CI/SfB

(47) Nh2

January 2012

purlins, rails
& eaves beams
> design guide

ms eaves beams
syste r ails floor cee
l in n g s
pur sheeti
d
ze & cee
d
ze
purlins, rails & eaves beams

Index

About Steadmans ............................................ 03 Zed and Cee Sheeting Rails . . . . . . . . . . . . . 19

Introduction ..................................................... 03 Sleeved system................................................. 19
Specification .................................................... 03 Butted system .................................................. 19
Requirements................................................... 03 Double span system (brick restraint)................. 19
Overview.......................................................... 04 Sleeved rail system ........................................... 20
Butted & double span rail system..................... 21
Zed and Cee section range . . . . . . . . . . . . . 06
Typical brick restraint details............................. 21
Zed Purlin Systems . . . . . . . . . . . . . . . . . . . . 07
Sheeting rail sag-system requirements 22
Sleeved single span system .............................. 07
Sheeting rail sag system................................... 23
Sleeved double span system............................. 07
Horizontal wall cladding requirements ............. 24
Heavy end-bay single span system ................... 07
Fire Rated Boundary Walls................................ 25
Heavy end-bay double span system.................. 07
Additional Details . . . . . . . . . . . . . . . . . . . . 26
Sleeved purlin system....................................... 08
Typical Zed section details (Cee sections similar) . 26
Butted single span system................................ 08
Parapet framing ............................................... 27
Butted purlin system ........................................ 08
Valley beam details .......................................... 28
Roof sag-system requirements ......................... 09
Door & window framing .................................. 29
Roof sag bar system......................................... 10
Suspended services & point loads .................... 30
Roof angle brace system .................................. 10
Suspended ceilings........................................... 31
Mono pitch roofs ............................................. 11
Steep pitch roofs.............................................. 12 Detailing Information . . . . . . . . . . . . . . . . . 32
Shallow pitch roofs .......................................... 12 Zed purlin and rail hole punching details ......... 32
Long roof slopes .............................................. 13 Cee rail hole punching details .......................... 33
Curved roofs .................................................... 13 Fire wall rail hole punching details ................... 34
Tiled roofs........................................................ 14 Standard cleats for purlins & rails ..................... 35
Cantilever purlins ............................................. 15 Anti-sag system components ........................... 36
Cleats .............................................................. 37
Eaves Beams . . . . . . . . . . . . . . . . . . . . . . . . . 16
Miscellaneous components .............................. 38
Sections ........................................................... 16
Custom sections .............................................. 39
Typical eaves beam details................................ 17
Typical connections to column heads ............... 17 Technical support . . . . . . . . . . . . . . . . . . . . . 40
Connections between eaves beams References ....................................................... 41
and rail struts................................................... 18

purlins, rails & eaves beams

02
About Steadmans specification
A Steadman & Son Limited (usually known as Steadmans) NBS Plus is a library of technical product information
are one of the UK's leading manufacturers of roofing and written in NBS format, linked to NBS
cladding, supplying high quality cladding materials from clauses and clause guidance.
our sites in England, Scotland and Northern Ireland. With NBS Plus, specifiers can select
We offer total roofing and cladding solutions which we products quickly and accurately then drop
deliver with our dedicated haulage fleet. the product information directly into a specification.
Our continuous investment programme and on-going NBS clauses for Zed, Cee and Eaves Beam sections and
product development ensures we can provide high quality other Steadmans products are now available for NBS
products promptly and at competitive prices. subscribers.

introduction
Requirements
This brochure contains details of our increased range of
Zed, Cee and Eaves Beam sections and accessories.
Zed, Cee and Eaves Beam sections are manufactured in a
Section profiles and dimensions are included along with process certified to ISO 9001:2008.
structural properties, detailing information and typical
construction details. Installation warranty
The new section range offers complete compatibility Steadmans offer an independent audit-based warranty for
between Zed and Cee sections sizes. Zed, Cee and Eaves Beam sections.

The products are formed from hot dipped galvanised steel The QA+ warranty, from Auditing Workmanship &
coil to BS EN 10346:2009 Fe E390G -Z275. Materials Ltd, provides pre-site and on-site quality
inspections and audits to ensure the high standards of
The sections are designed to BS EN 1993-1-3:2006 using a construction and finishing which will maximise service life
combination of rational analysis and component testing. and reduce maintenance costs.
A separate brochure containing load tables for the The QA+ warranty can be extended to a ten year insurance
Purlins, Rails & Eaves Beams is also available from backed warranty covering defects arising from poor
Steadmans upon request or as a download from our workmanship, defective materials and damage resulting
website. from design defects. Contact Steadmans for more
Steadmans realise that our standard range will not meet all information about the warranties.
requirements and therefore customer designed Zed, Cee
and Eaves Beam sections can be manufactured along with
individual designs for special applications.

Our extensive stock of full width coils in various gauges

and our capability to cut, fold and punch these materials
allow us to offer solutions to almost all situations.

Please consult Steadmans Sales Department for further

details.

purlins, rails & eaves beams

03
purlins, rails & eaves beams
overview

Sleeve
Eaves beam

Roof cladding

Wall cladding

Brickwork

Cee-section
door framing

purlins, rails & eaves beams

04
 Gable cleader angle

Purlin

Zed-section rail

Push-fit
sag bar

Eaves
brace

Cee-section rail

Diagonal tie

Rail strut

Brickwork

purlins, rails & eaves beams

05
purlins, rails & eaves beams
zed and cee section range

A E
Y Y
Table 01: Zed & Cee profile dimensions
C F
Section Zeds Cees
Depth A B C D E F
Depth

Depth
x x 140,170 60 54 16 20 62 13 x x
200 70 64 16 20 70 15
Yna 240 75 67 18 22 74 17
300 95 87 21 25 95 19
D F
Xna B Dimensions in mm
Xna
Y
Y
Table 02: Standard Zeds - 390N/mm2 steel grade
Section Wt Area Zxx Zyy Ixx lyy Rx Ry Po Qs xna yna Mc
(kg/m) (cm2) (cm3) (cm3) (cm4) (cm4) (mm) (mm) (N/mm2) (mm) (mm) (kNm)
14014 3.06 3.81 13.97 4.37 116.8 29.3 55.3 27.7 350.7 0.641 22.4 0.1 70.7 5.45
14015 3.26 4.08 15.49 4.79 124.7 31.2 55.3 27.6 356.8 0.667 22.4 0.0 70.7 6.04
14016 3.48 4.35 17.00 5.22 132.7 33.1 55.2 27.6 362.2 0.693 22.3 0.0 70.7 6.63
14018 3.90 4.89 19.87 6.04 148.4 36.8 55.1 27.4 371.1 0.731 22.2 -0.1 70.7 7.75
14020 4.32 5.43 22.44 6.83 164.0 40.4 55.0 27.3 378.2 0.762 22.2 -0.2 70.7 8.75
17014 3.38 4.22 17.44 4.18 184.0 29.4 66.0 26.4 331.4 0.582 17.3 0.0 85.8 6.80
17015 3.62 4.52 19.37 4.60 196.5 31.3 65.9 26.3 338.9 0.605 17.3 -0.1 85.8 7.55
17016 3.86 4.82 21.28 5.02 209.2 33.2 65.9 26.2 345.4 0.627 17.3 -0.1 85.8 8.30
17018 4.33 5.42 24.85 5.83 234.2 36.9 65.7 26.1 356.2 0.662 17.2 -0.2 85.8 9.69
17020 4.79 6.02 28.21 6.61 259.0 40.5 65.6 26.0 364.8 0.689 17.1 -0.3 85.8 11.00
17025 5.94 7.48 36.24 8.42 318.8 49.1 65.3 25.6 380.3 0.750 17.0 -0.6 85.8 14.14
20014 3.92 4.90 21.56 4.97 296.8 44.8 77.8 30.2 312.1 0.511 16.8 -0.1 100.7 8.41
20015 4.20 5.25 24.18 5.53 317.3 47.8 77.7 30.2 320.9 0.538 16.8 -0.1 100.7 9.43
20016 4.48 5.60 26.84 6.08 337.9 50.7 77.7 30.1 328.6 0.563 16.7 -0.2 100.7 10.47
20018 5.03 6.30 32.10 7.18 378.6 56.5 77.5 30.0 341.3 0.608 16.7 -0.3 100.7 12.52
20020 5.58 7.00 37.25 8.25 419.2 62.2 77.4 29.8 351.5 0.641 16.6 -0.4 100.7 14.53
20025 6.92 8.71 48.63 10.72 517.3 75.7 77.1 29.5 369.6 0.700 16.5 -0.6 100.7 18.97
24015 4.81 6.01 30.11 5.90 510.4 58.6 92.1 31.2 296.9 0.485 14.3 0.3 121.3 11.74
24016 5.13 6.41 33.61 6.54 543.7 62.3 92.1 31.2 306.2 0.509 14.3 0.2 121.3 13.11
24018 5.77 7.22 40.62 7.80 609.9 69.5 91.9 31.0 321.4 0.550 14.2 0.1 121.3 15.84
24020 6.39 8.02 47.36 9.04 675.8 76.5 91.8 30.9 333.6 0.583 14.2 0.0 121.3 18.47
24025 7.94 9.99 62.69 11.94 835.7 93.3 91.5 30.6 355.4 0.639 14.1 -0.2 121.3 24.45
24030 9.47 11.94 77.42 14.62 990.7 109.1 91.1 30.2 369.8 0.685 14.0 -0.5 121.3 30.19
30020 8.02 10.09 66.20 12.92 1344.7 157.4 115.4 39.5 306.8 0.503 14.5 0.0 151.3 25.82
30025 10.02 12.60 93.55 17.86 1668.1 193.1 115.1 39.2 334.1 0.581 14.4 -0.2 151.3 36.49
30030 11.97 15.08 118.11 22.48 1983.6 227.1 114.7 38.8 352.1 0.630 14.3 -0.5 151.3 46.06

Table 03: Standard Cees - 390N/mm2 steel grade

Section Wt Area Zxx Zyy Ixx lyy Rx Ry Po Qs xna yna Mc
(kg/m) (cm2) (cm3) (cm3) (cm4) (cm4) (mm) (mm) (N/mm2) (mm) (mm) (kNm)
14014 3.06 3.81 13.90 3.91 119.3 19.2 55.9 22.4 350.7 0.665 18.9 70.0 5.42
14015 3.26 4.08 15.44 4.26 127.4 20.4 55.8 22.4 356.8 0.699 18.9 70.0 6.02
14016 3.48 4.35 16.99 4.61 135.5 21.7 55.8 22.3 362.2 0.729 18.9 70.0 6.63
14018 3.90 4.89 20.00 5.29 151.5 24.1 55.7 22.2 371.1 0.779 18.9 70.0 7.80
14020 4.32 5.43 22.87 5.95 167.5 26.5 55.5 22.1 378.2 0.817 18.9 70.0 8.92
17014 3.38 4.22 17.34 3.79 187.1 20.4 66.6 22.0 331.4 0.604 17.1 85.0 6.76
17015 3.62 4.52 19.29 4.15 199.9 21.7 66.5 21.9 338.9 0.635 17.1 85.0 7.52
17016 3.86 4.82 21.25 4.51 212.7 23.1 66.4 21.9 345.4 0.660 17.1 85.0 8.29
17018 4.33 5.42 25.04 5.20 238.1 25.7 66.3 21.8 356.2 0.704 17.1 85.0 9.76
17020 4.79 6.02 28.69 5.88 263.4 28.3 66.2 21.7 364.8 0.740 17.2 85.0 11.19
17025 5.94 7.48 37.13 7.47 324.1 34.3 65.8 21.4 380.3 0.817 17.2 85.0 14.48
20014 3.92 4.90 21.57 4.62 299.2 30.3 78.1 24.9 312.1 0.540 19.0 100.0 8.41
20015 4.20 5.25 24.19 5.09 319.8 32.3 78.0 24.8 320.9 0.569 19.0 100.0 9.43
20016 4.48 5.60 26.85 5.57 340.6 34.3 78.0 24.8 328.6 0.598 19.0 100.0 10.47
20018 5.03 6.30 32.12 6.51 381.7 38.3 77.8 24.7 341.3 0.646 19.0 100.0 12.53
20020 5.58 7.00 37.27 7.42 422.6 42.2 77.7 24.6 351.5 0.684 19.0 100.0 14.54
20025 6.92 8.71 49.23 9.57 521.5 51.5 77.4 24.3 369.6 0.757 19.1 100.0 19.20
24015 4.81 6.01 30.15 5.53 514.0 40.8 92.5 26.1 296.9 0.512 19.0 120.0 11.76
24016 5.13 6.41 33.64 6.09 547.6 43.4 92.4 26.0 306.2 0.539 19.1 120.0 13.12
24018 5.77 7.22 40.60 7.19 614.1 48.5 92.3 25.9 321.4 0.586 19.1 120.0 15.83
24020 6.39 8.02 47.46 8.27 680.5 53.4 92.1 25.8 333.6 0.623 19.1 120.0 18.51
24025 7.94 9.99 63.62 10.83 841.5 65.3 91.8 25.6 355.4 0.690 19.1 120.0 24.81
24030 9.47 11.94 78.78 13.23 997.6 76.5 91.4 25.3 369.8 0.747 19.2 120.0 30.72
30020 8.02 10.09 66.02 11.90 1353.6 109.8 115.8 33.0 306.8 0.534 24.1 150.0 25.75
30025 10.02 12.60 93.33 16.16 1679.1 134.9 115.4 32.7 334.1 0.621 24.1 150.0 36.40
30030 11.97 15.08 119.18 20.19 1996.6 158.9 115.1 32.5 352.1 0.678 24.1 150.0 46.48

purlins, rails & eaves beams

06
zed purlin systems
Four structural systems are available, the Sleeved System, Double-Span Sleeved System, Heavy End-Bay System and
the Butted System. These systems allow for a flexible and efficient range of solutions to roofing supports for a wide
variety of cladding types, the major features of which are outlined below.

Sleeved single span system

This is the traditional system of single bay-length sections
with sleeves at all penultimate supports and at alternative
internal supports. The system may be used with all types of
claddings and roof pitches, within the limitations given in
this manual. Minimum number of spans is 2 and the
maximum span is 12.5m. Details are on page 32.

Sleeved double span system

Sleeves are provided at all penultimate supports and are
staggered at internal bays. The advantage is a reduced
number of erection components when compared with the
Sleeved System. Note that maximum section length is
restricted to 15m for transport and handling reasons.
Consideration should be given to handling and erection
sequence when utilising the double-span sections.
Minimum number of spans is 4 and the maximum
span is 7.5m. Details are on page 32.

Heavy end-bay single span

system
This is a highly efficient sleeved-system, with sleeves at all
supports thus allowing a form of continuous beam design.
Inner bay sections and sleeves are thinner than at the end
bay thus allowing an economic solution for long buildings.
Sleeves at penultimate supports are of the same thickness
as the outer bay purlin section. Minimum number of
spans is 4 and maximum span is 12.5m. Details are on
page 32.

Heavy end-bay double span

system
Sleeves are provided at all penultimate supports and are
staggered at internal bays. The advantage is a reduced
number of erection components. Inner bay sections and
sleeves are thinner than at the end bay thus allowing an
economic solution for long buildings. Sleeves at
penultimate supports are of the same thickness as the
outer bay purlin section. Minimum number of spans is 4
and maximum span is 12.5m. Details are on page 32.

purlins, rails & eaves beams

07
purlins, rails & eaves beams
zed purlin systems

sleeved purlin system

Single/double span lengths

Refer to pages 04 - 05 for overview of system and sleeve requirements. This system may be used with restraining or non-
restraining cladding, and may also be used to support tiled roof systems. The system may require to be used in conjunction with
sag-systems as identified for various conditions on page 09. Consideration should be given to handling and erection sequence
when utilising the double-span section.

DOUBLE SPAN CONNECTION SLEEVED CONNECTION

Butted single span system

The system is required for buildings of a single span length
and is efficient for short spans or light loadings. Butted
purlins are also useful for frames which have large clear
spans and where large frame deflections may be harmful to
continuous purlin systems. Butted purlins can be used over
supports or within the depth of the supporting section.
Maximum span is 11.4m. Details are on page 32.

Butted purlin system

This system is useful for single-span conditions, either over-supports or flush with supports. The system is also economical for
small bays or light loadings, where sleeves are not necessary.

BUTTED CONNECTION
BUTTED CONNECTION
with inset cleat for flush construction
purlins, rails & eaves beams
08
ROOF SAG-SYSTEM REQUIREMENTS

The anti-sag-system required for any given case will depend In the case of restraining type metal cladding a reduced
on the loadings, span, cladding type and roof pitch. number of rows of sag bars may be appropriate in
Different claddings provide varying restraint to the purlin particular circumstances. It should be clear that these
and it is extremely important that the roof designer should reduced systems should only be used in conjunction with
be clear on the type of roof cladding prior to selecting a the appropriate load tables which, depending on span, may
suitable sag system. For purlin design purposes within the have significantly reduced wind uplift values. The following
scope of this manual the following list outlines the main points should be considered for reduced numbers of sag
cladding types to be considered: bars:
1) Restraining type metal cladding 1. Reduced number of sag member rows applies only to
2) Non-restraining type metal cladding restrained type metal cladding.

3) Hook bolt fixed cladding 2. For roof slopes less than 3, 0-rows may be used for
spans up to 4.6m and 1 row of angle braces may be
4) Tiled roofs
used for spans up to 12.5m.

Lateral restraint is usually provided to the purlin where 3. For roof slopes between 3 - 25, 0-rows may be used
normal trapezoidal, or composite cladding is through-fixed for spans up to 7.6m and 1-row of push fit sag bars
to the purlins and where the sheets are fixed together by may be used for spans up to 12.5m.
side lap stitching. Standing seam roofs and some forms of 4. Use the reduced wind uplift capacity relevant to the
secret fix panels have fixings which allow relative number of rows of sag members selected.
movement between the purlin and the cladding and these
5. Temporary stability during erection, and other Health &
panels should be regarded as non-restraining unless used in
Safety issues should be considered when choosing a
conjunction with a suitable liner panel. A suitable liner
suitable sag system.
panel should be sufficiently robust to carry compressive
restraint forces and should be positively fixed to the purlin 6. When 0 rows of sag members are used it is
and it is also recommended that side lap stitching is recommended that one row of eaves braces and ridge
adopted to form a roof plane diaphragm. struts be used.
Some claddings, such as fibre cement panels, are fixed by
hook bolts. These claddings offer a
Table 04
reduced degree of restraint to the
purlin under wind uplift conditions Roof Sag System Details
Cladding Slope
and the limitations given in this
System Roof
section should be observed for this < 4.6m span 4.6m - 7.6m span 7.6m - 12.5m span

application. Wind uplift capacities are < 3 1 row angle braces 2 rows angle braces
reduced, and sections for these roofs
Metal
should be selected using the design 3 - 25 0 rows 1 row bars 2 row bars
Cladding
disk. (restraining type)
2 rows angle
25 - 35 1 row angle braces + diagonals
braces + diagonals
See the Tiled Roof section for
additional sag system requirements <3 2 rows angle
1 row angle braces
for tiled roofs. Metal Cladding 3 - 25 braces
(non-restraining
Sag system recommendations for type) 25 - 35 row angle braces + diagonals
2 rows angle
braces + diagonals
various roof conditions are provided
in the table right and these should be < 3 Not recommended
used as appropriate. Use of the sag
Hook-bolt 3 - 25 1 row bars 2 row bars
systems indicated will provide (restraining type)
optimum wind uplift capacity and will 2 rows angle
25 - 35 1 row angle braces + diagonals
braces + diagonals
provide a good basis for stability and
alignment during erection.

purlins, rails & eaves beams

09
purlins, rails & eaves beams
zed purlin systems

roof sag bar system

Useful for restraining metal cladding and hook bolt cladding within the limit of the table. Suitable for purlins up to 240mm deep.

Push-fit sag bars are used up to 2.0m purlin centres. Refer to Steadmans if centres are greater than 2m.
(Refer to table on page 09 for limitations of use.)

Wide flange up-slope

Use Cranked Apex Strut if slope

Push-fit Sag Bar
length exceeds 18m

Roof angle brace system

Useful for non-restraining cladding, tiled roofs and for purlins 300mm deep and steep roofs (ie. over 25)

45 x 45 x 2 angle braces may be used up to 2.0m purlin centres. Refer to Steadmans if centres are greater than 2m.
(Refer to table on page 09 for limitations of use.)

Wide flange up-slope

Cranked Apex Strut

General Notes:

Note that where sag bar numbers are reduced, within the Where sag bars or angle braces are used they should be
limits of this manual, it may be necessary to use temporary positioned at mid-span for a single row and at 3/8, 1/4, 3/8
bracing to the top flange to avoid twisting of zed purlins span for a double row, for optimum resistance to wind
during installation, particularly on roofs with shallow or uplift.
steep slopes. In the case of 0 - rows of sag bars it is
Refer to the Eaves Beam section of the manual (page 16)
recommended that eaves braces are fitted (see Eaves Beam
for general recommendations for sag systems at eaves.
section of manual - page 16) and that a ridge bar or
cranked apex strut is fitted, as in above details. Refer to the Tiled Roof section (page 14) for advice on
dealing with such heavy roofing systems.

purlins, rails & eaves beams

10
Monopitch Roofs

In a monopitch roof all the roof plane forces act

Adjustable Sag Bar
up or down the roof unlike a ridged roof which
has balancing roof load components acting
Normal Sag Bar Angle Brace
through the ridge cladding and sag system. In the
case of monopitches all roof-plane loads have to
be resisted by the purlins, claddings, cleats and sag
systems. However, with zed purlins the restraint
forces which develop due to gravity loadings act in
an up-slope direction, i.e. in opposition to the
down-slope load component so that the roof
system need only resist the net effect of these
loads. (Note that a ridged roof which is not
connected at the ridge should be considered as
two monopitches.) Eaves Brace
Diagonal ties

PLAN ON ROOF
WITH PITCH OF UP TO 6

Adjustable Sag Bar

Normal Sag Bar

Angle Brace

Diagonal ties

In effect, with roof pitches less than a critical value

Eaves Brace there is a net force acting up the slope and for
greater roof slopes the force will act downslope.

The critical angle of roof pitch depends on a

number of factors and can only be approximated
with current knowledge. As an aid to designers it
PLAN ON ROOF is recommended that diagonal ties and struts
WITH PITCH GREATER THAN 6
should be used to assist with load distribution in
these roofs. The adjacent diagrams indicate the
recommended placement of such elements for
roof pitches less or greater than 6, at which pitch
roof forces are assumed to be approximately in
balance.

Note: Anti-Sag bars (number of rows and type) to

be taken from the table on page 09.

purlins, rails & eaves beams

11
purlins, rails & eaves beams
zed purlin systems

Steep Pitch Roofs Diagonal Ties

Where roof slopes are greater than 25 but no

greater than 35 the following points should be
considered:

between diagonal ties

1. Use angle braces and cranked apex struts to

12m maximum
replace normal sag bars. (Minimum number of
rows provided on page 09).

2. Use diagonal ties at intervals of no more than

12m on the slope length, to assist with
absorption of roof plane forces.

3. Reduce purlin capacity by including down-slope

load component. This is most simply achieved
by using the design program which
Diagonal Ties
automatically includes down-slope components
25 minimum
for pitches greater than 25.

between diagonal ties

4. Check purlin cleats for down-slope load

12m maximum
component, use heavy duty cleats if required. Angle brace

Purlins

Shallow Pitch Roofs

For very flat roofs, say below 3 , particularly if the

span exceeds 6m or if non restraining cladding is Eaves beam
used then, in addition to the sag systems indicated
in this manual the use of purlin reversals is highly PLAN ON STEEP ROOF
recommended to balance the extensive up-slope
restraint forces which develop due to the zed
shape. This is particularly important in the case of
any long slopes or monopitches and there should
be slightly more zeds pointing up the slope than
down slope.

Alternative purlins reversed in direction

purlins, rails & eaves beams

12
Long Roof Slopes

For roof slopes in excess of 20m in length (on the slope), and with a pitch of greater than 3 it is recommended that each sub-
length is divided into 20m (maximum) length sections and that each section is stiffened in the roof plane by the addition of angle
struts and diagonal ties, as indicated. For long roofs with a pitch below 3 a similar system should be adopted but the diagonal
ties should be acting in the opposite direction.

Adjustable sag-bar
Diagonal tie cleat

Diagonal ties

Adjustable sag-bar Angle brace

Curved Roofs

Curved roofs become flat near the apex and it is recommended that in the near-ridge zone, when the tangent to the roof
cladding is less than 3, then purlin reversals should be adopted as in the diagram. (ie The near-ridge zone is treated as a shallow
pitch roof.)

Note: Anti-sag bars (number of rows and type) to be taken from the table on page 09.

Adjustable sag-bars
Apex strut

Alternative purlin directions reversed when roof tangent is less than 3

purlins, rails & eaves beams

13
purlins, rails & eaves beams
zed purlin systems

Angle braces at 2.5m

Tiled Roofs
maximum centres

Cold rolled purlins are increasingly being used to

support tiled roofs. This application is particularly
suitable for Zeds which have principal axes inclined
Fix cleat to rafter
from the web axes and which consequently have
upslope restraint forces acting in opposition to the
downslope load component thus minimising the
large downslope forces inherent to this form of
roofing.

Two types of application are common for use with

30 min.
natural slate or concrete tile materials:

1. Tiles may be fitted to timber battens nailed to

s
re
m

nt
00
counter battens which are screw fixed to the

ce
18

um
top flange of the purlins.

im
Note that the diagonal braces

ax
m
2. Tiles may be fitted to timber battens fixed to a should be placed at regular
positions down the roof, at
proprietary metal liner tray.
centres not exceeding 5.4m for
roof pitches up to 25 and not
Some special considerations are required when exceeding 4m for roof pitches ROOF WITH BATTENS
above 25. & COUNTER BATTENS
designing a tiled roof:

1. Purlins should be limited to a deflection of

span/300 in the web plane to avoid visible sag.

2. Where a building is ridged, when timber Metal liner tray

counter battens are used they should be bolted Note that diagonal braces
together at the ridge to balance the down- should be placed at regular
slope forces so far as is possible. positions down the roof, at
centres not exceeding
3. Any timber counter battens fixed up the slope 5.4m.
of the roof should be attached to each other
with metal straps to assist in carrying the
tensile forces which will develop in the roof.

4. The Sag-System must be sufficiently

robust to handle the down-slope load
component, and the purlins require 30 min
to be designed for two-way bending,
Fix cleat
as in the steep roof section above.
to rafter
Use angle braces at sag member positions,
m

s
re
m

nt
00

in conjunction with diagonal ties. If loadings

ce

Angle braces at 2.5m

18

um

are substantial the diagonal ties should be maximum centres

im
ax

fixed directly to the steel supporting rafter.

m

5. Cleats should be checked for their ability to

handle the large down-slope forces, use heavy
ROOF WITH LINER TRAY SYSTEM
duty cleats if necessary.

purlins, rails & eaves beams

14
tiled roofs

No load tables are provided for this application and Timber sections bolted together
assistance in particular situations can be obtained by at ridge

discussing the requirements with Steadmans, or the design

program can be used if the roof pitch exceeds 25.

Some typical details are provided, for the purpose of

general guidance in the design of these roofs.

Note that in addition to the use of natural materials

Steadmans offer the unique Meta-Slate roof system which
combines the natural look of slate with the lightweight
construction of pressed steel construction (see separate
technical brochure). Purlins for this application should be
Heavy duty ridge
designed as for non-restraining metal cladding. channel
Angle braces

Cantilever Purlins

These are frequently required to form gable overhangs, with or without deep soffit framing. Performance depends on the purlin
section and on the backing span. The purlin section should be no less than that required for the adjacent main span, selected in
the absence of the cantilever loading. Where deflections are critical the purlin section should be chosen accordingly, following the
guidance below. Purlin sections should be confirmed by evaluation, considering the following parameters:

1. Purlin section must be continuous over the gable frame.

2. Maximum cantilever span is 30% of the backing span, but not greater than 3m.

3. Bottom flange should be restrained by cladding or by

restraints at centres not exceeding the lesser of 2m
and ten times the section depth.

4. Purlin ends should be braced with

cleader angles top & bottom or with an
angle brace providing torsional
restraint, placed near the end. Restraint
should be carried across the ridge where
applicable.

5. The factored BM at the support should not exceed

the purlin moment capacity for gravity or wind uplift
effects (Mc in the section property table). Diagonal
brace
6. Tip deflection should be limited by increasing the
purlin section, if required. Angle braces
(alternatively top
7. Where the cantilever span exceeds 1.0m a diagonal
& bottom cleaders)
tie should be fitted as in the sketch. This is particularly
important in the case of steep roofs, monopitches and
Ca
nt

heavy claddings.
ile
ve
rs
pa

8. Special care is required with heavy roof claddings or

n

tiled roof systems. Refer to Steadmans for advice in

particular cases.

purlins, rails & eaves beams

15
purlins, rails & eaves beams
eaves beams

sections

Three depths of eaves beam are available. Folded indented roof designer is confident that the structural implications
sections with a maximum length of 10m are available in have been fully considered.
200mm and 240mm depth. A 300mm deep Cee section
eaves beam is available up to a span of 12.5m to Eaves braces perform the following functions:
complement the 300 series of purlin sections. These are
1. Reduce the horizontal design span for side wind.
available in the thicknesses indicated. Eaves beams are
usually single spanning but the 200 and 240 series may be 2. Assist with dispersing horizontal wind loads into the
supplied as double-spanning up to a 5m span and the 300 roof diaphragm.
series can be double-spanning up to a 7.5m span.
3. Reduce any twisting due to eaves gutters and with
The 300mm deep eaves beams may be optionally used with erection of roof cladding.
counterformed holes and countersunk bolts, with either
The eaves beam design tables and design disk are based on
countersunk holes or spacer plates as indicated.
the assumption that the top flange is fully restrained by the
It is recommended that at least one row of eaves braces roof cladding and care is required where this is not the
should be adopted, even where a zero row of sag bars is case, for example where standing seam or clip-fixed
used with the purlins. Additionally the number of rows of cladding are used without a suitably stiff liner panel. Most
eaves braces should not be less than the number of rows of design situations can be handled using the design disk but
sag bars for purlins, as in the table on page 09, or as due to the many conditions that may be met in practise,
selected by the designer to suit any particular design. section properties are provided to assist the designer with
Removal of eaves braces should only be carried out if the any individual designs that may be required.

200 EAVES BEAM SERIES 240 EAVES BEAM SERIES 300 EAVES BEAM SERIES
15 15
41
30

30
15

15
200

110

70

counterformed
300

218
150

110
240

holes shown
15
30

20

15

80
41
30

20

19

Rake to flanges available from 0 to 35

90 95
(above 35 contact Steadmans)

Table 05: Sections

Section Weight (kg/m) Sxe (cm3) Ixx (cm4) Zyy (cm3) Iyy (cm4) Ryy (mm) Poc
EB200/16 5.10 35.48 373.8 8.66 44.9 26.3 350
EB200/20 6.35 47.68 487.7 10.64 55.1 26.1 350
EB200/25 7.90 61.70 620.3 13.02 67.3 25.9 350
EB240/25 9.08 83.09 1009.3 15.80 94.1 28.5 350
EB240/30 10.84 101.18 1218.0 18.58 110.6 28.3 350
EB300/30 11.97 134.59 2026.0 22.32 159.0 32.3 329

purlins, rails & eaves beams

16
typical eaves beam details

EAVES BRACES FOR ROOF SLOPE LENGTH UP TO 18M

Push-fit Push-fit
sag bar sag bar
200 & 240 SERIES 300 SERIES

EAVES BRACES FOR ROOF SLOPE LENGTH GREATER THAN 18M

Adjustable Adjustable
sag bar sag bar
(or angle brace) (or angle brace)
200 & 240 SERIES 300 SERIES

typical connections to column heads

6mm thick packing

plate with 28mm dia
holes for M12
countersunk bolts

200 & 240 SERIES 300 SERIES

OUTSTAND CONNECTIONS

purlins, rails & eaves beams

17
purlins, rails & eaves beams
eaves beams

typical connections to column heads

FLUSH COLUMN
CONNECTIONS

200 & 240 SERIES 300 SERIES

connections between eaves beams and rail struts

6mm thick packing plate

between EB and cleat

6mm thick
stiffening cleat
6mm thick stiffening cleat.
(Allow additional 6mm reduction
in any eaves braces connected to
same cleat)

2 x M12 bolts 2 x M12 bolts

Rail strut Rail strut

200 & 240 SERIES 300 SERIES

purlins, rails & eaves beams

18
zed and cee sheeting rails
Sheeting rails may be selected as either Zed profile or Cee profile sections. These are formed from the same coils and
are each available in the same depth and thickness range. Cees may be substituted for Zeds at window and door
framing and at composite cladding joints, etc.

The two types of section can be mixed on the same rail line though it is not possible to locate sleeves on the junction
between Zeds and Cees. Each system should be regarded separately between such junctions when considering load
capacities.

Three basic systems are given in this manual, i.e. the Sleeved System, the Butted System and the Double Span (Brick
Restraint) System. A Heavy End-Bay System can be used though in practice this may be hampered by interaction with
door standards, etc, and the designer will require to exercise caution if this system is used (and indeed may require to
anticipate the possibilities of future alterations to the wall structure). The design disc provides a method of load
assessment for this system.

Sleeved system
This is a system of single bay length sections with sleeves at
penultimate supports and at alternative internal supports.
Minimum number of spans is 2 and the maximum span
is 12.5 metres. Details are on page 32.

Butted system
This is a single span system. The system is required for
single bay length rails and is efficient for short spans or
light wind loadings. Sections can be fitted running past the
supports or may be within the depth of supporting
sections. Maximum span is 11.4 metres. Details are on
page 32.

Double span system (brick

restraint)
This is a relatively stiff system intended for use as brickwork
restraints, or as window framing. Minimum number of
spans is 2 and maximum transport length of section is
15 metres thus maximum span is 7.5 metres.

Use double-span sections for the full length if the wall has
an even number of bays and use a triple-span rail, ie
double-span plus a sleeve, if an odd number of bays.
Section thickness may require to increase for the triple-span
case to compensate for the reduced stiffness, when DESIGN DISK ALLOWS FOR
compared with the double span system. VARIATION IN DEFLECTION
Details are on page 32. FACTOR

purlins, rails & eaves beams

19
purlins, rails & eaves beams
zed and cee sheeting rails

Sleeved Rail System

Typical connections are illustrated for sleeved joints for both Zed and Cee Sections.

Note that the sleeves for the Zed System may be the same thickness as the rail section but sleeves for the Cee System are
provided in one standard thickness for each rail depth.

A B

Sleeve
Rail

Sleeve

Rail

ZED RAILS CEE RAILS SECTION AT SLEEVED CEE

SECTION RAIL

Table 06

Thickness for
Rail Depth Dimension A Dimension B Dimension C Dimension D
Cee Sleeve
ZED RAIL FLANGE TO THE
140 148 147 146 60 2.0
CLADDING MUST TOE UPHILL
170 178 177 177 60 2.5
FOR FIBRE-CEMENT, HOOK
200 208 207 207 70 2.5
BOLT FIXED
240 248 247 248 70 3.0
300 308 307 308 90 3.0

purlins, rails & eaves beams

20
Butted & Double Span Rail System

The connections for these two systems are identical except that
the Butted System has a butted connection at every frame and
the double-span system has a butted joint at alternative
connections and is continuous over intermediate supports.

Rail

ZED RAILS

Rail

CEE RAILS

Typical Brick Restraint Details

STEEL TIE FIXING
Proprietary steel straps
Typical details are indicated for illustration. The
fixed to Engineers
brickwork designer is responsible for design of the
requirements
blockwork to rail connections and should select
rails on the basis of a suitable deflection limit.

A deflection limit of span/300 is commonly

employed and the design program defaults to that
limit for double span systems. The user may alter
this as required.

STEEL STRAP FIXING

Steel straps and ties to
Engineers requirements

purlins, rails & eaves beams

21
purlins, rails & eaves beams
zed and cee sheeting rails

Sheeting Rail Sag-System Requirements

The user should note that it is assumed in the development of details and load tables that wall claddings will provide a diaphragm
action and will be positively fixed to the rails, thereby eliminating vertical bending in the rails. Any claddings which do not meet
these criteria should be referred to Steadmans, or the program may be used with the cladding weight included.

The number of rows of sags members for normal use is provided in the table, shown below for restraining-type metal cladding
and fibre-cement cladding. The table also provides limiting dimensions for a number of cases.

Less limiting conditions can be applied for support of restraining type metal cladding, in certain cases. Where the cladding weight
can be carried by floors, brick wall heads or eaves beams or by diaphragm action, and where the reduced wind load capacity is
acceptable then 0 rows of sag bars may be adopted up to a 6.3m span, and a single row may be used up to a 7.6m span. In the
case of 0 rows being adopted then temporary supports may be required to prevent sag in the rails during erection.

The usual system of rail restraints comprises the use of 45 x 45 x 2 angle section rail struts, with diagonal ties, as indicated on the
next page.

Table 07: Limiting Dimensions for normal conditions

Cladding Number of rows of sag members

Case
type 0 1 2 3

Maximum span for

Restraining 3.0m 6.3m 10.0m 12.5m
Normal Sag System
type metal
cladding Maximum panel height n/a 10.0m 10.0m 7.5m
/set of diagonal braces

Maximum span 2.4m 5.1m 7.6m 10.0m

Fibre-cement
cladding Maximum panel height n/a 7.0m 7.0m 6.0m
/set of diagonal braces

Additional Notes:

1. In the case of multiple rows of rails the maximum 4. Advice should be sought from Steadmans when
number of rails per set of diagonals should be limited to supporting any special claddings, such as clip fixed,
8. which offer less restraint and reduced diaphragm action.

2. For double-row sag systems in walls the sag members 5. Support cleats should be checked for their capacity to
are placed at 1/3 spans for a uniform appearance. For handle wall cladding weight where this exceeds 13kg/m2
triple row systems place sag members at 1/4 spans. or where flat plate cleats are used. Similarly if wall
glazing or other deflection sensitive claddings are used
3. For spans in excess of 10m use heavy duty angular
then the designer should confirm that the cleats have
diagonal ties in place of tie wires.
adequate bending resistance and consideration should
be given to using heavy duty angular diagonal ties in
such conditions.

purlins, rails & eaves beams

22
Sheeting Rail Sag Systems

* Note that for restraining type metal cladding up to 10m

high the diagonal ties may be removed if the rail struts are Tie wire
taken up and securely fixed to the underside of the eaves
beam, provided the eaves beam is designed to carry its
tributary weight of wall panel. The fixing to the eaves beam
should incorporate a stiffening cleat for wall heights greater
than 4m, or with heavy claddings.

(See Eaves Beam section on page 16 for details.)

Outer flange

DIAGONAL TIE FIXING TO RAIL STRUT

Eaves Beam span

3 span 3 span span
1/ 1/ 1/
3

* * *

Rail struts

Diagonal ties
25 minimum 25 minimum

SINGLE ROW STRUT SYSTEM DOUBLE ROW STRUT SYSTEM

span
4 span span
1/ 1/ 1/ span 1/ span
4 4 4

* * *

Rail struts
DIAGONAL TIES SHOULD
BE ANCHORED TO THE
CLEAT BOLTS NEAREST
THE COLUMN FLANGE
Diagonal ties
25 minimum

TRIPLE ROW STRUT SYSTEM

purlins, rails & eaves beams

23
purlins, rails & eaves beams
zed and cee sheeting rails

Horizontal Wall Cladding Eaves Beam

Requirements or structural
member
Horizontal cladding is often used in conjunction with cold
rolled rail systems. Some examples are provided to assist the
Zed or Cee
designer in deciding suitable cladding support. In all cases vertical rails
the eaves beam or structural top member should be
checked for horizontal wind loading, in addition to any
vertical loading. Zed or Cee rails

Type 1
Eaves Beam designed for wall cladding weight TYPE 1
The number and position of vertical rails will depend on
cladding requirements. Horizontal rails should generally be
selected as for vertical claddings, but load capacity may
require to be reduced when the spacing between vertical
rails exceeds 2 metres. (Refer to Steadmans.)

Eaves Beam
Type 2 or Top Rail
Eaves member not designed to carry wall cladding
weight
Zed or Cee
Horizontal rails should be selected as above. The minimum vertical rails
number of sets of diagonal ties should be as given in the
table on page 22. Vertical rails should be spaced to suit the
Zed or Cee rails
cladding but should also satisfy the minimum angle shown
for diagonal ties. Load capacity for horizontal rails may 25 minimum

require to be reduced when the spacing between vertical

rails exceeds 2 metres, as noted above. Support cleats
TYPE 2
should be checked for their capacity to handle wall
cladding weight where this exceeds 13kg/m2 or where flat
plate cleats are used.

Type 3
Vertical Rail System
Structural Top Rail or
Vertical rails should be selected as for a Butted rail system Member Cleader
of the same span as the vertical distance between top and or Eaves
bottom supports. Use horizontal struts at the minimum Beam Zed or Cee
vertical rails
number of locations as recommended for sag members
for the same span. The top member may be a structural
section or eaves beam depending on the nature of Rail
Fix to floor or
Struts
construction. The base of the posts may be fixed to the structural
member at
floor or a structural section can be used. Top and bottom base
members must be designed for horizontal wind loading as
dictated by the construction details.
TYPE 3

purlins, rails & eaves beams

24
Fire Rated Boundary Walls

Under boundary conditions it is required to provide walls

with a fire rating. In these cases the fire rating is provided
by the wall cladding and insulation, which are taken to be
independent of the rail system in a fire situation. However,
BUTTED RAIL
rails are required to have slotted end-holings to reduce
CONNECTION
buckling due to the significant thermal expansion during AT FIREWALL Use 14mm dia holes in rail
fire conditions. Connections utilise combustible washers as and 14mm dia x 45 slots
in cleat and special sleeve
indicated, to facilitate these thermal movements, whilst
providing for normal rail performance during non-fire
conditions. (Some approving authorities also require that
the eaves beam be fire protected.)

The Steadmans fire rail system has been developed to

provide a suitable facility for expansion through slotted
holes on the sleeves and cleats. Thus, the system can be
used for sleeved and butted rails without limiting the joint 33 33
positions, provided the slotted cleats and sleeves are 70 70
adopted, all as indicated here and in the detailing section.
The system may be used for spans up to 10m.

SEE DETAILING SECTION FOR

DETAILS OF SPECIAL SUPPORT
SLEEVED CLEAT REQUIREMENTS
CONNECTION
AT FIREWALL
Use 14mm dia holes in rail
and 14mm x 45 slots in
cleat and special sleeve

33 33
*300 series has 12 bolts in sleeve
std* 70 70 std* See page 34 for details

M12 Gr 8.8 bolt

Details are shown here for zed rails but
Steel Washer
they apply equally to Cee section rails.
Rail
See page 34 for detailing information.
Combustible Nylon Washer

ENLARGED BOLT DETAIL

SHOWING COMBUSTIBLE
Steel Washer PLASTIC WASHER
Cleat (or sleeve)

purlins, rails & eaves beams

25
purlins, rails & eaves beams
additional details

TYPICAL ZED SECTION DETAILS (CEE SECTIONS SIMILAR)

80 40 40

37 37

42

40
8

Cleader Cleader
6 varies
Angle Angle
(not to exceed 3 x section depth)
GABLE PURLIN DETAIL
ALTERNATIVE GABLE PURLIN DETAIL
(or can use a sleeve at extendable gable)
80
6 varies

42
Rail end
cleat if
required A

40
8

80
70 6 varies

42
Welded or bolted
A
bracket
42 A 40
40
8
CORNER RAIL CONNECTIONS 32

Table 08 3mm galv.

steel plate
Depth A

140 58
170 88
42 A 40
200 118
240 158
ALTERNATIVE CORNER RAIL CONNECTION
300 218

Dimensions in mm

purlins, rails & eaves beams

26
Parapet Framing

Steadmans produce a variety of zeds and cees

which can provide a flexible range of solutions
Adjustable
to parapet framing. Sag Bar
Angle braces
Parapet posts may be fabricated from standard
Cee sections bolted together to form double-
cees at rail positions and at centres not
exceeding 1500mm. (Use the thickest section
available for the post depth used, to assist
with absorbing bolt tension at the
connection.)

Use posts of same depth as rails for flush and

convenient connections.
500mm
min

Posts may be bolted to columns via 8mm

packer plates. Connection should be designed
to suit height of parapet but height between
pairs of bolts should not be less than 500mm
Steadmans column head ties
and use backing plates at the flange when 8mm steel packers (Not supporting gutter in this
bolt tension exceeds the flange capacity. example)

Alternatively, for higher wind loadings it may

be preferred to weld 6mm fin-plates to the EXAMPLE WITH POST BOLTED TO COLUMN FLANGE
column flanges and to bolt the cees sections
on either side.

Particular attention should be paid to wall sag

systems to remove sag, when gutters are
supported from the rails.

Gutter supported on
column head ties
500mm
min

6mm welded Welded angle braces

fin plates

EXAMPLE WITH POST BOLTED TO FIN PLATES AND GUTTER SUPPORTED ON HEAD TIES

purlins, rails & eaves beams

27
purlins, rails & eaves beams
additional details

Valley Beam Details

Cold rolled cees in back-to-back

configuration are commonly adopted for
support of valley gutters and/or valley
column ties. Cees should be bolted
together in pairs on the standard gauge
lines at ends and at centres not exceeding
1500mm.

Section properties of selected double-Cee

Steadmans
beams are provided to assist with design.
column
Design should be carried out to head ties
BS 5950-5:1998 or by reference to
Steadmans.

HEAD TIE DETAIL WITH NO GUTTER SUPPORT

Adjustable sag bar

Angle braces

Steadmans
column
head ties

HEAD TIE DETAIL WITH GUTTER SUPPORTED BY HEAD TIES

Table 09: Section properties for selected double-cee sections

Section Weight (kg/m) Sxe (cm3) Ixx (cm4) Ryy (mm) Rxx (mm) Mc (kNm)
2@C170/18 8.94 59.16 508 29.6 66.8 18.86
2@C200/18 10.06 76.58 778 30.8 77.9 24.26
2@C240/20 12.78 114.22 1384 31.8 92.2 35.48
2@C300/25 20.00 224.10 3405 40.1 116.0 69.50
2@C300/30 23.94 268.90 4046 40.0 115.0 88.48

purlins, rails & eaves beams

28
 Double
Cee head
Door and Window Framing beam

Cee Sections are particularly suited for trimming door and window
frames.

Counterformed holes are available as an option, though the use of

timber packers at windows and door frames are recommended in order
to take up tolerances and slight misalignments and in these cases normal
or thin-head bolts may be simpler and more economical.

If cold rolled sections are used as framing for overhead doors, then:

1. Check that eaves beam can carry any horizontal wind forces, add
eaves braces or a double-Cee head section, as required.
Single Cee
2. Confirm with door supplier that the thin section can carry local forces
door
from the springs and rollers. trimmer

3. Use maximum available thickness for section depth utilised.

4. If impact damage is likely then add bollards to protect steelwork and Single Cee
cladding. door post

TYPICAL DOOR FRAMING DETAILS SECTION THROUGH

TYPICAL OVERHEAD DOOR

Standard
cleats

Timber spacers
fixed to rails TYPICAL WINDOW SECTION
(optional)

Standard cleats
bolted to sub-structure

purlins, rails & eaves beams

29
purlins, rails & eaves beams
additional details

Suspended Services & Point Loads

Services are commonly suspended from the purlins, such For heavier point loadings a steel framework should be
loads varying in nature and magnitude. This section gives adopted as shown below. Maximum point loads applied to
guidance as to accommodation of the point loadings the purlin for this system should be determined in
involved. agreement with Steadmans.

The table below gives the maximum single point load

(unfactored) value for typical light loading applications. For Table 10: Maximum value for point loads
use of this table three conditions must be satisfied; for loading cases A and B

1. Load centres to be not less than 500mm, Thickness Type A Type B

2. Purlin must be selected for a total UDL not less than the 1.4 - 1.6 10kg 20kg
sum of the dead load + imposed load + a service load 1.8 - 2.0 15kg 30kg

not less than the UDL value which would give the same 2.5 - 3.0 20kg 40kg

mid span BM as the point loads on a simple beam of the

same span,

3. If roof slope exceeds 12 then reduce allowable load

linearly to a value of 50% the tabulated value, at a
maximum slope of 25.

CASE B - LOAD
SUSPENDED FROM BOTTOM CASE A - LOAD
FLANGE OR WEB LINE SUSPENDED FROM PURLIN LIP

=
=

TRIMMING DETAIL FOR

Cee trimmers
HEAVIER SERVICE LOADING
(subject to purlin capacity
limitations) Hangers bolted to trimmer webs

purlins, rails & eaves beams

30
Suspended Ceilings

Cold rolled sections are increasingly being used as suspended ceiling supports. Support may be provided by either zeds or cees,
provided that sections are properly restrained against twisting and buckling. Sections may be used over or under supports
depending on individual circumstances.

Typical details are provided for illustration purposes. Steadmans may be contacted for advice and section design for any
application or alternatively use the simplified method provided below.

VIEW ON UNDERSLUNG SLEEVED ZED SYSTEM

Standard angle braces

TYPICAL SECTION THROUGH ZEDS SHOWING ALTERNATE DIRECTIONS OF SECTIONS

Notes:

1. Torsional and lateral restraint should be applied at 4. Whether zeds or cees are used they should be used in
supports (cleats) and at mid-span for spans up to 6.1m opposing pairs, as illustrated, to minimise any twisting
and at third spans for spans up to 10m. Such restraints effects.
should be tied back to a suitable anchorage to prevent
5. Sections may be selected from the load tables in the
lateral movement of the support grid.
normal way but the tabulated gravity load capacities
2. Select sections of a suitable stiffness to provide a should be reduced by 50% to allow for the reduced
deflection not exceeding the limits provided by the restraint. (No reduction required for deflection controlled
ceiling supplier (usually span/240 to span/360). values.)

3. Zeds may be single spanning or may be sleeved, if details Alternatively, use the design program with non-restraining
suit. Cees are generally used as single spanning sections. cladding.

purlins, rails & eaves beams

31
purlins, rails & eaves beams
detailing information

zed purlin and rail hole punching details

ZED SECTION SLEEVES
HEAVY END-BAY SYSTEM
With this system, heavy gauge sections are used in the end C

bays and at penultimate support sleeves. Care must be taken 40 40

to properly identify components on site to avoid 40

misplacement. Usually end-bay purlins can be detailed to be

300
A
different from inner-bay sections but as sleeves look similar at 42
6
all positions consideration may be given to using heavy gauge
sleeve sections at all supports to avoid wrong positioning. 25 150 B 80 B 150 25

Sleeve for 300 Series

Table 11
C
Depth A B C 40 40

140 58 235 600 40

DEPTH

170 88 285 700 A

200 118 335 800
42
240 158 435 1000 6
Dimensions
300 218 435 1300
in mm
25 B 80 B 25
Note: All holes 14mm dia for M12 bolts, minimum grade 8.8 use a
Sleeve for 140, 170, 200 and 240 Series
washer under all bolt heads and nuts in contact with sections or sleeves.

ZED PURLINS & RAILS

L=section length

3 3
Wide Flange
42
A

40
8

37 B 150 150 B 37

Single spans Sag bar holing.

Purlins: Use holing at midspan for single row, at 3/8:1/4:3/8 span for double row.
Rails: Use holing at midspan for single row, at 1/3 spans for double row, 1/4 spans for triple row.

* Additional holes required for 300 series sleeves only.

L L

3 3
40 40 Wide Flange
42
A

40
8

37 B 150 80 150 B 37

Double spans

purlins, rails & eaves beams

32
cee rail hole punching details

Table 12

Sleeve Note: All holes 14mm dia for M12

Rail Depth A B C D E F
Thickness
bolts, minimum grade 8.8. Use a
140 2.0 58 235 600 146 44.0 150
170 2.5 88 285 700 177 44.5 180.5 washer under all bolt heads and nuts
200 2.5 118 335 800 207 44.5 210.5 in contact with sections or sleeves.
240 3.0 158 435 1000 248 45.0 251
300 3.0 218 435 1300 308 45.0 311
Dimensions in mm

CEE SECTION SLEEVES

C C
40 40 40 40

E E
D A F D A F

E E
48 48
25 150 B 80 B 150 25 25 B 80 B 25

Sleeve for 300 series Sleeve for 140, 170, 200 and 240 series

CEE PURLINS & RAILS

L=section length

3 3

41
A

41
7

37 B 150 150 B 37

Single spans Sag bar holing at midspan for single row, at 1/3 spans for double row. 1/4 span for triple row.

* Additional holes required for 300 series sleeves only.

L L

3 3
40 40

41
A

41
7

37 B 150 80 150 B 37

Double spans

purlins, rails & eaves beams

33
purlins, rails & eaves beams
detailing information

fire wall rail hole 25 150 B 70 70 B 150 25

punching details 33 33

ZED SECTIONS
Table 13 A

Depth A B C
48
140 58 235 660
170 88 285 760 Sleeved Zed rail connection
200 118 335 860 for 300 series
240 158 435 1060
300 218 435 1360 Dimensions in
mm C

70 70 25 B 70 70 B 25

33 33 33 33

A A

40
8 48

Butted Zed rail Sleeved Zed rail connection

connection for 140 - 240 series

C
Cee sections
These details should be used in conjunction 25 150 B 70 70 B 150 25

with information on page 25 and with cleats 33 33

as detailed on page 35.

48

Sleeved Cee rail connection

for 300 series

C
70 70
25 B 70 70 B 25
33 33
33 33

A
A

41
7 48

Butted Cee rail

Sleeved Cee rail connection for
connection
140 - 240 series

purlins, rails & eaves beams

34
standard cleats for purlins & rails

Standard formed cleats - finish: black mild steel

Note for formed cleats:

25 80 25 25 80 25 6
1. Holes in cleat upstand
are 14mm dia for M12 25 25
grade 8.8 bolts.

2. Holes in base plate for

bolt-on cleats = 18mm A A
dia.

3. For very heavily loaded,

steep roofs or heavy 48 48
wall claddings,
Steadmans can on 130mm x 6mm flat bar 30 70 30 40 30
request provide heavy
130 70
duty cleats reinforced
with welded stiffeners. WELDED CLEATS BOLT-ON CLEATS

Fire wall cleats - finish: black mild steel

30 70 70 30 t 30 70 70 30 t

25 14mm dia x 45mm

slots in long leg 25

18mm dia x holes 6mm welded

in short leg stiffener
A
A

48
48
35 35 40 30
35 35 40 30

200 70 200 70

NORMAL FIRE WALL CLEATS HEAVY DUTY FIRE WALL CLEATS

Table 14

Note for fire wall cleats: Section Depth A

1. t = 6mm for 140 to 200 series 140 58
t = 8mm for 240 and 300 series 170 88
200 118
2. It is recommended that heavy duty cleats are used for all 300 series connections 240 158
Dimensions
and for heavy cladding systems. 300 218
A in (mm)

purlins, rails & eaves beams

35
purlins, rails & eaves beams
detailing information

Anti-SAG SYSTEM COMPONENTS

L

L Roof angle
e
f lin
Roo

PUSH-FIT SAG BAR

H

L 50

CRANKED APEX STRUT WITH PUSH-FIT SAG BAR

ADJUSTABLE SAG BAR

L
50 L 50

e Roof angle
f lin
Roo
DOUBLE-ADJUSTABLE SAG BAR 24

X
H
50 L 50 24
12mm dia threaded bar

THREADED TIE ROD CRANKED APEX STRUT WITH ADJUSTABLE SAG BAR
OR WITH ANGLE BRACES

L
L 24
e
f lin
e f lin
Roo Roo X
24

24 24

Y Y
24 Roof angle 24 Roof angle

EAVES BRACE WITH PUSH-FIT SAG BAR EAVES BRACE WITH ADJUSTABLE
SAG BAR OR WITH ANGLE BRACES

Note: All holes 14mm dia for M12 bolts, minimum grade 8.8
General Notes:
Note that the dimension X refers to the purlin and Y refers to the Eaves Beam. Anchor cleats should be placed at the holes above the
rail strut end cleat (and nearest the sheeting) for a single sided diagonal tie position and under the rail strut cleat for a double sided
diagonal tie position. The tie top fixing should be bolted to the cleat hole nearest the column.

purlins, rails & eaves beams

36
cleats

Table 15

3 Section
21 A 21 Depth A G

140 58 110 Cleats fabricated

170 88 110 from 3mm Galv Z35.
30 200 118 110 Holes 14mm dia for
37 240 158 125 M12 grade 8.8 bolts.
300 218 135
variable

G
Dimensions in mm

LONG TRIMMER CLEAT 30 30

40 30

25

3 40
21 A 21
25
14mm dia holes

30
37 43 70

6
70 x 70 x 6mm angle

SHORT TRIMMER CLEAT 30 30 STAY CLEAT

30

30

38 22 14mm dia holes

60 x 60 x 2mm zinc plated steel

RAIL END CLEAT

purlins, rails & eaves beams

37
purlins, rails & eaves beams
detailing information

miscellaneous componentS
30 30

28

28

Galv 6mm thick

plate 36mm dia holes
Rail closer from 45 x 70 Galv angle x 2mm thick
PACKER PLATE AT
COUNTERFORMED HOLES RAIL CLOSER DETAIL
24 A 24

24

80

24

Galv steel 3mm

thick 14mm dia holes 45 x 45 x 2mm Galv stay
Welded-on Cleat
(not by Steadmans)
RAIL CORNER JOINING PLATE

RAFTER AND COLUMN STAY DETAIL

Table 16
Depth A
140 58 Note: All holes
170 88 14mm dia for M12
200 118 bolts, minimum
240 158 grade 8.8
300 218 (plated finish)

Dimensions in mm

24
A
Stay cleat
24
45 x 45 x 2mm Galv angle

ALTERNATIVE STAY DETAIL(RAFTER AND COLUMN)

STANDARD ANGLE BRACE AND RAIL STRUT

purlins, rails & eaves beams

38
custom sections

Steadmans have the ability to brake-press a wide variety of customised sections to suit customers individual
requirements. Pressings may be up to 10m long and up to 3.0mm in thickness.

Some typical examples are indicated to illustrate the flexibility of this approach.

SHEET PROFILES TO MATCH OBSOLETE CLADDING

COMPOSITE VALLEY GUTTER

Bonded Polyisocyanurate
Foam Core: 30mm, 40mm
or 50mm thick.

CUSTOM SECTIONS

STRUCTURAL
GUTTER

TYPICAL VALLEY GUTTER

TYPICAL BOUNDARY WALL BOX Available up to
GUTTER
1250mm in girth.

purlins, rails & eaves beams

39
purlins, rails & eaves beams
technical support

Steadmans offers comprehensive technical brochures NBS specifications

technical support to designers and NBS Plus is a library of
Our technical brochures contain all
contractors working with Steadmans technical product
the performance, design and sitework
products and accessories, including: information written in
information specifiers require to
technical brochures and data NBS format, linked to
select, incorporate and specify
sheets NBS clauses and clause guidance.
Steadmans products into a project.
CAD details With NBS Plus, specifiers can select
All our brochures are available in PDF products quickly and accurately then
copies of test certificates
format for immediate download from drop the product information directly
loading calculations into a specification.
our web site. Printed copies are also
NBS Specifications available upon request. NBS clauses for AS twin skin roof and
design and installation guidance wall systems and other Steadmans
products are now available for NBS
project showcase and case studies CAD details subscribers. To access NBS Plus, go to
All the design details contained in our our web site and click on the link on
All the support information above can the home page.
technical brochures are being made
be downloaded direct or requested
available for free in AutoCAD 2004
from our website.
format for incorporating into project design & installation
www.steadmans.co.uk designs. guidance

To access the current range of details, Design and installation guidance for
To contact our Technical Department: the AS35 system, Single Skin system,
go to the Support section of our web
tel: 01697 478 277 Twin Skin system, Meta-Slate &
site and select the Downloads link.
fax: 01697 478 530 Meta-SlatePlus systems are contained
There is no need to register to use in the individual technical brochures
email: [email protected]
our details. and manuals.

To contact our Sales Department: These can all be downloaded from

test certificates the Literature section of the
tel: 01697 478 277
Copies of test certificates are Steadmans web site.
fax: 01697 478 530
available upon request from our
email: [email protected] In addition, we also provide
Technical Department.
installation instruction sheets for
various applications. Links for these
loading are located on the Downloads page
calculations in the Support section of our web
For loading calculations contact our site.
Technical Department - see details
opposite.

purlins, rails & eaves beams

40
references

Approved Documents BS 476 Fire tests on building material and structures.

- A Structure - BS 476-3:2004 Classification and method of test for
- B Fire safety external fire exposure to roofs.
- C Site preparation and resistance to - BS 476-7:1997 Method of test to determine the
contaminants and moisture. classification of the surface spread of flame of
- L2A Conservation of fuel and power in new products.
buildings other than dwellings. - BS 476-22:1987 Methods for determination of the fire
- L2B Conservation of fuel and power in resistance of non-loadbearing elements of
existing buildings other than dwellings. construction.
BS 5250:2002 Code of practice for control of
The Scottish Building Standards: Technical Handbook.
condensation in buildings.
- Non-domestic.
BS 5950-5:1998 Structural use of steelwork in building.
Code of practice for design of cold formed thin gauge
sections
BS EN 1090-2:2008 Execution of steel structures and
aluminium structures. Technical requirements for the
execution of steel structures.
BS EN 1993-1-3:2006 Eurocode 3. Design of steel
structures. General rules. Supplementary rules for cold-
formed members and sheeting
BS 8206 Lighting for buildings.
- BS 8206-2:2008 Code of practice for daylighting.
BS EN 10143:2006 Continuously hot-dip coated steel
sheet and strip. Tolerances on dimensions and shape.
BS EN 10346:2009 Continuously hot-dip coated steel
flat products. Technical delivery conditions.
BS EN 12056 Gravity drainage systems inside buildings.
- BS EN 12056-3:2000 Roof drainage, layout and
calculation.
BS EN ISO 10211:2007 Thermal bridges in building
construction. Heat flows and surface temperatures.
Detailed calculations.
BS EN ISO 13788:2002 Hygrothermal performance of
building components and building elements. Internal
surface temperature to avoid critical surface humidity
and interstitial condensation. Calculation methods.
MRCMA Technical paper 14. Guidance for the design of
metal roofing and cladding to comply with Approved
Document L2: 2001
TM 37: Design for improved solar shading. 2006

purlins, rails & eaves beams

41
purlins, rails & eaves beams
technical support

steadmans website Product range Showcase

The Steadmans website is a
comprehensive, easy to navigate
database of information on
Steadmans and our complete range
of products and services.

All the information contained in our The Showcase section contains

technical brochures is included on the additional information and
website along with download pdfs of photographs of all the projects
individual brochure sections of some featured in this brochure.
products covering design guidance,
technical details and performance Literature
The information is divided into five
data. This section also includes
information sections:
additional products which do not
Product Range
have printed or download brochures.
Support
Showcase
Support
About Steadmans
Literature

In addition, there is a link on the

home page to our NBS Plus page This is a quick link to a page where
where you can access customisable you can request printed copies of our
specification clauses. brochures or download electronic
copies in PDF format.
Since our new website was
introduced in 2007 it has received The download page includes a link to
The Support section includes
over 5,500 visits per month. the free Acrobat Reader software
information on Fire Performance and
which enables you to read PDF files.
We strive to ensure that using the Warranties, a list of Frequently Asked
website is as rewarding as possible Questions, links to other relevant
and always welcome any feedback Organisations/Trade Associations/
you have regarding the content and Building Regulations and to our NBS
usability of our website. Plus Specifications. You can also
request information, and download
literature and installation instructions
for our sheets and other products.

purlins, rails & eaves beams

42
Steadmans are always happy
to provide advice on the
specification of our single
skin system and all of
our other products for
refurbishment and new
build projects.

Whatever the nature, size and

location of your project, we
can provide the expertise
and delivery schedules
essential to its success.

With more than

3 million of stock
available for immediate
delivery, Steadmans have built
up an enviable reputation for
providing quality products,
promptly and at
competitive prices -
a service which has
attracted many loyal
customers.

Our dedicated fleet of delivery

vehicles with self off-load
facilities also means that the
personal care taken to
produce our high quality
products is maintained
throughout the stages of
manufacture to the final
delivery to our customer.

purlins, rails & eaves beams

43
A. Steadman & Son
England & Wales Northern Ireland & Ireland Scotland
Warnell, Welton Unit 5, Scarva Road Industrial Estate 14 Grange Road
Carlisle Banbridge, Co. Down Houston Industrial Estate
Cumbria Northern Ireland Livingston
CA5 7HH BT32 3QD EH54 5DE

Tel: 01697 478 277 Tel: 02840 660 516 Tel: 01506 437 753
Fax: 01697 478 530 Fax: 02840 660 517 Fax: 01506 440 716

E-mail: [email protected]
Online: www.steadmans.co.uk

ENVIRONMENTAL CREDENTIALS

We recognise the need to manage the impact which our business and processes have on the environment.
We believe we have a responsibility to contribute to the well-being of the communities we live in.
We are committed to providing a clean, safe environment.

Developing sustainable construction methods presents a challenge to the whole construction industry.
Our main raw material, steel, is eminently recyclable: 85 - 90% of steel from demolition goes for
re-use and 40% of steel used in new construction has been recycled.

By using modern machinery and upgrading our facilities we are continually reducing
the impact of our products on the environment, and improving their contribution
to the long-term performance of buildings.

u k
ww s . c o.
w. s t e a d m an