Study On Mechanical Properties of Concrete On Partial Replacement of Fine Aggregate With Copper Slag and Granite Powder
Study On Mechanical Properties of Concrete On Partial Replacement of Fine Aggregate With Copper Slag and Granite Powder
Study On Mechanical Properties of Concrete On Partial Replacement of Fine Aggregate With Copper Slag and Granite Powder
M.K.M.V Ratnam
Assistant Professor
Department of Civil Engineering
DNR College of Engineering & Technology, Bhimavaram, Andhrapradesh, India
Abstract
Concrete is the most popular building material in the world. It is the most consumable material after water. Concrete is a mixer
of binding material, fine aggregate, coarse aggregate and water. Generally Ordinary Portland Cement (OPC) is used as a binding
material, Hard Broken Granite (HBG) stone is used as a coarse aggregate and River sand has been the most popular choice for
the fine aggregate component of concrete in the past, but overuse of these materials has led to environmental concerns, the
depleting of securable Natural resource deposits and a concomitant price increase in the material. As environmental and cost
concerns Industrial waste or industrial by products can be used as a partial or full replacement of natural resources. The present,
study concerns with the partial replacement of fine aggregate in conventional concrete. The reduction in the sources of natural
sand and the requirement for reduction in the cost of concrete production has resulted in the increased need to identify substitute
material to sand as fine aggregates in the production of concrete. Various type of materials can be used for replacement in fine
aggregate. In which, some of the materials are Copper slag, Granite powder, Granulated blast furnace slag, Washed bottom ash,
Quarry dust, Foundry sand, Spent fire bricks, Sheet glass powder, Construction and demolition waste, etc. In present study
copper slag and granite powder can be used as a partial replacement of sand. Granite stone powder, a by-product from the cutting
process of granite stone used for flooring is one of such materials. Copper slag is a by-product obtained during the matte
smelting and refining of copper. The reduction in waste generation by manufacturing value-added products from the granite
stone waste will boost up the economy of the granite stone industry. The utilization of granite powder and copper slag in high
performance concrete could turn this waste material into a valuable resource with the added benefit of preserving environment.
At the same time Copper slag possesses mechanical and chemical characteristics that qualify the material to be used in concrete
as a partial replacement or as a substitute for fine aggregates since it is available in large quantity from the world copper
industry. In recent days there were also been many attempts to use Fly Ash, an industrial by product as partial replacement for
cement to have higher workability, long term strength and to make the concrete more economically available. Here it was
attempted the use of Pozzolana Portland Cement (PPC) instead of Ordinary Portland Cement (OPC). This present work is also an
attempt to use Granite powder and Copper slag as partial replacement for Sand in M25 grade concrete. Attempts have been made
to study the properties of concrete and some properties of Granite powder and Copper slag, their suitability of those properties to
enable them to be used as partial replacement materials for sand in concrete.
Keywords: Portland cement, concrete, rice hush Ash (RHA), Specimen Preparation, Testing
_______________________________________________________________________________________________________
I. INTRODUCTION
Concrete is a non-homogeneous material. It consists of cement, sand and mixed with water. The cement and water form a paste
or gel which coats the sand and aggregate. When the cement has chemically reacted with the water (hydrated), it hardens and
binds the whole mix together. The initial hardening reaction usually occurs within a few hours. It takes some weeks for concrete
to reach full hardness and strength.
Aggregate is the important constituent in concrete. They give body to the concrete, reduce shrinkage and effect economy.
Aggregate is a broad category of coarse particulate material used in construction, including sand, gravel, crushed stone, slag,
recycled concrete and geosynthetic aggregates. Aggregates are the most mined materials in the world. Aggregate serves as
reinforcement to add strength to the overall composite material. Aggregates are divided into two categories from the
consideration of size (i) coarse aggregate and (ii) fine aggregate. The size of aggregate is bigger than 4.75mm is considered as
coarse aggregate and whose size is 4.75mm and less is considered as fine aggregate. Hard Broken Granite stone is most
commonly used coarse aggregate material and river sand can be used as fine aggregate material in conventional concrete.
Baboo Rai et al (2011) [4] investigated the effect of using marble powder and granules as constituents of fines in concrete by
partially reducing quantities of cement as well as other conventional fines. The values of workability, compressive strength and
flexural strengths were found. Partial replacement of cement and usual fine aggregates with varying percentage of marble
powder (0%,5%,10%,15%,20%) and marble granules revealed that increased waste marble powder (WMP) or waste marble
granule (WMG) resulted in increase in workability and compressive strength of mortar concrete.
Bouziani Tayeb et al (2011) [7] studied the effect of marble powder content (MP) on the properties self compacting sand
concrete (SCSC) at fresh and hardened states. Values of slump flow, the V-funnel flow time and viscosity were found on fresh
concrete. At the hardened state, the 28th day compressive strength was found. The obtained test results showed that larger MP
content in SCSC (350 kg/m3) improved the properties at fresh state by decreasing V funnel flow time (from 5s 1.5s) and
increasing the slump flow values (from 28cm to 34cm). With the use of 250 kg/m3 of MP, the highest initial viscosity was
obtained while retaining good fluidity at high rotational speeds compared to the MP contents of 150 kg/m3 and 350 kg/m3. The
28 days compressive strength decreased with an increase of MP content.
Bahar Demirel (2010) [5] investigated the effects of using waste marble dust (WMD) as a fine material on the mechanical
properties of the concrete. For this purpose, four different series of concrete-mixtures were prepared by replacing the fine sand
(passing 0.25 mm sieve) with WMD at proportions of 0, 25, 50 and 100% by weight. In order to determine the effect of the
WMD on the compressive strength with respect to the curing age, compressive strengths of the samples were recorded at the
curing ages of 3, 7, 28 and 90 days. In addition, the porosity values, ultrasonic pulse velocity (UPV), dynamic modulus of
elasticity and the unit weights of concrete were determined. It was observed that replacement of the fine material passing through
a 0.25mm sieve with WMD at particular proportion has displayed an enhancing effect on compressive strength.
Felixkala.T and Partheeban.P (2010) [10] examined the possibility of using granite powder as replacement of sand along with
partial replacement of cement with fly ash, silica fume and blast furnace slag. They reported that granite powder of marginal
quantity as partial replacement to sand had beneficial effect on the mechanical properties such as compressive strength, split
tensile strength and modulus of elasticity. They also reported that the values of plastic and drying shrinkage of concrete with
granite powder were less than those of ordinary concrete specimens.
Compressive Strength Studies:
For Compressive strength test standard cube size of 150mm x 150mm x 150mm are used. An average of three specimens are
taken for all mixes after a curing period of 7 days & 28 days.
Table 1
Mean Compressive strength of M25 grade concrete:
Cement Fine Percentage replacement Compressive Compressive strength
Mix Coarse aggregate
used Aggregate in Fine Aggregate Strength at 28 days
Designation used
PPC used Copper slag Granite powder at 7 days N/mm2 N/mm2
M0 100% 100% ----- ----- 100% 15.22 31.80
MC15 100% 85% 15% ----- 100% 14.56 31.75
MC30 100% 70% 30% ----- 100% 15.63 32.04
MC40 100% 60% 40% ----- 100% 16.06 32.78
MG15 100% 85% ----- 15% 100% 15.04 28.65
MG30 100% 70% ----- 30% 100% 15.48 31.96
MG40 100% 60% ----- 40% 100% 15.96 32.25
MCG30 100% 70% 15% 15% 100% 15.84 24.85
MCG60 100% 40% 30% 30% 100% 15.71 30.08
MCG80 100% 20% 40% 40% 100% 18.10 33.43
Table 2
Mean Flexural strength of M25 grade concrete:
Percentage replacement
Mix Cement used Fine Aggregate Coarse aggregate Flexural strength
in Fine Aggregate
Designation PPC used used at 28 days N/mm2
Copper slag Granite powder
M0 100% 100% ----- ----- 100% 4.01
MC15 100% 85% 15% ----- 100% 4.08
MC30 100% 70% 30% ----- 100% 4.14
MC40 100% 60% 40% ----- 100% 4.20
MG15 100% 85% ----- 15% 100% 3.96
MG30 100% 70% ----- 30% 100% 3.86
MG40 100% 60% ----- 40% 100% 4.24
MCG30 100% 70% 15% 15% 100% 6.89
MCG60 100% 40% 30% 30% 100% 6.50
MCG80 100% 20% 40% 40% 100% 6.17
III. CONCLUSIONS
Maximum Compressive strength of concrete increased by 3.08% at 40% replacement of fine aggregate by copper slag, and
up to 40% replacement, concrete gain more strength than control mix concrete strength, except 15% replacement copper slag
concrete.
It is observed that for all percentage replacement of fine aggregate by Copper slag the flexural strength of concrete is more
than control mix.
It is observed that, the flexural strength of concrete at 28 days is higher than design mix (Without replacement) for 15%
replacement of fine aggregate by Copper slag, the flexural strength of concrete is increased by 1.74%. This also indicates
flexural strength is more for all percentage replacements than design mix. However, for 40% replacement of fine aggregate
by Copper slag concrete gives the maximum strength than control mix.
Compressive strength and flexural Strength is increased due to high toughness of Copper slag.
The compressive strength has increased by 1.41% with the use of 40% replacement of fine aggregates with granite powder.
concrete gain more strength than control mix concrete strength, except 15% replacement of granite powder concrete
It is observed that, the flexural strength of concrete at 28 days is higher than design mix (Without replacement) for 40%
replacement of fine aggregate by Granite powder, the flexural strength of concrete is increased by 5.73%. It shows that 40%
replacement of granite powder gives the maximum flexural strength, than remaining percentage replacements.
REFERENCES
[1] Janis Kazjonovs1, Diana Bajare2, Aleksandrs Korjakins Designing Of High Density Concrete by Using Steel Treatment Waste Riga Technical
University.
[2] High-Density Concrete for Gamma and Neutron Attenuation by T. E. Northup Oak Ridge National Laboratory Oak Ridge, Tennessee.
[3] Srinivas Allena1 and Craig M. Newtson2, Ultra-High Strength Concrete Mixtures Using Local Materials, New Mexico State University.
[4] Shielding Properties of Heavyweight, High Strength Concrete by M. Mahdya, P.R.S.Speareb, A. H. Abdel-Reheema A, Mansoura University.
[5] The Innovative Use of Modified High Desity Micro-Concrete for Radiation Shielding & Attenuation Jeet Digant Kapadia, Sourabh Surendra Manjrekar.