VX-160V 180V

VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan

VERTEX STANDARD
US Headquarters
VHF FM Transceiver 10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU EUROPE B.V.
VX-160V/-180V P.O. Box 75525, 1118 ZN Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Service Manual Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
2005 VERTEX STANDARD CO., LTD. EC013N90B Kwun Tong, Kowloon, Hong Kong
VX-160V VX-180V
Introduction
This manual provides technical information necessary for servicing the VX-160V and VX-180V FM Trans-
ceiver.
Servicing this equipment requires expertise in handling surface-mount chip components. Attempts by non-
qualified persons to service this equipment may result in permanent damage not covered by the warranty,
and may be illegal in some countries.
Two PCB layout diagrams are provided for each double-sided circuit board in the transceiver. Each side of
is referred to by the type of the majority of components installed on that side (leaded or chip-only). In
most cases one side has only chip components, and the other has either a mixture of both chip and leaded
components (trimmers, coils, electrolytic capacitors, ICs, etc.), or leaded components only.
While we believe the technical information in this manual to be correct, VERTEX STANDARD assumes no
liability for damage that may occur as a result of typographical or other errors that may be present. Your
cooperation in pointing out any inconsistencies in the technical information would be appreciated.
Contents
Operating Manual Reprint ............................ 2 Block Diagram ................................................. 9
Cloning .............................................................. 6 Circuit Description ................................11
Specifications ................................................... 7 Alignment .................................................13
Exploded View & Miscellaneous Parts ...... 8 Board Unit (Schematics, Layouts & Parts)
MAIN Unit ................................................................ 17
1
Operating Manual Reprint
Controls & Connectors Before You Begin
LED Indicator
Battery Pack Installation and Removal
Glows Green Monitor on U To install the battery, hold the transceiver with your
Blinking Green Busy Channel (or SQL off)
Glows Red Transmitting
left hand, so your palm is over the speaker and your
Blinking Red Battery Voltage is low thumb is on the top of the belt clip. Insert the battery
Blinking Yellow Receiving a Selective Call pack into the battery compartment on the back of the
Antenna
CH (Channel) Selector radio while tilting the Belt Clip outward, then close
VOL/PWR Knob the Battery Pack Latch until it locks in place with a
Click.
Push To Talk
(PTT) Switch MIC/SP Jack
(External Mic/Earphone)
Speaker
Monitor Button
LCD (VX-180)
Microphone U To remove the battery, turn the radio off and remove
any protective cases. Open the Battery Pack latch on
Soft KEY (VX-180)
the bottom of the radio, then slide the battery down-
ward and out from the radio while holding the Belt
Clip.
Battery Pack Latch
Caution!
Do not attempt to open any of the rechargeable Ni-
Cd packs, as they could explode if accidentally short-
circuited.
Display Icons & Indicators (VX-180 Only)
This indicator confirms that Low Battery Indication
DUAL WATCH is active.
U As the battery discharges during use, the voltage gradu-
This icon is the Low Battery in- This indicator confirms that ally becomes lower. When the battery voltage becomes
dicator, which appears when the this channel will be skipped
battery voltage becomes too low during scan. to low, substitute a freshly charged battery and recharge
for proper operation.
the depleted pack. The TX/BUSY indicator on the top
of the radio will blink red (on the VX-180, the
icon will appear on the LCD) when the battery voltage
is low.
U Avoid recharging Ni-Cd batteries often with little use
This indicator confirms that 8 Character Alpha-numeric between charges, as this can degrade the charge capac-
DUAL 2-TONE DECODE is active. Invertible Display ity. We recommend that you carry an extra, fully-
charged pack with you so the operational battery may
be used until depletion (this deep cycling technique
promotes better long-term battery capacity).
2
Operation
Preliminary Steps U Press and hold in the MONI-
U Install a charged battery pack onto the transceiver, as TOR key for more than 1 sec-
described previously. onds (or press the MONITOR
U Screw the supplied antenna onto the Antenna jack. key twice) to quiet the noise
Never attempt to operate this transceiver without an and resume normal (quiet)
antenna connected. monitoring.
U If you have a Speaker/Microphone, we recommend that
it not be connected until you are familiar with the ba- U To transmit, press and hold in
sic operation of the VX-160/-180. the PTT switch. Speak into the
microphone area of the front
Operation Quick Start panel grille (lower left-hand
U Turn the top panels VOL/ corner) in a normal voice level.
PWR knob clockwise to turn To return to the Receive mode,
on the radio on. release the PTT switch.
U If a Speaker/Microphone is available, remove the plas-
tic cap and its two mounting screws from the right side
of the transceiver, then insert the plug from the Speaker/
U Turn the top panels CH selec- Microphone into the MIC/SP jack; secure the plug us-
tor knob to choose the desired ing the screws supplied with the Speaker/Microphone.
operating channel. Hold the speaker grille up next to your ear while re-
ceiving. To transmit, press the PTT switch on the
Speaker/Microphone, just as you would on the main
transceivers body.
U Rotate the VOL/PWR knob to Note: Save the original plastic cap and its mounting
set the volume level. If no sig- screws. They should be re-installed when not us-
nal is present, press and hold ing the Speaker/Microphone.
in the MONITOR key (the
lower button on the left side)
for more than 1 seconds; back-
ground noise will now be heard, and you may use this
to set the VOL/PWR knob for the desired audio level.
Key Functions
The VX-180 provides programmable [A], [B], and [C] Function
Soft Key
function keys, and both the VX-160 and VX-180 provide [A] [B] [C] MONITOR key
None
programmable MONITOR keys. These Soft keys func- Monitor
tions can be customized (set to other functions), via pro- Low Power
gramming by your VERTEX STANDARD dealer, to meet Lock*
Lamp*
your communications/network requirements. Some fea-
Channel Up*
tures may require the purchase and installation of optional Channel Down*
internal accessories. The possible Soft key programming Scan
features are illustrated at the right, and their functions are Follow-me Scan
Dual Watch
explained in the next chapter. For further details, contact Talk Around
your VERTEX STANDARD dealer. Add/Del*
For future reference, check the box next to each function Call/Reset
Speed Dial
that has been assigned to the Soft key on your particular TX Save Off
radio, and keep it handy.
3
Description of Operating Functions
Monitor Follow-Me Scan
Press the assigned Soft key momentarily to override (dis- Follow-Me Scan feature checks a User-assigned Prior-
able) the Tone squelch. ity Channel regularly as you scan the other channels. Thus,
Background noise or incoming signals will now be heard if only Channels 1, 3, and 5 (of the 8 available channels)
whether or not a matching tone is present on the signal). are designated for Scanning, the user may nonetheless
Press and hold in the assigned Soft key for more than 1 assign Channel as the User-assigned Priority Channel
seconds to override both the Noise and Tone squelch. Again via the Follow-Me feature.
press and hold in the assigned Soft key for more than 1 Press the assigned Soft key to activate Follow-Me scan-
seconds (or press the assigned Soft key twice) to resume ning, then turn the CH selector knob to the channel which
normal (quiet) Noise and Tone squelch action. you want to designate as the User-Assigned Priority Chan-
nel. When the scanner stops on an active channel, the
Low Power User-assigned Priority Channel will automatically be
Press the assigned Soft key to set the radio's transmitter checked every few seconds.
to the Low Power mode, thus extending battery life.
Press the assigned Soft key again to return to High Dual Watch
Power operation when in difficult terrain. The Dual Watch feature is similar to the Scan feature, ex-
cept that only two channels are monitored: the current
Lock operating channel, and the Priority channel.
Press the assigned Soft key to lock the Soft keys (except U To activate Dual Watch:
Lock and Monitor key); thus, the [A], [B], [C], and MONI- Press the assigned Soft key.
TOR keys can be disabled to prevent radio settings from The scanner will search the two channels; it will pause
being disturbed. each time it finds a channel on which someone is speak-
Lamp ing.
Press the assigned Soft key to illuminate the LCD for U To stop Dual Watch:
five seconds. Press the assigned Soft key.
Operation will revert to the channel to which the CH
Channel Up knob is set.
Press the assigned Soft key to switch to a higher operat-
ing channel number. Talk Around
Press the assigned Soft to activate the Talk Around fea-
Channel Down ture when you are operating on duplex channel systems
Press the assigned Soft key to switch to a lower operating (separate receive and transmit frequencies, utilizing a re-
channel number. peater station). The Talk Around feature allows you to
Scan bypass the repeater station and talk directly to a station
The Scanning feature is used to monitor multiple chan- that is nearby. This feature has no effect when you are
nels programmed into the transceiver. While scanning, the operating on Simplex channels, where the receive and
radio will check each channel for the presence of a signal, transmit frequencies are already the same.
and will stop on a channel if a signal is present. Note that your dealer may have made provision for Talk
U To activate scanning: Around channels by programming repeater and Talk
Press the assigned Soft key. Around frequencies on two adjacent channels. If so, the
The scanner will search the channels, looking for ac- key may be used for one of the other Pre-Programmed
tive ones; it will pause each time it finds a channel on Functions.
which someone is speaking. Add/Del
U To stop scanning: The Add/Del feature allows the user to arrange a custom
Press the assigned Soft key. Scan.
Operation will revert to the channel to which the CH Press the assigned Soft key to delete/restore the current
knob is set. channel to/from your scanning list.
When you delete a current channel, SKIP will appear
on the LCD after pressing the Soft key. When you re-
store a current channel, SKIP indicator on the LCD will
turn off.
4
Description of Operating Functions
Call/Reset TX Save Off
When the 2-tone selective calling unit is installed, press Press the assigned Soft key to disable the Transmit Bat-
the assigned Soft key to silence the receiver and reset for tery Saver, if you are operating in a location where high
another call, when a communication is finished. power is almost always needed.
The Transmit Battery Saver helps extend battery life by
Speed Dial reducing transmit power when a very strong signal from
Your Dealer may have pre-programmed Auto-Dial tele- an apparently nearby station is being received. Under some
phone number memories into your radio. circumstances, though, your hand-held radio may not be
To dial a number, just press the Dealer-assigned Soft key heard well at the other end of the communication path,
for Speed Dialing. The DTMF tones sent during the dial- and high power may be necessary at all times.
ing sequence will be heard in the speaker.
Accessories & Options

FNB-64 7.2 V 700 mAh Ni-Cd Battery
FNB-V57 7.2 V 1100 mAh Ni-Cd Battery
FBA-25A Alkaline Battery Case
NC-77B 120 VAC Overnight Desktop Charger
NC-77C 230-240 VAC Overnight Desktop Charger
VAC-800 Desktop Rapid Charger
VAC-6800 6-unit Multi Charger
MH-45B4B Speaker/Microphone
MH-37A4B Earpiece Microphone
VC-25 VOX Headset
VCM-1 Mobile Mounting Bracket (for VAC-800)
LCC-160/S Leather Case (for VX-160)
LCC-180/S Leather Case (for VX-180)
CT-42 PC Programming Cable
CT-27 Radio to Radio Programming Cable
CE44 Programming Software
5
Cloning
The VX-160/-180 includes a convenient Cloning feature, which allows the programming data from one transceiver to
be transferred to another VX-160/-180. Here is the procedure for Cloning one radio's data to another.
1. Turn both transceivers off. 6. Press the PTT switch on the source transceiver; SEND-
SEND-
2. Remove the plastic cap and its two mounting screws ING will appear on the Source transceiver (for VX-
ING
from the MIC/SP jack on the right side of the trans- 180; for VX-160, the TX/BUSY indicator on the top
ceiver. Do this for both transceivers. of the radio will glow Red), and the data will be trans-
3. Connect the optional CT-27 cloning cable between the ferred.
MIC/SP jacks of the two transceivers. 7. If there is a problem during the cloning process, ER- ER-
4. Press and hold in the PTT and MONITOR switches ROR will appear on the LCD (for VX-180; for VX-
ROR
(just below the PTT switch) while turning the trans- 160, the TX/BUSY indicator on the top of the radio
ceiver on. Do this for both transceivers (the order of will blink Red); check your cable connections and bat-
the switch-on does not matter). CLONE
CLONE will appear
CLONE tery voltage, and try again.
on the displays (for the VX-180) of both transceivers 8. If the data transfer is successful, the display will return
when Clone mode is successfully activated in this step; CLONE (for VX-180; for VX-160, the TX/BUSY
to CLONE
CLONE
in the case of the VX-160, no change will be observed indicator on the top of the radio will turn off). Turn
at this point. both transceivers off and disconnect the CT-27 cable.
5. On the Destination transceiver, press the MONITOR You can then turn the transceivers back on, and begin
LOADING will appear on the LCD (for VX-
switch. LOADING
LOADING normal operation.
180; for VX-160, the TX/BUSY indicator on the top 9. Replace the plastic cap and its two mounting screws.
of the radio will glow Green).
Optional Cloning Cable CT-27
6
Specifications
GENERAL Specifications
Frequency Range (MHz): 134 - 160 (TYP A)
146 - 174 (TYP C)
142 - 176 (TYP CS1)
Number of Channels: 16 channels
Channel Spacing: 12.5 / 25 kHz (15 / 30 kHz)
PLL Steps 2.5 / 6.25 kHz
Power Supply voltage: 7.5 VDC 20%
Operating Temperature Range: 22F to +140F (30C to +60C)
Frequency Stability: 2.5 ppm
Dimensions (WHD): 2.3" (W) x 4.7" (H) x 1.2" (D) (58 x 120 x 31 mm)
Weight (approx.): 0.81 lb. (365 g) w/FNB-64
RECEIVER Specifications (Measurements made per EIA standard TIA/EIA-603)

Sensitivity
EIA 12 dB SINAD : 0.20 V
20 dB Quieting : 0.30 V
Adjacent channel selectivity: 65 dB (25 kHz) / 60 dB (12.5 kHz)
Intermodulation: 65 dB
Spurious and Image Rejection: 65 dB
Hum & Noise 45 dB
Audio output: 500 mW @4 Ohms, 5% THD
TRANSMITTER Specifications (Measurements made per EIA standard TIA/EIA-603)

Power output: 5.0 / 1.0 W
Modulation: 16K0F3E, 11K0F3E
Conducted Spurious Emissions: 60 dB Below Carrier
FM Hum & Noise: 40 dB (25 kHz) / 35 dB (12.5 kHz)
Audio distortion (@ 1 kHz): <5%
Measurements per EIA standards unless noted above. Specifications subject to change without notice or obligation.
7
Exploded View & Miscellaneous Parts
RA0173500
CP8266003 (VTX: Lot. 102~)
CAP CP8266004 (EXP: Lot. 102~)
RA029600C (Lot. 56~101)
RA029600B (Lot. 28~55)
RA029600A (Lot. 17~27)
RA0296000 (Lot. 1~16)
R6147510 FRONT CASE ASSY (VX-160)
RING NUT (x 2 pcs)
RA0296100
VOLUME KNOB RA0210900
RA021100B (Lot. 10~) WINDOW
RA021100A (Lot. 1~9)
DOUBLE FACE TAPE
RA0294400
RA0309800 (Lot. 20~) LCD HOLDER (VX-180)
RA029620A (Lot. 3~) MYLAR SHEET (SP)
RA0296200 (Lot. 1~2) RA029450B (Lot. 76~)
G6090139 RA029450A (Lot. 10~75)
KNOB (CH) LCD (VX-180)
RA0210600 RA0294500
RUBBER PACKING (x 2 pcs) LIGHT GUIDE (VX-180)
RA0334900
REFLECTOR SHEET (VX-180)
RA0294800 RA0293900
INTER CONNECTOR (VX-180) RUBBER KNOB

MAIN Unit
RA0110200
HOLDER RUBBER
CP8266002 (VTX: Lot 102~)
CP8266006 (EXP: Lot 102~)
RA0351700 RA029590D (Lot. 54~101)
TERMINAL PLATE (+) RA029590C (Lot. 28~53)
RA029590B (Lot. 17~27)
RA010340B (Lot. 28~) RA0295900 (Lot. 1~16)
RA010340A (Lot. 1~27) FRONT CASE ASSY (VX-180)
TERMINAL HOLDER (w/WINDOW, DOUBLE FACE TAPE)
RA0351600 RA055770B (Lot. 98~)
TERMINAL PLATE (-) LATCH NAIL C
RA0123500 (Lot. 1~97)
LATCH NAIL B
RA029430A (Lot. 4~)

RA0294300 (Lot. 1~3)
RUBBER PACKING CP8264001 (Lot. 96~)
RA029310D (Lot. 26~96)
RA029310C (Lot. 20~25)
RA029310B (Lot. 11~19)
RA029310A (Lot. 3~10)
RA0293100 (Lot. 1~2)
P1091034A REAR CASE ASSY
(w/SMA CONNECTOR, TERMINAL PLATE (-),
CONNECTOR SMA/BR-1 PAN HEAD SCREW M2X3NI)
CAUTION
REF. VXSTD P/N Description Qty.
U44104002 TAPTITE SCREW M2X4NI 10
U44104002
TAPTITE SCREW M2X4NI 2
(VX-180V)
U20206007 BINDING HEAD SCREW M2.6X6B 2
U24110002 TAPTITE SCREW M2X10NI 2
U02206007 SEMS SCREW SM2.6X6B 2
U00103002 PAN HEAD SCREW M2X3NI 1
CP7064001
BELT CLIP ASSY
8
Block Diagram
9
Note:
10
Circuit Description
Receive Signal Path Squelch Control
Incoming RF from the antenna jack is delivered to the The squelch circuitry consists of a noise amplifier and
RF Unit and passes through a low-pass filter consisting of band-pass filter within Q1037, and noise detector D1018
coils L1001, L1002, and L1031, capacitors C1004, C1005, (HVC358B).
C1008, C1010, C1014, C1016, and C1221, and antenna When no carrier is received, noise at the output of the
switching diode D1003 (RLS135 TE-17). detector stage in Q1037 is amplified and band-pass fil-
Signals within the frequency range of the transceiver tered by the noise amplifier section of Q1037 and the net-
enter a varactor-tuned band-pass filter consisting of coils work between pins 7 and 8, and then is rectified by D1028.
L1010 and L1011, capacitors C1044, C1046, C1060, The resulting DC squelch control voltage is passed to
C1065, and C1068, and diodes D1011, D1012, D1013, pin 37 of the microprocessor Q1014 (M37516E6HP:Lot.
and D1014 (all HVC358B), then are amplified by Q1012 1~4, M37516M6:Lot. 5~). If no carrier is received, this
(2SC5006-T1) and enter a varactor-tuned band-pass fil- signal causes pin 24 of Q1014 to go high and pin 20 to go
ter consisting of coils L1017 and L1021, capacitors C1084, high. Pin 24 signals Q1060 (RT1P441U-T11-1) to dis-
C1086, C1095, and C1097, and diodes D1018, D1019 able the supply voltage to the audio amplifier Q1039, while
(both HVC358B), before mixing by first mixer Q1026 pin 20 holds the green (Busy) half of the LED off, when
(SGM2016AM-T7). pin 24 is high and pin 20 is high.
Buffered output from the VCO is amplified by Q1007 Thus, the microprocessor blocks output from the au-
(2SC5005-T1) to provide a pure first local signal between dio amplifier, and silences the receiver, while no signal is
190.25 and 218.25 MHz for injection to the first mixer. being received (and during transmission, as well).
The 44.25 MHz first mixer product then passes through When a carrier appears at the discriminator, noise is re-
monolithic crystal filter XF1002 (typ A, C:HDF0042, 5.5 moved from the output, causing pin 37 of Q1014 to go low
kHz BW or typ CS1:HDF0051) to strip away unwanted and the microprocessor to activate the Busy LED via Q1014.
mixer products, and the IF signal is then amplified by The microprocessor then checks for CTCSS or CDCSS
Q1033 (2SC4215Y TE85R). code squelch information, if enabled. If not transmitting
The amplified first IF signal is applied to FM IF sub- and CTCSS or CDCSS is not activated, or if the received
system IC Q1037 (TA31136FN-EL), which contains the tone or code matches that programmed, audio is allowed
second mixer, second local oscillator, limiter amplifier, to pass through the audio amplifier Q1039 (NJM2070M
noise amplifier, and RSSI amplifier. TE2) to the loudspeaker by the enabling of the supply
The second local signal is produced from the PLL ref- voltage to it via Q1037.
erence/second local oscillator of 14.60 MHz crystal X1001.
The 14.60 MHz reference signal is tripled by Q1036, ca- Transmit Signal Path
pacitor C1209, and coil L1029, and the resulting 43.8 MHz Speech input from the microphone is amplified by
second local signal is then delivered to the mixer section Q1017 (NJM2902V TE1); after pre-emphasis by C1066
of Q1037, which produces the 450 kHz second IF when and R1054, the audio is amplified in another section of Q1017.
mixed with the first IF signal. The processed audio may then be mixed with a CTCSS
The second IF then passes through ceramic filter tone generated by Q1014 (M37516E6HP:Lot. 1~4,
CF1001 (ALFYM450G=K on Narrow channels) or M37516M6:Lot. 5~) for frequency modulation of the PLL
CF1002 (ALFYM450F=K on Wide channels) to strip carrier (up to 5 kHz from the unmodulated carrier) at the
away all but the desired signal, and then is applied to the transmitting frequency.
limiter amplifier in Q1037, which removes amplitude If a CDCSS code is enabled for transmission, the code is
variations in the 450 kHz IF, before detection of the speech generated by microprocessor Q1014 (M37516E6HP:Lot.
by the ceramic discriminator, CD1001 (CDBC450CX24). 1~4, M37516M6:Lot. 5~) and delivered to D1004
Detected audio from Q1037 is applied to the audio high- (HVC350B TRF) for CDCSS modulating.
pass filter, and then passes via the volume control to the The modulated signal from the VCO Q1002
audio amplifier Q1039 (NJM2070M-TE2), which pro- (2SC5231C8-TL) is buffered by Q1007 (2SC5005-T1).
vides up to 1/2 Watt to the optional headphone jack or a 4- The low-level transmit signal then passes through the T/R
ohm loudspeaker. switching diode D1016 (DAN235E-TL) to driver ampli-
fiers Q1015 (2SC5227-4-TB) and Q1016
(2SK2596BXTL), then the amplified transmit signal is
applied to the final amplifier Q1024 (2SK2974-T11),
which delivers up to 5 watts of output power.
The transmit signal then passes through the antenna
switch D1003 (RLS135 TE-11) and is low-pass filtered,
to suppress harmonic spurious radiation, before delivery
to the antenna.
11
Circuit Description
Automatic Transmit Power Control The data latch section of Q1005 also receives serial
Current from the final amplifier is sampled by R1108, dividing data from the microprocessor, Q1014, which
R1115, and R1125, and is rectified by Q1057 (IMZ2A causes the pre-divided VCO signal to be further divided
T108). The resulting DC is fed back through Q1032 in the programmable divider section, depending upon the
(FMW1 T98) to the drive amplifier Q1016 and final am- desired receive frequency, so as to produce a 2.5 kHz or
plifier Q1024, for control of the power output. 3.125 kHz derivative of the current VCO frequency.
The microprocessor selects High or Low power levels. Meanwhile, the reference divider section of Q1005
divides the 14.60 MHz crystal reference (from the refer-
Transmit Inhibit ence oscillator, Q1022) by 5840 (or 4672) to produce the
When the transmit PLL is unlocked, pin 7 of PLL chip 2.5 kHz (or 3.125 kHz) loop references (respectively).
Q1005 goes to a logic Low, and unlock detector Q1056 The 2.5 kHz (or 3.125 kHz) signal from the program-
(2SA1586Y TE85R) goes to a logic High. The result- mable divider (derived from the VCO) and that derived
ing DC unlock control voltage is passed to pin 14 of the from the reference oscillator are applied to the phase de-
microprocessor, Q1014. While the transmit PLL is un- tector section of Q1004, which produces a pulsed output
locked, pin 22 of Q1014 remains high, which then turns with pulse duration depending on the phase difference
off Q1029 (CPH6102-TL) and the Automatic Power Con- between the input signals.
troller Q1032 (FMW1 T98) to disable the supply voltage This pulse train is filtered to DC and returned to the
to the drive amplifiers Q1015/Q1016 and final amplifier varactor D1037 and D1042 (both, typ A, C:HVC358B or
Q1024, thereby disabling the transmitter. typ CS1:1SV305). Changes in the level of the DC volt-
age are applied to the varactor, affecting the reference in
Spurious Suppression the tank circuit of the VCO according to the phase differ-
Generation of spurious products by the transmitter is ence between the signals derived from the VCO and the
minimized by the fundamental carrier frequency being crystal reference oscillator.
equal to final transmitting frequency, modulated directly The VCO is thus phase-locked to the crystal reference
in the transmit VCO. Additional harmonic suppression is oscillator. The output of the VCO Q1002, after buffering
provided by a low-pass filter consisting of coils L1001, by Q1007, is applied to the first mixer as described previ-
L1002, and L1031 plus capacitors C1004, C1005, C1008, ously.
C1010, C1014, C1016, and C1221, resulting in more than For transmission, the VCO Q1002 oscillates between
60 dB of harmonic suppression prior to delivery of the RF 146 and 174 MHz according to the model version and
signal to the antenna. programmed transmit frequency. The remainder of the PLL
circuitry is shared with the receiver. However, the divid-
PLL Frequency Synthesizer ing data from the microprocessor is such that the VCO
The PLL circuitry on the Main Unit consists of VCO frequency is at the actual transmit frequency (rather than
Q1002 (2SC5231C8-TL), VCO buffer Q1007 offset for IFs, as in the receiving case). Also, the VCO is
(2SC5005), and PLL subsystem IC Q1005 modulated by the speech audio applied to D1005 (typ
(MB15A02PFV1-G-BND-EF), which contains a refer- A: H V U 3 5 8 T R F , typ C: 1 S V 2 2 9 T P H 3 , typ
ence divider, serial-to-parallel data latch, programmable CS1:1SV229 TPH3:Lot. 45~, HVU358 TRF:Lot. 54~),
divider, phase comparator, and charge pump. as described previously.
Frequency stability is maintained by temperature com- Receive and transmit buses select which VCO is made
pensating thermistor TH1004. The output from TH1004 active, using Q1059 and Q1063 (both RT1P441U-T11-
is applied to pin 39 of Q1014. Q1014 outputs thermal data 1).
to D/A converter Q1052 (M62364FP 600D), which pro-
duces a DC voltage corresponding to the thermal data. Miscellaneous Circuits
The resulting DC voltage is applied to varactor diode Push-To-Talk Transmit Activation
D1004 (HVC350B TRF) to stabilize the 14.60 MHz Ref- The PTT switch on the microphone is connected to pin
erence Frequency. 48 of microprocessor Q1014, so that when the PTT switch
While receiving, VCO Q1002 oscillates between is closed, pin 23 of Q1014 goes low. This signal disables
190.25 and 218.25 MHz according to the transceiver ver- the receiver by disabling the 5 V supply bus at Q1036
sion and the programmed receiving frequency. The VCO (DTB123EK T146) to the front-end, FM IF subsystem
output is buffered by Q1007, then applied to the prescaler IC Q1037, and the receiver VCO circuitry.
section of Q1005. There the VCO signal is divided by 64 At the same time, Q1027 (FMW1 T98) and Q1029
or 65, according to a control signal from the data latch (CPH6102-TL) activate the transmit 5V supply line to
section of Q1005, before being sent to the programmable enable the transmitter.
divider section of Q1005.
12
Alignment
Introduction Required Test Equipment
The VX-160/-180 has been aligned at the factory for U Avionics Radio Tester with calibrated output level at
the specified performance across the entire frequency range 500 MHz
specified. Realignment should therefore not be necessary U In-line Wattmeter with 5% accuracy at 500 MHz
except in the event of a component failure. All component U 50-ohm, 10-W RF Dummy Load
replacement and service should be performed only by an U Regulated DC Power Supply (standard 7.5V DC, 2A)
authorized Vertex Standard representative, or the warranty U Frequency Counter: 0.2 ppm accuracy at 500 MHz
policy may be voided. U AF Signal Generator
The following procedures cover the sometimes critical U AC Voltmeter
and tedious adjustments that are not normally required once U DC Voltmeter
the transceiver has left the factory. However, if damage U UHF Sampling Coupler
occurs and some parts are replaced, realignment may be U IBM PC/compatible Computer with Microsoft DOS
required. If a sudden problem occurs during normal op- v3.0 or later operating system
eration, it is likely due to component failure; realignment U Vertex Standard CT-42 Connection Cable and CE44
should not be done until after the faulty component has Alignment program
been replaced.
We recommend that servicing be performed only by Alignment Preparation & Precautions
authorized Vertex Standard service technicians who are A 50-ohm RF Dummy load and in-line wattmeter must
experienced with the circuitry and fully equipped for re- be connected to the main antenna jack in all procedures
pair and alignment. Therefore, if a fault is suspected, con- that call for transmission, except where specified other-
tact the dealer from whom the transceiver was purchased wise. Correct alignment is not possible with an antenna.
for instructions regarding repair. Authorized Vertex Stan- After completing one step, read the following step to
dard service technicians realign all circuits and make com- determine whether the same test equipment will be re-
plete performance checks to ensure compliance with fac- quired. If not, remove the test equipment (except dummy
tory specifications after replacing any faulty components. load and wattmeter, if connected) before proceeding.
Those who do undertake any of the following alignments Correct alignment requires that the ambient tempera-
are cautioned to proceed at their own risk. Problems caused ture be the same as that of the transceiver and test equip-
by unauthorized attempts at realignment are not covered ment, and that this temperature be held constant between
by the warranty policy. Also, Vertex Standard must re- 20 and 30C (68~ 86F). When the transceiver is brought
serve the right to change circuits and alignment proce- into the shop from hot or cold air, it should be allowed
dures in the interest of improved performance, without time to come to room temperature before alignment.
notifying owners. Under no circumstances should any Whenever possible, alignments should be made with
alignment be attempted unless the normal function and oscillator shields and circuit boards firmly affixed in place.
operation of the transceiver are clearly understood, the Also, the test equipment must be thoroughly warmed up
cause of the malfunction has been clearly pinpointed and before beginning.
any faulty components replaced, and the need for realign-
Note:Signal levels in dB referred to in this procedure are
ment determined to be absolutely necessary. The follow-
based on 0 dB = 0.5 V (closed circuit).
ing test equipment (and thorough familiarity with its cor-
rect use) is necessary for complete realignment. Correc-
Important Note
tion of problems caused by misalignment resulting from
use of improper test equipment is not covered under the When connecting the CT-42 plug into the MIC/SP
warranty policy. While most steps do not require all of the jack of the VX-160/-180, you must remove the plas-
equipment listed, the interactions of some adjustments may tic cap and its mounting screws prior to programming.
require that more complex adjustments be performed af- Please remember to re-attach the cap and screws when
terwards. Do not attempt to perform only a single step the programming is complete.
unless it is clearly isolated electrically from all other steps.
Have all test equipment ready before beginning, and fol-
low all of the steps in a section in the order presented.
13
Alignment
Set up the test equipment as shown below for trans- The alignment tool outline
ceiver alignment, and apply 7.5V DC power to the trans- Installation of the Alignment tool
ceiver. The alignment mode is a software-based protocol,
accessed by an Alignment Mode command from the
50-ohm computer while switching the transceiver on.It is oper-
Dummy Load ated by the alignment tool automatically. During use of
RF Signal the alignment mode, normal operation is suspended. The
Generator
alignment tool program provides all needed operation ca-
Inline Wattmeter
pability.
The alignment tool consists of an executable file
RF Sampling CE44.exe and an accmpanying configuration file
Deviation Meter Transceiver
Coupler CE44.cfg which should be loaded per standard DOS
CT-42 connection MIC/SP procedures. Create a suitable directory, then copy these
Cable
Frequency foles from the distribution diskette into the new directory.
Power Supply
Counter PC 7.5V DC For example, if copying the file from Drive A, use the
COM port following DOS command sequence:
c:\ mkdir align [enter]
c:\ cd align [enter]
The transceiver must be programmed for use in the c:\ align\ copy a:ce44.*
intended system before alignment is attempted. The RF
parameters are loaded from the file during the alignment No further installation steps are required. If you wish
process. to utilize a different name for the alignment directory, it
In order to facilitate alignment over the complete op- will not matter to the executable file.
erating rang of the equipment, it is recommended that the Booting the Alignment Tool
channel data in the transceiver be preset as per the chart Change to the align directory (or the directory name
below. you utilized in the previous section). Now type on the com-
mand line: ce44 ENTER to boot the alignment tool.
Frequency (MHz) The introductory screen will appear, and you may press
Channels any key to enter the main screen.
Ver. A Ver. C Ver. CS1
Low Band Edge 134.000 146.000 142.000 Entering Alignment Mode
(Channel 1) (Low POWER) (Low POWER) (Low POWER) To enter the alignment mode, turn the transceiver off,
Band Center 147.000 160.000 159.000 Select Radio then Adjust parameter. Now, turn the
(Channel 2) (High POWER) (High POWER) (High POWER)
transceiver back on. When the command has been suc-
cessful, a message on the computer screen will confirm
High Band Edge 160.000 174.000 176.000
that the transceiver is now in the Alignment mode.
(Channel 3) (High POWER) (High POWER) (High POWER)
Alignment Sequence
Although the data displayed on the computer's screen
Tone-Frequency (Hz) / DCS-code
during alignment is temporary data, it is important you
Channel Ver. A Ver. C Ver. CS1 follow the basic alignment sequence precisely, so that the
CTCSS DCS CTCSS DCS CTCSS DCS displayed data and the data loaded into the transceiver are
Low Band Edge identical.
Basic Alignment Sequence
(Channel 1)
Band Center 1. Enter the alignment mode
151.4 151.4 151.4 2. Upload data from transceiver
(Channel 2)
3. Align data
High Band Edge 4. Download data to transceiver
627 627 627
(Channel 3)
14
Alignment
PLL VCV (Varactor Control Voltage) MIC Sensitivity
U Connect the DC voltmeter between TP3 on the Main U Set the transceiver to CH 2 (band center).
Unit and ground. U Inject a 1 kHz tone at 37 dBm to the MIC jack.
U Set the transceiver to CH 3 (high band edge), and ad-
just L1004 on the Main Unit for 3.7~3.8 V (Typ C),
CLONE GND
3.0~3.1 V (Typ CS1) or 3.4~3.5 V (Typ A) on the DC
voltmeter.
SP
Transmitter Output Power IN

High Power
U Set the transceiver to CH 2 (band center).
U Open the Adjust
Adjust window on the CE44 program, then
Adjust
select the RF (High) parameter.
RF Power (High) U Open the Adjust
Adjust window on CE44, then select the
Adjust
U Press the [ENTER] key to enable programming of this MIC Sensitivity parameter.
MIC Sensitivity
parameter; use the [] or [] arrow keys so that the U Press the [ENTER] key to enable programming of this
power meter reading is 5.5 W 0.1 W (Typ C, CS1) or parameter; use the [] or [] arrow keys so that the
5.0 W 0.1 W (Typ A). Confirm that the current con- deviation meter reading is 3.0 kHz (0.1 kHz) (for 25
sumption is 2.2 A or lower. kHz steps) deviation.
U Press the [ENTER] key to lock in the new data. U Press the [ENTER] key to lock in the new data.
Low Power
U Set the transceiver to CH 1 (Low band edge).
U Open the Adjust
Adjust window on the CE44 program, then
Adjust
select the RF (Low) parameter.
RF Power (Low)
U Press the [ENTER] key to enable programming of this
parameter; use the [] or [] arrow keys so that the
power meter reading is 1.0 W 0.1 W (for RF Power
Low). Confirm that the current consumption is 1.0 A
or lower.
U Press the [ENTER] key to lock in the new data.
TP3 L1004
15
Alignment
MAX Deviation RF Frequency
U Set the transceiver to CH 2 (band center). U Set the transceiver to CH 2 (band center).
U Inject a 1 kHz tone at 17 dBm to the MIC jack. U Open the Adjust
Adjust
U Open the Adjust
Adjust RF Frequency parameter.
RF Frequency
MAX Deviation parameter.
MAX Deviation U Press the [ENTER] key to enable programming of this
U Press the [ENTER] key to enable programming of this parameter; use the [] or [] arrow keys so that the
parameter; use the [] or [] arrow keys so that the frequency counter displays the band center frequency
deviation meter reading is 4.2 kHz (0.1 kHz) (for 25 (100 Hz) for the version being aligned.
kHz steps, Typ A, C), 4.3 kHz (0.1 kHz) (for 25 kHz U Press the [ENTER] key to lock in the new data.
steps, Typ CS1) or 2.1 kHz (0.1 kHz) (for 12.5 kHz
steps) deviation. Sensitivity
U Press the [ENTER] key to lock in the new data. U Set the transceiver to CH 3 (high band edge, Typ C, A)
or CH 1 (low band edge, Typ CS1).
CTCSS Deviation U Tune the RF signal generator to the same frequency as
U Set the transceiver to CH 2 (band center). the transceivers, then set the generator output level to
U Open the Adjust
Adjust 40 dB with 3.0 kHz deviation @ 1 kHz tone modu-
CTCSS Deviation parameter.
CTCSS Deviation lation.
U Press the [ENTER] key to enable programming of this U Open the Adjust
Adjust
parameter; use the [] or [] arrow keys so that the RX Tune parameter.
RX Tune
deviation meter reading is 0.7 kHz (0.1 kHz) (for 25 U Press the [ENTER] key to enable programming of this
kHz steps, Typ C, A), 0.9 kHz (0.1 kHz) (for 25 kHz parameter. Use the [] or [] arrow keys to tune for
steps, Typ CS1) or 0.35 kHz (0.1 kHz) (for 12.5 kHz best sensitivity; ultimately, the radio should be aligned
steps, Typ C, A), 0.5 kHz (0.1 kHz) (for 12.5 kHz so that the RF signal generator output level is 6 dB
steps, Typ CS1)deviation. EMF (0.25 V) or less for 12 dB SINAD.
U Press the [ENTER] key to lock in the new data. U Press the [ENTER] key to lock in the new data.
DCS Deviation
U Set the transceiver to CH 3 (high band edge).
U Open the Adjust
Adjust
DCS Deviation parameter.
DCS Deviation
U Press the [ENTER] key to enable programming of this
parameter; use the [] or [] arrow keys so that the
deviation meter reading is 0.75 kHz (0.1 kHz) (for
25 kHz steps) or 0.35 kHz (0.1 kHz) (for 12.5 kHz
steps) deviation.
U Press the [ENTER] key to lock in the new data.
16
Circuit Diagram MAIN Unit (Lot. 1~2)
SQL Open:2.78V
SQL Close:2.78V
SQL Open:0.73V
SQL Close:0.74V SQL Open:0.0V
SQL Close:0.0V SQL Open:1.97V
SQL Close:1.97V
SQL Open:0.73V SQL Open:0.0V

SQL Close:0.73V SQL Close:0.0V
<2.07V>
{0.74V}
<5.04V>
{5.04V}
3.91V
(3.91V) 5.08V Wide:0.0V
2.76V (0.0V) <2.04V>
(2.80V) Narrow:0.0V
0.0V <7.18V> {0.72V}
3.33V (5.0V) Wide:4.98V
(3.38V) {7.37V} <2.7V> Narrow:0.0V
Wide:4.97V Narrow:1.22V Wide:3.13V
{1.35V}
Wide:4.97V Narrow:1.87V
Narrow:1.19V
2.7V
2.17V 0.78V (4.32V) <2.61V>{1.34V}
(2.28V) (0.24V) 3.47V 0.0V
(0.0V) (0.71V) 0.0V <2.07V> {0.75V}
<6.6V>
{6.77V} Wide:3.15V Wide:3.71V Wide:3.71V
0.0V Narrow:1.9V Narrow:0.0V Narrow:0.0V
(0.0V) 0.0V <6.6V>
(0.0V) {6.77V} 5.0V
<7.22V>
{7.36V} <7.2V>
{7.34V} 1.27V 1.27V
4.21V
4.19V (4.26V)
(0.0V)
1.25V
5.0V
5.07V
(5.11V) 5.0V
(5.0V)
1.24V
4.21V
(4.26V) 1.24V
0.0V
(4.21V) 2.48V
4.9V
(4.94V)
0.0V
(4.95V)
5.0V
0.0V 5.0V
(3.75V) 2.49V 2.94V
(4.21V)
5.0V 1.56V
1.57V
(0.0V)
7.52V
5.0V
LED On:4.27V 2.44V
0.0V LED Off:4.63V 5.0V
(0.0V) (5.0V)
LED On:2.77V 1.56V

LED Off:0.0V 1.59V
0.0V 1.57V
4.99V
(4.99V)
4.84V 3.23V
(4.84V) (3.23V) 1.55V
1.02V
0.0V
(0.0V) 4.99V
7.5V
(7.27V) 2.92V
SQL Open:0.59V SQL Close:0.9V

SQL Open:3.43V
SQL Close:0.04V
5.0V
(4.86V)
4.92V
4.73V 5.0V
(4.2V) (4.95V)
2.1V
SQL Open: 5.0V 0.0V

0.6V (4.22V) (4.84V)
SQL Close:
5.0V
SQL Open:5.0V
SQL Close:5.0V
SQL Open:5.0V SQL Open:6.83V
SQL Close:0.0V SQL Close:
7.5V
SQL Open:0.7V
SQL Close:0.0V
0.0V
7.5V <7.33V> {7.43V}
0.0V <5.07V> SQL Open:0.26V SQL Close:7.5V

{5.06V}
SQL Open:7.5V
5.0V SQL Close:0.21V
(5.0V) 5.0V (0.0V)
5.0V
5.0V 4.99V SQL Open:7.5V
4.97V (5.0V) (7.35V)
(5.0V) SQL Close:7.5V
0.0V
0.0V (0.0V)
7.5V 7.5V
(2.27V) 7.5V
0.0V (7.31V) (7.38V)
(6.64V) 6.96V
5.0V 5.0V (6.75V)
5.0V (0.0V) 5.0V
(5.0V) (5.0V)
(5.0V)
0.0V
(2.29V) (2.30V) (2.29V) (5.0V)
(2.31V)
5.0V
5.0V (5.0V) 5.06V
(4.42V) 4.43V (5.09V)
0.0V (4.46V)
(2.27V) (5.0V)
Q1005
SQL Close SQL Open TX High
(2.31V) 1 -- -- --
(2.27V) RX : XX Q1037 2 -- -- --
(0.0V) (2.24V) TX : XX SQL Open
(2.26V) TX HIGH : <XX> 3 5.00V 5.00V 5.0V
TX LOW : {XX} 1 4.98V 9 1.11V 4 4.77V 4.77V 4.78V
(2.31V) 2 4.72V 10 5.00V 5 2.53V 2.53V 2.11V
(2.31V) 3 3.81V 11 4.14V 6 0.0V 0.0V 0.0V
4 5.02V 12 0.55V 7 4.77V 4.77V 4.77V
0.0V 5 4.64V 13 0.34V 8 2.41V 2.41V 4.42V
(1.68V) 6 4.64V 14 1.67V 9 -- -- --
7 0.81V 15 0.00V 10 -- -- --
8 0.66V 16 0.97V 11 -- -- -- 17
Note:
18
MAIN Unit (Lot. 1~2)
Parts Layout (Side A)
A B C D E F
LC75834W NJM2070M FMW1 (W1) CPH6102 (AB) 2SC4154E (LE) RT1N441U (N3) MC2850 (A7) 12-22SURSYGC/S530-A2/TR8
(Q1054) (Q1039) (Q1032) (Q1051) (Q1025, 1038 (Q1042, 1053) (D1030) (D1026)
1050, 1061)
NJM12903R NJM2902V IMZ2 (Z2) RT1P441U (P3) 2SA1586Y (SY) DTC124TE (05) FA1101F (VX-180)
(Q1049) (Q1017, 1030) (Q1057) (Q1060) (Q1011, 1043) (Q1058) (D1035, 1038)
19
Parts Layout (Side B)
a b c d e f
M37516E6HP TA31136FN M62364FP 2SK2596 (BX) RT1N441U (N3) FMW1 (W1) DTB123EK (F12) S-80735SN (DZ) 2SC4154E (LE) DAN235E (M)
(Q1014) (Q1037) (Q1052) (Q1016) (Q1034, 1045 (Q1027, 1028) (Q1036) (Q1041) (Q1008, 1055) (D1016)
1063) 2SC5005 (73)
(Q1007)
2SC5006 (24)
(Q1012)
2SC4215Y (QY)
(Q1033)
2SC5227 (LN)
(Q1015)
2SC5231 (C8)
(Q1002)
MB15A02PFV1 BR93LC66FV 2SK2974 TK11250BMCL SGM2016AM (MA) RT1P441U (P3) 2SA1586Y (SY) CPH6102 (AB) MC2850 (A7)
(Q1005) (Q1010) (Q1024) (Q1040) (Q1026) (Q1013, 1020 (Q1056, 1062) (Q1029, 1031) (D1015, 1031,
1059) 1032, 1034)
20
21
Note:
22
A B C D E F
(Q1054) (Q1039) (Q1032) (Q1051) (Q1025, 1038 (Q1042, 1053) (D1030) (D1026)
1050, 1061)
(Q1049) (Q1017, 1030) (Q1057) (Q1060) (Q1011, 1043) (Q1058) (D1035, 1038)
23
a b c d e f
M37516M6 TA31136FN M62364FP 2SK2596 (BX) RT1N441U (N3) FMW1 (W1) DTB123EK (F12) S-80735SN (DZ) 2SC4154E (LE) DAN235E (M)
(Q1014) (Q1037) (Q1052) (Q1016) (Q1034, 1045 (Q1027, 1028) (Q1036) (Q1041) (Q1008, 1055) (D1016)
1063) 2SC5005 (73)
(Q1007)
2SC5006 (24)
(Q1012)
2SC4215Y (QY)
(Q1033)
2SC5227 (LN)
(Q1015)
2SC5231 (C8)
(Q1002)
(Q1005) (Q1010) (Q1024) (Q1040) (Q1026) (Q1013, 1020 (Q1056, 1062) (Q1029, 1031) (D1015, 1031,
1059) 1032, 1034)
24
25
Note:
26
A B C D E F
(Q1054) (Q1039) (Q1032) (Q1051) (Q1025, 1038 (Q1042, 1053) (D1030) (D1026)
1050, 1061)
(Q1049) (Q1017, 1030) (Q1057) (Q1060) (Q1011, 1043) (Q1058) (D1035, 1038)
27
a b c d e f
M37516M6 TA31136FN M62364FP 2SK2596 (BX) RT1N441U (N3) FMW1 (W1) DTB123EK (F12) S-80735SN (DZ) 2SC4154E (LE) DAN235E (M)
(Q1014) (Q1037) (Q1052) (Q1016) (Q1034, 1045 (Q1027, 1028) (Q1036) (Q1041) (Q1008, 1055) (D1016)
1063) 2SC5005 (73)
(Q1007)
2SC5006 (24)
(Q1012)
2SC4215Y (QY)
(Q1033)
2SC5227 (LN)
(Q1015)
2SC5231 (C8)
(Q1002)
(Q1005) (Q1010) (Q1024) (Q1040) (Q1026) (Q1013, 1020 (Q1056, 1062) (Q1029, 1031) (D1015, 1031,
1059) 1032, 1034)
28
29
Note:
30
A B C D E F
(Q1054) (Q1039) (Q1032) (Q1051) (Q1025, 1038 (Q1042, 1053) (D1030) (D1026)
1050, 1061)
(Q1049) (Q1017, 1030) (Q1057) (Q1060) (Q1011, 1043) (Q1058) (D1035, 1038)
31
a b c d e f
M37516M6 TA31136FN M62364FP 2SK2596 (BX) RT1N441U (N3) FMW1 (W1) DTB123EK (F12) S-80735SN (DZ) S-80835CNMC 2SC4154E (LE) DAN235E (M)
(Q1014) (Q1037) (Q1052) (Q1016) (Q1034, 1045 (Q1027, 1028) (Q1036) (Lot. 1-27) (Lot. 28-) (Q1008, 1055) (D1016)
1063) (Q1041) (Q1041) 2SC5005 (73)
(Q1007)
2SC5006 (24)
(Q1012)
2SC4215Y (QY)
(Q1033)
2SC5227 (LN)
(Q1015)
2SC5231 (C8)
(Q1002)
MB15A02PFV1 BR93L66FV 2SK2974 (Lot. 1-53) TK11250BMCL (Lot. 1-33) SGM2016AM (MA) RT1P441U (P3) 2SA1586Y (SY) CPH6102 (AB) MC2850 (A7)
(Q1005) (Q1010) RD07MVS1 (Lot. 54-) TK11250CMCL (Lot. 34-) (Q1026) (Q1013, 1020 (Q1056, 1062) (Q1029, 1031) (D1015, 1031,
(Q1024) (Q1040) 1059) 1032, 1034)
32
33
Note
34
Parts Layout
A B C D E F
Side A
(Q1054) (Q1039) (Q1032) (Q1051) (Q1025, 1038 (Q1042, 1053) (D1030) (D1026)
1050, 1061)
NJM12903R NJM2902V IMZ2 (Z2) RT1P441U (P3) 2SA1586Y (SY) PDTC114TE (24) FA1101F (VX-180)
(Q1049) (Q1017, 1030) (Q1057) (Q1060) (Q1011, 1043) (Q1058) (D1035, 1038)
35
a b c d e f
Side B
M37516E6HP TA31136FN M62364FP 2SK2596 (BX) RT1N441U (N3) FMW1 (W1) DTB123EK (F12) 2SC4154E (LE) S-80735SN (DZ) DAN235E (M)
(Q1014) (Q1037) (Q1052) (Q1016) (Q1034, 1045 (Q1027, 1028) (Q1036) (Q1008, 1055) (Q1041) (D1014)
1063) 2SC5005 (73)
(Q1007)
2SC5006 (24)
(Q1012)
2SC4215Y (QY)
(Q1033)
2SC5227 (LN)
(Q1015)
MB15A02PFV1 BR93LC66FV 2SK2974 TK11250BMCL 3SK299 RT1P441U (P3) 2SA1586Y (SY) CPH6102 (AB) MC2850 (A7)
(Q1005) (Q1010) (Q1024) (Q1040) (Q1026) (Q1013, 1020 (Q1056, 1062) (Q1029, 1031) (D1015, 1033
1059) 1034, 1036)
36
Circuit Diagram MAIN Unit (Lot. 109~)
37
Note
38
MAIN Unit (Lot. 109~)
Parts Layout
A B C D E F
Side A
(Q1054) (Q1039) (Q1032) (Q1051) (Q1025, 1038 (Q1042, 1053) (D1030) (D1026)
1050, 1061)
NJM12903R NJM2902V IMZ2 (Z2) RT1P441U (P3) 2SA1586Y (SY) PDTC114TE (24) FA1101F (VX-180)
(Q1049) (Q1017, 1030) (Q1057) (Q1060) (Q1011, 1043) (Q1058) (D1035, 1038)
39
MAIN Unit (Lot. 109~)
a b c d e f
Side B
M37516E6HP TA31136FN M62364FP 2SK2596 (BX) RT1N441U (N3) FMW1 (W1) DTB123EK (F12) 2SC4154E (LE) S-80735SN (DZ) DAN235E (M)
(Q1014) (Q1037) (Q1052) (Q1016) (Q1034, 1045 (Q1027, 1028) (Q1036) (Q1008, 1055) (Q1041) (D1014)
1063) 2SC5005 (73)
(Q1007)
2SC5006 (24)
(Q1012)
2SC4215Y (QY)
(Q1033)
2SC5227 (LN)
(Q1015)
MB15A02PFV1 BR93LC66FV 2SK2974 TK11250BMCL 3SK299 RT1P441U (P3) 2SA1586Y (SY) CPH6102 (AB) MC2850 (A7)
(Q1005) (Q1010) (Q1024) (Q1040) (Q1026) (Q1013, 1020 (Q1056, 1062) (Q1029, 1031) (D1015, 1033
1059) 1034, 1036)
40
MAIN Unit
Parts List
REF. DESCRIPTION VALUE V/W TOL. MFRS DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR
PCB with Components CB1390003 VX-160 (EXP):TYP CS1
CB1390004 VX-180 (EXP):TYP CS1
CB1390007 VX-160 (VTX):TYP C
CB1390008 VX-160 (EXP):TYP C
CB1390009 VX-160 (VTX):TYP A
CB1390010 VX-160 (EXP):TYP A
CB1390013 VX-180 (VTX):TYP C
CB1390014 VX-180 (EXP):TYP C
CB1390015 VX-180 (VTX):TYP A
CB1390016 VX-180 (EXP):TYP A
Printed Circuit Board FR006370E 1-2
FR006370G 3-17
FR006370H 18-27
FR006370I 28-99
FR006370K 100-108
FR006370L 109-
C 1001 CHIP CAP. 100pF 50V CH GRM1882C1H101JA01D K22174235 1-31 B b2
C 1001 CHIP CAP. 68pF 50V CH GRM1882C1H680JA01D K22174231 TYP A 45- B b2
C 1001 CHIP CAP. 150pF 50V CH GRM1882C1H151JA01D K22174239 TYP A 48 B b2
C 1001 CHIP CAP. 100pF 50V CH GRM1882C1H101JA01D K22174235 TYP C 32- B b2
C 1001 CHIP CAP. 68pF 50V CH GRM1882C1H680JA01D K22174231 TYP CS1 32- B b2
C 1002 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- B b2
C 1003 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 1- B b2
C 1004 CHIP CAP. 8pF 50V CH GRM1882C1H8R0DZ01D K22174209 1-44 B a1
C 1004 CHIP CAP. 12pF 50V CH GRM1882C1H120JA01D K22174213 TYP A 45- B a1
C 1004 CHIP CAP. 8pF 50V CH GRM1882C1H8R0DZ01D K22174209 TYP C 45- B a1
C 1004 CHIP CAP. 8pF 50V CH GRM1882C1H8R0DZ01D K22174209 TYP CS1 45- B a1
C 1005 CHIP CAP. 8pF 50V CH GRM1882C1H8R0DZ01D K22174209 1-38 B a1
C 1007 CHIP TA.CAP. 0.1uF 35V TESVA1V104M1-8R K78160025 1- B c2
C 1008 CHIP CAP. 22pF 50V CH GRM1882C1H220JA01D K22174219 1-44 B a1
C 1008 CHIP CAP. 27pF 50V CH GRM1882C1H270JA01D K22174221 TYP A 50-53 B a1
C 1008 CHIP CAP. 22pF 50V CH GRM1882C1H220JA01D K22174219 TYP C 45- B a1
C 1008 CHIP CAP. 22pF 50V CH GRM1882C1H220JA01D K22174219 TYP C 50-53 B a1
C 1008 CHIP CAP. 22pF 50V CH GRM1882C1H220JA01D K22174219 TYP CS1 45- B a1
C 1008 CHIP CAP. 22pF 50V CH GRM1882C1H220JA01D K22174219 TYP CS1 50-53 B a1
C 1008 CHIP CAP. 27pF 50V CH GRM1882C1H270JA01D K22174221 54- B a1
C 1009 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- B e2
C 1010 CHIP CAP. 5pF 50V CH GRM1882C1H5R0CZ01D K22174206 1-38 B a1
C 1010 CHIP CAP. 5pF 50V CH GRM1882C1H5R0CZ01D K22174206 TYP A 39- B a1
C 1010 CHIP CAP. 5pF 50V CH GRM1882C1H5R0CZ01D K22174206 TYP C 39- B a1
C 1011 CHIP TA.CAP. 0.1uF 35V TESVA1V104M1-8R K78160025 1- B c2
C 1012 CHIP CAP. 150pF 50V CH GRM1882C1H151JA01D K22174239 1- A A1
C 1015 CHIP CAP. 0.01uF 25V B GRM39B103K25PT K22144803 1- B e2
C 1016 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 1- B a1
C 1018 CHIP TA.CAP. 4.7uF 6.3V TEMSVA0J475M-8R K78080017 1- B c2
C 1019 CHIP CAP. 0.0033uF 50V B GRM188B11H332KA01D K22174831 1- A B1
C 1020 CHIP TA.CAP. 1uF 16V TESVA1C105M1-8R K78120009 1- B d2
C 1021 CHIP CAP. 22pF 50V CH GRM1552C1H220JZ01D K22178220 1- B c2
C 1021 CHIP CAP. 22pF 50V CH GRM1882C1H220JA01D K22174219 107- B c2
41
MAIN Unit
C 1022 CHIP TA.CAP. 0.1uF 35V TESVA1V104M1-8R K78160025 1- B d2
C 1023 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- B d1
C 1024 CHIP CAP. 27pF 50V CH GRM1882C1H270JA01D K22174221 50-53 B a1
C 1024 CHIP CAP. 33pF 50V CH GRM1882C1H330JA01D K22174223 TYP C 54- B a1
C 1024 CHIP CAP. 33pF 50V CH GRM1882C1H330JA01D K22174223 TYP CS1 54- B a1
C 1025 CHIP CAP. 2pF 50V CK GRM1884C1H2R0CZ01D K22174203 1-44 B c2
C 1025 CHIP CAP. 1pF 50V CK GRM1884C1H1R0CZ01D K22174202 TYP A 45- B c2
C 1025 CHIP CAP. 1pF 50V CK GRM1884C1H1R0BZ01D K22174267 TYP A 49-99 B c2
C 1025 CHIP CAP. 2pF 50V CK GRM1884C1H2R0CZ01D K22174203 TYP C 45-99 B c2
C 1025 CHIP CAP. 2pF 50V CK GRM1884C1H2R0CZ01D K22174203 TYP CS1 45-99 B c2
C 1025 CHIP CAP. 1pF 50V CK GRM1884C1H1R0BZ01D K22174267 100- B c2
C 1026 CHIP CAP. 120pF 50V CH GRM1882C1H121JA01D K22174237 1- B e2
C 1027 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 1- B c2
C 1029 CHIP CAP. 6pF 50V CH GRM1882C1H6R0DZ01D K22174207 1- B d2
C 1033 CHIP CAP. 18pF 50V CH K22174217 1- B c2
C 1034 CHIP CAP. 3pF 50V CJ GRM1883C1H3R0CZ01D K22174204 1- B c2
C 1034 CHIP CAP. 1pF 50V CK GRM1884C1H1R0CZ01D K22174202 28- B c2
C 1036 CHIP TA.CAP. 1uF 16V TESVA1C105M1-8R K78120009 1- B e2
C 1037 CHIP CAP. 680pF 25V CH GRM39CH681J25PT K22144203 1- A A2
C 1038 CHIP TA.CAP. 2.2uF 6.3V TESVA0J225M1-8R K78080009 1- B b2
C 1039 CHIP TA.CAP. 10uF 6.3V TEMSVA0J106M-8R K78080027 1- B d2
C 1040 CHIP CAP. 0.0047uF 50V B GRM188B11H472KA01D K22174833 1- B e2
C 1041 CHIP TA.CAP. 4.7uF 6.3V TEMSVA0J475M-8R K78080017 1- B b2
C 1042 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 1- A A1
C 1045 CHIP CAP. 100pF 50V CH GRM1882C1H101JA01D K22174235 1- B d1
C 1048 CHIP CAP. 18pF 50V CH K22174217 1- B c1
C 1049 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 1- B d1
C 1051 CHIP TA.CAP. 10uF 6.3V TEMSVA0J106M-8R K78080027 1- A A1
C 1054 CHIP TA.CAP. 10uF 6.3V TEMSVA0J106M-8R K78080027 1- B b2
C 1058 CHIP CAP. 5pF 50V CH GRM1882C1H5R0CZ01D K22174206 1- B c2
C 1058 CHIP CAP. 8pF 50V CH GRM1882C1H8R0DZ01D K22174209 28-31 B c2
C 1058 CHIP CAP. 8pF 50V CH GRM1882C1H8R0DZ01D K22174209 TYP A 45- B c2
C 1058 CHIP CAP. 8pF 50V CH GRM1882C1H8R0DZ01D K22174209 TYP C 32- B c2
C 1058 CHIP CAP. 22pF 50V CH GRM1882C1H220JA01D K22174219 TYP CS1 32- B c2
42
MAIN Unit
C 1075 CHIP CAP. 330pF 50V B GRM188B11H331KD01D K22174820 1- B d1
C 1077 CHIP CAP. 0.033uF 16V R GRM188R11C333KA01D K22124801 1- A B1
C 1079 CHIP CAP. 470pF 50V CH GRM1882C1H471JA01D K22174249 1- A B1
C 1080 CHIP CAP. 0.022uF 25V B GRM39B223K25PT K22144807 1- A B1
C 1089 CHIP CAP. 10pF 50V CH GRM1882C1H100JA01D K22174211 1- B b3
C 1099 CHIP TA.CAP. 10uF 16V TEMSVB21C106M-8R K78120025 1- A E1
C 1102 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 1- A E1
C 1108 CHIP CAP. 0.01uF 25V B GRM39B103K25PT K22144803 1- A E2
C 1110 CHIP CAP. 5pF 50V CH GRM1882C1H5R0CZ01D K22174206 1-44 B a1
C 1110 CHIP CAP. 8pF 50V CH GRM1882C1H8R0DZ01D K22174209 TYP A 45- B a1
C 1110 CHIP CAP. 7pF 50V CH GRM1882C1H7R0DZ01D K22174208 TYP C 54-99 B a1
C 1110 CHIP CAP. 5pF 50V CH GRM1882C1H5R0CZ01D K22174206 TYP CS1 45- B a1
C 1110 CHIP CAP. 5pF 50V CH GRM1882C1H5R0CZ01D K22174206 TYP CS1 50- B a1
C 1110 CHIP CAP. 7pF 50V CH GRM1882C1H7R0DZ01D K22174208 TYP CS1 54-99 B a1
C 1116 CHIP TA.CAP. 10uF 6.3V TEMSVA0J106M-8R K78080027 1- B e3
C 1117 CHIP TA.CAP. 4.7uF 6.3V TEMSVA0J475M-8R K78080017 1- A C1
C 1120 CHIP CAP. 0.01uF 25V B GRM39B103K25PT K22144803 1- A A3
C 1121 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- B d2
43
MAIN Unit
C 1124 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- A A3
C 1127 CHIP TA.CAP. 1uF 16V TESVA1C105M1-8R K78120009 1- A A2
C 1129 CHIP TA.CAP. 4.7uF 6.3V TEMSVA0J475M-8R K78080017 1- B e2
C 1138 CHIP TA.CAP. 10uF 6.3V TEMSVA0J106M-8R K78080027 1- A E2
C 1140 CHIP CAP. 2.2uF 10V B GRM42-6B225K10PT K22101801 18- B e1
C 1140 CHIP CAP. 2.2uF 10V B GRM188B31A225KE18D K22104805 100- B e1
C 1142 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- A E2
C 1143 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 1- B f2
C 1147 CHIP TA.CAP. 4.7uF 16V TEMSVA1C475M-8R K78120031 1- B f2
C 1149 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- A F2
C 1150 AL.ELECTRO.CAP. 220uF 10V ESMG100ELL221ME11S K40109027 1- B a2
C 1151 CHIP CAP. 220pF 50V CH GRM1882C1H221JA01D K22174243 1- A F2
C 1152 CHIP TA.CAP. 1uF 16V TESVA1C105M1-8R K78120009 1- A B2
C 1153 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- A B1
C 1156 CHIP CAP. 0.0022uF 50V B GRM188B11H222KA01D K22174822 1- A B2
C 1159 CHIP TA.CAP. 10uF 6.3V TEMSVA0J106M-8R K78080027 1- B d2
C 1165 CHIP CAP. 0.01uF 25V B GRM39B103K25PT K22144803 1- A E3
C 1166 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- A D1
C 1173 CHIP CAP. 7pF 50V CH GRM1882C1H7R0DZ01D K22174208 1- B b2
C 1176 CHIP TA.CAP. 2.2uF 6.3V TESVA0J225M1-8R K78080009 1- A D1
C 1179 CHIP CAP. 18pF 50V CH K22174217 TYP CS1 32- B b2
44
MAIN Unit
C 1180 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- B c2
C 1193 CHIP CAP. 0.01uF 25V B GRM39B103K25PT K22144803 1- A D1
C 1198 CHIP TA.CAP. 4.7uF 6.3V TEMSVA0J475M-8R K78080017 VX-180 1- B d1
C 1199 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 VX-180 1- B d1
C 1200 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 VX-180 1- A C1
C 1201 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 VX-180 1- A C1
C 1202 CHIP CAP. 680pF 50V B GRM188B11H681KA01D K22174807 VX-180 1- A C1
C 1204 CHIP TA.CAP. 4.7uF 6.3V TEMSVA0J475M-8R K78080017 VX-180 1- B d1
C 1210 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 1- A D3
C 1211 CHIP CAP. 220pF 50V CH GRM1882C1H221JA01D K22174243 1- A D3
C 1228 CHIP TA.CAP. 10uF 6.3V TEMSVA0J106M-8R K78080027 1- A E2
C 1231 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1-17 A A2
C 1232 CHIP TA.CAP. 0.1uF 35V TESVA1V104M1-8R K78160025 1- B d3
C 1235 CHIP CAP. 330pF 50V B GRM188B11H331KD01D K22174820 3- B c1
C 1235 CHIP CAP. 330pF 50V B GRM188B11H331KD01D K22174820 50-53 B c1
C 1236 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- A B1
C 1240 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 TYP CS1 61-
C 1240 CHIP CAP. 0.001uF 50V B GRM188B11H102KA01D K22174821 TYP CS1 100-
C 1241 CHIP CAP. 2pF 50V CK GRM1884C1H2R0CZ01D K22174203 TYP A 76-79 A E1
CD1001 CERAMIC DISC CDBCB450KCAY24-R0 H7901340 1- B d2
CF1001 CERAMIC FILTER ALFYM450G=K H3900534 1- A C3
CF1002 CERAMIC FILTER ALFYM450F=K H3900531 1- A C2
D 1002 DIODE HSU277TRF G2070118 1- B b1
D 1003 DIODE RLS135 TE-11 G2070128 1- B a1
D 1004 DIODE HVC350B-TRF G2070596 1- B d2
D 1005 DIODE 1SV229 TPH3 G2070256 1-44 B c2
D 1005 DIODE HVU358TRF G2070418 TYP A 45- B c2
D 1005 DIODE 1SV229 TPH3 G2070256 TYP A 100- B c2
D 1005 DIODE 1SV229 TPH3 G2070256 TYP C 45- B c2
D 1005 DIODE 1SV229 TPH3 G2070256 TYP CS1 45- B c2
D 1005 DIODE HVU358TRF G2070418 TYP CS1 54- B c2
D 1006 DIODE HSU277TRF G2070118 1- B a1
D 1008 DIODE HSU277TRF G2070118 1- B a2
D 1010 DIODE 1SS355 TE-17 G2070470 1- B b1
D 1011 DIODE HVC358B(TAPE) G2070590 1- B a2
45
MAIN Unit
D 1015 DIODE MC2850-T11-1 G2070704 1- B f1
D 1016 DIODE DAN235E TL G2070612 1- B c2
D 1017 DIODE HVC358B(TAPE) G2070590 1-60 B a3
D 1017 DIODE HVC358B(TAPE) G2070590 TYP A 61- B a3
D 1017 DIODE HVC358B(TAPE) G2070590 TYP C 61- B a3
D 1019 DIODE HVC358B(TAPE) G2070590 1- B b3
D 1021 DIODE 1SS355 TE-17 G2070470 1- B e1
D 1022 DIODE 1SS355 TE-17 G2070470 1- B e1
D 1023 DIODE 1SS355 TE-17 G2070470 1- B e1
D 1024 DIODE 1SS355 TE-17 G2070470 1- B e1
D 1026 LED 12-22SURSYGC/S530-A2/TR8 G2070810 1- A F1
D 1028 DIODE 1SS355 TE-17 G2070470 1- B e2
D 1028 DIODE 1SS355 TE-17 G2070470 54- B e2
D 1030 DIODE MC2850-T11-1 G2070704 1- A A2
D 1031 DIODE MC2850-T11-1 G2070704 1- B c3
D 1032 DIODE MC2850-T11-1 G2070704 1- B c3
D 1034 DIODE MC2850-T11-1 G2070704 1- B c2
D 1035 LED FA1101F-TR G2070842 VX-180 1- A C3
D 1036 DIODE 1SS355 TE-17 G2070470 1- B e2
D 1037 DIODE HVC358B(TAPE) G2070590 1-31 B b2
D 1037 DIODE HVC358B(TAPE) G2070590 TYP A 45- B b2
D 1037 DIODE HVC358B(TAPE) G2070590 TYP C 32- B b2
D 1037 DIODE 1SV305(TPH3) G2070942 TYP CS1 32- B b2
D 1038 LED FA1101F-TR G2070842 VX-180 1- A C1
D 1040 DIODE 1SS355 TE-17 G2070470 VX-180 1- B c1
D 1041 DIODE 1SS355 TE-17 G2070470 1- B a2
D 1041 DIODE 1SS400 TE61 G2070634 3- B a2
D 1042 DIODE HVU355TRF G2070410 1- B b2
D 1042 DIODE HVC355B(TAPE) G2070588 3-31 B b2
D 1042 DIODE HVC355B(TAPE) G2070588 TYP A 45- B b2
D 1042 DIODE HVC355B(TAPE) G2070588 TYP C 32- B b2
D 1042 DIODE 1SV305(TPH3) G2070942 TYP CS1 32- B b2
D 1043 SURGE ABSORBER TVSF0805 Q9000807 100- A F1
D 1043 SURGE ABSORBER TVSF0603 Q9000847 109- A F1
DS1001 LCD HT-3633-TFZWH G6090139 VX-180 1- A C2
HS1001 HEATSINK PLATE 135t RA0724500 100- B b1
HS1001 HEATSINK PLATE 135t RA072450A 103- B b1
J 1001 SPRING CONECTOR MS0062-10 S5000227 1- B a1
J 1003 CONNECTOR HSJ1594-010055 P1090896 1- B b3
J 1004 SHIELD FINGER 3525 3100103 S5000226 1- A D2
J 1005 SHIELD FINGER 3525 3100103 S5000226 1- A D2
L 1001 COIL E2 0.5-2.0-6T-R L0022488 1- B a1
L 1002 COIL E2 0.5-2.0-6T-R L0022488 1- B a1
L 1003 M.RFC 0.056uH C2012C-56NK L1690673 1- B b2
L 1003 M.RFC 0.056uH 2% C2012C-56NG L1690773 3-38 B b2
L 1003 M.RFC 0.056uH 2% C2012C-56NG L1690773 TYP A 39- B b2
L 1003 M.RFC 0.056uH 2% C2012C-56NG L1690773 TYP C 39- B b2
L 1003 M.RFC 0.068uH 2% C2012C-68NG L1690774 TYP CS1 39- B b2
L 1003 M.RFC 0.047uH 2% C2012C-47NG L1690772 TYP CS1 54- B b2
L 1004 COIL E2 0.35-1.6-7T-L L0022390 1-38 B b2
L 1004 COIL E2 0.3-1.7-7T-R L0022372 TYP A 39- B b2
L 1004 COIL E2 0.35-1.6-7T-L L0022390 TYP C 39- B b2
L 1004 COIL E2 0.35-1.6-5.5T-L L0022616 TYP CS1 39- B b2
L 1004 COIL E2 0.35-1.6-7T-L L0022390 TYP CS1 54- B b2
L 1007 COIL E2 0.3-1.7-8T-L L0022376 1- B a1
L 1008 COIL E2 0.3-1.7-8T-L L0022376 1- B a1
L 1009 M.RFC 0.1uH HK1608 R10J-T L1690528 1- B c1
L 1010 COIL E2 0.3-1.7-7T-R L0022372 1-44 B a2
46
MAIN Unit
L 1010 COIL E2 0.3-1.7-8T-L L0022376 TYP A 45- B a2
L 1010 COIL E2 0.3-1.7-7T-R L0022372 TYP C 45- B a2
L 1010 COIL E2 0.3-1.7-7T-R L0022372 TYP CS1 45- B a2
L 1011 COIL E2 0.3-1.7-7T-R L0022372 1-44 B a2
L 1012 M.RFC 0.068uH HK1608 68NJ-T L1690526 28- B c2
L 1013 M.RFC 0.047uH HK1608 47NJ-T L1690524 1-60 B a2
L 1013 M.RFC 0.047uH HK1608 47NJ-T L1690524 TYP A 61- B a2
L 1013 M.RFC 0.047uH HK1608 47NJ-T L1690524 TYP C 61- B a2
L 1014 M.RFC 0.1uH HK1608 R10J-T L1690528 1- B a2
L 1017 COIL E2 0.3-1.7-7T-R L0022372 1-44 B a3
L 1018 COIL E2 0.35-1.6-7T-L L0022390 1- A D1
L 1020 M.RFC 0.022uH HK2125 22NK-T L1690381 1-43 B b1
L 1020 M.RFC 0.022uH HK2125 22NK-T L1690381 TYP A 44- B b1
L 1020 M.RFC 0.022uH HK2125 22NK-T L1690381 TYP A 50-53 B b1
L 1020 M.RFC 0.022uH HK2125 22NK-T L1690381 TYP C 44- B b1
L 1020 M.RFC 0.022uH HK2125 22NK-T L1690381 TYP C 50-53 B b1
L 1020 M.RFC 0.018uH HK2125 18NK-T L1690380 TYP CS1 44- B b1
L 1020 M.RFC 0.018uH HK2125 18NK-T L1690380 TYP CS1 50-53 B b1
L 1020 M.RFC 0.022uH HK2125 22NK-T L1690381 54- B b1
L 1021 COIL E2 0.3-1.7-7T-R L0022372 1-44 B b3
L 1021 COIL E2 0.3-1.7-8T-L L0022376 TYP A 45- B b3
L 1021 COIL E2 0.3-1.7-7T-R L0022372 TYP C 45- B b3
L 1021 COIL E2 0.3-1.7-7T-R L0022372 TYP CS1 45- B b3
L 1022 COIL E2 0.45-1.4-4T-L L0022391 1- A E1
L 1022 COIL E2 0.45-1.4-4T-L L0022391 50- A E1
L 1022 COIL E2 0.35-1.6-7T-L L0022390 54- A E1
L 1023 M.RFC 0.082uH HK1608 82NJ-T L1690527 1-44 B b2
L 1023 M.RFC 0.1uH HK1608 R10J-T L1690528 TYP A 45- B b2
L 1023 M.RFC 0.082uH HK1608 82NJ-T L1690527 TYP C 45- B b2
L 1023 M.RFC 0.082uH HK1608 82NJ-T L1690527 TYP CS1 45- B b2
L 1024 COIL E2 0.5-1.4-2.5T-L L0022613 1- B b1
L 1025 COIL E2 0.5-2.0-5T-R L0022487 1- B b1
L 1026 M.RFC 0.82uH LK1608 R82K-T L1690417 1- B b2
L 1027 M.RFC 0.82uH LK2125 R82K-T L1690318 1- B a1
L 1029 M.RFC 0.82uH LK1608 R82K-T L1690417 1- B c2
L 1030 M.RFC 3.3uH LK1608 3R3K-T L1690686 1- B b2
L 1032 M.RFC 0.022uH HK1608 22NJ-T L1690520 1-43 B b1
L 1032 M.RFC 0.022uH HK1608 22NJ-T L1690520 TYP A 44- B b1
L 1032 M.RFC 0.022uH HK1608 22NJ-T L1690520 TYP A 50-53 B b1
L 1032 M.RFC 0.022uH HK1608 22NJ-T L1690520 TYP C 44- B b1
L 1032 M.RFC 0.022uH HK1608 22NJ-T L1690520 TYP C 50-53 B b1
L 1032 M.RFC 0.047uH HK1608 47NJ-T L1690524 TYP CS1 44- B b1
L 1032 M.RFC 0.047uH HK1608 47NJ-T L1690524 TYP CS1 50-53 B b1
L 1032 M.RFC 0.22uH HK1608 R22J-T L1690940 54- B b1
L 1034 M.RFC 0.068uH LK1608 68NM-T L1690406 1- B c1
L 1034 M.RFC 0.068uH LK1608 68NM-T L1690406 50-53 B c1
MC1001 MIC. ELEMENT EM-100PT M3290029 1- A D1
Q 1002 TRANSISTOR 2SC5231C8-TL G3352318H 1- B c2
Q 1005 IC MB15A02PFV1-G-BND-EF G1092541 1- B d1
Q 1007 TRANSISTOR 2SC5005-T1 G3350058 1- B c2
Q 1008 TRANSISTOR 2SC4154-T11-1E G3341548E 1- B b2
Q 1010 IC BR93LC66FV-E2 G1092853 1- B e2
Q 1010 IC BR93L66FV-WE2 G1093910 38- B e2
47
MAIN Unit
Q 1011 TRANSISTOR 2SA1586Y TE85R G3115867Y 1- A A1
Q 1012 TRANSISTOR 2SC5006-T1 G3350068 1- B a2
Q 1013 TRANSISTOR RT1P441U-T11-1 G3070248 1- B f1
Q 1014 IC M37516E6HP(NO PROG.) 1- B e1
Q 1014 IC M37516M6-121HP 5- B e1
Q 1014 IC M37516M6-146HP 28- B e1
Q 1014 IC M37516M6-182HP 70- B e1
Q 1015 TRANSISTOR 2SC5227-4-TB G3352278D 1- B c1
Q 1016 FET 2SK2596BXTL G3825967 1- B c1
Q 1017 IC NJM2902V-TE1 G1091679 1- A A1
Q 1020 TRANSISTOR RT1P441U-T11-1 G3070248 1- B e1
Q 1024 FET 2SK2974-T11 G3829747 1- A D1
Q 1024 FET 2SK2974-T11 G3829747 50- A D1
Q 1024 FET RD07MVS1-T12 G3070320 54- A D1
Q 1024 FET RD07MVS1-T12(A) G3070320A 102 A D1
Q 1024 FET RD07MVS1A-T12 G3070352 103- A D1
Q 1025 TRANSISTOR 2SC4154-T11-1E G3341548E 1- A F1
Q 1026 FET SGM2016AM-T7 G4070012 1- B b2
Q 1026 FET 3SK299-T1(U73) G4802998 109- B b2
Q 1027 TRANSISTOR FMW1 T98 G3070009 1- B e3
Q 1028 TRANSISTOR FMW1 T98 G3070009 1- B f3
Q 1029 TRANSISTOR CPH6102-TL G3070223 1- B e3
Q 1030 IC NJM2902V-TE1 G1091679 1- A A2
Q 1031 TRANSISTOR CPH6102-TL G3070223 1- B f2
Q 1032 TRANSISTOR FMW1 T98 G3070009 1- A E2
Q 1033 TRANSISTOR 2SC4215Y TE85R G3342157Y 1- B c2
Q 1034 TRANSISTOR RT1N441U-T11-1 G3070247 1- B e2
Q 1036 TRANSISTOR DTB123EK T146 G3070022 1- B e3
Q 1037 IC TA31136FN(EL) G1091605 1- B d2
Q 1038 TRANSISTOR 2SC4154-T11-1E G3341548E 1- A E2
Q 1039 IC NJM2070M-TE2 G1092944 1- A E2
Q 1040 IC TK11250BMCL G1092952 1- B f2
Q 1040 IC TK11250CMCL-G G1093694 34- B f2
Q 1041 IC S-80735SN-DZ-T1 G1091876 1- B e2
Q 1041 IC S-80835CNMC-B8U-T2-G G1093606 28- B e2
Q 1042 TRANSISTOR RT1N441U-T11-1 G3070247 1- A A2
Q 1043 TRANSISTOR 2SA1586Y TE85R G3115867Y 1- A A2
Q 1045 TRANSISTOR RT1N441U-T11-1 G3070247 1- B d2
Q 1049 IC NJM12903R-TE1 G1093336 1- A A2
Q 1050 TRANSISTOR 2SC4154-T11-1E G3341548E 1- A A3
Q 1051 TRANSISTOR CPH6102-TL G3070223 1- A E2
Q 1052 IC M62364FP 600D G1093033 1- B e3
Q 1053 TRANSISTOR RT1N441U-T11-1 G3070247 1- A C1
Q 1054 IC LC75834W G1093288 VX-180 1- A C2
Q 1055 TRANSISTOR 2SC4154-T11-1E G3341548E 1- B e2
Q 1056 TRANSISTOR 2SA1586Y TE85R G3115867Y 1- B d1
Q 1057 TRANSISTOR IMZ2A T108 G3070060 1- A E1
Q 1058 TRANSISTOR DTC124TE TL G3070128 VX-180 1- A C1
Q 1059 TRANSISTOR RT1P441U-T11-1 G3070248 1- B b2
Q 1060 TRANSISTOR RT1P441U-T11-1 G3070248 1- A E2
Q 1061 TRANSISTOR 2SC4154-T11-1E G3341548E VX-180 1- A C1
Q 1062 TRANSISTOR 2SA1586Y TE85R G3115867Y 1- B c1
Q 1063 TRANSISTOR RT1N441U-T11-1 G3070247 1- B c1
R 1001 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- B b2
R 1002 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1-44 B d2
R 1002 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 TYP A 45- B d2
R 1002 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 TYP C 45- B d2
R 1002 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 TYP CS1 45- B d2
R 1002 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 TYP CS1 100 B d2
R 1003 CHIP RES. 56k 1/16W 5% RMC1/16 563JATP J24185563 1-44 B d2
R 1003 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 TYP A 45- B d2
: Please contact VERTEX STANDARD
48
MAIN Unit
R 1003 CHIP RES. 560k 1/16W 5% RMC1/16 564JATP J24185564 TYP CS1 100 B d2
R 1004 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 1- B c2
R 1005 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1-53 B c1
R 1005 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 TYP A 54- B c1
R 1005 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 TYP C 54- B c1
R 1005 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 TYP CS1 54- B c1
R 1006 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B b1
R 1007 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 1- B d2
R 1008 CHIP RES. 82k 1/16W 5% RMC1/16 823JATP J24185823 1- A A1
R 1009 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- B d3
R 1011 CHIP RES. 1.2k 1/16W 5% RMC1/16 122JATP J24185122 1-31 B d2
R 1011 CHIP RES. 1.2k 1/16W 5% RMC1/16 122JATP J24185122 TYP A 45- B d2
R 1011 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 TYP A 100- B d2
R 1011 CHIP RES. 1.2k 1/16W 5% RMC1/16 122JATP J24185122 TYP C 32- B d2
R 1011 CHIP RES. 680 1/16W 5% RMC1/16 681JATP J24185681 TYP CS1 100- B d2
R 1014 CHIP RES. 820 1/16W 5% RMC1/16 821JATP J24185821 1- B c2
R 1016 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- B c2
R 1023 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- B d2
R 1026 CHIP RES. 68k 1/16W 5% RMC1/16 683JATP J24185683 1- B e2
R 1028 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1-17 A A2
R 1031 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- B e2
R 1033 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- B b2
R 1034 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- A C1
R 1041 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- B a2
R 1043 CHIP RES. 1.2M 1/16W 5% RMC1/16 125JATP J24185125 1- A A1
R 1048 CHIP RES. 1.8M 1/16W 5% RMC1/16 185JATP J24185185 1- A A2
R 1049 CHIP RES. 1.8k 1/16W 5% RMC1/16 182JATP J24185182 1- A A1
R 1051 CHIP RES. 10k 1/16W 1% RMC1/16 103FTP J24183103 1- A A1
49
MAIN Unit
R 1061 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f2
R 1064 CHIP RES. 330k 1/16W 1% RMC1/16 334FTP J24183334 1- B e2
R 1065 CHIP RES. 82k 1/16W 1% RMC1/16 823FTP J24183823 1- B e1
R 1068 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1-31 B a2
R 1068 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 TYP A 45- B a2
R 1068 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 TYP C 32- B a2
R 1068 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 TYP CS1 32- B a2
R 1069 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 3-43 B d1
R 1069 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP A 44- B d1
R 1069 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP A 50-53 B d1
R 1069 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP C 44- B d1
R 1069 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP C 50-53 B d1
R 1069 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 TYP CS1 44- B d1
R 1069 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 TYP CS1 50-53 B d1
R 1070 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- B f1
R 1071 CHIP RES. 1.5M 1/16W 5% RMC1/16 155JATP J24185155 1- A B1
R 1073 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- B f1
R 1074 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- B a2
R 1075 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B a2
R 1078 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 TYP A 50-53 B d1
R 1078 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 TYP C 50-53 B d1
R 1078 CHIP RES. 15 1/16W 5% RMC1/16 150JATP J24185150 TYP CS1 50-53 B d1
R 1079 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A B1
R 1089 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1-44 B c1
R 1089 CHIP RES. 56 1/16W 5% RMC1/16 560JATP J24185560 TYP A 45-53 B c1
R 1089 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 TYP C 45-53 B c1
R 1089 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 TYP CS1 45-53 B c1
R 1089 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 TYP A 76- B c1
R 1089 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 TYP C 76- B c1
R 1089 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 TYP CS1 76- B c1
50
MAIN Unit
R 1093 CHIP RES. 22 1/2W 5% RMC1/2 220JCTP J24275220 1- A D1
R 1094 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B f2
R 1100 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- A F1
R 1105 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- A F2
R 1106 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1-27 B b2
R 1107 CHIP RES. 220 1W 5% RMC1 221JTE J24305221 1- A E1
R 1108 CHIP RES. 0.33 1/8W 10% RMC1/8 R33KTP J24219001 1- A E1
R 1113 CHIP RES. 27k 1/16W 5% RMC1/16 273JATP J24185273 1- A E1
R 1113 CHIP RES. 5.6k 1/16W 5% RMC1/16 562JATP J24185562 54- A E1
R 1114 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 54- A E1
R 1116 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 1- B e3
R 1118 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- A E1
R 1124 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP A 45- B c2
R 1124 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP C 32- B c2
R 1124 CHIP RES. 390 1/16W 5% RMC1/16 391JATP J24185391 TYP CS1 32- B c2
R 1133 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- A C1
R 1141 CHIP RES. 470 1/10W 5% RMC1/10T 471J J24205471 1- A E2
R 1149 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 1-101 A A2
51
MAIN Unit
R 1149 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 EXP 102- A A2
R 1149 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 VTX 102- A A2
R 1162 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- A F2
R 1166 CHIP RES. 2.2 1/16W 5% RMC1/16 2R2JATP J24185229 1- A F2
R 1168 CHIP RES. 470k 1/16W 1% RMC1/16 474FTP J24183474 1-70 A A2
R 1168 CHIP RES. 470k 1/16W 1% RMC1/16 474FTP J24183474 TYP A 71-74 A A2
R 1168 CHIP RES. 470k 1/16W 1% RMC1/16 474FTP J24183474 TYP C 71-74 A A2
R 1168 CHIP RES. 330k 1/16W 1% RMC1/16 334FTP J24183334 TYP CS1 71-74 A A2
R 1171 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A B1
R 1172 CHIP RES. 22k 1/16W 1% RMC1/16 223FTP J24183223 1- A B2
R 1176 CHIP RES. 10k 1/16W 1% RMC1/16 103FTP J24183103 1- A B2
R 1190 CHIP RES. 470 1/16W 1% RMC1/16 471FTP J24183471 1- A A2
R 1190 CHIP RES. 560 1/16W 1% RMC1/16 561FTP J24183561 18- A A2
R 1207 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 VX-180 1- A C1
52
MAIN Unit
R 1208 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1-31 A D2
R 1208 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP A 45- A D2
R 1208 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP C 32- A D2
R 1209 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 VX-180 1- B d1
R 1210 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 VX-180 1- B d1
R 1215 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 VX-180 1- B c1
R 1223 CHIP RES. 390 1/16W 5% RMC1/16 391JATP J24185391 VX-180 1- A C3
R 1236 CHIP RES. 2.2M 1/16W 5% RMC1/16 225JATP J24185225 1- A B2
R 1242 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- A D3
R 1247 CHIP RES. 0 1/10W 5% RMC1/10T 000J J24205000 1- A E1
R 1253 CHIP RES. 390 1/16W 5% RMC1/16 391JATP J24185391 VX-180 1- A C1
R 1258 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- A B2
R 1263 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 18- A A2
R 1264 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP CS1 61-
R 1264 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 TYP CS1 100-
S 1001 ROTARY SWITCH EC10SP16-85A0 Q9000764 1- B a2
S 1002 TACT SWITCH SKHLLD N5090066 1- B b1
S 1003 TACT SWITCH SKHLLD N5090066 1- B c1
TH1004 THERMISTOR TBPS1R103K440H5Q G9090067 1- B d1
VR1006 POT. RK0971111 20KA/SW J60800256 1- B a3
X 1001 XTAL SX-2112 14.6MHz 14.6MHZ H0103237 1- B d2
X 1001 XTAL SX-2112 14.6MHz 14.6MHZ H0103260 3- B d2
X 1002 XTAL SX-1319 3.6864MHz 3.6864MHZ H0103214 1- B e1
53
MAIN Unit
X 1002 XTAL U3B 3.6864MHz 3.686400MHz (11p) H0103307 76- B e1
XF1001 XTAL FILTER HDF0051 44.25M H1102358 TYP CS1 32- B b2
XF1002 XTAL FILTER HDF0042 44.25MHZ H1102346 1-31 B b2
XF1002 XTAL FILTER HDF0042 44.25MHZ H1102346 TYP A 45- B b2
XF1002 XTAL FILTER HDF0042 44.25MHZ H1102346 TYP C 32- B b2
XF1002 XTAL FILTER HDF0051 44.25M H1102358 TYP CS1 32- B b2
INTER CONNECTOR RA0294800 VX-180 1-
LCD HOLDER RA0294400 VX-180 1-
LIGHT GUIDE (LCD) RA0294500 VX-180 1-
LIGHT GUIDE (LCD) RA029450A VX-180 10-
LIGHT GUIDE (LCD) RA029450B VX-180 76-
TERMINAL HOLDER RA010340A 1-
TERMINAL HOLDER RA010340B 28-
TERMINAL PLATE (+) RA0351700 1-
HOLDER RUBBER (MIC) RA0110200 1-
REFLECTOR SHEET RA033490A VX-180 1-
54
Copyright 2004
VERTEX STANDARD CO., LTD.
All rights reserved
No portion of this manual
may be reproduced without
the permission of
VERTEX STANDARD CO., LTD. E C 0 1 3 N 9 0 B
18

VX-160V 180V

Uploaded by

Copyright:

Available Formats

VX-160V 180V

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

VX-160V 180V

Uploaded by

Copyright:

Available Formats

VERTEX STANDARD CO., LTD.

4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan

Accessories & Options

Optional Cloning Cable CT-27

RECEIVER Specifications (Measurements made per EIA standard TIA/EIA-603)

TRANSMITTER Specifications (Measurements made per EIA standard TIA/EIA-603)

RA029430A (Lot. 4~)

Transmitter Output Power IN

SQL Open:0.73V SQL Open:0.0V

LED On:2.77V 1.56V

SQL Open:0.59V SQL Close:0.9V

SQL Open: 5.0V 0.0V

0.0V <5.07V> SQL Open:0.26V SQL Close:7.5V

You might also like