Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

General Description Features

The AP3842C/3C/4C/5C are high performance fixed Low Start-up Current: 50A
frequency current-mode PWM controller series. Robust VREF Line/Load Regulation
Low Line Regulation : 4mV
These integrated circuits are optimized for off-line and Low Load Regulation : 4mV
DC-DC converter applications with minimum external
High Stability of Reference Voltage over a Full
components. They feature under-voltage lockout
(UVLO) circuit with low start-up current, trimmed Temperature Range: 0.2mV/ oC
oscillator for precise duty cycle control, current sense Operating Frequency up to 500KHz
comparator providing maximum current limiting and a High PWM Frequency Stability over a Full Tem-
totem pole output stage for increasing output current. perature Range: 2.5%
In addition, these ICs also feature accurate protection High PWM Frequency Stability under a Full Sup-
against over-temperature, over-current and maximal ply Voltage Range: 0.2%
output power. Accurate Over-temperature Protection with Hys-
teresis
The AP3842C and AP3844C have UVLO thresholds UVLO with Hysteresis
of 16V(on) and 10V(off); The corresponding thresh-
olds for AP3843C and AP3845C are 8.4 V(on) and
7.6V(off).
Applications

The AP3842C and AP3843C can operate approaching Off-line Converter

100% duty cycle; AP3844C and AP3845C can operate DC-DC Converter
from zero to 50% duty cycle. Voltage Adapter
CRT Monitor Power Supply
These ICs are available in SOIC-8 and DIP-8 pack- Desktop Power Supply
ages.
DVD/STB Power Supply

SOIC-8 DIP-8

Figure 1. Package Types of AP3842C/3C/4C/5C

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

1
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Pin Configuration

P/M Package
(DIP-8/SOIC-8)

COMP 1 8 VREF
VFB 2 7 VCC
ISENSE 3 6 OUTPUT
RT/CT 4 5 GND

Figure 2. Pin Configuration of AP3842C/3C/4C/5C (Top View)

Pin Description

Pin Number Pin Name Function

1 COMP This pin is the Error Amplifier output and is made available for loop compensation.
2 VFB The inverting input of the Error Amplifier. It is normally connected to the switching
power supply output through a resistor divider.
3 ISENSE A voltage proportional to inductor current is connected to this input. The PWM uses
this information to terminate the output switch conduction.
4 RT/CT The Oscillator frequency and maximum output duty cycle are programmed by con-
necting resistor RT to VREF and capacitor CT to ground. Operation to 500 kHz is possi-
ble.
5 GND The combined control circuitry and power ground.
6 OUTPUT This output directly drives the gate of a power MOSFET. Peak currents up to 1.0 A are
sourced and sunk by this pin.
7 VCC The positive supply of the control IC.
8 VREF This is the reference output. It provides charging current for capacitor CT through
resistor RT.

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

2
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Functional Block Diagram

VCC 7
34V UVLO
5V
5
S/R
REF 8 VREF
GND

2.50V INTERNAL
BIAS

VREF
GOOD
LOGIC
6
OUTPUT
4 OSC T
RT/CT
OVER TEMP (Note)
PROTECT

ERROR
AMP S
2R
2
VFB R PWN
1 1V LATCH
R
COMP CURRENT
3 SENSE Note: Toggle flip-flop used
ISENSE COMPARATOR for 3844C/45C only

Figure 3. Functional Block Diagram of AP3842C/3C/4C/5C

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

3
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Ordering Information

AP384XC -

Circuit Type E1: Lead Free

Blank: Tin Lead
TR: Tape and Reel
Package
Blank: Tube
M: SOIC-8
P: DIP-8

Tempera- Part Number Marking ID Packing

Package
ture Range Tin Lead Lead Free Tin Lead Lead Free Type

AP3842/3/4/5CM AP3842/3/4/5CM-E1 3842/3/4/5CM 3842/3/4/5CM-E1 Tube

SOIC-8 -40 to 85oC
AP3842/3/4/5CMTR AP3842/3/4/5CMTR-E1 3842/3/4/5CM 3842/3/4/5CM-E1 Tape & Reel
DIP-8 -40 to 85oC AP3842/3/4/5CP AP3842/3/4/5CP-E1 AP3842/3/4/5CP AP3842/3/4/5CP-E1 Tube

BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant.

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

4
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Absolute Maximum Ratings (Note 1, 2)

Parameter Symbol Value Unit

Supply Voltage VCC 30 V

Output Current IO 1 A

Analog Inputs V(ANA) -0.3 to 6.3 V

Error Amp Output Sink Current ISINK(E.A) 10 mA

Power Dissipation at TA< 25 oC (DIP-8) PD (Note 3) 1000 mW

Power Dissipation at TA<25 oC (SOIC-8) PD (Note 3) 460 mW

Junction Operating Temperature TJ -40 to 150 oC

DIP-8 140 oC/W

Thermal Resistance (Junction to Ambient) RJA
SOIC-8 160 oC/W

Storage Temperature Range TSTG -65 to 150 oC

Lead Temperature (Soldering, 10sec) TLEAD +300 oC

ESD (Machine Mode) 250 V

Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the
device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indi-
cated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended
periods may affect device reliability.
Note 2: All voltages are with respect to pin 5 and all currents are positive into specified terminal.
Note 3: Board thickness 1.6mm, board dimension 90mm x 90mm.

Recommended Operating Conditions

Parameter Symbol Min Max Unit
Oscillation Frequency f 500 KHz
Ambient Temperature TA -40 85 o
C

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

5
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Electrical Characteristics
(VCC=15V, RT=10k CT=3.3nF, TA= -40 to 85oC, unless otherwise specified.)
Parameter Symbol Conditions Min Typ Max Unit
REFERENCE SECTION
Reference Output Voltage VREF TJ=25oC, IREF=1mA 4.90 5.00 5.10 V
Total Output Variation Line, Load, Temp. 4.82 5.18 V
Line Regulation VREF 12V VCC 25V 4 15 mV
Load Regulation VREF 1mA IREF 20mA 4 15 mV
Short Circuit Output Current ISC TA=25oC -100 -180 mA
Temperature Stability 0.2 0.4 mV/oC
OSCILLATOR SECTION
Oscillation Frequency f TJ=25oC 47 52 57 KHz
Oscillator Amplitude VOSC Pin 4, peak to peak (Note 6) 1.7 V
Temperature Stability (Note 6) 2.5 %
Voltage Stability 12V VCC 25V 0.2 1 %
Discharge Current Vpin 4 =2V(Note 7) 8.5 9.5 10.5 mA
ERROR AMPLIFIER SECTION
Input Voltage VI Vpin 1=2.5V 2.45 2.50 2.55 V
Output Sink Current ISINK Vpin1=1.1V 5 8 mA
Output Source Current ISOURCE Vpin1=5V -0.5 -0.8 mA
High Output Voltage VOH RL=15k to GND 5 7 V
Low Output Voltage VOL RL=15k to pin 8 0.7 1.1 V
Voltage Gain 2V VO 4V 65 90 dB
Power Supply Rejection Ratio PSRR 12V VCC 25V 60 70 dB
CURRENT SENSE SECTION
Maximum Input Signal VI(MAX) Vpin1=5V(Note 4) 0.9 1 1.1 V
Gain GV (Note 4, 5) 2.85 3 3.15 V/V
Power Supply Rejection Ratio PSRR 12V VCC 25V (Note 4, 6) 70 dB
Delay to Output Vpin3 = 0 to 2V (Note 6) 150 300 ns
Input Bias Current IBIAS -3 -10 A
OUTPUT SECTION
Low Output Voltage ISINK = 20mA 0.1 0.4 V
VOL
ISINK = 200mA 1.4 2.2 V
High Output Voltage ISOURCE = 20mA 13 14 V
VOH
ISOURCE = 200mA 12 13 V
Rise Time tR o
TJ=25 C, CL=1nF (Note 6) 50 150 ns
Fall Time tF TJ =25oC, CL=1nF (Note 6) 50 150 ns

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

6
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Electrical Characteristics (Continued)
Parameter Symbol Conditions Min Typ Max Unit
UNDER -VOLTAGE LOCKOUT SECTION
Start Threshold AP3842C/AP3844C 15 16 17 V
VTH(ST)
AP3843C/AP3845C 7.8 8.4 9.0 V
Min. Operation Voltage VOPR AP3842C/AP3844C 8.5 10.0 11.5 V
(After Turn On) (Min.) AP3843C/AP3845C 7.0 7.6 8.2 V
PWM SECTION
D(Max.) AP3842C/AP3843C 95 97 100 %
Max. Duty Cycle
D(Max.) AP3844C/AP3845C 46 48 50 %
Min. Duty Cycle D(Min.) 0 %
TOTAL STANDBY CURRENT SECTION
Start-Up Current IST 50 80 A
Operating Supply Current ICC(OPR) Vpin3=Vpin2=0V 8 12 mA
Zener Voltage VZ ICC=25mA 30 34 V
OVER-TEMPERATURE PROTECT SECTION
Shutdown Temperature TSHUT (Note 6) 155 oC

Temperature Hysteresis THYS (Note 6) 25 oC

Note 4: Parameters are tested at trip point of latch with Vpin2 = 0.

Note 5: Here gain is defined as:
VPin 1
A= , 0 Vpin3 0.8V
VPin 3
Note 6: These parameters, although guaranteed, are not 100% tested in production.
Note 7: This parameter is measured with RT=10k to VREF, it contributes 0.3mA of current to the measured value.
So the total current flowing into the CT pin will be 0.3mA higher than the measured value approximately.

VREF
RT
4.7k 2N2222 AP384XC
A VCC
1 COMP VREF 8

100k
1k
ERROR AMP 2 VFB VCC 7
ADJUST 1K
0.1F
5k 1W
3 ISENSE OUTPUT 6
4.7k ISENSE OUTPUT
ADJUST
0.1F
4 RT/CT GND 5

GND
CT

Figure 4. Basic Test Circuit

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

7
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

ELectrical Characteristics (Continued)
Figure 4 is the basic test circuit for AP384XC. In testing, the high peak currents associated with capacitive loads
necessitate careful grounding techniques. Timing and bypass capacitors should be connected close to pin 5 in a
single point ground. The transistor and 5k potentiometer are used to sample the oscillator waveform and apply an
adjustable ramp to pin 3.

Typical Performance Characteristics

Figure 5. Oscillator Dead Time vs. Timing Capacitor Figure 6. Timing Resistor vs. Frequency

5.015
4.0
VCC=15V, IO=1mA
5.010 3.5 o
VCC=15V, TA=25 C
Saturation Voltage (V)

3.0
Reference Voltage (V)

5.005

2.5
5.000
2.0

4.995 1.5

1.0
4.990
0.5
4.985
0.0

4.980 -0.5
-40 -20 0 20 40 60 80 100 120 0 50 100 150 200 250 300 350 400 450 500 550 600
o
Ambient Temperature ( C)
Output Sink Current (mA)

Figure 7. Reference Voltage vs. Ambient Temperature Figure 8. Output Saturation Characteristics

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

8
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Typical Performance Characteristics (Continued)

90 60

80

70 o
VCC=15V, TA=25 C 50

Start-up Current (A)

Voltage Gain (dB)

60

50
40
40

30

30
20

10

0 20
10 100 1k 10k 100k 1M -40 -20 0 20 40 60 80 100 120
o
Frequency (Hz) Ambient Temperature ( C)

Figure 9. Error Amplifier Open-Loop Frequency Response Figure 10. Start-up Current vs. Ambient Temperature

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

9
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Typical Application

NTC Bridge Diode

1N4007*4 R19
10
C2 R3
+ 0.01 39k C15
R2 C14 600V 2.2n
2W L3 C10 C11 R20 Z2
J1 1M/ 100/400V
T 10 1000 1 2K SA12A
0.25W
AC 90 to 265V D1
Byv26e D3 + +
C1 47 R4 10 8TQ100 C9
2200
+

D2
1N4001 J2
12V/5A

C3
0.1
7 Vcc
V VREF 8
CC
R12
100 R5 C4
10k 3.3n
2 VFB RT/CT 4 C8
C5 C15 0.22
220p 100p R6 C6
20 2200p/600V R15 R16
1 COMP OUTPUT 6
100 8.2k
R14
130k R7 Q1
1k IRF830
5 GND ISENSE 3
C7 U3 W1 R18
680p AZ431 1k 3.9k
U1 R10
R13 AP3842C/3C/4C/5C Z1 R9 0.51/1W
15k 1N5819 7.5k
R17
2k
R11
820 U2 PC817

Figure 11. Typical Application of AP3842C/3C/4C/5C

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

10
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Mechanical Dimensions

SOIC-8 Unit: mm(inch)

4.800(0.189)
0.320(0.013)
5.000(0.197) 1.350(0.053)
7
1.750(0.069)
8

7 8
0.675(0.027)
D
0.725(0.029) 5.800(0.228)
1.270(0.050) 6.200(0.244)
TYP
D
20:1
0.100(0.004) 0.800(0.031)
R0.150(0.006)

0.300(0.012)
0.200(0.008)

0
8
1.000(0.039)
3.800(0.150)
4.000(0.157)

1
0.330(0.013) 5
0.510(0.020)
0.900(0.035) R0.150(0.006)

0.190(0.007)
0.250(0.010)

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

11
 Data Sheet

CURRENT MODE PWM CONTROLLER AP384XC

Mechanical Dimensions (Continued)

DIP-8 Unit: mm(inch)

0.700(0.028)
7.620(0.300)TYP
1.524(0.060) TYP
5
6 6

3.200(0.126)
3.710(0.146) 3.600(0.142)
4.310(0.170) 4
4

0.510(0.020)MIN
3.000(0.118)
3.600(0.142)

0.204(0.008)
0.254(0.010)TYP 0.360(0.014)
0.360(0.014) 2.540(0.100) TYP 8.200(0.323)
0.560(0.022) 9.400(0.370)
0.130(0.005)MIN

6.200(0.244)
R0.750(0.030) 6.600(0.260)

3.000(0.118)
Depth
0.100(0.004)
0.200(0.008)
9.000(0.354)
9.400(0.370)

Sep. 2006 Rev. 1. 1 BCD Semiconductor Manufacturing Limited

12
 http://www.bcdsemi.com

IMPORTANT NOTICE

BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifi-
cations herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any
particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use
of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or
other rights nor the rights of others.

MAIN SITE
BCD Semiconductor Manufacturing Limited BCD Semiconductor Manufacturing Limited
- Wafer Fab - IC Design Group
Shanghai SIM-BCD Semiconductor Manufacturing Limited Advanced Analog Circuits (Shanghai) Corporation
800, Yi Shan Road, Shanghai 200233, China 8F, Zone B, 900, Yi Shan Road, Shanghai 200233, China
Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 Tel: +86-21-6495 9539, Fax: +86-21-6485 9673

REGIONAL SALES OFFICE

Shenzhen Office Taiwan Office USA Office
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. Shenzhen Office BCD Semiconductor (Taiwan) Company Limited BCD Semiconductor Corporation
Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, 3170 De La Cruz Blvd., Suite 105,
Room E, 5F, Noble Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China Taiwan Santa Clara,
Tel: +86-755-8826 7951, Fax: +86-755-8826 7865 Tel: +886-2-2656 2808, Fax: +886-2-2656 2806 CA 95054-2411, U.S.A