Swacl

CH A P T E R 36
Configuring Network Security with ACLs
This chapter describes how to configure network security on the Catalyst 3750-X or 3560-X switch by
using access control lists (ACLs), which in commands and tables are also referred to as access
lists.Unless otherwise noted, the term switch refers to a Catalyst 3750-X or 3560-X standalone switch
and to a Catalyst 3750-X switch stack.
Note Information in this chapter about IP ACLs is specific to IP Version 4 (IPv4). For information about IPv6
ACLs, see Chapter 38, Configuring IPv6 ACLs.
For complete syntax and usage information for the commands used in this chapter, see the command
reference for this release, see the Configuring IP Services section in the IP Addressing and Services
chapter of the Cisco IOS IP Configuration Guide, Release 12.4, and the Cisco IOS IP Command
Reference, Volume 1 of 3: Addressing and Services, Release 12.4.
Catalyst 3750-X and 3560-X switches running the IP base or IP services feature set also support Cisco
TrustSec Security Group Tag (SCT) Exchange Protocol (SXP). This feature supports security group
access control lists (SGACLs), which define ACL policies for a group of devices instead of an IP
address. The SXP control protocol allows tagging packets with SCTs without a hardware upgrade, and
runs between access layer devices at the Cisco TrustSec domain edge and distribution layer devices
within the Cisco TrustSec domain. Catalyst 3750-X and 3560-X switches operate as access layer
switches in the Cisco TrustSec network.
For more information about Cisco TrustSec, see the Cisco TrustSec Switch Configuration Guide at this
URL:
http://www.cisco.com/en/US/docs/switches/lan/trustsec/configuration/guide/trustsec.html
The sections on SXP define the capabilities supported on the Catalyst 3750-X and 3560-X switches.
Note On switches running the LAN base feature set, router ACLs are supported only on switch virtual
interfaces (SVIs). VLAN maps are not supported.
This chapter consists of these sections:

Understanding ACLs, page 36-2
Configuring IPv4 ACLs, page 36-7
Creating Named MAC Extended ACLs, page 36-29
Configuring VLAN Maps, page 36-32
Catalyst 3750-X and 3560-X Switch Software Configuration Guide

OL-21521-03 36-1
Chapter 36 Configuring Network Security with ACLs
Understanding ACLs
Using VLAN Maps with Router ACLs, page 36-40

Displaying IPv4 ACL Configuration, page 36-44
Understanding ACLs
Packet filtering can help limit network traffic and restrict network use by certain users or devices. ACLs
filter traffic as it passes through a router or switch and permit or deny packets crossing specified
interfaces or VLANs. An ACL is a sequential collection of permit and deny conditions that apply to
packets. When a packet is received on an interface, the switch compares the fields in the packet against
any applied ACLs to verify that the packet has the required permissions to be forwarded, based on the
criteria specified in the access lists. One by one, it tests packets against the conditions in an access list.
The first match decides whether the switch accepts or rejects the packets. Because the switch stops
testing after the first match, the order of conditions in the list is critical. If no conditions match, the
switch rejects the packet. If there are no restrictions, the switch forwards the packet; otherwise, the
switch drops the packet. The switch can use ACLs on all packets it forwards, including packets bridged
within a VLAN.
You configure access lists on a router or Layer 3 switch to provide basic security for your network. If
you do not configure ACLs, all packets passing through the switch could be allowed onto all parts of the
network. You can use ACLs to control which hosts can access different parts of a network or to decide
which types of traffic are forwarded or blocked at router interfaces. For example, you can allow e-mail
traffic to be forwarded but not Telnet traffic. ACLs can be configured to block inbound traffic, outbound
traffic, or both.
An ACL contains an ordered list of access control entries (ACEs). Each ACE specifies permit or deny
and a set of conditions the packet must satisfy in order to match the ACE. The meaning of permit or deny
depends on the context in which the ACL is used.
The switch supports IP ACLs and Ethernet (MAC) ACLs:
IP ACLs filter IPv4 traffic, including TCP, User Datagram Protocol (UDP), Internet Group
Management Protocol (IGMP), and Internet Control Message Protocol (ICMP).
Ethernet ACLs filter non-IP traffic.
This switch also supports quality of service (QoS) classification ACLs. For more information, see the
Classification Based on QoS ACLs section on page 37-7.
These sections contain this conceptual information:
Supported ACLs, page 36-2
Handling Fragmented and Unfragmented Traffic, page 36-6
ACLs and Switch Stacks, page 36-7
Supported ACLs
The switch supports three types of ACLs to filter traffic:
Note On switches running the LAN base feature set, router ACLs are supported only on SVIs and VLAN maps
are not supported.

36-2 OL-21521-03
Understanding ACLs
Port ACLs access-control traffic entering a Layer 2 interface. The switch does not support port ACLs
in the outbound direction. You can apply only one IP access list and one MAC access list to a Layer 2
interface. For more information, see the Port ACLs section on page 36-4.
Router ACLs access-control routed traffic between VLANs and are applied to Layer 3 interfaces in
a specific direction (inbound or outbound). For more information, see the Router ACLs section on
page 36-5.
VLAN ACLs or VLAN maps access-control all packets (bridged and routed). You can use VLAN
maps to filter traffic between devices in the same VLAN. VLAN maps are configured to provide
access control based on Layer 3 addresses for IPv4. Unsupported protocols are access-controlled
through MAC addresses using Ethernet ACEs. After a VLAN map is applied to a VLAN, all packets
(routed or bridged) entering the VLAN are checked against the VLAN map. Packets can either enter
the VLAN through a switch port or through a routed port after being routed. For more information,
see the VLAN Maps section on page 36-5.
You can use input port ACLs, router ACLs, and VLAN maps on the same switch. However, a port ACL
takes precedence over a router ACL or VLAN map.
When both an input port ACL and a VLAN map are applied, incoming packets received on ports
with a port ACL applied are filtered by the port ACL. Other packets are filtered by the VLAN map
When an input router ACL and input port ACL exist in an switch virtual interface (SVI), incoming
packets received on ports to which a port ACL is applied are filtered by the port ACL. Incoming
routed IP packets received on other ports are filtered by the router ACL. Other packets are not
filtered.
When an output router ACL and input port ACL exist in an SVI, incoming packets received on the
ports to which a port ACL is applied are filtered by the port ACL. Outgoing routed IP packets are
filtered by the router ACL. Other packets are not filtered.
When a VLAN map, input router ACL, and input port ACL exist in an SVI, incoming packets
received on the ports to which a port ACL is applied are only filtered by the port ACL. Incoming
routed IP packets received on other ports are filtered by both the VLAN map and the router ACL.
Other packets are filtered only by the VLAN map.
When a VLAN map, output router ACL, and input port ACL exist in an SVI, incoming packets
received on the ports to which a port ACL is applied are only filtered by the port ACL. Outgoing
routed IP packets are filtered by both the VLAN map and the router ACL. Other packets are filtered
only by the VLAN map.
If IEEE 802.1Q tunneling is configured on an interface, any IEEE 802.1Q encapsulated IP packets
received on the tunnel port can be filtered by MAC ACLs, but not by IP ACLs. This is because the switch
does not recognize the protocol inside the IEEE 802.1Q header. This restriction applies to router ACLs,
port ACLs, and VLAN maps. For more information about IEEE 802.1Q tunneling, see Chapter 18,
Configuring IEEE 802.1Q Tunneling and Chapter 18, Configuring Layer 2 Protocol Tunneling.

OL-21521-03 36-3
Understanding ACLs
Port ACLs
Port ACLs are ACLs that are applied to Layer 2 interfaces on a switch. Port ACLs are supported only on
physical interfaces and not on EtherChannel interfaces and can be applied only on interfaces in the
inbound direction. These access lists are supported:
Standard IP access lists using source addresses
Extended IP access lists using source and destination addresses and optional protocol type
information
MAC extended access lists using source and destination MAC addresses and optional protocol type
information
The switch examines ACLs associated with all inbound features configured on a given interface and
permits or denies packet forwarding based on how the packet matches the entries in the ACL. In this way,
ACLs control access to a network or to part of a network. Figure 36-1 is an example of using port ACLs
to control access to a network when all workstations are in the same VLAN. ACLs applied at the Layer 2
input would allow Host A to access the Human Resources network, but prevent Host B from accessing
the same network. Port ACLs can only be applied to Layer 2 interfaces in the inbound direction.
Figure 36-1 Using ACLs to Control Traffic to a Network
Host A
Host B
Human Research &

Resources Development
network network
= ACL denying traffic from Host B

101365
and permitting traffic from Host A

= Packet
When you apply a port ACL to a trunk port, the ACL filters traffic on all VLANs present on the trunk
port. When you apply a port ACL to a port with voice VLAN, the ACL filters traffic on both data and
voice VLANs.
With port ACLs, you can filter IP traffic by using IP access lists and non-IP traffic by using MAC
addresses. You can filter both IP and non-IP traffic on the same Layer 2 interface by applying both an IP
access list and a MAC access list to the interface.

36-4 OL-21521-03
Understanding ACLs
Note You cannot apply more than one IP access list and one MAC access list to a Layer 2 interface. If an IP
access list or MAC access list is already configured on a Layer 2 interface and you apply a new IP access
list or MAC access list to the interface, the new ACL replaces the previously configured one.
Router ACLs
Note On switches running the LAN base feature set, router ACLs are supported only on SVIs.
You can apply router ACLs on switch virtual interfaces (SVIs), which are Layer 3 interfaces to VLANs;
on physical Layer 3 interfaces; and on Layer 3 EtherChannel interfaces. You apply router ACLs on
interfaces for specific directions (inbound or outbound). You can apply one router ACL in each direction
on an interface.
One ACL can be used with multiple features for a given interface, and one feature can use multiple
ACLs. When a single router ACL is used by multiple features, it is examined multiple times.
The switch supports these access lists for IPv4 traffic:
Standard IP access lists use source addresses for matching operations.
Extended IP access lists use source and destination addresses and optional protocol type information
for matching operations.
As with port ACLs, the switch examines ACLs associated with features configured on a given interface.
However, router ACLs are supported in both directions. As packets enter the switch on an interface,
ACLs associated with all inbound features configured on that interface are examined. After packets are
routed and before they are forwarded to the next hop, all ACLs associated with outbound features
configured on the egress interface are examined.
ACLs permit or deny packet forwarding based on how the packet matches the entries in the ACL, and
can be used to control access to a network or to part of a network. In Figure 36-1, ACLs applied at the
router input allow Host A to access the Human Resources network, but prevent Host B from accessing
the same network.
VLAN Maps
Note VLAN maps are not supported on switches running the LAN base feature set.
Use VLAN ACLs or VLAN maps to access-control all traffic. You can apply VLAN maps to all packets
that are routed into or out of a VLAN or are bridged within a VLAN in the switch or switch stack.
Use VLAN maps for security packet filtering. VLAN maps are not defined by direction (input or output).
You can configure VLAN maps to match Layer 3 addresses for IPv4 traffic.
All non-IP protocols are access-controlled through MAC addresses and Ethertype using MAC VLAN
maps. (IP traffic is not access controlled by MAC VLAN maps.) You can enforce VLAN maps only on
packets going through the switch; you cannot enforce VLAN maps on traffic between hosts on a hub or
on another switch connected to this switch.

OL-21521-03 36-5
Understanding ACLs
With VLAN maps, forwarding of packets is permitted or denied, based on the action specified in the
map. Figure 36-2 shows how a VLAN map is applied to prevent a specific type of traffic from Host A in
VLAN 10 from being forwarded. You can apply only one VLAN map to a VLAN.
Figure 36-2 Using VLAN Maps to Control Traffic
Host A Host B
(VLAN 10) (VLAN 10)
= VLAN map denying specific type
92919
of traffic from Host A
= Packet
Handling Fragmented and Unfragmented Traffic

IP packets can be fragmented as they cross the network. When this happens, only the fragment
containing the beginning of the packet contains the Layer 4 information, such as TCP or UDP port
numbers, ICMP type and code, and so on. All other fragments are missing this information.
Some ACEs do not check Layer 4 information and therefore can be applied to all packet fragments. ACEs
that do test Layer 4 information cannot be applied in the standard manner to most of the fragments in a
fragmented IP packet. When the fragment contains no Layer 4 information and the ACE tests some
Layer 4 information, the matching rules are modified:
Permit ACEs that check the Layer 3 information in the fragment (including protocol type, such as
TCP, UDP, and so on) are considered to match the fragment regardless of what the missing Layer 4
information might have been.
Deny ACEs that check Layer 4 information never match a fragment unless the fragment contains
Layer 4 information.
Consider access list 102, configured with these commands, applied to three fragmented packets:
Switch(config)# access-list 102 permit tcp any host 10.1.1.1 eq smtp
Switch(config)# access-list 102 deny tcp any host 10.1.1.2 eq telnet
Switch(config)# access-list 102 permit tcp any host 10.1.1.2
Switch(config)# access-list 102 deny tcp any any
Note In the first and second ACEs in the examples, the eq keyword after the destination address means to test
for the TCP-destination-port well-known numbers equaling Simple Mail Transfer Protocol (SMTP) and
Telnet, respectively.
Packet A is a TCP packet from host 10.2.2.2., port 65000, going to host 10.1.1.1 on the SMTP port.
If this packet is fragmented, the first fragment matches the first ACE (a permit) as if it were a
complete packet because all Layer 4 information is present. The remaining fragments also match the
first ACE, even though they do not contain the SMTP port information, because the first ACE only
checks Layer 3 information when applied to fragments. The information in this example is that the
packet is TCP and that the destination is 10.1.1.1.

36-6 OL-21521-03
Configuring IPv4 ACLs
Packet B is from host 10.2.2.2, port 65001, going to host 10.1.1.2 on the Telnet port. If this packet
is fragmented, the first fragment matches the second ACE (a deny) because all Layer 3 and Layer 4
information is present. The remaining fragments in the packet do not match the second ACE because
they are missing Layer 4 information. Instead, they match the third ACE (a permit).
Because the first fragment was denied, host 10.1.1.2 cannot reassemble a complete packet, so packet
B is effectively denied. However, the later fragments that are permitted will consume bandwidth on
the network and resources of host 10.1.1.2 as it tries to reassemble the packet.
Fragmented packet C is from host 10.2.2.2, port 65001, going to host 10.1.1.3, port ftp. If this packet
is fragmented, the first fragment matches the fourth ACE (a deny). All other fragments also match
the fourth ACE because that ACE does not check any Layer 4 information and because Layer 3
information in all fragments shows that they are being sent to host 10.1.1.3, and the earlier permit
ACEs were checking different hosts.
ACLs and Switch Stacks

ACL support is the same for a switch stack as for a standalone switch. ACL configuration information
is propagated to all switches in the stack. All switches in the stack, including the stack master, process
the information and program their hardware. (For more information about switch stacks, see Chapter 5,
Configuring the Switch Stack.)
The stack master performs these ACL functions:
It processes the ACL configuration and propagates the information to all stack members.
It distributes the ACL information to any switch that joins the stack.
If packets must be forwarded by software for any reason (for example, not enough hardware
resources), the master switch forwards the packets only after applying ACLs on the packets.
It programs its hardware with the ACL information it processes.
Stack members perform these ACL functions:
They receive the ACL information from the master switch and program their hardware.
They act as standby switches, ready to take over the role of the stack master if the existing master
were to fail and they were to be elected as the new stack master.
When a stack master fails and a new stack master is elected, the newly elected master reparses the backed
up running configuration. (See Chapter 5, Configuring the Switch Stack.) The ACL configuration that
is part of the running configuration is also reparsed during this step. The new stack master distributes
the ACL information to all switches in the stack.

Configuring IP v4ACLs on the switch is the same as configuring IPv4 ACLs on other Cisco switches and
routers. The process is briefly described here. For more detailed information on configuring ACLs, see
the Configuring IP Services section in the IP Addressing and Services chapter of the Cisco IOS IP
Configuration Guide, Release 12.4. For detailed information about the commands, see the Cisco IOS IP
Command Reference, Volume 1 of 3: Addressing and Services, Release 12.4.
The switch does not support these Cisco IOS router ACL-related features:
Non-IP protocol ACLs (see Table 36-1 on page 36-9) or bridge-group ACLs
IP accounting

OL-21521-03 36-7
Inbound and outbound rate limiting (except with QoS ACLs)

Reflexive ACLs or dynamic ACLs (except for some specialized dynamic ACLs used by the switch
clustering feature)
ACL logging for port ACLs and VLAN maps
These are the steps to use IP ACLs on the switch:
Step 1 Create an ACL by specifying an access list number or name and the access conditions.
Step 2 Apply the ACL to interfaces or terminal lines. You can also apply standard and extended IP ACLs to
VLAN maps.
These sections contain this configuration information:

Creating Standard and Extended IPv4 ACLs, page 36-8
Applying an IPv4 ACL to a Terminal Line, page 36-20
Applying an IPv4 ACL to an Interface, page 36-21
Hardware and Software Treatment of IP ACLs, page 36-23
Troubleshooting ACLs, page 36-23
IPv4 ACL Configuration Examples, page 36-24
Creating Standard and Extended IPv4 ACLs

This section describes IP ACLs. An ACL is a sequential collection of permit and deny conditions. One
by one, the switch tests packets against the conditions in an access list. The first match determines
whether the switch accepts or rejects the packet. Because the switch stops testing after the first match,
the order of the conditions is critical. If no conditions match, the switch denies the packet.
The software supports these types of ACLs or access lists for IPv4:
Standard IP access lists use source addresses for matching operations.
Extended IP access lists use source and destination addresses for matching operations and optional
protocol-type information for finer granularity of control.
These sections describe access lists and how to create them:
Access List Numbers, page 36-9
ACL Logging, page 36-9
Smart Logging, page 36-10
Creating a Numbered Standard ACL, page 36-10
Creating a Numbered Extended ACL, page 36-11
Resequencing ACEs in an ACL, page 36-16
Creating Named Standard and Extended ACLs, page 36-16
Using Time Ranges with ACLs, page 36-18
Including Comments in ACLs, page 36-20

36-8 OL-21521-03
Access List Numbers

The number you use to denote your ACL shows the type of access list that you are creating. Table 36-1
lists the access-list number and corresponding access list type and shows whether or not they are
supported in the switch. The switch supports IPv4 standard and extended access lists, numbers 1 to 199
and 1300 to 2699.
Table 36-1 Access List Numbers
Access List Number Type Supported

199 IP standard access list Yes
100199 IP extended access list Yes
200299 Protocol type-code access list No
300399 DECnet access list No
400499 XNS standard access list No
500599 XNS extended access list No
600699 AppleTalk access list No
700799 48-bit MAC address access list No
800899 IPX standard access list No
900999 IPX extended access list No
10001099 IPX SAP access list No
11001199 Extended 48-bit MAC address access list No
12001299 IPX summary address access list No
13001999 IP standard access list (expanded range) Yes
20002699 IP extended access list (expanded range) Yes
Note In addition to numbered standard and extended ACLs, you can also create standard and extended named
IP ACLs by using the supported numbers. That is, the name of a standard IP ACL can be 1 to 99; the
name of an extended IP ACL can be 100 to 199. The advantage of using named ACLs instead of
numbered lists is that you can delete individual entries from a named list.
ACL Logging
The switch software can provide logging messages about packets permitted or denied by a standard IP
access list. That is, any packet that matches the ACL causes an informational logging message about the
packet to be sent to the console. The level of messages logged to the console is controlled by the logging
console commands controlling the syslog messages.
Note Because routing is done in hardware and logging is done in software, if a large number of packets match
a permit or deny ACE containing a log keyword, the software might not be able to match the hardware
processing rate, and not all packets will be logged.

OL-21521-03 36-9
The first packet that triggers the ACL causes a logging message right away, and subsequent packets are
collected over 5-minute intervals before they appear or logged. The logging message includes the access
list number, whether the packet was permitted or denied, the source IP address of the packet, and the
number of packets from that source permitted or denied in the prior 5-minute interval.
Smart Logging
When smart logging is enabled on the switch and an ACL configured with smart logging is attached to
a Layer 2 interface (port ACL), the contents of packets denied or permitted because of the ACL are also
sent to a specified NetFlow collector. For more information about smart logging, see the Configuring
Smart Logging section on page 33-14.
Creating a Numbered Standard ACL

Beginning in privileged EXEC mode, follow these steps to create a numbered standard ACL:
Command Purpose
Step 1 configure terminal Enter global configuration mode.
Step 2 access-list access-list-number {deny | permit} Define a standard IPv4 access list by using a source address and
source [source-wildcard] [log | smartlog] wildcard.
The access-list-number is a decimal number from 1 to 99 or 1300
to 1999.
Enter deny or permit to specify whether to deny or permit access
if conditions are matched.
The source is the source address of the network or host from which
the packet is being sent specified as:
The 32-bit quantity in dotted-decimal format.
The keyword any as an abbreviation for source and
source-wildcard of 0.0.0.0 255.255.255.255. You do not need
to enter a source-wildcard.
The keyword host as an abbreviation for source and
source-wildcard of source 0.0.0.0.
(Optional) The source-wildcard applies wildcard bits to the
source.
(Optional) Enter log to cause an informational logging message
about the packet that matches the entry to be sent to the console.
(Optional) Enter smartlog to send copies of denied or permitted
packets to a NetFlow collector.
Note Logging is supported only on ACLs attached to Layer 3
interfaces. Smart logging is supported only on ACLs
attached to Layer 2 interfaces.
Step 3 end Return to privileged EXEC mode.
Step 4 show access-lists [number | name] Show the access list configuration.
Step 5 copy running-config startup-config (Optional) Save your entries in the configuration file.

36-10 OL-21521-03
Use the no access-list access-list-number global configuration command to delete the entire ACL. You
cannot delete individual ACEs from numbered access lists.
Note When creating an ACL, remember that, by default, the end of the ACL contains an implicit deny
statement for all packets that it did not find a match for before reaching the end. With standard access
lists, if you omit the mask from an associated IP host address ACL specification, 0.0.0.0 is assumed to
be the mask.
This example shows how to create a standard ACL to deny access to IP host 171.69.198.102, permit
access to any others, and display the results.
Switch (config)# access-list 2 deny host 171.69.198.102
Switch (config)# access-list 2 permit any
Switch(config)# end
Switch# show access-lists
Standard IP access list 2
10 deny 171.69.198.102
20 permit any
The switch always rewrites the order of standard access lists so that entries with host matches and entries
with matches having a dont care mask of 0.0.0.0 are moved to the top of the list, above any entries with
non-zero dont care masks. Therefore, in show command output and in the configuration file, the ACEs
do not necessarily appear in the order in which they were entered.
After creating a numbered standard IPv4 ACL, you can apply it to terminal lines (see the Applying an
IPv4 ACL to a Terminal Line section on page 36-20), to interfaces (see the Applying an IPv4 ACL to
an Interface section on page 36-21), or to VLANs (see the Configuring VLAN Maps section on
page 36-32).
Creating a Numbered Extended ACL

Although standard ACLs use only source addresses for matching, you can use extended ACL source and
destination addresses for matching operations and optional protocol type information for finer
granularity of control. When you are creating ACEs in numbered extended access lists, remember that
after you create the ACL, any additions are placed at the end of the list. You cannot reorder the list or
selectively add or remove ACEs from a numbered list.
Some protocols also have specific parameters and keywords that apply to that protocol.
These IP protocols are supported (protocol keywords are in parentheses in bold):
Authentication Header Protocol (ahp), Enhanced Interior Gateway Routing Protocol (eigrp),
Encapsulation Security Payload (esp), generic routing encapsulation (gre), Internet Control Message
Protocol (icmp), Internet Group Management Protocol (igmp), any Interior Protocol (ip), IP in IP
tunneling (ipinip), KA9Q NOS-compatible IP over IP tunneling (nos), Open Shortest Path First routing
(ospf), Payload Compression Protocol (pcp), Protocol-Independent Multicast (pim), Transmission
Control Protocol (tcp), or User Datagram Protocol (udp).
Note ICMP echo-reply cannot be filtered. All other ICMP codes or types can be filtered.

OL-21521-03 36-11
For more details on the specific keywords for each protocol, see these command references:
Cisco IOS IP Command Reference, Volume 1 of 3: Addressing and Services, Release 12.4
Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols, Release 12.4
Cisco IOS IP Command Reference, Volume 3 of 3: Multicast, Release 12.4
Note The switch does not support dynamic or reflexive access lists. It also does not support filtering based on
the type of service (ToS) minimize-monetary-cost bit.
Supported parameters can be grouped into these categories: TCP, UDP, ICMP, IGMP, or other IP.

36-12 OL-21521-03
Beginning in privileged EXEC mode, follow these steps to create an extended ACL:
Command Purpose
Step 2a access-list access-list-number Define an extended IPv4 access list and the access conditions.
{deny | permit} protocol The access-list-number is a decimal number from 100 to 199 or 2000 to 2699.
source source-wildcard
destination destination-wildcard Enter deny or permit to specify whether to deny or permit the packet if
[precedence precedence] [tos tos] conditions are matched.
[fragments] [log [log-input] | For protocol, enter the name or number of an P protocol: ahp, eigrp, esp, gre,
smartlog] [time-range icmp, igmp, igrp, ip, ipinip, nos, ospf, pcp, pim, tcp, or udp, or an integer in
time-range-name] [dscp dscp] the range 0 to 255 representing an IP protocol number. To match any Internet
Note If you enter a dscp value, protocol (including ICMP, TCP, and UDP), use the keyword ip.
you cannot enter tos or Note This step includes options for most IP protocols. For additional specific
precedence. You can enter parameters for TCP, UDP, ICMP, and IGMP, see steps 2b through 2e.
both a tos and a
precedence value with no The source is the number of the network or host from which the packet is sent.
dscp.
The source-wildcard applies wildcard bits to the source.
The destination is the network or host number to which the packet is sent.
The destination-wildcard applies wildcard bits to the destination.
Source, source-wildcard, destination, and destination-wildcard can be specified
as:
The 32-bit quantity in dotted-decimal format.
The keyword any for 0.0.0.0 255.255.255.255 (any host).
The keyword host for a single host 0.0.0.0.
The other keywords are optional and have these meanings:
precedenceEnter to match packets with a precedence level specified as a
number from 0 to 7 or by name: routine (0), priority (1), immediate (2),
flash (3), flash-override (4), critical (5), internet (6), network (7).
fragmentsEnter to check non-initial fragments.
tosEnter to match by type of service level, specified by a number from 0
to 15 or a name: normal (0), max-reliability (2), max-throughput (4),
min-delay (8).
logEnter to create an informational logging message to be sent to the
console about the packet that matches the entry or log-input to include the
input interface in the log entry.
smartlogEnter when smart logging is globally enabled to have a copy of
the denied or permitted packet sent to a NetFlow collector.
time-rangeFor an explanation of this keyword, see the Using Time
Ranges with ACLs section on page 36-18.
dscpEnter to match packets with the DSCP value specified by a number
from 0 to 63, or use the question mark (?) to see a list of available values.

OL-21521-03 36-13
Command Purpose
or access-list access-list-number In access-list configuration mode, define an extended IP access list using an
{deny | permit} protocol any any abbreviation for a source and source wildcard of 0.0.0.0 255.255.255.255 and
[precedence precedence] [tos tos] an abbreviation for a destination and destination wildcard of 0.0.0.0
[fragments] [log [log-input] | 255.255.255.255.
smartlog] [time-range You can use the any keyword in place of source and destination address and
time-range-name] [dscp dscp] wildcard.
or access-list access-list-number Define an extended IP access list by using an abbreviation for a source and a
{deny | permit} protocol source wildcard of source 0.0.0.0 and an abbreviation for a destination and
host source host destination destination wildcard of destination 0.0.0.0.
[precedence precedence] [tos tos] You can use the host keyword in place of the source and destination wildcard
[fragments] [log [log-input] | or mask.
smartlog] [time-range
time-range-name] [dscp dscp]
Step 2b access-list access-list-number (Optional) Define an extended TCP access list and the access conditions.
{deny | permit} tcp source Enter tcp for Transmission Control Protocol.
source-wildcard [operator port]
destination destination-wildcard The parameters are the same as those described in Step 2a, with these
[operator port] [established] exceptions:
[precedence precedence] [tos tos] (Optional) Enter an operator and port to compare source (if positioned after
[fragments] [log [log-input] | source source-wildcard) or destination (if positioned after destination
smartlog] [time-range destination-wildcard) port. Possible operators include eq (equal), gt (greater
time-range-name] [dscp dscp] than), lt (less than), neq (not equal), and range (inclusive range). Operators
[flag] require a port number (range requires two port numbers separated by a space).
Enter the port number as a decimal number (from 0 to 65535) or the name of a
TCP port. To see TCP port names, use the ? or see the Configuring IP Services
section in the IP Addressing and Services chapter of the Cisco IOS IP
Configuration Guide, Release 12.4. Use only TCP port numbers or names when
filtering TCP.
The other optional keywords have these meanings:
establishedEnter to match an established connection. This has the same
function as matching on the ack or rst flag.
flagEnter one of these flags to match by the specified TCP header bits:
ack (acknowledge), fin (finish), psh (push), rst (reset), syn (synchronize),
or urg (urgent).
Step 2c access-list access-list-number (Optional) Define an extended UDP access list and the access conditions.
{deny | permit} udp Enter udp for the User Datagram Protocol.
source source-wildcard [operator
port] destination The UDP parameters are the same as those described for TCP except that the
destination-wildcard [operator [operator [port]] port number or name must be a UDP port number or name, and
port] [precedence precedence] the flag and established parameters are not valid for UDP.
[tos tos] [fragments] [log
[log-input] | smartlog]
[time-range time-range-name]
[dscp dscp]

36-14 OL-21521-03
Command Purpose
Step 2d access-list access-list-number (Optional) Define an extended ICMP access list and the access conditions.
{deny | permit} icmp source Enter icmp for Internet Control Message Protocol.
source-wildcard destination
destination-wildcard [icmp-type | The ICMP parameters are the same as those described for most IP protocols in
[[icmp-type icmp-code] | Step 2a, with the addition of the ICMP message type and code parameters.
[icmp-message]] [precedence These optional keywords have these meanings:
precedence] [tos tos] [fragments] icmp-typeEnter to filter by ICMP message type, a number from 0 to 255.
[log [log-input] | smartlog]
[time-range time-range-name] icmp-codeEnter to filter ICMP packets that are filtered by the ICMP
[dscp dscp] message code type, a number from 0 to 255.
icmp-messageEnter to filter ICMP packets by the ICMP message type
name or the ICMP message type and code name. To see a list of ICMP
message type names and code names, use the ?, or see the Configuring IP
Services section of the Cisco IOS IP Configuration Guide, Release 12.4.
Step 2e access-list access-list-number (Optional) Define an extended IGMP access list and the access conditions.
{deny | permit} igmp source
Enter igmp for Internet Group Management Protocol.
source-wildcard destination
destination-wildcard [igmp-type] The IGMP parameters are the same as those described for most IP protocols in
[precedence precedence] [tos tos] Step 2a, with this optional parameter.
[fragments] [log [log-input] | igmp-typeTo match IGMP message type, enter a number from 0 to 15, or enter
smartlog] [time-range the message name (dvmrp, host-query, host-report, pim, or trace).
time-range-name] [dscp dscp]
Step 4 show access-lists [number | name] Verify the access list configuration.
Step 5 copy running-config (Optional) Save your entries in the configuration file.
startup-config
Use the no access-list access-list-number global configuration command to delete the entire access list.
You cannot delete individual ACEs from numbered access lists.
This example shows how to create and display an extended access list to deny Telnet access from any
host in network 171.69.198.0 to any host in network 172.20.52.0 and to permit any others. (The eq
keyword after the destination address means to test for the TCP destination port number equaling
Telnet.)
Switch(config)# access-list 102 deny tcp 171.69.198.0 0.0.0.255 172.20.52.0 0.0.0.255 eq
telnet
Switch(config)# access-list 102 permit tcp any any
Switch(config)# end
Extended IP access list 102
10 deny tcp 171.69.198.0 0.0.0.255 172.20.52.0 0.0.0.255 eq telnet
20 permit tcp any any
After an ACL is created, any additions (possibly entered from the terminal) are placed at the end of the
list. You cannot selectively add or remove access list entries from a numbered access list.
Note When you are creating an ACL, remember that, by default, the end of the access list contains an implicit
deny statement for all packets if it did not find a match before reaching the end.

OL-21521-03 36-15
After creating a numbered extended ACL, you can apply it to terminal lines (see the Applying an IPv4
ACL to a Terminal Line section on page 36-20), to interfaces (see the Applying an IPv4 ACL to an
Interface section on page 36-21), or to VLANs (see the Configuring VLAN Maps section on
page 36-32).
Resequencing ACEs in an ACL

Sequence numbers for the entries in an access list are automatically generated when you create a new
ACL. You can use the ip access-list resequence global configuration command to edit the sequence
numbers in an ACL and change the order in which ACEs are applied. For example, if you add a new ACE
to an ACL, it is placed at the bottom of the list. By changing the sequence number, you can move the
ACE to a different position in the ACL.
Creating Named Standard and Extended ACLs

You can identify IPv4 ACLs with an alphanumeric string (a name) rather than a number. You can use
named ACLs to configure more IPv4 access lists in a router than if you were to use numbered access
lists. If you identify your access list with a name rather than a number, the mode and command syntax
are slightly different. However, not all commands that use IP access lists accept a named access list.
Note The name you give to a standard or extended ACL can also be a number in the supported range of access
list numbers. That is, the name of a standard IP ACL can be 1 to 99; the name of an extended IP ACL
can be 100 to 199. The advantage of using named ACLs instead of numbered lists is that you can delete
individual entries from a named list.
Consider these guidelines and limitations before configuring named ACLs:

Not all commands that accept a numbered ACL accept a named ACL. ACLs for packet filters and
route filters on interfaces can use a name. VLAN maps also accept a name.
A standard ACL and an extended ACL cannot have the same name.
Numbered ACLs are also available, as described in the Creating Standard and Extended IPv4
ACLs section on page 36-8.
You can use standard and extended ACLs (named or numbered) in VLAN maps.
With IPv4 QoS ACLs, if you enter the class-map {match-all | match-any} class-map-name global
configuration command, you can enter these match commands:
match access-group acl-name
Note The ACL must be an extended named ACL.
match input-interface interface-id-list

match ip dscp dscp-list
match ip precedence ip-precedence-list
You cannot enter the match access-group acl-index command.

36-16 OL-21521-03
Beginning in privileged EXEC mode, follow these steps to create a standard ACL using names:
Command Purpose
Step 2 ip access-list standard name Define a standard IPv4 access list using a name, and enter
access-list configuration mode.
The name can be a number from 1 to 99.
Step 3 deny {source [source-wildcard] | host source | In access-list configuration mode, specify one or more conditions
any} [log | smartlog] denied or permitted to decide if the packet is forwarded or dropped.
or host sourceA source and source wildcard of source 0.0.0.0.
permit {source [source-wildcard] | host source anyA source and source wildcard of 0.0.0.0
| any} [log] | smartlog] 255.255.255.255.
To remove a named standard ACL, use the no ip access-list standard name global configuration
command.
Beginning in privileged EXEC mode, follow these steps to create an extended ACL using names:
Command Purpose
Step 2 ip access-list extended name Define an extended IPv4 access list using a name, and enter
access-list configuration mode.
The name can be a number from 100 to 199.
Step 3 {deny | permit} protocol {source In access-list configuration mode, specify the conditions allowed
[source-wildcard] | host source | any} or denied. Use the log keyword to get access list logging messages,
{destination [destination-wildcard] | host including violations.
destination | any} [precedence precedence] See the Creating a Numbered Extended ACL section on
[tos tos] [established] [log | smartlog] page 36-11 for definitions of protocols and other keywords.
[time-range time-range-name]
host sourceA source and source wildcard of source 0.0.0.0.
host destinationA destination and destination wildcard of
destination 0.0.0.0.
anyA source and source wildcard or destination and
destination wildcard of 0.0.0.0 255.255.255.255.
To remove a named extended ACL, use the no ip access-list extended name global configuration
command.

OL-21521-03 36-17
When you are creating standard extended ACLs, remember that, by default, the end of the ACL contains
an implicit deny statement for everything if it did not find a match before reaching the end. For standard
ACLs, if you omit the mask from an associated IP host address access list specification, 0.0.0.0 is
assumed to be the mask.
After you create an ACL, any additions are placed at the end of the list. You cannot selectively add ACL
entries to a specific ACL. However, you can use no permit and no deny access-list configuration mode
commands to remove entries from a named ACL. This example shows how you can delete individual
ACEs from the named access list border-list:
Switch(config)# ip access-list extended border-list
Switch(config-ext-nacl)# no permit ip host 10.1.1.3 any
Being able to selectively remove lines from a named ACL is one reason you might use named ACLs
instead of numbered ACLs.
After creating a named ACL, you can apply it to interfaces (see the Applying an IPv4 ACL to an
Interface section on page 36-21) or to VLANs (see the Configuring VLAN Maps section on
page 36-32).
Using Time Ranges with ACLs

You can selectively apply extended ACLs based on the time of day and the week by using the time-range
global configuration command. First, define a time-range name and set the times and the dates or the
days of the week in the time range. Then enter the time-range name when applying an ACL to set
restrictions to the access list. You can use the time range to define when the permit or deny statements
in the ACL are in effect, for example, during a specified time period or on specified days of the week.
The time-range keyword and argument are referenced in the named and numbered extended ACL task
tables in the previous sections, the Creating Standard and Extended IPv4 ACLs section on page 36-8,
and the Creating Named Standard and Extended ACLs section on page 36-16.
These are some benefits of using time ranges:
You have more control over permitting or denying a user access to resources, such as an application
(identified by an IP address/mask pair and a port number).
You can control logging messages. ACL entries can be set to log traffic only at certain times of the
day. Therefore, you can simply deny access without needing to analyze many logs generated during
peak hours.
Time-based access lists trigger CPU activity because the new configuration of the access list must be
merged with other features and the combined configuration loaded into the hardware memory. For this
reason, you should be careful not to have several access lists configured to take affect in close succession
(within a small number of minutes of each other.)
Note The time range relies on the switch system clock; therefore, you need a reliable clock source. We
recommend that you use Network Time Protocol (NTP) to synchronize the switch clock. For more
information, see the Managing the System Time and Date section on page 7-1.

36-18 OL-21521-03
Beginning in privileged EXEC mode, follow these steps to configure a time-range parameter for an ACL:
Command Purpose
Step 2 time-range time-range-name Assign a meaningful name (for example, workhours) to the time range to
be created, and enter time-range configuration mode. The name cannot
contain a space or quotation mark and must begin with a letter.
Step 3 absolute [start time date] Specify when the function it will be applied to is operational.
[end time date]
You can use only one absolute statement in the time range. If you
or configure more than one absolute statement, only the one configured
periodic day-of-the-week hh:mm to last is executed.
[day-of-the-week] hh:mm
You can enter multiple periodic statements. For example, you could
or configure different hours for weekdays and weekends.
periodic {weekdays | weekend | daily}
See the example configurations.
hh:mm to hh:mm
Step 5 show time-range Verify the time-range configuration.
Repeat the steps if you have multiple items that you want in effect at different times.
To remove a configured time-range limitation, use the no time-range time-range-name global
configuration command.
This example shows how to configure time ranges for workhours and to configure January 1, 2006, as a
company holiday and to verify your configuration.
Switch(config)# time-range workhours
Switch(config-time-range)# periodic weekdays 8:00 to 12:00
Switch(config-time-range)# periodic weekdays 13:00 to 17:00
Switch(config-time-range)# exit
Switch(config)# time-range new_year_day_2006
Switch(config-time-range)# absolute start 00:00 1 Jan 2006 end 23:59 1 Jan 2006
Switch(config-time-range)# end
Switch# show time-range
time-range entry: new_year_day_2003 (inactive)
absolute start 00:00 01 January 2006 end 23:59 01 January 2006
time-range entry: workhours (inactive)
periodic weekdays 8:00 to 12:00
periodic weekdays 13:00 to 17:00
To apply a time range, enter the time-range name in an extended ACL that can implement time ranges.
This example shows how to create and verify extended access list 188 that denies TCP traffic from any
source to any destination during the defined holiday times and permits all TCP traffic during work hours.
Switch(config)# access-list 188 deny tcp any any time-range new_year_day_2006
Switch(config)# access-list 188 permit tcp any any time-range workhours
Switch(config)# end
10 deny tcp any any time-range new_year_day_2006 (inactive)
20 permit tcp any any time-range workhours (inactive)

OL-21521-03 36-19
This example uses named ACLs to permit and deny the same traffic.
Switch(config)# ip access-list extended deny_access
Switch(config-ext-nacl)# deny tcp any any time-range new_year_day_2006
Switch(config-ext-nacl)# exit
Switch(config)# ip access-list extended may_access
Switch(config-ext-nacl)# permit tcp any any time-range workhours
Switch(config-ext-nacl)# end
Switch# show ip access-lists
Extended IP access list lpip_default
10 permit ip any any
Extended IP access list deny_access
10 deny tcp any any time-range new_year_day_2006 (inactive)
Extended IP access list may_access
10 permit tcp any any time-range workhours (inactive)
Including Comments in ACLs

You can use the remark keyword to include comments (remarks) about entries in any IP standard or
extended ACL. The remarks make the ACL easier for you to understand and scan. Each remark line is
limited to 100 characters.
The remark can go before or after a permit or deny statement. You should be consistent about where you
put the remark so that it is clear which remark describes which permit or deny statement. For example,
it would be confusing to have some remarks before the associated permit or deny statements and some
remarks after the associated statements.
To include a comment for IP numbered standard or extended ACLs, use the access-list access-list
number remark remark global configuration command. To remove the remark, use the no form of this
command.
In this example, the workstation that belongs to Jones is allowed access, and the workstation that belongs
to Smith is not allowed access:
Switch(config)# access-list 1 remark Permit only Jones workstation through
Switch(config)# access-list 1 permit 171.69.2.88
Switch(config)# access-list 1 remark Do not allow Smith through
Switch(config)# access-list 1 deny 171.69.3.13
For an entry in a named IP ACL, use the remark access-list configuration command. To remove the
remark, use the no form of this command.
In this example, the Jones subnet is not allowed to use outbound Telnet:
Switch(config)# ip access-list extended telnetting
Switch(config-ext-nacl)# remark Do not allow Jones subnet to telnet out
Switch(config-ext-nacl)# deny tcp host 171.69.2.88 any eq telnet
Applying an IPv4 ACL to a Terminal Line

You can use numbered ACLs to control access to one or more terminal lines. You cannot apply named
ACLs to lines. You must set identical restrictions on all the virtual terminal lines because a user can
attempt to connect to any of them.
For procedures for applying ACLs to interfaces, see the Applying an IPv4 ACL to an Interface section
on page 36-21. For applying ACLs to VLANs, see the Configuring VLAN Maps section on
page 36-32.

36-20 OL-21521-03
Beginning in privileged EXEC mode, follow these steps to restrict incoming and outgoing connections
between a virtual terminal line and the addresses in an ACL:
Command Purpose
Step 2 line [console | vty] line-number Identify a specific line to configure, and enter in-line configuration mode.
consoleSpecify the console terminal line. The console port is DCE.
vtySpecify a virtual terminal for remote console access.
The line-number is the first line number in a contiguous group that you want
to configure when the line type is specified. The range is from 0 to 16.
Step 3 access-class access-list-number Restrict incoming and outgoing connections between a particular virtual
{in | out} terminal line (into a device) and the addresses in an access list.
Step 5 show running-config Display the access list configuration.
To remove an ACL from a terminal line, use the no access-class access-list-number {in | out} line
configuration command.
Applying an IPv4 ACL to an Interface

This section describes how to apply IPv4 ACLs to network interfaces. Note these guidelines:
Apply an ACL only to inbound Layer 2 interfaces. Apply an ACL to either outbound or inbound
Layer 3 interfaces.
Note On switches running the LAN base feature set, router (Layer 3) ACLs are supported only on SVIs and
not on physical interfaces or Layer 3 EtherChannels.
When controlling access to an interface, you can use a named or numbered ACL.
If you apply an ACL to a Layer 2 interface that is a member of a VLAN, the Layer 2 (port) ACL
takes precedence over an input Layer 3 ACL applied to the VLAN interface or a VLAN map applied
to the VLAN. Incoming packets received on the Layer 2 port are always filtered by the port ACL.
If you apply an ACL to a Layer 3 interface and routing is not enabled on the switch, the ACL only
filters packets that are intended for the CPU, such as SNMP, Telnet, or web traffic. You do not have
to enable routing to apply ACLs to Layer 2 interfaces.
When private VLANs are configured, you can apply router ACLs only on the primary-VLAN SVIs.
The ACL is applied to both primary and secondary VLAN Layer 3 traffic.
When you configure an egress ACL to permit traffic with a particular DSCP value, you must use
the original DSCP value instead of a rewritten value.

OL-21521-03 36-21
Note By default, the router sends Internet Control Message Protocol (ICMP) unreachable messages when a
packet is denied by an access group. These access-group denied packets are not dropped in hardware but
are bridged to the switch CPU so that it can generate the ICMP-unreachable message. Port ACLs are an
exception. They do not generate ICMP unreachable messages.
ICMP unreachable messages can be disabled on router ACLs with the no ip unreachables interface
command.
Beginning in privileged EXEC mode, follow these steps to control access to an interface:
Command Purpose
Step 2 interface interface-id Identify a specific interface for configuration, and enter interface
configuration mode.
The interface can be a Layer 2 interface (port ACL), or a Layer 3 interface
(router ACL).
Step 3 ip access-group {access-list-number | Control access to the specified interface.
name} {in | out}
The out keyword is not supported for Layer 2 interfaces (port ACLs).
To remove the specified access group, use the no ip access-group {access-list-number | name} {in | out}
interface configuration command.
This example shows how to apply access list 2 to a port to filter packets entering the port:
Switch(config)# interface gigabitethernet1/0/1
Router(config-if)# ip access-group 2 in
Note When you apply the ip access-group interface configuration command to a Layer 3 interface (an SVI, a
Layer 3 EtherChannel, or a routed port), the interface must have been configured with an IP address.
Layer 3 access groups filter packets that are routed or are received by Layer 3 processes on the CPU.
They do not affect packets bridged within a VLAN.
For inbound ACLs, after receiving a packet, the switch checks the packet against the ACL. If the ACL
permits the packet, the switch continues to process the packet. If the ACL rejects the packet, the switch
discards the packet.
For outbound ACLs, after receiving and routing a packet to a controlled interface, the switch checks the
packet against the ACL. If the ACL permits the packet, the switch sends the packet. If the ACL rejects
the packet, the switch discards the packet.
By default, the input interface sends ICMP Unreachable messages whenever a packet is discarded,
regardless of whether the packet was discarded because of an ACL on the input interface or because of
an ACL on the output interface. ICMP Unreachables are normally limited to no more than one every
one-half second per input interface, but this can be changed by using the ip icmp rate-limit unreachable
global configuration command.

36-22 OL-21521-03
When you apply an undefined ACL to an interface, the switch acts as if the ACL has not been applied to
the interface and permits all packets. Remember this behavior if you use undefined ACLs for network
security.
Hardware and Software Treatment of IP ACLs

ACL processing is primarily accomplished in hardware, but requires forwarding of some traffic flows to
the CPU for software processing. If the hardware reaches its capacity to store ACL configurations,
packets are sent to the CPU for forwarding. The forwarding rate for software-forwarded traffic is
substantially less than for hardware-forwarded traffic.
Note If an ACL configuration cannot be implemented in hardware due to an out-of-resource condition on a

switch or stack member, then only the traffic in that VLAN arriving on that switch is affected (forwarded
in software). Software forwarding of packets might adversely impact the performance of the switch or
switch stack, depending on the number of CPU cycles that this consumes.
For router ACLs, other factors can cause packets to be sent to the CPU:
Using the log keyword
Generating ICMP unreachable messages
When traffic flows are both logged and forwarded, forwarding is done by hardware, but logging must be
done by software. Because of the difference in packet handling capacity between hardware and software,
if the sum of all flows being logged (both permitted flows and denied flows) is of great enough
bandwidth, not all of the packets that are forwarded can be logged.
If router ACL configuration cannot be applied in hardware, packets arriving in a VLAN that must be
routed are routed in software, but are bridged in hardware. If ACLs cause large numbers of packets to be
sent to the CPU, the switch performance can be negatively affected.
When you enter the show ip access-lists privileged EXEC command, the match count displayed does
not account for packets that are access controlled in hardware. Use the show access-lists hardware
counters privileged EXEC command to obtain some basic hardware ACL statistics for switched and
routed packets.
Router ACLs function as follows:
The hardware controls permit and deny actions of standard and extended ACLs (input and output)
for security access control.
If log has not been specified, the flows that match a deny statement in a security ACL are dropped
by the hardware if ip unreachables is disabled. The flows matching a permit statement are switched
in hardware.
Adding the log keyword to an ACE in a router ACL causes a copy of the packet to be sent to the
CPU for logging only. If the ACE is a permit statement, the packet is still switched and routed
in hardware.
Troubleshooting ACLs
If this ACL manager message appears and [chars] is the access-list name,
ACLMGR-2-NOVMR: Cannot generate hardware representation of access list [chars]

OL-21521-03 36-23
The switch has insufficient resources to create a hardware representation of the ACL. The resources
include hardware memory and label space but not CPU memory. A lack of available logical operation
units or specialized hardware resources causes this problem. Logical operation units are needed for a
TCP flag match or a test other than eq (ne, gt, lt, or range) on TCP, UDP, or SCTP port numbers.
Use one of these workarounds:
Modify the ACL configuration to use fewer resources.
Rename the ACL with a name or number that alphanumerically precedes the ACL names or
numbers.
To determine the specialized hardware resources, enter the show platform layer4 acl map privileged
EXEC command. If the switch does not have available resources, the output shows that index 0 to
index 15 are not available.
For more information about configuring ACLs with insufficient resources, see CSCsq63926 in the Bug
Toolkit.
For example, if you apply this ACL to an interface:
permit tcp source source-wildcard destination destination-wildcard range 5 60
permit tcp source source-wildcard destination destination-wildcard
And if this message appears:

ACLMGR-2-NOVMR: Cannot generate hardware representation of access list [chars]
The flag-related operators are not available. To avoid this issue,

Move the fourth ACE before the first ACE by using ip access-list resequence global configuration
command:
permit tcp source source-wildcard destination destination-wildcard
or
Rename the ACL with a name or number that alphanumerically precedes the other ACLs (for
example, rename ACL 79 to ACL 1).
You can now apply the first ACE in the ACL to the interface. The switch allocates the ACE to available
mapping bits in the Opselect index and then allocates flag-related operators to use the same bits in the
hardware memory.
IPv4 ACL Configuration Examples

This section provides examples of configuring and applying IPv4 ACLs. For detailed information about
compiling ACLs, see the Cisco IOS Security Configuration Guide, Release 12.4 and to the Configuring
IP Services section in the IP Addressing and Services chapter of the Cisco IOS IP Configuration
Guide, Release 12.4.
ACLs in a Small Networked Office, page 36-25
Numbered ACLs, page 36-26
Extended ACLs, page 36-26
Named ACLs, page 36-27

36-24 OL-21521-03
Time Range Applied to an IP ACL, page 36-27

Commented IP ACL Entries, page 36-28
ACL Logging, page 36-28
ACLs in a Small Networked Office

Figure 36-3 shows a small networked office environment with routed Port 2 connected to Server A,
containing benefits and other information that all employees can access, and routed Port 1 connected to
Server B, containing confidential payroll data. All users can access Server A, but Server B has restricted
access.
Use router ACLs to do this in one of two ways:
Create a standard ACL, and filter traffic coming to the server from Port 1.
Create an extended ACL, and filter traffic coming from the server into Port 1.
Figure 36-3 Using Router ACLs to Control Traffic
Server A Server B
Benefits Payroll
Port 2 Port 1
Human Resources Accounting

172.20.128.0-31 172.20.128.64-95
101354
This example uses a standard ACL to filter traffic coming into Server B from a port, permitting traffic
only from Accountings source addresses 172.20.128.64 to 172.20.128.95. The ACL is applied to traffic
coming out of routed Port 1 from the specified source address.
Switch(config)# access-list 6 permit 172.20.128.64 0.0.0.31
Switch(config)# end
Standard IP access list 6
10 permit 172.20.128.64, wildcard bits 0.0.0.31
Switch(config-if)# ip access-group 6 out

OL-21521-03 36-25
This example uses an extended ACL to filter traffic coming from Server B into a port, permitting traffic
from any source address (in this case Server B) to only the Accounting destination addresses
172.20.128.64 to 172.20.128.95. The ACL is applied to traffic going into routed Port 1, permitting it to
go only to the specified destination addresses. Note that with extended ACLs, you must enter the
protocol (IP) before the source and destination information.
Switch(config)# access-list 106 permit ip any 172.20.128.64 0.0.0.31
Switch(config)# end
10 permit ip any 172.20.128.64 0.0.0.31
Switch(config-if)# ip access-group 106 in
Numbered ACLs
In this example, network 36.0.0.0 is a Class A network whose second octet specifies a subnet; that is, its
subnet mask is 255.255.0.0. The third and fourth octets of a network 36.0.0.0 address specify a particular
host. Using access list 2, the switch accepts one address on subnet 48 and reject all others on that subnet.
The last line of the list shows that the switch accepts addresses on all other network 36.0.0.0 subnets.
The ACL is applied to packets entering a port.
Switch(config)# access-list 2 deny 36.48.0.0 0.0.255.255
Switch(config)# access-list 2 permit 36.0.0.0 0.255.255.255
Extended ACLs
In this example, the first line permits any incoming TCP connections with destination ports greater than
1023. The second line permits incoming TCP connections to the Simple Mail Transfer Protocol (SMTP)
port of host 128.88.1.2. The third line permits incoming ICMP messages for error feedback.
Switch(config)# access-list 102 permit tcp any 128.88.0.0 0.0.255.255 gt 1023
Switch(config)# access-list 102 permit tcp any host 128.88.1.2 eq 25
Switch(config)# access-list 102 permit icmp any any
In this example, suppose that you have a network connected to the Internet, and you want any host on
the network to be able to form TCP connections to any host on the Internet. However, you do not want
IP hosts to be able to form TCP connections to hosts on your network, except to the mail (SMTP) port
of a dedicated mail host.
SMTP uses TCP port 25 on one end of the connection and a random port number on the other end. The
same port numbers are used throughout the life of the connection. Mail packets coming in from the
Internet have a destination port of 25. Outbound packets have the port numbers reversed. Because the
secure system of the network always accepts mail connections on port 25, the incoming and outgoing
services are separately controlled. The ACL must be configured as an input ACL on the outbound
interface and an output ACL on the inbound interface.
Switch(config)# access-list 102 permit tcp any 128.88.0.0 0.0.255.255 eq 23
Switch(config)# access-list 102 permit tcp any 128.88.0.0 0.0.255.255 eq 25
Switch(config)# interface gigabitethernet0/1

36-26 OL-21521-03
In this example, the network is a Class B network with the address 128.88.0.0, and the mail host address
is 128.88.1.2. The established keyword is used only for the TCP to show an established connection. A
match occurs if the TCP datagram has the ACK or RST bits set, which show that the packet belongs to
an existing connection. Gigabit Ethernet interface 1 on stack member 1 is the interface that connects the
router to the Internet.
Switch(config)# access-list 102 permit tcp any 128.88.0.0 0.0.255.255 established
Switch(config)# access-list 102 permit tcp any host 128.88.1.2 eq 25
Named ACLs
This example creates a standard ACL named internet_filter and an extended ACL named
marketing_group. The internet_filter ACL allows all traffic from the source address 1.2.3.4.
Switch(config)# ip access-list standard Internet_filter
Switch(config-ext-nacl)# permit 1.2.3.4
The marketing_group ACL allows any TCP Telnet traffic to the destination address and wildcard
171.69.0.0 0.0.255.255 and denies any other TCP traffic. It permits ICMP traffic, denies UDP traffic
from any source to the destination address range 171.69.0.0 through 179.69.255.255 with a destination
port less than 1024, denies any other IP traffic, and provides a log of the result.
Switch(config)# ip access-list extended marketing_group
Switch(config-ext-nacl)# permit tcp any 171.69.0.0 0.0.255.255 eq telnet
Switch(config-ext-nacl)# deny tcp any any
Switch(config-ext-nacl)# permit icmp any any
Switch(config-ext-nacl)# deny udp any 171.69.0.0 0.0.255.255 lt 1024
Switch(config-ext-nacl)# deny ip any any log
The Internet_filter ACL is applied to outgoing traffic and the marketing_group ACL is applied to
incoming traffic on a Layer 3 port.
Switch(config-if)# no switchport
Switch(config-if)# ip address 2.0.5.1 255.255.255.0
Switch(config-if)# ip access-group Internet_filter out
Switch(config-if)# ip access-group marketing_group in
Time Range Applied to an IP ACL

This example denies HTTP traffic on IP on Monday through Friday between the hours of 8:00 a.m. and
6:00 p.m (18:00). The example allows UDP traffic only on Saturday and Sunday from noon to 8:00 p.m.
(20:00).
Switch(config)# time-range no-http
Switch(config)# periodic weekdays 8:00 to 18:00
!
Switch(config)# time-range udp-yes
Switch(config)# periodic weekend 12:00 to 20:00
!
Switch(config)# ip access-list extended strict
Switch(config-ext-nacl)# deny tcp any any eq www time-range no-http
Switch(config-ext-nacl)# permit udp any any time-range udp-yes
!

OL-21521-03 36-27
Switch(config-if)# ip access-group strict in
Commented IP ACL Entries

In this example of a numbered ACL, the workstation that belongs to Jones is allowed access, and the
workstation that belongs to Smith is not allowed access:
Switch(config)# access-list 1 remark Permit only Jones workstation through
Switch(config)# access-list 1 remark Do not allow Smith workstation through
Switch(config)# access-list 1 deny 171.69.3.13
In this example of a numbered ACL, the Winter and Smith workstations are not allowed to browse the
web:
Switch(config)# access-list 100 remark Do not allow Winter to browse the web
Switch(config)# access-list 100 deny host 171.69.3.85 any eq www
Switch(config)# access-list 100 remark Do not allow Smith to browse the web
Switch(config)# access-list 100 deny host 171.69.3.13 any eq www
In this example of a named ACL, the Jones subnet is not allowed access:
Switch(config)# ip access-list standard prevention
Switch(config-std-nacl)# remark Do not allow Jones subnet through
Switch(config-std-nacl)# deny 171.69.0.0 0.0.255.255
In this example of a named ACL, the Jones subnet is not allowed to use outbound Telnet:
Switch(config)# ip access-list extended telnetting
Switch(config-ext-nacl)# remark Do not allow Jones subnet to telnet out
Switch(config-ext-nacl)# deny tcp 171.69.0.0 0.0.255.255 any eq telnet
ACL Logging
Two variations of logging are supported on router ACLs. The log keyword sends an informational
logging message to the console about the packet that matches the entry; the log-input keyword includes
the input interface in the log entry.
In this example, standard named access list stan1 denies traffic from 10.1.1.0 0.0.0.255, allows traffic
from all other sources, and includes the log keyword.
Switch(config)# ip access-list standard stan1
Switch(config-std-nacl)# deny 10.1.1.0 0.0.0.255 log
Switch(config-std-nacl)# permit any log
Switch(config-std-nacl)# exit
Switch(config-if)# ip access-group stan1 in
Switch(config-if)# end
Switch# show logging
Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)
Console logging: level debugging, 37 messages logged
Monitor logging: level debugging, 0 messages logged
Buffer logging: level debugging, 37 messages logged
File logging: disabled
Trap logging: level debugging, 39 message lines logged
Log Buffer (4096 bytes):
00:00:48: NTP: authentication delay calculation problems

36-28 OL-21521-03
Creating Named MAC Extended ACLs
<output truncated>
00:09:34:%SEC-6-IPACCESSLOGS:list stan1 permitted 0.0.0.0 1 packet

00:09:59:%SEC-6-IPACCESSLOGS:list stan1 denied 10.1.1.15 1 packet
00:10:11:%SEC-6-IPACCESSLOGS:list stan1 permitted 0.0.0.0 1 packet
This example is a named extended access list ext1 that permits ICMP packets from any source to 10.1.1.0
0.0.0.255 and denies all UDP packets.
Switch(config)# ip access-list extended ext1
Switch(config-ext-nacl)# permit icmp any 10.1.1.0 0.0.0.255 log
Switch(config-ext-nacl)# deny udp any any log
Switch(config-std-nacl)# exit
Switch(config-if)# ip access-group ext1 in
This is a an example of a log for an extended ACL:

01:24:23:%SEC-6-IPACCESSLOGDP:list ext1 permitted icmp 10.1.1.15 -> 10.1.1.61 (0/0), 1
packet
01:25:14:%SEC-6-IPACCESSLOGDP:list ext1 permitted icmp 10.1.1.15 -> 10.1.1.61 (0/0), 7
packets
01:26:12:%SEC-6-IPACCESSLOGP:list ext1 denied udp 0.0.0.0(0) -> 255.255.255.255(0), 1
packet
01:31:33:%SEC-6-IPACCESSLOGP:list ext1 denied udp 0.0.0.0(0) -> 255.255.255.255(0), 8
packets
Note that all logging entries for IP ACLs start with %SEC-6-IPACCESSLOG with minor variations in format
depending on the kind of ACL and the access entry that has been matched.
This is an example of an output message when the log-input keyword is entered:
00:04:21:%SEC-6-IPACCESSLOGDP:list inputlog permitted icmp 10.1.1.10 (Vlan1
0001.42ef.a400) -> 10.1.1.61 (0/0), 1 packet
A log message for the same sort of packet using the log keyword does not include the input interface
information:
00:05:47:%SEC-6-IPACCESSLOGDP:list inputlog permitted icmp 10.1.1.10 -> 10.1.1.61 (0/0), 1
packet

You can filter non-IPv4 traffic on a VLAN or on a Layer 2 interface by using MAC addresses and named
MAC extended ACLs. The procedure is similar to that of configuring other extended named ACLs.
Note You cannot apply named MAC extended ACLs to Layer 3 interfaces.
For more information about the supported non-IP protocols in the mac access-list extended command,
see the command reference for this release.
Note Though visible in the command-line help strings, appletalk is not supported as a matching condition for
the deny and permit MAC access-list configuration mode commands.

OL-21521-03 36-29
Beginning in privileged EXEC mode, follow these steps to create a named MAC extended ACL:
Command Purpose
Step 2 mac access-list extended name Define an extended MAC access list using a name.
Step 3 {deny | permit} {any | host source MAC In extended MAC access-list configuration mode, specify to
address | source MAC address mask} {any | permit or deny any source MAC address, a source MAC address
host destination MAC address | destination with a mask, or a specific host source MAC address and any
MAC address mask} [type mask | lsap lsap mask destination MAC address, destination MAC address with a mask,
| aarp | amber | dec-spanning | decnet-iv | or a specific destination MAC address.
diagnostic | dsm | etype-6000 | etype-8042 | lat (Optional) You can also enter these options:
| lavc-sca | mop-console | mop-dump | msdos |
mumps | netbios | vines-echo |vines-ip | type maskAn arbitrary EtherType number of a packet with
xns-idp | 0-65535] [cos cos] Ethernet II or SNAP encapsulation in decimal, hexadecimal,
or octal with optional mask of dont care bits applied to the
EtherType before testing for a match.
lsap lsap maskAn LSAP number of a packet with
IEEE 802.2 encapsulation in decimal, hexadecimal, or octal
with optional mask of dont care bits.
aarp | amber | dec-spanning | decnet-iv | diagnostic | dsm |
etype-6000 | etype-8042 | lat | lavc-sca | mop-console |
mop-dump | msdos | mumps | netbios | vines-echo |vines-ip
| xns-idpA non-IP protocol.
cos cosAn IEEE 802.1Q cost of service number from 0 to 7
used to set priority.
Use the no mac access-list extended name global configuration command to delete the entire ACL. You
can also delete individual ACEs from named MAC extended ACLs.
This example shows how to create and display an access list named mac1, denying only EtherType
DECnet Phase IV traffic, but permitting all other types of traffic.
Switch(config)# mac access-list extended mac1
Switch(config-ext-macl)# deny any any decnet-iv
Switch(config-ext-macl)# permit any any
Switch(config-ext-macl)# end
Switch # show access-lists
Extended MAC access list mac1
10 deny any any decnet-iv
20 permit any any

36-30 OL-21521-03
Applying a MAC ACL to a Layer 2 Interface

After you create a MAC ACL, you can apply it to a Layer 2 interface to filter non-IP traffic coming in
that interface. When you apply the MAC ACL, consider these guidelines:
If you apply an ACL to a Layer 2 interface that is a member of a VLAN, the Layer 2 (port) ACL
takes precedence over an input Layer 3 ACL applied to the VLAN interface or a VLAN map applied
to the VLAN. Incoming packets received on the Layer 2 port are always filtered by the port ACL.
You can apply no more than one IP access list and one MAC access list to the same Layer 2 interface.
The IP access list filters only IP packets, and the MAC access list filters non-IP packets.
A Layer 2 interface can have only one MAC access list. If you apply a MAC access list to a Layer 2
interface that has a MAC ACL configured, the new ACL replaces the previously configured one.
Beginning in privileged EXEC mode, follow these steps to apply a MAC access list to control access to
a Layer 2 interface:
Command Purpose
Step 2 interface interface-id Identify a specific interface, and enter interface configuration
mode. The interface must be a physical Layer 2 interface (port
ACL).
Step 3 mac access-group {name} {in} Control access to the specified interface by using the MAC access
list.
Port ACLs are supported only in the inbound direction.
Step 5 show mac access-group [interface interface-id] Display the MAC access list applied to the interface or all Layer 2
interfaces.
To remove the specified access group, use the no mac access-group {name} interface configuration
command.
This example shows how to apply MAC access list mac1 to a port to filter packets entering the port:
Router(config-if)# mac access-group mac1 in
Note The mac access-group interface configuration command is only valid when applied to a physical
Layer 2 interface.You cannot use the command on EtherChannel port channels.
After receiving a packet, the switch checks it against the inbound ACL. If the ACL permits it, the switch
continues to process the packet. If the ACL rejects the packet, the switch discards it. When you apply an
undefined ACL to an interface, the switch acts as if the ACL has not been applied and permits all packets.
Remember this behavior if you use undefined ACLs for network security.

OL-21521-03 36-31
Configuring VLAN Maps

Note VLAN maps are not supported on switches running the LAN base feature set.
This section describes how to configure VLAN maps, which is the only way to control filtering within
a VLAN. VLAN maps have no direction. To filter traffic in a specific direction by using a VLAN map,
you need to include an ACL with specific source or destination addresses. If there is a match clause for
that type of packet (IP or MAC) in the VLAN map, the default action is to drop the packet if the packet
does not match any of the entries within the map. If there is no match clause for that type of packet, the
default is to forward the packet.
For complete syntax and usage information for the commands used in this section, see the command
reference for this release.
To create a VLAN map and apply it to one or more VLANs, perform these steps:
Step 1 Create the standard or extended IPv4 ACLs or named MAC extended ACLs that you want to apply to the
VLAN. See the Creating Standard and Extended IPv4 ACLs section on page 36-8 and the Creating a
VLAN Map section on page 36-34.
Step 2 Enter the vlan access-map global configuration command to create a VLAN ACL map entry.
Step 3 In access-map configuration mode, optionally enter an actionforward (the default) or dropand
enter the match command to specify an IP packet or a non-IP packet (with only a known MAC address)
and to match the packet against one or more ACLs (standard or extended).
Note If the VLAN map is configured with a match clause for a type of packet (IP or MAC) and the map action
is drop, all packets that match the type are dropped. If the VLAN map has no match clause, and the
configured action is drop, all IP and Layer 2 packets are dropped.
Step 4 Use the vlan filter global configuration command to apply a VLAN map to one or more VLANs.
These sections contain this configuration information:

VLAN Map Configuration Guidelines, page 36-33
Creating a VLAN Map, page 36-34
Applying a VLAN Map to a VLAN, page 36-36
Using VLAN Maps in Your Network, page 36-36
Configuring VACL Logging, page 36-39

36-32 OL-21521-03
VLAN Map Configuration Guidelines

If there is no ACL configured to deny traffic on an interface and no VLAN map is configured, all
traffic is permitted.
Each VLAN map consists of a series of entries. The order of entries in an VLAN map is important.
A packet that comes into the switch is tested against the first entry in the VLAN map. If it matches,
the action specified for that part of the VLAN map is taken. If there is no match, the packet is tested
against the next entry in the map.
If the VLAN map has at least one match clause for the type of packet (IP or MAC) and the packet
does not match any of these match clauses, the default is to drop the packet. If there is no match
clause for that type of packet in the VLAN map, the default is to forward the packet.
The system might take longer to boot up if you have configured a very large number of ACLs.
Logging is not supported for VLAN maps.
When a switch has an IP access list or MAC access list applied to a Layer 2 interface, and you apply
a VLAN map to a VLAN that the port belongs to, the port ACL takes precedence over the VLAN
map.
If VLAN map configuration cannot be applied in hardware, all packets in that VLAN must be
bridged and routed by software.
You can configure VLAN maps on primary and secondary VLANs. However, we recommend that
you configure the same VLAN maps on private-VLAN primary and secondary VLANs.
When a frame is Layer-2 forwarded within a private VLAN, the same VLAN map is applied at the
ingress side and at the egress side. When a frame is routed from inside a private VLAN to an external
port, the private-VLAN map is applied at the ingress side.
For frames going upstream from a host port to a promiscuous port, the VLAN map configured
on the secondary VLAN is applied.
For frames going downstream from a promiscuous port to a host port, the VLAN map
configured on the primary VLAN is applied.
To filter out specific IP traffic for a private VLAN, you should apply the VLAN map to both the
primary and secondary VLANs. For more information about private VLANs, see Chapter 17,
Configuring Private VLANs.
For configuration examples, see the Using VLAN Maps in Your Network section on page 36-36.
For information about using both router ACLs and VLAN maps, see the VLAN Maps and Router ACL
Configuration Guidelines section on page 36-40.

OL-21521-03 36-33
Creating a VLAN Map

Each VLAN map consists of an ordered series of entries. Beginning in privileged EXEC mode, follow
these steps to create, add to, or delete a VLAN map entry:
Command Purpose
Step 2 vlan access-map name [number] Create a VLAN map, and give it a name and (optionally) a number. The
number is the sequence number of the entry within the map.
When you create VLAN maps with the same name, numbers are assigned
sequentially in increments of 10. When modifying or deleting maps, you
can enter the number of the map entry that you want to modify or delete.
Entering this command changes to access-map configuration mode.
Step 3 action {drop | forward} (Optional) Set the action for the map entry. The default is to forward.
Step 4 match {ip | mac} address {name | Match the packet (using either the IP or MAC address) against one or more
number} [name | number] standard or extended access lists. Note that packets are only matched
against access lists of the correct protocol type. IP packets are matched
against standard or extended IP access lists. Non-IP packets are only
matched against named MAC extended access lists.
Step 5 end Return to global configuration mode.
Use the no vlan access-map name global configuration command to delete a map. Use the no vlan
access-map name number global configuration command to delete a single sequence entry from within
the map.
Use the no action access-map configuration command to enforce the default action, which is to forward.
VLAN maps do not use the specific permit or deny keywords. To deny a packet by using VLAN maps,
create an ACL that would match the packet, and set the action to drop. A permit in the ACL counts as a
match. A deny in the ACL means no match.
Examples of ACLs and VLAN Maps

These examples show how to create ACLs and VLAN maps that for specific purposes.
Example 1
This example shows how to create an ACL and a VLAN map to deny a packet. In the first map, any
packets that match the ip1 ACL (TCP packets) would be dropped. You first create the ip1ACL to permit
any TCP packet and no other packets. Because there is a match clause for IP packets in the VLAN map,
the default action is to drop any IP packet that does not match any of the match clauses.
Switch(config)# ip access-list extended ip1
Switch(config-ext-nacl)# permit tcp any any
Switch(config)# vlan access-map map_1 10
Switch(config-access-map)# match ip address ip1
Switch(config-access-map)# action drop

36-34 OL-21521-03
This example shows how to create a VLAN map to permit a packet. ACL ip2 permits UDP packets and
any packets that match the ip2 ACL are forwarded. In this map, any IP packets that did not match any of
the previous ACLs (that is, packets that are not TCP packets or UDP packets) would get dropped.
Switch(config)# ip access-list extended ip2
Switch(config-ext-nacl)# permit udp any any
Switch(config)# vlan access-map map_1 20
Switch(config-access-map)# match ip address ip2
Switch(config-access-map)# action forward
Example 2
In this example, the VLAN map has a default action of drop for IP packets and a default action of forward
for MAC packets. Used with standard ACL 101 and extended named access lists igmp-match and
tcp-match, the map will have the following results:
Forward all UDP packets
Drop all IGMP packets
Forward all TCP packets
Drop all other IP packets
Forward all non-IP packets
Switch(config)# access-list 101 permit udp any any
Switch(config)# ip access-list extended igmp-match
Switch(config-ext-nacl)# permit igmp any any
Switch(config)# ip access-list extended tcp-match
Switch(config-ext-nacl)# permit tcp any any
Switch(config)# vlan access-map drop-ip-default 10
Switch(config-access-map)# match ip address 101
Switch(config-access-map)# exit
Switch(config-access-map)# match ip address igmp-match
Switch(config-access-map)# match ip address tcp-match
Example 3
In this example, the VLAN map has a default action of drop for MAC packets and a default action of
forward for IP packets. Used with MAC extended access lists good-hosts and good-protocols, the map
will have the following results:
Forward MAC packets from hosts 0000.0c00.0111 and 0000.0c00.0211
Forward MAC packets with decnet-iv or vines-ip protocols
Drop all other non-IP packets
Forward all IP packets
Switch(config)# mac access-list extended good-hosts
Switch(config-ext-macl)# permit host 000.0c00.0111 any
Switch(config-ext-macl)# permit host 000.0c00.0211 any
Switch(config)# mac access-list extended good-protocols
Switch(config-ext-macl)# permit any any decnet-ip

OL-21521-03 36-35
Switch(config-ext-macl)# permit any any vines-ip

Switch(config)# vlan access-map drop-mac-default 10
Switch(config-access-map)# match mac address good-hosts
Switch(config)# vlan access-map drop-mac-default 20
Switch(config-access-map)# match mac address good-protocols
Example 4
In this example, the VLAN map has a default action of drop for all packets (IP and non-IP). Used with
access lists tcp-match and good-hosts from Examples 2 and 3, the map will have the following results:
Forward all TCP packets
Forward MAC packets from hosts 0000.0c00.0111 and 0000.0c00.0211
Drop all other IP packets
Drop all other MAC packets
Switch(config)# vlan access-map drop-all-default 10
Switch(config-access-map)# match ip address tcp-match
Switch(config)# vlan access-map drop-all-default 20
Switch(config-access-map)# match mac address good-hosts
Applying a VLAN Map to a VLAN

Beginning in privileged EXEC mode, follow these steps to apply a VLAN map to one or more VLANs:
Command Purpose
Step 2 vlan filter mapname vlan-list list Apply the VLAN map to one or more VLAN IDs.
The list can be a single VLAN ID (22), a consecutive list (10-22), or a string
of VLAN IDs (12, 22, 30). Spaces around the comma and hyphen are
optional.
To remove the VLAN map, use the no vlan filter mapname vlan-list list global configuration command.
This example shows how to apply VLAN map 1 to VLANs 20 through 22:
Switch(config)# vlan filter map 1 vlan-list 20-22
Using VLAN Maps in Your Network

Wiring Closet Configuration, page 36-37
Denying Access to a Server on Another a VLAN, page 36-38

36-36 OL-21521-03
Wiring Closet Configuration

In a wiring closet configuration, routing might not be enabled on the switch. In this configuration, the
switch can still support a VLAN map and a QoS classification ACL. In Figure 36-4, assume that Host X
and Host Y are in different VLANs and are connected to wiring closet switches A and C. Traffic from
Host X to Host Y is eventually being routed by Switch B, a Layer 3 switch with routing enabled. Traffic
from Host X to Host Y can be access-controlled at the traffic entry point, Switch A.
Figure 36-4 Wiring Closet Configuration
Switch B
Switch A Switch C
VLAN map: Deny HTTP

from X to Y.
HTTP is dropped
at entry point.
Host X Host Y
10.1.1.32 10.1.1.34
VLAN 1
101355
VLAN 2
Packet
If you do not want HTTP traffic switched from Host X to Host Y, you can configure a VLAN map on
Switch A to drop all HTTP traffic from Host X (IP address 10.1.1.32) to Host Y (IP address 10.1.1.34)
at Switch A and not bridge it to Switch B.
First, define the IP access list http that permits (matches) any TCP traffic on the HTTP port.
Switch(config)# ip access-list extended http
Switch(config-ext-nacl)# permit tcp host 10.1.1.32 host 10.1.1.34 eq www
Next, create VLAN access map map2 so that traffic that matches the http access list is dropped and all
other IP traffic is forwarded.
Switch(config)# vlan access-map map2 10
Switch(config-access-map)# match ip address http
Switch(config)# ip access-list extended match_all
Switch(config-ext-nacl)# permit ip any any
Switch(config)# vlan access-map map2 20
Switch(config-access-map)# match ip address match_all
Then, apply VLAN access map map2 to VLAN 1.

Switch(config)# vlan filter map2 vlan 1

OL-21521-03 36-37
Denying Access to a Server on Another a VLAN

You can restrict access to a server on another VLAN. For example, server 10.1.1.100 in VLAN 10 needs
to have access denied to these hosts (see Figure 36-5):
Hosts in subnet 10.1.2.0/8 in VLAN 20 should not have access.
Hosts 10.1.1.4 and 10.1.1.8 in VLAN 10 should not have access.
Figure 36-5 Deny Access to a Server on Another VLAN
VLAN map
10.1.1.100
Subnet
Server (VLAN 10) 10.1.2.0/8
10.1.1.4
Host (VLAN 20)
Host (VLAN 10) Layer 3 switch
10.1.1.8
101356
Host (VLAN 10) Packet
This example shows how to deny access to a server on another VLAN by creating the VLAN map
SERVER 1 that denies access to hosts in subnet 10.1.2.0.8, host 10.1.1.4, and host 10.1.1.8 and permits
other IP traffic. The final step is to apply the map SERVER1 to VLAN 10.
Step 1 Define the IP ACL that will match the correct packets.
Switch(config)# ip access-list extended SERVER1_ACL
Switch(config-ext-nacl))# permit ip 10.1.2.0 0.0.0.255 host 10.1.1.100
Switch(config-ext-nacl))# permit ip host 10.1.1.4 host 10.1.1.100
Switch(config-ext-nacl))# permit ip host 10.1.1.8 host 10.1.1.100
Switch(config-ext-nacl))# exit
Step 2 Define a VLAN map using this ACL that will drop IP packets that match SERVER1_ACL and forward
IP packets that do not match the ACL.
Switch(config)# vlan access-map SERVER1_MAP
Switch(config-access-map)# match ip address SERVER1_ACL
Switch(config)# vlan access-map SERVER1_MAP 20
Step 3 Apply the VLAN map to VLAN 10.

Switch(config)# vlan filter SERVER1_MAP vlan-list 10.

36-38 OL-21521-03
Configuring VACL Logging

When you configure VACL logging, syslog messages are generated for denied IP packets under these
circumstances:
When the first matching packet is received.
For any matching packets received within the last 5 minutes.
If the threshold is reached before the 5-minute interval.
Log messages are generated on a per-flow basis. A flow is defined as packets with the same IP addresses and
Layer 4 (UDP or TCP) port numbers. If a flow does not receive any packets in the 5-minute interval, that
flow is removed from the cache. When a syslog message is generated, the timer and packet counter are
reset.
VACL logging restrictions:
Only denied IP packets are logged.
Packets that require logging on the outbound port ACLs are not logged if they are denied by a VACL.
Beginning in privileged EXEC mode:
Command Purpose
Step 1 configure terminal Enter the global configuration mode.
Step 2 vlan access-map name [number] Create a VLAN map. Give it a name and optionally a number. The number
is the sequence number of the entry within the map.
The sequence number range is from 0 to 65535.
When you create VLAN maps with the same name, numbers are assigned
sequentially in increments of 10. When modifying or deleting maps, you can
enter the number of the map entry that you want to modify or delete.
Specifying the map name and optionally a number enters the access-map
configuration mode.
Step 3 action drop log Set the VLAN access map to drop and log IP packets.
Step 4 exit Exit the VLAN access map configuration mode and return to the global
configuration mode.
Step 5 vlan access-log {maxflow Configure the VACL logging parameters.
max_number | threshold pkt_count}
maxflow max_numberSet the log table size. The content of the log
table can be deleted by setting the maxflow to 0. When the log table is
full, the sofware drops logged packets from new flows.
The range is from 0 to 2048. The default is 500.
threshold pkt_countSet the logging threshold. A logging message is
generated if the threshold for a flow is reached before the 5-minute interval.
The threshold range is from 0 to 2147483647. The default threshold is
0, which means that a syslog message is generated every 5 minutes.
Step 6 exit Return to privileged EXEC mode.
Step 7 show vlan access-map Verify your entries.

OL-21521-03 36-39
Using VLAN Maps with Router ACLs
Use the no vlan access-map command with a sequence number to delete a map sequence. Use the no
version of the command without a sequence number to delete the map.
This example shows how to configure a VLAN access map to drop and log IP packets. Here IP traffic
matching the permit entries in net_10 is dropped and logged.
DomainMember(config)# vlan access-map ganymede 10
DomainMember(config-access-map)# match ip address net_10
DomainMember(config-access-map)# action drop log
DomainMember(config-access-map)# exit
This example shows how to configure global VACL logging parameters:

DomainMember(config)# vlan access-log maxflow 800
DomainMember(config)# vlan access-log threshold 4000
Note For complete syntax and usage information of the commands used in this section, see the Cisco IOS LAN
Switching Command Reference:
http://www.cisco.com/en/US/docs/ios/lanswitch/command/reference/lsw_book.html

Note Router ACLs and VLAN maps are not supported on switches running the LAN base feature set.
To access control both bridged and routed traffic, you can use VLAN maps only or a combination of
router ACLs and VLAN maps. You can define router ACLs on both input and output routed VLAN
interfaces, and you can define a VLAN map to access control the bridged traffic.
If a packet flow matches a VLAN-map deny clause in the ACL, regardless of the router ACL
configuration, the packet flow is denied.
Note When you use router ACLs with VLAN maps, packets that require logging on the router ACLs are not
logged if they are denied by a VLAN map.
If the VLAN map has a match clause for the type of packet (IP or MAC) and the packet does not match
the type, the default is to drop the packet. If there is no match clause in the VLAN map, and no action
specified, the packet is forwarded if it does not match any VLAN map entry.
VLAN Maps and Router ACL Configuration Guidelines, page 36-40
Examples of Router ACLs and VLAN Maps Applied to VLANs, page 36-41
VLAN Maps and Router ACL Configuration Guidelines

These guidelines are for configurations where you need to have an router ACL and a VLAN map on the
same VLAN. These guidelines do not apply to configurations where you are mapping router ACLs and
VLAN maps on different VLANs.
The switch hardware provides one lookup for security ACLs for each direction (input and output);
therefore, you must merge a router ACL and a VLAN map when they are configured on the same VLAN.
Merging the router ACL with the VLAN map might significantly increase the number of ACEs.

36-40 OL-21521-03
If you must configure a router ACL and a VLAN map on the same VLAN, use these guidelines for both
router ACL and VLAN map configuration:
You can configure only one VLAN map and one router ACL in each direction (input/output) on a
VLAN interface.
Whenever possible, try to write the ACL with all entries having a single action except for the final,
default action of the other type. That is, write the ACL using one of these two forms:
permit...
permit...
permit...
deny ip any any
or
deny...
deny...
deny...
permit ip any any
To define multiple actions in an ACL (permit, deny), group each action type together to reduce the
number of entries.
Avoid including Layer 4 information in an ACL; adding this information complicates the merging
process. The best merge results are obtained if the ACLs are filtered based on IP addresses (source
and destination) and not on the full flow (source IP address, destination IP address, protocol, and
protocol ports). It is also helpful to use dont care bits in the IP address, whenever possible.
If you need to specify the full-flow mode and the ACL contains both IP ACEs and TCP/UDP/ICMP
ACEs with Layer 4 information, put the Layer 4 ACEs at the end of the list. This gives priority to
the filtering of traffic based on IP addresses.
Examples of Router ACLs and VLAN Maps Applied to VLANs

This section gives examples of applying router ACLs and VLAN maps to a VLAN for switched, bridged,
routed, and multicast packets. Although the following illustrations show packets being forwarded to their
destination, each time the packets path crosses a line indicating a VLAN map or an ACL, it is also
possible that the packet might be dropped, rather than forwarded.
ACLs and Switched Packets, page 36-41
ACLs and Bridged Packets, page 36-42
ACLs and Routed Packets, page 36-43
ACLs and Multicast Packets, page 36-43
ACLs and Switched Packets

Figure 36-6 shows how an ACL is applied on packets that are switched within a VLAN. Packets switched
within the VLAN without being routed or forwarded by fallback bridging are only subject to the VLAN
map of the input VLAN.

OL-21521-03 36-41
Figure 36-6 Applying ACLs on Switched Packets
Input Output
VLAN 10 router router VLAN 20
map ACL ACL map
Frame
Host A
(VLAN 10)
Routing function or
fallback bridge
Host C
(VLAN 10)
101357
VLAN 10 Packet VLAN 20
ACLs and Bridged Packets

Figure 36-7 shows how an ACL is applied on fallback-bridged packets. For bridged packets, only
Layer 2 ACLs are applied to the input VLAN. Only non-IP, non-ARP packets can be fallback-bridged.
Figure 36-7 Applying ACLs on Bridged Packets
VLAN 10 VLAN 20
map map
Frame
Host A Host B
(VLAN 10) (VLAN 20)
Fallback bridge
101358

36-42 OL-21521-03
ACLs and Routed Packets

Figure 36-8 shows how ACLs are applied on routed packets. The ACLs are applied in this order:
1. VLAN map for input VLAN
2. Input router ACL
3. Output router ACL
4. VLAN map for output VLAN
Figure 36-8 Applying ACLs on Routed Packets
Input Output
map ACL ACL map
Frame
Host A Host B
(VLAN 10) (VLAN 20)
Routing function
101359
ACLs and Multicast Packets

Figure 36-9 shows how ACLs are applied on packets that are replicated for IP multicasting. A multicast
packet being routed has two different kinds of filters applied: one for destinations that are other ports in
the input VLAN and another for each of the destinations that are in other VLANs to which the packet
has been routed. The packet might be routed to more than one output VLAN, in which case a different
router output ACL and VLAN map would apply for each destination VLAN.
The final result is that the packet might be permitted in some of the output VLANs and not in others. A
copy of the packet is forwarded to those destinations where it is permitted. However, if the input VLAN
map (VLAN 10 map in Figure 36-9) drops the packet, no destination receives a copy of the packet.

OL-21521-03 36-43
Displaying IPv4 ACL Configuration
Figure 36-9 Applying ACLs on Multicast Packets
Input Output
map ACL ACL map
Frame
Host A Host B
(VLAN 10) (VLAN 20)
Routing function
Host C
(VLAN 10)
101360

You can display the ACLs that are configured on the switch, and you can display the ACLs that have
been applied to interfaces and VLANs.
When you use the ip access-group interface configuration command to apply ACLs to a Layer 2 or 3
interface, you can display the access groups on the interface. You can also display the MAC ACLs
applied to a Layer 2 interface. You can use the privileged EXEC commands as described in Table 36-2
to display this information.
Table 36-2 Commands for Displaying Access Lists and Access Groups
Command Purpose
show access-lists [number | name] Display the contents of one or all current IP and MAC address access lists
or a specific access list (numbered or named).
show ip access-lists [number | name] Display the contents of all current IP access lists or a specific IP access list
(numbered or named).
show ip interface interface-id Display detailed configuration and status of an interface. If IP is enabled
on the interface and ACLs have been applied by using the ip access-group
interface configuration command, the access groups are included in the
display.
show running-config [interface interface-id] Displays the contents of the configuration file for the switch or the
specified interface, including all configured MAC and IP access lists and
which access groups are applied to an interface.
show mac access-group [interface interface-id] Displays MAC access lists applied to all Layer 2 interfaces or the specified
Layer 2 interface.

36-44 OL-21521-03
You can also display information about VLAN access maps or VLAN filters. Use the privileged EXEC
commands in Table 36-3 to display VLAN map information.
Table 36-3 Commands for Displaying VLAN Map Information
Command Purpose
show vlan access-map [mapname] Show information about all VLAN access maps or the
specified access map.
show vlan filter [access-map name | vlan vlan-id] Show information about all VLAN filters or about a specified
VLAN or VLAN access map.

OL-21521-03 36-45

36-46 OL-21521-03

Swacl

Uploaded by

Copyright:

Available Formats

Swacl

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Swacl

Uploaded by

Copyright:

Available Formats

CH A P T E R 36

Configuring Network Security with ACLs

This chapter consists of these sections:

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Using VLAN Maps with Router ACLs, page 36-40

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Figure 36-1 Using ACLs to Control Traffic to a Network

Human Research &

= ACL denying traffic from Host B

and permitting traffic from Host A

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Figure 36-2 Using VLAN Maps to Control Traffic

= VLAN map denying specific type

Handling Fragmented and Unfragmented Traffic

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

ACLs and Switch Stacks

Configuring IPv4 ACLs

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Inbound and outbound rate limiting (except with QoS ACLs)

These sections contain this configuration information:

Creating Standard and Extended IPv4 ACLs

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Access List Numbers

Table 36-1 Access List Numbers

Access List Number Type Supported

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Creating a Numbered Standard ACL

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Creating a Numbered Extended ACL

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Resequencing ACEs in an ACL

Creating Named Standard and Extended ACLs

Consider these guidelines and limitations before configuring named ACLs:

Note The ACL must be an extended named ACL.

match input-interface interface-id-list

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Using Time Ranges with ACLs

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Including Comments in ACLs

Applying an IPv4 ACL to a Terminal Line

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Applying an IPv4 ACL to an Interface

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

Hardware and Software Treatment of IP ACLs

Note If an ACL configuration cannot be implemented in hardware due to an out-of-resource condition on a

Catalyst 3750-X and 3560-X Switch Software Configuration Guide

And if this message appears:

The flag-related operators are not available. To avoid this issue,

IPv4 ACL Configuration Examples