Scribd
Upload
218 views5 pages

Aisc Asd-89 Example 002

The document summarizes an example from the AISC ASD-89 design code checking the column design features for a frame under compression. It shows: 1) The frame geometry, properties, and two point loads of 560 kips applied to each column are tested against the code. 2) The results match the independent calculations for compactness, design axial stress of 15.86 ksi, and allowable axial stress of 16.47 ksi within 0.00% difference. 3) The computer file and hand calculations confirm the section is compact and the member compression capacity is satisfied according to the AISC ASD-89 code.

Uploaded by

Antonius Ajalah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
218 views5 pages

Aisc Asd-89 Example 002

The document summarizes an example from the AISC ASD-89 design code checking the column design features for a frame under compression. It shows: 1) The frame geometry, properties, and two point loads of 560 kips applied to each column are tested against the code. 2) The results match the independent calculations for compactness, design axial stress of 15.86 ksi, and allowable axial stress of 16.47 ksi within 0.00% difference. 3) The computer file and hand calculations confirm the section is compact and the member compression capacity is satisfied according to the AISC ASD-89 code.

Uploaded by

Antonius Ajalah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Software Verification

PROGRAM NAME: SAP2000


REVISION NO.: 0

AISC ASD-89 Example 002

WIDE FLANGE MEMBER UNDER COMPRESSION

EXAMPLE DESCRIPTION
The column design features for the AISC ASD-89 code are checked for the frame
shown below. This frame is presented in the Allowable Stress Design Manual of
Steel Construction, Ninth Edition, 1989, Example 3, Pages 3-6 and 3-7. The
column K factors were overwritten to a value of 2.13 to match the example. The
transverse direction was assumed to be continuously supported. Two point loads
of 560 kips are applied at the tops of each column. The ratio of allow axial stress,
Fa, to the actual, fa, was checked and compared to the referenced design code.

GEOMETRY, PROPERTIES AND LOADING

TECHNICAL FEATURES TESTED


Section compactness check (compression)
Member compression capacity

AISC ASD-89 Example 002 - 1


Software Verification
PROGRAM NAME: SAP2000
REVISION NO.: 0

RESULTS COMPARISON

Independent results are taken from Allowable Stress Design Manual of Steel
Construction, Ninth Edition, 1989, Example 3, Pages 3-6 and 3-7.

Percent
Output Parameter SAP2000 Independent Difference
Compactness Compact Compact 0.00%

Design Axial Stress, fa (ksi) 15.86 15.86 0.00%


Allowable Axial Stress, 16.47 16.47 0.00%
Fa (ksi)

COMPUTER FILE: AISC ASD-89 EX002

CONCLUSION
The results show an exact comparison with the independent results.

AISC ASD-89 Example 002 - 2


Software Verification
PROGRAM NAME: SAP2000
REVISION NO.: 0

HAND CALCULATION

Properties:
Material: A36 Steel
E = 29,000 ksi, Fy = 36 ksi
Section: W12x120:
bf = 12.32 in, tf = 1.105 in, d =13.12 in, tw=0.71 in
A = 35.3 in2
rx=5.5056 in
Member:
K = 2.13
L = 15 ft
Loadings:
P = 560 kips
Design Axial Stress:
P 560
f=
a =
A 35.3
f a = 15.86 ksi

Compactness:
Localized Buckling for Flange:
bf 12.32

= = = 5.575
2t f 2 1.105

65 65
p
= = = 10.83
Fy 36

< p , No localized flange buckling


Flange is Compact.

AISC ASD-89 Example 002 - 3


Software Verification
PROGRAM NAME: SAP2000
REVISION NO.: 0

Localized Buckling for Web:


f a 15.86
= = 0.44
Fy 36

d 13.12

= = = 18.48
tw 0.71
fa
Since = 0.44 > 0.16
Fy

257 257
p
= = = 42.83
Fy 36

< p , No localized web buckling


Web is Compact.

Section is Compact.

Member Compression Capacity


KL x 2.13 (15 12 )
= = 69.638
rx 5.5056

22 E 22 29000
=Cc = = 126.099
Fy 36

KL x
rx 69.638
= = 0.552
Cc 126.099
KL x
< Cc
rx

AISC ASD-89 Example 002 - 4


Software Verification
PROGRAM NAME: SAP2000
REVISION NO.: 0

1 KL x rx
2

1.0 Fy
2 Cc
Fa = 3
5 3 KL x rx 1 KL x rx
+
3 8 C c 8 Cc
2
1.0 (0.552 ) 36
1

Fa =
2
+ (0.552 ) (0.552 )
5 3 1 3

3 8 8

Fa = 16.47 ksi

AISC ASD-89 Example 002 - 5

You might also like