIOS only,
OS only, or both BIOS and OS)
RAID Properties
Create a RAID array from the displayed choices
SAS Topology
View information about the devices directly attached to the selected SAS
controller, and which devices make up RAID arrays. Format and verify an
attached device.
Advanced Adapter Properties
View the SAS properties and change the following items for the selected
controller:
v Global properties
v Cylinder head sector (CHS) mapping
v Advanced device properties, such as I/O timeouts and LUNs to scan
v Spinup properties
v PHY properties
Using the baseboard management controller

The mini-baseboard management controller provides basic environmental
monitoring for the server. If environmental conditions exceed thresholds or if system
components fail, the baseboard management controller lights LEDs to help you
diagnose the problem and also records the error in the mini-BMC system-event log.
Important: If the system-error LED on the front of the server is lit but there are no
other error indications, clear the system-event log and the system event/error log
(see Using the Configuration/Setup Utility program on page 38). These logs do not
clear themselves, and if either of them begins to fill up, the system-error LED will be
lit. Also, after you complete a repair or correct an error, clear the system-event log
to turn off the system-error LED on the front of the server.
The baseboard management controller also provides the command-line interface

(IPMI Shell) remote server management capabilities through the Avocent SMBridge
management utility program. The command-line interface provides direct access to
server management functions through the IPMI 1.5 protocol. Use the command-line
interface to issue commands to control the server power, view system information,
and identify the server. You can also save one or more commands as a text file and
run the file as a script.
Installing the SMBridge management utility program

To install the SMBridge management utility program on a server running a Windows
operating system, complete the following steps:
1. Go to http://www.ibm.com/servers/eserver/support/xseries/index.html and
download the utility program and create the BMC Management Utility CD.
2. Insert the BMC Management Utility CD into the drive. The InstallShield wizard
starts, and a window similar to that shown in the following illustration opens.

3. Follow the prompts to complete the installation.
The installation program prompts you for a TCP/IP port number and an IP
address. Specify an IP address, if you want to limit the connection requests that
will be accepted by the utility program. To accept connections from any server,
type INADDR_ANY as the IP address. Also specify the port number that the utility
program will use. These values will be recorded in the smbridge.cfg file for the
automatic startup of the utility program.
To install the Avocent SMBridge management utility program on a server running a

Linux operating system, complete the following steps . You must be logged in as a
root user to perform these procedures.
1. Go to http://www.ibm.com/servers/eserver/support/xseries/index.html and
download the management utility program and create the BMC Management
Utility CD.
2. Insert the BMC Management Utility CD into the drive.
3. Type mount/mnt/cdrom.
4. Locate the directory where the installation RPM package is located and type
cd/mnt/cdrom.
5. Type the following command to run the RPM package and start the installation:
rpm -ivh smbridge-2.0-xx.rpm
where xx is the release level being installed.

6. Follow the prompts to complete the installation. When the installation is
complete, the utility copies files to the following directories:
/etc/init.d/SMBridge
/etc/smbridge.cfg
/usr/sbin/smbridged
/var/log/smbridge/LICENSE

The utility starts automatically when the server is started. You can also locate the
/ect/init.d directory to start the utility and use the following commands to manage
the utility:
smbridge status
smbridge start
smbridge stop
smbridge restart
Note: For more information about the SMBridge management utility program, see
Using the SMBridge management utility program.
Using the baseboard management controller utility programs

Use the baseboard management controller utility programs to configure the
baseboard management controller, download firmware updates and SDR/FRU
updates, and remotely manage a network.
Using the baseboard management controller configuration utility

program
Use the baseboard management controller configuration utility program to view or
change the baseboard management controller configuration settings. You can also
use the utility program to save the configuration to a file for use on multiple servers.
Go to http://www.ibm.com/servers/eserver/support/xseries/index.html to download
the utility program. Run the utility program to create a configuration utility diskette.
Complete the following steps to start the baseboard management controller

configuration utility program:
1. Insert the configuration utility diskette into the diskette drive and restart the
server.
2. From a command-line prompt, type bmc_cfg and press Enter.
3. Follow the instructions on the screen.
Using the baseboard management controller firmware update

utility program
Use the baseboard management controller firmware update utility program to
download a baseboard management controller firmware update or a SDR/FRU
update. The firmware update utility program updates the baseboard management
controller firmware or SDR/FRU data only and does not affect any device drivers.
Go to http://www.ibm.com/servers/eserver/support/xseries/index.html to download
the utility program. Run the utility program to create a firmware update diskette.
Important: To ensure proper server operation, be sure to update the server

baseboard management controller firmware before you update the BIOS code.
To update the firmware, if the Linux or Windows operating-system update package

is available from the World Wide Web and you have obtained the applicable update
package, follow the instructions that come with the update package.
Using the SMBridge management utility program

Use the SMBridge management utility program to remotely manage and configure a
network. The utility program provides the CLI (command-line interface) remote
management capabilities.

Use CLI mode to remotely perform power-management and system identification
control functions over a LAN interface from a command-line interface. Use CLI
mode also to remotely view the system-event log.
Use the following commands in CLI mode:

v connect
Connect to the LAN. Type connect -ip ip_address -u username -p password.
v identify
Control the system-locator LED on the front of the server.
v power
Turn the server on and off remotely.
v reboot
Force the server to restart.
v sel
Perform operations with the system-event log.
v sysinfo
Display general system information that is related to the server and the
baseboard management controller.
Configuring the Gigabit Ethernet controllers

The Ethernet controllers are integrated on the system board. They provide an
interface for connecting to a 10 Mbps, 100 Mbps, or 1 Gbps network and provide
full-duplex (FDX) capability, which enables simultaneous transmission and reception
of data on the network. If the Ethernet ports in the server support auto-negotiation,
the controllers detect the data-transfer rate (10BASE-T, 100BASE-TX, or
1000BASE-T) and duplex mode (full-duplex or half-duplex) of the network and
automatically operate at that rate and mode.
You do not have to set any jumpers or configure the controllers. However, you must
install a device driver to enable the operating system to address the controllers. For
device drivers and information about configuring the Ethernet controllers, see the
Broadcom NetXtreme Gigabit Ethernet Software CD that comes with the server. To
find updated information about configuring the controllers, complete the following
steps.
Updating IBM Director

If you plan to use IBM Director to manage the server, you must check for the latest
applicable IBM Director updates and interim fixes.
To install the IBM Director updates and any other applicable updates and interim
fixes, complete the following steps.

1. Check for the latest version of IBM Director:
a. Go to http://www.ibm.com/servers/eserver/xseries/systems_management/
xseries_sm/dwnl.html.
b. If the drop-down list shows a newer version of IBM Director than what
comes with the server, follow the instructions on the Web page to download
the latest version.
2. Install IBM Director.
3. Download and install any applicable updates or interim fixes for the server:
a. Go to http://www.ibm.com/servers/eserver/support/xseries/index.html.
b. From the Hardware list, select System x3250 and click Go.
c. Click the Download tab.
d. Select any applicable update or interim fix that you want to download.
e. Click the link for the executable (.exe) file to download the file, and follow
the instructions in the readme file to install the update or interim fix.
4. Repeat steps 3d and 3e for any additional updates or interim fixes that you want
to install.

Appendix. Notices
This information was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this document in
other countries. Consult your local IBM representative for information on the
products and services currently available in your area. Any reference to an IBM
product, program, or service is not intended to state or imply that only that IBM
product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any IBM intellectual property right may be
used instead. However, it is the users responsibility to evaluate and verify the
operation of any non-IBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you any
license to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS

PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or
implied warranties in certain transactions, therefore, this statement may not apply to
you.
This information could include technical inaccuracies or typographical errors.

Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements and/or
changes in the product(s) and/or the program(s) described in this publication at any
time without notice.
Any references in this information to non-IBM Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for this
IBM product, and use of those Web sites is at your own risk.
IBM may use or distribute any of the information you supply in any way it believes
appropriate without incurring any obligation to you.
Trademarks
The following terms are trademarks of International Business Machines Corporation
in the United States, other countries, or both:
Active Memory IBM TechConnect

Active PCI IBM (logo) Tivoli
Active PCI-X IntelliStation Tivoli Enterprise
AIX NetBAY Update Connector
Alert on LAN Netfinity Wake on LAN

BladeCenter Predictive Failure Analysis XA-32
Chipkill ServeRAID XA-64
e-business logo ServerGuide X-Architecture
Eserver ServerProven XpandOnDemand
FlashCopy System x xSeries
i5/OS
Intel, Intel Xeon, Itanium, and Pentium are trademarks or registered trademarks of
Intel Corporation or its subsidiaries in the United States and other countries.
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in

the United States, other countries, or both.
UNIX is a registered trademark of The Open Group in the United States and other
countries.
Java and all Java-based trademarks and logos are trademarks of Sun
Microsystems, Inc. in the United States, other countries, or both.
Adaptec and HostRAID are trademarks of Adaptec, Inc., in the United States, other
countries, or both.
Linux is a trademark of Linus Torvalds in the United States, other countries, or both.
Red Hat, the Red Hat Shadow Man logo, and all Red Hat-based trademarks and
logos are trademarks or registered trademarks of Red Hat, Inc., in the United States
and other countries.
Other company, product, or service names may be trademarks or service marks of

others.
Important notes
Processor speeds indicate the internal clock speed of the microprocessor; other
factors also affect application performance.
CD drive speeds list the variable read rate. Actual speeds vary and are often less
than the maximum possible.
When referring to processor storage, real and virtual storage, or channel volume,
KB stands for approximately 1000 bytes, MB stands for approximately 1 000 000
bytes, and GB stands for approximately 1 000 000 000 bytes.
When referring to hard disk drive capacity or communications volume, MB stands

for 1 000 000 bytes, and GB stands for 1 000 000 000 bytes. Total user-accessible
capacity may vary depending on operating environments.
Maximum internal hard disk drive capacities assume the replacement of any
standard hard disk drives and population of all hard disk drive bays with the largest
currently supported drives available from IBM.
Maximum memory may require replacement of the standard memory with an

optional memory module.

IBM makes no representation or warranties regarding non-IBM products and
services that are ServerProven, including but not limited to the implied warranties of
merchantability and fitness for a particular purpose. These products are offered and
warranted solely by third parties.
IBM makes no representations or warranties with respect to non-IBM products.

Support (if any) for the non-IBM products is provided by the third party, not IBM.
Some software may differ from its retail version (if available), and may not include
user manuals or all program functionality.
Product recycling and disposal

This unit must be recycled or discarded according to applicable local and national
regulations. IBM encourages owners of information technology (IT) equipment to
responsibly recycle their equipment when it is no longer needed. IBM offers a
variety of product return programs and services in several countries to assist
equipment owners in recycling their IT products. Information on IBM product
recycling offerings can be found on IBMs Internet site at http://www.ibm.com/ibm/
environment/products/prp.shtml.
Esta unidad debe reciclarse o desecharse de acuerdo con lo establecido en la

normativa nacional o local aplicable. IBM recomienda a los propietarios de equipos
de tecnologa de la informacin (TI) que reciclen responsablemente sus equipos
cuando stos ya no les sean tiles. IBM dispone de una serie de programas y
servicios de devolucin de productos en varios pases, a fin de ayudar a los
propietarios de equipos a reciclar sus productos de TI. Se puede encontrar
informacin sobre las ofertas de reciclado de productos de IBM en el sitio web de
IBM http://www.ibm.com/ibm/environment/products/prp.shtml.
Notice: This mark applies only to countries within the European Union (EU) and
Norway.
This appliance is labeled in accordance with European Directive 2002/96/EC

concerning waste electrical and electronic equipment (WEEE). The Directive
determines the framework for the return and recycling of used appliances as
applicable throughout the European Union. This label is applied to various products
to indicate that the product is not to be thrown away, but rather reclaimed upon end
of life per this Directive.
Appendix. Notices 51
Remarque : Cette marque sapplique uniquement aux pays de lUnion Europenne
et la Norvge.
Letiquette du systme respecte la Directive europenne 2002/96/EC en matire de

Dchets des Equipements Electriques et Electroniques (DEEE), qui dtermine les
dispositions de retour et de recyclage applicables aux systmes utiliss travers
lUnion europenne. Conformment la directive, ladite tiquette prcise que le
produit sur lequel elle est appose ne doit pas tre jet mais tre rcupr en fin
de vie.
In accordance with the European WEEE Directive, electrical and electronic

equipment (EEE) is to be collected separately and to be reused, recycled, or
recovered at end of life. Users of EEE with the WEEE marking per Annex IV of the
WEEE Directive, as shown above, must not dispose of end of life EEE as unsorted
municipal waste, but use the collection framework available to customers for the
return, recycling, and recovery of WEEE. Customer participation is important to
minimize any potential effects of EEE on the environment and human health due to
the potential presence of hazardous substances in EEE. For proper collection and
treatment, contact your local IBM representative.
Battery return program

This product may contain a sealed lead acid, nickel cadmium, nickel metal hydride,
lithium, or lithium ion battery. Consult your user manual or service manual for
specific battery information. The battery must be recycled or disposed of properly.
Recycling facilities may not be available in your area. For information on disposal of
batteries outside the United States, go to http://www.ibm.com/ibm/environment/
products/batteryrecycle.shtml or contact your local waste disposal facility.
In the United States, IBM has established a return process for reuse, recycling, or
proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal hydride,
and battery packs from IBM equipment. For information on proper disposal of these
batteries, contact IBM at 1-800-426-4333. Have the IBM part number listed on the
battery available prior to your call.
For Taiwan: Please recycle batteries.
For the European Union:

For California: Perchlorate material special handling may apply. See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate/.
The foregoing notice is provided in accordance with California Code of Regulations

Title 22, Division 4.5 Chapter 33. Best Management Practices for Perchlorate
Materials. This product/part may include a lithium manganese dioxide battery which
contains a perchlorate substance.
Electronic emission notices
Federal Communications Commission (FCC) statement

Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the
interference at his own expense.
Properly shielded and grounded cables and connectors must be used in order to
meet FCC emission limits. IBM is not responsible for any radio or television
interference caused by using other than recommended cables and connectors or by
unauthorized changes or modifications to this equipment. Unauthorized changes or
modifications could void the users authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Industry Canada Class A emission compliance statement

This Class A digital apparatus complies with Canadian ICES-003.
Avis de conformit la rglementation dIndustrie Canada
Cet appareil numrique de la classe A est conforme la norme NMB-003 du

Canada.
Australia and New Zealand Class A statement

Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
United Kingdom telecommunications safety requirement

Notice to Customers
This apparatus is approved under approval number NS/G/1234/J/100003 for indirect

connection to public telecommunication systems in the United Kingdom.
Appendix. Notices 53
European Union EMC Directive conformance statement
This product is in conformity with the protection requirements of EU Council
Directive 89/336/EEC on the approximation of the laws of the Member States
relating to electromagnetic compatibility. IBM cannot accept responsibility for any
failure to satisfy the protection requirements resulting from a nonrecommended
modification of the product, including the fitting of non-IBM option cards.
This product has been tested and found to comply with the limits for Class A
Information Technology Equipment according to CISPR 22/European Standard EN
55022. The limits for Class A equipment were derived for commercial and industrial
environments to provide reasonable protection against interference with licensed
communication equipment.
Attention: This is a Class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take adequate
measures.
Taiwanese Class A warning statement
Chinese Class A warning statement
Japanese Voluntary Control Council for Interference (VCCI) statement

Index
A cover (continued)
removing 18
adapter
installing 19
PCI Express bus 19
administrator password 39, 42
D
attention notices 2 danger statements 2
device drivers 6
DIMMs
B installing 29
removing 29
baseboard management controller utility programs 46
supported 3
bays 3
drives 3, 4
bypassing an unknown password 42
DVD drive
See CD/DVD drive
C
caution statements 2
CD drive
E
electrical input 3
See CD/DVD drive
electronic emission Class A notice 53
CD-eject button 7
environment 3
CD/DVD drive
Ethernet
activity LED 8
connector 8
replacing 26
controller 4
specification 3
type 3
Class A electronic emission notice 53
speed indicator 8
command-line interface
speed LED 8
commands
transmit/receive activity LED 8
connect 47
expansion bays 3
identify 47
expansion slots 3
power 47
reboot 47
sel 47
sysinfo 47
F
using 47 FCC Class A notice 53
configuration features 3
Configuration/Setup Utility 38 and specifications 3
with ServerGuide 37 RAS 5
Configuration/Setup Utility program 38 ServerGuide 36
configuring firmware code, updating 46
hot-swap SAS or SATA devices 43 forgotten password, bypassing 42
SAS/SATA controller 43
connectors 8
external 14 H
front 33 hard disk drive
internal 12 activity LED 7
optional device, on system board 16 hot-swap SATA 25
rear 33 installing 24
controller removing 25
Ethernet SAS 25
configuring 47 SCSI
network support 4 See SAS
type 3 simple-swap SATA 24
hard disk drive 3 heat output 3
SAS 3 humidity 3
SATA 3
video 3
cover
installing 33

I NOS installation (continued)
without ServerGuide 37
IBM Director 4, 5, 47
notes 2
important notices 2
notes, important 50
installation order, memory modules 28
notices
installing
electronic emission 53
adapter 19
FCC, Class A 53
cover 33
notices and statements 2
DIMMs 28
hard disk drive 24
memory modules 28
SATA RAID kit 30
O
integrated online publications 2
baseboard management controller utility optical drive
programs 46 See CD/DVD drive
controllers 3 order of installation, memory modules 28
functions 3
internal connectors 12
P
password
J administrator 42
jumper, clear CMOS (password override) 42 clear CMOS jumper 42
jumpers 13 override 42
power-on 41
resetting 42
K power
requirement 3
keyboard connector 8
supply 3
power-control
button 7
L button shield 7
LED power-cord connector 8
cd drive activity 8 power-on LED 7
Ethernet speed 8 power-on password 39
Ethernet transmit/receive activity 8 publications 1
hard disk drive activity 7
locator 7
power-on 7
system error 7
R
RAS features 5
LEDs
reset button 7
front 7
resetting passwords 42
rear 8
riser card
local area network (LAN) 4
connector location 12
locator LED 7
location 21
slots 16
M
memory
capacity 4
S
SAS
specifications 3
hot-swap drives 3
memory module
hot-swap models 3
order of installation 28
SATA
specifications 28
hot-swap 3
microprocessor
simple-swap 3
type 3
serial connector 8
mouse connector 8
ServeRAID 4
ServerGuide
CD 4
N features 36
noise emissions 3 NOS installation 37
NOS installation setup 37
with ServerGuide 37

ServerGuide (continued)
using 36
V
video connector 8
setting clear CMOS (password override) jumper 42
video controller 3
simple-swap Serial ATA hard disk drive 24, 25
size 3
slot locations
adapter 16 W
PCI Express 16 weight 3
slots 3
SMBridge management utility program 44
installing 44
specifications 3
standby 5, 15
Standby mode 9
statements and notices 2
supervisor password
See administrator password
switches and jumpers 13
system board
internal connectors 12
jumper blocks 13
LEDs 15
optional-device connectors 16
switches and jumpers 13
system-error LED 7
and system-event log 40
system-event log
about 40
clearing 40
systems management 5
systems-management connector 8
T
temperature 3
trademarks 49
turning off the server 9
turning on the server 9
U
United States electronic emission Class A notice 53
United States FCC Class A notice 53
unknown password, bypassing 42
UpdateXpress 6
updating the firmware code 46
USB connector 7, 8
user password 42
See power-on password
using
baseboard management controller utility
programs 46
command-line interface 47
utility program
baseboard management 44
Configuration/Setup 38
LSI Logic Configuration Utility program 43
SAS configuration 43
SMBridge management 44
Index 57

Part Number: 42C5005
Printed in USA
(1P) P/N: 42C5005

x3250 m1 Guide

Uploaded by

Copyright:

Available Formats

x3250 m1 Guide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

x3250 m1 Guide

Uploaded by

Copyright:

Available Formats

IBM System x3250 Types 4364 and 4365

IBM System x3250 Types 4364 and 4365

Third Edition (January 2007)

Chapter 1. The System x3250 Types 4364 and 4365 server . . . . . . . . 1

Chapter 2. Installing optional devices . . . . . . . . . . . . . . . . 11

Chapter 3. Configuring the server . . . . . . . . . . . . . . . . . 35

Copyright IBM Corp. 2007 iii

iv IBM System x3250 Types 4364 and 4365: Users Guide

Antes de instalar este produto, leia as Informaes de Segurana.

Pred instalac tohoto produktu si prectete prrucku bezpecnostnch instrukc.

Ls sikkerhedsforskrifterne, fr du installerer dette produkt.

Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.

Avant dinstaller ce produit, lisez les consignes de scurit.

Vor der Installation dieses Produkts die Sicherheitshinweise lesen.

Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.

Les sikkerhetsinformasjonen (Safety Information) fr du installerer dette produktet.

Antes de instalar este produto, leia as Informaes sobre Segurana.

Copyright IBM Corp. 2007 v

Ls skerhetsinformationen innan du installerar den hr produkten.

vi IBM System x3250 Types 4364 and 4365: Users Guide

For example, if a caution statement is labeled Statement 1, translations for that

Electrical current from power, telephone, and communication cables is

To avoid a shock hazard:

1. Turn everything OFF. 1. Turn everything OFF.

Dispose of the battery as required by local ordinances or regulations.

Class 1 Laser Product

18 kg (39.7 lb) 32 kg (70.5 lb) 55 kg (121.2 lb)

x IBM System x3250 Types 4364 and 4365: Users Guide

This server is suitable for use on an IT power-distribution system whose maximum

Performance, ease of use, reliability, and expansion capabilities were key

The server contains IBM X-Architecture technologies, which help increase

Depending on the server model, additional documentation might be included on the

Copyright IBM Corp. 2007 1

Notices and statements in this document

The following notices and statements are used in this document:

2 IBM System x3250 Types 4364 and 4365: Users Guide

Chapter 1. The System x3250 Types 4364 and 4365 server 3

4 IBM System x3250 Types 4364 and 4365: Users Guide

Reliability, availability, and serviceability features

The server has the following RAS features:

Chapter 1. The System x3250 Types 4364 and 4365 server 5

IBM Director provides a comprehensive entry-level workgroup hardware manager. It

The UpdateXpress program

6 IBM System x3250 Types 4364 and 4365: Users Guide

USB connectors: Connect a USB device to either of these connectors.

CD-eject button: Press this button to release a CD from the CD drive.

Chapter 1. The System x3250 Types 4364 and 4365 server 7

Ethernet 1 transmit / receive Ethernet 2 speed LED

Ethernet transmit/receive activity LED: This LED is on each Ethernet connector.

Systems-management USB 3 connector Serial connector

Power-cord connector: Connect the power cord to this connector.

Keyboard connector: Connect a PS/2 keyboard to this connector.

Mouse connector: Connect a mouse or other PS/2 device to this connector.

Serial connector: Connect a 9-pin serial device to this connector.

Video connector: Connect a monitor to this connector.

Ethernet connector: Use either of these connectors to connect the server to a

USB connector: Connect a USB device to either of these connectors.

Systems-management connector: Connect the server to a network for

8 IBM System x3250 Types 4364 and 4365: Users Guide