Sophos UTM Software Appliance

Quick Start Guide

Product version: 9.300

Document date: Monday, December 01, 2014
 Sophos UTM Minimum Hard-
ware Requirements
Intel compatible CPU 1.5 GHz+
1 GB RAM (2 GB recommended)
Dual Core (Quad Core recommended)
20 GB hard disk drive (40 GB recom-
mended)
Bootable CD-Rom drive or Sophos Smart
Installer
2+ NICs (WAN, LAN)

Client Hardware/Software
Requirements
Any system capable of running a current
version of Firefox, Internet Explorer, or
Chrome. Best if managed with keyboard
and if a mouse is available.
WebAdmin is running on HTTPS at port
4444.

1. Install the software

Install the Sophos UTM V9 software on a
separate host. The installation will com-
pletely erase all data on the hard disk
including all programs and the operating
system. After the security system has
rebooted (a process which, depending on
hardware, can take up to five minutes),
ping the IP address of the UTM to make
sure it is reachable. The default address
is 192.168.2.100, but you will be promp-
ted to set this during the installation.
Make note of the new IP if you change it.

Sophos UTM Software Appliance - Quick Start Guide

 2. Use your browser to make
the initial connection to the
Workstation Connection Properties: WebAdmin GUI
IP address: Any address in the range 192.168.2.1 through
You will need to configure a workstation
192.168.2.99
with the necessary LAN settings to
Netmask: Enter 255.255.255.0 access WebAdmin. You can change
Standard gateway: Enter the IP address of the UTM internal network these settings later to match your existing
card: 192.168.2.100 network. The location of the menu for
DNS server: Enable this option and enter the IP address of the these settings depends on the operating
internal network card (eth0): 192.168.2.100 system of your workstation.
Example: With Windows 7, the menu can
be found under Start > Control Panel >
Network and Sharing Center.
Once your browser is correctly con-
figured, launch the browser and enter the
IP address of the Sophos UTM
WebAdmin as follows:
https://IP address:4444 (e.g.
https://192.168.2.100:4444).

3. Enter the administrator

contact and set admin
password
In the basic system setup window, enter
the administrator contact and the pass-
words for the Sophos UTM appliance. Be
sure to remember the password you
choose. This will be needed in step 4.

4. Log in to WebAdmin
Username: admin
Password: Password of the WebAdmin
user as set above in step 3.

Sophos UTM Software Appliance - Quick Start Guide

 5. Use the setup wizard
Select Continue and click Next to pro-
ceed with your installation.

6. Upload a license
If you already have a valid license for this
UTM, click the yellow browser folder to
locate your UTM license, then click the
Start upload button to apply it. If no
license is specified, a full 30-day trial will
begin. Click Next.

7. Specify your LAN settings

This will default to the IP address you set
during the initial installation. If you wish to
change this, enter the new IP address
you want the UTM appliance to use on
the internal network, along with the net-
mask. Leave DHCP server enabled, and
click Next.
Settings will not be applied until the wiz-
ard is complete.

Sophos UTM Software Appliance - Quick Start Guide

 8. Specify your Internet
connection settings
Select the interface that will be connected
to an Internet uplink. The required con-
figuration settings will depend on the type
of connection you are provided. If you are
unsure what settings to choose, consult
the settings provided by your ISP, or try
Standard Ethernet interface with dynamic
IP address, if no settings were provided.
Click Next.

9. Configure the firewall

By default, all traffic will be blocked.
Select which services you want to allow.
You can further configure rules in the Fire-
wall section after the wizard completes.
Click Next.

10. Configure Advanced

Threat Protection Settings
Enable the Intrusion Prevention Engine to
scan inbound traffic for threats. Enable
the Command & Control/Botnet Detec-
tion Engine to detect and prevent per-
sistent threats that may exist within the
network from phoning home. Click Next.

Sophos UTM Software Appliance - Quick Start Guide

 11. Configure web content
filtering
If you want to protect and control web surf-
ing, select options for virus and spyware
scanning and/or the categories you wish
to deny to your users. Click Next.

12. Configure email filtering

If you want to filter incoming messages to
your mail server (SMTP) or clients
(POP3) select the desired mode. The
example illustrates mail settings for
mycompany.com which will be scanned
for spam and viruses and then sent to the
mail server IP internally at 192.168.0.5.

Sophos UTM Software Appliance - Quick Start Guide

 13. Review and finish
The summary screen shows the con-
figuration about to be created. Click Fin-
ish and your settings will be applied.
Features configured by the wizard can be
edited as desired using any of the
WebAdmin menus to alter the settings at
any time to fit your needs. See the
Sophos UTM Administration Guide* for
more setup options. Enjoy your Sophos
UTM.
* Available via WebAdmin > Support >
Documentation > Manual or the know-
ledgebase:
sophos.com/kb.

United Kingdom Sales: North American Sales: Australia & New Zealand Sales:
Tel: +44 (0)8447 671131 Toll Free: 1-866-866-2802 Tel: +61 2 9409 9100
Email: [email protected] Email: [email protected] Email: [email protected]

Boston, USA | Oxford, UK

Copyright 2014. Sophos Ltd. All rights reserved.
All trademarks are the property of their respective owners.
Sophos Quick Start Guide 12.11v1.dNA