Chapter 4

Beam Deflections

This chapter will discuss various methods to determine the deflection and slope at
the specific points in determinate beam. The methods include the Double
Integration method and Macaulay method as well as Moment Area method.

After successfully completing this chapter you should be able to:

Develop the general equation for the elastic curve of a deflected beam by
using double integration method and area-moment method.
State the boundary conditions of a deflected beam
Determine the deflections and slopes of elastic curves of simply supported
beams and cantilever beams.

4.1 Introduction

When a structure is placed under load it will bend, deflect or displace. The
deflection will depend on the following factors:

1. Geometry of the structure, including shape and flexural rigidity of

member.
2. Flexibility/rigidity of the material used.
3. Restraint of the supports.
4. Load pattern.

In the design of structures the primary requirement is to ensure that the structure
or structural component can adequately resist the loading to which it is being
subjected. This aspect of design is concerned with designing for strength.

However there are other aspects of design that are important, and in the case of
the design of beams another consideration is the value of the vertical deflections
that will occur when such beam is loaded. This chapter is intended as an
introduction to the analytical techniques used for calculating deflections in beams
and also for calculating the rotations at critical locations along the length of a
beam.

4.2 Deflection of Beams

The deformation of a beam is usually expressed in terms of its deflection from its
original unloaded position. The deflection is measured from the original neutral
surface of the beam to the neutral surface of the deformed beam. The

97
configuration assumed by the deformed neutral surface is known as the elastic
curve of the beam as shown in Figure 4.1.

Figure 4.1: Elastic curve

Numerous methods are available for the determination of beam deflections.
These methods include:

1. Double Integration Method

2. Moment Area Method
3. Strain Energy Method (Castiglianos Theorem)
4. Conjugate Beam Method
5. Method of Superposition

Of these methods, the first two are the ones that are commonly used. Therefore,
this chapter will be only focus on the first two methods.

4.3 Double Integration Method

The Double Integration Method, also known as Macaulays Method is a powerful

tool in solving deflection and slope of a beam at any point because we will be
able to get the equation of the elastic curve.

In calculus, the radius of curvature of a curve y = f(x) is given by

The radius of curvature of a beam is given as

Deflection of beams is so small, such that the slope of the elastic curve dy/dx is
very small, and squaring this expression the value becomes practically negligible,
hence

98
Thus, EI / M = 1 / y''

If EI is constant, the equation may be written as:

where x and y are the coordinates shown in the Figure 4.1 of the elastic curve of
the beam under load, y is the deflection of the beam at any distance x. E is the
modulus of elasticity of the beam, I represent the moment of inertia about the
neutral axis, and M represents the bending moment at a distance x from the end
of the beam. The product EI is called the flexural rigidity of the beam.

The first integration y' yields the slope of the elastic curve and the second
integration y gives the deflection of the beam at any distance x. The resulting
solution must contain two constants of integration since EI y" = M is of second
order. These two constants must be evaluated from known conditions concerning
the slope deflection at certain points of the beam. For instance, in the case of a
simply supported beam with rigid supports, at x = 0 and x = L, the deflection y = 0,
and in locating the point of maximum deflection, we simply set the slope of the
elastic curve y' to zero.

4.3.1 Boundary Conditions

dy
Generally, the deflections is known as y-values and slopes is known as . The
dx
values are called boundary conditions, which normally are:

1. For simply supported beams:

(i) At the x-values of the two supports, deflection is zero, i.e. y =
0.
(ii) If the point (i.e. the x-value) of maximum deflection is known,
dy
then at the x-value of the point, the slope is zero, i.e. = 0.
dx
2. For cantilever beams, at the x-value of the built-in end:
(i) The deflection is zero, i.e. y = 0.
dy
(ii) The slope is zero, i.e. = 0.
dx

99
Example 4.1

Determine the maximum deflection in a simply supported beam of length L

carrying a concentrated load P at midspan.

Solution:

At x = 0, y = 0, therefore, C2 = 0

At x = L, y = 0

Thus,

Maximum deflection will occur at x = L (midspan)

100
The negative sign indicates that the deflection is below the undeformed neutral
axis.

Therefore,

Example 4.2

Find the equation of the elastic curve for the cantilever beam shown in Fig. E4.2;
it carries a load that varies from zero at the wall to wo at the free end. Take the
origin at the wall.

Figure E4.2
Solution:

By ratio and proportion

101
At x = 0, y' = 0, therefore C1 = 0
At x = 0, y = 0, therefore C2 = 0

Therefore, the equation of the elastic curve is

Example 4.3

Compute the value of EI at midspan for the beam loaded as shown in Fig. E4.3.
If E = 10 GPa, what value of I is required to limit the midspan deflection to 1/360
of the span?

Figure E4.3

Solution:

102
At x = 0, y = 0, therefore C2 = 0
At x = 4 m, y = 0

Therefore,

At x = 2 m (midspan)

Maximum midspan deflection

Thus,

103
 or

Example 4.4

For the beam loaded as shown in Fig. E4.4, determine (a) the deflection and
slope under the load P and (b) the maximum deflection between the supports.

Figure E4.4

Solution:

104
At x = 0, y = 0, therefore C2 = 0
At x = a, y = 0

0 = -[ b / (6a) ] Pa3 + aC1

C1 = (ab/6)P

Therefore,

Part (a): Slope and deflection under the load P

Slope under the load P: (note x = a + b = L)

Deflection under the load P: (note x = a + b = L)

105
Part (b): Maximum deflection between the supports

The maximum deflection between the supports will occur at the point
where y' = 0.

At y' = 0, x - a do not exist thus,

At ,

106
Example 4.5

Determine the value of EIy midway between the supports for the beam loaded as
shown in Fig. E4.5.

Figure E4.5

Solution:

At x = 0, y = 0, therefore C2 = 0
At x = 6 m, y = 0

0 = 50(63) - 900(42) - (25/3)(24) + 6C1

107
C1 = 5600/9 Nm3

Therefore,

At x = 3 m

4.4 Moment Diagrams by Parts

The moment-area method of finding the deflection of a beam will demand the
accurate computation of the area of a moment diagram, as well as the moment of
such area about any axis. To pave its way, this section will deal on how to draw
moment diagrams by parts and to calculate the moment of such diagrams about
a specified axis.

4.4.1 Basic Principles

1. The bending moment caused by all forces to the left or to the right of any
section is equal to the respective algebraic sum of the bending moments
at that section caused by each load acting separately.

2. The moment of a load about a specified axis is always defined by the

equation of a spandrel

where n is the degree of power of x.

The graph of the above equation is as shown below

108
 and the area and location of centroid are defined as follows.

4.4.2 Cantilever Loadings

A = area of moment diagram

Mx = moment about a section of distance x
barred x = location of centoid
Degree = degree power of the moment diagram

Couple or Moment Load

Degree: zero

Concentrated Load

Degree: first

Uniformly Distributed Load

Degree: second

109
 Uniformly Varying Load

Degree: third

Example 4.6

For the beam loaded as shown in Fig. E4.6, compute the moment of area of the
M diagrams between the reactions about both the left and the right reaction.

Figure E4.6

Solution:

Moment diagram by parts can be drawn in different ways; three are shown below.

110
1st Solution:

2nd Solution:

111
Example 4.7

For the beam loaded as shown in Fig. E4.7, compute the moment of area of the
M diagrams between the reactions about both the left and the right reaction. (Hint:
Draw the moment diagram by parts from right to left.)

Figure E4.7

112
113
4.5 Area-Moment Method

Another method of determining the slopes and deflections in beams is the area-
moment method, which involves the area of the moment diagram.

4.5.1 Theorems of Area-Moment Method

Theorem I:

The change in slope between the tangents drawn to the elastic curve at any two
points A and B is equal to the product of 1/EI multiplied by the area of the
moment diagram between these two points.

Theorem II:

The deviation of any point B relative to the tangent drawn to the elastic curve at
any other point A, in a direction perpendicular to the original position of the beam,
is equal to the product of 1/EI multiplied by the moment of an area about B of that
part of the moment diagram between points A and B.

and

114
Rules of Sign:

1. The deviation at any point is positive if the point lies above the tangent,
negative if the point is below the tangent.

2. Measured from left tangent, if is counterclockwise, the change of slope is

positive, negative if is clockwise.

Example 4.8

The cantilever beam shown in Fig. E4.8 has a rectangular cross-section 50 mm

wide by h mm high. Find the height h if the maximum deflection is not to exceed
10 mm. Use E = 10 GPa.

Figure E4.8

Solution:

115
Example 4.9

For the cantilever beam shown in Fig. E4.9, what is the force (P) will cause zero
deflection at A?

Figure E 4.9

Solution:

116
Example 4.10

Compute the deflection and slope at a section 3 m from the wall for the beam
shown in Figure E4.10. Assume that E = 10 GPa and I = 30 106 mm4.

Figure E4.10

Solution:

117
Therefore:

4.6 Deflections in Simply Supported Beams Using Area-Moment Method

The deflection at some point B of a simply supported beam can be obtained by

the following steps.

1. Compute

2. Compute

3. Solve by ratio and proportion (see figure above).

118
Example 4.11

Compute the midspan value of EI for the beam shown in Fig. E4.11. (Hint: Draw
the M diagram by parts, starting from midspan toward the ends. Also take
advantage of symmetry to note that the tangent drawn to the elastic curve at
midspan is horizontal.)

Figure E4.11

Solution:

By symmetry:

From the figure,

119
Thus

Example 4.12

A simple beam supports a concentrated load placed anywhere on the span, as

shown in Fig. E4.12. Measuring x from A, show that the maximum deflection
occurs at x = [(L2 - b2)/3].

Figure E4.12

Solution:

120
From the figure:

121
Tutorial Problems

P4.1 A simply supported beam is loaded as shown in Fig. P4.1. Determine the
EIy value of the beam at point C.

Figure P4.1

Answer: -461.33 Nm3

P4.2 A simply supported beam, of diameter 12 mm, is loaded as shown in Fig.

P4.2. Using double integration method, determine the location of the
maximum deflection and magnitude of the deflection. Modulus of elasticity
is 200 GPa for the beam material.

Figure P4.2

Answer: -1.1263 mm at 0.9 m

P4.3 A cantilever beam AD carries a moment and a uniformly distributed load

as shown in Fig. P4.3. Determine the deflection at the free end A. Modulus
of elasticity is 200 GPa and I is 491 x 10-8 m4 for the beam.

Figure P4.3

122
 Answer: 2.35 mm
P4.4 A cantilever beam is loaded as illustrated in Fig. P4.4. Determine the
deflection at the free end. E = 200 GPa, I = 2.5 x 10-6 m4.

Figure P4.4

Answer: 4.99 mm

123