INNOLUX DISPLAY CORPORATION

LCD MODULE
S P E C I F I C AT I O N

Customer:
Model Name: AT070TN92
SPEC NO.: A070-92-TT-01
Date: 2009/01/12
Version: 01

Preliminary Specification
Final Specification

For Customer s Acceptance

Approved by Comment

Approved by Review ed by Prepared by

James Yu
Joe Lin Jack Huang David Lee
Charlie Chou
2009/02/12 2009/02/12 2009/02/11

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

 InnoLux copyright 2004
All rights reserved,
Copying forbidden.

Record of Revision
Version Revise Date Page Content
Pre-Spec.01 2009/01/12 Initial Release

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX
Contents

1. General Specifications ............................................................................................................ 1

2. Pin Assignment....................................................................................................................... 2
3. Operation Specifications ......................................................................................................... 5
3.1. Absolute Maximum Rating.............................................................................................. 5
3.1.1. Typical Operation Conditions.................................................................................. 6
3.1.2. Current Consumption ............................................................................................. 7
3.1.3. Backlight Driving Conditions ................................................................................... 7
3.2. Power Sequence ............................................................................................................ 8
3.3. Timing Characteristics .................................................................................................... 9
3.3.1. AC Electrical Characteristics .................................................................................. 9
3.3.2. Data Input Format................................................................................................. 10
3.3.3. Timing................................................................................................................... 11
4. Optical Specifications............................................................................................................ 12
5. Reliability Test Items ............................................................................................................. 16
6. General Precautions ............................................................................................................. 17
6.1. Safety ........................................................................................................................... 17
6.2. Handling ....................................................................................................................... 17
6.3. Static Electricity ............................................................................................................ 17
6.4. Storage ......................................................................................................................... 17
6.5. Cleaning ....................................................................................................................... 17
7. Mechanical Drawing ............................................................................................................. 18
8. Package Drawing ................................................................................................................. 19
8.1 Packaging Material Table.............................................................................................. 19
8.2 Packaging Quantity ...................................................................................................... 19
8.3 Packaging Drawing....................................................................................................... 20

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:1/20

1. General Specifications

No. Item Specification Remark

1 LCD size 7.0 inch(Diagonal)

2 Driver element a-Si TFT active matrix

3 Resolution 800 3(RGB) 480

4 Display mode Normally White, Transmissive

5 Dot pitch 0.0642(W) 0.1790(H) mm

6 Active area 154.08(W) 85.92(H) mm

7 Module size 164.9(W) 100.0(H) 5.7(D) mm Note 1

8 Surface treatment Anti-Glare

9 Color arrangement RGB-stripe

10 Interface Digital

11 Backlight power consumption TBD

12 Panel power consumption TBD

13 Weight TBD

Note 1: Refer to Mechanical Drawing.

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:2/20

2. Pin Assignment

TFT LCD Panel Driving Section

FPC Connector is used for the module electronics interface. The recommended model is
FH12A-50S-0.5SH manufactured by Hirose.
Pin No. Symbol I/O Function Remark
1 VLED+ P Power for LED backlight (Anode)
2 VLED+ P Power for LED backlight (Anode)
3 VLED- P Power for LED backlight (Cathode)
4 VLED- P Power for LED backlight (Cathode)
5 GND P Power ground
6 VCOM I Common voltage
7 DVDD P Power for Digital Circuit
8 MODE I DE/SYNC mode select Note 1
9 DE I Data Input Enable
10 VS I Vertical Sync Input
11 HS I Horizontal Sync Input
12 B7 I Blue data(MSB)
13 B6 I Blue data
14 B5 I Blue data
15 B4 I Blue data
16 B3 I Blue data
17 B2 I Blue data
18 B1 I Blue data Note 2
19 B0 I Blue data(LSB) Note 2
20 G7 I Green data(MSB)
21 G6 I Green data
22 G5 I Green data
23 G4 I Green data
24 G3 I Green data
25 G2 I Green data
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:3/20
26 G1 I Green data Note 2
27 G0 I Green data(LSB) Note 2
28 R7 I Red data(MSB)
29 R6 I Red data
30 R5 I Red data
31 R4 I Red data
32 R3 I Red data
33 R2 I Red data
34 R1 I Red data Note 2
35 R0 I Red data(LSB) Note 2
36 GND P Power Ground
37 DCLK I Sample clock Note 3
38 GND P Power Ground
39 L/R I Left / right selection Note 4,5
40 U/D I Up/down selection Note 4,5
41 VGH P Gate ON Voltage
42 VGL P Gate OFF Voltage
43 AVDD P Power for Analog Circuit
44 RESET I Global reset pin. Note 6
45 NC - No connection
46 VCOM I Common Voltage
47 DITHB I Dithering function Note 7
48 GND P Power Ground
49 NC - No connection
50 NC - No connection
I: input, O: output, P: Power

Note 1: DE/SYNC mode select. Normally pull high.

When select DE mode, MODE=1, VS and HS must pull high.
When select SYNC mode, MODE= 0, DE must be grounded.
Note 2: When input 18 bits RGB data, the two low bits of R,G and B data must be
grounded.
Note 3: Data shall be latched at the falling edge of DCLK.

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:4/20
Note 4: Selection of scanning mode

Setting of scan control input

Scanning direction
U/D L/R
GND DVDD Up to down, left to right
DVDD GND Down to up, right to left
GND GND Up to down, right to left
DVDD DVDD Down to up, left to right

Note 5: Definition of scanning direction.

Refer to the figure as below:

Up

Left Right

Down

Note 6: Global reset pin. Active low to enter reset state. Suggest to connect with an RC
reset circuit for stability. Normally pull high.

Note 7: Dithering function enable control, normally pull high.

When DITHB=1,Disable internal dithering function,
When DITHB=0,Enable internal dithering function,

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:5/20

3. Operation Specifications

3.1. Absolute Maximum Ratings

(Note 1)
Values
Item Symbol Unit Remark
Min. Max.

DVDD -0.3 5.0 V

AVDD 6.5 13.5 V

Power voltage VGH -0.3 40.0 V

VGL -20.0 0.3 V

VGH-VGL - 40.0 V

Operation Temperature TOP -20 70

Storage Temperature TST -30 80

Each LED
LED Reverse Voltage VR - 1.2 V
Note 2
LED Forward Current IF - 25 mA Each LED

Note 1: The absolute maximum rating values of this product are not allowed to be exceeded
at any times. Should a module be used with any of the absolute maximum ratings
exceeded, the characteristics of the module may not be recovered, or in an extreme
case, the module may be permanently destroyed.
Note 2: VR Conditions: Zener Diode 20mA

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:6/20
3.1.1. Typical Operation Conditions

( Note 1)
Values
Item Symbol Unit Remark
Min. Typ. Max.

DVDD 3.0 3.3 3.6 V Note 2

AVDD (10.2) (10.4) (10.6) V

Power voltage
VGH (15.3) (16.0) (16.7) V

VGL (-7.7) (-7.0) (-6.3) V

Input signal voltage VCOM - TBD - V

Input logic high voltage VIH 0.7 DVDD - DVDD V

Note 3
Input logic low voltage VIL 0 - 0.3 DVDD V

Note 1: Be sure to apply DVDD and VGL to the LCD first, and then apply VGH.
Note 2: DVDD setting should match the signals output voltage (refer to Note 3) of
customers system board.
Note 3: DCLK,HS,VS,RESET,U/D, L/R,DE,R0~R7,G0~G7,B0~B7,MODE,DITHB.

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:7/20
3.1.2. Current Consumption

Values
Symbol Unit Remark
Item
Min. Typ. Max.

IGH - TBD - mA VGH =17.0V

IGL - TBD - mA VGL = -5.0V

Current for Driver
IDVDD - TBD - mA DVDD =3.3V

IAVDD - TBD - mA AVDD =10.4V

3.1.3. Backlight Driving Conditions

Values
Item Symbol Unit Remark
Min. Typ. Max.

Voltage for LED backlight VL (9.3) (9.9) (10.5) V Note 1

Current for LED backlight IL (170) (180) (200) mA

LED life time - 20,000 - - Hr Note 2

Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25 and
IL =180mA.

Note 2: The LED life time is defined as the module brightness decrease to 50% original
brightness at Ta=25 and IL =180mA. The LED lifetime could be decreased if
operating IL is lager than 180mA.

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:8/20
3.2. Power Sequence

a. Power on:

DVDDVGL
VGH
Data
B/L
b. Power off:

Data
B/L VGH
VGL
DVDD
Note: Data include R0~R7, B0~B7, GO~G7, U/D, L/R, DCLK, HS,VS,DE.

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:9/20
3.3. Timing Characteristics

3.3.1. AC Electrical Characteristics

Values
Item Symbol Unit Remark
Min. Typ. Max.

HS setup time Thst 8 - - ns

HS hold time Thhd 8 - - ns

VS setup time Tvst 8 - - ns

VS hold time Tvhd 8 - - ns

Data setup time Tdsu 8 - - ns

Data hole time Tdhd 8 - - ns

DE setup time Tesu 8 - - ns

DE hole time Tehd 8 - - ns

From 0 to 90%
DVDD Power On Slew rate TPOR - - 20 ms
DVDD
RESET pulse width TRst 1 - - ms

DCLK cycle time Tcoh 20 - - ns

DCLK pulse duty Tcwh 40 50 60 %

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:10/20
3.3.2. Data Input Format

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:11/20
3.3.3. Timing

Values
Item Symbol Unit Remark
Min. Typ. Max.

Horizontal Display Area thd - 800 - DCLK

DCLK Frequency fclk 26.4 33.3 46.8 MHz

One Horizontal Line th 862 1056 1200 DCLK

HS pulse width thpw 1 - 40 DCLK

HS Blanking thb 46 46 46 DCLK

HS Front Porch thfp 16 210 354 DCLK

Values
Item Symbol Unit Remark
Min. Typ. Max.

Vertical Display Area tvd - 480 - TH

VS period time tv 510 525 650 TH

VS pulse width tvpw 1 - 20 TH

VS Blanking tvb 23 23 23 TH

VS Front Porch tvfp 7 22 147 TH

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:12/20

4. Optical Specifications

Values
Item Symbol Condition Unit Remark
Min. Typ. Max.

L =180(9 oclock) 60 70 -

R =0(3 oclock) 60 70 -
Viewing angle
degree Note 1
(CR 10)
T =90(12 oclock) 40 50 -

B =270(6 oclock) 60 70 -

TON - 10 20 msec Note 3

Response time
TOFF - 15 30 msec Note 3

Contrast ratio CR 400 500 - - Note 4

WX Normal 0.26 0.31 0.36 - Note 2

==0
Color chromaticity Note 5
WY 0.28 0.33 0.38 - Note 6

Luminance L 200 250 - cd/m Note 6

Luminance
YU 70 75 - % Note 7
uniformity

Test Conditions:
1. DVDD=3.3V, IL=180mA (Backlight current), the ambient temperature is 25.
2. The test systems refer to Note 2.

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:13/20
Note 1: Definition of viewing angle range

Normal line
==0

=90
12 oclock direction

L
T R
B

=180 =0
Active Area

LCM

=270
Fig. 4-1 Definition of 6viewing
oclockangle
direction
Note 2: Definition of optical measurement system.
The optical characteristics should be measured in dark room. After 30 minutes
operation, the optical properties are measured at the center point of the LCD
screen. (Response time is measured by Photo detector TOPCON BM-7, other
items are measured by BM-5A/Field of view: 1 /Height: 500mm.)

Photo detector Normal line

==0

=90
12 oclock direction
500mm

=180 =0
Active Area

LCM

=270
6 oclock direction

Fig. 4-2 Optical measurement system setup

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:14/20
Note 3: Definition of Response time
The response time is defined as the LCD optical switching time interval between
White state and Black state. Rise time (TON) is the time between photo detector
output intensity changed from 90% to 10%. And fall time (TOFF) is the time
between photo detector output intensity changed from 10% to 90%.

White (TFT OFF) Black (TFT ON) White (TFT OFF)

Photo detector output

100%
(Relative value)

90%

10%
0%
TON TOFF

Fig. 4-3 Definition of response time

Note 4: Definition of contrast ratio

Luminance measured when LCD on the " White" state
Contrast ratio (CR) =
Luminance measured when LCD on the " Black" state

Note 5: Definition of color chromaticity (CIE1931)

Color coordinates measured at center point of LCD.

Note 6: All input terminals LCD panel must be ground while measuring the center area of
the panel. The LED driving condition is IL=180mA .

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:15/20

Note 7: Definition of Luminance Uniformity

Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every
measuring point is placed at the center of each measuring area.
B min
Luminance Uniformity (Yu) =
B max
L-------Active area length W----- Active area width

L
W/6

L/6 L/3 L/3

W/3
W

W/3

Fig. 4-4 Definition of measuring points

Bmax: The measured maximum luminance of all measurement position.

Bmin: The measured minimum luminance of all measurement position.

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:16/20

5. Reliability Test Items

(Note3)
Item Test Conditions Remark

High Temperature Storage Ta = 80 240hrs Note 1Note 4

Low Temperature Storage Ta = -30 240hrs Note 1Note 4

High Temperature Operation Ts = 70 240hrs Note 2Note 4

Low Temperature Operation Ta = -20 240hrs Note 1Note 4

Operate at High Temperature

+60, 90%RH 240hrs Note 4
and Humidity
-30/30 min ~ +80/30 min for a total 100
Thermal Shock cycles, Start with cold temperature and end Note 4
with high temperature.
Frequency range:10~55Hz
Stroke:1.5mm
Vibration Test Sweep:10Hz~55Hz~10Hz
2 hours for each direction of X. Y. Z.
(6 hours for total)

100G 6ms,X, Y, Z 3 times for each

Mechanical Shock
direction
Random Vibration :
0.015G*G/Hz from 5-200HZ, -6dB/Octave
Package Vibration Test from 200-500HZ
2 hours for each direction of X. Y. Z.
(6 hours for total)
Height:60 cm
Package Drop Test
1 corner, 3 edges, 6 surfaces

Electro Static Discharge 2KV, Human Body Mode, 100pF/1500

Note 1: Ta is the ambient temperature of samples.
Note 2: Ts is the temperature of panels surface.
Note 3: In the standard condition, there shall be no practical problem that may affect the
display function. After the reliability test, the product only guarantees operation,
but dont guarantee all of the cosmetic specification.
Note 4: Before cosmetic and function test, the product must have enough recovery time,
at least 2 hours at room temperature.

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:17/20

6. General Precautions
6.1. Safety

Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your
skin or clothes, wash it off immediately by using soap and water.

6.2. Handling

1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or to
excessive force on its surface.
2. The polarizer attached to the display is easily damaged. Please handle it carefully
to avoid scratch or other damages.
3. To avoid contamination on the display surface, do not touch the module surface
with bare hands.
4. Keep a space so that the LCD panels do not touch other components.
5. Put cover board such as acrylic board on the surface of LCD panel to protect panel
from damages.
6. Transparent electrodes may be disconnected if you use the LCD panel under
environmental conditions where the condensation of dew occurs.
7. Do not leave module in direct sunlight to avoid malfunction of the ICs.

6.3. Static Electricity

1. Be sure to ground module before turning on power or operating module.

2. Do not apply voltage which exceeds the absolute maximum rating value.

6.4. Storage

1. Store the module in a dark room where must keep at 2510 and 65%RH or less.
2. Do not store the module in surroundings containing organic solvent or corrosive
gas.
3. Store the module in an anti-electrostatic container or bag.

6.5. Cleaning

1. Do not wipe the polarizer with dry cloth. It might cause scratch.
2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals might
permanent damage to the polarizer.

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:18/20

7. Mechanical Drawing

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:19/20

8. Package Drawing

8.1. Packaging Material Table

Unit
Model
No. Item Dimensions(mm) Weight Quantity Remark
(Material)
(kg)
LCM
1 AT070TN92 164.9 100.0 5.7 TBD 50pcs
Module
BC Corrugated
2 Partition 512 349 226 1.466 1set
paper
Corrugated B Corrugated
3 510 350 0.071 4pcs
Paper paper
Corrugated B Corrugated
4 512 11 3 0.046 4pcs
Bar paper
Dust-Proof
5 PE 700 530 0.048 1pcs
Bag
6 A/S Bag PE 180 133 0.2 0.002 50pcs
Co rru ga t e d
7 Carton 530 355 255 1.100 1 pcs
pap e r
8 Total weight TBD

8.1 Packaging Quantity

Total LCM quantity in Carton: no. of Partition 2 Rows quantity per Row 25 = 50

The copyright belongs to InnoLux. Any unauthorized use is prohibited.

INNOLUX SPEC NO.: A070-92-TT-01 Date :2009/01/12
Page:20/20
8.2 Packaging Drawing

The copyright belongs to InnoLux. Any unauthorized use is prohibited.