ECDIS

RESOLUTION MSC.
232(82)
(adopted on 5 December 2006)
ADOPTION OF THE REVISED PERFORMANCE
STANDARDS FOR ELECTRONIC CHART DISPLAY AND
INFORMATION SYSTEMS (ECDIS)
RESOLUTION MSC.232(82)
ADOPTION OF THE REVISED PERFORMANCE MSC 82/24/Add.2
ANNEX 24
ADOPTION OF THE REVISED PERFORMANCE STANDARDS FOR

ELECTRONIC CHART DISPLAY AND INFORMATION SYSTEMS (ECDIS)
THE MARITIME SAFETY COMMITTEE,
RECALLING Article 28(b) of the Convention on the International Maritime Organization

concerning the functions of the Committee,
RECALLING ALSO resolution A.886(21), by which the Assembly resolved that the
function of adopting performance standards and technical specifications, as well as amendments
thereto shall be performed by the Maritime Safety Committee and/or the Marine Environment
Protection Committee, as appropriate, on behalf of the Organization,
RECALLING ALSO regulations V/19 and V/27 of the International Convention for the
Safety of Life at Sea (SOLAS), 1974, which requires all ships to carry adequate and up-to-date
charts, sailing directions, lists of lights, notices to mariners, tide tables and all other nautical
publications necessary for the intended voyage,
NOTING that the up-to-date charts required by SOLAS regulations V/19 and V/27 can be
provided and displayed electronically on board ships by electronic chart display and information
systems (ECDIS), and that the other nautical publications required by regulation V/27 may also
be so provided and displayed,
RECOGNIZING the need to improve the previously adopted, by resolution A.817(19), as

amended, performance standards for ECDIS in order to ensure the operational reliability of such
equipment and taking into account the technological progress and experience gained,
HAVING CONSIDERED the recommendation made by the Sub-Committee on Safety of

Navigation, at its fifty-second session,
1. ADOPTS the Revised performance standards for electronic chart display and information
systems (ECDIS), set out in the Annex to the present resolution;
2. RECOMMENDS Governments ensure that ECDIS equipment:
(a) if installed on or after 1 January 2009, conform to performance standards not

inferior to those specified in the Annex to the present resolution; and
(b) if installed on or after 1 January 1996 but before 1 January 2009, conform to
performance standards not inferior to those specified in the Annex to
resolution A.817(19), as amended by resolutions MSC.64(67) and MSC.86(70).
I:\MSC\82\24-Add-2.doc
MSC 82/24/Add.2 ADOPTION OF THE REVISED PERFORMANCE
ANNEX 24 STANDARDS FOR ELECTRONIC CHART DISPLAY AND
Page 2
ANNEX
REVISED PERFORMANCE STANDARDS FOR ELECTRONIC CHART DISPLAY

AND INFORMATION SYSTEMS (ECDIS)
1 SCOPE OF ECDIS
1.1 The primary function of the ECDIS is to contribute to safe navigation.
1.2 ECDIS with adequate back-up arrangements may be accepted as complying with the
up-to-date charts required by regulations V/19 and V/27 of the 1974 SOLAS Convention,
as amended.
1.3 ECDIS should be capable of displaying all chart information necessary for safe and
efficient navigation originated by, and distributed on the authority of, government
authorized hydrographic offices.
1.4 ECDIS should facilitate simple and reliable updating of the electronic navigational chart.
1.5 ECDIS should reduce the navigational workload compared to using the paper chart.
It should enable the mariner to execute in a convenient and timely manner all route
planning, route monitoring and positioning currently performed on paper charts. It should
be capable of continuously plotting the ships position.
1.6 The ECDIS display may also be used for the display of radar, radar tracked target
information, AIS and other appropriate data layers to assist in route monitoring.
1.7 ECDIS should have at least the same reliability and availability of presentation as the
paper chart published by government authorized hydrographic offices.
1.8 ECDIS should provide appropriate alarms or indications with respect to the information
displayed or malfunction of the equipment (see appendix 5).
1.9 When the relevant chart information is not available in the appropriate form (see section 4),
some ECDIS equipment may operate in the Raster Chart Display System (RCDS) mode
as defined in appendix 7. RCDS mode of operation should conform to performance
standards not inferior to those set out in appendix 7.
2 APPLICATION OF THESE STANDARDS
2.1 These performance standards should apply to all ECDIS equipment carried on all ships,
as follows:
- dedicated standalone workstation.

- a multifunction workstation as part of an INS.
2.2 These performance standards apply to ECDIS mode of operation, ECDIS in RCDS mode
of operation as specified in appendix 7 and ECDIS backup arrangements as specified in
appendix 6.
STANDARDS FOR ELECTRONIC CHART DISPLAY AND ANNEX 24
Page 3
2.3 Requirements for structure and format of the chart data, encryption of chart data as well
as the presentation of chart data are within the scope of relevant IHO standards, including
those listed in appendix 1.
2.4 In addition to the general requirements set out in resolution A.694(17)*, the presentation
requirements set out in resolution MSC.191(79), ECDIS equipment should meet the
requirements of these standards and follow the relevant guidelines on ergonomic
principles adopted by the Organization1.
3 DEFINITIONS
For the purpose of these performance standards:
3.1 Electronic Chart Display and Information System (ECDIS) means a navigation
information system which with adequate back-up arrangements can be accepted as
complying with the up-to-date chart required by regulations V/19 and V/27 of the 1974
SOLAS Convention, as amended, by displaying selected information from a system
electronic navigational chart (SENC) with positional information from navigation sensors
to assist the mariner in route planning and route monitoring, and if required display
additional navigation-related information.
3.2 Electronic Navigational Chart (ENC) means the database, standardized as to content,
structure and format, issued for use with ECDIS by or on the authority of a Government,
authorized Hydrographic Office or other relevant government institution, and conform to
IHO standards. The ENC contains all the chart information necessary for safe navigation
and may contain supplementary information in addition to that contained in the paper
chart (e.g. sailing directions) which may be considered necessary for safe navigation.
3.3 System Electronic Navigational Chart (SENC) means a database, in the manufacturers
internal ECDIS format, resulting from the lossless transformation of the entire ENC
contents and its updates. It is this database that is accessed by ECDIS for the display
generation and other navigational functions, and is equivalent to an up-to-date paper
chart. The SENC may also contain information added by the mariner and information
from other sources.
3.4 Standard Display is the display mode intended to be used as a minimum during route
planning and route monitoring. The chart content is listed in appendix 2.
3.5 Display Base means the chart content as listed in appendix 2 and which cannot be
removed from the display. It is not intended to be sufficient for safe navigation.
3.6 Further information on ECDIS definitions may be found in IHO Hydrographic Dictionary
Special Publication S-32 (see appendix 1).
*
Refer to Publication IEC 60945.
1
MSC/Circ.982.
Page 4
MODULE A - DATABASE
4 PROVISION AND UPDATING OF CHART INFORMATION
4.1 The chart information to be used in ECDIS should be the latest edition, as corrected by
official updates, of that issued by or on the authority of a Government,
government-authorized Hydrographic Office or other relevant government institution, and
conform to IHO standards2.
4.2 The contents of the SENC should be adequate and up-to-date for the intended voyage to
comply with regulation V/27 of the 1974 SOLAS Convention as amended.
4.3 It should not be possible to alter the contents of the ENC or SENC information
transformed from the ENC.
4.4 Updates should be stored separately from the ENC.
4.5 ECDIS should be capable of accepting official updates to the ENC data provided in
conformity with IHO standards. These updates should be automatically applied to the
SENC. By whatever means updates are received, the implementation procedure should
not interfere with the display in use.
4.6 ECDIS should also be capable of accepting updates to the ENC data entered manually
with simple means for verification prior to the final acceptance of the data. They should
be distinguishable on the display from ENC information and its official updates and not
affect display legibility.
4.7 ECDIS should keep and display on demand a record of updates including time of
application to the SENC. This record should include updates for each ENC until it is
superseded by a new edition.
4.8 ECDIS should allow the mariner to display updates in order to review their contents and
to ascertain that they have been included in the SENC.
4.9 ECDIS should be capable of accepting both non-encrypted ENCs and ENCs encrypted in
accordance with the IHO Data Protection Scheme3.
2
IHO Special Publication S-52 and S-57 (see appendix 1).
3
IHO Special Publication S-63 (see appendix 1).
Page 5
MODULE B OPERATIONAL AND FUNCTIONAL REQUIREMENTS
5 DISPLAY OF SENC INFORMATION
5.1 ECDIS should be capable of displaying all SENC information. An ECDIS should be
capable of accepting and converting an ENC and its updates into a SENC. The ECDIS
may also be capable of accepting a SENC resulting from conversion of ENC to SENC
ashore, in accordance with IHO TR 3.114. This method of ENC supply is known as
SENC delivery.
5.2 SENC information available for display during route planning and route monitoring
should be subdivided into the following three categories, Display Base, Standard Display
and All Other Information (see appendix 2).
5.3 ECDIS should present the Standard Display at any time by a single operator action.
5.4 When an ECDIS is switched on following a switch off or power failure, it should return
to the most recent manually selected settings for display.
5.5 It should be easy to add or remove information from the ECDIS display. It should not be
possible to remove information contained in the Display Base.
5.6 For any operator identified geographical position (e.g. by cursor picking) ECDIS should
display on demand the information about the chart objects associated with such a
position.
5.7 It should be possible to change the display scale by appropriate steps e.g. by means of
either chart scale values or ranges in nautical miles.
5.8 It should be possible for the mariner to select a safety contour from the depth contours
provided by the SENC. ECDIS should emphasize the safety contour over other contours
on the display, however:
.1 if the mariner does not specify a safety contour, this should default to 30m. If the
safety contour specified by the mariner or the default 30 m contour is not in the
displayed SENC, the safety contour shown should default to the next deeper
contour;
.2 if the safety contour in use becomes unavailable due to a change in source data,
the safety contour should default to the next deeper contour; and
.3 in each of the above cases, an indication should be provided.
5.9 It should be possible for the mariner to select a safety depth. ECDIS should emphasize
soundings equal to or less than the safety depth whenever spot soundings are selected for
display.
5.10 The ENC and all updates to it should be displayed without any degradation of their
information content.
4
IHO Miscellaneous Publication M-3.
Page 6
5.11 ECDIS should provide a means to ensure that the ENC and all updates to it have been
correctly loaded into the SENC.
5.12 The ENC data and updates to it should be clearly distinguishable from other displayed
information, including those listed in appendix 3.
6 SCALE
6.1 ECDIS should provide an indication if:
.1 the information is displayed at a larger scale than that contained in the ENC; or
.2 own ships position is covered by an ENC at a larger scale than that provided by
the display.
7 DISPLAY OF OTHER NAVIGATIONAL INFORMATION
7.1 Radar information and/or AIS information may be transferred from systems compliant
with the relevant standards of the Organization. Other navigational information may be
added to the ECDIS display. However, it should not degrade the displayed SENC
information and it should be clearly distinguishable from the SENC information.
7.2 It should be possible to remove the radar information, AIS information and other
navigational information by single operator action.
7.3 ECDIS and added navigational information should use a common reference system. If
this is not the case, an indication should be provided.
7.4 Radar
7.4.1 Transferred radar information may contain a radar image and/or tracked target
information.
7.4.2 If the radar image is added to the ECDIS display, the chart and the radar image should
match in scale, projection and in orientation.
7.4.3 The radar image and the position from the position sensor should both be adjusted
automatically for antenna offset from the conning position.
8 DISPLAY MODE AND GENERATION OF THE NEIGHBOURING AREA
8.1 It should always be possible to display the SENC information in a north-up orientation.
Other orientations are permitted. When such orientations are displayed, the orientation
should be altered in steps large enough to avoid unstable display of the chart information.
8.2 ECDIS should provide for true motion mode. Other modes are permitted.
8.3 When true motion mode is in use, reset and generation of the chart display of the
neighbouring area should take place automatically at own ship's distance from the edge of
the display as determined by the mariner.
Page 7
8.4 It should be possible to manually change the displayed chart area and the position of own
ship relative to the edge of the display.
8.5 If the area covered by the ECDIS display includes waters for which no ENC at a scale
appropriate for navigation is available, the areas representing those waters should carry an
indication (see appendix 5) to the mariner to refer to the paper chart or to the RCDS mode
of operation (see appendix 7).
9 COLOURS AND SYMBOLS
9.1 IHO recommended colours and symbols should be used to represent SENC information5.
9.2 The colours and symbols other than those mentioned in 9.1 should comply with the
applicable requirements contained in the IMO standards for navigational symbols6.
9.3 SENC information displayed at the scale specified in the ENC should use the specified
size of symbols, figures and letters5.
9.4 ECDIS should allow the mariner to select whether own ship is displayed in true scale or
as a symbol.
10 DISPLAY REQUIREMENTS
10.1 ECDIS should be capable of displaying information for:
.1 route planning and supplementary navigation tasks; and
.2 route monitoring.
10.2 The effective size of the chart presentation for route monitoring should be at
least 270 mm x 270 mm.
10.3 The display should be capable of meeting colour and resolution recommendations of
IHO5.
10.4 The method of presentation should ensure that the displayed information is clearly visible
to more than one observer in the conditions of light normally experienced on the bridge of
the ship by day and by night.
10.5 If information categories included in the Standard Display (See appendix 2) are removed
to customize the display, this should be permanently indicated. Identification of
categories which are removed from the Standard Display should be shown on demand.
5
Special Publication S-52, Appendix 2 (see appendix 1)
Page 8
11 ROUTE PLANNING, MONITORING AND VOYAGE RECORDING
11.1 It should be possible to carry out route planning and route monitoring in a simple and
reliable manner.
11.2 The largest scale data available in the SENC for the area given should always be used by
the ECDIS for all alarms or indications of crossing the ship's safety contour and of
entering a prohibited area, and for alarms and indications according to appendix 5.
11.3 Route Planning
11.3.1 It should be possible to carry out route planning including both straight and curved
segments.
11.3.2 It should be possible to adjust a planned route alphanumerically and graphically

including:
.1 adding waypoints to a route;
.2 deleting waypoints from a route; and
.3 changing the position of a waypoint.
11.3.3 It should be possible to plan one or more alternative routes in addition to the selected
route. The selected route should be clearly distinguishable from the other routes.
11.3.4 An indication is required if the mariner plans a route across an own ship's safety contour.
11.3.5 An indication should be given if the mariner plans a route closer than a user-specified
distance from the boundary of a prohibited area or a geographic area for which special conditions
exist (see appendix 4).An indication should also be given if the mariner plans a route closer than
a user-specified distance from a point object, such as a fixed or floating aid to navigation or
isolated danger.
11.3.6 It should be possible for the mariner to specify a cross track limit of deviation from the
planned route at which an automatic off-track alarm should be activated.
11.4 Route monitoring
11.4.1 For route monitoring the selected route and own ship's position should appear whenever
the display covers that area.
11.4.2 It should be possible to display a sea area that does not have the ship on the display (e.g.
for look ahead, route planning), while route monitoring. If this is done on the display
used for route monitoring, the automatic route monitoring functions (e.g. updating ships
position, and providing alarms and indications) should be continuous. It should be
possible to return to the route monitoring display covering own ship's position
immediately by single operator action.
11.4.3 ECDIS should give an alarm if, within a specified time set by the mariner, own ship will
cross the safety contour.
Page 9
11.4.4 ECDIS should give an alarm or indication, as selected by the mariner, if, within a
specified time set by the mariner, own ship will cross the boundary of a prohibited area
or of a geographical area for which special conditions exist (see appendix 4).
11.4.5 An alarm should be given when the specified cross track limit for deviation from the
planned route is exceeded.
11.4.6 An indication should be given to the mariner if, continuing on its present course and
speed, over a specified time or distance set by the mariner, own ship will pass closer
than a user-specified distance from a danger (e.g. obstruction, wreck, rock) that is
shallower than the mariner's safety contour or an aid to navigation.
11.4.7 The ships position should be derived from a continuous positioning system of an
accuracy consistent with the requirements of safe navigation. Whenever possible, a
second independent positioning source, preferably of a different type, should be
provided. In such cases ECDIS should be capable of identifying discrepancies between
the two sources.
11.4.8 ECDIS should provide an alarm when the input from position, heading or speed sources
is lost. ECDIS should also repeat, but only as an indication, any alarm or indication
passed to it from position, heading or speed sources.
11.4.9 An alarm should be given by ECDIS when the ship reaches a specified time or distance,
set by the mariner, in advance of a critical point on the planned route.
11.4.10 The positioning system and the SENC should be on the same geodetic datum. ECDIS
should give an alarm if this is not the case.
11.4.11 It should be possible to display alternative routes in addition to the selected route. The
selected route should be clearly distinguishable from the other routes. During the
voyage, it should be possible for the mariner to modify the selected sailing route or
change to an alternative route.
11.4.12 It should be possible to display:
.1 time-labels along a ship's track manually on demand and automatically at intervals

selected between 1 and 120 minutes; and
.2 an adequate number of: points, free movable electronic bearing lines, variable and
fixed range markers and other symbols required for navigation purposes and
specified in appendix 3.
11.4.13 It should be possible to enter the geographical co-ordinates of any position and then
display that position on demand. Also, it should be possible to select any point
(features, symbol or position) on the display and read its geographical co-ordinates on
demand.
11.4.14 It should be possible to adjust the displayed geographic position of the ship manually.
This manual adjustment should be noted alpha-numerically on the screen, maintained
until altered by the mariner and automatically recorded.
Page 10
11.4.15.1 ECDIS should provide the capability to enter and plot manually obtained bearing and
distance lines of position (LOP), and calculate the resulting position of own ship. It
should be possible to use the resulting position as an origin for dead-reckoning.
11.4.15.2 ECDIS should indicate discrepancies between the positions obtained by continuous
positioning systems and positions obtained by manual observations.
11.5 Voyage recording
11.5.1 ECDIS should store and be able to reproduce certain minimum elements required to
reconstruct the navigation and verify the official database used during the previous 12
hours. The following data should be recorded at one minute intervals:
.1 to ensure a record of own ship's past track: time, position, heading, and speed; and
.2 to ensure a record of official data used: ENC source, edition, date, cell and update
history.
11.5.2 In addition, ECDIS should record the complete track for the entire voyage, with time
marks at intervals not exceeding 4 hours.
11.5.3 It should not be possible to manipulate or change the recorded information.
11.5.4 ECDIS should have a capability to preserve the record of the previous 12 hours and of
the voyage track.
12 CALCULATIONS AND ACCURACY
12.1 The accuracy of all calculations performed by ECDIS should be independent of the
characteristics of the output device and should be consistent with the SENC accuracy.
12.2 Bearings and distances drawn on the display or those measured between features already
drawn on the display should have accuracy no less than that afforded by the resolution of
the display.
12.3 The system should be capable of performing and presenting the results of at least the
following calculations:
.1 true distance and azimuth between two geographical positions;
.2 geographic position from known position and distance/azimuth; and
.3 geodetic calculations such as spheroidal distance, rhumb line, and great circle.
Page 11
13 PERFORMANCE TESTS, MALFUNCTIONS ALARMS AND INDICATIONS
13.1 ECDIS should be provided with means for either automatically or manually carrying out
on-board tests of major functions. In case of a failure, the test should display information
to indicate which module is at fault.
13.2 ECDIS should provide a suitable alarm or indication of system malfunction.
14 BACK-UP ARRANGEMENTS
Adequate back-up arrangements should be provided to ensure safe navigation in case of

an ECDIS failure; see appendix 6.
.1 Facilities enabling a safe take-over of the ECDIS functions should be provided

in order to ensure that an ECDIS failure does not develop into a critical
situation.
.2 A back-up arrangement should provide means of safe navigation for the

remaining part of a voyage in the case of an ECDIS failure.
MODULE C INTERFACING AND INTEGRATION
15 CONNECTIONS WITH OTHER EQUIPMENT 7
15.1 ECDIS should not degrade the performance of any equipment providing sensor inputs.
Nor should the connection of optional equipment degrade the performance of ECDIS
below this standard.
15.2 ECDIS should be connected to the ship's position fixing system, to the gyro compass and
to the speed and distance measuring device. For ships not fitted with a gyro compass,
ECDIS should be connected to a marine transmitting heading device.
15.3 ECDIS may provide a means to supply SENC information to external equipment.
16 POWER SUPPLY
16.1 It should be possible to operate ECDIS and all equipment necessary for its normal
functioning when supplied by an emergency source of electrical power in accordance
with the appropriate requirements of chapter II-1 of the 1974 SOLAS Convention, as
amended.
16.2 Changing from one source of power supply to another or any interruption of the supply
for a period of up to 45 seconds should not require the equipment to be manually
re-initialized.
7 Publication IEC 61162.
Page 12
Appendix 1
REFERENCE DOCUMENTS
The following international organizations have developed technical standards and

specifications, as listed below, for use in conjunction with this standard. The latest edition of
these documents should be obtained from the organization concerned:
INTERNATIONAL MARITIME ORGANIZATION (IMO)
Address: International Maritime Organization Phone: +44 207 735 76 11

4 Albert Embankment Fax: +44 207 587 32 10
London SE1 7SR E-mail:[email protected]
United Kingdom Web: http://www.imo.org
Publications
IMO resolution MSC.191(79) on Performance Standards for the presentation of

navigation related information on shipborne navigational displays
IMO resolution A.694(17) on Recommendations on general requirements for shipborne

radio equipment forming part of the Global Maritime Distress and Safety System
(GMDSS) and for electronic navigational aids
SN.Circ/207 (1999) on Differences between RCDS and ECDIS
IMO SN/Circ.243 (2004) on Guidelines for the Presentation of Navigation-related

Symbols, Terms and Abbreviations
IMO MSC/Circ.982 (2000) on Guidelines on ergonomic criteria for bridge equipment and
layout
INTERNATIONAL HYDROGRAPHIC ORGANIZATION (IHO)
Address: Directing Committee Phone: +377 93 10 81 00

International Hydrographic Bureau Fax: +377 93 10 81 40
BP 445 E-mail:[email protected]
MC 98011 Monaco Cedex Web: http://www.iho.shom.fr
Principality of Monaco
Page 13
Publications
Special Publication No. S-52, Specifications for Chart Content and Display Aspects of
ECDIS
Special Publication No. S-52 appendix 1, Guidance on Updating the Electronic

Navigational Chart
Special Publication No. S-52 appendix 2, Colour and Symbol Specifications for ECDIS
Special Publication No. S-32, Hydrographic Dictionary
Special Publication No. S-57, IHO Transfer Standard for Digital Hydrographic Data
Special Publication No. S-61, IHO Product specification for Raster Navigational Charts
(RNC)
Special Publication No. S-63, IHO Data Protection Scheme
Miscellaneous Publication No. M-3, Resolutions of the IHO
INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC)
Address: IEC Central Office Phone: +41 22 734 01 50

3 rue de Varemb Fax: +41 22 733 38 43
PO Box 131
CH-1211 Geneva 20
Switzerland
Publications
IEC Publication 61174, Electronic Chart Display and Information Systems (ECDIS) -
Operational and Performance Requirements, Method of Testing and Required Test
Results.
IEC Publication 60945, General Requirements for Shipborne Radio Equipment Forming
Part of the Global Maritime Distress and Safety System and Marine Navigational
Equipment.
IEC Publication 61162, Digital Interfaces - Navigation and Radiocommunication

Equipment On board Ship.
[IEC Publication 62288, Maritime Navigation and Radiocommunication Equipment and

Systems Presentation of navigation related information General requirements,
methods of test and required test results.]
Page 14
Appendix 2
SENC INFORMATION AVAILABLE FOR DISPLAY DURING ROUTE PLANNING

AND ROUTE MONITORING
1 Display base to be permanently shown on the ECDIS display, consisting of:
.1 coastline (high water);

.2 own ship's safety contour;
.3 isolated underwater dangers of depths less than the safety contour which lie
within the safe waters defined by the safety contour;
.4 isolated dangers which lie within the safe water defined by the safety contour,
such as fixed structures, overhead wires, etc.;
.5 scale, range and north arrow;
.6 units of depth and height; and
.7 display mode.
2 Standard display consisting of:
.1 display base
.2 drying line
.3 buoys, beacons, other aids to navigation and fixed structures
.4 boundaries of fairways, channels, etc.
.5 visual and radar conspicuous features
.6 prohibited and restricted areas
.7 chart scale boundaries
.8 indication of cautionary notes
.9 ships routeing systems and ferry routes
.10 archipelagic sea lanes.
3 All other information, to be displayed individually on demand, for example:
.1 spot soundings
.2 submarine cables and pipelines
.3 details of all isolated dangers
.4 details of aids to navigation
.5 contents of cautionary notes
.6 ENC edition date
.7 most recent chart update number
.8 magnetic variation
.9 graticule
.10 place names.
Page 15
Appendix 3
NAVIGATIONAL ELEMENTS AND PARAMETERS
1 Own ship.
.1 Past track with time marks for primary track.

.2 Past track with time marks for secondary track.
2 Vector for course and speed made good.
3 Variable range marker and/or electronic bearing line.
4 Cursor.
5 Event.
.1 Dead reckoning position and time (DR).

.2 Estimated position and time (EP).
6 Fix and time.
7 Position line and time.
8 Transferred position line and time.
.1 Predicted tidal stream or current vector with effective time and strength.
.2 Measured tidal stream or current vector with effective time and strength.
9 Danger highlight.
10 Clearing line.
11 Planned course and speed to make good.
12 Waypoint.
13 Distance to run.
14 Planned position with date and time.
15 Visual limits of lights arc to show rising/dipping range.
16 Position and time of wheel over.
Page 16
Appendix 4
AREAS FOR WHICH SPECIAL CONDITIONS EXIST
The following are the areas which ECDIS should detect and provide an alarm or
indication under sections 11.3.5 and 11.4.4:
Traffic separation zone

Inshore traffic zone
Restricted area
Caution area
Offshore production area
Areas to be avoided
User defined areas to be avoided
Military practise area
Seaplane landing area
Submarine transit lane
Anchorage area
Marine farm/aquaculture
PSSA (Particularly Sensitive Sea Area)
Page 17
Appendix 5
ALARMS AND INDICATORS
Section Requirements Information

11.4.3 Alarm Crossing safety contour
11.4.4 Alarm or Indication Area with special conditions
11.4.5 Alarm Deviation from route
11.4.8 Alarm Positioning system failure
11.4.9 Alarm Approach to critical point
11.4.10 Alarm Different geodetic datum
13.2 Alarm or Indication Malfunction of ECDIS
5.8.3 Indication Default safety contour

6.1.1 Indication Information overscale
6.1.2 Indication Larger scale ENC available
7.3 Indication Different reference system
8.5 Indication No ENC available
10.5 Indication Customized display
11.3 4 Indication Route planning across safety contour
11.3.5 Indication Route planning across specified area
11.4.6 Indication Crossing a danger in route
monitoring mode
13.1 Indication System test failure
In this Performance Standard the definitions of Indicators and Alarms provided in the IMO
resolution A.830(19) Code on Alarms and Indicators, 1995 apply.
Alarm: An alarm or alarm system which announces by audible means, or audible and visual
means, a condition requiring attention.
Indicator: Visual indication giving information about the condition of a system or equipment.
Page 18
Appendix 6
BACK-UP REQUIREMENTS
1 INTRODUCTION
As prescribed in section 14 of this performance standard, adequate independent back-up

arrangements should be provided to ensure safe navigation in case of ECDIS failure. Such
arrangements include:
.1 facilities enabling a safe take-over of the ECDIS functions in order to ensure that
an ECDIS failure does not result in a critical situation;
.2 a means to provide for safe navigation for the remaining part of the voyage in case
of ECDIS failure.
2 PURPOSE
The purpose of an ECDIS back-up system is to ensure that safe navigation is not
compromised in the event of ECDIS failure. This should include a timely transfer to the back-up
system during critical navigation situations. The back-up system shall allow the vessel to be
navigated safely until the termination of the voyage.
3 FUNCTIONAL REQUIREMENTS
3.1 Required functions and their availability
3.1.1 Presentation of chart information
The back-up system should display in graphical (chart) form the relevant information of the
hydrographic and geographic environment which are necessary for safe navigation.
3.1.2 Route planning
The back-up system should be capable of performing the route planning functions, including:
.1 taking over of the route plan originally performed on the ECDIS;
.2 adjusting a planned route manually or by transfer from a route planning device.
3.1.3 Route monitoring
The back-up system should enable a take-over of the route monitoring originally performed by
the ECDIS, and provide at least the following functions:
.1 plotting own ships position automatically, or manually on a chart;
.2 taking courses, distances and bearings from the chart;
.3 displaying the planned route;
Page 19
.4 displaying time labels along ships track;
.5 plotting an adequate number of points, bearing lines, range markers, etc., on the
chart.
3.1.4 Display information
If the back-up is an electronic device, it should be capable of displaying at least the information
equivalent to the standard display as defined in this performance standard.
3.1.5 Provision of chart information
.1 The chart information to be used in the backup arrangement should be the latest
edition, as corrected by official updates, of that issued by or on the authority of a
Government, authorized Hydrographic Office or other relevant government
institution, and conform to IHO standards.
.2 It should not be possible to alter the contents of the electronic chart information.
.3 The chart or chart data edition and issuing date should be indicated.
3.1.6 Updating
The information displayed by the ECDIS back-up arrangements should be up-to-date for the
entire voyage.
3.1.7 Scale
If an electronic device is used, it should provide an indication:
.1 if the information is displayed at a larger scale than that contained in the database;
and
.2 if own ships position is covered by a chart at a larger scale than that provided by
the system.
3.1.8 If radar and other navigational information are added to an electronic back-up display, all
the corresponding requirements for radar information and other navigation information of
this performance standard should be met.
3.1.9 If an electronic device is used, the display mode and generation of the neighbouring area
should be in accordance with section 8 of this performance standard.
3.1.10 Voyage recording
The back-up arrangements should be able to keep a record of the ships actual track, including
positions and corresponding times.
Page 20
3.2 Reliability and accuracy
3.2.1 Reliability
The back-up arrangements should provide reliable operation under prevailing environmental and
normal operating conditions.
3.2.2 Accuracy
Accuracy should be in accordance with section 12 of this performance standard.
3.3 Malfunctions, warnings, alarms and indications
If an electronic device is used, it should provide a suitable alarm or indication of system malfunction.
4 OPERATIONAL REQUIREMENTS
4.1 Ergonomics
If an electronic device is used, it should be designed in accordance with the ergonomic principles
of ECDIS.
4.2 Presentation of information
If an electronic device is used:
.1 Colours and symbols should be in accordance with the colours and symbols
requirements of ECDIS.
.2 The effective size of the chart presentation should be not less than 250 mm x 250 mm
or 250 mm diameter.
5 POWER SUPPLY
If an electronic device is used:
.1 the back-up power supply should be separate from the ECDIS; and
.2 conform to the requirements in this ECDIS performance standard.
6 CONNECTIONS WITH OTHER EQUIPMENT
6.1 If an electronic device is used, it should:
.1 be connected to systems providing continuous position-fixing capability; and
.2 not degrade the performance of any equipment providing sensor input.
6.2 If radar with selected parts of the ENC chart information overlay is used as an element of
the back-up, the radar should comply with resolution MSC.192(79).
Page 21
Appendix 7
RCDS MODE OF OPERATION
Whenever in this appendix reference is made to any provisions of the annex related to ECDIS,
the term ECDIS should be substituted by the term RCDS, SENC by SRNC and ENC by RNC, as
appropriate.
This appendix refers to each paragraph of the performance standards for ECDIS (i.e. the Annex
to which this part is appendix 7) and specifies which paragraphs of the Annex either:
.1 apply to RCDS; or
.2 do not apply to RCDS; or
.3 are modified or replaced as shown in order to apply to RCDS.
Any additional requirements applicable to RCDS are also described.
1 SCOPE
1.1 Paragraph applies to RCDS.
1.2 When operating in RCDS-mode, an appropriate portfolio of up-to-date paper

charts (APC) should be carried on board and be readily available to the mariner.
1.3 - 1.7 Paragraphs apply to RCDS.
1.8 RCDS should provide appropriate alarms or indications with respect to the
information displayed or malfunction of the equipment (see Table 1 of this
appendix).
1.9 Refers to Appendix 7 and applies to RCDS.
2 APPLICATION OF THESE STANDARDS
2.1 2.4 Paragraphs apply to RCDS.
3 DEFINITIONS
3.1 Raster Chart Display System (RCDS) means a navigation information system
displaying RNCs with positional information from navigation sensors to assist the
mariner in route planning and route monitoring, and if required, display additional
navigation-related information.
3.2 Raster Navigational Chart (RNC) means a facsimile of a paper chart originated
by, or distributed on the authority of, a government-authorized hydrographic
office. RNC is used in these standards to mean either a single chart or a collection
of charts.
Page 22
3.3 System Raster Navigational Chart Database (SRNC) means a database resulting
from the transformation of the RNC by the RCDS to include updates to the RNC
by appropriate means.
3.4-3.5 Paragraphs do not apply to RCDS.
3.7 Appropriate Portfolio of up to date paper Charts (APC) means a suite of paper
charts of a scale to show sufficient detail of topography, depths, navigational
hazards, aids to navigation, charted routes, and routeing measures to provide the
mariner with information on the overall navigational environment. The APC
should provide adequate look-ahead capability. Coastal States will provide details
of the charts which meet the requirement of this portfolio, and these details are
included in a worldwide database maintained by the IHO. Consideration should
be given to the details contained in this database when determining the content of
the APC.
MODULE A - DATABASE
4 PROVISION AND UPDATING OF CHART INFORMATION
4.1 The RNC used in RCDS should be the latest edition of that originated by, or
distributed on the authority of, a government authorized hydrographic office and
conform to IHO standards. RNCs not on WGS 84 or PE-90 should carry meta-
data (i.e., additional data) to allow geo-referenced positional data to be displayed
in the correct relationship to SRNC data.
4.2 The contents of the SRNC should be adequate and up-to-date for that part of the
intended voyage not covered by ENC.
4.3 It should not be possible to alter the contents of the RNC.
4.4 4.8 All paragraphs apply to RCDS.
4.9 Paragraph does not apply to RCDS
MODULE B OPERATIONAL AND FUNCTIONAL REQUIREMENTS
5 DISPLAY OF SRNC INFORMATION
5.1 RCDS should be capable of displaying all SRNC information.
5.2 SRNC information available for display during route planning and route
monitoring should be subdivided into two categories:
.1 the RCDS standard display consisting of RNC and its updates, including
its scale, the scale at which it is displayed, its horizontal datum, and its
units of depths and heights; and
.2 any other information such as mariners notes.
Page 23
5.3- 5.4 Paragraphs apply to RCDS.
5.5 It should be easy to add to, or remove from; the RCDS display any information
additional to the RNC data, such as mariner's notes. It should not be possible to
remove any information from the RNC.
5.6 5.9 Paragraphs do not apply to RCDS.
5.10 5.12 Paragraphs apply to RCDS.
5.13 There should always be an indication if the ECDIS equipment is operating in

RCDS mode.
6 SCALE
This section applies to RCDS.
7 DISPLAY OF OTHER NAVIGATIONAL INFORMATION
7.1 - 7.4 All paragraphs apply to RCDS.
8 DISPLAY MODE AND GENERATION OF THE NEIGHBOURING AREA
8.1 It should always be possible to display the SRNC in chart-up orientation. Other
orientations are permitted.
8.2 - 8.4 All paragraphs apply to RCDS.
8.5 Paragraph refers to RCDS mode of operation.
9 COLOURS AND SYMBOLS
9.1 IHO recommended colours and symbols should be used to represent SRNC
information.
9.3 Paragraph does not apply to RCDS.
10 DISPLAY REQUIREMENTS
10.1-10.2 Paragraphs apply to RCDS.
Page 24
10.6 RCDS should be capable of displaying, simply and quickly, chart notes which are
not located on the portion of the chart currently being displayed.
11 ROUTE PLANNING, MONITORING AND VOYAGE RECORDING
11.1 Paragraphs apply to RCDS.
11.3 Route Planning
11.3.1-11.3.3 Paragraphs apply to RCDS.
11.3.4-11.3.5 Paragraphs do not apply to RCDS.
11.3.6 Paragraph applies to RCDS.
11.3.7 It should be possible for the mariner to enter points, lines and areas which activate
an automatic alarm. The display of these features should not degrade the SRNC
information and it should be clearly distinguishable from the SRNC information.
11.4 Route monitoring
11.4.1 Paragraph applies to RCDS.
11.4.2 It should be possible to display a sea area that does not have the ship on the
display (e.g. for look ahead, route planning), while route monitoring. If this is
done on the display used for route monitoring, the automatic route monitoring
functions in 10.4.6 and 10.4.7 should be continuous. It should be possible to
return to the route monitoring display covering own ship's position immediately
by single operator action.
11.4.3-11.4.4 Paragraphs do not apply to RCDS.
11.4.5 Paragraph apply to RCDS.
11.4.6 Paragraphs do not apply to RCDS.
11.4.10 The RCDS should only accept positional data referenced to the WGS 84 or PE-90
geodetic datum. RCDS should give an alarm if the positional data is not
referenced to one of these datum. If the displayed RNC cannot be referenced to
the WGS 84 or PE-90 datum then a continuous indication should be provided.
Page 25
11.4.16 RCDS should allow the user to manually align the SRNC with positional data.
This can be necessary, for example, to compensate for local charting errors.
11.4.17 It should be possible to activate an automatic alarm when the ship crosses a point,
line, or is within the boundary of a mariner entered feature within a specified time
or distance.
11.5 Voyage recording
11.5.1-11.5.4 All paragraphs apply to RCDS.
12 CALCULATIONS AND ACCURACY
12.1-12.3 All paragraphs apply to RCDS.
12.4 RCDS should be capable of performing transformations between a local datum

and WGS 84 Datum.
13 PERFORMANCE TESTS, MALFUNCTION ALARMS AND INDICATIONS
14 BACK-UP ARRANGEMENTS
All paragraphs apply to RCDS.
MODULE C INTERFACING AND INTEGRATION
15 CONNECTIONS WITH OTHER EQUIPMENT
16 POWER SUPPLY
Page 26
Table 1
ALARMS AND INDICATORS IN THE RCDS MODE OF OPERATION
Paragraph Requirement Information
11.4.5 Alarm Deviation from route

11.4.17 Alarm Approach to mariner entered feature, e.g. area, line
11.4.8 Alarm Position system failure
11.4.9 Alarm Approach to critical point
11.4.10 Alarm or Different geodetic datum
indication
13.2 Alarm or Malfunction of RCDS mode
indication
5.13 Indication ECDIS operating in the raster mode

6.1 Indication Larger scale information available, or overscale
6.1.2 Indication Larger scale RNC available for the area of the vessel
Note: The definitions of alarms and indicators are given in appendix 5.
***
ADOPTION OF THE REVISED PERFORMANCE

ECDIS

Uploaded by

Copyright:

Available Formats

ECDIS

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ECDIS

Uploaded by

Copyright:

Available Formats

RESOLUTION MSC.

(adopted on 5 December 2006)

ADOPTION OF THE REVISED PERFORMANCE STANDARDS FOR

THE MARITIME SAFETY COMMITTEE,

RECALLING Article 28(b) of the Convention on the International Maritime Organization

RECOGNIZING the need to improve the previously adopted, by resolution A.817(19), as

HAVING CONSIDERED the recommendation made by the Sub-Committee on Safety of

2. RECOMMENDS Governments ensure that ECDIS equipment:

(a) if installed on or after 1 January 2009, conform to performance standards not

REVISED PERFORMANCE STANDARDS FOR ELECTRONIC CHART DISPLAY

1.1 The primary function of the ECDIS is to contribute to safe navigation.

2 APPLICATION OF THESE STANDARDS

- dedicated standalone workstation.

For the purpose of these performance standards:

4 PROVISION AND UPDATING OF CHART INFORMATION

4.4 Updates should be stored separately from the ENC.

MODULE B OPERATIONAL AND FUNCTIONAL REQUIREMENTS

5 DISPLAY OF SENC INFORMATION

.3 in each of the above cases, an indication should be provided.

6.1 ECDIS should provide an indication if:

7 DISPLAY OF OTHER NAVIGATIONAL INFORMATION

8 DISPLAY MODE AND GENERATION OF THE NEIGHBOURING AREA

9 COLOURS AND SYMBOLS

10.1 ECDIS should be capable of displaying information for:

.1 route planning and supplementary navigation tasks; and

11 ROUTE PLANNING, MONITORING AND VOYAGE RECORDING

11.3 Route Planning

11.3.2 It should be possible to adjust a planned route alphanumerically and graphically

.1 adding waypoints to a route;

.2 deleting waypoints from a route; and

.3 changing the position of a waypoint.

11.4 Route monitoring

11.4.12 It should be possible to display:

.1 time-labels along a ship's track manually on demand and automatically at intervals

11.5 Voyage recording

11.5.3 It should not be possible to manipulate or change the recorded information.

12 CALCULATIONS AND ACCURACY

.1 true distance and azimuth between two geographical positions;

.2 geographic position from known position and distance/azimuth; and

13 PERFORMANCE TESTS, MALFUNCTIONS ALARMS AND INDICATIONS

13.2 ECDIS should provide a suitable alarm or indication of system malfunction.

Adequate back-up arrangements should be provided to ensure safe navigation in case of

.1 Facilities enabling a safe take-over of the ECDIS functions should be provided

.2 A back-up arrangement should provide means of safe navigation for the

MODULE C INTERFACING AND INTEGRATION

15 CONNECTIONS WITH OTHER EQUIPMENT 7

7 Publication IEC 61162.

The following international organizations have developed technical standards and

INTERNATIONAL MARITIME ORGANIZATION (IMO)

Address: International Maritime Organization Phone: +44 207 735 76 11

IMO resolution MSC.191(79) on Performance Standards for the presentation of

IMO resolution A.694(17) on Recommendations on general requirements for shipborne

SN.Circ/207 (1999) on Differences between RCDS and ECDIS

IMO SN/Circ.243 (2004) on Guidelines for the Presentation of Navigation-related

INTERNATIONAL HYDROGRAPHIC ORGANIZATION (IHO)

Address: Directing Committee Phone: +377 93 10 81 00

Special Publication No. S-52 appendix 1, Guidance on Updating the Electronic

Special Publication No. S-32, Hydrographic Dictionary

Special Publication No. S-63, IHO Data Protection Scheme