Scribd
Upload
95 views47 pages

INTRODUCTION (Cont..) : TIN 205-TIN31 Engineering Mechanics

This document outlines the syllabus for the TIN205-TIN31 Engineering Mechanics course, which is worth 2 credit hours. The course involves lectures, quizzes, assignments, a midterm exam, and a final exam. Key topics covered include equilibrium of deformable bodies, stress, strain, deflection, stability, average normal and shear stress, procedures for analysis, design of simple connections, and examples. Assessment is based 30% on quizzes and assignments, 30% on the midterm, and 40% on the final exam.

Uploaded by

gundul pacul
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
95 views47 pages

INTRODUCTION (Cont..) : TIN 205-TIN31 Engineering Mechanics

This document outlines the syllabus for the TIN205-TIN31 Engineering Mechanics course, which is worth 2 credit hours. The course involves lectures, quizzes, assignments, a midterm exam, and a final exam. Key topics covered include equilibrium of deformable bodies, stress, strain, deflection, stability, average normal and shear stress, procedures for analysis, design of simple connections, and examples. Assessment is based 30% on quizzes and assignments, 30% on the midterm, and 40% on the final exam.

Uploaded by

gundul pacul
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 47

INTRODUCTION (Cont..

)
TIN205-TIN31 Engineering Mechanics
2 CREDIT HOURS
2 Hours for lecture
Assessment/marks distribution
Quizzes/Assignments - 30%
Mid Term Exam - 30%
Final Exam - 40%
REFERENCES

1. R.C. Hibbeler (2011) Mechanics of Materials. 8th


Edition, SI Units, Prentice Hall
2. F. Beer, E.R. Johnston, Jr., J.T. Dewolf, and D. Mazurek
(2010), Mechanics of Materials. 6th Edition, McGrow Hill.
INTRODUCTION (Cont)
Mechanics of materials is a study of the
relationship between the external loads
on a body and the internal stresses
within that body.
This subject also involves the
deformations and stability of a body when
subjected to external forces.
INTRODUCTION (Cont)
External Loads
External Forces
Internal (Resultant) Forces
Stress (function of member shape and loading)
Strain (function of material properties, member
shape and loading)
Deflection (function of material properties, member
shape and loading)
Stability (failure)
Equilibrium of Deformable Body

External Forces
1. Surface forces - caused by direct contact of other bodys
surface (point, line, area)
2. Body forces - other body exerts a force without contact
(gravity)
Equilibrium of Deformable Body
Reaction
Surface forces developed at the supports/points of contact
between
Equilibrium of Deformable Body
Equation of Equilibrium
Equilibrium of a body requires a balance of forces and a
balance of moments

For a body with x, y, z coordinate system with origin O,

Best way to account for these forces is to draw the bodys


free-body diagram (FBD).
Equilibrium of Deformable Body
Internal Resultant Loadings (Forces)
To obtain the internal loadings acting on a specific region within the
body, it Is necessary to pass an imaginary section or cut through the
region where the internal loading are to be determined.

Use Free Body Diagram (FBD) and equilibrium equations to determine


the internal force and moment acting within the body

Point O is usually chosen at the centroid of the sectioned area.


Equilibrium of Deformable Body
Three Dimensions
In general, there four different types of resultant loadings as defined
below:
Equilibrium of Deformable Body
Coplanar Loadings (Two dimensions)
In general, there four different types of resultant loadings as defined
below:

Normal force N, shear force V and bending moment M can be


determined by:
Procedure for Analysis
The resultant internal loadings at a point located on the section of a
body can be obtained using the method of sections. This requires the
following steps

Support Reactions
Procedure for Analysis

Free-Body Diagram
Procedure for Analysis
Equations of Equilibrium
Equilibrium of Deformable Body
Example 1.1
Equilibrium of Deformable Body
Example 1.2
Equilibrium of Deformable Body
Example 1.3
Equilibrium of Deformable Body
Example 1.5
Stress
Stress
Average Normal Stress in an Axially Loaded
Bar
Average Normal Stress in an
Axially Loaded Bar
Procedure for Analysis
Example 1.6
Example 1.6
Example 1.7
Example 1.7
Example 1.9
Example 1.9
Average Shear Stress
Procedure for Analysis
Example 1.10
Example 1.10
Example 1.11
Example 1.11
Allowable Stress
Design of Simple Connections

If a member is subjected to a normal force, then the


required area:

If a member is subjected to a shear force, then the


required area:
Design of Simple Connections
Cross Section Area of a Tension Member
Design of Simple Connections
Cross Section Area of a Connector Subjected to Shear
Design of Simple Connections
Required Length of Embedded Rod
Design of Simple Connections
Example 1.13
Design of Simple Connections
Example 1.13
Design of Simple Connections
Example 1.13
Design of Simple Connections
Example 1.14
Design of Simple Connections
Example 1.14
Design of Simple Connections
Example 1.14
Design of Simple Connections
Example 1.15
Design of Simple Connections
Example 1.15

You might also like