Export Unsecure PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 120

B R B R

R R R

Dd da Da D d da Da D d da Da

TIMKEN SNT PLUMMER BLOCK CATALOG


TIMKEN SNT PLUMMER
BLOCK CATALOG INDEX
Timken Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Housed Unit Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Shelf Life Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Engineering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SNT Plummer Block Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . 50
SNT Plummer Block Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
SNT Plummer Block Installation Guides . . . . . . . . . . . . . . . . . . . . . . 55
SNT Plummer Block Product Data Tables . . . . . . . . . . . . . . . . . . . . . 60
Spherical Roller Bearing Nomenclature . . . . . . . . . . . . . . . . . . . . . . 84
Spherical Roller Bearing Product Data Tables . . . . . . . . . . . . . . . . . 85
SNT Spherical Roller Bearing Metric Accessories . . . . . . . . . . . . . 93

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 1
TIMKEN
OVERVIEW

GROW STRONGER WITH TIMKEN


Every day, people around the world count on the strength of
Timken. Our expertise in metallurgy, friction management and
mechanical power transmission helps them accelerate
improvements in productivity and uptime.

We supply products and services that can help keep your


operations moving forward, whether you need drivetrain kits
for commercial vehicles, durable housings for bearings in dirty
environments, couplings that avoid metal-to-metal contact
between motors and gearboxes, repair services for rail
bearings, steel for an aircraft engine shaft, or other products
and services for your applications.

When you choose Timken, you receive more than high-quality


products and services: you gain a worldwide team of highly
trained and experienced Timken people committed to working
collaboratively with you to improve your business.

Globally, our 20,000 people provide reliable answers for a wide


range of operations in manufacturing, mining, medical
equipment, aerospace, transportation, oil and gas and other
diverse industries.

2 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
TIMKEN
OVERVIEW

INCREASE YOUR EQUIPMENT UPTIME


In addition to high-quality bearings, engineered steel and
mechanical power transmission components, we provide
valuable integrated products and services. For example, we
offer repair services and monitoring equipment that can alert
you to problems before they impact your uptime.

Additionally, we offer a broad selection of seals, premium


lubricants, lubricators, couplings and chain to keep your
operations moving smoothly.

Our 10 technology centers in the United States, Europe and


Asia help pioneer tomorrows innovations with extensive
basic and applied scientic research programs. Through
internal development and strategic acquisition of innovative
companies, we continue to expand our portfolio of highly
engineered bearings, steel and components.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 3
INTRODUCTION
HOUSED UNIT OVERVIEW

RUGGED TIMKEN HOUSED UNITS


HELP PROTECT YOUR BEARINGS
When you choose sturdy Timken housings, your bearings can
keep rolling smoothly, even in harsh environments impacted by
dirt, debris, water and other contaminants. Timken engineers
designed special housings to withstand tough challenges on
the job.
Protected inside durable cast iron, ductile iron or steel, our highly
engineered Timken ball and roller bearings work hard to help
you manufacture and transport materials, without excessive
maintenance due to contaminants.
Choose from our selection of housed units designed with ball,
tapered and spherical
sp bearings. Select enhancements like
Timken seals, lu
lubricants and housing covers best suited for each
engineers help you choose the right combination of
task. Our engin
and accessories to extend bearing life, increase
bearings an
and reduce maintenance costs.
uptime an
course, you can interchange existing products with
Of cou
Timken housed units because our bolt holes and shaft
Timke
centerline dimensions are designed to conform to
cen
industry standards.
ind
Timken housed units reect our strengths in
Ti
metallurgy,
m engineering and manufacturing. We
eensure that all our bearings meet the Timken
sstandard for quality.

4 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
INTRODUCTION
HOUSED UNIT OVERVIEW

TIMKEN SNT SPLIT PLUMMER BLOCKS CARRY


HEAVY LOADS
Timken SNT split plummer blocks are available in metric sizes. Their rugged cast iron, ductile
iron or cast steel designs stand up to a range of industrial environments. Our Timken SNT
plummer blocks have separate, matched caps and bases. In larger sizes where plummer blocks
are heavier, this split-block design eases installation. Remove the cap using a pry-tool slot for
bearing inspection, service and replacement.
Available in a variety of metric shaft sizes, Timken SNT plummer block units offer the choice
of tapered-bore design for easy mounting or straight-bore design for better axial location. The
block can be converted from xed to oat by adding or removing the locating rings. A variety
of sealing options help protect against contamination including all-purpose elastomer seals,
deection-type V-ring seals, precision labyrinth seals and heavy-duty taconite seals for highly
contaminated environments.

TYPICAL INDUSTRIES AND APPLICATIONS


Use Timken SNT plummer blocks in power generation (coal), mining, aggregate, cement, metals,
pulp, paper and other forestry operations, water treatment and food processing industries.
Applications include warehousing, conveyors, bulk material handling and industrial fans
and blowers.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 5
INTRODUCTION
HOUSED UNIT OVERVIEW

TIMKEN SAF SPLIT PILLOW BLOCKS HANDLE


HEAVY LOADS
Timken SAF split pillow blocks are available in imperial sizes. Their rugged cast iron, ductile
iron or cast steel designs stand up to a range of industrial environments. Our Timken SAF blocks
have separate, matched caps and bases. In larger sizes where pillow blocks are heavier, this
split-block design eases installation. Remove the cap using a pry-tool slot for bearing inspection,
service and replacement.
Available in a variety of imperial shaft sizes, Timken SAF units offer the choice of tapered-bore
design for easy mounting or straight-bore design for better axial location. The block can be
converted from xed to oat by removing the locating ring. Several sealing options protect against
contamination, including our standard seal, which is a precision aluminum triple-ring labyrinth seal.

TYPICAL INDUSTRIES AND APPLICATIONS


Use Timken SAF housed bearings in power generation (coal), mining, aggregate, cement,
metals, pulp, paper and other forestry operations, water treatment and food processing
industries. Applications include warehousing, conveyors, bulk material handling and industrial
fans and blowers.

6 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
INTRODUCTION

TIMKEN SPHERICAL ROLLER BEARING SOLID-BLOCK


HOUSED UNITS WITHSTAND HARSH CONDITIONS
Timken spherical roller bearing solid-block housed units stand up to rugged conditions. Composed
of solid steel, they withstand most falling debris and handle up to 1.5 degrees of misalignment.
The steel used in these products is up to two times stronger than cast iron, which may break or
pound out in tough applications.
Timken spherical roller bearing solid-block housed units come in ve locking congurations:
single and double set screws, eccentric locks for reversing applications, tapered-adaptor locks
and double-tapered locks.
Choose from three sealing options: labyrinth seals (for high-speed, high-temperature applications)
and triple-lip seals made of either nitrile or urethane. Timken steel auxiliary covers provide an
extra layer of protection, and they can be lled with Timken lubricants.

TYPICAL INDUSTRIES AND APPLICATIONS


Use Timken spherical roller bearing solid-block housed units in metals mills, aggregate and
cement, mining, power generation, agriculture, pulp, paper, sawmills and other forest industries.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 7
INTRODUCTION
HOUSED UNIT OVERVIEW

TIMKEN TYPE E HOUSED UNITS REPEL CONTAMINANTS,


ENHANCE PERFORMANCE
Timken Type E tapered roller bearing housed units feature double-lip seals and locking collars
that protect against water and other contaminants. This double-lip seal design blocks debris and
retains grease better than single-lip or triple-lip seals, according to Timken 2012 laboratory tests.
Its cast-iron exterior includes a corrosion-resistant electro-coat nish for the housing and collar
offering a more durable shield than industry-standard powder coating or black oxide. Set screws
with nylon patches reduce back-out, even in rigorous applications.
Premium Timken tapered roller bearings inside Type E housings are manufactured with advanced
technology that results in longer predicted useful bearing life than other housed units with standard
bearings. Designed with optimized bearing proles and improved surface nishes, Timken tapered
roller bearings operate efciently within the housing.

TYPICAL INDUSTRIES AND APPLICATIONS


Use Timken Type E housings for pulp and paper, power generation, mining, cement and aggregate
industries. Our Type E housed units also are widely used in equipment for air-handling and
treatment of water and waste water. Other common machine applications include mixers, washers,
shredders, mills and oven/furnace roller beds.

8 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
INTRODUCTION
HOUSED UNIT OVERVIEW

TIMKEN BALL HOUSED UNITS OFFER EASY


INSTALLATION, FLEXIBLE OPTIONS
Timken ball housed units, available in a variety of sizes and types, feature wide-inner-ring ball
bearings that provide additional shaft support and locking options. The Timken wide-inner-ring
ball bearing is designed for straight shafts and can be positioned without shoulders, locknuts
or adapters.
For easy installation, our ball housed units can be ordered pre-assembled with bearings, housings,
seals and locking systems. Choose from pillow blocks, anged cartridges, take-up units and
cylindrical cartridges. Our cast-iron, pressed-steel and other optional materials give you durable
choices for the exterior covers. Timken locking options include set screws, self-locking collars
and concentric collars.
Timken Shaft Guarding Technology deters set-screw damage to shafts by placing a hardened
band in the groove along the inner ring of the bearing. The set screws press against the band to
transfer gripping pressure onto the shaft, preventing nicks, as well as raised-metal or permanent
shaft damage. The stainless-steel band resists corrosion on the shaft. This system is particularly
helpful for applications where it would be expensive and time-consuming to replace shafts.

TYPICAL INDUSTRIES AND APPLICATIONS


Use Timken ball bearing housed units in agricultural applications, fans, blowers, food
processing devices and conveyors.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 9
TIMKEN
HOW TO USE THIS CATALOG

HOW TO USE THIS CATALOG


We designed this catalog to help you nd the Timken
housed units best suited to your specications.
Timken offers an extensive range of bearings and
accessories in both imperial and metric sizes. For
your convenience, size ranges are indicated in
millimeters and inches. Contact your Timken engineer
to learn more about our complete line for the special
needs of your application.
This publication contains dimensions, tolerances and
load ratings, as well as engineering sections describing
tting practices for shafts and housings, internal clearances,
materials and other bearing features. It provides valuable
assistance in the initial consideration of the type and
characteristics of the bearings that may best suit your
particular needs.
ISO and ANSI/ABMA, as used in this publication, refer to
the International Organization for Standardization and the
American National Standards Institute/American Bearing
Manufacturers Association.

Updates are made periodically to this catalog. Visit


www.timken.com for the most recent version of the Timken
SNT Plummer Block Catalog.

DISCLAIMER
This catalog is provided solely to give you analysis tools and data
to assist you in your product selection. Product performance is
affected by many factors beyond the control of Timken. Therefore,
you must validate the suitability and feasibility of all product
selections.
Timken products are sold subject to Timken terms and conditions
of sale, which include our limited warranty and remedy. You
can nd these at http://www.timken.com/en-us/purchase/Pages/
TermsandConditionsofSale.aspx.
Please consult with your Timken engineer for more information
and assistance.
Every reasonable effort has been made to ensure the accuracy of
the information in this writing, but no liability is accepted for errors,
omissions or for any other reason.

10 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
TIMKEN
SHELF LIFE AND STORAGE OF GREASE-LUBRICATED BEARINGS AND COMPONENTS

SHELF LIFE AND STORAGE OF European REACH Compliance


GREASE-LUBRICATED BEARINGS Timken lubricants, greases and similar products sold in
AND COMPONENTS standalone containers or delivery systems are subject to the
European REACH (Registration, Evaluation, Authorization
To help you get the most value from our products, Timken
and Restriction of CHemicals) directive. For import into the
provides guidelines for the shelf life of grease-lubricated
European Union, Timken can sell and provide only those
ball and roller bearings, components and assemblies. Shelf
lubricants and greases that are registered with ECHA
life information is based on Timken and industry test data
(European CHemical Agency). For further information, please
and experience.
contact your Timken engineer.

SHELF LIFE POLICY


Shelf life should be distinguished from lubricated bearing/
component design life as follows:

Shelf life of the grease-lubricated bearing/component


represents the period of time prior to use or installation.

The shelf life is a portion of the anticipated aggregate


design life. It is impossible to accurately predict design
life due to variations in lubricant bleed rates, oil migration,
operating conditions, installation conditions, temperature,
humidity and extended storage.

Shelf life values, available from Timken, represent a


maximum limit and assume adherence to the storage
and handling guidelines suggested in this catalog or by a
Timken associate. Deviations from the Timken storage and
handling guidelines may reduce shelf life. Any specication
or operating practice that denes a shorter shelf life should
be used.
Timken cannot anticipate the performance of the grease
lubricant after the bearing or component is installed or placed
in service.

TIMKEN IS NOT RESPONSIBLE FOR THE SHELF LIFE


OF ANY BEARING/COMPONENT LUBRICATED BY
ANOTHER PARTY.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 11
TIMKEN
SHELF LIFE AND STORAGE OF GREASE-LUBRICATED BEARINGS AND COMPONENTS

STORAGE
Timken suggests the following storage guidelines for our
nished products (bearings, components and assemblies,
referred to as products):

Unless directed otherwise by Timken, products should be


kept in their original packaging until they are ready to be
placed into service.

Do not remove or alter any labels or stencil markings on the


packaging.

Products should be stored in such a way that the packaging


is not pierced, crushed or otherwise damaged.

After a product is removed from its packaging, it should be


placed into service as soon as possible.

When removing a product that is not individually packaged


from a bulk pack container, the container should be
resealed immediately after the product
is removed.

Do not use product that has exceeded its shelf life as


dened in the Timken shelf life guidelines statement.

The storage area temperature should be maintained


between 0 C (32 F) and 40 C (104 F); temperature
uctuations should be minimized.

The relative humidity should be maintained below 60


percent and the surfaces should be dry.

The storage area should be kept free from airborne


contaminants such as, but not limited to, dust, dirt, harmful
vapors, etc.

The storage area should be isolated from undue vibration.

Extreme conditions of any kind should be avoided.

Due to the fact that Timken is not familiar with your particular
storage conditions, we strongly suggest following these
guidelines. However, you may be required by circumstances
or applicable government requirements to adhere to stricter
storage requirements.

12 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
TIMKEN
SHELF LIFE AND STORAGE OF GREASE-LUBRICATED BEARINGS AND COMPONENTS

Most bearing components typically ship protected


with a corrosion-preventive compound that is not
a lubricant. These components may be used in
oil-lubricated applications without removal of the
corrosion-preventive compound. When using
some specialized grease lubrications, we advise
you to remove the corrosion-preventive compound
before packing the bearing components with
suitable grease.
Be careful in selecting lubrication, however, since
different lubricants are often incompatible.
When you receive a bearing or plummer block shipment,
do not remove products from their packaging until they
are ready for mounting so they do not become corroded or
contaminated.
Store bearings and bearing housings in an appropriate
atmosphere so they remain protected for the intended period.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 13
TIMKEN
WARNINGS AND CAUTIONS

WARNING NOTE
Failure to observe the following warnings Do not use excessive force when mounting or
could create a risk of death or serious injury. dismounting the unit.
Follow all tolerance, t, and torque recommendations.
Proper maintenance and handling practices are critical. Always follow the Original Equipment Manufacturers
Failure to follow selection recommendations and installation and maintenance guidelines.
installation instructions and to maintain proper lubrication
Ensure proper alignment.
can result in equipment failure.
Never weld housed units.
Overheated bearings can ignite explosive atmospheres.
Special care must be taken to properly select, install, Do not heat components with an open ame.
maintain, and lubricate housed unit bearings that are Do not operate at bearing temperatures above 121 C (250 F).
used in or near atmospheres that may contain explosive
levels of combustible gases or accumulations of dust such
from grain, coal, or other combustible materials. Consult
your equipment designer or supplier for installation and
maintenance instructions.
If hammer and bar are used for installation or removal of a
part, use a mild steel bar (e.g., 1010 or 1020 grade). Mild steel
bars are less likely to cause release of high-speed fragments
from the hammer, bar or the part being removed.

CAUTION
Failure to follow these cautions
may result in property damage.

Do not use damaged housed units.

Warnings for this product line are in this catalog and posted
on www.timken.com/warnings.

14 TIMKEN HOUSED UNIT CATALOG Download 3D Models and 2D Drawings at cad.timken.com


SNT SPLIT PLUMMER BLOCKS

TIMKEN SNT SPLIT PLUMMER


BLOCKS DELIVER PERFORMANCE
The Timken SNT plummer blocks metric product line is available
with a variety of components and accessories that allow for
customizable solutions. SNT split plummer blocks are available
in rugged cast iron, ductile iron or cast steel to match a range
of industrial environments and applications. Our Timken SNT
plummer blocks have separate, matched caps and bases. These
housings feature multiple design attributes to ease installation,
including center marks for easier alignment and dimples for
positioning pins and mounting bolt holes. Remove the cap using
a pry-tool slot for bearing inspection, service and replacement.
Available in a variety of shaft sizes, Timken SNT plummer blocks
offer the choice of tapered-bore design for easy mounting or a
straight-bore design for better axial location. The block can be
converted from xed to oat by adding or removing locating rings.
Sealing options for the Timken SNT include double-lip, labyrinth,
V-ring and taconite designs.

TYPICAL INDUSTRIES AND APPLICATIONS


Common uses include processing and material handling
equipment found in many industries, including power generation
(coal), mining, aggregate, cement, metal mills, pulp, paper and
other forestry operations, water treatment and food processing.
Applications include conveyors, bulk material handling, industrial
fans and blowers.

Engineering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SNT Plummer Block Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . 50
SNT Plummer Block Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
SNT Plummer Block Installation Guides . . . . . . . . . . . . . . . . . . . . . . 55
SNT Plummer Block Product Data Tables . . . . . . . . . . . . . . . . . . . . . 60
Spherical Roller Bearing Nomenclature . . . . . . . . . . . . . . . . . . . . . . 84
Spherical Roller Bearing Product Data Tables . . . . . . . . . . . . . . . . . 85
SNT Spherical Roller Bearing Metric Accessories . . . . . . . . . . . . . 93
Updates are made periodically to this catalog. Visit
www.timken.com for the most recent version of the Timken
SNT Plummer Block Catalog (order no. 10624).

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 15
SNT SPLIT PLUMMER BLOCKS
ENGINEERING

16 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING

ENGINEERING
The following topics are covered within this engineering section:
n:
Spherical roller bearing design types.
Shaft tting practice and mounting recommendations.
This engineering section is not intended to be comprehensive,
e,
but does serve as a useful guide in spherical roller bearing
and SNT plummer block housing selection.
To view the complete engineering catalog, please visit
www.timken.com. To order the catalog, please contact
your Timken engineer and request a copy of the Timken
Engineering Manual (order no. 10424).

Radial Spherical Roller Bearing Types and Cages . . . . . . . . . . . 18


Metric System Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Spherical Roller Bearing Mounting, Fitting,
Setting and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Shaft Fits for Cylindrical Bore Bearings . . . . . . . . . . . . . . . . . . . . 29
Fitting Practice Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 17
SNT SPLIT PLUMMER BLOCKS
ENGINEERING RADIAL SPHERICAL ROLLER BEARING TYPES AND CAGES METRIC SYSTEM TOLERANCES

RADIAL SPHERICAL ROLLER BEARING TYPES AND CAGES


The principle styles of radial spherical roller bearings that Timken operating temperatures compared to the previous offering.
offers are: In addition to these improvements, cage designs vary between
600 mm O.D.: EJ, EM and EMB the different styles as noted below.
600 mm O.D.: YMB
Style Cage Design
Above sufxes correspond to different types of designs depending EJ Land-riding steel cage; one per row
on bearing size and geometry. The main difference is the cage
EM Roller-riding one-piece brass cage
design used in the assembly. Spherical roller bearings with an
EMB/YMB Land-riding one-piece brass cage
EJ cage sufx are tted with a stamped-steel cage. YM/EM/YMB
sufxes are used with brass cage designs. Most Timken spherical roller bearings are available with a
cylindrical bore as well as a tapered bore. Tapered bore bearing
The newly redesigned Timken EJ, EM and EMB bearings offer
part numbers are designated with a K sufx.
higher load ratings, increased thermal speed ratings and reduced

METRIC SYSTEM TOLERANCES


Spherical roller bearings are manufactured to a number of bearing lines. For the purposes of this catalog, ISO specications
specications, with each having classes that dene tolerances are shown for spherical roller bearings.
on dimensions such as bore, O.D., width and runout. Metric Boundary dimension tolerances for spherical roller bearing
bearings have been manufactured to corresponding standard usage are listed in the following tables. These tolerances are
negative tolerances. provided for use in selecting bearings for general applications,
The following table summarizes the different specications and in conjunction with the bearing mounting and tting practices
classes for spherical roller bearings and other available Timken offered in later sections.

TABLE 1. BEARING SPECIFICATIONS AND CLASSES

System Specication Bearing Type Standard Bearing Class Precision Bearing Class
Metric ISO/DIN All Bearing Types P0 P6 P5 P4 P2
Imperial ABMA Spherical RBEC 1 RBEC 3 RBEC 5 RBEC 7 RBEC 9

18 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING METRIC SYSTEM TOLERANCES

Standard Timken radial spherical roller bearings maintain The term deviation is dened as the difference between a single
normal tolerances according to ISO 492. Tables 2 and 3 list ring dimension and the nominal dimension. For metric tolerances,
the critical tolerances for these bearing types. Timken SNT the nominal dimension is at a +0 mm tolerance. The deviation is
housings are used with bearings that conform to ISO P0, or the tolerance range for the listed parameter. Variation is dened
standard tolerances. as the difference between the largest and smallest measurements
of a given parameter for an individual ring.

TABLE 2. SPHERICAL ROLLER BEARING TOLERANCES INNER RING (METRIC)(1)


Face
Axial Width Deviation Inner
Bore Deviation(2) Width Variation Radial Runout Runout
Bearing Bore Runout & Outer Rings(2)
dmp VBS Kia with Bore
Sia Bs and Cs
Sd
Over Incl. P0 P6 P5 P0 P6 P5 P0 P6 P5 P5 P5 P0, P6 P5
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in. in. in. in. in.
2.5000 10.000 -0.008 -0.007 -0.005 0.015 0.015 0.005 0.010 0.006 0.004 0.007 0.007 -0.120 -0.040
0.0984 0.3937 -0.0003 -0.0003 -0.0002 0.0006 0.0006 0.0002 0.0004 0.0002 0.0002 0.0003 0.0003 -0.0047 -0.0157
10.000 18.000 -0.008 -0.007 -0.005 0.020 0.020 0.005 0.010 0.007 0.004 0.007 0.007 -0.120 -0.080
0.3937 0.7087 -0.0003 -0.0003 -0.0002 0.0008 0.0008 0.0002 0.0004 0.0003 0.0002 0.0003 0.0003 -0.0047 -0.0031
18.000 30.000 -0.010 -0.008 -0.006 0.020 0.020 0.005 0.013 0.008 0.004 0.008 0.008 -0.120 -0.120
0.7087 1.1811 -0.0004 -0.0003 -0.0002 0.0008 0.0008 0.0002 0.0005 0.0003 0.0002 0.0003 0.0003 -0.0047 -0.0047
30.000 50.000 -0.012 -0.010 -0.008 0.020 0.020 0.005 0.015 0.010 0.005 0.008 0.008 -0.120 -0.120
1.1811 1.9685 -0.0005 -0.0004 -0.0003 0.0008 0.0008 0.0002 0.0006 0.0004 0.0002 0.0003 0.0003 -0.0047 -0.0047
50.000 80.000 -0.015 -0.012 -0.009 0.025 0.025 0.006 0.020 0.010 0.005 0.008 0.008 -0.150 -0.150
1.9685 3.1496 -0.0006 -0.0005 -0.0004 0.0010 0.0010 0.0002 0.0008 0.0004 0.0002 0.0003 0.0003 -0.0059 -0.0059
80.000 120.000 -0.020 -0.015 -0.010 0.025 0.025 0.007 0.025 0.013 0.006 0.009 0.009 -0.200 -0.200
3.1496 4.7244 -0.0008 -0.0006 -0.0004 0.0010 0.0010 0.0003 0.0010 0.0005 0.0002 0.0004 0.0004 -0.0079 -0.0079
120.000 150.000 -0.025 -0.018 -0.013 0.030 0.030 0.008 0.030 0.018 0.008 0.010 0.010 -0.250 -0.250
4.7244 5.9055 -0.0010 -0.0007 -0.0005 0.0012 0.0012 0.0003 0.0012 0.0007 0.0003 0.0004 0.0004 -0.0098 -0.0098
150.000 180.000 -0.025 -0.018 -0.013 0.030 0.030 0.008 0.030 0.018 0.008 0.010 0.010 -0.250 -0.250
5.9055 7.0866 -0.0010 -0.0007 -0.0005 0.0012 0.0012 0.0003 0.0012 0.0007 0.0003 0.0004 0.0004 -0.0098 -0.0098
180.000 250.000 -0.030 -0.022 -0.015 0.030 0.030 0.010 0.040 0.020 0.010 0.011 0.013 -0.300 -0.300
7.0866 9.8425 -0.0012 -0.0009 -0.0006 0.0012 0.0012 0.0004 0.0016 0.0008 0.0004 0.0004 0.0005 -0.0018 -0.0018
250.000 315.000 -0.035 -0.025 -0.018 0.035 0.035 0.013 0.050 0.025 0.013 0.013 0.015 -0.350 -0.350
9.8425 12.4016 -0.0014 -0.0010 -0.0007 0.0014 0.0014 0.0005 0.0020 0.0010 0.0005 0.0005 0.0006 -0.0138 -0.0138
315.000 400.000 -0.040 -0.030 -0.023 0.040 0.040 0.015 0.060 0.030 0.015 0.015 0.020 -0.400 -0.400
12.4016 15.7480 -0.0016 -0.0012 -0.0009 0.0016 0.0016 0.0006 0.0024 0.0012 0.0006 0.0006 0.0008 -0.0157 -0.0157
400.000 500.000 -0.045 -0.035 0.050 0.045 0.065 0.035 -0.450

15.7480 19.6850 -0.0018 -0.0014 0.0020 0.0018 0.0026 0.0014 -0.0177
500.000 630.000 -0.050 -0.040 0.060 0.050 0.070 0.040 -0.500

19.6850 24.8031 -0.0020 -0.0016 0.0024 0.0020 0.0028 0.0016 -0.0197
630.000 800.000 -0.075 0.070 0.080 -0.750

24.8031 31.4961 -0.0030 0.0028 0.0031 -0.0295
(1)
Symbol denitions are found on pages 32-33 of the Timken Engineering Manual (order no. 10424).
(2)
Tolerance range is from +0 to value listed.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 19
SNT SPLIT PLUMMER BLOCKS
ENGINEERING METRIC SYSTEM TOLERANCES

TABLE 3. SPHERICAL ROLLER BEARING TOLERANCES OUTER RING (METRIC)(1)


Outside
Axial Diameter
Bearing O.D. Outside Deviation (2)
Width Variation Radial Runout
Runout Runout
With Face
Dmp VCS Kea Sea SD

Over Incl. P0 P6 P5 P0 P6 P0 P6 P5 P5 P5
mm mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in. in.

0.000 18.000 -0.008 -0.007 -0.005 0.015 0.005 0.015 0.008 0.005 0.008 0.008
0.0000 0.7087 -0.0003 -0.0003 -0.0002 0.0006 0.0002 0.0006 0.0003 0.0002 0.0003 0.0003
18.000 30.000 -0.009 -0.008 -0.006 0.020 0.005 0.015 0.009 0.006 0.008 0.008
0.7087 1.1811 -0.0004 -0.0003 -0.00024 0.0008 0.0002 0.0006 0.0004 0.00024 0.0003 0.0003
30.000 50.000 -0.011 -0.009 -0.007 0.020 0.005 0.020 0.010 0.007 0.008 0.008
1.1811 1.9685 -0.0004 -0.0004 -0.0003 0.0008 0.0002 0.0008 0.0004 0.0003 0.0003 0.0003
50.000 80.000 -0.013 -0.011 -0.009 0.025 0.006 0.025 0.013 0.008 0.010 0.008
1.9685 3.1496 -0.0005 -0.0004 -0.0004 0.0010 0.00024 0.0010 0.0005 0.0003 0.0004 0.0003
80.000 120.000 -0.015 -0.013 -0.010 0.025 0.008 0.035 0.018 0.010 0.011 0.009
3.1496 4.7244 -0.0006 -0.0005 -0.0004 0.0010 0.0003 0.0014 0.0007 0.0004 0.0004 0.0004
120.000 150.000 -0.018 -0.015 -0.011 0.030 0.008 0.040 0.020 0.011 0.013 0.010
4.7244 5.9055 -0.0007 -0.0006 -0.0004 0.0012 0.0003 0.0016 0.0008 0.0004 0.0005 0.0004
150.000 180.000 -0.025 -0.018 -0.013 0.030 0.008 0.045 0.023 0.013 0.014 0.010
5.9055 7.0866 -0.0010 -0.0007 -0.0005 0.0012 0.0003 0.0018 0.0009 0.0005 0.0006 0.0004
180.000 250.000 -0.030 -0.020 -0.015 0.030 0.010 0.050 0.025 0.015 0.015 0.011
7.0866 9.8425 -0.0012 -0.0008 -0.0006 0.0012 0.0004 0.0020 0.0010 0.0006 0.0006 0.0004
250.000 315.000 -0.035 -0.025 -0.018 0.035 0.011 0.060 0.030 0.018 0.018 0.013
9.8425 12.4016 -0.0014 -0.0010 -0.0007 0.0014 0.0004 0.0024 0.0012 0.0007 0.0007 0.0005
315.000 400.000 -0.040 -0.028 -0.020 0.040 0.013 0.070 0.035 0.020 0.020 0.013
12.4016 15.7480 -0.0016 -0.0011 -0.0008 0.0016 0.0005 0.0028 0.0014 0.0008 0.0008 0.0005
400.000 500.000 -0.045 -0.033 -0.023 0.045 0.015 0.080 0.040 0.023 0.023 0.015
15.7480 19.6850 -0.0018 -0.0013 -0.0009 0.0018 0.0006 0.0031 0.0016 0.0009 0.0009 0.0006
500.000 630.000 -0.050 -0.038 -0.028 0.050 0.018 0.100 0.050 0.025 0.025 0.018
19.6850 24.8031 -0.0020 -0.0015 -0.0011 0.0020 0.0007 0.0039 0.0020 0.0010 0.0010 0.0007
630.000 800.000 -0.075 -0.045 -0.035 0.020 0.120 0.060 0.030 0.030 0.020

24.8031 31.4961 -0.0030 -0.0018 -0.0014 0.0008 0.0047 0.0024 0.0012 0.0012 0.0008
800.000 1000.000 -0.100 -0.060 0.140 0.075

31.4961 39.3701 -0.0040 -0.0024 0.0055 0.0030
1000.000 1250.000 -0.125 0.160

39.3701 49.2126 -0.0050 0.0063
(1)
Symbol denitions are found on pages 32-33 of the Timken Engineering Manual (order no. 10424).
(2)
Tolerance range is from +0 to value listed.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

20 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING MOUNTING, FITTING, SETTING AND INSTALLATION

SPHERICAL ROLLER BEARING MOUNTING, FITTING, SETTING


AND INSTALLATION
MOUNTING
Typically, spherical roller bearings are mounted in combination The suggested t symbols are in accordance with ISO 286. For
with another spherical roller bearing or a cylindrical roller bearing. help with suggested tting practice, contact your Timken engineer.
With spherical roller bearings, typically one bearing is xed axially As a general guideline, rotating inner rings should be applied with
and the other is mounted with loose ts and axial clearance. This an interference t. Loose ts may permit the inner rings to creep or
allows axial movement or oat for environmental conditions such turn, and wear the shaft and the backing shoulder. This wear may
as uneven thermal growth between shaft and housing. In SNT result in excessive bearing looseness and possible bearing and shaft
housings, two or more locating rings can be used. With these damage. Additionally, abrasive metal particles resulting from creep or
ring(s) installed, a xed bearing is achieved. When the ring(s) turning may enter into the bearing and cause damage and vibration.
are removed, and provided the bearing is properly located in the The load conditions and bearing envelope dimensions should be
housing, the bearing can oat freely. used to select the suggested shaft t from the tables.
Fig. 1 shows a xed split housing with a locating ring installed Contact your Timken engineer if you require the specic t
and a oat bearing without the locating ring. practice used for a given SNT housing.

FITTING PRACTICE
WARNING
Tables 6 through 8 on pages 29 through 35 list the recommended
tting practice for spherical roller bearing inner rings on shafts. Failure to observe the following warnings
The tables assume: could create a risk of death or serious injury.
The bearing is of normal precision.
Proper maintenance and handling practices are critical.
The shaft is solid and made from steel. Always follow installation instructions and
The bearing seats are ground or turned to less than maintain proper lubrication.
approximately 1.6 Ra nish.
Overheated bearings can ignite explosive atmospheres.
Special care must be taken to properly select, install,
maintain, and lubricate housed unit bearings that are used
in or near atmospheres that may contain explosive levels
of combustible gases or accumulations of dust such as
from grain, coal, or other combustible materials. Consult
your equipment designer or supplier for installation and
maintenance instructions.

Float Fixed

Fig. 1. Split housing showing xed and oat mounting.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 21
SNT SPLIT PLUMMER BLOCKS
ENGINEERING MOUNTING, FITTING, SETTING AND INSTALLATION

TAPERED BORE DESIGNS SETTING


Typically, tapered bore bearings are selected to simplify shaft To achieve appropriate operating clearance, attention must be
mounting and dismounting. Since the spherical roller bearing is paid to the effects that tting practice and thermal gradients
not separable, mounting can be simplied by use of an adapter have within the bearing.
sleeve with a cylindrical bore and tapered O.D. A tapered bore
roller bearing also can be mounted directly onto a tapered shaft. FITTING PRACTICE
An interference t between the inner ring and a solid steel
shaft will reduce the radial clearance within the bearing by
approximately 80 percent of the t.

NOTE
It is critical to select the RIC that allows for this reduction.

Spherical roller bearings with a tapered bore require


a slightly greater interference t on the shaft than a
cylindrical bore bearing.

THERMAL GRADIENTS
Thermal gradients within the bearing are primarily
a function of the bearing rotational speed. As speed
increases, thermal gradients increase, thermal growth
Fig. 2. Spherical roller bearing mounted with an adapter sleeve. occurs and the radial clearance is reduced.

Bearings with a tapered bore typically require a tighter t on


As a rule of thumb, radial clearance should be increased for
speeds in excess of 70 percent of the speed rating.
the shaft than bearings with a cylindrical bore. A locknut is
typically used to drive the inner ring up a tapered shaft sleeve. For help selecting the correct radial internal clearance for your
The locknut position is then secured by use of a lockwasher or application, consult with your Timken engineer.
lockplate. Timken offers a wide range of accessories to ease Radial internal clearance tolerances are listed in tables 4 and 5
the assembly of spherical roller bearings with a tapered bore for spherical roller bearings.
(see page 25). For approximating the clearance loss for axial Spherical roller bearings are ordered with a specied standard
drive-up, an 85 percent radial loss approximation can be used. or non-standard radial internal clearance value. The standard
That is, the radial clearance loss per axial drive-up can roughly be radial internal clearances are designated as C2, C0 (normal), C3,
approximated as 71 m/mm for a 1:12 tapered. Table 5 on page 24 C4 or C5 and are in accordance with ISO 5753. C2 represents the
provides a direct relation between suggested RIC (radial internal minimum clearance and C5 represents the maximum clearance.
clearance) reduction due to installation and the corresponding Non-standardized values also are available by special request.
axial displacement of the inner ring.
The clearance required for a given application depends on the
desired operating precision, the rotational speed of the bearing,
and the tting practice used. SNT housings are commonly used
with C0 or C3 clearance bearing, though other clearances may
be ordered for specic applications. Typically, larger clearance
reduces the operating load zone of the bearing, increases the
maximum roller load, and reduces the bearings expected life.
However, a spherical roller bearing that has been put into a
preload condition can experience premature bearing damage
caused by excessive heat generation and/or material fatigue. As
a general guideline, spherical roller bearings should not operate
in a preloaded condition.

22 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING MOUNTING, FITTING, SETTING AND INSTALLATION

TABLE 4. RADIAL INTERNAL CLEARANCE LIMITS SPHERICAL ROLLER BEARINGS CYLINDRICAL BORE
Cylindrical Bore
Normal Typical Reduction Typical
Bore C4
CO of RIC RIC After
(Nominal)
Min. Max. Min. Max. Due to Installation Installation
C2 C3 C5
Over Incl. Min. Max. Min. Max. Min. Max. Min. Max. Min.
mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in.
20 30 0.015 0.025 0.04 0.055 0.075 0.095 0.015 0.02 0.015
0.9449 1.1811 0.0006 0.001 0.0016 0.0022 0.003 0.0037 0.0006 0.0008 0.0006
30 40 0.015 0.03 0.045 0.06 0.08 1 0.02 0.025 0.015
1.1811 1.5748 0.0006 0.0012 0.0018 0.0024 0.0031 0.0039 0.0008 0.001 0.0006
40 50 0.02 0.035 0.055 0.075 0.1 0.125 0.025 0.03 0.02
1.5748 1.9685 0.0008 0.0014 0.0022 0.003 0.0039 0.0049 0.001 0.0012 0.0008
50 65 0.02 0.04 0.065 0.09 0.12 0.15 0.03 0.038 0.025
1.9685 2.5591 0.0008 0.0016 0.0026 0.0035 0.0047 0.0059 0.0012 0.0015 0.001
65 80 0.03 0.05 0.08 0.11 0.145 0.18 0.038 0.051 0.025
2.5591 3.1496 0.0012 0.002 0.0031 0.0043 0.0057 0.0071 0.0015 0.002 0.001
80 100 0.035 0.06 0.1 0.135 0.18 0.225 0.046 0.064 0.036
3.1496 3.9370 0.0014 0.0024 0.0039 0.0053 0.0071 0.0089 0.0018 0.0025 0.0014
100 120 0.04 0.075 0.12 0.16 0.21 0.26 0.051 0.071 0.051
3.9370 4.7244 0.0016 0.003 0.0047 0.0063 0.0083 0.0102 0.002 0.0028 0.002
120 140 0.05 0.095 0.145 0.19 0.24 0.3 0.064 0.089 0.056
4.7244 5.5118 0.002 0.0037 0.0057 0.0075 0.0094 0.0118 0.0025 0.0035 0.0022
140 160 0.06 0.11 0.17 0.22 0.28 0.35 0.076 0.102 0.056
5.5118 6.2992 0.0024 0.0043 0.0067 0.0087 0.011 0.0138 0.003 0.004 0.0022
160 180 0.065 0.12 0.18 0.24 0.31 0.39 0.076 0.114 0.061
6.2992 7.0866 0.0026 0.0047 0.0071 0.0094 0.0122 0.0154 0.003 0.0045 0.0024
180 200 0.07 0.13 0.2 0.26 0.34 0.43 0.089 0.127 0.071
7.0866 7.8740 0.0028 0.0051 0.0079 0.0102 0.0134 0.0169 0.0035 0.005 0.0028
200 225 0.08 0.14 0.22 0.29 0.38 0.47 0.102 0.14 0.076
7.8740 8.8582 0.0031 0.0055 0.0087 0.0114 0.015 0.0185 0.004 0.0055 0.003
225 250 0.09 0.15 0.24 0.32 0.42 0.52 0.114 0.152 0.089
8.8582 9.8425 0.0035 0.0059 0.0094 0.0126 0.0165 0.0205 0.0045 0.006 0.0035
250 280 0.1 0.17 0.26 0.35 0.46 0.57 0.114 0.165 0.102
9.8425 11.0236 0.0039 0.0067 0.0102 0.0138 0.0181 0.0224 0.0045 0.0065 0.004
280 315 0.11 0.19 0.28 0.37 0.5 0.63 0.127 0.178 0.102
11.0236 12.4016 0.0043 0.0075 0.011 0.0146 0.0197 0.0248 0.005 0.007 0.004
315 355 0.12 0.2 0.31 0.41 0.55 0.69 0.14 0.19 0.114
12.4016 13.9764 0.0047 0.0079 0.0122 0.0161 0.0217 0.0272 0.0055 0.0075 0.0045
355 400 0.13 0.22 0.34 0.45 0.6 0.75 0.152 0.203 0.127
13.9764 15.7480 0.0051 0.0087 0.0134 0.0177 0.0236 0.0295 0.006 0.008 0.005
400 450 0.14 0.24 0.37 0.5 0.66 0.82 0.165 0.216 0.152
15.7480 17.7165 0.0055 0.0094 0.0146 0.0197 0.026 0.0323 0.0065 0.0085 0.006
450 500 0.14 0.26 0.41 0.55 0.72 0.9 0.178 0.229 0.165
17.7165 19.6850 0.0055 0.0102 0.0161 0.0217 0.0283 0.0354 0.007 0.009 0.0065
500 560 0.15 0.28 0.44 0.6 0.78 1 0.203 0.254 0.178
19.6850 22.0472 0.0059 0.011 0.0173 0.0236 0.0307 0.0394 0.008 0.01 0.007
560 630 0.17 0.31 0.48 0.65 0.85 1.1 0.229 0.279 0.203
22.0472 24.8031 0.0067 0.0122 0.0189 0.0256 0.0335 0.0433 0.009 0.011 0.008
630 710 0.19 0.35 0.53 0.7 0.92 1.19 0.254 0.305 0.203
24.8031 27.9528 0.0075 0.0138 0.0209 0.0276 0.0362 0.0469 0.01 0.012 0.008
710 800 0.21 0.39 0.58 0.77 1.01 1.3 0.279 0.356 0.229
27.9528 31.4961 0.0083 0.0154 0.0228 0.0303 0.0398 0.0512 0.011 0.014 0.009
800 900 0.23 0.43 0.65 0.86 1.12 1.44 0.305 0.381 0.252
31.4961 35.4331 0.0091 0.0169 0.0256 0.0339 0.0441 0.0567 0.012 0.015 0.01
900 1000 0.26 0.48 0.71 0.93 1.22 1.57 0.356 0.432 0.279
35.4331 39.3701 0.0102 0.0189 0.028 0.0366 0.048 0.0618 0.014 0.017 0.011
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 23
SNT SPLIT PLUMMER BLOCKS
ENGINEERING MOUNTING, FITTING, SETTING AND INSTALLATION

TABLE 5. RADIAL INTERNAL CLEARANCE LIMITS SPHERICAL ROLLER BEARINGS TAPERED BORE
Tapered Bore Suggested Axial Displacement
Normal Reduction of Inner Ring for Suggested
Bore C4
CO of RIC RIC Reduction RIC After
(Nominal) Tapered Shaft(1)(2)
Min. Max. Min. Max. Due to Installation(1)
Installation
C2 C3 C5 Taper 1:12 Taper 1:30
Over Incl. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min.
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in. in. in. in. in.
20 30 0.02 0.03 0.04 0.055 0.075 0.095 0.015 0.02 0.23 0.30 0.015

0.9449 1.1811 0.0008 0.0012 0.0016 0.0022 0.003 0.0037 0.0006 0.0008 0.0091 0.0118 0.0006
30 40 0.025 0.035 0.05 0.065 0.085 0.105 0.02 0.025 0.30 0.38 0.015

1.1811 1.5748 0.001 0.0014 0.002 0.0026 0.0033 0.0041 0.0008 0.001 0.0118 0.0150 0.0006
40 50 0.03 0.045 0.06 0.08 0.1 0.13 0.025 0.03 0.38 0.46 0.02

1.5748 1.9685 0.0012 0.0018 0.0024 0.0031 0.0039 0.0051 0.001 0.0012 0.0150 0.0181 0.0008
50 65 0.04 0.055 0.075 0.095 0.12 0.16 0.03 0.038 0.46 0.56 0.025

1.9685 2.5591 0.0016 0.0022 0.003 0.0037 0.0047 0.0063 0.0012 0.0015 0.0181 0.0220 0.001
65 80 0.05 0.07 0.095 0.12 0.15 0.2 0.038 0.051 0.56 0.76 0.025

2.5591 3.1496 0.002 0.0028 0.0037 0.0047 0.0059 0.0079 0.0015 0.002 0.0220 0.0299 0.001
80 100 0.055 0.08 0.11 0.14 0.18 0.23 0.046 0.064 0.68 0.97 0.036

3.1496 3.9370 0.0022 0.003 0.0043 0.0055 0.0071 0.0091 0.0018 0.0025 0.0268 0.0382 0.0014
100 120 0.065 0.1 0.135 0.17 0.22 0.28 0.051 0.071 0.76 1.07 1.90 2.54 0.051
3.9370 4.7244 0.0026 0.0039 0.0053 0.0067 0.0087 0.011 0.002 0.0028 0.0299 0.0421 0.0748 0.1000 0.002
120 140 0.08 0.12 0.16 0.2 0.26 0.33 0.064 0.089 0.89 1.27 2.29 3.05 0.056
4.7244 5.5118 0.0031 0.0047 0.0063 0.0079 0.0102 0.013 0.0025 0.0035 0.0350 0.0500 0.0902 0.1201 0.0022
140 160 0.09 0.13 0.18 0.23 0.3 0.38 0.076 0.102 1.14 1.52 2.67 3.43 0.056
5.5118 6.2992 0.0035 0.0051 0.0071 0.0091 0.0118 0.015 0.003 0.004 0.0449 0.0598 0.1051 0.1350 0.0022
160 180 0.1 0.14 0.2 0.26 0.34 0.43 0.076 0.114 1.14 1.65 2.67 4.06 0.061
6.2992 7.0866 0.0039 0.0055 0.0079 0.0102 0.0134 0.0169 0.003 0.0045 0.0449 0.0650 0.1051 0.1598 0.0024
180 200 0.11 0.16 0.22 0.29 0.37 0.47 0.089 0.127 1.40 1.90 3.05 4.45 0.071
7.0866 7.8740 0.0043 0.0063 0.0087 0.0114 0.0146 0.0185 0.0035 0.005 0.0551 0.0748 0.1201 0.1752 0.0028
200 225 0.12 0.18 0.25 0.32 0.41 0.52 0.102 0.14 1.52 2.03 3.56 4.83 0.076
7.8740 8.8582 0.0047 0.0071 0.0098 0.0126 0.0161 0.0205 0.004 0.0055 0.0598 0.0799 0.1402 0.1902 0.003
225 250 0.14 0.2 0.27 0.35 0.45 0.57 0.114 0.152 1.78 2.29 4.06 5.33 0.089
8.8582 9.8425 0.0055 0.0079 0.0106 0.0138 0.0177 0.0224 0.0045 0.006 0.0701 0.0902 0.1598 0.2098 0.0035
250 280 0.15 0.22 0.3 0.39 0.49 0.62 0.114 0.165 1.78 2.54 4.06 5.84 0.102
9.8425 11.0236 0.0059 0.0087 0.0118 0.0154 0.0193 0.0244 0.0045 0.0065 0.0701 0.1000 0.1598 0.2299 0.004
280 315 0.17 0.24 0.33 0.43 0.54 0.68 0.127 0.178 1.90 2.67 4.45 6.22 0.102
11.0236 12.4016 0.0067 0.0094 0.013 0.0169 0.0213 0.0268 0.005 0.007 0.0748 0.1051 0.1752 0.2449 0.004
315 355 0.19 0.27 0.36 0.47 0.59 0.74 0.14 0.19 2.03 2.79 4.83 6.60 0.114
12.4016 13.9764 0.0075 0.0106 0.0142 0.0185 0.0232 0.0291 0.0055 0.0075 0.0799 0.1098 0.1902 0.2598 0.0045
355 400 0.21 0.3 0.4 0.52 0.65 0.82 0.152 0.203 2.29 3.05 5.33 7.11 0.127
13.9764 15.7480 0.0083 0.0118 0.0157 0.0205 0.0256 0.0323 0.006 0.008 0.0902 0.1201 0.2098 0.2799 0.005
400 450 0.23 0.33 0.44 0.57 0.72 0.91 0.165 0.216 2.54 3.3 5.84 7.62 0.152
15.7480 17.7165 0.0091 0.013 0.0173 0.0224 0.0283 0.0358 0.0065 0.0085 0.1000 0.1299 0.2299 0.3000 0.006
450 500 0.26 0.37 0.49 0.63 0.79 1 0.178 0.229 2.67 3.43 6.22 8.00 0.165
17.7165 19.6850 0.0102 0.0146 0.0193 0.0248 0.0311 0.0394 0.007 0.009 0.1051 0.1350 0.2449 0.3150 0.0065
500 560 0.29 0.41 0.54 0.68 0.87 1.1 0.203 0.254 3.05 3.81 7.11 8.89 0.178
19.6850 22.0472 0.0114 0.0161 0.0213 0.0268 0.0343 0.0433 0.008 0.01 0.1201 0.1500 0.2799 0.3500 0.007
560 630 0.32 0.46 0.6 0.76 0.98 1.23 0.229 0.279 3.43 4.19 8.00 9.78 0.203
22.0472 24.8031 0.0126 0.0181 0.0236 0.0299 0.0386 0.0484 0.009 0.011 0.1350 0.1650 0.3150 0.3850 0.008
630 710 0.35 0.51 0.67 0.85 1.09 1.36 0.254 0.305 3.81 4.57 8.89 10.67 0.203
24.8031 27.9528 0.0138 0.0201 0.0264 0.0335 0.0429 0.0535 0.01 0.012 0.1500 0.1799 0.3500 0.4201 0.008
710 800 0.39 0.57 0.75 0.96 1.22 1.5 0.279 0.356 4.19 5.33 9.78 12.45 0.229
27.9528 31.4961 0.0154 0.0224 0.0295 0.0378 0.048 0.0591 0.011 0.014 0.1650 0.2098 0.3850 0.4902 0.009
800 900 0.44 0.64 0.84 1.07 1.37 1.69 0.305 0.381 4.57 5.72 10.67 13.33 0.252
31.4961 35.4331 0.0173 0.0252 0.0331 0.0421 0.0539 0.0665 0.012 0.015 0.1799 0.2252 0.4201 0.5248 0.01
900 1000 0.49 0.71 0.93 1.19 1.52 1.86 0.356 0.432 5.33 6.48 12.45 15.11 0.279
35.4331 39.3701 0.0193 0.028 0.0366 0.0469 0.0598 0.0732 0.014 0.017 0.2100 0.2551 0.4902 0.5949 0.011
(1)
This displacement is valid for assembly of tapered bore bearings and is measured starting from a line-to-line t of the bearing bore to the tapered shaft.
(2)
1:12 Taper used for 222, 223, 230, 231, 232, 233, 239 series. 1:30 Taper used for 240, 241, 242 series. For sleeve mounting, multiply axial displacement values by 1.1 for 1:12 Taper or
by 1.05 for 1:30 Taper. For questions on tapered shaft data, consult your Timken engineer.
NOTE: Axial displacement values apply to solid steel shafts or hollow shafts with bore diameter less than half the shaft diameter. For shaft materials other than steel, or for
thin-walled shafts, please consult your Timken engineer.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

24 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING MOUNTING, FITTING, SETTING AND INSTALLATION

EXAMPLE #1
Calculating RIC Reduction Using a Spherical Roller Bearing with Tapered Bore
Given bearing number 22328K C3 (140 mm bore with C3 clearance)
is to be mounted on a tapered shaft. Using a set of feeler gages,
RIC is measured at (see g. 3):
RIC = 0.178 mm
Suggested reduction of RIC due to installation =
0.064 mm 0.089 mm, found in table 5 on page 24.
Calculate the clearance after mounting (see g. 4):
Fig. 3. Measure RIC before Fig. 4. During mounting, the
0.178 mm 0.076 mm = 0.102 mm installation. RIC should be checked at the
unloaded roller.
For this example, the value of 0.076 mm was obtained by taking the mid-range value of
the upper and lower limits found in the tables on page 24.

Therefore, the locknut should be tightened until RIC reaches This differs from the value calculated in the example. The value
0.102 mm. taken directly from the table is provided as a minimum value.
It also should be noted that the value obtained by reading the It is not suggested to use a calculated value that falls below
suggested RIC after installation directly from the table is 0.056 mm. this minimum.

EXAMPLE #2
Calculating RIC Reduction Using a Spherical Roller Bearing with Cylindrical Bore
Observations:
Bearing 22230EM, nominal 150 mm bore and 270 mm O.D., t is loose. We also know that the bearing speed is 1200 RPM or
standard class, operating at 1200 RPM. 60 percent of the speed rating.
Float bearing position so the stationary O.D. should be free
As a general rule of thumb, we increase the clearance for
to move in SNT housing, with the locating ring removed.
operating speeds that exceed 70 percent of the speed rating, due
With shaft/inner ring rotation and the moderate loading
to concerns over internal heat generation and thermal growth.
0.09C, the bore should be tight t.
In this case, we are at 60 percent of the speed rating, so normal
We can use the nominal t charts in table 6 on page 29 (shaft t) clearance, ISO CO or the SNT standard C3, can be selected.
to help guide our ISO t selection.
Observing the RIC chart on page 23, we nd for 150 mm nominal
bore at CO, the RIC will be 0.110 mm to 0.170 mm. We also note
Shaft Fit at 150 mm Bore: ISO p6
that the minimum recommended RIC (installed) is 0.056 mm.
From the shaft t chart at 150 mm nominal bore at p6 (table 8,
Also from page 23, we note that we get an approximate reduction of
page 34), the shaft tolerance is nominal +0.043 to +0.068 mm.
RIC that is 80 percent of interference t on a solid housing. Since we
Therefore we have the following bore range:
have a loose housing t, there will be no RIC reduction from that t.
max. shaft = 150.068 mm
min. shaft = 150.043 mm Shaft t RIC reductions and clearance:
This yields a shaft t: For a 150 mm nominal bore at C3, the RIC will be 0.115 mm to
0.165 mm. Recalculating shaft t RIC reduction and clearance:
max. t = max. shaft - min. bore
max. clearance = max. RIC - min. t reduction
= 150.068 - 149.075
= 0.165 - 0.034 = 0.131 mm
= 0.093 mm tight
min. clearance = min. RIC - max. t reduction
min. t = min. shaft - max. bore
= 0.115 - 0.074 = 0.041 mm
= 150.043 - 150.000
= 0.043 mm tight Since the minimum mounted clearance is less than the minimum
suggested RIC of 0.056 mm, the C3 RIC clearance limit needs to
For the primary selection of RIC, the major parameters are the
be reevaluated.
bearing speed and the ts. For our example, we know that the
shaft t is 0.043 mm tight to 0.093 mm tight. We know the housing

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 25
SNT SPLIT PLUMMER BLOCKS
ENGINEERING MOUNTING, FITTING, SETTING AND INSTALLATION

INSTALLATION
When using a tight t inner ring, the method of assembly will SHAFT AND HOUSING FINISH
depend on whether the bearing has a cylindrical or tapered bore.
Shaft surfaces on which the bearing will be mounted must
be clean and free from nicks and burrs.
CLEANLINESS
For applications with stationary housing and rotating shaft,
Choose a clean environment, free from dust and moisture. it is suggested that the bearing seat on the shaft be ground
The installer should make every effort to ensure cleanliness to 1.6 m (65 in.) Ra maximum.
by use of protective screens and clean cloths. If it is impractical to use a ground nish, a machined nish
of 3.2 m (125 in.) Ra is acceptable in many cases, but the
PLAN THE WORK amount of interference t should be slightly increased.
Know your plans in advance and have the necessary
INSTALLING CYLINDRICAL BORE BEARINGS
tools at hand. This reduces the amount of time for the job
and decreases the chance for contamination to get into
the bearing. Heat expansion method
Most applications require a tight interference t on the
INSPECTION AND PREPARATION shaft.
All component parts of the machine should be on hand and Mounting is simplied by heating the bearing to expand it
thoroughly cleaned before proceeding. sufciently to slide easily onto the shaft.
Housings should be cleaned, including blowing out the oil Two methods of heating are commonly used:
holes. 1. Tank of heated oil.
Do not use an air hose on bearings. Accomplished by heating the bearing in a tank of oil
If blind holes are used, insert a magnetic rod to remove that has a high ash point (see g. 5).
metal chips that might be lodged there during fabrication. The oil temperature should not be allowed to exceed
Shaft shoulders and spacer rings contacting the bearing 121 C (250 F). A temperature of 93 C (200 F) is
should be square with the shaft axis. sufcient for most applications.
The shaft llet must be small enough to clear the radius of The bearing should be heated for 20 or 30 minutes,
the bearing. or until it is expanded sufciently to slide onto the
On original installations, all component parts should shaft easily.
be checked against the detail specication prints for The oil bath is shown in g. 5. The bearing should not
dimensional accuracy. Shaft and housing should be be in direct contact with the heat source.
carefully checked for size and form (roundness, etc.). The usual arrangement is to have a screen several
inches from the bottom of the tank. Small support
blocks separate the bearing from the screen.
WARNING It is important to keep the bearing away from
any localized high-heat source that may raise its
Failure to observe the following warnings
temperature excessively, resulting in metallurgical
could create a risk of death or serious injury.
property changes such as in ring hardness reduction.

Proper maintenance and handling practices are critical.


Flame-type burners are commonly used. An automatic
device for temperature control is desirable.
Always follow installation instructions and maintain
proper lubrication. If safety regulations prevent the use of an open heated
oil bath, a mixture of 15 percent soluble-oil water may
Never spin a bearing with compressed air. The components be used. This mixture may be heated to a maximum of
may be forcefully expelled. 93 C (200 F) without being ammable.

CAUTION
Failure to follow these cautions
could create a risk of injury.

Remove oil or rust inhibitor from parts before heating,


to avoid re and fumes.

26 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING MOUNTING, FITTING, SETTING AND INSTALLATION

2. Induction heating. Arbor press method


The induction heating process can be used for An alternate method of mounting, generally used only on
mounting bearings. smaller size bearings, is to press the bearing onto the shaft
Induction heating is rapid. Care must be taken to or into the housing. This can be done by using an arbor
prevent bearing temperature from exceeding press and a mounting tube as shown in g. 6.
93 C (200 F). The tube should be made from soft steel with an inside
Trial runs with the unit and bearing are usually diameter slightly larger than the shaft.
necessary to obtain proper timing. The O.D. of the tube should not exceed the shaft backing
Thermal crayons melted at predetermined temperatures or diameter given in the Timken Spherical Roller Bearing
Catalog (order no. 10446), found on www.timken.com.
thermal gun can be used to check the bearing temperature.
While the bearing is hot, it should be positioned squarely The tube should be faced square at both ends. It should be
against the shoulder. thoroughly clean inside and out, and long enough to clear
the end of the shaft after the bearing is mounted.
Lockwashers and locknuts or clamping plates are then
installed to hold the bearing against the shoulder of If the outer ring is being pressed into the housing, the
the shaft. O.D. of the mounting tube should be slightly smaller
than the housing bore. The I.D. should not be less than
As the bearing cools, the locknut or clamping plate should
the suggested housing backing diameter in the table of
be tightened.
dimensions available in the Timken Spherical Roller Bearing
For more information see the Timken Spherical Roller Catalog (order no. 10446), found on www.timken.com.
Bearing Catalog (order no. 10446), found on
www.timken.com. Coat the shaft with a light machine oil to reduce the force
needed for a press t.
Carefully place the bearing on the shaft, making sure it is
NOTE square with the shaft axis.
Never use steam or hot water when cleaning the bearings Apply steady pressure from the arbor ram to drive the
because these methods can create rust or corrosion. bearing rmly against the shoulder.
Never expose any surface of a bearing to the ame of a torch.
Do not heat bearing beyond 149 C (300 F). NOTE
Never attempt a press t on a shaft by applying pressure
to the outer ring or a press t in a housing by applying pressure
to the inner ring.

Oil
Bearing

Bearing support
block

Bearing held Flame burner


from bottom
by screen

Fig. 5. Heat expansion method. Fig. 6. Arbor press method.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 27
SNT SPLIT PLUMMER BLOCKS
ENGINEERING MOUNTING, FITTING, SETTING AND INSTALLATION

Mounting tapered bore spherical roller bearings


Use a feeler gage with the thinnest blade of 0.038 mm.
Place the bearing in an upright position with the inner and
outer ring faces parallel.
Place thumbs on the inner ring bore and oscillate the inner
ring the distance of two or three roller spacings.
Position the individual roller assemblies so that a roller is at
the top of the inner ring on both sides of the bearing.
With the roller in the correct position, insert a thin blade of
the feeler gage between the roller and the outer ring, as
shown in g. 7.
Move the feeler gage carefully along the top roller between
the roller and outer ring raceway. Repeat this procedure
using thicker feeler gage blades until one is found that will
not go through.
The blade thickness that preceded the no-go blade is a
measure of RIC before installation.
Start the mounting procedure by lubricating the tapered
shaft with a light coat of machine oil.
Slide the bearing onto the shaft as far as it will go by hand.
As the locknut is tightened, the interference t builds up,
resulting in expansion of the inner ring.
Periodically measure to monitor the reduction in RIC.
Continue the procedure until the proper amount of reduction
is obtained. Do not exceed calculated amount of reduction.
As a nal check, make sure the remaining RIC equals or
exceeds the minimum mounted clearance shown in table 5
on page 24.
During mounting, the RIC should be checked at the
unloaded roller. If this is at the bottom, make sure that the
roller is raised to seat rmly at the inboard position of the
inner ring.
When the suggested amount of RIC reduction has been
accomplished, the bearing is properly tted.
Complete the procedure by peening the lockwasher tang
into the locknut slot or securing the lockplate.

Fig. 7. Measure RIC before installation.

28 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING SHAFT FITS FOR CYLINDRICAL BORE BEARINGS

SHAFT FITS FOR CYLINDRICAL BORE BEARINGS


This chart is a guideline for specifying shaft fits related to
particular operating conditions. Please contact your Timken
engineer for more information.

TABLE 6. RADIAL SPHERICAL ROLLER BEARING SHAFT FITS


Conditions Examples Shaft Dia. Tolerance Symbol(1) Remarks
mm
in.
Stationary The inner ring not to be Wheel on non-rotating shaft g6
All diameters
inner ring load easily displaced on the shaft Tension pulleys and rope sheaves h6
over incl.
18 100 k6 In very accurate
Light and variable loads Electrical apparatus, machine tools, 0.7087 3.9370 applications, k5 and m5
P 0.07C pumps, ventilators, industrial trucks are used instead of k6
100 200 and m6 respectively.
3.9370 7.8740 m6

18 65
0.7087 2.5590 m5

65 100
2.5590 3.9370 m6
Applications in general, 100 140
Normal and heavy loads electrical motors, turbines, pumps, 3.9370 5.5118 n6
P > 0.07C combustion engines,
0.25C gear transmissions, 140 280
Rotating 5.5118 11.0236 p6
woodworking machines
inner ring load 280 500
or indeterminate 11.0236 19.6850 r6
load direction
500
and up r7
19.6850
18 65
m6
0.7087 2.5590
65 100
n6
2.5590 3.9370
Very heavy loads and Journal boxes for locomotives and Bearings with greater
shock loads other heavy rail vehicles, 100 140 clearance than normal
p6
3.9370 5.5118
P > 0.25C traction motors must be used.
140 200
r6
5.5118 7.8740
200 500
r7
7.8740 19.6850
BEARINGS WITH TAPERED BORE AND ADAPTER SLEEVE
See tables for Reduction
All loads Applications in general All diameters of RIC on pages
23 and 24.

(1)
For solid steel shaft. See tables on pages 30 through 35 for tolerance value.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 29
SNT SPLIT PLUMMER BLOCKS
ENGINEERING FITTING PRACTICE TABLES
These charts are guidelines for specifying shaft and housing ts related to particular operating conditions in table 6 on page 29.

FITTING PRACTICE TABLES


TABLE 7. SPHERICAL ROLLER BEARINGS - SHAFT TOLERANCES (CLASSES g6, h5, h6, j5, j6, k5, k6, m5)
Bearing Bore g6 h6 h5 j5
Nominal (Max.) Shaft Dia. Shaft Dia. Shaft Dia. Shaft Dia.
Tolerance(1) Fit Fit Fit Fit
Over Incl. Max. Min. Max. Min. Max. Min. Max. Min.
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in. in. in. in. in.
0.025L 0.016L 0.005L
30.000 50.000 -0.014 -0.009 -0.025 0.003T 0.000 -0.016 0.012T +0.006 -0.005 0.018T

1.1811 1.9685 -0.0006 -0.0004 -0.0010 0.0010L 0.0000 -0.0006 0.0006L +0.0002 -0.0002 0.0002L
0.0001T 0.0005T 0.0007T
0.029L 0.019L 0.007L
50.000 80.000 -0.015 -0.010 -0.029 0.005T 0.000 -0.019 0.015T +0.006 -0.007 0.021T

1.9685 3.1496 -0.0006 -0.0004 -0.0011 0.0011L 0.0000 -0.0007 0.0007L +0.0002 -0.0003 0.0003L
0.0002T 0.0006T 0.0008T
0.034L 0.022L 0.009L
80.000 120.000 -0.020 -0.012 -0.034 0.008T 0.000 -0.022 0.020T +0.006 -0.009 0.026T

3.1496 4.7244 -0.0008 -0.0005 -0.0013 0.0013L 0.0000 -0.0009 0.0009L +0.0002 -0.0004 0.0004L
0.0003T 0.0008T 0.0010T
0.039L 0.025L 0.011L
120.000 180.000 -0.025 -0.014 -0.039 0.011T 0.000 -0.025 0.025T +0.007 -0.011 0.032T

4.7244 7.0866 -0.0010 -0.0006 -0.0015 0.0015L 0.0000 -0.0010 0.0010L +0.0003 -0.0004 0.0004L
0.0004T 0.0010T 0.0013T
0.044T 0.029L 0.013L
180.000 200.000 -0.030 -0.015 -0.044 0.015T 0.000 -0.029 0.030T +0.007 -0.013 0.037T

7.0866 7.8740 -0.0012 -0.0006 -0.0017 0.0017L 0.0000 -0.0011 0.0011L +0.0003 -0.0005 0.0005L
0.0006T 0.0012T 0.0015T
0.044T 0.029L 0.013L
200.000 225.000 -0.030 -0.015 -0.044 0.015T 0.000 -0.029 0.030T +0.007 -0.013 0.037T

7.8740 8.8583 -0.0012 -0.0006 -0.0017 0.0017L 0.0000 -0.0011 0.0011L +0.0003 -0.0005 0.0005L
0.0006T 0.0012T 0.0015T
0.044T 0.029L 0.013L
225.000 250.000 -0.030 -0.015 -0.044 0.015T 0.000 -0.029 0.030T +0.007 -0.013 0.037T

8.8583 9.8425 -0.0012 -0.0006 -0.0017 0.0017L 0.0000 -0.0011 0.0011L +0.0003 -0.0005 0.0005L
0.0006T 0.0012T 0.0015T
0.049L 0.032L 0.016L
250.000 280.000 -0.035 -0.017 -0.049 0.018T 0.000 -0.032 0.035T +0.007 -0.016 0.042T

9.8425 11.0236 -0.0014 -0.0007 -0.0019 0.0019L 0.0000 -0.0013 0.0013L +0.0003 -0.0006 0.0006L
0.0007T 0.0014T 0.0017T
0.049L 0.032L 0.016L
280.000 315.000 -0.035 -0.017 -0.049 0.018T 0.000 -0.032 0.035T +0.007 -0.016 0.042T

11.0236 12.4016 -0.0014 -0.0007 -0.0019 0.0019L 0.0000 -0.0013 0.0013L +0.0003 -0.0006 0.0006L
0.0007T 0.0014T 0.0017T
0.054L 0.036L 0.018L
315.000 355.000 -0.040 -0.018 -0.054 0.022T 0.000 -0.036 0.040T +0.007 -0.018 0.047T

12.4016 13.9764 -0.0016 -0.0007 -0.0021 0.0021L 0.0000 -0.0014 0.0014L +0.0003 -0.0007 0.0007L
0.0009T 0.0016T 0.0019T
(1)
Tolerance range is from +0 to value listed.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

30 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING FITTING PRACTICE TABLES
These charts are guidelines for specifying shaft and housing ts related to particular operating conditions in table 6 on page 29.

j6 k5 k6 m5
Shaft Dia. Shaft Dia. Shaft Dia. Shaft Dia.
Fit Fit Fit Fit
Max. Min. Max. Min. Max. Min. Max. Min.
mm mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in. in.
0.005L 0.002T 0.002T 0.009T
+0.011 -0.005 0.023T +0.013 +0.002 0.025T +0.018 +0.002 0.030T +0.020 +0.009 0.032T
+0.0004 -0.0002 0.0002L +0.0005 +0.0001 0.0001T +0.0007 +0.0001 0.0001T +0.0008 +0.0004 0.0004T
0.00085T 0.0010T 0.0012T 0.00125T
0.007L 0.002T 0.002T 0.011T
+0.012 -0.007 0.027T +0.015 +0.002 0.030T +0.021 +0.002 0.036T +0.024 +0.011 0.039T
+0.0005 -0.0003 0.0003L +0.0006 +0.0001 0.0001T +0.0008 +0.0001 0.0001T +0.0009 +0.0004 0.0004T
0.0011T 0.0012T 0.0014T 0.0015T
0.009L 0.003T 0.003T 0.013T
+0.013 -0.009 0.033T +0.018 +0.003 0.038T +0.025 +0.003 0.045T +0.028 +0.013 0.048T
+0.0005 -0.0004 0.0004L +0.0007 +0.0001 0.0001T +0.0010 +0.0001 0.0001T +0.0011 +0.0005 0.0005T
0.0013T 0.0015T 0.0018T 0.0019T
0.011L 0.003T 0.003T 0.015T
+0.014 -0.011 0.039T +0.021 +0.003 0.046T +0.028 +0.003 0.053T +0.033 +0.015 0.058T
+0.0006 -0.0004 0.0004L +0.0008 +0.0001 0.0001T +0.0011 +0.0001 0.0001T +0.0013 +0.0006 0.0006T
0.0016T 0.0018T 0.0021T 0.0023T
0.013L 0.004T 0.017T
+0.016 -0.013 0.046T +0.024 +0.004 0.054T +0.037 +0.017 0.067T

+0.0006 -0.0005 0.0005L +0.0009 +0.0002 0.0002T +0.0015 +0.0007 0.0007T
0.0018T 0.0021T 0.0027T
0.013L 0.004T 0.017T
+0.016 -0.013 0.046T +0.024 +0.004 0.054T +0.037 +0.017 0.067T

+0.0006 -0.0005 0.0005L +0.0009 +0.0002 0.0002T +0.0015 +0.0007 0.0007T
0.0018T 0.0021T 0.0027T
0.013L 0.004T 0.017T
+0.016 -0.013 0.046T +0.024 +0.004 0.054T +0.037 +0.017 0.067T

+0.0006 -0.0005 0.0005L +0.0009 +0.0002 0.0002T +0.0015 +0.0007 0.0007T
0.0018T 0.0021T 0.0027T
0.016L 0.004T 0.020T
+0.016 -0.016 0.051T +0.027 +0.004 0.062T +0.043 +0.020 0.078T

+0.0006 -0.0006 0.0006L +0.0011 +0.0002 0.0002T +0.0017 +0.0008 0.0008T
0.0020T 0.0025T 0.0031T
0.016L 0.004T 0.020T
+0.016 -0.016 0.051T +0.027 +0.004 0.062T +0.043 +0.020 0.078T

+0.0006 -0.0006 0.0006L +0.0011 +0.0002 0.0002T +0.0017 +0.0008 0.0008T
0.0020T 0.0025T 0.0031T
0.018L 0.004T 0.021T
+0.018 -0.018 0.058T +0.029 +0.046 0.069T +0.046 +0.021 0.086T

+0.0007 -0.0007 0.0007L +0.0011 +0.0002 0.0002T +0.0018 +0.0008 0.0008T
0.0023T 0.0027T 0.0034T
(1)
Tolerance range is from +0 to value listed.
Continued on next page.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 31
SNT SPLIT PLUMMER BLOCKS
ENGINEERING FITTING PRACTICE TABLES
These charts are guidelines for specifying shaft and housing ts related to particular operating conditions in table 6 on page 29.

TABLE 7. SPHERICAL ROLLER BEARINGS - SHAFT TOLERANCES (CLASSES g6, h5, h6, j5, j6, k5, k6, m5) continued
Bearing Bore g6 h6 h5 j5
Nominal (Max.) Shaft Dia. Shaft Dia. Shaft Dia. Shaft Dia.
Tolerance(1) Fit Fit Fit Fit
Over Incl. Max. Min. Max. Min. Max. Min. Max. Min.
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in. in. in. in. in.
0.054L 0.036L 0.018L
355.000 400.000 -0.040 -0.018 -0.054 0.022T 0.000 -0.036 0.040T +0.007 -0.018 0.047T

13.9764 15.7480 -0.0016 -0.0007 -0.0021 0.0021L 0.0000 -0.0014 0.0014L +0.0003 -0.0007 0.0007L
0.0009T 0.0016T 0.0019T
0.060L 0.040L 0.020L
400.000 450.000 -0.045 -0.020 -0.060 0.025T 0.000 -0.040 0.045T +0.007 -0.020 0.052T

15.7480 17.7165 -0.0018 -0.0008 -0.0024 0.0024L 0.0000 -0.0016 0.0016L +0.0003 -0.0008 0.0008L
0.0010T 0.0018T 0.0021T
0.060L 0.040L 0.020L
450.000 500.000 -0.045 -0.020 -0.060 0.025T 0.000 -0.040 0.045T +0.007 -0.020 0.052T

17.7165 19.6850 -0.0018 -0.0008 -0.0024 0.0024L 0.0000 -0.0016 0.0016L +0.0003 -0.0008 0.0008L
0.0010T 0.0018T 0.0020T
(1)
Tolerance range is from +0 to value listed.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

32 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING FITTING PRACTICE TABLES
These charts are guidelines for specifying shaft and housing ts related to particular operating conditions in table 6 on page 29.

j6 k5 k6 m5
Shaft Dia. Shaft Dia. Shaft Dia. Shaft Dia.
Fit Fit Fit Fit
Max. Min. Max. Min. Max. Min. Max. Min.
mm mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in. in.
0.018L 0.004T 0.021T
+0.018 -0.018 0.058T +0.029 +0.004 0.069T +0.046 +0.021 0.086T

+0.0007 -0.0007 0.0007L +0.0011 +0.0002 0.0002T +0.0018 +0.0008 0.0008T
0.0023T 0.0027T 0.0034T
0.020L 0.005T 0.023T
+0.020 -0.020 0.065T +0.032 +0.005 0.077T +0.050 +0.023 0.095T

+0.0008 -0.0008 0.0008L +0.0013 +0.0002 0.0002T +0.0020 +0.0009 0.0009T
0.0026T 0.0031T 0.0037T
0.020L 0.005T 0.023T
+0.020 -0.020 0.065T +0.032 +0.005 0.077T +0.050 +0.023 0.095T

+0.0008 -0.0008 0.0008L +0.0013 +0.0002 0.0002T +0.0020 +0.0009 0.0009T
0.0026T 0.0031T 0.0037T
(1)
Tolerance range is from +0 to value listed.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 33
SNT SPLIT PLUMMER BLOCKS
ENGINEERING FITTING PRACTICE TABLES
These charts are guidelines for specifying shaft and housing ts related to particular operating conditions in table 6 on page 29.

TABLE 8. SPHERICAL ROLLER BEARINGS - SHAFT TOLERANCES (CLASSES m6, n6, p6, r6, r7)
Bearing Bore m6 n6 p6 r6 r7
Nominal (Max.) Shaft Dia. Shaft Dia. Shaft Dia. Shaft Dia. Shaft Dia.
Tolerance(1) Fit Fit Fit Fit Fit
Over Incl. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min.
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in.
0.009T
30.000 50.000 -0.014 +0.025 +0.009 0.037T

1.1811 1.9685 -0.0006 +0.0010 +0.0004 0.0004T
0.0145T
0.011T 0.020T
50.000 80.000 -0.015 +0.030 +0.011 0.045T +0.039 +0.020 0.054T

1.9685 3.1496 -0.0006 +0.0012 +0.0004 0.0004T +0.0015 +0.0008 0.0008T
0.0018T 0.0021T
0.013T 0.023T 0.037T
80.000 120.000 -0.020 +0.035 +0.013 0.055T +0.045 +0.023 0.065T +0.059 +0.037 0.079T

3.1496 4.7244 -0.0008 +0.0014 +0.0005 0.0005T +0.0018 +0.0009 0.0009T +0.0023 +0.0015 0.0015T
0.0022T 0.0026T 0.0031T
0.015T 0.027T 0.043T 0.065T
120.000 180.000 -0.025 +0.040 +0.015 0.065T +0.052 +0.027 0.077T +0.068 +0.043 0.093T +0.090 +0.065 0.115T

4.7244 7.0866 -0.0010 +0.0016 +0.0006 0.0006T +0.0020 +0.0011 0.0011T +0.0027 +0.0017 0.0017T +0.0035 +0.0026 0.0026T
0.0026T 0.0030T 0.0037T 0.0045T
0.017T 0.031L 0.050T 0.077T
180.000 200.000 -0.030 +0.046 +0.017 0.076T +0.060 +0.031 0.090T +0.079 +0.050 0.109T +0.106 +0.077 0.136T

7.0866 7.8740 -0.0012 +0.0018 +0.0007 0.0007T +0.0024 +0.0012 0.0012L +0.0031 +0.0020 0.0020T +0.0042 +0.0030 0.0030T
0.0030T 0.0036T 0.0043T 0.0054T
0.017T 0.031L 0.050T 0.080T 0.080T
200.000 225.000 -0.030 +0.046 +0.017 0.076T +0.060 +0.031 0.090T +0.079 +0.050 0.109T +0.109 +0.080 0.139T +0.126 +0.080 0.156T
7.8740 8.8583 -0.0012 +0.0018 +0.0007 0.0007T +0.0024 +0.0012 0.0012L +0.0031 +0.0020 0.0020T +0.0043 +0.0031 0.0031T +0.0050 +0.0031 0.0031T
0.0030T 0.0036T 0.0043T 0.0055T 0.0062T
0.017T 0.031L 0.050T 0.084T 0.084T
225.000 250.000 -0.030 +0.046 +0.017 0.076T +0.060 +0.031 0.090T +0.079 +0.050 0.109T +0.113 +0.084 0.143T +0.130 +0.084 0.160T
8.8583 9.8425 -0.0012 +0.0018 +0.0007 0.0007T +0.0024 +0.0012 0.0012L +0.0031 +0.0020 0.0020T +0.0044 +0.0033 0.0033T +0.0051 +0.0033 0.0033T
0.0030T 0.0036T 0.0043T 0.0056T 0.0063T
0.020T 0.034T 0.056T 0.094T 0.094T
250.000 280.000 -0.035 +0.052 +0.020 0.087T +0.066 +0.034 0.101T +0.088 +0.056 0.123T +0.126 +0.094 0.161T +0.146 +0.094 0.181T
9.8425 11.0236 -0.0014 +0.0020 +0.0008 0.0008T +0.0026 +0.0013 0.0013T +0.0035 +0.0022 0.0022T +0.0050 +0.0037 0.0037T +0.0057 +0.0037 0.0037T
0.0034T 0.0040T 0.0049T 0.0064T 0.0071T
0.020T 0.034T 0.056T 0.098T 0.098T
280.000 315.000 -0.035 +0.052 +0.020 0.087T +0.066 +0.034 0.101T +0.088 +0.056 0.123T +0.130 +0.098 0.165T +0.150 +0.098 0.185T
11.0236 12.4016 -0.0014 +0.0020 +0.0008 0.0008T +0.0026 +0.0013 0.0013T +0.0035 +0.0022 0.0022T +0.0051 +0.0039 0.0039T +0.0059 +0.0039 0.0039T
0.0034T 0.0040T 0.0049T 0.0065T 0.0073T
0.021T 0.037T 0.062T 0.108T 0.108T
315.000 355.000 -0.040 +0.057 +0.021 0.097T +0.073 +0.037 0.113T +0.098 +0.062 0.138T +0.144 +0.108 0.184T +0.165 +0.108 0.205T
12.4016 13.9764 -0.0016 +0.0022 +0.0008 0.0008T +0.0029 +0.0015 0.0015T +0.0039 +0.0024 0.0024T +0.0057 +0.0043 0.0043T +0.0065 +0.0043 0.0043T
0.0038T 0.0045T 0.0055T 0.0073T 0.0081T
(1)
Tolerance range is from +0 to value listed.
Continued on next page.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

34 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING FITTING PRACTICE TABLES
These charts are guidelines for specifying shaft and housing ts related to particular operating conditions in table 6 on page 29.

Continued from previous page.

Bearing Bore m6 n6 p6 r6 r7
Nominal (Max.) Shaft Dia. Shaft Dia. Shaft Dia. Shaft Dia. Shaft Dia.
Tolerance(1) Fit Fit Fit Fit Fit
Over Incl. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min.
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in. in.
0.037T 0.062T 0.114T 0.114T
355.000 400.000 -0.040 +0.073 +0.037 0.113T +0.098 +0.062 0.138T +0.150 +0.114 0.190T +0.171 +0.114 0.211T

13.9764 15.7480 -0.0016 +0.0029 +0.0015 0.0015T +0.0039 +0.0024 0.0024T +0.0059 +0.0045 0.0045T +0.0067 +0.0045 0.0045T
0.0045T 0.0055T 0.0075T 0.0083T
0.040T 0.068T 0.126T 0.126T
400.000 450.000 -0.045 +0.080 +0.040 0.125T +0.108 +0.068 0.153T +0.166 +0.126 0.211T +0.189 +0.126 0.234T

15.7480 17.7165 -0.0018 +0.0031 +0.0016 0.0016T +0.0043 +0.0027 0.0027T +0.0065 +0.0050 0.0050T +0.0074 +0.0050 0.0050T
0.0049T 0.0061T 0.0083T 0.0092T
0.040T 0.068T 0.132T 0.132T
450.000 500.000 -0.045 +0.080 +0.040 0.125T +0.108 +0.068 0.153T +0.172 +0.132 0.217T +0.195 +0.132 0.240T

17.7165 19.6850 -0.0018 +0.0031 +0.0016 0.0016T +0.0043 +0.0027 0.0027T +0.0068 +0.0052 0.0052T +0.0077 +0.0052 0.0052T
0.0049T 0.0061T 0.0086T 0.0095T
(1)
Tolerance range is from +0 to value listed.
NOTE: Tolerance and shaft diameters are shown in the table as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 35
SNT SPLIT PLUMMER BLOCKS
ENGINEERING LUBRICATION

36 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING LUBRICATION

LUBRICATION
To help maintain a bearings antifriction characteristics, lubrication
on
is needed to:
Minimize rolling resistance caused by deformation of the
rolling elements and raceway under load by separating thee
mating surfaces.
Minimize sliding friction occurring between rolling
elements, raceways and cage.
Transfer heat (with oil lubrication).
Protect from corrosion and, with grease lubrication,
from contaminant ingress.

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
General-Purpose Industrial Grease . . . . . . . . . . . . . . . . . . . . . . 45

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 37
SNT SPLIT PLUMMER BLOCKS
ENGINEERING LUBRICATION

LUBRICATION
The wide range of bearing types and operating conditions TABLE 10. COMPOSITION OF GREASES
precludes any simple, all-inclusive statement or guideline
Lubricating
allowing the selection of the proper lubricant. At the design Base Oil + Thickening Agents + Additives =
Grease
level, the rst consideration is whether oil or grease is best for Mineral oil Soaps and complex soaps Rust inhibitors
the particular operation. The advantages of oil and grease are lithium, aluminum,
Synthetic Dyes
barium, calcium
outlined in the table below. When heat must be carried away hydrocarbon
Tactiers
Non-Soap (inorganic)
from the bearing, oil must be used. It is typically preferred for Esters
microgel (clay), Metal
very high-speed applications. Timken SNT housings and seal Peruorinated oil carbon black, deactivates
Silicone silica-gel, PTFE Oxidation
systems are specically designed for grease lubrication. If
Non-Soap (organic) inhibitors
an application requires oil lubrication, contact your Timken Urea compounds Anti-wear EP
engineer for assistance.

TABLE 9. ADVANTAGES OF OIL AND GREASE Calcium- and aluminum-based greases have excellent water
Oil Grease resistance and are used in industrial applications where water
Carries heat away Simplies seal design ingress is an issue. Lithium-based greases are multi-purpose and
from the bearings and acts as a sealant
are used in industrial applications and wheel bearings.
Carries away moisture Permits prelubrication of sealed
and particulate matter or shielded bearings Synthetic base oils such as esters, organic esters and silicones
Generally requires less used with conventional thickeners and additives typically have
Easily controlled lubrication
frequent lubrication higher maximum operating temperatures than petroleum-based
greases. Synthetic greases can be designed to operate in
temperatures from -73 C (-100 F) to 288 C (550 F).
European REACH compliance
In table 11 are the general characteristics of common thickeners
Timken-branded lubricants, greases and similar products sold used with petroleum base oils.
in stand-alone containers or delivery systems are subject to the
Use of the thickeners in table 11 with synthetic hydrocarbon or
European REACH (Registration, Evaluation, Authorization and
ester base oils increases the maximum operating temperature
Restriction of CHemicals) directive. For import into the European
by approximately 10 C (18 F).
Union, Timken can sell and provide only those lubricants and greases
that are registered with ECHA (European CHemical Agency). TABLE 11. GENERAL CHARACTERISTICS OF
For further information, please contact your Timken engineer. THICKENERS USED WITH PETROLEUM-BASED OILS
Typical Maximum
Dropping Point Temperature Typical
Thickener
GREASE LUBRICATION C F C F
Water Resistance

Grease lubrication is generally applicable to low-to-moderate Lithium


193 380 121 250 Good
speed applications that have operating temperatures within the soap

limits of the grease. There is no universal antifriction bearing Lithium


260+ 500+ 149 300 Good
complex
grease. Each grease has limiting properties and characteristics.
Aluminum
249 480 149 300 Excellent
Greases consist of a base oil, a thickening agent and additives. complex
Conventionally, bearing greases have consisted of petroleum Calcium
299 570 177 350 Excellent
sulfonate
base oils thickened to the desired consistency by some form of
Polyurea 260 500 149 300 Good
metallic soap. More recently synthetic base oils have been used
with organic and inorganic thickeners. Table 10 summarizes the
composition of typical lubricating greases. Using polyurea as a thickener for lubricating uids is one of the
most signicant lubrication developments in more than 30 years.
Polyurea grease performance is outstanding in a wide range of
bearing applications.

38 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING LUBRICATION

BASE OILS Viscosity


Base oils are classied as either petroleum types (rened from The selection of oil viscosity for any bearing application requires
crude oil) or synthetic types (produced by chemical synthesis). consideration of several factors: load, speed, bearing setting,
type of oil and environmental factors. Since oil viscosity varies
Petroleum oils inversely with temperature, a viscosity value must always be
Petroleum oils are made from a petroleum hydrocarbon derived stated with the temperature at which it was determined. High-
from crude oil, with additives to improve certain properties. viscosity oil is used for low-speed or high-ambient-temperature
Greases with petroleum oils can be used in most general applications. Low-viscosity oil is used for high-speed or low-
industrial bearing applications and many specialty applications ambient-temperature applications.
with moderate operating temperatures. There are several classications of oils based on viscosity grades.
The most familiar are the Society of Automotive Engineers (SAE)
Synthetic oils classications for automotive engine and gear oils. The American
Synthetic oils cover a broad range or categories and include Society for Testing and Materials (ASTM) and the International
polyalphaolens, silicones, polyglycols and various esters. In Organization for Standardization (ISO) have adopted standard
general, synthetic oils are less prone to oxidation and perform viscosity grades for industrial uids. Fig. 8 shows the viscosity
more efficiently than petroleum oils at extreme hot or cold comparisons of ISO/ASTM with SAE classication systems at
temperatures. Physical properties, such as pressure-viscosity 40 C (104 F).
coefcients, tend to vary between oil types. Use caution when
making oil selections.
The polyalphaolens (PAO) have a hydrocarbon chemistry that
VISCOSITY CLASSIFICATION COMPARISON
parallels petroleum oil both in chemical structures and pressure-
viscosity coefcients. Therefore, PAO oil is mostly used in the
Viscosity Classification Comparison
oil-lubricated applications of bearings when severe temperature 2000 10000
1500 1500 7500
environments (hot and cold) are encountered or when extended
1000 1000 5000
lubricant life is required. 800
250 min.
4000
600 680 3000
The silicone, ester and polyglycol oils have an oxygen-based

Viscosity, Saybolt Universal Seconds (SUS) at 38 C (100 F)


140
460
Kinematic Viscosity, Centistokes (cSt) at 40 C (104 F)

chemistry that is structurally quite different from petroleum 400 2000


300 320 1500
oils and PAO oils. This difference has a profound effect on its
220 90
physical properties where pressure-viscosity coefcients can 200 50 1000
150 150 700
be lower compared to mineral and PAO oils. This means that 40 85W min.
100 100 500
these types of synthetic oils may actually generate a smaller 80 30 400
68
elastohydrodynamic (EHD) lm thickness than a mineral or PAO 60 80W min. 300
46 20
oil of equal viscosity at operating temperature. Reductions in 40 200
bearing fatigue life and increases in bearing wear could result 30 32 150
10W min. 70W min.
22
from this reduction of lubricant lm thickness. 20 5W min. SAE 100
15 15 SAE Gear Oil 75
10 10 Crankcase Oils
60
8
7 50
6
5
4 40
3
WARNING 3
35
2
Failure to observe the following warnings 2 33
could create a risk of death or serious injury. ISO/ASTM
Viscosity Grade

Proper maintenance and handling practices are critical. Fig. 8. Comparison between ISO/ASTM grades
Always follow installation instructions and maintain (ISO 3448/ASTM D2442) and SAE grades
proper lubrication. (SAE J 300-80 for crankcase oils, SAE J 306-81 for
axle and manual transmission oils).

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 39
SNT SPLIT PLUMMER BLOCKS
ENGINEERING LUBRICATION

The ASTM/ISO viscosity grade system for industrial oils is CONSISTENCY


depicted in g. 9 below.
Greases may vary in consistency from semi-uids that are hardly
ISO VISCOSITY SYSTEM thicker than a viscous oil to solid grades almost as hard as a
500000 soft wood.
100000 ISO/ASTM Viscosity System
For Industrial Fluid Lubricants 200000 Consistency is measured by a penetrometer in which a standard
20000 ISO 3448
50000
5000
ASTM D2422 weighted cone is dropped into the grease. The distance the cone
Assumes 90 Viscosity Index
10000 penetrates (measured in tenths of a millimeter in a specic time)
1000 5000
500
is the penetration number.
2000
200 1000 The National Lubricating Grease Institute (NLGI) classication of

Viscosity, Saybolt Universal Seconds (SUS)


500 grease consistency is shown in table 12 below.
Kinematic Viscosity, Centistokes (cSt)

100
50
200
ISO VG TABLE 12. NLGI CLASSIFICATIONS
20 680 100 NLGI Grease Grades Penetration No.
460
320 75 0 355-385
10 ISO/ASTM Grade 220
Designations 1 310-340
150 50
ISO/ASTM Viscosity Range
Viscosity cSt (mm2/s) at 100 2 265-295
5.00 Grade 40 C (104 F)(1) 68
1500 1350-1650 46 40 3 220-250
4.00
1000 900-1100
680 612-748 32 4 175-205
3.00
460 414-506 35
320 288-352 5 130-160
220 198-242
2.00 150 135-165 33 6 85-115
100 90-110
68 61-75
1.50 46 41-51
32 29-35
Grease consistency is not xed, it normally becomes softer
22 20-24 when sheared or worked. In the laboratory, this working is
(1)
Rounded off to the
1.00
nearest whole number accomplished by forcing a perforated plate up and down through
0 50 100 150
a closed container of grease. This working does not compare
Temperature Degrees Celsius
with the violent shearing action that takes place in a bearing and
20 60 100 140 180 220 260 300
does not necessarily correlate with actual performance.
210
Temperature Degrees Fahrenheit

Fig. 9. Viscosity grade system for industrial oils.

40 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING LUBRICATION

LOW TEMPERATURES A rule of thumb, developed from years of testing grease-


lubricated bearings, indicates that grease life is halved for every
Starting torque in a grease-lubricated bearing at low temperatures
10 C (18 F) increase in temperature. For example, if a particular
can be critical. Some greases may function adequately as long
grease provides 2000 hours of life at 90 C (194 F), by raising the
as the bearing is operating, but resistance to initial movement
temperature to 100 C (212 F), reduction in life to approximately
may be excessive. In certain smaller machines, starting may be
1000 hours would result. On the other hand, 4000 hours could be
impossible when very cold. Under such operating circumstances,
expected by lowering the temperature to 80 C (176 F).
greases containing low-temperature characteristic oils are
generally required. Thermal stability, oxidation resistance and temperature limitations
must be considered when selecting greases for high-temperature
If the operating temperature range is wide, synthetic greases
applications. In non-relubricatable applications, highly rened
offer advantages. Synthetic greases are available to provide
mineral oils or chemically stable synthetic uids are required
very low starting and running torque at temperatures as low as
as the oil component of greases for operation at temperatures
-73 C (-100 F). In certain instances, these greases perform better
above 121 C (250 F).
in this respect than oil.
TABLE 13. TEMPERATURE RANGES FOR BASE OILS
An important point concerning lubricating greases is that the USED IN LUBRICATING GREASES
starting torque is not necessarily a function of the consistency
or the channel properties of the grease. Starting torque is more Petroleum
a function of the individual rheological properties of a particular
grease and is best evaluated by application experience. Ester

Synthetic
HIGH TEMPERATURES hydrocarbon

The high temperature limit for lubricating greases is generally Silicone


a function of the thermal and oxidation stability of the uid and
Peruoroalkyl
the effectiveness of the oxidation inhibitors. Grease temperature polyether
ranges are dened by both the dropping point of the grease
-73 C -18 C 38 C 93 C 149 C 204 C 260 C 316 C
thickener and composition of the base oil. Table 13 shows -100 F -0 F 100 F 200 F 300 F 400 F 500 F 600 F
the temperature ranges of various base oils used in grease
formulations.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 41
SNT SPLIT PLUMMER BLOCKS
ENGINEERING LUBRICATION

CONTAMINATION GREASE SELECTION


Abrasive Particles The successful use of bearing grease depends on the physical
and chemical properties of the lubricant as well as application
When roller bearings operate in a clean environment, the primary
and environmental conditions. Because the choice of grease
cause of damage is the eventual fatigue of the surfaces where
for a particular bearing under certain service conditions is often
rolling contact occurs. However, when particle contamination
difcult to make, you should consult with your lubricant supplier
enters the bearing system, it is likely to cause damage such as
or equipment maker for specic questions about lubrication
bruising, which can shorten bearing life.
requirements for your application. You also can contact your
When dirt from the environment or metallic wear debris from Timken engineer for general lubrication guidelines for any
some component in the application are allowed to contaminate application.
the lubricant, wear can become the predominant cause of bearing
Grease must be carefully selected with regard to its consistency
damage. If bearing wear becomes signicant, changes will
at operating temperature. It should not exhibit thickening,
occur to critical bearing dimensions that could adversely affect
separation of oil, acid formation or hardening to any marked
machine operation.
degree. It should be smooth, non-brous and entirely free from
Bearings operating in a contaminated lubricant exhibit a higher chemically active ingredients. Its dropping point should be
initial rate of wear than those running in an uncontaminated considerably higher than the operating temperature.
lubricant. With no further contaminant ingress, this wear rate
quickly diminishes. The contamination particles are reduced PERFORMANCE ENHANCING GREASE
in size as they pass through the bearing contact area during
ADDITIVES
normal operation.
Greases can be enhanced with a variety of base oil and soap
Water additive packages that improve the performance of the grease
Water and moisture can be particularly conducive to bearing and extend the life of the bearing the grease is lubricating. These
damage. Lubricating greases may provide a measure of additive packages can include agents which:
protection from this contamination. Certain greases, such as inhibit oxidation, rust and corrosion
calcium and aluminum-complex, are highly water-resistant. resist water immersion and washout
Sodium-soap greases are water-soluble and should not be used provide anti-wear protection
in applications involving water. allow extreme pressure from extraordinary loading
Either dissolved or suspended water in lubricating oils can exert
a detrimental inuence on bearing fatigue life. Water can cause
bearing etching that also can reduce bearing fatigue life. The
exact mechanism by which water lowers fatigue life is not fully
understood. It has been suggested that water enters micro-
cracks in the bearing rings that are caused by repeated stress
cycles. This leads to corrosion and hydrogen embrittlement in
the micro-cracks, reducing the time required for these cracks
to propagate to an unacceptable-sized spall.
Water-based uids, such as water glycol and invert emulsions,
also have shown a reduction in bearing fatigue life. Although
water from these sources is not the same as contamination,
the results support the previous discussion concerning water-
contaminated lubricants.

42 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING LUBRICATION

Timken application-specic lubricants were developed by leveraging our knowledge of tribology


and antifriction bearings, and how these two elements affect overall system performance. Timken
lubricants help bearings and related components operate effectively in demanding industrial operations.
High-temperature, anti-wear and water-resistant additives offer superior protection in challenging
environments. Table 14 provides an overview of the Timken greases available for general applications.
Contact your Timken engineer for a more detailed publication on Timken lubrication solutions.

TABLE 14. GREASE LUBRICATION SELECTION GUIDE

ENVIRONMENT APPLICATION

High Wear Moderate Loads Timken Premium Agriculture Bushings/Ball Joints


Moderate Speeds All-Purpose Industrial Grease Truck and Auto Wheel Bearings
Moderate Temperatures Part No. GR217 Heavy-Duty Industrial

Agriculture/Mining Cement Plants


Extreme Heat Heavy Loads
Timken Construction and Construction/Off Road Rock Quarry
High Sliding Wear
Off-Highway Grease Earth-Moving Equipment
Dirty Environments
Part No. GR219 Fleet Equipment Heavy Industry
Slow Speeds Shock Loading
Pivot Pins/Splined Shafts

Wet and Corrosive Conditions


Quiet Environments Light Loads Lightly Loaded Pillow Blocks
Timken Ball Bearing
Moderate to High Speeds Idler Pulleys Oven Conveyors
Pillow Block Grease
Moderate Temperatures Electric Motors Fans Pumps
Part No. GR220
Light Load Alternators Generators
Moderate Water

Corrosive Media Extreme Heat Timken Mill Grease Aluminum Mills Paper Mills
Heavy Loads Wet Conditions Part Nos. GR180 - NLGI No. 1 Steel Mills Offshore Rigs
Slow to Moderate Speeds GR182 - NLGI No. 2 Power Generation

Incidental Food Contact


Timken
Hot and Cold Temperatures Food and Beverage Industries
Food Safe Grease
Moderate to High Speeds Pharmaceuticals
Part No. GR231
Medium Loads

Wind Energy Main Bearing


Extreme Low and High Temperatures
Timken Pulp and Paper Machines
Severe Loads
Synthetic Industrial Grease General Heavy Industry
Corrosive Media
Part No. GR232 Marine Applications
Slow to Moderate Speeds
Centralized Grease Systems

Moderate Speeds Timken General Industrial Applications


Light to Moderate Loads Multi-Use Lithium Grease Pins and Bushings Track Rollers
Moderate Temperatures Part Nos. GR236 - NLGI No. 1, EP1 Water Pumps
Moderate Water GR237 - NLGI No. 2, EP2 Plain and Antifriction Bearings

This selection guide is not intended to replace the specications by the equipment builder, who is responsible for its performance.

Many bearing applications require lubricants with special properties or lubricants formulated
specically for certain environments, such as:
Friction oxidation (fretting corrosion).
Chemical and solvent resistance.
Food handling.
For assistance with these or other areas requiring special lubricants, consult your Timken engineer.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 43
SNT SPLIT PLUMMER BLOCKS
ENGINEERING LUBRICATION

GREASE USE GUIDELINES


It is important to use the proper amount of grease in the
application. In typical industrial applications, the bearing cavity
should be kept approximately one-third to one-half full. Less
grease may result in the bearing being starved for lubrication.
More grease may result in churning. Both conditions may result
in excessive heat generation. As the grease temperature rises,
viscosity decreases and the grease becomes thinner. This can
reduce the lubricating effect and increase leakage of the grease
from the bearing. It also may cause the grease components
to separate, leading to a general breakdown of the lubricant
Fig. 10. Grease can easily be Fig. 11. Mechanical grease
properties. As the grease breaks down, bearing torque increases. packed by hand. packer.
In the case of excess grease resulting in churning, torque may
also increase due to the resistance caused by the grease.
Timken offers a range of lubricants to help bearings and
For best results, there should be ample space in the housing related components operate effectively in demanding industrial
to allow room for excess grease to be displaced. However, it operations. High-temperature, anti-wear and water-resistant
is equally important that the grease be retained all around the additives offer greater protection in challenging environments.
bearing. If a large void exists between the bearings, grease Timken also offers a line of single- and multi-point lubricators to
closures should be used to prevent the grease from leaving the simplify grease delivery.
bearing area.
Grease application methods
Frictional torque is inuenced by the quantity and the quality
of lubricant present. Excessive quantities of grease causes Grease, in general, is easier to use than oil in industrial bearing
churning. The adverse effects of churn are accelerated with applications. Most bearings that are initially packed with grease
increases in operating speed. The churn results in excessive require periodic relubrication to operate efciently.
temperatures, separation of the grease components, and Grease should be packed into the bearing so that it gets between
breakdown in lubrication values. In normal-speed applications, the rolling elements and coats raceway surfaces.
the housings should be kept approximately one-third to one-
Grease can be easily packed into small- and medium-size
half full.
bearings by hand (g. 10). In shops where bearings are frequently
Only in low-speed applications may the housing be entirely lled regreased, a mechanical grease packer that forces grease
with grease. This method of lubrication is a safeguard against the through the bearing under pressure may be appropriate (g. 11).
entry of foreign matter, where sealing provisions are inadequate Regardless of the method, after packing the internal areas of the
for exclusion of contaminants or moisture. bearing, a small amount of grease also should be smeared on the
During periods of non-operation, completely lling the housings outside of the rollers.
with grease can provide additional protection to the bearing The two primary considerations that can effect the relubrication
surfaces. Prior to restarting operation, remove the excess grease cycle are operating temperature and sealing efciency. High-
and restore the proper level. operating-temperature applications generally require more
Applications using grease lubrication should have a grease tting frequent regreasing. The less efcient the seals, the greater
and a vent at opposite ends of the housing near the top. A drain the grease loss and the more frequently grease must be added.
plug should be located near the bottom of the housing to allow Grease should be added any time the amount in the bearing
the grease to purge as needed. falls below the desired amount. The grease should be replaced
Bearings should be relubricated at regular intervals to help when its lubrication properties have been reduced through
prevent damage. Relubrication intervals are difcult to determine. contamination, high temperature, water, oxidation or any other
If plant practice or experience with other applications is not factors. It is also important to follow suggested practice for
available, consult your lubricant supplier. seal lubrication. Mounting instructions shown starting on page
55 indicated appropriate methods based on seal and housing
construction.

44 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING GENERAL-PURPOSE INDUSTRIAL GREASE

GENERAL-PURPOSE INDUSTRIAL GREASE


Polyurea and lithium-based greases are typical of greases that They should not contain materials that are corrosive or
can be used to lubricate many Timken bearing applications in all abrasive to bearings or seals. The grease should have excellent
types of standard equipment. Polyurea and lithium-based greases mechanical and chemical stability. The grease should contain
are normally preferred for general-purpose bearing lubrication inhibitors to provide long-term protection against oxidation in
and are advantageous in high moisture applications. Both greases high-performance applications and protect the bearings from
have good water-resistant characteristics. corrosion in the presence of moisture. The suggested base oil
Special consideration should be given to applications where viscosity covers a fairly wide range. Lower viscosity products
speed, load, temperature or environmental conditions are should be used in high-speed and/or lightly loaded applications
extreme. For temperature ranges of standard greases see to minimize heat generation and torque. Higher viscosity products
table 13. should be used in moderate- to low-speed applications and under
heavy loads to maximize lubricant lm thickness.
Lithium greases, lithium complex greases, or calcium sulfonate
thickened grease are suitable for most centralized, single-point, Speed ratings are listed for each size/class part number in
or manually lubricated product. These greases should be smooth, the Timken Spherical Roller Bearing Catalog (order no. 10446)
homogeneous and uniform, premium-quality product composed on pages 59 88. When application speeds exceed 70 percent
of mineral or synthetic oil, a thickener and appropriate inhibitors of grease speed rating, consider increasing RIC by one ISO
(see table 15). clearance range (CNormal to C3). Table 16 is provided as a
reference for typical grease thickener compatibilities. For general
TABLE 15. SUGGESTED LITHIUM SOAP, LITHIUM COMPLEX industrial applications, consider a grease that is NLGI No. 1 or
AND CALCIUM SULFONATE GREASE PROPERTIES
No. 2, with a ISO 150 to 220 viscosity grade.
Thickener type Lithium Complex, or equivalent
Consistency NLGI No.1 or No. 2
NOTE
Additives Anti-wear, corrosion and oxidation inhibitors
Mixing greases can result in improper bearing lubrication.
Base oil Mineral oil or synthetic Always follow the specic lubrication instructions of
Viscosity at 40 C ISO VG 150-220 your equipment supplier.
Viscosity index 80 min.
Pour point -18 C (0 F) max. Consult your lubricant supplier for further information for your
specic requirement.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 45
SNT SPLIT PLUMMER BLOCKS
ENGINEERING GREASE LUBRICATIONS FOR BEARING/HOUSING ASSEMBLIES GENERAL-PURPOSE INDUSTRIAL GREASE

TABLE 16. GREASE COMPATIBILITY CHART

= Best Choice

Non-Soap Clay
Ca 12 Hydroxy

Li 12 Hydroxy
Ca Sulfonate

Polyurea S S
Ba Complex

Ca Stearate

Ca Complex
= Compatible

Al Complex

Li Stearate

Li Complex

Polyurea
= Borderline
= Incompatible

Aluminum Complex

Timken Food Safe

Barium Complex

Calcium Stearate

Calcium 12 Hydroxy

Calcium Complex

Calcium Sulfonate

Timken Premium Mill


Timken Heavy-Duty Moly

Clay Non-Soap

Lithium Stearate

Lithium 12 Hydroxy

Lithium Complex

Polyurea Conventional

Polyurea Shear Stable

Timken Multi-Use

Timken All -Purpose


Timken Synthetic

Timken Pillow Block

46 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
ENGINEERING GREASE LUBRICATIONS FOR BEARING/HOUSING ASSEMBLIES GENERAL-PURPOSE INDUSTRIAL GREASE

APPLICATION CONSIDERATIONS
For higher speed applications (operating at 70 percent of the
grease speed rating or more), a lighter base oil viscosity (ISO
100 150) can be considered. Conversely, for lower speed
applications, a grease with a heavier base oil viscosity (ISO
320 460) can be considered. For lower speed applications
operating at colder start-up temperatures (<-18 C [0 F]), consider
a softer grease (NLGI grade 1) with an approved EP additive. The
lighter grade will allow more grease ow into the bearing contact
area and the EP additive will reduce wear during start-up. An ISO
460 base oil viscosity also can be considered.
When lower speed applications operate at higher temperatures
(>149 C [300 F]), consult your Timken engineer.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 47
SNT SPLIT PLUMMER BLOCKS
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS PRODUCT DATA TABLES

48 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS PRODUCT DATA TABLES

SNT SPHERICAL ROLLER


BEARING PLUMMER BLOCKS
PRODUCT DATA TABLES
Spherical roller bearing plummer blocks combine rugged cast
iron, ductile iron or steel housings with high-capacity bearingss
to meet the toughest demands of industry. Each plummer
block contains an advanced-design spherical roller bearing
with improved geometry and raceway nish for maximized
load capacity and service life. Integrated housing and
bearing features enhance unit lubrication characteristics.
Multiple sealing options protect against contamination.

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Design and Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
SNT Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Load Ratings and Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Installation Guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Two-Bolt SNT Housings For Tapered Bore Bearings . . . . . . .60
Four-Bolt FSNT Housings For Tapered Bore Bearings . . . . . .66
Two-Bolt SNT Housings For Cylindrical Bore Bearings . . . . .70
Four-Bolt FSNT Housings for Cylindrical Bore Bearings . . . .74
Large Plummer Block Housings 3000 And 3100 Series . . . .78
Metric Shaft Diameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 49
SNT SPLIT PLUMMER BLOCKS
NOMENCLATURE

NOMENCLATURE
HOUSING SIZE

Bore code Bore code


HOUSING STYLE

_ SNT _ 5 12 - 6 10
Blank = two-bolt base
F = four-bolt base Housing series:
2 = 200
3 = 300
Blank = cast iron 5 = 500
S = steel 6 = 600
D = ductile iron

SLEEVE(1)

Bore code
LOCATING RING

SR 110 X 10.5 _H 3 10 _
H = adapter sleeve H = oil hole
OH = hydraulic sleeve on nut end

OD (mm) Width (mm)


Sleeve series

(1)
Sleeve assemblies contain adapter sleeve, locknut, and lockwasher

SEAL

Housing size

TABLE 17. TAPERED BORE BEARING EXAMPLE FOR SNT 512-610


Bearing
Locating rings
21310K
SR110X10.5
22310K
SR110X4
22212K
SR110X10
T S N G 6 10
Sleeve H310 H2310 H312
SEAL OPTIONS TSNG = double-lip Bore code

Double-lip TSNG610 TSNG610 TSNG512 LO = labyrinth


with O-ring
LOR LO610 LO610 LO512 Housing series:
VR = V-ring
2 = 200
V-ring VR610 VR610 VR512 TA = taconite 3 = 300
Taconite TA610 TA610 TA512 EC = end cover 5 = 500
6 = 600
End cover EC512-610 EC512-610 EC512-610

Fig. 12. SNT plummer block nomenclature.

50 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
INTRODUCTION DESIGN AND CONSTRUCTION

INTRODUCTION DESIGN AND CONSTRUCTION


Timkens capabilities in engineering and manufacturing heavy-duty Timken offers split plummer block housings that can be built
plummer blocks help ensure high performance from our products. with either tapered bore bearings with adapters for mounting
In addition, Timkens worldwide sales organization is staffed with on straight shafts or cylindrical bore bearings for assembly on
experienced engineers who are available for consultation on shouldered shafts. Each offering includes all the accessories to
any plummer block or bearing application. If your design calls for meet a variety of needs.
shaft sizes or loads not listed in this catalog, contact your Timken Timken uses a system of doweling caps and bases together at
engineer for information about availability of special units. an early stage of manufacturing, so that they remain a single
Sizes: 20 400 mm shafts. unit during machining. They are not interchangeable as separate
parts and become precisely mated components, helping to
Applications: Conveyors, ball mills, casters, rolling mills,
ensure a precise t. Timken supplies plummer block housings
heavy movable structures.
Features: Split construction for convenient assembly and for mounting with two or four bolts.
disassembly. These units include pry-tool slots and multiple Standard caps and bases are made from high-grade, stress-
alignment features to ease installation. There are center
relieved cast iron. They also are available in cast steel and
marks to simplify alignment and dimples for positioning
pins and four-bolt mounting. Seal grooves allow for various ductile iron.
sealing options. The illustration below
Benets: Caps can be removed easily and quickly without (g. 13) shows all parts
damage to the bearing or housing. The design allows for of a plummer block
simplied bearing inspection, service and replacement.
assembly that are
described throughout
Split-block housings
Provide proper support with precision-t matched this section.
cap-and-base with dowel pins. Simplies alignment
and installation of heavy housings. Convenient
pry-tool slots for easy cap removal speeds bearing
inspection and replacement.

Seal options
Protect the bearing with Timken spherical roller bearings
double-lip, labyrinth, Increase reliability with a high-performance
V-ring and taconite bearing that runs cooler for longer bearing life.
sealing options.

Locating rings
Provide exibility to x
or oat the bearing.

Tapered adapter
or straight
bore mounting
Secure each bearing
onto the shaft.

Standard metric
mounting dimensions Cast-iron Optional end caps
Ease installation with same Rugged cast-iron is well-suited Avoid damage to bearing
dimensions as industry for harsh industrial applications. and housing. Easy to install
norms for bolt holes, Available in steel or ductile iron. and remove.
center heights and shaft
diameters. Conforms to
ISO 113:1999.
Fig. 13. SNT plummer block components and features.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 51
SNT SPLIT PLUMMER BLOCKS
MOUNTING

MOUNTING
ADAPTER VERSUS STRAIGHT BORE CLOSED-END INSTALLATIONS
Typically, a spherical roller bearing plummer block assembly In some applications, the shaft end is designed to terminate inside
is mounted on a straight shaft using a tapered bore bearing the plummer block. For this design, positive tting end-cap inserts
and adapter assembly. Standard commercial shafting can be are available to help seal out contaminants and retain lubricant.
used without additional machining. (Suggested shaft diameters Timken heavy-duty end covers provide sealing for closed-end
are shown in table 20 on page 82.) Adapter mount also permits applications.
maximum exibility in the axial positioning of the bearing on Designers and installers need to make sure the shaft end does not
the shaft and will accommodate light locational thrust loads. contact the closure. A minimum of 3 mm clearance at maximum
Timken plummer blocks for tapered bore and cylindrical bore thermal expansion is suggested between the end of the shaft and
are available. the closure. Dimension Y, in the spherical roller bearing tables
Adapter-mounted spherical roller bearings require the correct (pages 85 91), denes the maximum permissible length of the
removal of diametral clearance from the bearing to prevent shaft from the centerline of the plummer block housing.
relative rotation between inner race and sleeve or shaft. For
NOTE
proper shaft mounting of adapter-type spherical roller bearings,
see page 21. Failure to employ proper mounting procedures can cause
reduced bearing performance.
When application conditions produce heavy thrust loads, or a
need exists for exact axial location or a positive shaft interference
t, a direct straight bore mounting may be the best option. This
requires a shouldered shaft, machined for proper t, and a straight
bore bearing. Timken plummer block housings for straight bore
applications are available for use with series 213, 222, 223 and 232.
Suggested ts for shafts in cylindrical bore spherical roller
bearings are shown in the engineering section of this catalog
in table 4 on page 23. For applications involving heavy shock,
vibration, unbalanced rotating loads or other non-standard
conditions, consult your Timken engineer.

FIXED AND FLOAT PLUMMER BLOCKS


SNT split plummer block components include two to six locating
rings allowing for installation at either xed or oat positions on the
shaft. For the xed position, two or more locating rings are used on
one or both sides of the bearing.

52 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
SNT LUBRICATION SEALS

SNT LUBRICATION
Timken plummer block housings are designed for grease lubrication. They also can be modied to
accommodate oil-bath and circulating oil- or oil/air-mist systems. Contact your Timken engineer
for assistance. Please reference the installation guides on pages 55 59 for grease ll information.
Lubrication groove and holes may be provided in the bearing outer ring. This feature, designated
by adding sufx W33 to the bearing number, should be specied whenever re-ordering bearings
for pillow blocks. For bearings with lubrication groove and holes, it is suggested that the fresh
lubricant is fed directly to the center of the bearing between the rows of rollers and distributed
to the rest of the bearing. This helps ensure the used lubricant is purged from the bearing.
Housed units feature multiple dimples that can be used to drill and tap for alternative grease
tting locations as needed.

SEALS
Timken SNT plummer blocks are available with multiple sealing options. Each seal type
incorporates specic features to meet your application needs. Table 18 compares the various
features of each seal type.

DOUBLE-LIP SEALS LABYRINTH SEALS


Double-lip seals are the most common seal Labyrinth seals are made up of a single metal ring component
design used with SNT plummer blocks. These that interconnects with the grooves in the
are general all purpose elastomer seals that housing to form a labyrinth gap. The inside
can protect in moderately contaminated diameter of the metal ring contains an
environments. The seal is split into two 180 O-ring that creates an interference t with
degree halves for easy installation. The seal the shaft so that the ring will rotate with
element runs against the shaft surface and Fig. 14. the shaft. Labyrinth seals can be used on
should be used in grease lubricated blocks. Double-lip seals. high-speed applications and in moderately
Contact your Timken engineer for double-lip seal availability when contaminated environments. Fig. 16.
using cylindrical bore housings. Labyrinth seals.
TACONITE SEALS
V-RING SEALS Taconite seals are a combination of both a labyrinth seal and
V-ring seals are a deector type seal. They are V-ring seal. The labyrinth seal is made up of two separate metal
made up of an elastomer V-ring seal element ring components, inner and outer, that have interconnecting
that rotates with the shaft and runs against the grooves that form a labyrinth gap. The outer metal ring component
axial surface of a washer-type component that contains an O-ring on its outside diameter that provides an
is retained in the block housing. As the V-ring interference t to the groove in the housing. The inside diameter of
element is a stretch t onto the shaft, a rougher the inner metal ring component contains an O-ring that creates an
Fig. 15. shaft surface is acceptable. This seal performs interference t with the shaft
V-ring seals.
well in moderately contaminated environments so that the ring will rotate with
with ne particulate. the shaft. This seal performs
well in highly contaminated
environments such as those
seen in mining operations.

Fig. 17. Taconite seals.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 53
SNT SPLIT PLUMMER BLOCKS
SEALS LOAD RATINGS AND LIFE

TABLE 18. SEAL SELECTION


Seal Selection Double-Lip (TSNG) V-Ring (VR) Labyrinth (LO) Taconite (TA)

Material NBR NBR rubber + mild steel plate Steel + NBR O-ring Steel + NBR O-ring and V-ring

Temperature -40 to 100 C (-40 to 212 F) -40 to 100 C (-40 to 212 F) -40 to 120 C (-40 to 248 F) -40 to 100 C (-40 to 212 F)

Maximum speed 8 m/s 7 m/s Same as bearing 7 m/s

Grease relubrication Excellent Excellent Good Good

Oil lubrication(1) Poor Poor Poor Poor

Low friction Good Good Excellent Good

Resists dust/ne particles Excellent Excellent Good Excellent

Resists coarse particles Good Poor Excellent Good

Resists water Good Good Fair Good

Misalignment
1 1.5 0.3 0.3
Shaft dia. 100 mm

Misalignment
0.5 1 0.3 0.3
Shaft dia. > 100 mm
(1)
If an application requires oil lubrication, please contact your Timken engineer.

LOAD RATINGS AND LIFE


Load ratings for the spherical roller bearings that are used in
plummer blocks are found in the dimension tables on pages
85 through 91. Life calculation formulas are found in the
Engineering Manual (order no. 10424) on page 48 available on
www.timken.com.
In addition to individual bearing selection, the ability of the
plummer block to carry the operating load should be considered.
It should be noted that the load rating gures supplied in this
catalog are applicable only when the load direction is generally
toward the base of the plummer block. If the plummer block must
be mounted so the load can be applied in any other direction,
consult your Timken engineer.

54 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
INSTALLATION GUIDES MOUNTING HOUSINGS WITH DOUBLE-LIP SEALS

INSTALLATION GUIDES
Following are installation guides for the SNT housings and the four seal types offered by Timken.

MOUNTING HOUSINGS WITH DOUBLE-LIP SEALS


Prior to starting installation, please read the following instructions. 6. Mount the bearing on the shaft either directly on a
Contact a Timken engineer with any questions. stepped shaft or using an adapter sleeve. Completely ll
1. Clean the work area. Check the dimensional and form the bearing with grease. The remainder of the suggested
accuracy of the shaft seat. Note: The shaft roundness grease quantity can be placed in the housing, equally
specication should be half of the O.D. tolerance. Ensure distributed on each side of the bearing (See grease ll).
the shaft is free from burrs, gouges or other imperfections. 7. Install the shaft with bearing in the housing base (g. 19a).
2. Ensure the surface roughness of the support surface Ra 8. Put one locating ring on each side of the bearing for
12.5 m. Ensure atness is within 0.08 mm (base) and 0.125 locating bearing arrangements (g. 19b).
mm aggregate (housing base and mounting surface).
9. Carefully align the housing base. Use the vertical markings
3. Determine the position of the housing relative to the adapter at the middle of the side faces and end faces of the housing
sleeve on the shaft for bearings on adapter sleeves. For base to help with this (g. 20a). Then lightly tighten the
bearings that have to be relubricated from the side, the attachment bolts (g. 20b).
grease tting in the housing cap should always face away
10. The remaining seal halves must be inserted in the seal
from the locknut on the adapter sleeve. When housings are
grooves in the housing cap and the space between the
mounted on the end of a shaft, grease must be supplied at
sealing lips lled with grease.
the end cover side. Make sure to position the base correctly
because the cap only ts in one direction. 11. Check the cap and base to see that they show the same
identication. Install the cap onto the base (g. 21a) and
4. Position the housing on the support surface. Fit the
tighten the cap bolts to the torque specied in the table.
attachment bolts but do not tighten them (g. 18a).
12. Fully tighten the attachment bolts in the housing base
5. Insert one seal half in each of the grooves in the housing
(g. 21b). Suggested tightening torques are given in the table.
base. Fill the space between the two sealing lips with
grease (g. 18b). If the housing is used on the end of a shaft, For torque table and grease ll information, please see page 59.
insert an end cover on one side instead of the seal half.
b
Fig. 18 Fig. 19 a
a
b
b
a

b a

Fig. 20 b Fig. 21

b b

a
a

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 55
SNT SPLIT PLUMMER BLOCKS
INSTALLATION GUIDES MOUNTING HOUSINGS WITH LABYRINTH SEALS

MOUNTING HOUSINGS WITH LABYRINTH SEALS


Prior to starting installation, please read the following instructions. grease quantity can be placed in the housing, equally
Contact a Timken engineer with any questions. distributed on each side of the bearing (See grease ll).
1. Clean the work area. Check the dimensional and form 7. Mount the second labyrinth ring on the shaft in the correct
accuracy of the shaft seat. Note: The shaft roundness position (g. 23c). If the housing is to be used on the end
specication should be half of the O.D. tolerance. Ensure of a shaft, omit the second labyrinth ring and insert an end
the shaft is free from burrs, gouges or other imperfections. cover in the housing base instead.
2. Ensure the surface roughness of the support surface 8. Install the shaft with bearing and labyrinth ring(s) in the
Ra 12.5 m. Ensure atness is within 0.08 mm (base) and housing base (g. 24a).
0.125 mm aggregate (housing base and mounting surface). 9. Place one locating ring on each side of the bearing for
3. For bearings on adapter sleeves, determine the position locating bearing arrangements (g. 24b).
of the housing relative to the adapter sleeve on the shaft. 10. Align the housing base. Use the vertical markings at the
For bearings that have to be relubricated from the side, the middle of the side faces and end faces of the housing base
grease tting in the housing cap should always face away to help with this. Tighten the attachment bolts (g. 24c).
from the locknut on the adapter sleeve. Grease should 11. Check the cap and base to see that they have the same
be supplied at the end cover side where housings are identication. Install the cap onto the base (g. 25a) and
mounted on the end of a shaft. Be sure to position the base tighten the cap bolts to the torque specied in the table.
correctly since the cap only ts in one direction.
12. Fully tighten the attachment bolts in the housing base
4. Position the housing on the support surface. Fit the (g. 25b). Suggested tightening torques are given in the table.
attachment bolts but do not tighten them (g. 22).
13. Insert the hollow O-ring cord of synthetic rubber in the
5. Mount the labyrinth ring on the shaft (g. 23a). grooves in the labyrinth rings. Use a screwdriver while
6. Mount the bearing on the shaft either directly on a stepped turning the shaft, take care not to damage the seal (g. 25c).
shaft or using an adapter sleeve (g. 23b). Completely ll
For torque table and grease ll information, please see page 59.
the bearing with grease. The remainder of the suggested

Fig. 22 Fig. 23 a
b

a
a
b
Fig. 24 Fig. 25

56 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
INSTALLATION GUIDES MOUNTING HOUSINGS WITH V-RING SEALS

MOUNTING HOUSINGS WITH V-RING SEALS


Prior to starting installation, please read the following instructions. the bearing with grease. The remainder of the suggested
Contact a Timken engineer with any questions. grease quantity can be placed in the housing, equally
1. Ensure the work area is clean. Check the dimensional and distributed on each side of the bearing (See grease ll).
form accuracy of the shaft seat. Note: The shaft roundness 7. Arrange the second sealing washer and V-ring on the shaft
specication should be half of the O.D. tolerance. Ensure at the other side of the bearing (g. 27c). If the housing is to
the shaft is free from burrs, gouges or other imperfections. be used on the end of a shaft, mount an end cover instead.
2. Ensure the surface roughness of the support surface 8. Install the shaft with bearing and sealing washers in the
Ra 12.5 m. Ensure atness is within 0.08 mm (base) and housing base (g. 28a).
0.125 mm aggregate (housing base and mounting surface).
9. Put one locating ring on each side of the bearing for
3. Determine the position of the housing relative to the adapter locating bearing arrangements.
sleeve on the shaft for bearings on adapter sleeves. For
10. Align the housing base. Use the vertical markings at the
bearings that have to be relubricated from the side, the
middle of the side faces and end faces of the housing base to
grease tting in the housing cap should always face away
help with this. Lightly tighten the attachment bolts (g. 28b).
from the locknut on the adapter sleeve. Grease should
be supplied at the end cover side where housings are 11. Check the cap and base to see that they bear the same
mounted on the end of a shaft. Make sure to position the identication. Install the cap onto the base and tighten the
base correctly since the cap only ts in one direction. cap bolts to the torque marked in the table (g. 29a).

4. Position the housing on the support surface. Fit the 12. Tighten the attachment bolts in the housing base (g. 29b).
attachment bolts but do not tighten them (g. 26). Check the table for suggested tightening torques.

5. Arrange the one V-ring with sealing washer on the shaft. 13. Coat the V-ring counterfaces on the sealing washers with
The V-ring should be furthest away from the bearing and grease (g. 29c).
seal against the washer, i.e. the lip should point inward the 14. Finally, push the V-ring seals into their correct position.
washer (g. 27a). This can be done using a punch or screwdriver to push the
6. Mount the bearing on the shaft either directly on a stepped seal as the shaft is turned, take care not to damage the
shaft or using an adapter sleeve (g. 27b). Completely ll seal (g. 30).

For torque table and grease ll information, please see page 59.
Fig. 26 Fig. 27 b a Fig. 28 a

Fig. 29 Fig. 30

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 57
SNT SPLIT PLUMMER BLOCKS
INSTALLATION GUIDES MOUNTING HOUSINGS WITH TACONITE SEALS

MOUNTING HOUSINGS WITH TACONITE SEALS


Prior to starting installation, please read the following instructions. with grease. The remainder of the suggested grease
Contact a Timken engineer with any questions. quantity can be placed in the housing, equally distributed
1. Ensure the work area is clean. Check the dimensional and on each side of the bearing (See grease ll).
form accuracy of the shaft seat. Note: The shaft roundness 7. Mount the second seal according to step 5 (g. 32d). If the
specication should be half of the O.D. tolerance. Ensure housing is to be used on the end of a shaft, omit the second
the shaft is free from burrs, gouges or other imperfections. seal and insert an end cover in the housing base instead.
2. Ensure the surface roughness of the support surface 8. Use the hollow O-section cord to x the labyrinth ring in
Ra 12.5 m (500 in). Ensure atness is within 0.08 mm position on the shaft (g. 32c). Use a screwdriver to t the
(base) and 0.125 mm aggregate (housing base and cords while rotating the shaft, taking care not to damage
mounting surface). the cords. Mount the O-rings on the seal outer diameter.
3. For bearings on adapter sleeves, determine the position 9. Install the shaft with bearing and seals in the housing base
of the housing relative to the adapter sleeve on the shaft. (g. 33a) taking care that the hollow O-section cords are
For bearings that have to be relubricated from the side, the not damaged.
grease tting in the housing cap should always face away
from the locknut on the adapter sleeve. Where housings are 10. For locating bearing arrangements put one locating ring on
mounted on the end of a shaft, grease should be supplied each side of the bearing.
at the end cover side. Be sure to position the base correctly 11. Carefully align the housing base. Use the vertical markings
since the cap only ts in one direction. at the middle of the side faces and end faces of the housing
4. Position the housing on the support surface. Fit the base to help facilitate this (g. 33b). Tighten the attachment
attachment bolts but do not tighten them (g. 31). bolts (g. 33c).

5. Mount the rst V-ring together with one labyrinth ring on 12. Check the cap and base to make sure they have the same
the shaft in the correct position (g. 32a). The lip of the identication. Install the cap onto the base (g. 34a) and
V-ring should point towards the bearing. Place the split tighten the cap bolts to the torque specied in the table.
ring parts over the V-ring and labyrinth ring and screw 13. Fully tighten the attachment bolts in the housing base
them together (g. 32b). The two parts of this split ring (g. 34b). Suggested tightening torques are given in the table.
are not interchangeable. Check to see that they carry the 14. Finally, before the rst test run, rotate the shaft and supply
same identication. grease via the tting until it purges from the labyrinth rings
6. Mount the bearing on the shaft (g. 32c) either directly on (g. 34c). Use the same grease for the bearing and the
a stepped shaft or using an adapter sleeve. Fill the bearing labyrinth rings.
b a
Fig. 31 Fig. 32 c Fig. 33

c
e

a b
c
Fig. 34 a b

58 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
GREASE FILL TORQUE TABLES

GREASE FILL
For normal industrial applications, ll bearing void to 100 percent and housing void to
40 60 percent.
For low-speed applications (less than 20 RPM), ll bearing void to 100 percent and housing
void to 60 100 percent.
For high-speed applications (above 70 percent of the bearings thermal speed rating), ll
bearing void to 100 percent and housing void to 30 40 percent.
Contact a Timken engineer with any questions.

ADDITIONAL REFERENCE FOR BEARING MOUNTING


Timken Industrial Maintenance Manual (order no. 10213), Timken Spherical Roller Bearing
Catalog (order no. 10446), pages 14 41 or www.timken.com.

TABLE 19. TIGHTENING TORQUE CAP BOLTS AND


ATTACHMENT BOLTS
Cap Bolts Attachment Bolts
Housing SNT Bolt Size Torque Bolt Size Torque WARNING
Nm Nm Failure to observe the following warnings
505, 205 M10x40 50 M12 80
could create a risk of death or serious injury.
505-605-206-305 M10x40 50 M12 80
Proper maintenance and handling practices are critical.
507-606, 207 M10x50 50 M12 80
Always follow installation instructions and
508-607, 208-307 M10x50 50 M12 80 maintain proper lubrication.
509, 209 M10x50 50 M12 80
Overheated bearings can ignite explosive atmospheres.
510-60, 208-307 M10x55 50 M12 80 Special care must be taken to properly select, install,
511-609, 211 M12x60 80 M16 200 maintain, and lubricate housed unit bearings that are used
in or near atmospheres that may contain explosive levels
512-610, 212 M12x60 80 M16 200 of combustible gases or accumulations of dust such as
513-611,213 M12x65 80 M16 200 from grain, coal, or other combustible materials. Consult
515-612, 215 M12x65 80 M16 200 your equipment designer or supplier for installation and
maintenance instructions.
516-613, 216 M12x70 80 M20 385
517, 217 M12x80 80 M20 385
518-615, 218 M16x19 150 M20 385 CAUTION
519-616 M16x19 150 M20 385 Failure to follow these cautions
could create a risk of injury.
520-617 M20x200 200 M24 665
522-619 M20x100 200 M24 665
If a hammer and bar are used for installation or removal of a
524-620 M20x110 200 M24 665 part, use a mild steel bar (e.g., 1010 or 1020 grade). Mild steel
526 M24x130 350 M24 665 bars are less likely to cause release of high speed fragments
528 M24x130 350 M30 1310
from the hammer or bar or the part being removed.
530 M24x130 350 M30 1310
532 M24x130 350 M30 1310 CAUTION
Failure to follow these cautions
may result in property damage.

Do not use damaged housed units. The use of a damaged


housed unit can result in equipment damage and/or injury.

This information is not intended to substitute for the specic


recommendations of your equipment suppliers.
Every reasonable effort has been made to ensure the accuracy
of the information contained in this writing, but no liability is
accepted for errors, omissions or for any other reason.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 59
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR TAPERED BORE BEARINGS

TWO-BOLT SNT HOUSINGS FOR TAPERED BORE BEARINGS


The basic numbers for ordering plummer block housings Housings shown are furnished in cast iron. If cast steel is
and components are listed in the table below. desired, add the letter S to the alpha prex (e.g., SNTS 518).
Each housing includes the housing cap, base and cap bolts. If ductile iron is desired, add the letter D to the alpha prex
(e.g., SNTD 505).

Double-Lip Seal V-Ring Seal Labyrinth Seal Taconite Seal

Shaft Locating Adapter Double-Lip V-Ring Labyrinth Taconite


Housing Bearing Locknut (3) Lockwasher (3) End Cover (3)
Dia. Rings (1) Sleeve (2) Seal (4) Seal (4) Seal (3) Seal (3)

d O.D. x Width
mm

SNT 505 22205K SR52X3.5 H305 KM5 MB5 VR505 LO505 TA505 EC505
20
SNT 506-605 21305K SR62X7.5 H305 KM5 MB5 TSNG605 VR605 LO605 TA605 EC506-605

SNT 506-605 22206K SR62X6 H306 KM6 MB6 VR506 LO506 TA506 EC506-605
25
SNT 507-606 21306K SR72X7.5 H306 KM6 MB6 TSNG606 VR606 LO606 TA606 EC507-606

SNT 507-606 22207K SR72X5.5 H307 KM7 MB7 TSNG507 VR507 LO507 TA507 EC507-606
30
SNT 508-607 21307K SR80X9 H307 KM7 MB7 TSNG607 VR607 LO607 TA607 EC508-607

SNT 508-607 22208K SR80X8 H308 KM8 MB8 TSNG508 VR508 LO508 TA508 EC508-607
35 SNT 510-608 21308K SR90X9 H308 KM8 MB8 TSNG608 VR608 LO608 TA608 EC510-608
SNT 510-608 22308K SR90X4 H2308 KM8 MB8 TSNG608 VR608 LO608 TA608 EC510-608

SNT 509 22209K SR85X3.5 H309 KM9 MB9 TSNG509 VR509 LO509 TA509 EC509
40 SNT 511-609 21309K SR100X9.5 H309 KM9 MB9 TSNG609 VR609 LO609 TA609 EC511-609
SNT 511-609 22309K SR100X4 H2309 KM9 MB9 TSNG609 VR609 LO609 TA609 EC511-609

SNT 510-608 22210K SR90X9 H310 KM10 MB10 TSNG510 VR510 LO510 TA510 EC510-608
45 SNT 512-610 21310K SR110X10.5 H310 KM10 MB10 TSNG610 VR610 LO610 TA610 EC512-610
SNT 512-610 22310K SR110X4 H2310 KM10 MB10 TSNG610 VR610 LO610 TA610 EC512-610

SNT 511-609 22211K SR100X9.5 H311 KM11 MB11 TSNG511 VR511 LO511 TA511 EC511-609
50 SNT 513-611 21311K SR120X11 H311 KM11 MB11 TSNG611 VR611 LO611 TA611 EC513-611
SNT 513-611 22311K SR120X4 H2311 KM11 MB11 TSNG611 VR611 LO611 TA611 EC513-611
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Adapter sleeve assembly includes one sleeve, one locknut and one lockwasher.
(3)
Labyrinth, taconite seal, end cover, locknut, lockwasher, sold one piece per box.
(4)
Double-lip and V-ring seals sold two pieces per box.

60 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR TAPERED BORE BEARINGS

2 Bolts
Housing Dimensions
Reqd
Housing
Mass

A A1 A2 A3 H H1 H2 J min J J max L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg

67 46 80 130 74 40 19 123 130 137 165 15 20 12 1.5


77 52 89 135 89 50 22 143 150 157 185 15 20 12 2.0

77 52 89 135 89 50 22 143 150 157 185 15 20 12 2.0


82 52 94 140 93 50 22 143 150 157 185 15 20 12 2.2

82 52 94 140 93 50 22 143 150 157 185 15 20 12 2.2


85 60 97 145 108 60 25 165 170 175 205 15 20 12 2.9

85 60 97 145 108 60 25 165 170 175 205 15 20 12 2.9


90 60 102 150 113 60 25 165 170 175 205 15 20 12 3.2
90 60 102 150 113 60 25 165 170 175 205 15 20 12 3.2

85 60 97 150 109 60 25 165 170 175 205 15 20 12 2.9


95 70 107 155 128 70 28 205 210 215 255 18 24 16 4.5
95 70 107 155 128 70 28 205 210 215 255 18 24 16 4.5

90 60 102 150 113 60 25 165 170 175 205 15 20 12 3.2


105 70 117 165 134 70 30 205 210 215 255 18 24 16 5.3
105 70 117 165 134 70 30 205 210 215 255 18 24 16 5.3

95 70 107 155 128 70 28 205 210 215 255 18 24 16 4.5


110 80 122 170 150 80 30 224 230 236 275 18 24 16 6.6
110 80 122 170 150 80 30 224 230 236 275 18 24 16 6.6

Continued on next page.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 61
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR TAPERED BORE BEARINGS

TWO-BOLT SNT HOUSINGS FOR TAPERED BORE BEARINGS continued


The basic numbers for ordering plummer block housings Housings shown are furnished in cast iron. If cast steel is
and components are listed in the table below. desired, add the letter S to the alpha prex (e.g., SNTS 518).
Each housing includes the housing cap, base and cap bolts. If ductile iron is desired, add the letter D to the alpha prex
(e.g., SNTD 505).

Double-Lip Seal V-Ring Seal Labyrinth Seal Taconite Seal

Continued from previous page.

Shaft Locating Adapter Double-Lip V-Ring Labyrinth Taconite


Housing Bearing Locknut (3) Lockwasher (3) End Cover (3)
Dia. Rings (1) Sleeve (2) Seal (4) Seal (4) Seal (3) Seal (3)

d O.D. x Width
mm

SNT 512-610 22212K SR110X10 H312 KM12 MB12 TSNG512 VR512 LO512 TA512 EC512-610
55 SNT 515-612 21312K SR130X12.5 H312 KM12 MB12 TSNG612 VR612 LO612 TA612 EC515-612
SNT 515-612 22312K SR130X5 H2312 KM12 MB12 TSNG612 VR612 LO612 TA612 EC515-612

SNT 513-611 22213K SR120X10 H313 KM13 MB13 TSNG513 VR513 LO513 TA513 EC513-611
60 SNT 516-613 21313K SR140X12.5 H313 KM13 MB13 TSNG613 VR613 LO613 TA613 EC516-613
SNT 516-613 22313K SR140X5 H2313 KM13 MB13 TSNG613 VR613 LO613 TA613 EC516-613

SNT 515-612 22215K SR130X12.5 H315 KM15 MB15 TSNG515 VR515 LO515 TA515 EC515-612
65 SNT 518-615 21315K SR160X14 H315 KM15 MB15 TSNG615 VR615 LO615 TA615 EC518-615
SNT 518-615 22315K SR160X5 H2315 KM15 MB15 TSNG615 VR615 LO615 TA615 EC518-615

SNT 516-613 22216K SR140X12.5 H316 KM16 MB16 TSNG516 VR516 LO516 TA516 EC516-613
70 SNT 519-616 21316K SR170X14.5 H316 KM16 MB16 TSNG616 VR616 LO616 TA616 EC519-616
SNT 519-616 22316K SR170X5 H2316 KM16 MB16 TSNG616 VR616 LO616 TA616 EC519-616

SNT 517 22217K SR150X12.5 H317 KM17 MB17 TSNG517 VR517 LO517 TA517 EC517
75 SNT 520-617 21317K SR180X14.5 H317 KM17 MB17 TSNG617 VR617 LO617 TA617 EC520-617
SNT 520-617 22317K SR180X5 H2317 KM17 MB17 TSNG617 VR617 LO617 TA617 EC520-617

SNT 518-615 22218K SR160X12.5 H318 KM18 MB18 TSNG518 VR518 LO518 TA518 EC518-615
80
SNT 518-615 23218K SR160X6.25 H2318 KM18 MB18 TSNG518 VR518 LO518 TA518 EC518-615

SNT 519-616 22219K SR170X12.5 H319 KM19 MB19 TSNG519 VR519 LO519 TA519 EC519-616
85 SNT 522-619 21319K SR200X17.5 H319 KM19 MB19 TSNG619 VR619 LO619 TA619 EC522-619
SNT 522-619 22319K SR200X6.5 H2319 KM19 MB19 TSNG619 VR619 LO619 TA619 EC522-619
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Adapter sleeve assembly includes one sleeve, one locknut and one lockwasher.
(3)
Labyrinth, taconite seal, end cover, locknut, lockwasher, sold one piece per box.
(4)
Double-lip and V-ring seals sold two pieces per box.

62 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR TAPERED BORE BEARINGS

2 Bolts
Housing Dimensions
Reqd
Housing
Mass

A A1 A2 A3 H H1 H2 J min J J max L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg

105 70 117 165 134 70 30 205 210 215 255 18 24 16 5.3


115 80 127 175 156 80 30 222 230 238 280 18 24 16 6.9
115 80 127 175 156 80 30 222 230 238 280 18 24 16 6.9

110 80 122 170 150 80 30 224 230 236 275 18 24 16 6.6


120 90 138 180 177 95 32 252 260 268 315 22 28 20 9.7
120 90 138 180 177 95 32 252 260 268 315 22 28 20 9.7

115 80 127 175 156 80 30 222 230 238 280 18 24 16 6.9


140 100 158 225 194 100 35 285 290 295 345 22 28 20 13.1
140 100 158 225 194 100 35 285 290 295 345 22 28 20 13.1

120 90 138 180 177 95 32 252 260 268 315 22 28 20 9.7


145 100 163 220 212 112 35 285 290 295 345 22 28 20 14.0
145 100 163 220 212 112 35 285 290 295 345 22 28 20 14.0

125 90 143 210 183 95 32 252 260 268 320 22 28 20 10.4


160 110 178 235 218 112 40 314 320 326 380 26 32 24 17.6
160 110 178 235 218 112 40 314 320 326 380 26 32 24 17.6

140 100 158 225 194 100 35 285 290 295 345 22 28 20 13.1
140 100 158 225 194 100 35 285 290 295 345 22 28 20 13.1

145 100 163 220 212 112 35 285 290 295 345 22 28 20 14.0
175 120 191 250 242 125 45 356 344 350 410 32 26 24 22.3
175 120 191 250 242 125 45 344 350 356 410 26 32 24 22.3

Continued on next page.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 63
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR TAPERED BORE BEARINGS

TWO-BOLT SNT HOUSINGS FOR TAPERED BORE BEARINGS continued


The basic numbers for ordering plummer block housings Housings shown are furnished in cast iron. If cast steel is
and components are listed in the table below. desired, add the letter S to the alpha prex (e.g., SNTS 518).
Each housing includes the housing cap, base and cap bolts. If ductile iron is desired, add the letter D to the alpha prex
(e.g., SNTD 505).

Double-Lip Seal V-Ring Seal Labyrinth Seal Taconite Seal

Continued from previous page.

Shaft Locating Adapter Double-Lip V-Ring Labyrinth Taconite


Housing Bearing Locknut (3) Lockwasher (3) End Cover (3)
Dia. Rings (1) Sleeve (2) Seal (4) Seal (4) Seal (3) Seal (3)

d O.D. x Width
mm

SNT 520-617 22220K SR180X12 H320 KM20 MB20 TSNG520 VR520 LO520 TA520 EC520-617
SNT 520-617 23220K SR180X4.85 H2320 KM20 MB20 TSNG520 VR520 LO520 TA520 EC520-617
90
SNT 524-620 21320K SR215X19.5 H2320 KM20 MB20 TSNG620 VR620 LO620 TA620 EC524-620
SNT 524-620 22320K SR215X6.5 H2320 KM20 MB20 TSNG620 VR620 LO620 TA620 EC524-620

SNT 522-619 22222K SR200X13.5 H322 KM22 MB22 TSNG522 VR522 LO522 TA522 EC522-619
100
SNT 522-619 23222K SR200X5.1 H2322 KM22 MB22 TSNG522 VR522 LO522 TA522 EC522-619

SNT 524-620 22224K SR215X14 H3124 KM24 MB24 TSNG524 VR524 LO524 TA524 EC524-620
110
SNT 524-620 23224K SR215X5 H2324 KM24 MB24 TSNG524 VR524 LO524 TA524 EC524-620

SNT 526 22226K SR230X13 H3126 KM26 MB26 TSNG526 VR526 LO526 TA526 EC526
115
SNT 526 23226K SR230X5 H2326 KM26 MB26 TSNG526 VR526 LO526 TA526 EC526

SNT 528 22228K SR250X15 H3128 KM28 MB28 TSNG528 VR528 LO528 TA528 EC528
125
SNT 528 23228K SR250X5 H2328 KM28 MB28 TSNG528 VR528 LO528 TA528 EC528

SNT 530 22230K SR270X16.5 H3130 KM30 MB30 TSNG530 VR530 LO530 TA530 EC530
135
SNT 530 23230K SR270X5 H2330 KM30 MB30 TSNG530 VR530 LO530 TA530 EC530

SNT 532 22232K SR290X17 H3132 KM32 MB32 TSNG532 VR532 LO532 TA532 EC532
140
SNT 532 23232K SR290X5 H2332 KM32 MB32 TSNG532 VR532 LO532 TA532 EC532
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Adapter sleeve assembly includes one sleeve, one locknut and one lockwasher.
(3)
Labyrinth, taconite seal, end cover, locknut, lockwasher, sold one piece per box.
(4)
Double-lip and V-ring seals sold two pieces per box.

64 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR TAPERED BORE BEARINGS

2 Bolts
Housing Dimensions
Reqd
Housing
Mass

A A1 A2 A3 H H1 H2 J min J J max L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg

160 110 178 235 218 112 40 314 320 326 380 26 32 24 17.6
160 110 178 235 218 112 40 314 320 326 380 26 32 24 17.6
185 120 199 260 271 140 45 344 350 356 410 26 32 24 26.5
185 120 199 260 271 140 45 344 350 356 410 26 32 24 26.5

175 120 191 250 242 125 45 344 350 356 410 26 32 24 22.3
175 120 191 250 242 125 45 344 350 356 410 26 32 24 22.3

185 120 199 260 271 140 45 344 350 356 410 26 32 24 26.5
185 120 199 260 271 140 45 344 350 356 410 26 32 24 26.5

190 130 208 265 290 150 50 373 380 387 445 28 35 24 34.0
190 130 208 265 290 150 50 373 380 387 445 28 35 24 34.0

205 150 223 285 302 150 50 413 420 427 500 35 42 30 39.0
205 150 223 285 302 150 50 413 420 427 500 35 42 30 39.0

220 160 241 295 323 160 60 443 450 457 530 35 42 30 48.0
220 160 241 295 323 160 60 443 450 457 530 35 42 30 48.0

235 160 254 315 344 170 60 463 470 477 550 35 42 30 54.5
235 160 254 315 344 170 60 463 470 477 550 35 42 30 54.5

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 65
SNT SPLIT PLUMMER BLOCKS
FOUR-BOLT FSNT HOUSINGS FOR TAPERED BORE BEARINGS

FOUR-BOLT FSNT HOUSINGS FOR TAPERED BORE BEARINGS


The basic numbers for ordering plummer block housings Assemblies shown are furnished in cast iron. If cast
and components are listed in the table below. steel is desired, add the letter S to the alpha prex
Each housing includes the housing cap, base and cap bolts. (e.g., FSNTS 518). If ductile iron is desired, add the
letter D to the alpha prex (e.g., FSNTD 505).

Double-Lip Seal V-Ring Seal Labyrinth Seal Taconite Seal

Shaft Locating Adapter Double-Lip V-Ring Labyrinth Taconite


Housing Bearing Locknut (3) Lockwasher (3) End Cover (3)
Dia. Rings (1) Sleeve (2) Seal (4) Seal (4) Seal (3) Seal (3)

d O.D. x Width
mm

FSNT 511-609 21309K SR100X9.5 H309 KM9 MB9 TSNG609 VR609 LO609 TA609 EC511-609
40
FSNT 511-609 22309K SR100X4 H2309 KM9 MB9 TSNG609 VR609 LO609 TA609 EC511-609

FSNT 512-610 21310K SR110X10.5 H310 KM10 MB10 TSNG610 VR610 LO610 TA610 EC512-610
45
FSNT 512-610 22310K SR110X4 H2310 KM10 MB10 TSNG610 VR610 LO610 TA610 EC512-610

FSNT 511-609 22211K SR100X9.5 H311 KM11 MB11 TSNG511 VR511 LO511 TA511 EC511-609
50 FSNT 513-611 21311K SR120X11 H311 KM11 MB11 TSNG611 VR611 LO611 TA611 EC513-611
FSNT 513-611 22311K SR120X4 H2311 KM11 MB11 TSNG611 VR611 LO611 TA611 EC513-611

FSNT 512-610 22212K SR110X10 H312 KM12 MB12 TSNG512 VR512 LO512 TA512 EC512-610
55 FSNT 515-612 21312K SR130X12.5 H312 KM12 MB12 TSNG612 VR612 LO612 TA612 EC515-612
FSNT 515-612 22312K SR130X5 H2312 KM12 MB12 TSNG612 VR612 LO612 TA612 EC515-612

FSNT 513-611 22213K SR120X10 H313 KM13 MB13 TSNG513 VR513 LO513 TA513 EC513-611
60 FSNT 516-613 21313K SR140X12.5 H313 KM13 MB13 TSNG613 VR613 LO613 TA613 EC516-613
FSNT 516-613 22313K SR140X5 H2313 KM13 MB13 TSNG613 VR613 LO613 TA613 EC516-613

FSNT 515-612 22215K SR130X12.5 H315 KM15 MB15 TSNG515 VR515 LO515 TA515 EC515-612
65 FSNT 518-615 21315K SR160X14 H315 KM15 MB15 TSNG615 VR615 LO615 TA615 EC518-615
FSNT 518-615 22315K SR160X5 H2315 KM15 MB15 TSNG615 VR615 LO615 TA615 EC518-615

FSNT 516-613 22216K SR140X12.5 H316 KM16 MB16 TSNG516 VR516 LO516 TA516 EC516-613
70 FSNT 519-616 21316K SR170X14.5 H316 KM16 MB16 TSNG616 VR616 LO616 TA616 EC519-616
FSNT 519-616 22316K SR170X5 H2316 KM16 MB16 TSNG616 VR616 LO616 TA616 EC519-616

FSNT 517 22217K SR150X12.5 H317 KM17 MB17 TSNG517 VR517 LO517 TA517 EC517
75 FSNT 520-617 21317K SR180X14.5 H317 KM17 MB17 TSNG617 VR617 LO617 TA617 EC520-617
FSNT 520-617 22317K SR180X5 H2317 KM17 MB17 TSNG617 VR617 LO617 TA617 EC520-617
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Adapter sleeve assembly includes one sleeve, one locknut and one lockwasher.
(3)
Labyrinth, taconite seal, end cover, locknut, lockwasher, sold one piece per box.
(4)
Double-lip and V-ring seals sold two pieces per box.

66 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
FOUR-BOLT FSNT HOUSINGS FOR TAPERED BORE BEARINGS

N1

N
J1 A1

J
J2

4 Bolts
Housing Dimensions
Reqd
Housing
Mass

A A1 A2 A3 H H1 H2 J J1 J2 L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg

95 70 107 155 128 70 28 210 35 234 255 15 20 12 4.5


95 70 107 155 128 70 28 210 35 234 255 15 20 12 4.5

105 70 117 165 134 70 30 210 35 234 255 15 20 12 5.3


105 70 117 165 134 70 30 210 35 234 255 15 20 12 5.3

95 70 107 155 128 70 28 210 35 234 255 15 20 12 4.5


110 80 122 170 150 80 30 230 40 252 275 15 20 12 6.6
110 80 122 170 150 80 30 230 40 252 275 15 20 12 6.6

105 70 117 165 134 70 30 210 35 234 255 15 20 12 5.3


115 80 127 175 156 80 30 230 40 257 280 15 20 12 6.9
115 80 127 175 156 80 30 230 40 257 280 15 20 12 6.9

110 80 122 170 150 80 30 230 40 252 275 15 20 12 6.6


120 90 138 180 177 95 32 260 50 288 315 18 24 16 9.7
120 90 138 180 177 95 32 260 50 288 315 18 24 16 9.7

115 80 127 175 156 80 30 230 40 257 280 15 20 12 6.9


140 100 158 225 194 100 35 290 50 317 345 18 24 16 13.1
140 100 158 225 194 100 35 290 50 317 345 18 24 16 13.1

120 90 138 180 177 95 32 260 50 288 315 18 24 16 9.7


145 100 163 220 212 112 35 290 50 317 345 18 24 16 14.0
145 100 163 220 212 112 35 290 50 317 345 18 24 16 14.0

125 90 143 210 183 95 32 260 50 292 320 18 24 16 10.4


160 110 178 235 218 112 40 320 60 348 380 18 24 16 17.6
160 110 178 235 218 112 40 320 60 348 380 18 24 16 17.6

Continued on next page.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 67
SNT SPLIT PLUMMER BLOCKS
FOUR-BOLT FSNT HOUSINGS FOR TAPERED BORE BEARINGS

FOUR-BOLT FSNT HOUSINGS FOR TAPERED BORE BEARINGS continued


The basic numbers for ordering plummer block housings Assemblies shown are furnished in cast iron. If cast
and components are listed in the table below. steel is desired, add the letter S to the alpha prex
Each housing includes the housing cap, base and cap bolts. (e.g., FSNTS 518). If ductile iron is desired, add the
letter D to the alpha prex (e.g., FSNTD 505).

Double-Lip Seal V-Ring Seal Labyrinth Seal Taconite Seal

Continued from previous page.

Shaft Locating Adapter Double-Lip V-Ring Labyrinth Taconite


Housing Bearing Locknut (3) Lockwasher (3) End Cover (3)
Dia. Rings (1) Sleeve (2) Seal (4) Seal (4) Seal (3) Seal (3)

d O.D. x Width
mm

FSNT 518-615 22218K SR160X12.5 H318 KM18 MB18 TSNG518 VR518 LO518 TA518 EC518-615
80
FSNT 518-615 23218K SR160X6.25 H2318 KM18 MB18 TSNG518 VR518 LO518 TA518 EC518-615

FSNT 519-616 22219K SR170X12.5 H319 KM19 MB19 TSNG519 VR519 LO519 TA519 EC519-616
85 FSNT 522-619 21319K SR200X17.5 H319 KM19 MB19 TSNG619 VR619 LO619 TA619 EC522-619
FSNT 522-619 22319K SR200X6.5 H2319 KM19 MB19 TSNG619 VR619 LO619 TA619 EC522-619

FSNT 520-617 22220K SR180X12 H320 KM20 MB20 TSNG520 VR520 LO520 TA520 EC520-617
FSNT 520-617 23220K SR180X4.85 H2320 KM20 MB20 TSNG520 VR520 LO520 TA520 EC520-617
90
FSNT 524-620 21320K SR215X19.5 H320 KM20 MB20 TSNG620 VR620 LO620 TA620 EC524-620
FSNT 524-620 22320K SR215X6.5 H2320 KM20 MB20 TSNG620 VR620 LO620 TA620 EC524-620

FSNT 522-619 22222K SR200X13.5 H322 KM22 MB22 TSNG522 VR522 LO522 TA522 EC522-619
100
FSNT 522-619 23222K SR200X5.1 H2322 KM22 MB22 TSNG522 VR522 LO522 TA522 EC522-619

FSNT 524-620 22224K SR215X14 H3124 KM24 MB24 TSNG524 VR524 LO524 TA524 EC524-620
110
FSNT 524-620 23224K SR215X5 H2324 KM24 MB24 TSNG524 VR524 LO524 TA524 EC524-620

FSNT 526 22226K SR230X13 H3126 KM26 MB26 TSNG526 VR526 LO526 TA526 EC526
115
FSNT 526 23226K SR230X5 H2326 KM26 MB26 TSNG526 VR526 LO526 TA526 EC526

FSNT 528 22228K SR250X15 H3128 KM28 MB28 TSNG528 VR528 LO528 TA528 EC528
125
FSNT 528 23228K SR250X5 H2328 KM28 MB28 TSNG528 VR528 LO528 TA528 EC528

FSNT 530 22230K SR270X16.5 H3130 KM30 MB30 TSNG530 VR530 LO530 TA530 EC530
135
FSNT 530 23230K SR270X5 H2330 KM30 MB30 TSNG530 VR530 LO530 TA530 EC530

FSNT 532 22232K SR290X17 H3132 KM32 MB32 TSNG532 VR532 LO532 TA532 EC532
140
FSNT 532 23232K SR290X5 H2332 KM32 MB32 TSNG532 VR532 LO532 TA532 EC532
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Adapter sleeve assembly includes one sleeve, one locknut and one lockwasher.
(3)
Labyrinth, taconite seal, end cover, locknut, lockwasher, sold one piece per box.
(4)
Double-lip and V-ring seals sold two pieces per box.

68 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
FOUR-BOLT FSNT HOUSINGS FOR TAPERED BORE BEARINGS

N1

N
J1 A1

J
J2

4 Bolts
Housing Dimensions
Reqd
Housing
Mass

A A1 A2 A3 H H1 H2 J J1 J2 L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg

140 100 158 225 194 100 35 290 50 317 345 18 24 16 13.1
140 100 158 225 194 100 35 290 50 317 345 18 24 16 13.1

145 100 163 220 212 112 35 290 50 317 345 18 24 16 14.0
175 120 191 250 242 125 45 350 70 378 410 18 24 16 22.3
175 120 191 250 242 125 45 350 70 378 410 18 24 16 22.3

160 110 178 235 218 112 40 320 60 348 380 18 24 16 17.6
160 110 178 235 218 112 40 320 60 348 380 18 24 16 17.6
185 120 199 260 271 140 45 350 70 378 410 18 24 16 26.5
185 120 199 260 271 140 45 350 70 378 410 18 24 16 26.5

175 120 191 250 242 125 45 350 70 378 410 18 24 16 22.3
175 120 191 250 242 125 45 350 70 378 410 18 24 16 22.3

185 120 199 260 271 140 45 350 70 378 410 18 24 16 26.5
185 120 199 260 271 140 45 350 70 378 410 18 24 16 26.5

190 130 208 265 290 150 50 380 70 414 445 22 28 20 34.0
190 130 208 265 290 150 50 380 70 414 445 22 28 20 34.0

205 150 223 285 302 150 50 420 80 458 500 26 32 24 39.0
205 150 223 285 302 150 50 420 80 458 500 26 32 24 39.0

220 160 241 295 323 160 60 450 90 486 530 26 32 24 48.0
220 160 241 295 323 160 60 450 90 486 530 26 32 24 48.0

235 160 254 315 344 170 60 470 90 506 550 26 32 24 54.5
235 160 254 315 344 170 60 470 90 506 550 26 32 24 54.5

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 69
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS

TWO-BOLT SNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS


The basic numbers for ordering plummer block housings If ductile iron is desired, add the letter D to the alpha prex
and components are listed in the table below. (e.g., FSNTD 505).
Each housing includes the housing cap, base and cap bolts. Seal sleeve for d shaft to be supplied by customer and a
Assemblies shown are furnished in cast iron. If cast steel is should have same O.D. as d . b
desired, add the letter S to the alpha prex (e.g., FSNTS 518).

Double-Lip Seal V-Ring Seal Labyrinth Seal Taconite Seal

Shaft Dia.
Locating Double-Lip V-Ring Labyrinth Taconite
Housing Bearing End Cover (3)
Rings (1) Seal (2) Seal (2) Seal (3) Seal (3)

da db O.D. x Width
mm mm
SNT 205 22205 SR52X3.5 TSNG205 LO205 TA205 EC506-605
25 30
SNT 206-305 21305 SR62X7.5 TSNG305 VR305 LO305 TA305 EC507-606

SNT 206-305 22206 SR62X6 TSNG206 VR206 LO206 TA206 EC507-606


30 35
SNT 507-606 21306 SR72X7.5 TSNG306 VR306 LO306 TA306 EC507-606

SNT 207 22207 SR72X5.5 TSNG207 VR207 LO207 TA207 EC509


35 45
SNT 208-307 21307 SR80X9 TSNG307 VR307 LO307 TA307 EC510-608

SNT 208-307 22208 SR80X8 TSNG208 VR208 LO208 TA208 EC510-608


40 50 SNT 510-608 21308 SR90X9 TSNG308 VR308 LO308 TA308 EC510-608
SNT 510-608 22308 SR90X4 TSNG308 VR308 LO308 TA308 EC510-608

SNT 209 22209 SR85X3.5 TSNG209 VR209 LO209 TA209 EC511-609


45 55 SNT 511-609 21309 SR100X9.5 TSNG309 VR309 LO309 TA309 EC511-609
SNT 511-609 22309 SR100X4 TSNG309 VR309 LO309 TA309 EC511-609

SNT 210 22210 SR90X9 TSNG210 VR210 LO210 TA210 EC512-610


50 60 SNT 512-610 21310 SR110X10.5 TSNG310 VR310 LO310 TA310 EC512-610
SNT 512-610 22310 SR110X4 TSNG310 VR310 LO310 TA310 EC512-610

SNT 211 22211 SR100X9.5 TSNG211 VR211 LO211 TA211 EC513-611


55 65 SNT 513-611 21311 SR120X11 TSNG311 VR311 LO311 TA311 EC513-611
SNT 513-611 22311 SR120X4 TSNG311 VR311 LO311 TA311 EC513-611

SNT 212 22212 SR110X10 TSNG212 VR212 LO212 TA212 EC515-612


60 70 SNT 515-612 21312 SR130X12.5 TSNG312 VR312 LO312 TA312 EC515-612
SNT 515-612 22312 SR130X5 TSNG312 VR312 LO312 TA312 EC515-612

SNT 213 22213 SR120X10 TSNG213 VR213 LO213 TA213 EC516-613


65 75 SNT 516-613 21313 SR140X12.5 TSNG313 VR313 LO313 TA313 EC516-613
SNT 516-613 22313 SR140X5 TSNG313 VR313 LO313 TA313 EC516-613

SNT 517 22314 SR150X5 TSNG314 VR314 LO314 TA314 EC517


70 80
SNT 517 21314 SR150X13 TSNG314 VR314 LO314 TA314 EC517
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Double-lip and V-ring seals sold two pieces per box. Consult your Timken engineer for double-lip seal availability.
(3)
Labyrinth, taconite seal and end cover, sold one piece per box.

70 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS

2 Bolts
Housing Dimensions
Reqd Housing
Mass

A A1 A2 A3 H H1 H2 J min J J max L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg
67 46 90 140 74 40 19 123 130 137 165 15 20 12 1.5
77 52 89 150 89 50 22 143 150 157 185 15 20 12 2.0

77 52 89 150 89 50 22 143 150 157 185 15 20 12 2.0


82 52 94 140 93 50 22 143 150 157 185 15 20 12 2.2

82 52 96 155 93 50 22 143 150 157 185 15 20 12 2.2


85 60 99 160 108 60 25 165 170 175 205 15 20 12 2.9

85 60 99 160 108 60 25 165 170 175 205 15 20 12 2.9


90 60 102 150 113 60 25 165 170 175 205 15 20 12 3.2
90 60 102 150 113 60 25 165 170 175 205 15 20 12 3.2

85 60 97 160 109 60 25 165 170 175 205 15 20 12 2.9


95 70 107 155 128 70 28 205 210 215 255 18 24 16 4.5
95 70 107 155 128 70 28 205 210 215 255 18 24 16 4.5

90 60 102 165 113 60 25 165 170 175 205 15 20 12 3.2


105 70 117 165 134 70 30 205 210 215 255 18 24 16 5.3
105 70 117 165 134 70 30 205 210 215 255 18 24 16 5.3

95 70 107 170 128 70 28 205 210 215 255 18 24 16 4.5


110 80 122 170 150 80 30 224 230 236 275 18 24 16 6.6
110 80 122 170 150 80 30 224 230 236 275 18 24 16 6.6

105 70 117 180 134 70 30 205 210 215 255 18 24 16 5.2


115 80 127 175 156 80 30 222 230 238 280 18 24 16 6.9
115 80 127 175 156 80 30 222 230 238 280 18 24 16 6.9

110 80 128 190 149 80 30 222 230 238 275 18 24 16 6.6


120 90 138 180 177 95 32 252 260 268 315 22 28 20 9.7
120 90 138 180 177 95 32 252 260 268 315 22 28 20 9.7

125 90 143 210 183 95 32 252 260 268 320 22 28 20 10.4


125 90 143 210 183 95 32 252 260 268 320 22 28 20 10.4

Continued on next page.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 71
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS

TWO-BOLT SNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS continued


The basic numbers for ordering plummer block housings If ductile iron is desired, add the letter D to the alpha prex
and components are listed in the table below. (e.g., FSNTD 505).
Each housing includes the housing cap, base and cap bolts. Seal sleeve for d shaft to be supplied by customer and a
Assemblies shown are furnished in cast iron. If cast steel is should have same O.D. as d . b
desired, add the letter S to the alpha prex (e.g., FSNTS 518).

Double-Lip Seal V-Ring Seal Labyrinth Seal Taconite Seal

Continued from previous page.

Shaft Dia.
Locating Double-Lip V-Ring Labyrinth Taconite
Housing Bearing End Cover (3)
Rings (1) Seal (2) Seal (2) Seal (3) Seal (3)

da db O.D. x Width
mm mm
SNT 215 22215 SR130X12.5 TSNG215 VR215 LO215 TA215 EC518-615
75 85 SNT 518-615 21315 SR160X14 TSNG315 VR315 LO315 TA315 EC518-615
SNT 518-615 22315 SR160X5 TSNG315 VR315 LO315 TA315 EC518-615

SNT 216 22216 SR140X10 TSNG216 VR216 LO216 TA216 EC216


80 90 SNT 519-616 21316 SR170X14.5 TSNG316 VR316 LO316 TA316 EC519-616
SNT 519-616 22316 SR170X5 TSNG316 VR316 LO316 TA316 EC519-616

SNT 217 22217 SR150X12.5 TSNG217 VR217 LO217 TA217 EC217


85 95 SNT 520-617 21317 SR180X14.5 TSNG317 VR317 LO317 TA317 EC520-617
SNT 520-617 22317 SR180X5 TSNG317 VR317 LO317 TA317 EC520-617

SNT 218 22218 SR160X12.5 TSNG218 VR218 LO218 TA218 EC218


90 100
SNT 218 23218 SR160X6.25 TSNG218 VR218 LO218 TA218 EC218

SNT 522-619 21319 SR200X17.5 TSNG319 VR319 LO319 TA319 EC522-619


95 110
SNT 522-619 22319 SR200X6.5 TSNG319 VR319 LO319 TA319 EC522-619

SNT 520-617 22220 SR180X12 TSNG220 VR220 LO220 TA220 EC520-617


SNT 520-617 23220 SR180X4.85 TSNG220 VR220 LO220 TA220 EC520-617
100 115
SNT 524-620 21320 SR215X19.5 TSNG320 VR320 LO320 TA320 EC524-620
SNT 524-620 22320 SR215X6.5 TSNG320 VR320 LO320 TA320 EC524-620

SNT 522-619 22222 SR200X13.5 TSNG222 VR222 LO222 TA222 EC522-619


110 125
SNT 522-619 23222 SR200X5.1 TSNG222 VR222 LO222 TA222 EC522-619

SNT 524-620 22224 SR215X14 TSNG224 VR224 LO224 TA224 EC 524-620


120 135
SNT 524-620 23224 SR215X5 TSNG224 VR224 LO224 TA224 EC 524-620

SNT 526 22226 SR230X13 TSNG226 VR226 LO226 TA226 EC526


130 145
SNT 526 23226 SR230X5 TSNG226 VR226 LO226 TA226 EC526

SNT 528 22228 SR250X15 TSNG228 VR228 LO228 TA228 EC528


140 155
SNT 528 23228 SR250X5 TSNG228 VR228 LO228 TA228 EC528

SNT 530 22230 SR270X16.5 TSNG230 VR230 LO230 TA230 EC530


150 165
SNT 530 23230 SR270X5 TSNG230 VR230 LO230 TA230 EC530

SNT 532 22232 SR290X17 TSNG232 VR232 LO232 TA232 EC532


160 175
SNT 532 23232 SR290X5 TSNG232 VR232 LO232 TA232 EC532
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Double-lip and V-ring seals sold two pieces per box. Consult your Timken engineer for double-lip seal availability.
(3)
Labyrinth, taconite seal and end cover, sold one piece per box.

72 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
TWO-BOLT SNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS

2 Bolts
Housing Dimensions
Reqd Housing
Mass

A A1 A2 A3 H H1 H2 J min J J max L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg
115 80 133 195 155 80 30 222 230 238 280 18 24 16 6.9
140 100 158 225 194 100 35 285 290 295 345 22 28 20 13.1
140 100 158 225 194 100 35 285 290 295 345 22 28 20 13.1

120 90 138 200 177 95 32 252 260 268 315 22 28 20 9.7


145 100 163 220 212 112 35 285 290 295 345 22 28 20 14.0
145 100 163 220 212 112 35 285 290 295 345 22 28 20 14.0

125 90 143 205 183 95 32 252 260 268 320 22 28 20 10.4


160 110 178 235 218 112 40 314 320 326 380 26 32 24 17.6
160 110 178 235 218 112 40 314 320 326 380 26 32 24 17.6

140 100 158 220 194 100 35 285 290 295 345 22 28 20 13.1
140 100 158 220 194 100 35 285 290 295 345 22 28 20 13.1

175 120 191 250 242 125 45 344 350 356 410 26 32 24 22.3
175 120 191 250 242 125 45 344 350 356 410 26 32 24 22.3

160 110 178 235 218 112 40 314 320 326 380 26 32 24 17.6
160 110 178 235 218 112 40 314 320 326 380 26 32 24 17.6
185 120 199 260 271 140 45 344 350 356 410 26 32 24 26.5
185 120 199 260 271 140 45 344 350 356 410 26 32 24 26.5

175 120 191 250 242 125 45 344 350 356 410 26 32 24 22.3
175 120 191 250 242 125 45 344 350 356 410 26 32 24 22.3

185 120 199 260 271 140 45 344 350 356 410 26 32 24 26.5
185 120 199 260 271 140 45 344 350 356 410 26 32 24 26.5

190 130 208 265 290 150 50 373 380 387 445 28 35 24 34.0
190 130 208 265 290 150 50 373 380 387 445 28 35 24 34.0

205 150 223 285 302 150 50 413 420 427 500 35 42 30 39.0
205 150 223 285 302 150 50 413 420 427 500 35 42 30 39.0

220 160 241 295 323 160 60 443 450 457 530 35 42 30 48.0
220 160 241 295 323 160 60 443 450 457 530 35 42 30 48.0

235 160 254 315 344 170 60 463 470 477 550 35 42 30 54.5
235 160 254 315 344 170 60 463 470 477 550 35 42 30 54.5

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 73
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
FOUR-BOLT FSNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS

FOUR-BOLT FSNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS


The basic numbers for ordering plummer block housings If ductile iron is desired, add the letter D to the alpha prex
and components are listed in the table below. (e.g., FSNTD 505).
Each housing includes the housing cap, base and cap bolts. Seal sleeve for d shaft to be supplied by customer and a
Assemblies shown are furnished in cast iron. If cast steel is should have same O.D. as d . b
desired, add the letter S to the alpha prex (e.g., FSNTS 518).

Double-Lip Seal V-Ring Seal Labyrinth Seal Taconite Seal

Shaft Dia.
Locating
Housing Bearing Double-Lip Seal (2) V-Ring Seal (2) Labyrinth Seal (3) Taconite Seal (3) End Cover (3)
Rings (1)

da db O.D. x Width
mm mm
35 45 FSNT 208-307 21307 SR80X9 TSNG307 VR307 LO307 TA307 EC510-608
FSNT 208-307 22208 SR80X8 TSNG208 VR208 LO208 TA208 EC510-608
40 50 FSNT 510-608 21308 SR90X9 TSNG308 VR308 LO308 TA308 EC510-608
FSNT 510-608 22308 SR90X4 TSNG308 VR308 LO308 TA308 EC510-608
FSNT 209 22209 SR85X3.5 TSNG209 VR209 LO209 TA209 EC511-609
45 55 FSNT 511-609 21309 SR100X9.5 TSNG309 VR309 LO309 TA309 EC511-609
FSNT 511-609 22309 SR100X4 TSNG309 VR309 LO309 TA309 EC511-609

FSNT 210 22210 SR90X9 TSNG210 VR210 LO210 TA210 EC512-610


50 60 FSNT 512-610 21310 SR110X10.5 TSNG310 VR310 LO310 TA310 EC512-610
FSNT 512-610 22310 SR110X 4 TSNG310 VR310 LO310 TA310 EC512-610

FSNT 211 22211 SR100X9.5 TSNG211 VR211 LO211 TA211 EC513-611


55 65 FSNT 513-611 21311 SR120X11 TSNG311 VR311 LO311 TA311 EC513-611
FSNT 513-611 22311 SR120X4 TSNG311 VR311 LO311 TA311 EC513-611

FSNT 212 22212 SR110X10 TSNG212 VR212 LO212 TA212 EC515-612


60 70 FSNT 515-612 21312 SR130X12.5 TSNG312 VR312 LO312 TA312 EC515-612
FSNT 515-612 22312 SR130X5 TSNG312 VR312 LO312 TA312 EC515-612

FSNT 213 22213 SR120X10 TSNG213 VR213 LO213 TA213 EC516-613


65 75 FSNT 516-613 21313 SR140X12.5 TSNG313 VR313 LO313 TA313 EC516-613
FSNT 516-613 22313 SR140X5 TSNG313 VR313 LO313 TA313 EC516-613

FSNT 517 22314 SR150X5 TSNG314 VR314 LO314 TA314 EC517


70 80
FSNT 517 21314 SR150X13 TSNG314 VR314 LO314 TA314 EC517

FSNT 215 22215 SR130X12.5 TSNG215 VR215 LO215 TA215 EC518-615


75 85 FSNT 518-615 21315 SR160X14 TSNG315 VR315 LO315 TA315 EC518-615
FSNT 518-615 22315 SR160X5 TSNG315 VR315 LO315 TA315 EC518-615

FSNT 216 22216 SR140X10 TSNG216 VR216 LO216 TA216 EC216


80 90 FSNT 519-616 21316 SR170X14.5 TSNG316 VR316 LO316 TA316 EC519-616
FSNT 519-616 22316 SR170X5 TSNG316 VR316 LO316 TA316 EC519-616
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Double-lip and V-ring seal sold two pieces per box. Consult with your Timken engineer for double-lip seal availability.
(3)
Labyrinth, taconite seal and end cover, sold one piece per box.

74 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
FOUR-BOLT FSNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS

N1

N
J1 A1

J
J2

4 Bolts
Housing Dimensions
Reqd Housing
Mass

A A1 A2 A3 H H1 H2 J J1 J2 L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm kg
85 60 99 160 108 60 25 160 34 205 11 12 2.9
85 60 99 160 108 60 25 160 34 205 11 12 2.9
90 60 102 150 113 60 25 160 34 205 11 12 3.2
90 60 102 150 113 60 25 160 34 205 11 12 3.2
85 60 97 160 109 60 25 160 34 205 11 12 2.9
95 70 107 155 128 70 28 210 35 255 15 20 16 4.5
95 70 107 155 128 70 28 210 35 255 15 20 16 4.5

90 60 102 165 113 60 25 160 34 205 11 12 3.2


105 70 117 165 134 70 30 210 35 255 15 20 16 5.3
105 70 117 165 134 70 30 210 35 255 15 20 16 5.3

95 70 107 170 128 70 28 200 40 255 14 16 4.5


110 80 122 170 150 80 30 230 40 275 15 20 16 6.6
110 80 122 170 150 80 30 230 40 275 15 20 16 6.6

105 70 117 180 134 70 30 200 40 255 14 16 5.2


115 80 127 175 156 80 30 230 40 280 15 20 16 6.9
115 80 127 175 156 80 30 230 40 280 15 20 16 6.9

110 80 128 190 149 80 30 220 48 275 14 16 6.6


120 90 138 180 177 95 32 260 50 315 18 24 20 9.7
120 90 138 180 177 95 32 260 50 315 18 24 20 9.7

125 90 143 210 183 95 32 260 50 320 18 24 20 10.4


125 90 143 210 183 95 32 260 50 320 18 24 20 10.4

115 80 133 195 155 80 30 220 48 280 14 16 6.9


140 100 158 225 194 100 35 290 50 345 18 24 20 13.1
140 100 158 225 194 100 35 290 50 345 18 24 20 13.1

120 90 138 200 177 95 32 252 52 315 18 20 9.7


145 100 163 220 212 112 35 290 50 345 18 24 20 14.0
145 100 163 220 212 112 35 290 50 345 18 24 20 14.0

Continued on next page.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 75
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
FOUR-BOLT FSNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS

FOUR-BOLT FSNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS continued


The basic numbers for ordering plummer block housings If ductile iron is desired, add the letter D to the alpha prex
and components are listed in the table below. (e.g., FSNTD 505).
Each housing includes the housing cap, base and cap bolts. Seal sleeve for d shaft to be supplied by customer and a
Assemblies shown are furnished in cast iron. If cast steel is should have same O.D. as d . b
desired, add the letter S to the alpha prex (e.g., FSNTS 518).

Double-Lip Seal V-Ring Seal Labyrinth Seal Taconite Seal

Continued from previous page.

Shaft Dia.
Locating
Housing Bearing Double-Lip Seal (2) V-Ring Seal (2) Labyrinth Seal (3) Taconite Seal (3) End Cover (3)
Rings (1)

da db O.D. x Width
mm mm
FSNT 217 22217 SR150X12.5 TSNG217 VR217 LO217 TA217 EC217
85 95 FSNT 520-617 21317 SR180X14.5 TSNG317 VR317 LO317 TA317 EC520-617
FSNT 520-617 22317 SR180X5 TSNG317 VR317 LO317 TA317 EC520-617

FSNT 218 22218 SR160X12.5 TSNG218 VR218 LO218 TA218 EC218


90 100
FSNT 218 23218 SR160X6.25 TSNG218 VR218 LO218 TA218 EC218

FSNT 522-619 21319 SR200X17.5 TSNG319 VR219 LO319 TA319 EC522-619


95 110
FSNT 522-619 22319 SR200X6.5 TSNG319 VR219 LO319 TA319 EC522-619

FSNT 520-617 22220 SR180X12 TSNG220 VR220 LO220 TA220 EC520-617


FSNT 520-617 23220 SR180X4.85 TSNG220 VR220 LO220 TA220 EC520-617
100 115
FSNT 524-620 21320 SR215X19.5 TSNG320 VR320 LO320 TA320 EC524-620
FSNT 524-620 22320 SR215X6.5 TSNG320 VR320 LO320 TA320 EC524-620

FSNT 522-619 22222 SR200X13.5 TSNG222 VR222 LO222 TA222 EC522-619


110 125
FSNT 522-619 23222 SR200X5.1 TSNG222 VR222 LO222 TA222 EC522-619

FSNT 524-620 22224 SR215X14 TSNG224 VR224 LO224 TA224 EC 524-620


120 135
FSNT 524-620 23224 SR215X5 TSNG224 VR224 LO224 TA224 EC 524-620

FSNT 526 22226 SR230X13 TSNG226 VR226 LO226 TA226 EC526


130 145
FSNT 526 23226 SR230X5 TSNG226 VR226 LO226 TA226 EC526

FSNT 528 22228 SR250X15 TSNG228 VR228 LO228 TA228 EC528


140 155
FSNT 528 23228 SR250X5 TSNG228 VR228 LO228 TA228 EC528

FSNT 530 22230 SR270X16.5 TSNG230 VR230 LO230 TA230 EC530


150 165
FSNT 530 23230 SR270X5 TSNG230 VR230 LO230 TA230 EC530

FSNT 532 22232 SR290X17 TSNG232 VR232 LO232 TA232 EC532


160 175
FSNT 532 23232 SR290X5 TSNG232 VR232 LO232 TA232 EC532
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Double-lip and V-ring seal sold two pieces per box. Consult with your Timken engineer for double-lip seal availability.
(3)
Labyrinth, taconite seal and end cover, sold one piece per box.

76 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
FOUR-BOLT FSNT HOUSINGS FOR CYLINDRICAL BORE BEARINGS

N1

N
J1 A1

J
J2

4 Bolts
Housing Dimensions
Reqd Housing
Mass

A A1 A2 A3 H H1 H2 J J1 J2 L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm kg
125 90 143 205 183 95 32 252 52 320 18 20 10.4
160 110 178 235 218 112 40 320 60 380 18 24 24 17.6
160 110 178 235 218 112 40 320 60 380 18 24 24 17.6

140 100 158 220 194 100 35 280 58 345 18 20 13.1


140 100 158 220 194 100 35 280 58 345 18 20 13.1

175 120 191 250 242 125 45 350 70 410 18 24 24 22.3


175 120 191 250 242 125 45 350 70 410 18 24 24 22.3

160 110 178 235 218 112 40 320 60 380 18 24 24 17.6


160 110 178 235 218 112 40 320 60 380 18 24 24 17.6
185 120 199 260 271 140 45 350 70 410 18 24 24 26.5
185 120 199 260 271 140 45 350 70 410 18 24 24 26.5

175 120 191 250 242 125 45 350 70 410 18 24 24 22.3


175 120 191 250 242 125 45 350 70 410 18 24 24 22.3

185 120 199 260 271 140 45 350 70 410 18 24 24 26.5


185 120 199 260 271 140 45 350 70 410 18 24 24 26.5

190 130 208 265 290 150 50 380 70 445 22 28 24 34.0


190 130 208 265 290 150 50 380 70 445 22 28 24 34.0

205 150 223 285 302 150 50 420 80 500 26 32 30 39.0


205 150 223 285 302 150 50 420 80 500 26 32 30 39.0

220 160 241 295 323 160 60 450 90 530 26 32 30 48.0


220 160 241 295 323 160 60 450 90 530 26 32 30 48.0

235 160 254 315 344 170 60 470 90 550 26 32 30 54.5


235 160 254 315 344 170 60 470 90 550 26 32 30 54.5

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 77
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
LARGE PLUMMER BLOCK HOUSINGS 3000 AND 3100 SERIES

LARGE PLUMMER BLOCK HOUSINGS 3000 AND 3100 SERIES


The basic numbers for ordering plummer block
housings and components are listed in the
table below.
Each housing includes the housing cap, base
and cap bolts.
Housings shown are furnished in cast iron. If
cast steel is desired, add the letter S to the
alpha prex (e.g., SNTS 518). If ductile iron is
desired, add the letter D to the alpha prex
(e.g., SNTD 505).
Housings with the F sufx are manufactured for
xed bearings. Those with the L sufx are oat
position housings.

Labyrinth Seal Taconite Seal

Quantity
(Typically
Shaft Locating Adapter Labyrinth Taconite
Housing Bearing required for this Locknut (3) Lockwasher (3) End Cover (3)
Dia. Rings (1) Sleeve (2) Seal (3) Seal (3)
bearing/housing
conguration)

d O.D. x Width
mm
150 SNT 3134 23134K SR280X10 2 H3134 KM34 MB34 LO34 TA34 EC34
SNT 3036 23036K SR280X17 2 H3036 KM36 MB36 LO36 TA36 EC36
160
SNT 3136 23136K SR300X10 2 H3136 KM36 MB36 LO36 TA36 EC36
SNT 3038 23038K SR290X10 4 H3038 KML38 MBL38 LO38 TA38 EC38
170
SNT 3138 23138K SR320X10 2 H3138 KM38 MB38 LO38 TA38 EC38
SNT 3040 23040K SR310X10 4 H3040 KM40 MB40 LO40 TA40 EC40
180
SNT 3140 23140K SR340X10 2 H3140 KM40 MB40 LO40 TA40 EC40
SNT 3044 23044K SR340X10 4 OH3044H HM3044 MS3044 LO44 TA44 EC44
200
SNT 3144 23144K SR370X10 2 OH3144H HM44T MB44 LO44 TA44 EC44
SNT 3048 23048K SR360X12 4 OH3048H HM3048 MS3048 LO48 TA48 EC48
220
SNT 3148 23148K SR400X10 2 OH3148H HM48T MB48 LO48 TA48 EC48
SNT 3052 23052K SR400X22 2 OH3052H HM3052 MS3052 LO52 TA52 EC52
240
SNT 3152 23152K SR440X10 2 OH3152H HM52T MB52 LO52 TA52 EC52
SNT 3056 23056K SR420X10 6 OH3056H HM3056 MS3056 LO56 TA56 EC56
260
SNT 3156 23156K SR460X10 2 OH3156H HM56T MB56 LO56 TA56 EC56
SNT 3060 23060K SR460X25 2 OH3060H HM3060 MS3060 LO60 TA60 EC60
280
SNT 3160 23160K SR500X10 2 OH3160H HM3160 MS3160 LO60 TA60 EC60
SNT 3064 23064K SR480X10 6 OH3064H HM3064 MS3064 LO64 TA64 EC64
300
SNT 3164 23164K SR540X10 2 OH3164H HM3164 MS3164 LO64 TA64 EC64
SNT 3068 23068K SR520X16 4 OH3068H HM3068 MS3068 LO68 TA68 EC68
320 SNT 3168F 23168K FIXED HOUSING OH3168H HM3168 MS3168 LO68 TA68 EC68
SNT 3168L 23168K FLOAT HOUSING OH3168H HM3168 MS3168 LO68 TA68 EC68
SNT 3072 23172K SR540X16 4 OH3072H HM3072 MS3072 LO72 TA72 EC72
340 SNT 3172F 23172K FIXED HOUSING OH3172H HM3172 MS3172 LO72 TA72 EC72
SNT 3172L 23172K FLOAT HOUSING OH3172H HM3172 MS3172 LO72 TA72 EC72
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Adapter sleeve assembly includes one sleeve, one locknut and one lockwasher.
(3)
Labyrinth, taconite seal, end cover, locknut, lockwasher, sold one piece per box.

78 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
LARGE PLUMMER BLOCK HOUSINGS 3000 AND 3100 SERIES

4 Bolts
Housing Dimensions
Reqd
Housing
Mass

A A1 A2 A3 C H H1 H2 J J1 L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg
230 180 240 300 14 333 170 70 430 100 510 28 34 24 75
230 180 240 310 14 333 170 70 430 100 510 28 34 24 72
240 190 250 315 15 353 180 75 450 110 530 28 34 24 92
240 190 250 315 15 353 180 75 450 110 530 28 34 24 81
260 210 270 335 10 375 190 80 480 120 560 28 34 24 112
260 210 270 335 10 375 190 80 480 120 560 28 34 24 110
280 230 290 355 10 411 210 85 510 130 610 35 42 30 130
280 230 290 355 10 411 210 85 510 130 610 35 42 30 118
290 240 300 365 12 434 220 90 540 140 640 35 42 30 140
290 240 300 385 12 434 220 90 540 140 640 35 42 30 138
310 260 315 400 12 474 240 95 600 150 700 35 42 30 193
310 260 315 400 12 474 240 95 600 150 700 35 42 30 189
320 280 330 415 13 516 260 100 650 160 770 42 50 36 235
320 280 330 415 13 516 260 100 650 160 770 42 50 36 254
320 280 330 415 16 551 280 105 670 160 790 42 50 36 260
320 280 330 415 16 551 280 105 670 160 790 42 50 36 260
350 310 360 445 22 591 300 110 710 190 830 42 50 36 310
350 310 360 445 22 591 300 110 710 190 830 42 50 36 300
370 330 380 462 23 631 320 115 750 200 880 42 50 36 346
370 330 380 465 23 631 320 115 750 200 880 42 50 36 339
400 360 410 492 24 675 340 120 810 220 950 42 50 36 432.5
400 360 410 492 24 675 340 120 810 220 950 42 50 36 429.5
370 330 380 465 23 631 320 115 750 200 950 42 50 36 342
400 360 410 492 30 695 350 120 840 220 1000 42 50 36 458
400 360 410 492 30 695 350 120 840 220 1000 42 50 36 454

Continued on next page.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 79
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
LARGE PLUMMER BLOCK HOUSINGS 3000 AND 3100 SERIES

LARGE PLUMMER BLOCK HOUSINGS 3000 AND 3100 SERIES continued


The basic numbers for ordering plummer block
housings and components are listed in the
table below.
Each housing includes the housing cap, base
and cap bolts.
Housings shown are furnished in cast iron. If
cast steel is desired, add the letter S to the
alpha prex (e.g., SNTS 518). If ductile iron is
desired, add the letter D to the alpha prex
(e.g., SNTD 505).
Housings with the F sufx are manufactured for
xed bearings. Those with the L sufx are oat
position housings.

Continued from previous page.

Quantity
(Typically
Shaft Locating Adapter Labyrinth Taconite
Housing Bearing required for this Locknut (3) Lockwasher (3) End Cover (3)
Dia. Rings (1) Sleeve (2) Seal (3) Seal (3)
bearing/housing
conguration)

d O.D. x Width
mm
SNT 3076F 23076K FIXED HOUSING OH3076H HM3076 MS3076 LO76 TA76 EC76
SNT 3076L 23076K FLOAT HOUSING OH3076H HM3076 MS3076 LO76 TA76 EC76
360
SNT 3176F 23176K FIXED HOUSING OH3176H HM3176 MS3176 LO76 TA76 EC76
SNT 3176L 23176K FLOAT HOUSING OH3176H HM3176 MS3176 LO76 TA76 EC76
SNT 3080F 23080K FIXED HOUSING OH3080H HM3080 MS3080 LO80 TA80 EC80
SNT 3080L 23080K FLOAT HOUSING OH3080H HM3080 MS3080 LO80 TA80 EC80
380
SNT 3180F 23180K FIXED HOUSING OH3180H HM3180 MS3180 LO80 TA80 EC80
SNT 3180L 23180K FLOAT HOUSING OH3180H HM3180 MS3180 LO80 TA80 EC80
SNT 3084F 23084K FIXED HOUSING OH3084H HM3084 MS3084 LO84 TA84 EC84
400
SNT 3084L 23084K FLOAT HOUSING OH3084H HM3084 MS3084 LO84 TA84 EC84
(1)
Locating rings = minimum two required for xed position, sold one piece per box.
(2)
Adapter sleeve assembly includes one sleeve, one locknut and one lockwasher.
(3)
Labyrinth, taconite seal, end cover, locknut, lockwasher, sold one piece per box.

80 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
LARGE PLUMMER BLOCK HOUSINGS 3000 AND 3100 SERIES

4 Bolts
Housing Dimensions
Reqd
Housing
Mass

A A1 A2 A3 C H H1 H2 J J1 L N N1 G
mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg
400 360 410 495 24 675 340 120 810 220 1000 42 50 36 430
400 360 410 495 24 675 340 120 810 220 1000 42 50 36 427
400 360 410 492 30 715 360 120 870 220 1040 42 50 36 487
400 360 410 492 30 715 360 120 870 220 1040 42 50 36 484
400 360 410 495 30 695 350 120 840 220 1040 42 50 36 454
400 360 410 495 30 695 350 120 840 220 1040 42 50 36 450
430 390 440 522 30 775 380 125 950 240 1120 48 60 42 595
430 390 440 522 30 775 380 125 950 240 1120 48 60 42 595
400 360 410 495 30 715 360 120 870 220 1120 42 50 36 483
400 360 410 495 30 715 360 120 870 220 1120 42 50 36 480

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 81
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
METRIC SHAFT DIAMETERS

METRIC SHAFT DIAMETERS


TABLE 20. SUGGESTED METRIC SHAFT DIAMETERS FOR USE WITH ADAPTER SLEEVES (MM)
Shaft O.D. Max. Min. Shaft O.D. Max. Min.

20 20.000 19.925 190 190.000 189.875

25 25.000 24.925 200 200.000 199.875

30 30.000 29.925 210 210.000 209.850

35 35.000 34.925 220 220.000 219.850

40 40.000 39.925 230 230.000 229.850

45 45.000 44.925 240 240.000 239.850

50 50.000 49.925 250 250.000 249.850

55 55.000 54.900 260 260.000 259.850

60 60.000 59.900 270 270.000 269.825

65 65.000 64.900 280 280.000 279.825

70 70.000 69.900 290 290.000 289.825

75 75.000 74.900 300 300.000 299.825

80 80.000 79.900 310 310.000 309.825

85 85.000 84.900 320 320.000 319.800

90 90.000 89.900 330 330.000 329.800

95 95.000 94.900 340 340.000 339.800

100 100.000 99.900 350 350.000 349.800

105 105.000 104.875 360 360.000 359.800

110 110.000 109.875 370 370.000 369.800

115 115.000 114.875 380 380.000 379.800

120 120.000 119.875 390 390.000 389.800

125 125.000 124.875 400 400.000 399.800

130 130.000 129.875 410 410.000 409.800

135 135.000 134.875 420 420.000 419.800

140 140.000 139.875 430 430.000 429.800

145 145.000 144.875 440 440.000 439.800

150 150.000 149.875 450 450.000 449.800

160 160.000 159.875 460 460.000 459.800

170 170.000 169.875 470 470.000 469.800

180 180.000 179.875 480 480.000 479.800

82 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
SPHERICAL ROLLER BEARING PRODUCT DATA TABLES

SPHERICAL ROLLER BEARING


PRODUCT DATA TABLES
Timken spherical roller bearings feature all of the
characteristics that have made Timken renowned superior
design, reliable performance and comprehensive technical
support. Spherical roller bearings are designed to manage
high radial loads and perform consistently, even when
misalignment, marginal lubrication, contamination,
extreme speeds and critical application stresses are
present.

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Spherical Roller Bearing Product Data Tables . . . . . . . . . . . .85

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 83
SNT SPLIT PLUMMER BLOCKS
SPHERICAL ROLLER BEARING PRODUCT DATA TABLES NOMENCLATURE

SPHERICAL ROLLER BEARING NOMENCLATURE

Series: Bore code:


(5 x _ _ = bore in
millimeters
when 2 digits)
5 x 07 = 35 mm
239 230 240 231 241 222 232 213 223 233 5 x 76 = 380 mm
(/ # # # = bore in
millimeters
when >2 digits)
/530 = 530 mm
/1060 = 1060 mm

222 17 K EJ W33 C3

223 26 EM W33 W800 C4

Common modication and style codes: Radial Internal Clearances (RIC):


K = tapered bore C2 < C0
Note:
EJ = two-piece steel cage - window type(1) C0 = normal
EJ bearings supersede
EM/YM = one-piece brass cage - nger type, roller piloted C3 > C0
CJ and VCSJ bearings.
EMB/YMB = one-piece brass, nger type, land piloted C4 > C3
EM bearings supersede W33 = three holes and groove in O.D. C5 > C4
YM bearings. W800 = shaker screen modication: C6 = special clearance
EMB bearings supersede - tighter bore diameter and O.D. tolerances
YMB bearings. - brass cage
- RIC in upper 23 of clearance specied
(1)
See complete modication code list on page 61 of the
Timken Spherical Roller Bearing Catalog (order no. 10446),
found on www.timken.com.

Fig. 35. Timken spherical roller bearing nomenclature.

84 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
SPHERICAL ROLLER BEARING PRODUCT DATA TABLES 213 SERIES (200, 300, 500, 600 SERIES SNT, FSNT)

213 SERIES B R B R B R
(200, 300, 500, 600 SERIES SNT, FSNT)
Bearings are available with a tapered bore for adapter-type R R R
mounting. To order, add the sufx K to bearing number
(e.g., 23120K). Dd da Da D d da Da D d da Da
Consult your Timken engineer and www.timken.com for
up-to-date information about the availability of the bearings
you have selected.
This section lists spherical roller bearings pertinent to
Timken SNT plummer blocks. For a wider selection, consult
www.timken.com or the Timken Spherical Roller Bearing EJ EM/YM EMB/YMB
catalog (order no. 10446).

Equivalent Radial Load


Mounting Data Factors(2) Thermal
Bearing Dimensions Load Ratings Dynamic Static Geometry Speed
Bearing
Cage Fa Fa Factor(3) Ratings(4)
Part __ e __ >e In Wt.
Type Fillet(1) Backing Dia.
No. Fr Fr All
(Max.)
Bore O.D. Width Dynamic Static Shaft Housing X=1 X = 0.67 Cases
Oil Grease
d D B C Co R da Da e Y Y Y0 Cg
mm mm mm kN kN mm mm mm kg
RPM RPM
in. in. in. lbf. lbf. in. in. in. lbs.
25 62 17 55.5 44.3 1 35 55 0.3
21305 EJ 0.27 2.48 3.7 2.43 0.037 10000 8100
0.9843 2.4409 0.6693 12500 9970 0.04 1.4 2.1 0.7
30 72 19 70.3 56.5 1 41 64 0.4
21306 EJ 0.26 2.6 3.87 2.54 0.041 8900 7200
1.1811 2.8346 0.748 15800 12700 0.04 1.6 2.5 0.9
35 80 21 90.2 77.8 1.5 47 71 0.5
21307 EJ 0.26 2.56 3.81 2.5 0.044 7900 6400
1.378 3.1496 0.8268 20300 17500 0.06 1.9 2.8 1.1
40 90 23 113 102 1.5 54 80 0.7
21308 EJ 0.26 2.64 3.93 2.58 0.048 7100 5800
1.5748 3.5433 0.9055 25400 22900 0.06 2.1 3.2 1.5
45 100 25 138 125 1.5 60 90 1.0
21309 EJ 0.25 2.75 4.09 2.69 0.052 6500 5300
1.7717 3.937 0.9843 31000 28200 0.06 2.4 3.5 2.2
50 110 27 163 151 2 67 99 1.2
21310 EJ 0.24 2.83 4.21 2.76 0.055 5900 4900
1.9685 4.3307 1.063 36700 33800 0.08 2.6 3.9 2.6
55 120 29 188 176 2 73 108 1.6
21311 EJ 0.24 2.81 4.18 2.75 0.058 5500 4500
2.1654 4.7244 1.1417 42400 39500 0.08 2.9 4.2 3.5
60 130 31 225 219 2 80 116 2.0
21312 EJ 0.23 2.91 4.33 2.84 0.062 5100 4200
2.3622 5.1181 1.2205 50500 49200 0.08 3.2 4.6 4.4
65 140 33 259 254 2 86 126 2.4
21313 EJ 0.23 2.94 4.37 2.87 0.065 4800 3900
2.5591 5.5118 1.2992 58200 57100 0.08 3.4 5 5.3
70 150 35 292 289 2 93 135 3.0
21314 EJ 0.23 2.97 4.42 2.9 0.068 4500 3700
2.7559 5.9055 1.378 65600 65000 0.08 3.7 5.3 6.6
75 160 37 322 321 2 99 144 3.5
21315 EJ 0.23 2.98 4.43 2.91 0.071 4300 3600
2.9528 6.2992 1.4567 72400 72200 0.08 3.9 5.7 7.7
80 170 39 363 363 2 105 153 4.2
21316 EJ 0.22 3.01 4.47 2.94 0.073 4100 3400
3.1496 6.6929 1.5354 81700 81700 0.08 4.1 6 9.2
85 180 41 403 407 2.5 112 162 4.9
21317 EJ 0.22 3.04 4.53 2.97 0.076 3900 3200
3.3465 7.0866 1.6142 90600 91500 0.1 4.4 6.4 10.8
90 190 43 442 449 2.5 118 171 5.8
21318 EJ 0.22 3.05 4.55 2.99 0.079 3700 3100
3.5433 7.4803 1.6929 99400 101000 0.1 4.7 6.7 12.8
(1)
Maximum shaft or housing llet radius that bearing corners will clear.
(2)
These factors apply for both inch and metric calculations. See engineering section for instructions on use.
(3)
Geometry constant for Lubrication Life Factor a31 is found in the Bearing Ratings section of the Engineering Manual (order no. 10424).
(4)
See thermal speed ratings in the Engineering Manual (order no. 10424).
NOTE: Where EJ and EM/EMB have different load ratings, the more conservative one was taken to use for both assemblies.
NOTE: Tolerance and shaft diameters are shown in tables 2 and 3 on pages 19 and 20 as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 85
SNT SPLIT PLUMMER BLOCKS
SPHERICAL ROLLER BEARING PRODUCT DATA TABLES 222 SERIES (200, 500 SERIES SNT, FSNT)

222 SERIES B R B R B R
(200, 500 SERIES SNT, FSNT)
Bearings are available with a tapered bore for adapter-type R R R
mounting. To order, add the sufx K to bearing number
(e.g., 23120K). Dd da Da D d da Da D d da Da
Consult your Timken engineer and www.timken.com for
up-to-date information about the availability of the bearings
you have selected.
This section lists spherical roller bearings pertinent to
Timken SNT plummer blocks. For a wider selection, consult
www.timken.com or the Timken Spherical Roller Bearing EJ EM/YM EMB/YMB
catalog (order no. 10446).

Equivalent Radial Load


Mounting Data Factors(2) Thermal
Bearing Dimensions Load Ratings Dynamic Static Geometry Speed
Bearing
Cage Fa Fa Factor(3) Ratings(4)
Part __ e __ >e In Wt.
Type Fillet(1) Backing Dia.
No. Fr Fr All
(Max.)
Bore O.D. Width Dynamic Static Shaft Housing X=1 X = 0.67 Cases
Oil Grease
d D B C Co R da Da e Y Y Y0 Cg
mm mm mm kN kN mm mm mm kg
RPM RPM
in. in. in. lbf. lbf. in. in. in. lbs.
25 52 18 50.6 43.1 1 30 47 0.2
22205 EJ 0.34 2 2.98 1.96 0.032 12000 9200
0.9843 2.0472 0.7087 11400 9690 0.04 1.2 1.9 0.4
30 62 20 67.4 60.8 1 38 56 0.3
22206 EJ 0.31 2.15 3.2 2.1 0.037 9700 7800
1.1811 2.4409 0.7874 15200 13700 0.04 1.5 2.2 0.7
35 72 23 90.5 88 1 45 65 0.5
22207 EJ 0.31 2.21 3.29 2.16 0.041 8600 6900
1.378 2.8346 0.9055 20300 19700 0.04 1.8 2.6 1.1
40 80 23 104 99.7 1 50 73 0.6
22208 EJ / EM 0.27 2.47 3.67 2.41 0.044 7500 6000
1.5748 3.1496 0.9055 23400 22400 0.04 2 2.9 1.3
45 85 23 104 101 1 55 77 0.6
22209 EJ / EM 0.26 2.64 3.93 2.58 0.046 6800 5500
1.7717 3.3465 0.9055 23500 22800 0.04 2.2 3 1.3
50 90 23 112 112 1 59 82 0.6
22210 EJ / EM 0.24 2.84 4.23 2.78 0.049 6200 5000
1.9685 3.5433 0.9055 25200 25100 0.04 2.3 3.2 1.3
55 100 25 134 134 1.5 66 91 0.9
22211 EJ / EM 0.23 2.95 4.4 2.89 0.052 5800 4700
2.1654 3.937 0.9843 30100 30100 0.06 2.6 3.6 2.0
60 110 28 163 164 1.5 72 100 1.2
22212 EJ / EM 0.24 2.84 4.23 2.78 0.055 5500 4400
2.3622 4.3307 1.1024 36600 36900 0.06 2.8 4 2.6
65 120 31 198 204 1.5 78 109 1.6
22213 EJ / EM 0.24 2.79 4.15 2.73 0.058 5100 4200
2.5591 4.7244 1.2205 44600 45900 0.06 3.1 4.3 3.5
70 125 31 205 219 1.5 84 114 1.6
22214 EJ / EM 0.23 2.9 4.32 2.84 0.063 4800 3900
2.7559 4.9213 1.2205 46000 49200 0.06 3.3 4.5 3.5
75 130 31 222 240 1.5 88 120 1.7
22215 EJ 0.22 3.14 4.67 3.07 0.062 4600 3700
2.9528 5.1181 1.2205 49900 54100 0.06 3.5 4.7 3.7
80 140 33 254 278 2 95 129 2.2
22216 EJ / EM 0.22 3.14 4.67 3.07 0.065 4300 3500
3.1496 5.5118 1.2992 57200 62500 0.08 3.7 5.1 4.8
(1)
Maximum shaft or housing llet radius that bearing corners will clear.
(2)
These factors apply for both inch and metric calculations. See Timken Engineering Manual (order no. 10424) for instructions on use. Continued on next page.
(3)
Geometry constant for Lubrication Life Factor a31 is found in the Bearing Ratings section of the Engineering Manual (order no. 10424).
(4)
See thermal speed ratings in the Engineering Manual (order no. 10424).
NOTE: Where EJ and EM/EMB have different load ratings, the more conservative one was taken to use for both assemblies.
NOTE: Tolerance and shaft diameters are shown in tables 2 and 3 on pages 19 and 20 as variances from nominal bearing bore.

86 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
SPHERICAL ROLLER BEARING PRODUCT DATA TABLES 222 SERIES (200, 500 SERIES SNT, FSNT)

B R B R B R

R R R

Dd da Da D d da Da D d da Da

EJ EM/YM EMB/YMB

Continued from previous page.

Equivalent Radial Load


Mounting Data Factors(2) Thermal
Bearing Dimensions Load Ratings Dynamic Static Geometry Speed
Bearing
Cage Fa Fa Factor(3) Ratings(4)
Part __ e __ >e In Wt.
Type Fillet(1) Backing Dia.
No. Fr Fr All
(Max.)
Bore O.D. Width Dynamic Static Shaft Housing X=1 X = 0.67 Cases
Oil Grease
d D B C Co R da Da e Y Y Y0 Cg
mm mm mm kN kN mm mm mm kg
RPM RPM
in. in. in. lbf. lbf. in. in. in. lbs.
85 150 36 286 302 2 101 139 2.7
22217 EJ / EM 0.22 3.07 4.57 3 0.068 4200 3400
3.3465 5.9055 1.4173 64200 67900 0.08 4 5.5 5.9
90 160 40 355 388 2 105 146 3.5
22218 EJ / EM 0.23 2.9 4.31 2.83 0.07 4000 3300
3.5433 6.2992 1.5748 79700 87200 0.08 4.2 5.8 7.7
95 170 43 385 441 2 114 155 4.2
22219 EJ / EM 0.23 2.88 4.29 2.82 0.076 3900 3200
3.7402 6.6929 1.6929 86600 99000 0.08 4.5 6.1 9.2
100 180 46 435 502 2 120 163 5.0
22220 EJ / EM 0.24 2.85 4.24 2.78 0.079 3800 3100
3.937 7.0866 1.811 97700 113000 0.08 4.7 6.4 11.0
110 200 53 555 653 2 133 182 7.2
22222 EJ / EM 0.25 2.73 4.06 2.67 0.084 3500 2900
4.3307 7.874 2.0866 125000 147000 0.08 5.2 7.2 15.8
120 215 58 647 772 2 143 196 9.0
22224 EJ / EM 0.25 2.7 4.02 2.64 0.081 3200 2600
4.7244 8.4646 2.2835 145000 174000 0.08 5.6 7.7 19.8
130 230 64 757 945 2.5 155 210 11.3
22226 EJ / EM 0.26 2.62 3.9 2.56 0.079 2900 2400
5.1181 9.0551 2.5197 170000 212000 0.1 6.1 8.3 24.9
140 250 68 863 1060 2.5 167 228 14.2
22228 EJ / EM 0.25 2.67 3.98 2.61 0.082 2600 2200
5.5118 9.8425 2.6772 194000 237000 0.1 6.6 9 31.2
150 270 73 1000 1230 2.5 179 246 17.8
22230 EJ / EM 0.25 2.69 4 2.63 0.087 2400 2000
5.9055 10.6299 2.874 225000 276000 0.1 7 9.7 39.2
160 290 80 1170 1450 2.5 192 264 23.0
22232 EJ / EM 0.26 2.62 3.91 2.57 0.09 2200 1800
6.2992 11.4173 3.1496 263000 326000 0.1 7.5 10.4 50.6
(1)
Maximum shaft or housing llet radius that bearing corners will clear.
(2)
These factors apply for both inch and metric calculations. See engineering section for instructions on use.
(3)
Geometry constant for Lubrication Life Factor a31 is found in the Bearing Ratings section of the Engineering Manual (order no. 10424).
(4)
See thermal speed ratings in the Engineering Manual (order no. 10424).
NOTE: Where EJ and EM/EMB have different load ratings, the more conservative one was taken to use for both assemblies.
NOTE: Tolerance and shaft diameters are shown in tables 2 and 3 on pages 19 and 20 as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 87
SNT SPLIT PLUMMER BLOCKS
SPHERICAL ROLLER BEARING PRODUCT DATA TABLES 223 SERIES (500, 600 SERIES SNT, FSNT)

223 SERIES B R B R B R
(500, 600 SERIES SNT, FSNT)
Bearings are available with a tapered bore for adapter-type R R R
mounting. To order, add the sufx K to bearing number
(e.g., 23120K). Dd da Da D d da Da D d da Da
Consult your Timken engineer and www.timken.com for
up-to-date information about the availability of the bearings
you have selected.
This section lists spherical roller bearings pertinent to
Timken SNT plummer blocks. For a wider selection, consult
www.timken.com or the Timken Spherical Roller Bearing EJ EM/YM EMB/YMB
catalog (order no. 10446).

Equivalent Radial Load


Mounting Data Factors(2)
Thermal
Bearing Dimensions Load Ratings Dynamic Static Geometry
Bearing Speed Ratings(4)
Cage Fa Fa Factor(3)
Part __ e __ >e In Wt.
Type Fillet(1) Backing Dia.
No. Fr Fr All
(Max.)
Bore O.D. Width Dynamic Static Shaft Housing X=1 X = 0.67 Cases
Oil Grease
d D B C Co R da Da e Y Y Y0 Cg
mm mm mm kN kN mm mm mm kg
RPM RPM
in. in. in. lbf. lbf. in. in. in. lbs.
40 90 33 155 147 1.5 53 81 1.0
22308 EJ / EM 0.36 1.87 2.79 1.83 0.046 6700 5600
1.5748 3.5433 1.2992 34900 33100 0.06 2.1 3.2 2.2
45 100 36 190 182 1.5 58 90 1.3
22309 EJ / EM 0.36 1.9 2.83 1.86 0.049 6100 5100
1.7717 3.937 1.4173 42700 40800 0.06 2.3 3.5 2.9
50 110 40 238 241 2 65 98 1.9
22310 EJ / EM 0.36 1.89 2.81 1.85 0.055 5500 4600
1.9685 4.3307 1.5748 53500 54200 0.08 2.6 3.9 4.2
55 120 43 279 284 2 69 106 2.4
22311 EJ / EM 0.36 1.89 2.81 1.84 0.057 5100 4300
2.1654 4.7244 1.6929 62800 63800 0.08 2.7 4.2 5.3
60 130 46 321 329 2 77 117 3.0
22312 EJ / EM 0.34 1.98 2.94 1.93 0.061 4700 4000
2.3622 5.1181 1.811 72200 73900 0.08 3 4.6 6.6
65 140 48 361 371 2 84 127 3.6
22313 EJ / EM 0.33 2.05 3.05 2 0.064 4400 3800
2.5591 5.5118 1.8898 81300 83300 0.08 3.3 5 7.9
70 150 51 395 414 2 91 135 4.4
22314 EJ / EM 0.33 2.07 3.08 2.02 0.067 4200 3600
2.7559 5.9055 2.0079 88800 93100 0.08 3.6 5.3 9.7
75 160 55 450 478 2 97 144 5.4
22315 EJ / EM 0.33 2.04 3.04 2 0.071 3900 3300
2.9528 6.2992 2.1654 101000 107000 0.08 3.8 5.7 11.9
80 170 58 499 534 2 103 153 6.4
22316 EJ / EM 0.33 2.06 3.06 2.01 0.073 3700 3200
3.1496 6.6929 2.2835 112000 120000 0.08 4.1 6 14.1
85 180 60 569 623 2.5 110 162 7.5
22317 EJ / EM 0.32 2.11 3.14 2.06 0.076 3500 3000
3.3465 7.0866 2.3622 128000 140000 0.1 4.3 6.4 16.5
90 190 64 634 703 2.5 116 171 8.8
22318 EJ / EM 0.32 2.09 3.11 2.04 0.079 3300 2800
3.5433 7.4803 2.5197 143000 158000 0.1 4.6 6.7 19.4
95 200 67 694 774 2.5 122 180 10.2
22319 EJ / EM 0.32 2.1 3.13 2.05 0.082 3000 2600
3.7402 7.874 2.6378 156000 174000 0.1 4.8 7.1 22.4
100 215 73 779 856 2.5 130 193 12.8
22320 EJ / EM 0.33 2.06 3.07 2.02 0.072 2800 2400
3.937 8.4646 2.874 175000 193000 0.1 5.1 7.6 28.2
(1)
Maximum shaft or housing llet radius that bearing corners will clear.
(2)
These factors apply for both inch and metric calculations. See engineering section for instructions on use.
(3)
Geometry constant for Lubrication Life Factor a31 is found in the Bearing Ratings section of the Engineering Manual (order no. 10424).
(4)
See thermal speed ratings in the Engineering Manual (order no. 10424).
NOTE: Where EJ and EM/EMB have different load ratings, the more conservative one was taken to use for both assemblies.
NOTE: Tolerance and shaft diameters are shown in tables 2 and 3 on pages 19 and 20 as variances from nominal bearing bore.

88 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
SPHERICAL ROLLER BEARING PRODUCT DATA TABLES 230 SERIES (3000 SERIES SNT, FSNT)

230 SERIES B R B R B R
(3000 SERIES SNT, FSNT)
Bearings are available with a tapered bore for adapter-type R R R
mounting. To order, add the sufx K to bearing number
(e.g., 23120K). Dd da Da D d da Da D d da Da
Consult your Timken engineer and www.timken.com for
up-to-date information about the availability of the bearings
you have selected.
This section lists spherical roller bearings pertinent to
Timken SNT plummer blocks. For a wider selection, consult
www.timken.com or the Timken Spherical Roller Bearing EJ EM/YM EMB/YMB
catalog (order no. 10446).

Equivalent Radial Load


Mounting Data Factors(2) Thermal
Bearing Dimensions Load Ratings Dynamic Static Geometry Speed
Bearing
Cage Fa F__ Factor(3) Ratings(4)
Part __ e a
>e In Wt.
Type Fillet(1) Backing Dia.
No. Fr Fr All
(Max.)
Bore O.D. Width Dynamic Static Shaft Housing X=1 X = 0.67 Cases
Oil Grease
d D B C Co R da Da e Y Y Y0 Cg
mm mm mm kN kN mm mm mm kg
RPM RPM
in. in. in. lbf. lbf. in. in. in. lbs.
180 280 74 1020 1480 2 204 260 16.8
23036 EJ / EM 0.23 2.91 4.34 2.85 0.093 2000 1700
7.0866 11.0236 2.9134 229000 332000 0.08 8 10.2 37.0
190 290 75 1060 1580 2 214 270 17.8
23038 EJ / EM 0.23 3 4.47 2.93 0.096 1900 1600
7.4803 11.4173 2.9528 239000 355000 0.08 8.4 10.6 39.2
200 310 82 1230 1760 2 225 289 22.6
23040 EJ / EM 0.23 2.95 4.4 2.89 0.095 1800 1500
7.874 12.2047 3.2283 276000 395000 0.08 8.9 11.4 49.7
220 340 90 1340 1970 2.5 247 313 29.8
23044 EJ / EM 0.24 2.77 4.13 2.71 0.105 1700 1400
8.6614 13.3858 3.5433 300000 443000 0.1 9.7 12.3 65.6
240 360 92 1400 2140 2.5 267 334 31.9
23048 EJ / EM 0.23 2.91 4.34 2.85 0.111 1500 1300
9.4488 14.1732 3.622 315000 480000 0.1 10.5 13.1 70.2
260 400 104 1820 2740 3 291 369 47.6
23052 EJ / EMB 0.24 2.85 4.24 2.78 0.078 1300 1100
10.2362 15.748 4.0945 409000 617000 0.12 11.5 14.5 104.7
280 420 106 1660 2790 3 312 389 51.0
23056 EMB 0.23 2.92 4.35 2.86 0.088 1100 930
11.024 16.535 4.173 373000 627000 0.12 12.3 15.3 112.2
300 460 118 2120 3540 3 336 425 71.0
23060 EMB 0.24 2.87 4.27 2.8 0.093 980 830
11.811 18.11 4.646 477000 796000 0.12 13.2 16.8 156.2
320 480 121 2200 3850 3 357 444 77.4
23064 EMB 0.23 2.93 4.36 2.86 0.096 910 780
12.598 18.898 4.764 494000 867000 0.12 14.1 17.5 170.3
340 520 133 2640 4620 4 384 481 102.7
23068 EMB 0.23 2.96 4.4 2.89 0.101 830 710
13.386 20.472 5.236 593000 1040000 0.16 15.1 18.9 225.9
360 540 134 2590 4600 4 403 499 108.3
23072 EMB 0.23 2.94 4.38 2.88 0.102 800 680
14.173 21.26 5.276 583000 1030000 0.16 15.9 19.7 238.3
380 560 135 2800 5090 4 422 520 114.2
23076 EMB 0.22 3.08 4.58 3.01 0.105 740 630
14.961 22.047 5.315 630000 1140000 0.16 16.6 20.5 251.2
400 600 148 3310 5950 4 447 555 148.7
23080 EMB 0.23 2.98 4.44 2.92 0.111 690 590
15.748 23.622 5.827 744000 1340000 0.16 17.6 21.9 327.1
420 620 150 3450 6360 4 467 576 156.0
23084 YMB 0.22 3.05 4.54 2.98 0.114 650 560
16.535 24.409 5.906 774000 1430000 0.16 18.4 22.7 343.2
(1)
Maximum shaft or housing llet radius that bearing corners will clear.
(2)
These factors apply for both inch and metric calculations. See engineering section for instructions on use.
(3)
Geometry constant for Lubrication Life Factor a31 is found in the Bearing Ratings section of the Engineering Manual (order no. 10424).
(4)
See thermal speed ratings in the Engineering Manual (order no. 10424).
NOTE: Where EJ and EM/EMB have different load ratings, the more conservative one was taken to use for both assemblies.
NOTE: Tolerance and shaft diameters are shown in tables 2 and 3 on pages 19 and 20 as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 89
SNT SPLIT PLUMMER BLOCKS
SPHERICAL ROLLER BEARING PRODUCT DATA TABLES 231 SERIES (300, 3100 SERIES SNT, FSNT)

231 SERIES B R B R B R
(300, 3100 SERIES SNT, FSNT)
Bearings are available with a tapered bore for adapter-type R R R
mounting. To order, add the sufx K to bearing number
(e.g., 23120K). Dd da Da D d da Da D d da Da
Consult your Timken engineer and www.timken.com for
up-to-date information about the availability of the bearings
you have selected.
This section lists spherical roller bearings pertinent to
Timken SNT plummer blocks. For a wider selection, consult
www.timken.com or the Timken Spherical Roller Bearing EJ EM/YM EMB/YMB
catalog (order no. 10446).

Equivalent Radial Load


Mounting Data Factors(2) Thermal
Bearing Dimensions Load Ratings Dynamic Static Geometry Speed
Bearing
Cage F__ Fa Factor(3) Ratings(4)
Part a
e __ >e In Wt.
Type Fillet(1) Backing Dia.
No. Fr Fr All
(Max.)
Bore O.D. Width Dynamic Static Shaft Housing X=1 X = 0.67 Cases
Oil Grease
d D B C Co R da Da e Y Y Y0 Cg
mm mm mm kN kN mm mm mm kg
RPM RPM
in. in. in. lbf. lbf. in. in. in. lbs.
170 280 88 1220 1710 2 195 258 21.7
23134 EJ / EM 0.28 2.39 3.55 2.33 0.091 1600 1400
6.6929 11.0236 3.4646 274000 384000 0.08 7.7 10.1 47.7
180 300 96 1410 2000 2.5 208 275 27.6
23136 EJ / EM 0.29 2.32 3.45 2.27 0.095 1500 1300
7.0866 11.811 3.7795 317000 449000 0.1 8.2 10.8 60.7
190 320 104 1630 2340 2.5 221 293 34.7
23138 EJ / EM 0.3 2.26 3.36 2.21 0.099 1400 1200
7.4803 12.5984 4.0945 365000 525000 0.1 8.7 11.5 76.3
200 340 112 1720 2400 2.5 230 308 41.1
23140 EM / EMB 0.31 2.15 3.2 2.1 0.101 1300 1200
7.874 13.3858 4.4094 386000 540000 0.1 9 12.1 90.4
220 370 120 1940 2740 3 252 336 52.8
23144 EJ / EMB 0.31 2.17 3.24 2.12 0.107 1200 1000
8.6614 14.5669 4.7244 436000 616000 0.12 9.9 13.2 116.2
240 400 128 2280 3330 3 276 364 64.9
23148 EM / EMB 0.3 2.28 3.4 2.23 0.073 1100 930
9.4488 15.748 5.0394 512000 748000 0.12 10.9 14.3 142.8
260 440 144 2440 3910 3 302 400 90.0
23152 EMB 0.30 2.23 3.31 2.18 0.086 870 760
10.236 17.323 5.669 549000 879000 0.12 11.9 15.7 198.0
280 460 146 2530 4140 4 320 419 94.5
23156 EMB 0.30 2.26 3.36 2.21 0.09 800 710
11.024 18.11 5.748 570000 930000 0.16 12.6 16.5 207.9
300 500 160 3070 5110 4 345 453 128.7
23160 EMB 0.30 2.25 3.35 2.20 0.093 710 630
11.811 19.685 6.299 691000 1150000 0.16 13.6 17.8 283.1
320 540 176 3650 5930 4 367 490 167.2
23164 EMB 0.31 2.14 3.19 2.10 0.099 650 580
12.598 21.26 6.929 819000 1330000 0.16 14.4 19.3 367.8
340 580 190 4110 6830 4 397 526 210.3
23168 EMB 0.30 2.22 3.30 2.17 0.103 590 530
13.386 22.835 7.48 924000 1540000 0.16 15.6 20.7 462.7
360 600 192 4250 7280 4 419 546 222.1
23172 EMB 0.29 2.29 3.42 2.24 0.106 560 500
14.173 23.622 7.559 956000 1640000 0.16 16.5 21.5 488.6
380 620 194 4490 7580 4 431 566 232.6
23176 EMB 0.30 2.28 3.39 2.23 0.109 530 470
14.961 24.409 7.638 1010000 1700000 0.16 17 22.3 511.7
400 650 200 4770 8110 5 454 594 261.6
23180 EMB 0.29 2.32 3.46 2.27 0.11 500 450
15.748 25.591 7.874 1070000 1820000 0.2 17.9 23.4 575.5
1)
Maximum shaft or housing llet radius that bearing corners will clear.
(2)
These factors apply for both inch and metric calculations. See engineering section for instructions on use.
(3)
Geometry constant for Lubrication Life Factor a31 is found in the Bearing Ratings section of the Engineering Manual (order no. 10424).
(4)
See thermal speed ratings in the Engineering Manual (order no. 10424).
NOTE: Where EJ and EM/EMB have different load ratings, the more conservative one was taken to use for both assemblies.
NOTE: Tolerance and shaft diameters are shown in tables 2 and 3 on pages 19 and 20 as variances from nominal bearing bore.

90 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPLIT PLUMMER BLOCKS
SPHERICAL ROLLER BEARING PRODUCT DATA TABLES 232 SERIES (500, 600 SERIES SNT, FSNT)

232 SERIES B R B R B R
(500, 600 SERIES SNT, FSNT)
Bearings are available with a tapered bore for adapter-type R R R
mounting. To order, add the sufx K to bearing number
(e.g., 23120K). Dd da Da D d da Da D d da Da
Consult your Timken engineer and www.timken.com for
up-to-date information about the availability of the bearings
you have selected.
This section lists spherical roller bearings pertinent to
Timken SNT plummer blocks. For a wider selection, consult
www.timken.com or the Timken Spherical Roller Bearing EJ EM/YM EMB/YMB
catalog (order no. 10446).

Equivalent Radial Load


Mounting Data Factors(2) Thermal
Bearing Dimensions Load Ratings Dynamic Static Geometry Speed
Bearing
Cage F__ Fa Factor(3) Ratings(4)
Part a
e __ >e In Wt.
Type Fillet(1) Backing Dia.
No. Fr Fr All
(Max.)
Bore O.D. Width Dynamic Static Shaft Housing X=1 X = 0.67 Cases
Oil Grease
d D B C Co R da Da e Y Y Y0 Cg
mm mm mm kN kN mm mm mm kg
RPM RPM
in. in. in. lbf. lbf. in. in. in. lbs.
90 160 52.4 436 521 2 107 147 4.5
23218 EJ / EM 0.3 2.28 3.4 2.23 0.074 3000 2600
3.5433 6.2992 2.063 98000 117000 0.08 4.2 5.8 9.9
100 180 60.3 554 678 2 119 164 6.6
23220 EJ / EM 0.3 2.22 3.3 2.17 0.079 2700 2300
3.937 7.0866 2.374 124000 152000 0.08 4.7 6.5 14.5
110 200 69.8 710 887 2 131 182 9.6
23222 EJ / EM 0.32 2.11 3.14 2.06 0.085 2300 2000
4.3307 7.874 2.748 160000 199000 0.08 5.2 7.2 21.1
120 215 76 824 1040 2 142 197 11.8
23224 EJ / EM 0.32 2.1 3.13 2.05 0.075 2100 1800
4.7244 8.4646 2.9921 185000 234000 0.08 5.6 7.7 26.0
130 230 80 915 1170 2.5 153 211 14.0
23226 EJ / EM 0.32 2.14 3.19 2.09 0.079 1900 1700
5.1181 9.0551 3.1496 206000 262000 0.1 6 8.3 30.8
140 250 88 1090 1410 2.5 165 229 18.5
23228 EJ / EM 0.32 2.11 3.13 2.06 0.083 1700 1500
5.5118 9.8425 3.4646 246000 317000 0.1 6.5 9 40.7
150 270 96 1270 1660 2.5 178 247 23.8
23230 EJ / EM 0.32 2.08 3.1 2.04 0.087 1500 1400
5.9055 10.6299 3.7795 286000 372000 0.1 7 9.7 52.4
160 290 104 1470 1940 2.5 190 264 30.0
23232 EJ / EM 0.33 2.06 3.06 2.01 0.091 1400 1200
6.2992 11.4173 4.0945 330000 435000 0.1 7.5 10.4 66.0
170 310 110 1660 2200 3 202 281 36.6
23234 EM 0.33 2.08 3.09 2.03 0.094 1200 1100
6.6929 12.2047 4.3307 373000 494000 0.12 8 11.1 80.5
(1)
Maximum shaft or housing llet radius that bearing corners will clear.
(2)
These factors apply for both inch and metric calculations. See engineering section for instructions on use.
(3)
Geometry constant for Lubrication Life Factor a31 is found in the Bearing Ratings section of the Engineering Manual (order no. 10424).
(4)
See thermal speed ratings in the Engineering Manual (order no. 10424).
NOTE: Where EJ and EM/EMB have different load ratings, the more conservative one was taken to use for both assemblies.
NOTE: Tolerance and shaft diameters are shown in tables 2 and 3 on pages 19 and 20 as variances from nominal bearing bore.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 91
SNT SPLIT PLUMMER BLOCKS
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES

92 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES

SNT SPHERICAL ROLLER BEARING


METRIC ACCESSORIES
Spherical roller bearing accessories are manufactured to the
same quality standards as our bearings, ensuring a secure
t to both straight and stepped shafts.
Sizes: Accessories are available for metric and inch
shaft sizes from 20 mm to 400 mm.
Features: Extensive product range, including hydraulic
assist, for integration into a full range of industrial
applications.
Benets: Supports full range of installation and removal
needs, minimizing the chance for damage to the bearing.

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Accessories Prexes and Sufxes . . . . . . . . . . . . . . . . . . . . . . . . 95
Metric Accessories Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Metric H Adapter Sleeves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Metric OH Hydraulic Adapter Sleeves . . . . . . . . . . . . . . . . . . . . 104
Metric Locknuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Metric Lockwashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Metric Lockplates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 93
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES NOMENCLATURE

NOMENCLATURE
Timken provides accessories for your every need. To complement WITHDRAWAL SLEEVES
our line of Timken spherical roller bearings, we offer bearing
Withdrawal sleeves feature a push-type mounting arrangement
sleeves and locking devices in a wide range of sizes. These
and a locking device (i.e., locknut or lockplate) to secure a bearing
accessories are manufactured to the same quality standards as
to a shaft. This design is not as widely used as the adapter
our bearings, ensuring a secure t to straight and stepped shafts.
sleeve assembly, and it does require the use of a specially
Available in sizes up to 1000 mm, bearing sleeves are available in
designed dismounting nut. The Timken part number nomenclature
two distinct designs: assembled adapter sleeves and withdrawal
for withdrawal sleeves also conforms to industry-accepted
sleeves. Reference the Timken Spherical Roller Bearing Catalog
standards. Nuts are not supplied with the withdrawal sleeve and
(order no. 10446) for the full listing of accessories.
must be ordered separately. The dismounting of large assemblies
can be eased by using a hydraulic nut (HMV).
ADAPTER SLEEVES
TABLE 23. METRIC WITHDRAWAL SLEEVE FOR
Timken adapter sleeves are used in conjunction with a nut and METRIC SHAFT SIZES
locking device to mount a tapered bore bearing onto a straight Sleeve Dismounting Nut Hydraulic Nut
shaft using a pull-type t. Smaller size assemblies (20 mm
AH standard metric/AOH KM, HM HMV
200 mm shaft) commonly use simple nuts, whereas larger hydraulic assist
assemblies (sizes >200 mm) may use HMV hydraulic nuts to assist
in mounting. Tables 21 and 22 outline our part number
nomenclature, which is consistent with world standards for LOCKING DEVICE
adapter sleeves. Timken offers a wide range of locknuts to locate bearing
TABLE 21. METRIC ADAPTER SLEEVES (H, OH) FOR assemblies on application shafts. Sometimes referred to as shaft
METRIC SHAFT SIZES ARE SUPPLIED WITH or withdrawal nuts, they are used to secure the assembly onto,
CORRESPONDING LOCKNUT AND LOCKING DEVICE
and sometimes aid with the removal from the shaft.
Sleeve Locknut Locking Device
H standard metric/OH hydraulic assist KM, KML, HM MB, MBL, MS LOCKWASHERS (MB, MBL AND W)
TABLE 22. METRIC ADAPTER SLEEVES (HA, HE) FOR
Locking washers are designed to secure the relative movement
INCH SHAFT SIZES ARE SUPPLIED WITH of a properly positioned locknut, so that a bearing and adapter
CORRESPONDING LOCKNUT AND LOCKING DEVICE sleeve remain tightly tted to a shaft or a bearing remains secure
Sleeve Locknut Locking Device against a shaft shoulder. The tab in the bore of the washer
HE standard inch (English Standard)
KM, KML MB, MBL
engages a keyway in the shaft or slot in the adapter sleeve. There
HA standard inch (American Standard)
are tabs on the O.D. of the washer that can be bent over into slots
on the circumference of the locknut. Locking washers are used
with locknuts in the KM and KML series.

LOCKPLATES (MS)
Lockplates are bolted onto the outboard face of the locknut and t
into a keyway machined in the shaft or a slot in the adapter sleeve.
MS series are mounted on metric shafts sizes with
HM locknuts.
To learn more about our spherical roller bearing accessories,
contact your Timken engineer. Standard sufxes and prexes
are found on page 95.

94 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING PLUMMER BLOCKS
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES ACCESSORIES PREFIXES AND SUFFIXES

ACCESSORIES PREFIXES AND SUFFIXES


Prex Sufx Part Description Full Description

AH Withdrawal sleeve Withdrawal sleeve

AHX Withdrawal sleeve Withdrawal sleeve modied

AOH Withdrawal sleeve hydraulic Withdrawal sleeve with oil hole on nut end

AOHX Withdrawal sleeve hydraulic Withdrawal sleeve modied with oil hole on nut end

H Adapter sleeve metric Adapter sleeve

HA Adapter sleeve metric inch shaft Metric adapter sleeves for shafts with inch dimensions (American Standards)

HE Adapter sleeve metric inch shaft Metric adapter sleeves for shafts with inch dimensions (English Standards)

KM Locknut Locknut

KML Locknut Locknut light; smaller outside diameter

HM Locknut Locknut/removal nut

HML Locknut Locknut/removal nut light

HME Locknut Locknut/removal nut with locking screw

HM.T Locknut Locknut/removal nut

HML.T Locknut Locknut/removal nut light

HMLL .T Locknut Locknut/removal nut super light

MB Lockwasher Lockwasher

MBL Lockwasher Lockwasher light

MS Lock clip Locking clip

G Sleeve Thread pitch diameter changed to ISO standard

H Locknut Additional threaded holes on locknut for locking screws (no screws)

HS Locknut Additional threaded holes on locknut for locking screws and screws

OH Adapter sleeve hydraulic Adapter sleeve with oil hole on large end (opposite to the threaded end)

OH.. H Adapter sleeve hydraulic Adapter sleeve with oil hole on nut end standard design

OH.. HB Adapter sleeve hydraulic Adapter sleeve with grooves and oil hole or two holes for bigger sizes on nut end

OH.. B Adapter sleeve hydraulic Adapter sleeve with grooves and oil hole or two holes for bigger sizes on large end
(opposite to the threaded end)

OH.. S Adapter sleeve hydraulic Adapter sleeve with oil hole on large end (opposite to the threaded end) plus nut with eight
threaded holes

OH.. BS Adapter sleeve hydraulic Adapter sleeve with grooves and oil hole or two holes for bigger sizes on large end
(opposite to the threaded end) plus nut with eight threaded holes

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 95
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC ACCESSORIES INDEX

METRIC ACCESSORIES INDEX


Bearing Bore Adapter Sleeve Withdrawal Sleeve
Bearing
Part No.
mm Metric Shaft Hydraulic Metric Shaft Metric Shaft Hydraulic Metric Shaft
25 22205K H305
30 22206K H306
35 22207K H307
40 21308K H308 AH308
40 22208K H308 AH308
40 22308K H2308 AH2308
45 21309K H309 AH309
45 22209K H309 AH309
45 22309K H2309 AH2309
50 21310K H310 AHX310
50 22210K H310 AHX310
50 22310K H2310 AHX2310
55 21311K H311 AHX311
55 22211K H311 AHX311
55 22311K H2311 AHX2311
60 21312K H312 AHX312
60 22212K H312 AHX312
60 22312K H2312 AHX2312
65 21313K H313 AH313G
65 22213K H313 AH313G
65 22313K H2313 AH2313G
70 21314K H314 AH314G
70 22214K H314 AH314G
70 22314K H2314 AHX2314G
75 21315K H315 AH315G
75 22215K H315 AH315G
75 22315K H2315 AHX2315G
80 21316K H316 AH316
80 22216K H316 AH316
80 22316K H2316 AHX2316
85 21317K H317 AHX317
85 22217K H317 AHX317
85 22317K H2317 AHX2317
90 21318K H318 AHX318
90 22218K H318 AHX318
90 22318K H2318 AHX2318
90 23218K H2318 AHX3218
95 22219K H319 AHX319
95 22319K H2319 AHX2319
100 22220K H320 AHX320
100 22320K H2320 AHX2320
100 23120K H3120 AHX3120
100 23220K H2320 AHX3220
105 23221K H2321
110 22222K H322 AHX3122
110 22322K H2322 AHX2322G
110 23022K H322 AHX322
110 23122K H3122 AHX3122
Continued on next page.

96 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC ACCESSORIES INDEX

Continued from previous page.

Bearing Bore Adapter Sleeve Withdrawal Sleeve


Bearing
Part No.
mm Metric Shaft Hydraulic Metric Shaft Metric Shaft Hydraulic Metric Shaft
110 23222K H2322 AHX3222G
110 24122K AH24122
120 22224K H3124 AHX3124
120 22324K H2324 AHX2324G
120 23024K H3024 AHX3024
120 23124K H3124 AHX3124
120 23224K H2324 AHX3224G
120 24024K AH24024
120 24124K AH24124
130 22226K H3126 AHX3126
130 22326K H2326 AHX2326G
130 23026K H3026 AHX3026
130 23126K H3126 AHX3126
130 23226K H2326 AHX3226G
130 23926K H3926
130 24026K AH24026
130 24126K AH24126
140 22228K H3128 AHX3128
140 22328K H2328 AHX2328G
140 23028K H3028 AHX3028
140 23128K H3128 AHX3128
140 23228K H2328 AHX3228G
140 23928K H3928
140 24028K AH24028
140 24128K AH24128
150 22230K H3130 AHX3130G
150 22330K H2330 AHX2330G
150 23030K H3030 AHX3030
150 23130K H3130 AHX3130G
150 23230K H2330 AHX3230G
150 23930K H3930
150 24030K AH24030
150 24130K AH24130
160 22232K H3132 OH3132H AH3132G AOH3132G
160 22332K H2332 OH2332H AH2332G AOH2332G
160 23032K H3032 OH3032H AH3032
160 23132K H3132 OH3132H AH3132G AOH3132G
160 23232K H2332 OH2332H AH3232G AOH3232G
160 23932K H3932 OH3932H
160 24032K AH24032
160 24132K AH24132
170 22234K H3134 OH3134H AH3134G AOH3134G
170 22334K H2334 OH2334H AH2334G AOH2334G
170 23034K H3034 OH3034H AH3034
170 23134K H3134 OH3134H AH3134G AOH3134G
170 23234K H2334 OH2334H AH3234G AOH3234G
170 23934K H3934 OH3934H AH3934 AOH3934
170 24034K AH24034
Continued on next page.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 97
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC ACCESSORIES INDEX

METRIC ACCESSORIES INDEX continued


Bearing Bore Adapter Sleeve Withdrawal Sleeve
Bearing
Part No.
mm Metric Shaft Hydraulic Metric Shaft Metric Shaft Hydraulic Metric Shaft
170 24134K AH24134
180 22236K H3136 OH3136H AH2236G AOH2236G
180 22336K H2336 OH2336H AH2336G AOH2336G
180 23036K H3036 OH3036H AH3036 AOH3036
180 23136K H3136 OH3136H AH3136G AOH3136G
180 23236K H2336 OH2336H AH3236G AOH3236G
180 23936K H3936 OH3936H AH3936 AOH3936
180 24036K AH24036
180 24136K AH24136
190 22238K H3138 OH3138H AH2238G AOH2238G
190 22338K H2338 OH2338H AH2338G AOH2338G
190 23038K H3038 OH3038H AH3038G AOH3038G
190 23138K H3138 OH3138H AH3138G AOH3138G
190 23238K H2338 OH2338H AH3238G AOH3238G
190 23938K H3938 OH3938H AH3938 AOH3938
190 24038K AH24038
190 24138K AH24138
200 22240K H3140 OH3140H AH2240 AOH2240
200 22340K H2340 OH2340H AH2340 AOH2340
200 23040K H3040 OH3040H AH3040G AOH3040G
200 23140K H3140 OH3140H AH3140 AOH3140
200 23240K H2340 OH2340H AH3240 AOH3240
200 23940K H3940 OH3940H AH3940 AOH3940
200 24040K AH24040
200 24140K AH24140
220 22244K H3144 OH3144H AH2244 AOH2244
220 22344K H2344 OH2344H AH2344 AOH2344
220 23044K H3044 OH3044H AH3044G AOH3044G
220 23144K H3144 OH3144H AH3144 AOH3144
220 23244K H2344 OH2344H AH2344 AOH2344
220 23944K H3944 OH3944H AH3944 AOH3944
220 24044K AH24044 AOH24044
220 24144K AH24144 AOH24144
240 22248K H3148 OH3148H AH2248 AOH2248
240 22348K H2348 OH2348H AH2348 AOH2348
240 23048K H3048 OH3048H AH3048 AOH3048
240 23148K H3148 OH3148H AH3148 AOH3148
240 23248K H2348 OH2348H AH2348 AOH2348
240 23948K H3948 OH3948H AH3948 AOH3948
240 24048K AH24048 AOH24048
240 24148K AH24148 AOH24148
260 22252K H3152 OH3152H AH2252G AOH2252G
260 22352K H2352 OH2352H AH2352G AOH2352G
260 23052K H3052 OH3052H AH3052 AOH3052
260 23152K H3152 OH3152H AH3152G AOH3152G
260 23252K H2352 OH2352H AH2352G AOH2352G
260 23952K H3952 OH3952H AH3952 AOH3952
260 24052K AOH24052G
Continued on next page.

98 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC ACCESSORIES INDEX

Continued from previous page.

Bearing Bore Adapter Sleeve Withdrawal Sleeve


Bearing
Part No.
mm Metric Shaft Hydraulic Metric Shaft Metric Shaft Hydraulic Metric Shaft
260 24152K AH24152 AOH24152
280 22256K H3156 OH3156H AH2256G AOH2256G
280 22356K H2356 OH2356H AH2356G AOH2356G
280 23056K H3056 OH3056H AH3056 AOH3056
280 23156K H3156 OH3156H AH3156G AOH3156G
280 23256K H2356 OH2356H AH2356G AOH2356G
280 23956K H3956 OH3956H AH3956 AOH3956
280 24056K AOH24056G
280 24156K AH24156 AOH24156
300 22260K H3160 OH3160H AH2260G AOH2260G
300 23060K H3060 OH3060H AH3060 AOH3060
300 23160K H3160 OH3160H AH3160G AOH3160G
300 23260K H3260 OH3260H AH3260G AOH3260G
300 23960K H3960 OH3960H AH3960 AOH3960
300 24060K AOH24060G
300 24160K AH24160 AOH24160
320 22264K H3164 OH3164H AH2264G AOH2264G
320 23064K H3064 OH3064H AH3064G AOH3064G
320 23164K H3164 OH3164H AH3164G AOH3164G
320 23264K H3264 OH3264H AH3264G AOH3264G
320 23964K H3964 OH3964H AH3964 AOH3964
320 24064K AOH24064G
320 24164K AH24164 AOH24164
340 23068K H3068 OH3068H AH3068G AOH3068G
340 23168K H3168 OH3168H AH3168G AOH3168G
340 23268K H3268 OH3268H AH3268G AOH3268G
340 23968K H3968 OH3968H AH3968 AOH3968
340 24068K AH24068 AOH24068
340 24168K AH24168 AOH24168
360 23072K H3072 OH3072H AH3072G AOH3072G
360 23172K H3172 OH3172H AH3172G AOH3172G
360 23272K H3272 OH3272H AH3272G AOH3272G
360 23972K H3972 OH3972H AH3972 AOH3972
360 24072K AH24072 AOH24072
360 24172K AH24172 AOH24172
380 23076K H3076 OH3076H AH3076G AOH3076G
380 23176K H3176 OH3176H AH3176G AOH3176G
380 23276K H3276 OH3276H AH3276G AOH3276G
380 23976K H3976 OH3976H AH3976 AOH3976
380 24076K AH24076 AOH24076
380 24176K AH24176 AOH24176
400 22380K H3280 OH3280H AH3280G AOH3280G
400 23080K H3080 OH3080H AH3080G AOH3080G
400 23180K H3180 OH3180H AH3180G AOH3180G
400 23280K H3280 OH3280H AH3280G AOH3280G
400 23980K H3980 OH3980H AH3980 AOH3980
400 24080K AH24080 AOH24080
400 24180K AH24180 AOH24180

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 99
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC H ADAPTER SLEEVES

c1
c
METRIC H ADAPTER SLEEVES c

Effective tapered bore bearing assembly.


Includes mounting sleeve, locknut and lockwasher or lockplate.
Other dimensions may be available, consult your Timken engineer.
d1 G D3 d1 G D3
L L

d1 180 mm d1 200 mm
Lockwasher Appropriate
Sleeve Part Thread(2)
d1 L C D3 C1 Weight Locknuts and Hydraulic
No.(1) G
Lockplates Nut

mm mm mm mm mm mm kg
20 H305 29 8 M 25x1.5 38 0.17 KM5 MB5
25 H306 31 8 M 30x1.5 45 0.24 KM6 MB6
30 H307 35 9 M 35x1.5 52 0.31 KM7 MB7
35 H308 36 10 M 40x1.5 58 0.42 KM8 MB8
35 H2308 46 10 M 40x1.5 58 0.22 KM8 MB8
40 H309 39 11 M 45x1.5 65 0.55 KM9 MB9
40 H2309 50 11 M 45x1.5 65 0.28 KM9 MB9
45 H310 42 12 M 50x1.5 70 0.67 KM10 MB10 HMV10
45 H2310 55 12 M 50x1.5 70 0.36 KM10 MB10 HMV10
50 H311 45 12 M 55x2 75 0.76 KM11 MB11 HMV11
50 H2311 59 12 M 55x2 75 0.42 KM11 MB11 HMV11
55 H312 47 13 M 60x2 80 0.87 KM12 MB12 HMV12
55 H2312 62 13 M 60x2 80 0.48 KM12 MB12 HMV12
60 H313 50 14 M 65x2 85 1.01 KM13 MB13 HMV13
60 H314 52 14 M 70x2 92 1.59 KM14 MB14 HMV14
60 H2313 65 14 M 65x2 85 0.56 KM13 MB13 HMV13
60 H2314 68 14 M 70x2 92 0.90 KM14 MB14 HMV14
65 H315 55 15 M 75x2 98 1.83 KM15 MB15 HMV15
65 H2315 73 15 M 75x2 98 1.05 KM15 MB15 HMV15
70 H316 59 17 M 80x2 105 2.27 KM16 MB16 HMV16
70 H2316 78 17 M 80x2 105 1.28 KM16 MB16 HMV16
75 H317 63 18 M 85x2 110 2.60 KM17 MB17 HMV17
75 H2317 82 18 M 85x2 110 1.45 KM17 MB17 HMV17
80 H318 65 18 M 90x2 120 3.02 KM18 MB18 HMV18
80 H2318 86 18 M 90x2 120 1.69 KM18 MB18 HMV18
85 H319 68 19 M 95x2 125 3.44 KM19 MB19 HMV19
85 H2319 90 19 M 95x2 125 1.92 KM19 MB19 HMV19
90 H320 71 20 M 100x2 130 3.73 KM20 MB20 HMV20
90 H3120 76 20 M 100x2 130 1.80 KM20 MB20 HMV20
90 H2320 97 20 M 100x2 130 2.15 KM20 MB20 HMV20
(1)
Adapter sleeves are supplied complete with locknuts and lockwasher or lockplates. Continued on next page.
(2)
M means metric thread and the digits are major diameter of thread and pitch.
NOTE: Sleeves are not sold separately.

100 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC H ADAPTER SLEEVES

c1
c
c

d1 G D3 d1 G D3
L L

Continued from previous page. d1 180 mm d1 200 mm


Lockwasher Appropriate
Sleeve Part Thread(2)
d1 L C D3 C1 Weight Locknuts and Hydraulic
No.(1) G
Lockplates Nut

mm mm mm mm mm mm kg
95 H321 74 20 M 105x2 140 4.30 KM 21 MB21 HMV21
95 H2321 101 20 M105x2 140 2.46 KM21 MB21 HMV21
100 H322 77 21 M 110x2 145 4.81 KM22 MB22 HMV22
100 H3122 81 21 M 110x2 145 2.25 KM22 MB22 HMV22
100 H2322 105 21 M 110x2 145 2.74 KM22 MB22 HMV22
110 H3024 72 22 M 120x2 145 1.93 KML24 MBL24 HMV24
110 H3124 88 22 M 120x2 155 2.64 KM24 MB24 HMV24
110 H2324 112 22 M 120x2 155 3.19 KM24 MB24 HMV24
115 H3926 65 23 M 130x2 155 2.40 KML26 MBL26 HMV26
115 H3026 80 23 M 130x2 155 2.85 KML26 MBL26 HMV26
115 H3126 92 23 M 130x2 165 3.66 KM26 MB26 HMV26
115 H2326 121 23 M 130x2 165 4.60 KM26 MB26 HMV26
125 H3928 66 24 M 140x2 165 2.70 KML28 MBL28 HMV28
125 H3028 82 24 M 140x2 165 3.16 KML28 MBL28 HMV28
125 H3128 97 24 M 140x2 180 4.34 KM28 MB28 HMV28
125 H2328 131 24 M 140x2 180 5.55 KM28 MB28 HMV28
135 H3930 76 26 M 150x2 180 3.60 KML30 MBL30 HMV30
135 H3030 87 26 M 150x2 180 3.89 KML30 MBL30 HMV30
135 H3130 111 26 M 150x2 195 5.52 KM30 MB30 HMV30
135 H2330 139 26 M 150x2 195 6.63 KM30 MB30 HMV30
140 H3932 78 27.5 M 160x3 190 4.60 KML32 MBL32 HMV32
140 H3032 93 27.5 M 160x3 190 5.21 KML32 MBL32 HMV32
140 H3132 119 28 M 160x3 210 7.67 KM32 MB32 HMV32
140 H2332 147 28 M 160x3 210 9.14 KM32 MB32 HMV32
150 H3934 79 27.5 M 170x3 200 5.00 KML34 MBL34 HMV34
150 H3034 101 28.5 M 170x3 200 5.99 KML34 MBL34 HMV34
150 H3134 122 29 M 170x3 220 8.38 KM34 MB34 HMV34
150 H2334 154 29 M 170x3 220 10.20 KM34 MB34 HMV34
(1)
Adapter sleeves are supplied complete with locknuts and lockwasher or lockplates. Continued on next page.
(2)
M means metric thread and the digits are major diameter of thread and pitch.
NOTE: Sleeves are not sold separately.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 101
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC H ADAPTER SLEEVES

c1
c
METRIC H ADAPTER SLEEVES continued c

Effective tapered bore bearing assembly.


Includes mounting sleeve, locknut and lockwasher or lockplate.
Other dimensions may be available, consult your Timken engineer.
d1 G D3 d1 G D3
L L

Continued from previous page. d1 180 mm d1 200 mm


Lockwasher Appropriate
Sleeve Part Thread(2)(3)
d1 L C D3 C1 Weight Locknuts and Hydraulic
No.(1) G
Lockplates Nut

mm mm mm mm mm mm kg
160 H3936 87 29.5 M 180x3 210 5.70 KML36 MBL36 HMV36
160 H3036 109 29.5 M 180x3 210 6.83 KML36 MBL36 HMV36
160 H3136 131 30 M 180x3 230 9.50 KM36 MB36 HMV36
160 H2336 161 30 M 180x3 230 11.30 KM36 MB36 HMV36
170 H3938 89 30.5 M 190x3 220 6.19 KML38 MBL38 HMV38
170 H3038 112 30.5 M 190x3 220 7.45 KML38 MBL38 HMV38
170 H3138 141 31 M 190x3 240 10.80 KM38 MB38 HMV38
170 H2338 169 31 M 190x3 240 12.60 KM38 MB38 HMV38
180 H3940 98 31.5 M 200x3 240 7.89 KML40 MBL40 HMV40
180 H3040 120 31.5 M 200x3 240 9.19 KML40 MBL40 HMV40
180 H3140 150 32 M 200x3 250 12.10 KM40 MB40 HMV40
180 H2340 176 32 M 200x3 250 13.90 KM40 MB40 HMV40
200 H3944 96 30 Tr 220x4 260 41 8.16 HM3044 MS3044 HMV44
200 H3044 126 30 Tr 220x4 260 41 10.30 HM3044 MS3044 HMV44
200 H3144 161 35 Tr 220x4 280 15.10 HM44T MB44 HMV44
200 H2344 186 35 Tr 220x4 280 17.00 HM44T MB44 HMV44
220 H3948 101 34 Tr 240x4 290 46 11.00 HM3048 MS3048 HMV48
220 H3048 133 34 Tr 240x4 290 46 13.20 HM3048 MS3048 HMV48
220 H3148 172 37 Tr 240x4 300 17.60 HM48T MS48 HMV48
220 H2348 199 37 Tr 240x4 300 20.00 HM48T MS48 HMV48
240 H3952 116 34 Tr 260x4 310 46 12.80 HM3052 MS3052 HMV52
240 H3052 145 34 Tr 260x4 310 46 15.30 HM3052 MS3052 HMV52
240 H3152 190 39 Tr 260x4 330 22.30 HM52T MB52 HMV52
240 H2352 211 39 Tr 260x4 330 24.50 HM52T MB52 HMV52
260 H3956 121 38 Tr 280x4 330 50 15.30 HM3056 MS3056 HMV56
260 H3056 152 38 Tr 280x4 330 50 17.70 HM3056 MS3056 HMV56
260 H3156 195 41 Tr 280x4 350 25.10 HM56T MB56 HMV56
260 H2356 224 41 Tr 280x4 350 28.40 HM56T MB56 HMV56
280 H3960 140 42 Tr 300x4 360 54 20.00 HM3060 MS3060 HMV60
280 H3060 168 42 Tr 300x4 360 54 22.80 HM3060 MS3060 HMV60
280 H3160 208 40 Tr 300x4 380 53 30.20 HM3160 MS3160 HMV60
280 H3260 240 40 Tr 300x4 380 53 34.10 HM3160 MS3160 HMV60
300 H3964 140 42 Tr 320x5 380 55 21.50 HM3064 MS3064 HMV64
300 H3064 171 42 Tr 320x5 380 55 24.60 HM3064 MS3064 HMV64
300 H3164 226 42 Tr 320x5 400 56 34.90 HM3164 MS3164 HMV64
300 H3264 258 42 Tr 320x5 400 56 39.30 HM3164 MS3164 HMV64
(1)
Adapter sleeves are supplied complete with locknuts and lockwasher or lockplates. Continued on next page.
(2)
M means metric thread and the digits are major diameter of thread and pitch.
(3)
Tr means 30. Trapezoid thread and the digits are outside diameter of thread and pitch.
NOTE: Sleeves are not sold separately.

102 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC H ADAPTER SLEEVES

c1
c
c

d1 G D3 d1 G D3
L L

Continued from previous page. d1 180 mm d1 200 mm


Lockwasher Appropriate
Sleeve Part Thread(2)
d1 L C D3 C1 Weight Locknuts and Hydraulic
No.(1) G
Lockplates Nut

mm mm mm mm mm mm kg
320 H3968 144 45 Tr 340x5 400 58 24.50 HM3068 MS3068 HMV68
320 H3068 187 45 Tr 340x5 400 58 28.70 HM3068 MS3068 HMV68
320 H3168 254 55 Tr 340x5 440 72 50.00 HM3168 MS3168 HMV68
320 H3268 288 55 Tr 340x5 440 72 54.60 HM3168 MS3168 HMV68
340 H3972 144 45 Tr 360x5 420 58 25.20 HM3072 MS3072 HMV72
340 H3072 188 45 Tr 360x5 420 58 30.50 HM3072 MS3072 HMV72
340 H3172 259 58 Tr 360x5 460 75 56.00 HM3172 MS3172 HMV72
340 H3272 299 58 Tr 360x5 460 75 60.60 HM3172 MS3172 HMV72
360 H3976 164 48 Tr 380x5 450 62 31.50 HM3076 MS3076 HMV76
360 H3076 193 48 Tr 380x5 450 62 35.80 HM3076 MS3076 HMV76
360 H3176 264 60 Tr 380x5 490 77 61.70 HM3176 MS3176 HMV76
360 H3276 310 60 Tr 380x5 490 77 69.60 HM3176 MS3176 HMV76
380 H3980 168 52 Tr 400x5 470 66 35.00 HM3080 MS3080 HMV80
380 H3080 210 52 Tr 400x5 470 66 41.30 HM3080 MS3080 HMV80
380 H3180 272 62 Tr 400x5 520 82 73.00 HM3180 MS3180 HMV80
380 H3280 328 62 Tr 400x5 520 82 81.00 HM3180 MS3180 HMV80
400 H3984 168 52 Tr 420x5 490 66 36.60 HM3084 MS3084 HMV84
400 H3084 212 52 Tr 420x5 490 66 43.70 HM3084 MS3084 HMV84
400 H3184 304 70 Tr 420x5 540 90 84.20 HM3184 MS3184 HMV84
400 H3284 352 70 Tr 420x5 540 90 96.00 HM3184 MS3184 HMV84
410 H3988 189 60 Tr 440x5 520 77 58.00 HM3088 MS3088 HMV88
410 H3088 228 60 Tr 440x5 520 77 65.20 HM3088 MS3088 HMV88
410 H3188 307 70 Tr 440x5 560 90 104.00 HM3188 MS3188 HMV88
410 H3288 361 70 Tr 440x5 560 90 118.00 HM3188 MS3188 HMV88
430 H3992 189 60 Tr 460x5 540 77 60.00 HM3092 MS3092 HMV92
430 H3192 326 75 Tr 460x5 580 95 116.00 HM3192 MS3192 HMV92
430 H3292 382 75 Tr 460x5 580 95 134.00 HM3192 MS3192 HMC92
450 H3996 200 60 Tr 480x5 560 77 66.00 HM3096 MS3096 HMV96
450 H3296 397 75 Tr 480x5 620 95 153.00 HM3196 MS3196 HMV96
(1)
Adapter sleeves are supplied complete with locknuts and lockwasher or lockplates.
(2)
Tr means 30. Trapezoid thread and the digits are outside diameter of thread and pitch.
NOTE: Sleeves are not sold separately.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 103
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC OH HYDRAULIC ADAPTER SLEEVES

c1
c
METRIC OH HYDRAULIC c
Ro
ADAPTER SLEEVES t
e

Includes sleeve, nut and lockwasher


or lockplate.
Hydraulic assistance facilitates mounting d1 G D3
L
d1 G D3

of large bearing. Oil pump required to L


inject pressurized oil.
Other dimensions may be available,
consult your Timken engineer.

d1 180 mm d1 200 mm
Lockwasher Appropriate
Sleeve Part Thread(2)(3)
d1 L C D3 C1(4) Ro e t Weight Locknuts and Hydraulic
No.(1) G
Lockplate Nut

mm mm mm mm mm mm mm mm kg
140 OH3032H 93 27.5 M 160x3 190 4 7 5.21 KML32 MBL32 HMV32
140 OH3132H 119 28 M 160x3 210 4 7 7.67 KM32 MB32 HMV32
150 OH3034H 101 28.5 M 170x3 200 4 7 5.99 KML34 MBL34 HMV34
150 OH3134H 122 29 M 170x3 220 4 7 8.38 KM34 MB34 HMV34
160 OH3936H 87 29.5 M 180x3 210 4 7 5.70 KML36 MBL36 HMV36
160 OH3036H 109 29.5 M 180x3 210 4 7 6.83 KML36 MBL36 HMV36
160 OH3136H 131 30 M 180x3 230 4 7 9.50 KM36 MB36 HMV36
170 OH3938H 89 30.5 M 190x3 220 4 7 6.19 KML38 MBL38 HMV38
170 OH3038H 112 30.5 M 190x3 220 4 7 7.45 KML38 MBL38 HMV38
170 OH3138H 141 31 M 190x3 240 4 7 10.80 KM38 MB38 HMV38
170 OH2338H 169 31 M 190x3 240 4 7 12.60 KM38 MB38 HMV38
180 OH3940H 98 31.5 M 200x3 240 4 7 7.89 KML40 MBL40 HMV40
180 OH3040H 120 31.5 M 200x3 240 4 7 9.19 KML40 MBL40 HMV40
180 OH3140H 150 32 M 200x3 250 4 7 12.10 KM40 MB40 HMV40
180 OH2340H 176 32 M 200x3 250 4 7 13.90 KM40 MB40 HMV40
200 OH3944H 96 30 Tr 220x4 260 41 M6 4 7 8.16 HM3044 MS3044 HMV44
200 OH3044H 126 30 Tr 220x4 260 41 M6 4 7 10.30 HM3044 MS3044 HMV44
200 OH3144H 161 35 Tr 220x4 280 M6 4 7 15.10 HM44T MB44 HMV44
200 OH2344H 186 35 Tr 220x4 280 M6 4 7 17.00 HM44T MB44 HMV44
220 OH3948H 101 34 Tr 240x4 290 46 M6 4 7 11.00 HM3048 MS3048 HMV48
220 OH3048H 133 34 Tr 240x4 290 46 M6 4 7 13.20 HM3048 MS3048 HMV48
220 OH3148H 172 37 Tr 240x4 300 M6 4 7 17.60 HM48T MB48 HMV48
220 OH2348H 199 37 Tr 240x4 300 M6 4 7 20.00 HM48T MB48 HMV48
240 OH3952H 116 34 Tr 260x4 310 46 M6 4 7 12.80 HM3052 MS3052 HMV52
240 OH3052H 145 34 Tr 260x4 310 46 M6 4 7 15.30 HM3052 MS3052 HMV52
240 OH3152H 190 39 Tr 260x4 330 M6 4 7 22.30 HM52T MB52 HMV52
240 OH2352H 211 39 Tr 260x4 330 M6 4 7 24.50 HM52T MB52 HMV52
(1)
Hydraulic adapter sleeves are supplied complete with locknuts and lockwasher or lockplates. Continued on next page.
(2)
M means metric thread and the digits are major diameter of thread and pitch.
(3)
Tr means 30. Trapezoid thread and the digits are outside diameter of thread and pitch.
(4)
Adapters with dimensions C1 have a locking device as shown in the illustration.

104 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC OH HYDRAULIC ADAPTER SLEEVES

c1
c
c
Ro
e
t

d1 G D3 d1 G D3
L L

Continued from previous page. d1 180 mm d1 200 mm


Lockwasher Appropriate
Sleeve Part Thread(2)
d1 L C D3 C1(3) Ro e t Weight Locknuts and Hydraulic
No.(1) G
Lockplate Nut

mm mm mm mm mm mm mm mm kg
260 OH3956H 121 38 Tr 280x4 330 50 M6 4 7 15.30 HM3056 MS3056 HMV56
260 OH3056H 152 38 Tr 280x4 330 50 M6 4 7 17.70 HM3056 MS3056 HMV56
260 OH3156H 195 41 Tr 280x4 350 M6 4 7 25.10 HM56T MB56 HMV56
260 OH2356H 224 41 Tr 280x4 350 M6 4 7 28.40 HM56T MB56 HMV56
280 OH3960H 140 42 Tr 300x4 360 54 M6 4 7 20.00 HM3060 MS3060 HMV60
280 OH3060H 168 42 Tr 300x4 360 54 M6 4 7 22.80 HM3060 MS3060 HMV60
280 OH3160H 208 40 Tr 300x4 380 53 M6 4 7 30.20 HM3160 MS3160 HMV60
280 OH3260H 240 40 Tr 300x4 380 53 M6 4 7 34.10 HM3160 MS3160 HMV60
300 OH3964H 140 42 Tr 320x5 380 55 M6 3.5 7 21.50 HM3064 MS3064 HMV64
300 OH3064H 171 42 Tr 320x5 380 55 M6 3.5 7 24.60 HM3064 MS3064 HMV64
300 OH3164H 226 42 Tr 320x5 400 56 M6 3.5 7 34.90 HM3164 MS3164 HMV64
300 OH3264H 258 42 Tr 320x54 400 56 M6 3.5 7 39.30 HM3164 MS3164 HMV64
320 OH3968H 144 45 Tr 340x5 400 58 M6 3.5 7 24.50 HM3068 MS3068 HMV68
320 OH3068H 187 45 Tr 340x5 400 58 M6 3.5 7 28.70 HM3068 MS3068 HMV68
320 OH3168H 254 55 Tr 340x5 440 72 M6 3.5 7 50.00 HM3168 MS3168 HMV68
320 OH3268H 288 55 Tr 340x5 440 72 M6 3.5 7 54.60 HM3168 MS3168 HMV68
340 OH3972H 144 45 Tr 360x5 420 58 M6 3.5 7 25.20 HM3072 MS3072 HMV72
340 OH3072H 188 45 Tr 360x5 420 58 M6 3.5 7 30.50 HM3072 MS3072 HMV72
340 OH3172H 259 58 Tr 360x5 460 75 M6 3.5 7 56.00 HM3172 MS3172 HMV72
340 OH3272H 299 58 Tr 360x5 460 75 M6 3.5 7 60.60 HM3172 MS3172 HMV72
360 OH3976H 164 48 Tr 380x5 450 62 M6 3.5 7 31.50 HM3076 MS3076 HMV76
360 OH3076H 193 48 Tr 380x5 450 62 M6 3.5 7 35.80 HM3076 MS3076 HMV76
360 OH3176H 264 60 Tr 380x5 490 77 M6 3.5 7 61.70 HM3176 MS3176 HMV76
360 OH3276H 310 60 Tr 380x5 490 77 M6 3.5 7 69.60 HM3176 MS3176 HMV76
380 OH3980H 168 52 Tr 400x5 470 66 M6 3.5 7 35.00 HM3080 MS3080 HMV80
380 OH3080H 210 52 Tr 400x5 470 66 M6 3.5 7 41.30 HM3080 MS3080 HMV80
380 OH3180H 272 62 Tr 400x5 520 82 M6 3.5 7 73.00 HM3180 MS3180 HMV80
380 OH3280H 328 62 Tr 400x5 520 82 M6 3.5 7 81.00 HM3180 MS3180 HMV80
(1)
Hydraulic adapter sleeves are supplied complete with locknuts and lockwasher or lockplates. Continued on next page.
(2)
Tr means 30. Trapezoid thread and the digits are outside diameter of thread and pitch.
(3)
Adapters with dimensions C1 have a locking device as shown in the illustration.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 105
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC OH HYDRAULIC ADAPTER SLEEVES

c1
c
METRIC OH HYDRAULIC c
Ro
ADAPTER SLEEVES continued t
e

Includes sleeve, nut and lockwasher


or lockplate.
Hydraulic assistance facilitates mounting d1 G D3
L
d1 G D3

of large bearing. Oil pump required to L


inject pressurized oil.
Other dimensions may be available,
consult your Timken engineer.

Continued from previous page. d1 180 mm d1 200 mm


Lockwasher Appropriate
Sleeve Part Thread(2)
d1 L C D3 C1(3) Ro e t Weight Locknuts and Hydraulic
No.(1) G
Lockplate Nut

mm mm mm mm mm mm mm mm kg
400 OH3984H 168 52 Tr 420x5 490 66 M6 3.5 7 36.60 HM3084 MS3084 HMV84
400 OH3084H 212 52 Tr 420x5 490 66 M6 3.5 7 43.70 HM3084 MS3084 HMV84
400 OH3184H 304 70 Tr 420x5 540 90 M6 3.5 7 84.20 HM3184 MS3184 HMV84
400 OH3284H 352 70 Tr 420x5 540 90 M6 3.5 7 96.00 HM3184 MS3184 HMV84
410 OH3988H 189 60 Tr 440x5 520 77 M8 6.5 12 58.00 HM3088 MS3088 HMV88
410 OH3088H 228 60 Tr 440x5 520 77 M8 6.5 12 65.20 HM3088 MS3088 HMV88
410 OH3188H 307 70 Tr 440x5 560 90 M8 6.5 12 104.00 HM3188 MS3188 HMV88
410 OH3288H 361 70 Tr 440x5 560 90 M8 6.5 12 118.00 HM3188 MS3188 HMV88
430 OH3992H 189 60 Tr 460x5 540 77 M8 6.5 12 60.00 HM3092 MS3092 HMV92
430 OH3092H 234 60 Tr 460x5 540 77 M8 6.5 12 71.00 HM3092 MS3092 HMV92
430 OH3192H 326 75 Tr 460x5 580 95 M8 6.5 12 116.00 HM3192 MS3192 HMV92
430 OH3292H 382 75 Tr 460x5 580 95 M8 6.5 12 134.00 HM3192 MS3192 HMV92
450 OH3996H 200 60 Tr 480x5 560 77 M8 6.5 12 66.00 HM3096 MS30/96 HMV96
450 OH3096H 237 60 Tr 480x5 560 77 M8 6.5 12 75.00 HM3096 MS30/96 HMV96
450 OH3196H 335 75 Tr 480x5 620 95 M8 6.5 12 135.00 HM3196 MS3196 HMV96
450 OH3296H 397 75 Tr 480x5 620 95 M8 6.5 12 153.00 HM3196 MS3196 HMV96
470 OH39/500H 208 68 Tr 500x5 580 85 M8 6.5 12 74.30 HM30/500 MS30/500 HMV100
470 OH31/500H 356 80 Tr 500x5 630 100 M8 6.5 12 145.00 HM31/500 MS31/500 HMV100
470 OH32/500H 428 80 Tr 500x5 630 100 M8 6.5 12 166.00 HM31/500 MS31/500 HMV100
500 OH39/530H 216 68 Tr 530x6 630 90 M8 6 12 87.90 HM30/530 MS30/530 HMV106
500 OH31/530H 364 80 Tr 530x6 670 105 M8 6 12 161.00 HM31/530 MS31/530 HMV106
500 OH32/530H 447 80 Tr 530x6 670 105 M8 6 12 192.00 HM31/530 MS31/530 HMV106
530 OH39/560H 227 75 Tr 560x6 650 97 M8 6 12 95.00 HM30/560 MS30/560 HMV112
530 OH31/560H 377 85 Tr 560x6 710 110 M8 6 12 185.00 HM31/560 MS31/560 HMV112
530 OH32/560H 462 85 Tr 560x6 710 110 M8 6 12 219.00 HM31/560 MS31/560 HMV112
560 OH39/600H 239 75 Tr 600x6 700 97 G1/8 8 13 127.00 HM30/600 MS30/600 HMV120
560 OH30/600H 289 75 Tr 600x6 700 97 G1/8 8 13 147.00 HM30/600 MS30/600 HMV120
560 OH31/600H 399 85 Tr 600x6 750 110 G1/8 8 13 234.00 HM31/600 MS31/600 HMV120
560 OH32/600H 487 85 Tr 600x6 750 110 G1/8 8 13 278.00 HM31/600 MS31/600 HMV120
600 OH39/630H 254 75 Tr 630x6 730 97 M8 6 12 124.00 HM30/630 MS30/630 HMV126
600 OH30/630H 301 75 Tr 630x6 730 97 M8 6 12 138.00 HM30/630 MS30/630 HMV126
600 OH31/630H 424 95 Tr 630x6 800 120 M8 6 12 254.00 HM31/630 MS31/630 HMV126
600 OH32/630H 521 95 Tr 630x6 800 120 M8 6 12 300.00 HM 31/630 MS31/630 HMV126
(1)
Hydraulic adapter sleeves are supplied complete with locknuts and lockwasher or lockplates. Continued on next page.
(2)
Tr means 30. Trapezoid thread and the digits are outside diameter of thread and pitch.
(3)
Adapters with dimensions C1 have a locking device as shown in the illustration.

106 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC OH HYDRAULIC ADAPTER SLEEVES

c1
c
c
Ro
e
t

d1 G D3 d1 G D3
L L

Continued from previous page. d1 180 mm d1 200 mm


Lockwasher Appropriate
Sleeve Part Thread(2)
d1 L C D3 C1(3) Ro e t Weight Locknuts and Hydraulic
No.(1) G
Lockplate Nut

mm mm mm mm mm mm mm mm kg
630 OH39/670H 264 80 Tr 670x6 780 102 G1/8 8 13 162.00 HM30/670 MS30/670 HMV134
630 OH30/670H 324 80 Tr 670x6 780 102 G1/8 8 13 190.00 HM30/670 MS30/670 HMV134
630 OH31/670H 456 106 Tr 670x6 850 131 G1/8 8 13 340.00 HM31/670 MS31/670 HMV134
630 OH32/670H 558 106 Tr 670x6 850 131 G1/8 8 13 401.00 HM31/670 MS31/670 HMV134
670 OH39/710H 286 90 Tr 710x7 830 112 G1/8 8 13 183.00 HM30/710 MS30/710 HMV142
670 OH30/710H 342 90 Tr 710x7 830 112 G1/8 8 13 228.00 HM30/710 MS30/710 HMV142
670 OH31/710H 467 106 Tr 710x7 900 135 G1/8 8 13 392.00 HM31/710 MS31/710 HMV142
670 OH32/710H 572 106 Tr 710x7 900 135 G1/8 8 13 459.00 HM31/710 MS31/710 HMV142
710 OH39/750H 291 90 Tr 750x7 870 112 G1/8 8 13 211.00 HM30/750 MS30/750 HMV150
710 OH30/750H 356 90 Tr 750x7 870 112 G1/8 8 13 246.00 HM30/750 MS30/750 HMV150
710 OH31/750H 493 112 Tr 750x7 950 141 G1/8 8 13 451.00 HM31/750 MS31/750 HMV150
710 OH32/750H 603 112 Tr 750x7 950 141 G1/8 8 13 526.00 HM31/750 MS31/750 HMV150
750 OH39/800H 303 90 Tr 800x7 920 112 G1/8 10 13 259.00 HM30/800 MS30/800 HMV160
750 OH31/800H 505 112 Tr 800x7 1000 141 G1/8 10 13 535.00 HM31/800 MS31/800 HMV160
750 OH32/800H 618 112 Tr 800x7 1000 141 G1/8 10 13 629.00 HM31/800 MS31/800 HMV160
800 OH39/850H 308 90 Tr 850x7 980 115 G1/8 10 13 288.00 HM30/850 MS30/850 HMV170
800 OH31/850H 536 118 Tr 850x7 1060 147 G1/8 10 13 616.00 HM31/850 MS31/850 HMV170
800 OH32/850H 651 118 Tr 850x7 1060 147 G1/8 10 13 722.00 HM31/850 MS31/850 HMV170
850 OH39/900H 326 100 Tr 900x7 1030 125 G1/8 10 13 330.00 HM30/900 MS30/900 HMV180
850 OH31/900H 557 125 Tr 900x7 1120 154 G1/8 10 13 677.00 HM31/900 MS31/900 HMV180
850 OH32/900H 660 125 Tr 900x7 1120 154 G1/8 10 13 776.00 HM31/900 MS31/900 HMV180
900 OH39/950H 344 100 Tr 950x8 1080 125 G1/8 10 13 362.00 HM30/950 MS30/950 HMV190
900 OH31/950H 583 125 Tr 950x8 1170 154 G1/8 10 13 738.00 HM31/950 MS31/950 HMV190
900 OH32/950H 675 125 Tr 950x8 1170 154 G1/8 10 13 834.00 HM31/950 MS31/950 HMV190
950 OH39/1000H 358 100 Tr 1000x8 1140 125 G1/8 10 13 407.00 HM30/1000 MS30/1000 HMV200
950 OH31/1000H 609 125 Tr 1000x8 1240 154 G1/8 10 13 842.00 HM31/1000 MS31/1000 HMV200
950 OH32/1000H 707 125 Tr 1000x8 1240 154 G1/8 10 13 952.00 HM31/1000 MS31/1000 HMV200
1000 OH39/1060H 372 100 Tr 1060x8 1200 125 G1/8 12 15 490.00 HM30/1060 MS30/1000 HMV212
1000 OH30/1060H 447 100 Tr 1060x8 1200 125 G1/8 12 15 571.00 HM30/1060 MS30/1000 HMV212
1000 OH31/1060H 622 125 Tr 1060x8 1300 154 G1/8 12 15 984.00 HM31/1060 MS31/1000 HMV212
(1)
Hydraulic adapter sleeves are supplied complete with locknuts and lockwasher or lockplates.
(2)
Tr means 30. Trapezoid thread and the digits are outside diameter of thread and pitch.
(3)
Adapters with dimensions C1 have a locking device as shown in the illustration.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 107
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC LOCKNUTS

METRIC LOCKNUTS s
Bn
30
T

D3 D1 D6 D4

Locknut Thread(2) Lockwasher


D3 D4 Bn s T D6 Weight
No.(1) D1 No.

mm mm mm mm mm mm mm kg
KM0 M 10 X 0.75 18 13 4 3 2 10.5 0.01 MB00
KM1 M 12 X 1.0 22 17 4 3 2 12.5 0.01 MB01
KM2 M 15 X 1.0 25 21 5 4 2 15.5 0.01 MB02
KM3 M 17 X 1.0 28 24 5 4 2 17.5 0.01 MB03
KM4 M 20 X 1.0 32 26 6 4 2 20.5 0.02 MB04
KM5 M 25 X 1.5 38 32 7 5 2 25.8 0.03 MB05
KM6 M 30 X 1.5 45 38 7 5 2 30.8 0.04 MB06
KM7 M 35 X 1.5 52 44 8 5 2 35.8 0.05 MB07
KM8 M 40 X 1.5 58 50 9 6 2.5 40.8 0.09 MB08
KM9 M 45 X 1.5 65 56 10 6 2.5 45.8 0.12 MB09
KM10 M 50 X 1.5 70 61 11 6 2.5 50.8 0.15 MB10
KM11 M 55 X 2.0 75 67 11 7 3 56.0 0.16 MB11
KM12 M 60 X 2.0 80 73 11 7 3 61.0 0.17 MB12
KM13 M 65 X 2.0 85 79 12 7 3 66.0 0.20 MB13
KM14 M 70 X 2.0 92 85 12 8 3.5 71.0 0.24 MB14
KM15 M 75 X 2.0 98 90 13 8 3.5 76.0 0.29 MB15
KM16 M 80 X 2.0 105 95 15 8 3.5 81.0 0.40 MB16
KM17 M 85 X 2.0 110 102 16 8 3.5 86.0 0.45 MB17
KM18 M 90 X 2.0 120 108 16 10 4 91.0 0.56 MB18
KM19 M 95 X 2.0 125 113 17 10 4 96.0 0.66 MB19
KM20 M 100 X 2.0 130 120 18 10 4 101.0 0.70 MB20
KM21 M 105 X 2.0 140 126 18 12 5 106.0 0.85 MB21
KM22 M 110 X 2.0 145 133 19 12 5 111.0 0.97 MB22
KM23 M 115 X 2.0 150 137 19 12 5 116.0 1.01 MB23
KM24 M 120 X 2.0 160 148 21 12 5 126.0 1.80 MB24
KM25 M 125 X 2.0 160 148 21 12 5 126.0 1.19 MB25
KM26 M 130 X 2.0 165 149 21 12 5 131.0 1.25 MB26
KM27 M 135 X 2.0 175 160 22 14 6 136.0 1.55 MB27
KM28 M 140 X 2.0 180 160 22 14 6 141.0 1.56 MB28
KM29 M145 X 2.0 190 172 24 14 6 146.0 2.00 MB29

(1)
No. KM0-KM40 also available in 304 stainless steel. Continued on next page.
(2)
M means metric thread and the digits are major diameter of thread and pitch.

108 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC LOCKNUTS

Bn
s
30
T

D3 D1 D6 D4

Continued from previous page.

Locknut Thread(2) Lockwasher


D3 D4 Bn s T D6 Weight
No.(1) D1 No.

mm mm mm mm mm mm mm kg
KM30 M150 X 2.0 195 171 24 14 6 151.0 2.03 MB30
KM31 M155 X 3.0 200 182 25 16 7 156.5 2.21 MB31
KM32 M160 X 3.0 210 182 25 16 7 161.5 2.59 MB32
KM33 M165 X 3.0 210 193 26 16 7 166.5 2.43 MB33
KM34 M170 X 3.0 220 193 26 16 7 171.5 2.80 MB34
KM36 M180 X 3.0 230 203 27 18 8 181.5 3.07 MB36
KM38 M190 X 3.0 240 214 28 18 8 191.5 3.39 MB38
KM40 M200 X 3.0 250 226 29 18 8 201.5 3.69 MB40
(1)
No. KM0 - KM40 also available in 304 stainless steel.
(2)
M means metric thread and the digits are major diameter of thread and pitch.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 109
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC LOCKNUTS

METRIC LOCKNUTS continued s


Bn
30
T

D3 D1 D6 D4

Locknut Thread(1)
D3 D4 Bn s T D6 Weight
No. D1

mm mm mm mm mm mm mm kg
HM42 Tr 210 x 4 270 238 30 20 10 212 4.75
HM44 Tr 220 x 4 280 250 32 20 10 222 5.35
HM46 Tr 230 x 4 290 260 34 20 10 232 5.80
HM48 Tr 240 x 4 300 270 34 20 10 242 6.20
HM50 Tr 250 x 4 320 290 36 20 10 252 7.00
HM52 Tr 260 x 4 330 300 36 24 12 262 8.55
HM54 Tr 270 x 4 340 310 38 24 12 272 9.20
HM56 Tr 280 x 4 350 320 38 24 12 282 10.00
HM58 Tr 290 x 4 370 330 40 24 12 292 11.80
HM60 Tr 300 x 4 380 340 40 24 12 302 12.00
HM62 Tr 310 x 5 390 350 42 24 12 312.5 13.40
HM64 Tr 320 x 5 400 360 42 24 12 322.5 13.50
HM66 Tr 330 x 5 420 380 52 28 15 332.5 20.40
HM68 Tr 340 x 5 440 400 55 28 15 342.5 24.50
HM70 Tr 350 x 5 450 410 55 28 15 352.5 25.20
HM72 Tr 360 x 5 460 420 58 28 15 362.5 27.50
HM74 Tr 370 x 5 470 430 58 28 15 372.5 28.20
HM76 Tr 380 x 5 490 450 60 32 18 382.5 33.50
HM80 Tr 400 x 5 520 470 62 32 18 402.5 40.00
(1)
Tr means 30; trapezoid thread and the digits are major diameter of thread and pitch.

110 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC LOCKNUTS

Bn
s
30
T

D3 Dp D1 D6 D4

Tapped Appropriate
Locknut Thread(1)
D3 D4 s T D6 Bn i Hole Dp Lockplate Weight
No. D1
Threads No.

mm mm mm mm mm mm mm mm mm kg

HM3044 Tr 220 x 4 260 242 20 9 222 30 12 M6x1 229 MS3044 3.09

HM3048 Tr 240 x 4 290 270 20 10 242 34 15 M 8 x 1.25 253 MS3048 5.16

HM3052 Tr 260 x 4 310 290 20 10 262 34 15 M 8 x 1.25 273 MS3052 5.67

HM3056 Tr 280 x 4 330 310 24 10 282 38 15 M 8 x 1.25 293 MS3056 6.78

HM3060 Tr 300 x 4 360 336 24 12 302 42 15 M 8 x 1.25 316 MS3060 9.62

HM3064 Tr 320 x 5 380 356 24 12 322.5 42 15 M 8 x 1.25 335 MS3064 9.94

HM3068 Tr 340 x 5 400 376 24 12 342.5 45 15 M 8 x 1.25 355 MS3068 11.70

HM3072 Tr 360 x 5 420 394 28 13 362.5 45 15 M 8 x 1.25 374 MS3072 12.00

HM3076 Tr 380 x 5 450 422 28 14 382.5 48 18 M 10 x 1.5 398 MS3076 14.90

HM3080 Tr 400 x 5 470 442 28 14 402.5 52 18 M 10 x 1.5 418 MS3080 16.90

HM3084 Tr 420 x 5 490 462 32 14 422.5 52 18 M 10 x 1.5 438 MS3084 17.40

HM3088 Tr 440 x 5 520 490 32 15 442.5 60 21 M 12 x 1.75 462 MS3088 26.20

HM3092 Tr 460 x 5 540 510 32 15 462.5 60 21 M 12 x 1.75 482 MS3092 29.60

HM3096 Tr 480 x 5 560 530 36 15 482.5 60 21 M 12 x 1.75 502 MS3096 28.30

HM30/500 Tr 500 x 5 580 550 36 15 502.5 68 21 M 12 x 1.75 522 MS30/500 33.60


(1)
Tr means 30; trapezoid thread and the digits are major diameter of thread and pitch.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 111
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC LOCKNUTS

METRIC LOCKNUTS continued s


Bn
30
T

D3 Dp D1 D6 D4

Appropriate
Locknut Thread(1) Tapped Hole
D3 D4 s T D6 Bn i Dp Lockplate Weight
No. D1 Threads
No.

mm mm mm mm mm mm mm mm mm kg

HM3144 Tr 220 x 4 280 250 20 10 222 32 15 M 8 x 1.25 238 MS3144 5.20

HM3148 Tr 240 x 4 300 270 20 10 242 34 15 M 8 x 1.25 258 MS3148 5.95

HM3152 Tr 260 x 4 330 300 24 12 262 36 18 M 10 x 1.5 281 MS3152 8.05

HM3156 Tr 280 x 4 350 320 24 12 282 38 18 M 10 x 1.5 301 MS3156 9.05

HM3160 Tr 300 x 4 380 340 24 12 302 40 18 M 10 x 1.5 326 MS3160 11.80

HM3164 Tr 320 x 5 400 360 24 12 322.5 42 18 M 10 x 1.5 345 MS3164 13.10

HM3168 Tr 340 x 5 440 400 28 15 342.5 55 21 M 12 x 1.75 372 MS3168 23.10

HM3172 Tr 360 x 5 460 420 28 15 362.5 58 21 M 12 x 1.75 392 MS3172 25.10

HM3176 Tr 380 x 5 490 450 32 18 382.5 60 21 M 12 x 1.75 414 MS3176 30.90

HM3180 Tr 400 x 5 520 470 32 18 402.5 62 27 M 16 x 2 439 MS3180 36.90

HM3184 Tr 420 x 5 540 490 32 18 422.5 70 27 M 16 x 2 459 MS3184 43.50

HM3188 Tr 440 x 5 560 510 36 20 442.5 70 27 M 16 x 2 477 MS3188 45.30

HM3192 Tr 460 x 5 580 540 36 20 462.5 75 27 M 16 x 2 497 MS3192 50.40

HM3196 Tr 480 x 5 620 560 36 20 482.5 75 27 M 16 x 2 527 MS3196 62.20

HM31/500 Tr 500 x 5 630 580 40 23 502.5 80 27 M 16 x 2 539 MS31/500 63.30


(1)
Tr means 30; trapezoid thread and the digits are major diameter of thread and pitch.

112 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC LOCKWASHERS

METRIC LOCKWASHERS s 25

E u

D1
k D4 D5
t

Lockwasher(1) Thread No. of Weight per Locknut


k E t S D4 D5 r(2) u(2)
No. D1 Tangs 100 pieces No.

mm mm mm mm mm mm mm mm mm kg
MB0 10 8.5 3 1 3 13 21 0.5 2 9 0.13 KM00
MB1 12 10.5 3 1 3 17 25 0.5 2 9 0.19 KM01
MB2 15 13.5 4 1 4 21 28 1 2.5 13 0.25 KM02
MB3 17 15.5 4 1 4 24 32 1 2.5 13 0.31 KM03
MB4 20 18.5 4 1 4 26 36 1 2.5 13 0.35 KM04
MB5 25 23 5 1.2 5 32 42 1 2.5 13 0.64 KM05
MB6 30 27.5 5 1.2 5 38 49 1 2.5 13 0.78 KM06
MB7 35 32.5 6 1.2 5 44 57 1 2.5 15 1.04 KM07
MB8 40 37.5 6 1.2 6 50 62 1 2.5 15 1.23 KM08
MB9 45 42.5 6 1.2 6 56 69 1 2.5 17 1.52 KM09
MB10 50 47.5 6 1.2 6 61 74 1 2.5 17 1.60 KM10
MB11 55 52.5 8 1.2 7 67 81 1 4 17 1.96 KM11
MB12 60 57.5 8 1.5 7 73 86 1.2 4 17 2.53 KM12
MB13 65 62.5 8 1.5 7 79 92 1.2 4 19 2.90 KM13
MB14 70 66.5 8 1.5 8 85 98 1.2 4 19 3.34 KM14
MB15 75 71.5 8 1.5 8 90 104 1.2 4 19 3.56 KM15
MB16 80 76.5 10 1.8 8 95 112 1.2 4 19 4.64 KM16
MB17 85 81.5 10 1.8 8 102 119 1.2 4 19 5.24 KM17
MB18 90 86.5 10 1.8 10 108 126 1.2 4 19 6.23 KM18
MB19 95 91.5 10 1.8 10 113 133 1.2 4 19 6.70 KM19
MB20 100 96.5 12 1.8 10 120 142 1.2 6 19 7.65 KM20
MB21 105 100.5 12 1.8 12 126 145 1.2 6 19 8.26 KM21
MB22 110 105.5 12 1.8 12 133 154 1.2 6 19 9.40 KM22
MB23 115 110.5 12 2 12 137 159 1.5 6 19 10.80 KM23
MB24 120 115 14 2 12 138 164 1.5 6 19 10.50 KM24
MB25 125 120 14 2 12 148 170 1.5 6 19 11.80 KM25
MB26 130 125 14 2 12 149 175 1.5 6 19 11.30 KM26
MB27 135 130 14 2 14 160 185 1.5 6 19 14.40 KM27
MB28 140 135 16 2 14 160 192 1.5 8 19 14.20 KM28
MB29 145 140 16 2 14 171 202 1.5 8 19 16.80 KM29
(1)
No. MB0-MB40 also available in 304 stainless steel. Continued on next page.
(2)
Straight tangs when t 3 mm.

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 113
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC LOCKWASHERS

METRIC LOCKWASHERS continued s 25

E u

D1
k D4 D5
t

Continued from previous page.

Lockwasher(1) Thread No. of Weight per Locknut


k E t S D4 D5 r(2) u(2)
No. D1 Tangs 100 pieces No.

mm mm mm mm mm mm mm mm mm kg
MB30 150 145 16 2 14 171 205 1.5 8 19 15.50 KM30
MB31 155 147.5 16 2.5 16 182 212 1.5 8 19 20.90 KM31
MB32 160 154 18 2.5 18 182 217 1.5 8 19 22.20 KM32
MB33 165 157.5 18 2.5 16 193 222 1.5 8 19 24.10 KM33
MB34 170 164 18 2.5 16 193 232 1.5 8 19 24.70 KM34
MB36 180 174 20 2.5 18 203 242 1.5 8 19 26.80 KM36
MB38 190 184 20 2.5 18 214 252 1.5 8 19 27.80 KM38
MB40 200 194 20 2.5 18 226 262 1.5 8 19 29.30 KM40
MB44 220 213 24 3.0 20 250 292 19 48.30 HM3144
MB48 240 233 24 3.0 20 270 312 19 50.20 HM3148
MB52 260 253 28 3.0 24 300 342 23 72.90 HM3152
MB56 280 273 28 3.0 24 320 362 23 75.90 HM3156
(1)
No. MB0-MB40 also available in 304 stainless steel.
(2)
Straight tangs when t 3 mm.

114 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES
METRIC LOCKPLATES

METRIC LOCKPLATES S
t1

L3 i s1

t1

L2

Appropriate
Lockplate Weight per
t1 S L2 S1 i L3 Locknut
No. 100 pieces
No.

mm mm mm mm mm mm kg

MS3144 4 20 12 9 22.5 30.5 HM3144 2.60

MS3148 4 20 12 9 22.5 30.5 HM3148 2.60

MS3152 4 24 12 12 25.5 33.5 HM3152 3.39

MS3156 4 24 12 12 25.5 33.5 HM3156 3.39

MS3160 4 24 12 12 30.5 38.5 HM3160 3.79

MS3164 5 24 15 12 31 41 HM3164 5.35

MS3168 5 28 15 14 38 48 HM3168 6.65

MS3172 5 28 15 14 38 48 HM3172 6.65

MS3176 5 32 15 14 40 50 HM3176 7.96

MS3180 5 32 15 18 45 55 HM3180 8.20

MS3184 5 32 15 18 45 55 HM3184 8.20

MS3188 5 36 15 18 43 53 HM3188 9.00

MS3192 5 36 15 18 43 53 HM3192 9.00

MS3196 5 36 15 18 53 63 HM3196 10.40

MS31/500 5 40 15 18 45 55 HM31/500 10.50

MS3044 4 20 12 7 13.5 21.5 HM3044 2.12

MS3048 4 20 12 9 17.5 25.5 HM3048 2.29

MS3052 4 20 12 9 17.5 25.5 HM3052 2.29

MS3056 4 24 12 9 17.5 25.5 HM3056 2.92

MS3060 4 24 12 9 20.5 28.5 HM3060 3.16

MS3064 5 24 15 9 21 31 HM3064 4.56

MS3068 5 24 15 9 21 31 HM3068 4.56

MS3072 5 28 15 9 20 30 HM3072 5.03

MS3076 5 28 15 12 24 34 HM3076 5.28

MS3080 5 28 15 12 24 34 HM3080 5.28

MS3084 5 32 15 12 24 34 HM3084 6.11

MS3088 5 32 15 14 28 38 HM3088 6.45

MS3092 5 32 15 14 28 38 HM3092 6.45

MS3096 5 36 15 14 28 38 HM3096 7.29

MS30/500 5 36 15 14 28 38 HM30/500 7.29

TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com 115
SNT SPHERICAL ROLLER BEARING METRIC ACCESSORIES

INDEX
TIMKEN SNT PLUMMER BLOCKS
213 Series Spherical Roller Bearings
(200, 300, 500, 600 Series SNT, FSNT) ................................................. 85
222 Series Spherical Roller Bearings
(200, 500 Series SNT, FSNT) ................................................................. 86
223 Series Spherical Roller Bearings
(500, 600 Series SNT, FSNT) ................................................................. 88
230 Series Spherical Roller Bearings
(3000 Series SNT, FSNT) ....................................................................... 89
231 Series Spherical Roller Bearings
(300, 3100 Series SNT, FSNT) ............................................................... 90
232 Series Spherical Roller Bearings
(500, 600 Series SNT, FSNT) ................................................................. 91
Engineering ............................................................................................. 17
Four-Bolt FSNT Housings for Cylindrical Bore Bearings ................ 74
Four-Bolt FSNT Housings for Tapered Bore Bearings ..................... 66
Installation Guides ................................................................................. 55
Large Plummer Block Housings 3000 and 3100 Series ................. 78
Metric Accessories Index .................................................................... 96
Metric H Adapter Sleeves .................................................................. 100
Metric Locknuts ................................................................................... 108
Metric Lockwashers............................................................................ 113
Metric Lockplates ................................................................................ 115
Metric OH Hydraulic Adapter Sleeves ............................................. 104
Metric Shaft Diameters......................................................................... 82
SNT Spherical Roller Bearings Metric Accessories ....................... 93
SNT Spherical Roller Bearing Plummer Block Introduction .......... 51
Timken SNT Plummer Blocks............................................................... 1
Two-Bolt SNT Housings for Cylindrical Bore Bearings ................... 70
Two-Bolt SNT Housings for Tapered Bore Bearings ....................... 60

116 TIMKEN SNT PLUMMER BLOCK CATALOG Download 3D Models and 2D Drawings at cad.timken.com
08-13 Order No. 10624 | Timken is a registered trademark of The Timken Company. | 2013 The Timken Company | Printed in U.S.A.

The Timken team applies their know-how to improve the reliability and performance of machinery in diverse www.timken.com
markets worldwide. The company designs, makes and markets high-performance steel as well as mechanical
components, including bearings, gears, chain and related mechanical power transmission products and services.

Price: USD $75

You might also like