User Manual

Version 3.1

VMT 5010

ads-tec GmbH
Raiffeisenstr.14
D-70771 Leinfelden-Echterdingen
Tel: +49 (0) 711 / 45894-0
Fax: +49 (0) 711 / 45894-990
[email protected]
http://www.ads-tec.com/
User Manual VMT 5010 V3.1

Copyright

ads-tec GmbH
Raiffeisenstr.14
D-70771 Leinfelden-Echterdingen
Germany

2 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

INDEX

ABOUT US .......................................................................................................................................... 5

1 REMARKS ................................................................................................................................. 6
1.1 RELEVANT DOCUMENTATION FOR THIS DEVICE ................................................................................ 6
1.2 USED SYMBOL EXPLANATION ..................................................................................................... 6
1.3 DATA, FIGURES AND MODIFICATIONS ........................................................................................... 6
1.4 TRADE MARKS ....................................................................................................................... 6
1.5 COPYRIGHTS ........................................................................................................................ 7
1.1 ENVIRONMENTAL CONDITIONS ................................................................................................... 7
1.2 STANDARDS ......................................................................................................................... 8
1.3 EQUIPMENT VERSIONS ............................................................................................................. 8
1.4 SCOPE OF DELIVERY ................................................................................................................ 9

2 OPERATING INSTRUCTIONS ....................................................................................................... 10

2.1 OPERATING LOCATION ............................................................................................................10
2.2 DAMAGE CAUSED BY IMPROPER USE ............................................................................................10
2.3 WARRANTY / REPAIR ..............................................................................................................11

3 INSTALLATION ........................................................................................................................ 12
3.1 INSTALLATION OPTIONS ..........................................................................................................12
3.2 EXTERNAL DEVICE DIMENSIONS .................................................................................................17

4 COMMISSIONING ..................................................................................................................... 18
4.1 AVAILABLE INTERFACES ..........................................................................................................18
4.2 CABLE INSTALLATION .............................................................................................................19
4.3 ORDER OF COMMISSIONING STEPS .............................................................................................19
4.4 CHECK OF READINESS FOR OPERATION ........................................................................................19

5 OPERATION ............................................................................................................................ 20
5.1 FRONT CONTROL KEYS ............................................................................................................20
5.2 SOFT KEYBOARD ...................................................................................................................21
5.3 TOUCHSCREEN .....................................................................................................................22
5.4 STATUS INDICATORS ..............................................................................................................22

6 INTERFACES............................................................................................................................ 23
6.1 INTERFACE SETUP .................................................................................................................23
6.2 SERIAL COM INTERFACE (RS232) ............................................................................................23
6.3 USB CONNECTIONS ...............................................................................................................24
6.4 EXTERNAL KEYBOARD .............................................................................................................25
6.5 MOUSE ..............................................................................................................................26

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 3

 User Manual VMT 5010 V3.1

6.6 24V DC POWER SUPPLY ......................................................................................................... 27

6.7 NETWORK CONNECTION (RJ45) ............................................................................................... 28
6.8 LINE OUT / SOUND ............................................................................................................... 28
6.9 OPTIONAL RADIO NETWORK CARD ............................................................................................. 28

7 DRIVES.................................................................................................................................. 29
7.1 HARD DRIVES / COMPACT FLASH DRIVES (IDE INTERFACE) ............................................................... 29
7.2 EXTERNAL DRIVES ................................................................................................................. 29

8 SOFTWARE & DRIVER INSTALLATION........................................................................................... 30

8.1 INSTALLING THE OPERATING SYSTEM .......................................................................................... 30
8.2 TOUCHSCREEN DRIVER INSTALLATION ......................................................................................... 31
8.3 SOFT KEYBOARD ................................................................................................................... 31

9 TECHNICAL DETAILS ................................................................................................................ 32

9.1 DISPLAY DATA ..................................................................................................................... 32
9.2 COMPUTER TECHNICAL DATA ................................................................................................... 32
9.3 GENERAL DATA .................................................................................................................... 32

10 SERVICE AND SUPPORT ............................................................................................................. 33

10.1 ADS-TEC SUPPORT................................................................................................................. 33

10.2 COMPANY ADDRESS ............................................................................................................... 33

4 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1
Pos: 1 /Datentechnik/Allgemeine Hinweise/Wir ber uns/Wir ber uns @ 0\mod_1158743732668_681.doc @ 692 @

ABOUT US

ads-tec GmbH
Raiffeisenstr. 14

70771 Leinfelden-Echterdingen
Tel: +49 (0) 711 / 45894-0
Fax: +49 (0) 711 / 45894-990
www.ads-tec.com
Germany

ads-tec GmbH provides large enterprises and globally active corporations with cutting edge
technology, up-to-date know-how and comprehensive services in the area of automation
technology, data processing technology and systems engineering.

ads-tec GmbH implements full automation solutions from planning to commissioning and is
specialized in handling and material handling technologies.

The data systems division develops and produces PC based solutions and offers a broad
range of industrial PCs, thin clients and embedded systems.

ads-tec is specialized in modifying and optimizing embedded operating systems and

develops software tools to complement its hardware platforms.

Pos: 2 /Datentechnik/Allgemeine Hinweise/Relevante Dokumentationen zum Gert/Relevante Dokumentationen fr OPC / CPC / OTC / VMT /STC/TT-Serie @ 1\mod_1204789290941_681.doc @ 3423 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 5

 User Manual VMT 5010 V3.1

1 REMARKS

1.1 RELEVANT DOCUMENTATION FOR THIS DEVICE

The following documents are essential for setting up and operating this device:
USER MANUAL ON SERVICE CD (DOCUMENTATION ON HAND):
Contains information for installation, commissioning and operating the device along with
technical data of the device hardware.
SERVICE CD:
Contains drivers and the user manual.
Note:
The "Drivers-xx.pdf" file contains an overview table showing which drivers from the
service CD are to be used for which device. You must open the "Which driver for which
device" menu item in order to open this file.
Pos: 3 /Datentechnik/Allgemeine Hinweise/Erluterung zu den verwendeten Symbolen/Erluterung zu den verwendeten Symbolen @ 0\mod_1158752779484_681.doc @ 690 @
a

1.2 USED SYMBOL EXPLANATION

W arning:
The "Warning" symbol refers to activities which might cause personal injury or damage to
the hardware or software!

Note:
The "Note" symbol familiarises you with conditions to be observed in order to ensure
flawless operation. Additionally, hints and advice are given for a more efficient use of the
device and for software optimisation.
Pos: 4 /Datentechnik/Allgemeine Hinweise/Daten, Abbildungen, nderungenDaten,Abbildungen,nderungen (2009-02-24 14:01:39) @ 0\mod_1158754051494_681.doc @ 694 @

1.3 DATA, FIGURES AND MODIFICATIONS

All texts, data and figures are non-binding. We reserve the right of modification in
accordance with technological progress. At that point in time when the products leave our
premises, they comply with all currently applicable legal requirements and regulations. The
operator/operating company is independently responsible for compliance with and
observance of any subsequently introduced technical innovations and new legal
requirements, as well as for all usual obligations of the operator/operating company.
Pos: 5 /Datentechnik/Allgemeine Hinweise/Warenzeichen/Warenzeichen @ 0\mod_1158755151363_681.doc @ 696 @

1.4 TRADE MARKS

We would like to remind you that all software and hardware designations as well as trade
names of companies used in this documentation are subject to the general, international
trade mark, brand or patent protection laws.

WINDOWS, WINDOWS CE and WINDOWS CE.net are trade marks registered by

Microsoft Corp.
Citrix and ICA are trade marks registered by Citrix Systems Inc.
Intel and Pentium are trade marks registered by Intel Corp.
IBM, PS/2 and VGA are trade marks registered by IBM Corp.

6 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

CompactFlash and CF are trademarks of SanDisk Corp.

All other nationally and internationally recognised trade marks and product names are
Pos: 6 /Datentechnik/Allgemeine Hinweise/Urheberrecht/Urheberrecht @ 0\mod_1158756954232_681.doc @ 698 @
hereby likewise recognised.

1.5 COPYRIGHTS
This manual, including all contained figures, is protected by copyright law. Any use for
third parties non-compliant with the copyright provisions is prohibited. Any reproduction,
translation as well as electronic and photographic archiving and modification shall only be
permitted after explicit written authorisation by ads-tec GmbH.
Any party in violation of this provision shall be obliged to damage compensation.
Pos: 7 /Datentechnik/Allgemeine Hinweise/Umweltbedingungen/Umweltbedingungen fr VMT 5008/10 @ 0\mod_1158759221430_681.doc @ 704 @

1.1 ENVIRONMENTAL CONDITIONS

The device may be operated under the following conditions. Failure to observe these
specifications will terminate any warranty for this device. Ads-tec cannot be held liable for
any damages arising due to improper use and handling.

Temperature for devices including a HDD:

In operation 0 45 C
For storage -20 45 C
(Because of the integrated max. temperature memory)

Temperature for devices including a compact flash memory:

In operation 0 45 C
For storage -20 45 C
(Because of the integrated max. temperature memory)

Temperature for devices including a heater (only CF-Devices)

In operation -20 45 C
For storage -20 45 C
(Because of the integrated max. temperature memory)

Humidity:
In operation 10 85% without condensate
For storage 10 85% without condensate

Vibrations:
In operation 1 G, 10 500 Hz
(EN 60068-2-6)

Shock resistance:
In operation 5 G, with a half-wave of 30 ms duration
(EN 60068-2-27)
Pos: 8 /Datentechnik/Allgemeine Hinweise/Normen/Normen @ 1\mod_1219145812377_681.doc @ 3946 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 7

 User Manual VMT 5010 V3.1

1.2 STANDARDS
This unit is compliant with the provisions and safety objectives of the following EU
Directives:

This unit is compliant with the CE mark testing specification limits as defined in the
European test standards EN 61000-6-4 und EN 61000-6-2

This unit is compliant to the DIN EN 60950 (VDE0805, IEC950) testing

specification limits on Safety of Information Technology Equipment

This unit is compliant to the DIN EN 60068-2-6 (sinusoidal vibration) testing

specification limits

This unit is compliant to the DIN EN 60068-2-27 (shock and bump) testing
specification limits

Note:
A corresponding declaration of conformity is available for competent authorities, care of
the Manufacturer. Said declaration can be viewed at all times upon request.
For full compliance to the legal requirements in force on electromagnetic compatibility, all
components and cables used for unit connection must also be compliant with said
regulations. It is therefore necessary to employ BUS and LAN cables featuring screened
plug connectors, to be strictly installed as per the instructions contained in the User
Manual.

Pos: 9 /Datentechnik/Allgemeine Hinweise/Ausstattungsvarianten/Ausstattungsvarianten fr IPC/5300/5500 /VMT-Serie @ 0\mod_1158760700338_681.doc @ 712 @

1.3 EQUIPMENT VERSIONS

The system is available in two equipment versions:

Platform for use with compact flash memories:

Platform without any rotating mass storage media (hard disks, etc.) including embedded
operating systems (Windows CE.net / XP embedded) for stationary use in connection with
standard Ethernet or radio network cards on portable commissioning and/or forklift
equipment.

Platform including hard disks:

Including hard disks for stationary use, e.g. in manufacturing using standard operating
systems.
Pos: 10 /Datentechnik/Allgemeine Hinweise/Lieferumfang/Lieferumfang fr VMT- Serie @ 0\mod_1158824011759_681.doc @ 718 @

8 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

1.4 SCOPE OF DELIVERY

Please check that all of the following components are contained in the packaging:

1 device
3 pin Feed-through connector from Phoenix Contact, COMBICON MC
1.5/3-STF-3.81 type (already connected with the device socket)
Service CD

Optional scope of delivery

Operating system
Installation kit
2.4 GHz WLAN antennas, enclosed for b/g

Pos: 11 /Datentechnik/Betriebshinweise/Betriebsort/Betriebsort fr VMT-Serie @ 0\mod_1158826710817_681.doc @ 726 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 9

 User Manual VMT 5010 V3.1

2 OPERATING INSTRUCTIONS
This device contains electrical voltages and extremely sensitive components. The
manufacturer, or a service partner authorised by the manufacturer, should be consulted if
you plan to make any modifications. For this type of work, the device must be switched off
at the mains and the power lead must be disconnected. Suitable measures for avoiding
electrostatic discharge towards parts of the components when touching the equipment
must be taken. If the device is opened by an unauthorised person, hazards for the user
might arise and any warranty claim will cease.

General instructions:
All users must read this manual and have access to it at all times.
Installation, commissioning and operation may only be carried out by trained and
qualified staff.
The security instructions and the manual itself must be observed by all persons
who work with this device.
At the location of use, the valid guidelines and regulations for accident prevention
must be observed.
The manual contains the most important instructions on how to use this device in
a safe way.
Appropriate storage, proper transport, installation and commissioning, as well as
careful operation are prerequisites for ensuring safe and proper operation of the
device.

W arning:
Any leads (e.g. power leads, interface cables) may only be connected if the device is
switched off in order to avoid damaging the device.

2.1 OPERATING LOCATION

The VMT control system is designed for use with support arm systems or on mobile base
equipment (commissioning trolleys, fork lift equipment, and similar). You have to take care
that the environmental conditions indicated in the technical specification are met. Using
the device in non-specified environments, for example on board ship or in areas that might
contain explosive gases, or in extreme heights, is prohibited.

W arning:
The device may only be switched on after acclimatising to the ambient temperature in
order to avoid condensate accumulation. The same applies if the device has previously
been exposed to extreme temperature variations.
To avoid overheating in operation: The device must never be exposed to direct radiation
by sunlight or any other light or heat source.

Pos: 12 /Datentechnik/Betriebshinweise/Schden durch unsachgemen Gebrauch/Schden durch unsachgemen Gebrauch @ 0\mod_1158827867958_681.doc @ 728 @

2.2 DAMAGE CAUSED BY IMPROPER USE

This device must immediately be shut down and protected from any accidental
commissioning if the operating system shows any obvious damage caused by, for example,
improper operating or storage conditions, or by improper use or handling.
Pos: 13 /Datentechnik/Betriebshinweise/Gewhrleistung / Reparatur/Gewhrleistung / Reparatur @ 0\mod_1158828054427_681.doc @ 730 @

10 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

2.3 WARRANTY / REPAIR

During the warranty period any repair must only be carried out by the manufacturer or by
Pos: 14 /Datentechnik/Montage/Montagemglichkeiten/Montagemglichkeit fr VMT 5010 @ 1\mod_1220963883505_681.doc @ 4033 @
a person authorised by the manufacturer.

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 11

User Manual VMT 5010 V3.1

3 INSTALLATION

3.1 INSTALLATION OPTIONS

Gallow bracket for Rittal systems
The stainless steel installation bracket for gallow type installations (CP-S/CP-L) has four
drill holes. By using this bracket, the device can be fixed on a gallows. You can set the
angle of the device towards the front or rear in several steps by loosening the self-locking
screws on both sides, in order to set up the angle of viewing.

12 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

Bracket for VESA standard

The stainless steel installation bracket for the VESA standard (75mm) has four drill holes.
Using this bracket, the device can be fitted to a wall or to a VESA coupler. You can set the
angle of the device towards the front or rear in several steps by loosening the self-locking
screws on both sides, in order to set up the angle of viewing.

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 13

User Manual VMT 5010 V3.1

Desktop bracket
The stainless steel bracket for desktop installation has 12 drill holes. By using this bracket,
the device can be fixed to a control stand or desktop. You can set the angle of the device
towards the front or rear in several steps by loosening the self-locking screws on both
sides, in order to set up the angle of viewing.

14 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

Bracket for 90 installation

The stainless steel bracket for angled installation in a 90 angle allows a flexible use. It has
four drill holes for fixing the device. You can set the angle of the device towards the front
or rear in several steps by loosening the self-locking screws on both sides, in order to set
up the angle of viewing

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 15

 User Manual VMT 5010 V3.1

Customer-specific brackets
For manufacturing of customer specific brackets, you'd have to consider that the bolts on
the device side are fixed, and cannot be removed.

Note:
The figure on this page shows a VMT 5012 device. The VMT fixing points for a customer-
specific bracket are the same with all VMT devices.

Pos: 15 /Datentechnik/Montage/Montageskizzen/Auenabmessungen des Gerts/Montageskizze / Auenabmessungen fr VMT5010 @ 1\mod_1204730320043_681.doc @ 3415 @

16 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

3.2 EXTERNAL DEVICE DIMENSIONS

Pos: 16 /Datentechnik/Inbetriebnahme/Systemmerkmale/Inbetriebnahme fr VMT 50xx-Serie @ 0\mod_1158845383048_681.doc @ 792 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 17

 User Manual VMT 5010 V3.1

4 COMMISSIONING
The power supply connection and interfaces of this device are installed inside the case.
You have to remove the case cover in order to connect the power supply cables and the
interface cables.
All supply leads and all required data leads have to be connected before commissioning.

W arning:
The device must be switched off before connecting or disconnecting any cables in order
to prevent damage to the electronics!
The device may only be switched on after acclimatising to the ambient temperature in
order to avoid condensate accumulation. Make sure to meet the admissible voltage
requirements for this device.
After switching off and before switching on you must wait for at least 5 seconds.

Note:
The screen of a data cable must always be connected with the connector housing (EMC).
Under the embedded operating system, interfaces must explicitly be enabled and required
drivers must be installed in order to be able to use them.

4.1 AVAILABLE INTERFACES

Pos: 17 /Datentechnik/Inbetriebnahme/Kabelmontage/Kabelmontage fr VMT-Serie / MSA 5012 / 5015 @ 0\mod_1158847931866_681.doc @ 798 @

Hinw eis:
The device can be started with the ignition function.

18 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

4.2 CABLE INSTALLATION

The power supply connectors and interfaces of this device are installed inside the case.
Cables can be routed through rubber grommets and exit the case on the bottom. The
grommets are inserted between the case and the cover, and can easily be removed after
removing the cover. Since this device includes the required input peripherals (soft
keyboard / touch screen), only one grommet for the power supply cable (cable diameter of
6...7mm) as well as three blank plugs are integrated by default. Should it be required to
feed through more cables from the device to the outside, these blank plugs must be
replaced by suitable grommets (optionally available accessories).
Pos: 18 /Datentechnik/Inbetriebnahme/Reihenfolge der Inbetriebnahme/Reihenfolge der Inbetriebnahme fr VMT 50xx-Serie @ 0\mod_1158848845491_681.doc @ 803 @

4.3 ORDER OF COMMISSIONING STEPS

Remove the case cover screws and carefully remove the cover.
Fix the wires of the power supply cable in the screw terminals by using Phoenix
Combicon in wire end sleeves.
Plug the data cable connector on the desired interface connector and screw it on,
if possible.
Select a cable grommet with a suitable diameter for each cable to be fed through,
and enclose the cable with it. Additionally there are cord grips for different cable
sizes available.
Remove the blank plug and replace it with the grommet surrounding the cable.
Attach the case cover properly and install the screws.

Note:
The service slot is fixed with captive screws.

W arning:
Full protection according to the indicated protection class is only ensured if the case cover
is properly installed!
Pos: 19 /Datentechnik/Inbetriebnahme/Betriebsbereitschaft prfen/Betriebsbereitschaft prfen fr OPC/CPC/PLC/OTC/ITC/VMT-Serie(+Monitore) / IPC 5100/5500/2400/1100 @ 0\mod_1158905578361_681.doc @ 806 @

4.4 CHECK OF READINESS FOR OPERATION

Check the device for any hidden damage caused by improper transport, improper
operating or storage conditions or by improper use (e.g. smoke development from the
device, etc.). Immediately shut down the device and prevent any further accidental
commissioning if any damage is detected.

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 19

 User Manual VMT 5010 V3.1

5 OPERATION

5.1 FRONT CONTROL KEYS

Depending on the equipment version of the device, an operating system (Windows CE.net,
Windows XP embedded or Windows XP Prof.) and a soft keyboard might be already
installed ex factory. The following functions are already assigned to the keys on the front
panel by a specific driver in the soft keyboard:

On / Off pushbutton for the device (ATX functionality)

Level 1:
Activate and deactivate the soft keyboard for letter/character input
using the touchscreen.
Level 2:
Increase the volume with devices using a speaker/audio output.

Level 1:
Change tasks (Alt+ESC) in Windows.
Level 2:
Decrease the volume with devices using a speaker/audio output.

Level 1:
Not connected
Level 2:
Increase display brightness

Level 1:
Right mouse-key function
Level 2:
Decrease display brightness

Shift key (SHIFT) for activating the second keyboard level. This key
must be pressed simultaneously with the desired function key.

Note:
If the software keyboard is not installed, only the functions for display settings and
volume control are active. The controller display is not output on the display, in this
case. The functions assigned to the keys, might already be modified according to
customer specifications. Above described functions are pre-set ex works.

Pos: 21 /Datentechnik/Bedienung/Softkeyboard/Softkeyboard fr OPC / CPC / OTC / VMT / STC-Serie @ 1\mod_1204714082851_681.doc @ 3403 @

20 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

5.2 SOFT KEYBOARD

If the operating system is installed ex works, the soft keyboard is included in this
installation. If the device is delivered without any operating system, the soft keyboard has
to be installed by the customer. By using the soft keyboard, data can be entered via the
touchscreen like with an external keyboard.

HOW TO OPERATE THE SOFT KEYBOARD FROM VERSION 3.11:

Activate and deactivate the soft keyboard for letter/character input using
the touchscreen

Switches display of numeric keypad on/off (only if numeric keypad is

displayed)

Switching between representation modes (alphanumeric keypad

numeric keypad bar of function keys)

Soft keyboard representation, zoom in

Soft keyboard representation, zoom out

Note:
If a function is to be activated, which requires pressing two keys at the same time (e.g.
Alt + F4); these keys have to be pushed one after another at the soft keyboard, and the
special keys Shift, Alt and Ctrl must always be pushed first.
Due to differences in programming of a large variety of software, we cannot ensure that
the soft keyboard works properly with all software.
When deactivating the soft keyboard, the previously active state (alphanumeric / numeric
keys or function keys) will be stored and will be displayed when re-activating the
keyboard.

Pos: 22 /Datentechnik/Bedienung/Touch Screen/Touch Screen fr OPC / VMT-Serie / OTC 5006 / CPC 5006 / PLC 500 / STC 5015 Multitest @ 0\mod_1158911350731_681.doc @ 825 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 21

 User Manual VMT 5010 V3.1

5.3 TOUCHSCREEN
The control system is equipped with an touchscreen. The touchscreen is internally
connected with a serial interface. The driver software required for its use is already
integrated in the corresponding operating system, or can be installed from the attached
service CD.
Pos: 23 /Datentechnik/Bedienung/Status-Anzeigen/SYS-LED/SYS-LED fr OPC / CPC / PLC / OTC / ITC / VMT (+Monitore) - Serie / IPC 5100 / 5300 / 5500 / 1100 @ 1\mod_1204714132162_681.doc @ 3406 @

5.4 STATUS INDICATORS

SYS LED (BICOLOURED)
Depending on the colour and type of flashing, different device states are displayed by the
SYS LED.

The following signals are displayed:

LED lights green The device is ready for operation (Power ON).
LED is off The device is switched off. (Power OFF)
Pos: 24 /Datentechnik/Schnittstellen/Schnittstelleneinstellung/Schnittstelleneinstellung fr VMT-Serie / PLC 500 @ 0\mod_1158916296612_681.doc @ 855 @

22 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

6 INTERFACES

6.1 INTERFACE SETUP

INTERFACE IRQ ADDRESS

COM1 4 3F8h
COM2 (Touch) 3 2F8h

Pos: 25 /Datentechnik/Schnittstellen/Serielle Schnittstelle COM RS232/Serielle Schnittstelle COM (RS232) fr OPC / IPC / CPC / PLC / OTC / ITC / VMT / MSA-Serie @ 0\mod_1158925008814_681.doc @ 871 @

6.2 SERIAL COM INTERFACE (RS232)

The serial interface is used for digital and for analogue data transmission as well. The RS
232 interface can be connected by using a commercially available 9-pin SUB-D cable.

PIN NUMBER SIGNAL NAME

1 DCD

2 RxD

3 TxD

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 RI

Note:
This interface is not electrically isolated.

Pos: 26 /Datentechnik/Schnittstellen/USB-Anschluss/USB-Anschluss fr OPC / IPC / CPC / PLC / OTC / ITC / VMT / MSD-Serie @ 0\mod_1158923823971_681.doc @ 865 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 23

 User Manual VMT 5010 V3.1

6.3 USB CONNECTIONS

The USB interfaces are used for connecting peripherals with USB connection. The interface
complies with the USB 2.0 standard.

PIN NUMBER SIGNAL NAME

1 VDC

2 D-

3 D+

4 GND

Note:
The USB interfaces may be locked using the Lock USB software tool.
You'll find this software and the documentation on the service CD.
USB CONNECTION ON THE FRONT PANEL
One USB interface can be accessed from the front. This interface is located under a plastic
cover beneath the display. The cover has a tab on the right-hand side, which is used for
opening. The plastic cover must properly be replaced and carefully closed after using the
USB interface, since otherwise the protection class of IP65 is no longer ensured.
Pos: 27 /Datentechnik/Schnittstellen/Externe Tastatur/Externe Tastatur fr OPC / CPC / PLC / OTC / ITC / VMT-Serie / IPC 51/ 53/11/5500 @ 0\mod_1169193199871_681.doc @ 2206 @

24 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

6.4 EXTERNAL KEYBOARD

One mouse and one keyboard can be connected with both existing PS2 connectors. These
connections are colour coded for proper connection with this device.

PIN NUMBER SIGNAL NAME

1 Data

2 NC

3 GND

4 +5V

5 Clock

6 NC

The control system has a purple coloured 6-pin mini-DIN socket (PS2) identified as
KEYB". Any commercially available AT-compatible quality keyboard equipped with the
required connector can be connected with this socket. Check the keyboard for proper
function before using it.

Note:
Since the timing of the integrated controller is optimised for Cherry keyboards, keyboards
of this manufacturer should preferably be used.
If the screen shows that the soft keyboard is active, controlling the device by using the
external keyboard is possible with restrictions only.
The keyboard must be connected before switching the device on, since the keyboard
interface is initialised while booting! If the keyboard is connected during operation of this
device, and the keyboard was not connected during the booting process, it is not
operable.
The device features an keyboard simulator, which can be used to connect a scanner.
Pos: 28 /Datentechnik/Schnittstellen/Maus/Maus fr OPC / IPC 51/53/55 / 1100/ 2400 / CPC / PLC /OTC / ITC / VMT-Serie @ 0\mod_1158910619667_681.doc @ 821 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 25

 User Manual VMT 5010 V3.1

6.5 MOUSE
The green coloured interface "MOUSE" is used to connect a mouse. Check the mouse for
compatibility before using it.

PIN NUMBER SIGNAL NAME

1 Data

2 NC

3 GND

4 +5V

5 Clock

6 NC

Note:
The mouse must be connected before switching the device on, since the mouse interface
is initialised while booting! If the mouse is connected during operation of this device, and
the mouse was not connected during the booting process, it is not operable.
Pos: 29 /Datentechnik/Schnittstellen/Spannungsversorgung/Spannungsversorgung fr VMT50xx-Serie @ 0\mod_1158918964340_681.doc @ 863 @

26 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

6.6 24V DC POWER SUPPLY

The power supply voltage is supplied via a feed-through clamp including screw
connection (figure shows socket in the device).

PIN NUMBER SIGNAL NAME

1 24V DC
2 Ignition contact
3 0V DC

Voltage tolerance
In the equipment version with a 24V DC 20% power supply, a DC-DC converter is
integrated.

Input voltage: 24V DC 20%.

Current consumption
The current consumption of the device depends on the equipment version of this device.
(heater, WLAN, etc.)

Switch-on current: 7 Amperes (for 2ms)

Standby input current: 0.1 Ampere
maximum input current using heater: 2.5 Amperes
Regular operation: 1.5 Amperes without heater

Note:
The typical power consumption of this device is indicated in the "Technical details"
chapter.

Pos: 30 /Datentechnik/Schnittstellen/Netzwerkanschluss RJ45/Netzwerkanschluss RJ45 fr OPC / IPC / CPC / PLC / OTC / ITC / VMT-Serie/LSI 5015 SEW @ 0\mod_1158924094127_681.doc @ 867 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 27

 User Manual VMT 5010 V3.1

6.7 NETWORK CONNECTION (RJ45)

If the drivers required for functioning are installed on the device, the control system may
be integrated in an Ethernet network supporting the 10/100 Mbit standard by using the
Ethernet 10/100BaseT network connector. Specifications of this network topology must be
observed in this case. You can install the drivers required for functioning from the enclosed
service CD, should they not be installed on the device.

PIN NUMBER SIGNAL NAME

1 TX +

2 TX -

3 RX +

4 NC

5 NC

6 RX -

7 NC

8 NC

Pos: 31 /Datentechnik/Schnittstellen/Line Out/Line Out / Sound fr VMT-Serie @ 0\mod_1159172305673_681.doc @ 917 @

6.8 LINE OUT / SOUND

The Line Out connection of this device is a 3.5 mm socket which provides a stereo signal.
In order to use this connection, the matching plug must be wired up as follows.

PIN NUMBER SIGNAL NAME

Ground GND

R Signal, right-hand side

Pos: 32 /Datentechnik/Schnittstellen/Funknetzwerkkarte/Funknetzwerkkarte fr VMT-Serie @ 0\mod_1159172416532_681.doc @ 919 @

L Signal, left-hand side

6.9 OPTIONAL RADIO NETWORK CARD

If a slot with a radio network card and an externally attached antenna is installed in the
device, and if this card is supported by the corresponding drivers in the operating system,
this device may be integrated in an Ethernet network supporting 11 Mbit or 54 Mbit
(802.11a/b/g compatible) connections. Specifications of this network topology must be
observed in this case.
Pos: 33 /Datentechnik/Laufwerke/Externe Laufwerke/Externe Laufwerke fr OPC 5112 / 5115 / 5117 / IPC 1100 / CPC / PLC / OTC / ITC / VMT-Serie @ 0\mod_1158926656205_681.doc @ 880 @

Pos: 34 /Datentechnik/Laufwerke/Festplatte / Compact Flash/Festplatte Compact Flash fr VMT-Serie @ 1\mod_1204714324328_681.doc @ 3409 @

28 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

7 DRIVES

7.1 HARD DRIVES / COMPACT FLASH DRIVES (IDE INTERFACE)

The storage medium is selected according to the customer requirements. The following
options are available for storage:

Compact Flash memory:

Compact flash memories with a storage capacity of at least 64 MB are
used. The capacity depends on the desired operating system and the
additional programmes to be installed.
Hard disk: A 1.8" hard disk with at least 20 GB (UDMA) is used. On delivery, the
hard disk is formatted in NTFS format (default for Windows XP).

Note:
Recommendation for selection of storage media with a basic installation:
Compact Flash: Windows CE.5.0 / Windows XP embedded
Hard disk: Windows XP Professional

7.2 EXTERNAL DRIVES

By default, no drive for removable media (CD/floppy disk) is integrated in the device.
Additionally the system provides an USB interface, with which an external drive could be
connected. In this case, you'd have to ensure that the equipment used is suitable for use
in an industrial environment.

W arning:
Connecting or disconnecting of external drives during operation is inadmissible, since it
cannot be excluded that the drive is in use at this point in time. Data loss might occur if
not observed!

Pos: 35 /Datentechnik/Software / Treiber Installation/Installation des Betriebssystems/Installation des Bertiebssystems fr/IPC 11/CPC/PLC/OTC/ VMT-Serie/OPC -Serie @ 0\mod_1159173231142_681.doc @ 926 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 29

 User Manual VMT 5010 V3.1

8 SOFTWARE & DRIVER INSTALLATION

The device will be delivered with a pre-installed Windows operating system on request by
the customer. The drivers required for this are already installed, and the operating system
will be enabled by entering the licence information. Should an initial installation be
required, please adhere to the following steps. With a newer operating system like
Windows XP, the network card and graphics card will properly be recognised during initial
installation, so that only the touchscreen driver and the soft keyboard must be installed
separately.

Note:
If the hard drive was formatted, the operating system can be reinstalled by using one of
the existing interfaces.
An external keyboard is required for installation.

8.1 INSTALLING THE OPERATING SYSTEM

If the device is not equipped with an integrated drive, installing the operating system can
only be carried out by using the USB interface.

Procedure for installation:

USB:
The boot drive in the system Bios must be switched to USB in order to boot the
device from the USB interface.
Restart the device and insert the Windows CD.
Windows installation and basic data setup
With devices using a touchscreen, the full functionality range or touchscreen
drivers and the soft keyboard should be installed.
If Windows CE.net or Windows XPe is used, the entire operating system may be
completely installed from the USB stick using the respective image. The required image
can be purchased from the ads-tec company or via the ASSIX online portal.
Pos: 36 /Datentechnik/Software / Treiber Installation/Touch Screen/Touch Screen Installation fr OPC 5112/5212/5315/5515/5317/5319 / CPC5006/OTC5006/ VMT-Serie @ 0\mod_1159175108636_681.doc @ 931 @

30 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

8.2 TOUCHSCREEN DRIVER INSTALLATION

Note:
When installing the drivers, you have to consider that the touchscreen is connected with
the serial interface!
Touchscreen and PS2 mouse can be used simultaneously

Installation must be carried out as described below:

Switch on PC and boot
Start the installer file in the touchscreen folder by accessing the service CD with
the Windows Explorer.
Follow the instructions on screen and agree to the licensing conditions.
Once the installer is finished, shut down the computer and restart it.
After restarting the touchscreen must be calibrated. If the driver does not start
automatically, open the setup menu by using the "Start => Settings =>
Control panel => Elo Touchscreen" directory path.
Start the touchscreen calibration by using the "Calibration data" item, and push
the crosses, which appear one after another on the screen. If the cursor position
coincides with the touch point of your finger on the touchscreen, exit the control
Pos: 37 /Datentechnik/Software / Treiber Installation/Softkeyboard/Softkeytastatur fr alle Gert ohne internes Laufwerk(CD/DVD) @ 0\mod_1159175310134_681.doc @ 933 @
box by using the "OK" button.

8.3 SOFT KEYBOARD

The soft keyboard must be installed from the enclosed CD-ROM in order to enable using
the 5 keys (exception: VMT-series, there are 6 keys) underneath the screen. Installation
must be carried out as described below:

Connect the external drive with the device.

Switch the PC on, and insert the driver CD into the drive after booting.
Start the installer from the service CD.
Follow the on-screen instructions, install the driver, select the language and
confirm that the computer is going to be restarted.

Note:
Further settings can be performed with respect to the basic settings of the soft keyboard.
You'll find information about this in the Readme file in the installation folder for the soft
keyboard!
Pos: 38 /Datentechnik/Technische Daten/VMT-Serie/VMT 50xx-Serie/Technische Daten fr VMT 5010 @ 0\mod_1160396915894_681.doc @ 1236 @

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 31

 User Manual VMT 5010 V3.1

9 TECHNICAL DETAILS

9.1 DISPLAY DATA

Display 10.4" TFT, 800 x 600 Pixel
Displayable colors max. 16.7 Mio. colors
TouchScreen Resistive industrial touch screen

9.2 COMPUTER TECHNICAL DATA

The device can be furnished with the following adsX modules (depending on customer
requirements).

VERSION 1 Celeron M 1.0 GHz ULV

256MB - 2GB DDR RAM
Intel 855 GME

VERSION 2 Celeron M 800 MHz ULV

256MB - 2GB DDR RAM
Intel 855 GME

Graphics memory max. 64 MB shared

Mass storage 1x CompactFlash card
Alternative: 1,8" hard disk with min. 20 GB (UDMA)

Interfaces COM 1 (RS232), 1x PS2 mouse, 1x PS/2 keyboard,

2x USB 2.0, 1x Mini PCI, 1x PCMCIA,
line out, 2x internal speakers

Network 1x Ethernet (10/100 Mbit) RJ 45 (Intel 52551QM)

Power supply unit 24V DC +/- 20%

9.3 GENERAL DATA

External dimensions 295 mm x 232 mm x 57 mm (W x H x D)
Weight approx. 2.5 kg
Protection class IP 65
Power consumption 24 Watts (type)
Max. switch-on current 7 Amperes (2ms)
Pos: 39 /Datentechnik/Service und Support/Service & Support @ 0\mod_1159176214322_681.doc @ 938 @

32 ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen

 User Manual VMT 5010 V3.1

10 SERVICE AND SUPPORT

The ads-tec company and their partner companies offer a comprehensive service and
support to your customers providing a quick and professional support in case of any
question with respect to ads-tec products and components.

Since the devices from ads-tech company are also used by partner companies, these
devices might be configured according to customer requirements. Should any question or
issue with respect to specific configurations and software installations arise, it can only be
resolved by the system manufacturer.
For devices not directly purchased from ads-tec, we cannot be responsible for the support.
In this case, the support is provided by our partner company.

10.1 ADS-TEC SUPPORT

The ads-tec support team is available for direct clients from Monday to Friday from
08:30 AM to 05:00 PM using the following phone number:

Phone: +49 (0) 711 / 45894-500

Fax: +49 (0) 711 / 45894-990
Email: [email protected]

10.2 COMPANY ADDRESS

ads-tec
Automation Daten- und Systemtechnik GmbH
Raiffeisenstrae 14
D-70771 Leinfelden-Echterdingen
Germany

Phone: +49 (0) 711 / 45894-0

Fax: +49 (0) 711 / 45894-990
Email: [email protected]

===== Ende der Stckliste =====

Home: www.ads-tec.de

ads-tec GmbH Raiffeisenstr.14 70771 Leinfelden-Echterdingen 33