Process controller

CODIX 553 with 2 limit values

Your benefit Input range

Programmable input characteristic curve 0 ... 20 mA, 4 ... 20 mA; 0 ...10 V
with up to 24 control points 2 ... 10 V; +10 V
Display-Hold or reset input for the limit Outputs
values 2 limit values with programmable hysteresis
Very big keys for use with gloves and programmable signal behaviour, relays
Input for key-look with change-over contact or optocoupler
very bright display More advantages
erial Auxiliary power supply output for
able with s measuring transducer/sensor
avail -up
Now e and set optional serial interface
fa c ol!
inter e EzContr
w ar
soft
Technical data
Miscellaneous Data Weight approx. 220 g
Display 5 digit red LED 14.2 mm high Protection IP 65 (front)
Display range 19999 ... 99999, with leading zeros suppression Ambient temperature 20 ... +65 C
Out of Range Indication Under-range uuuuu / Over-range ooooo Storage temperature 40 ... +85 C
Data storage EEPROM, 1 Million storage cycles or 10 Years Digital inputs
Test voltages EN 61010 Part 1 ; overvoltage category 2, level 2 Input MPI* Function of the inputs depending on set up
EMC Interference emissions EN 50081-2 / 1. Function Display-Hold to stop the instantaneous value
EN 55011 Class B 2. Function Reset Reset the alarm value
Interference resistance EN 61000-6-2 Alarm Latch
AC power supply 90 ... 260 V AC/max. 6 VA
external fuse 100 mA/T Outputs
DC power supply 10 ... 30 V DC, max. 2 W, galvanically isolated Alarm 1/Alarm output 2
with inverse polarity protection Relay output with volt-free changeover contacts can be
external fuse 250 mA/T setup as normally closed or normally open
Mains Hum Filter digital filter 50 Hz or 60 Hz, programmable Switching voltage 250 V AC/300 V DC
Measurement ranges Switching current max. 3 A AC/DC, min. 30 mA DC
Current input (DC) Ranges 0 ... 20 mA, 4 ... 20 mA Switching power 2000 VA / 50
Resolution 2 A or NPN-ooptocoupler with open collector and open emitter
Voltage drop max. 2 V bei 20 mA Switching power 30 V DC/15 mA
Max. current 50 mA Auxiliary power supply output for measuring transducer/sensor
Voltage input(DC) Ranges 0 ... 10 V, 2 ... 10 V, 10 V AC models voltage output 10 V DC 2%, 30 mA and
Resolution 1 mV voltage output 24 V DC 15%, 50 mA
Input resitance > 2 M DC models only voltage output 10 V DC 2%, 30 mA
Max. voltage 30 V Interface
Measuring speed approx. 2 measurements/s Available options RS232, RS485, RS422
Linearity < 0,1% 1 Digit for the whole measuring Baud rate 600, 1200, 2400, 4800, 9600, 19 200 programmable
range at an ambient temperature of 20C Address
*MPI: Multi Purpose Input 00 ... 99 programmable
Zero calibration automatic
Temperature drift 100 ppm/K

Dimensions:

Panel cut-out

26 www.kuebler.com
Process controller

Connections:
Rear side view Power supply and alarm outputs
Measuring- and Relay output 7
X2 control inputs as OUT 2 OUT 1 8
X1
well as auxiliary 1 2 3 4 5 6 7 8
signals
X1

Power supply and

X3 Optocoupler output 7
limit outputs
X1 OUT 2 OUT 1 8

Interface 1 2 3 4 5 6 7 8

DC version AC version
Current measurement
7 10 ... 30 V DC 90 ... 260 V AC (N~)
8 GND4 (0 V DC) 90 ... 260 V AC (L~)

+ -
X2
1 2 3 4 5 6 7 8 9 10 11

1 Current input (I)

0 ... 20 mA / 4 ... 20 mA
2 GND1 (Analog) Control inputs and auxiliary power supply (Uout)

9 9 GND3 (for Uout)

Voltage measurement 10 10 Uout +10 V/30 mA
1
11
1 11 Uout +24 V/50 mA only for power supply
1
X2 90 ... 260 V AC
X2 1 2 3 4 5 6 7 8 9 10 11 8 MP-Input "Reset-Alarm-Latch/
- +
1 2 3 4 5 6 7 8 9 10 11 Display-Hold
1 Alternatively connect directly 7 GND2 (KEY/MPI)
2 GND1 (Analog) to DC supply (galvanic 6 Keypad lock-out "Key"
3 Voltage input (U) separation of control and
0 ... 10 V, 2 ... 10 V, -10 ... +10 V measurement inputs)

Interface Application: Serial interface

Level measurement For data transmission and documentation
X3 1 2 3 4 5 Flow measurement Connection for programmable logic
RS232 RS485 RS422 Pressure measurement controllers
1 GND Revolution measurement Programming via PC
2 RxD DO+/RI+ RI+
3 TxD DO/RI RI
4 DO+
5 DO

Delivery includes: Order code:

Process display 6.553.01X.X0X
Screw terminal, 8-pole, RM 5.08 Interface
Screw terminal, 11-pole, RM 3.81 0 = without interface
Screw terminal, 5-pole, RM 3.81(*) 5 = RS232
Clamping bracket 6 = RS422
Gasket 7 = RS485
Multilingual operating instructions Supply voltage
1 set of self-adhesive symbols 0 = 90 .. 260 V AC
* only with the interface option 3 = 10 .. 30 V DC
Alarm output
0 = relay
1 = optocoupler
www.kuebler.com 27