3120036/3 IM-S13-12

CH Issue 3

SV5 Safety Valve

Installation and Maintenance Instructions

1. General specification

2. Supply
3. Before fitting the valve
4. Installation

5. Damage prevention
6. Commissioning
7. Testing during use

8. Guidelines for setting

9. Maintenance

Printed in theCH
IM-S13-12 UKIssue 3 Copyright 1997
1
 1. General specification
To safe
area

Safety valve
Reducing valve

Steam
supply Condensate

Fig. 1 Typical installation of safety valve, downstream of a steam pressure reducing valve station

Description Sizes and pipe connections

The SV5 is a range of full lift flanged safety Inlet sizes include DN 20, 25, 32, 40, 50, 65,
valves suitable for use on steam, gas and 80, 100, 125 & 150
liquid service.
Valve Type Inlet Outlet
Available types connection connection
Two main variations of the valve are available,
the SV 57 and SV 54, in SG Iron and Carbon SV 57 PN 25 PN 16
Steel body materials respectively. Inlet sizes SV 54 PN 40 PN 16
range from DN20 to DN150, each with an SV 54 ANSI300 ANSI150
option of easing lever, "O" ring soft seal and
open and closed bonnets. Limiting Conditions
DIN or ANSI flange options available.
Valve Inlet
Standards and approvals Type flange Pressure Temperature
Approved by SAFed - TAS (British Engine) to SV 57 PN 25 25 bar max. -10C to +300C
BS6759 parts 1 and 2 and the TUV to AD
Merkblatt A2 TRD421 SV 54 PN40/ 40 bar max. -10C to +400C
Seat tightness to API 527 ANSI 300

"O" Ring Soft seal Material:

PTFE - 10C to + 205C.
Viton - 10C to + 180C.
Buna-N - 10C to + 90C max.

2 IM-S13-12 CH Issue 3
Dimensions (All dimensions in mm)
Size DN A B C Weight kg
20 85 95 315 10
25 100 105 325 11.5
32 110 115 362 15
40 115 140 362 17
50 120 150 402 20 C
65 140 170 520 37.5
80 160 195 560 50
100 180 220 665 77
125 200 250 792 115
150 225 285 880 180

Installation and service

The Safety Valve should always be fitted with
the centre line of the spring housing vertically
above the valve. See full installation
instructions on page 6.
Open bonnet valves are recommended where
the media temperature exceeds 250C.
A comprehensive valve refurbishment service
is available upon request.
How to specify
Body Material Valve Size
4 = CS 1 = 20x32 2 = 25x40 3 = 32x50 4 = 40x65 5 = 50x80
7 = SGI 6 = 65x100 7= 80x125 8 = 100x150 9 = 125x200 10 = 150x250

Flange Bonnet Configuration

1 = PN 1 = Open 1 = Gas tight cap
2 = ANSI* 2 = Closed 2 = Easing Lever
3 = Packed Easing lever

Seal Material
1 = St. Steel
2 = PTFE
3 = Viton
4 = Buna-N

SV5 4 1 1 2 2 1
Example: 1 - Spirax Sarco SV54-1-1221 safety valve set to 6 bar.
* SV54 - Steel valves only

IM-S13-12 CH Issue 3 3
Materials of construction
Item Component Material - SV 57 / SV54 34 30 29 28 27
1 Body GGG-40.3/GSC-25
2 Seat 1.4057
3 Bonnet GGG-40.3/GS-C25
4 Cap GGG-40.3
5 Disc Hardened 1.4021
6 Disc guide GGG-40.3
7 Skirt 1.4031
8 Spindle 1.4034
9 Body Bolts
DIN-931 5.6 ZN/DIN-933 CK-35
10 Spring washers CK 45 Packed easing lever
11 Retainer ring 1.4034
12 Guide sleeve 1.4031
13 Spring adjustment screw 1.4034
14 Lock nut
Carbon steel DIN 1651 9S Mn 36 Zp
15 SpringCarbon Steel DIN 17225 50 crV4
16 Cap bolt DIN-931 5.6 ZN
17 Collar Carbon steel, Zinc plated
18 Lever GGG 40.3
19 Pin Carbon steel, Zinc plated
20 Circlip DIN-471 Carbon steel
Gas tight cap
21 Pin DIN-7343
22 Drain Hole " BSP
23 Spindle Ball 1.4034
24 Identification plate Stainless steel
25 Locking screw DIN-913 A2
26 Ring pin DIN- 1481 32
33
27 Lever stem 1.4034
28 Cam GGG-40.3
29 Packing Graphite
30 Gland 1.4305
31 Nut DIN-1471 31
32 O - Ring retainer 1.4031 'O' - ring seal
33 O - Ring According to service
34 Gland nut Carbon steel
35 Gasket ( relief only ) Asbestos free
36 Gasket ( relief only ) Asbestos free

4 IM-S13-12 CH Issue 3
 4
26

20 19

18
14

36 16

13
10

15

3
11
10 12
35
9 6

24
21
22

25
2

23

7
5

IM-S13-12 CH Issue 3 5
 2. Supply
Normally, the valve will be supplied set at the carried out by an authorised/competent person.
required pressure and sealed. Spirax Sarco accepts no responsibility for
BS 6759, DIN 3320 and local regulations requires valves which have been reset by unauthorised
that the setting of the valve should only be persons.

3. Before fitting the valve

3.1 Ensure that the installation is correct cause damage, leading to seat leakage.
(Fig. 1), Page 2. Blowdown must be carried out before
3.2 Blow through pipework to ensure that it is installing the safety valve.
completely free of any foreign matter that 3.3 Ensure that valve is set to the correct
may otherwise pass to the valve seat and pressure, see section 7.

4. Installation
4.1 The valve should always be mounted 4.7 The outlet pipework should be adequately
vertically upwards with its main axis vertical. supported such that it does not place undue
4.2 The valve should be fitted to the pipework stress on the safety valve.
or vessel by means of the shortest possible 4.8 Where the outlet pipework is directed
length of pipe or fitting. upwards a small bore drain should be
4.3 There should be no intervening valve or provided at the lowest point. (Fig. 3)
fitting i.e. it should not be possible to isolate This drain should be taken to a place where
safety valve. (Fig. 2) any discharge will not create a hazard
4.4 The inlet pipe connection should not be or inconvenience.
smaller than the valve.(See Fig. 5 and 6) 4.9 Each safety valve should have its own
4.5 The outlet pipe size should be equal or larger unrestricted discharge pipe.
than the valve outlet to keep back pressure 4.10 Valves with open bonnets may release fluid
below 12% of the set pressure. under pressure when discharging. Ensure
4.6 Direct the outlet pipework to a safe point of this can be done safely.
discharge where there is no risk of injury to 4.11 Safety valve should not be lagged.
persons or damage to property in the event 4.12 Safety valves can operate very suddenly
of the valve operating. and will be too hot to touch without
protection when installed on steam
systems.

Discharge to

73
safe area

Small bore
Fig 2 Fig 3 drain to safe area

6 IM-S13-12 CH Issue 3
 5. Damage prevention
Excessive pressure loss at the inlet of a safety
valve when it operates will cause extremely
rapid opening and closing of the valve,
observed as chattering or hammering.
This may result in reduced capacity as well as
damage to seating faces and the other parts of the
valve.
When normal pressure is restored it is possible
that the valve will leak.
Solution
BS 6759 makes the following
recommendations to prevent these problems.
Valve should be fitted 8-10 pipe diameters 8 - 10 Pipe diameters downstream
downstream of Converging or Diverging of converging "Y" fittings or bends
Fittings or Bends. (Fig. 4)
Inlet branches should be as Fig. 5 or Fig. 6. Fig 4

r
A

Fig 5 Fig 6
Radius "r" not less than inlet diameter Inlet area "A" approx. twice that of inlet of area "a".

6. Commissioning
6.1 Once the valve has been fitted check that overpressure is limited to 5% of the
there are no leaks from either the inlet or safety valve setting.
the outlet connections. 6.3 Reduce the system pressure to the normal
6.2 Test the valve by raising the system operating pressure and check that the safety
pressure. Check that the valve operates valve reseats.
at the correct set pressure and that the

IM-S13-12 CH Issue 3 7
 7. Testing during use
It is recommended that the safety valve be * Note: Use suitable protection against excess
tested for correct operation at least once every heat and noise when testing safety valves,
six months*, as outlined in Section 6, or by period between safety valve tests to be agreed
manual lifting when the operating pressure is by responsible person or insurance company.
no more than 85% of the safety valve set (Check local requirements for frequency of
pressure. testing).

8. Guidelines for setting

(By Authorised Persons Only)
7.1 Choice of Set Pressure pressure is restored.
A decision must be made regarding the Fig. 7 outlines the way a safety valve operates.
pressure at which the safety valve should be It can be seen that the safety valve does not
set. re-seat when the pressure falls to the safety
The maximum set pressure, in accordance valve set pressure.
with BS5500, is the safe working pressure of There must be adequate differential between
the plant it protects and the valve must the maximum system operating pressure and
achieve its rated capacity with an the safety valve set pressure if the valve is to
overpressure of no more than 10%. re-seat.
The SV5 achieves its rated capacity at 5% The maximum system operating pressure is
over pressure. If the valve is set too close to most likely to occur during no-load conditions.
the operating pressure of the system the valve Fig. 8 shows the range within which the valve
may operate prematurely. It will also fail to must be set.
close satisfactorily when normal operating

5% of set pressure Max allowable Max setting of

Full lift position working pressure safety valve
Safety valve may
Reseat differential or design pressure be set within
Set of vessel
pressure this range
Min setting of
safety valve
Pressure

(Valve operates) Reseat pressure

(10% of set pressure) Max system A Reseat differential
operating pressure
Time
No load condition
B
Fig 7 Operating pressure

Note: The operating pressure of a system will Fig 8

vary and it is important that the safety valve is
set high enough to accommodate such Flow rate = Max rating of pressure reducing
fluctuations. valve

7.2 Setting the Valve A = 10% of Safety valve set pressure,

British Standard 6759 and DIN 3320 requires 0.3 bar minimum
that a safety valve should only be set by an B Normal system pressure variation
Authorised Person.
Spirax Sarco cannot be held responsible for
unauthorised alteration of the set pressure.

8 IM-S13-12 CH Issue 3
 9. Maintenance
All safety valves should receive planned
maintenance.
It is recommended that the Spirax Sarco
SV5 safety valves are returned to Spirax
Sarco, or an approved Spirax Sarco agent,
for a thorough overhaul periodically. The valve
will be returned having been overhauled, tested
re-set and sealed in accordance with BS6759.

IM-S13-12 CH Issue 3 9
10 IM-S13-12 CH Issue 3
IM-S13-12 CH Issue 3 11
12 IM-S13-12 CH Issue 3