https://www.academia.

edu/10123577/Tabel_Konversi_
Nilai_Kekerasan

BUEHLER

Hardness
Conversion
Charts
 Hardness Conversion Charts

Introduction

The requirement to convert from one hardness test scale to another is quite common and as such is covered by various
International Standards (ASTM E140, ISO 18265). These standards point out that, due to the differences in the various types
of hardness test methods, it is not possible to show a constant conversion relationship across all materials. As such, the
standards provide approximate conversions only with defined hardness ranges and test loads for specific materials. Thus
there are a number of conversion tables according to material type and it is essential to use the correct one. The following
conversion charts have been constructed according to the hardness test scale conversion algorithms provided within ASTM
E140. Please treat all converted values as approximations only.

The table below lists the scales present in the following tables and any restrictions on the load ranges valid for the
conversions.

Scale Symbol Indenter and Load force

Vickers HV Vickers diamond, nickel alloys (1, 5, 10 or 30-kgf),
copper (100-gf), aluminum (15-kgf)
Knoop HK Knoop diamond, 500-gf and over
Rockwell A HRA Diamond, 60-kgf
Rockwell B HRB Steel ball 116, 100-kgf
Rockwell C HRC Diamond, 150-kgf
Rockwell D HRD Diamond, 100-kgf
Rockwell E HRE Steel ball 18, 100-kgf
Rockwell F HRF Steel ball 116, 60-kgf
Rockwell G HRG Steel ball 116, 150-kgf
Rockwell H HRH Steel ball 18, 60-kgf
Rockwell K HRK Steel ball 18, 150-kgf
Superficial Rockwell 15N HR15N Diamond, 15-kgf
Superficial Rockwell 30N HR30N Diamond, 30-kgf
Superficial Rockwell 45N HR45N Diamond, 45-kgf
Superficial Rockwell 15T HR15T Steel ball 116, 15-kgf
Superficial Rockwell 30T HR30T Steel ball 116, 30-kgf
Superficial Rockwell 45T HR45T Steel ball 116, 45-kgf
Superficial Rockwell 15W HR15W Steel ball 18, 15-kgf
Brinell HBW Tungsten carbide 10mm ball, 3000-kgf
Brinell HBS Steel 10mm ball, steel and nickel (3000-kgf),
brass and aluminum (500-kgf)

A commonly asked question is "How come my results and those from another facility are different?" The first step is to use
statistical analysis to see if the difference is significant. Next, determine any differences in the test method. The two most
common problems relate to either a different load being applied or a converted value being compared with an actual
measurement. For this reason, it is recommended that the measured value is included in parenthesis following the
conversion when reporting a converted hardness number.
In addition to steel balls, tungsten carbide balls have been introduced for Rockwell and Rockwell Superficial scales. However,
all of the equations applied to create values for the tables in this document are based on empirical test accomplished with
steel indenters. A Rockwell hardness test done with a tungsten carbide ball may yield slightly different results.
 Hardness Conversion Charts

Table of Contents
Hardness Conversion Chart for Non-Austenitic Steels (Rockwell C Range) . . . . . . . . . . . . . .1

Hardness Conversion Chart for Non-Austenitic Steels (Rockwell B Range) . . . . . . . . . . . . . .3

Hardness Conversion Chart for Austenitic Stainless Steel Sheet (Rockwell C Range) . . . . . . . . . . .4

Hardness Conversion Chart for Austenitic Stainless Steel Sheet (Rockwell B Range) . . . . . . . . . . . . .5

Hardness Conversion Chart for Nickel and High-Nickel Alloys . . . . . . . . . . . . . . . . . . . . . . . .6

Hardness Conversion Chart for Cartridge Brass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Hardness Conversion Chart for Copper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Hardness Conversion Chart for Wrought Aluminum Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Common Applications and Nomenclature for Hardness Tests . . . . . . . . . . . . . . . . . . . . . . .10

 Hardness Conversion Chart for Non-Austenitic Steels (Rockwell C Range)

HV HK HRC HRA HRD HR15N HR30N HR45N HBW

950 917 68.0 85.7 76.9 93.4 84.7 75.9
940 912 67.8 85.6 76.7 93.3 84.5 75.7
930 907 67.6 85.5 76.6 93.2 84.3 75.4
920 902 67.4 85.3 76.4 93.1 84.1 75.2
910 897 67.2 85.2 76.2 93.0 83.9 74.9
900 891 66.9 85.1 76.1 92.9 83.7 74.6
890 885 66.7 84.9 75.9 92.8 83.5 74.3
880 880 66.4 84.8 75.7 92.7 83.3 74.0
870 874 66.2 84.6 75.5 92.6 83.0 73.7
860 867 65.9 84.5 75.3 92.5 82.8 73.4
850 860 65.6 84.3 75.0 92.4 82.5 73.1
840 854 65.3 84.2 74.8 92.3 82.3 72.7
830 847 65.0 84.0 74.6 92.2 82.0 72.4
820 840 64.7 83.8 74.3 92.1 81.7 72.0
810 833 64.4 83.6 74.1 91.9 81.4 71.7
800 825 64.1 83.4 73.9 91.8 81.1 71.3
790 817 63.7 83.3 73.6 91.7 80.8 70.9
780 809 63.4 83.1 73.3 91.5 80.5 70.5
770 801 63.0 82.9 73.0 91.4 80.2 70.1
760 793 62.7 82.7 72.8 91.2 79.9 69.6
750 784 62.3 82.5 72.5 91.1 79.5 69.2
740 776 61.9 82.2 72.2 90.9 79.2 68.7
730 767 61.5 82.0 71.9 90.7 78.8 68.3
720 758 61.1 81.8 71.6 90.6 78.4 67.8
710 749 60.7 81.6 71.2 90.4 78.1 67.3
700 739 60.2 81.3 70.9 90.2 77.7 66.8
690 730 59.8 81.1 70.6 90.0 77.3 66.3
680 720 59.3 80.8 70.2 89.8 76.9 65.7 645
670 710 58.9 80.6 69.9 89.6 76.4 65.2 634
660 700 58.4 80.3 69.5 89.4 76.0 64.6 623
650 690 57.9 80.0 69.1 89.2 75.6 64.1 613
640 679 57.4 79.8 68.7 89.0 75.1 63.5 603
630 669 56.9 79.5 68.3 88.7 74.7 62.9 593
620 658 56.4 79.2 67.9 88.5 74.2 62.3 583
610 647 55.8 78.9 67.5 88.3 73.7 61.6 573
600 637 55.3 78.6 67.1 88.0 73.2 61.0 563
590 626 54.7 78.3 66.7 87.8 72.7 60.3 554
580 614 54.1 78.0 66.2 87.5 72.2 59.7 544
570 603 53.5 77.6 65.8 87.2 71.7 59.0 535
560 592 52.9 77.3 65.3 86.9 71.1 58.2 525
550 581 52.3 77.0 64.8 86.6 70.5 57.5 516
540 570 51.7 76.6 64.3 86.3 70.0 56.8 507
530 558 51.0 76.3 63.8 86.0 69.4 56.0 497
1
 Hardness Conversion Chart for Non-Austenitic Steels (Rockwell C Range)

HV HK HRC HRA HRD HR15N HR30N HR45N HBW

520 547 50.4 75.9 63.3 85.7 68.8 55.2 488
510 535 49.7 75.6 62.8 85.4 68.2 54.4 479
500 524 49.0 75.2 62.3 85.0 67.5 53.6 470
490 513 48.3 74.8 61.7 84.7 66.9 52.8 460
480 501 47.5 74.4 61.1 84.3 66.2 51.9 451
470 490 46.8 74.0 60.6 83.9 65.6 51.0 442
460 479 46.0 73.6 60.0 83.5 64.8 50.1 433
450 467 45.2 73.2 59.4 83.1 64.1 49.2 424
440 456 44.4 72.7 58.7 82.7 63.4 48.2 415
430 445 43.5 72.3 58.1 82.3 62.6 47.2 406
420 434 42.7 71.8 57.4 81.8 61.9 46.2 396
410 423 41.8 71.4 56.7 81.4 61.0 45.2 387
400 412 40.9 70.9 56.0 80.9 60.2 44.1 378
390 402 39.9 70.4 55.3 80.4 59.4 43.0 369
380 391 38.9 69.9 54.5 79.9 58.5 41.8 360
370 380 37.9 69.4 53.8 79.3 57.6 40.7 351
360 370 36.9 68.8 53.0 78.8 56.6 39.4 341
350 359 35.8 68.3 52.1 78.2 55.7 38.2 332
340 349 34.7 67.7 51.3 77.5 54.7 36.9 323
330 339 33.5 67.1 50.4 76.9 53.6 35.5 314
320 329 32.3 66.5 49.5 76.3 52.5 34.1 304
310 319 31.1 65.9 48.5 75.5 51.4 32.6 295
300 309 29.8 65.2 47.5 74.8 50.2 31.1 285
290 300 28.4 64.6 46.5 74.1 49.0 29.5 276
280 290 27.0 63.9 45.4 73.3 47.7 27.9 266
270 281 25.5 63.1 44.2 72.5 46.4 26.1 257
260 271 23.9 62.3 43.0 71.6 45.0 24.3 247
250 262 22.3 61.5 41.8 70.7 43.5 22.3 237
240 253 20.5 60.7 40.4 69.7 41.9 20.3 228

The non-austenitic steels included carbon, alloy and tool steels in the as-forged, annealed, normalized, and quenched and tempered conditions.

2
 Hardness Conversion Chart for Non-Austenitic Steels (Rockwell B Range)

HV HK HRB HRA HRF HR15T HR30T HR45T HBS

240 252 99.8 61.4 93.0 83.0 72.7 240
235 248 99.1 60.9 92.8 82.5 72.0 235
230 243 98.4 60.4 92.6 82.0 71.2 230
225 239 97.6 59.9 92.3 81.5 70.5 225
220 235 96.8 59.4 92.1 81.0 69.7 220
215 230 95.9 58.8 91.8 80.4 68.8 215
210 225 95.1 58.3 91.5 79.8 67.9 210
205 221 94.1 57.7 91.2 79.2 67.0 205
200 216 93.2 57.1 90.9 78.6 66.0 200
195 211 92.2 56.5 90.6 77.9 65.0 195
190 205 91.1 55.8 90.2 77.1 63.9 190
185 200 90.0 55.1 89.8 76.4 62.8 185
180 195 88.8 54.4 89.4 75.6 61.6 180
175 190 87.5 53.7 89.1 74.8 60.4 175
170 185 86.2 52.9 88.6 73.9 59.0 170
165 180 84.8 52.2 88.2 72.9 57.6 165
160 174 83.3 51.3 87.7 72.0 56.1 160
155 169 81.7 50.5 87.2 70.9 54.6 155
150 164 80.1 49.5 86.6 69.8 52.9 150
145 159 78.3 48.6 86.1 68.6 51.1 145
140 154 76.4 47.6 85.5 67.4 49.2 140
135 149 74.4 46.5 99.3 84.8 66.0 47.2 135
130 143 72.2 45.4 98.1 84.1 64.6 45.0 130
125 138 69.9 44.3 96.7 83.3 63.0 42.7 125
120 133 67.4 43.0 95.3 82.5 61.3 40.2 120
115 128 64.7 41.7 93.8 81.7 59.5 37.5 115
110 123 61.8 40.3 92.1 80.7 57.6 34.5 110
105 118 58.6 38.8 90.3 79.7 55.4 31.3 105
100 113 55.1 37.3 88.3 78.5 53.1 27.8 100
95 109 51.3 35.5 86.1 77.3 50.5 24.0 95
90 104 47.1 33.7 83.7 75.9 47.7 19.7 90
85 99 42.4 31.7 81.1 74.4 44.6 15.0 85
80 94 37.1 29.5 78.1 72.7 41.1 9.8 80
75 89 31.2 27.2 74.7 70.8 37.1 75

The non-austenitic steels included carbon, alloy and tool steels in the as-forged, annealed, normalized, and quenched and tempered conditions.

3
 Hardness Conversion Chart for Austenitic Stainless Steel Sheet (Rockwell C Range)

HRC HRA HR15N HR30N HR45N

48 74.4 84.1 66.2 52.1
47 73.9 83.6 65.3 51.0
46 73.4 83.1 64.5 49.8
45 72.9 82.6 63.6 48.7
44 72.4 82.1 62.8 47.5
43 71.9 81.6 61.8 46.5
42 71.4 81.1 61.0 45.3
41 70.9 80.5 60.1 44.2
40 70.4 80.0 59.2 43.0
39 69.9 79.5 58.4 41.9
38 69.4 79.0 57.5 40.7
37 68.8 78.5 56.6 39.6
36 68.3 78.0 55.7 38.4
35 67.8 77.5 54.9 37.3
34 67.3 77.0 54.0 36.1
33 66.8 76.5 53.1 35.0
32 66.3 75.9 52.3 33.9
31 65.8 75.4 51.4 32.7
30 65.3 74.9 50.5 31.6
29 64.8 74.4 49.6 30.5
28 64.3 73.9 48.8 29.3
27 63.8 73.4 47.9 28.2
26 63.3 72.9 47.0 27.0
25 62.8 72.4 46.2 25.9
24 62.3 71.9 45.3 24.8
23 61.8 71.3 44.4 23.6
22 61.3 70.8 43.5 22.5
21 60.8 70.3 42.7 21.3
20 60.3 69.8 41.8 20.2

The austenitic stainless steel sheet included in the original testing was as follows: Types 201, 202, 301, 302, 304, 304L, 305, 316, 316L, 321 and 347.

4
 Table 4 Hardness Conversion Chart for Austenitic Stainless Steel Sheet (Rockwell B Range)
Hardness Conversion Chart for Austenitic Stainless Steel Sheet (Rockwell B Range)

HRB HRA HRF HR15T HR30T HR45T

100 61.5 91.5 80.4 70.2
99 60.9 91.2 79.8 69.2
98 60.3 90.8 79.1 68.2
97 59.7 90.4 78.4 67.2
96 59.1 90.1 77.7 66.1
95 58.6 89.7 77.0 65.1
94 58.0 89.3 76.3 64.1
93 57.4 88.9 75.6 63.1
92 56.8 88.6 74.9 62.1
91 56.2 88.2 74.2 61.1
90 55.6 87.8 73.5 60.1
89 55.0 87.5 72.8 59.0
88 54.5 87.1 72.1 58.0
87 53.9 86.7 71.4 57.0
86 53.3 86.4 70.7 56.0
85 52.7 86.0 70.0 55.0
84 52.1 85.6 69.3 54.0
83 51.5 85.2 68.6 52.9
82 50.9 84.9 67.9 51.9
81 50.4 84.5 67.2 50.9
80 49.8 84.1 66.5 49.9
79 49.2 99.6 83.8 65.8 48.9
78 48.6 99.0 83.4 65.1 47.9
77 48.0 98.3 83.0 64.5 46.8
76 47.4 97.6 82.6 63.7 45.8
75 46.9 96.9 82.3 63.1 44.8
74 46.3 96.2 81.9 62.4 43.8
73 45.7 95.6 81.5 61.7 42.8
72 45.1 94.9 81.2 61.0 41.8
71 44.5 94.2 80.8 60.3 40.7
70 43.9 93.5 80.4 59.6 39.7
69 43.4 92.9 80.1 58.9 38.7
68 42.8 92.2 79.7 58.2 37.7
67 42.2 91.5 79.3 57.5 36.7
66 41.6 90.8 78.9 56.8 35.7
65 41.0 90.1 78.6 56.1 34.7
64 40.4 89.5 78.2 55.4 33.6
63 39.8 88.8 77.8 54.7 32.6
62 39.3 88.1 77.5 54.0 31.6
61 38.7 87.4 77.1 53.3 30.6
60 38.1 86.8 76.7 52.6 29.6

The austenitic stainless steel sheet included in the original testing was as follows: Types 201, 202, 301, 302, 304, 304L, 305, 316, 316L, 321 and 347.

5
 Table 4 Hardness Conversion Chart for Austenitic Stainless Steel Sheet (Rockwell B Range)
Hardness Conversion Chart for Nickel and High-Nickel Alloys

HV HK HRA HRB HRC HRD HRE HRF HRG HRK HR15N HR30N HR45N HR15T HR30T HR45T HBS
520 75.4 50.0 63.1 85.5 68.2 54.7
500 74.8 48.9 62.2 84.9 67.1 53.3
480 74.2 47.6 61.2 84.3 66.0 51.9 449
460 73.6 46.3 60.2 83.6 64.9 50.3 432
440 72.9 44.8 59.1 82.9 63.6 48.6 414
420 72.1 43.3 57.9 82.1 62.3 46.8 397
400 71.3 41.6 56.6 81.3 60.8 44.9 379
380 433 70.4 39.8 55.2 80.4 59.3 42.8 361
360 411 69.4 37.8 53.7 79.5 57.6 40.6 343
340 388 68.3 37.8 53.7 78.4 55.7 38.1 325
320 365 67.2 33.3 50.3 77.2 53.7 35.4 94.9 86.3 77.4 307
300 342 65.9 30.7 48.4 76.0 51.5 32.5 94.4 85.2 75.9 289
280 320 64.5 27.9 46.2 90.0 74.5 49.0 29.2 93.7 84.0 74.2 271
260 297 62.8 24.6 43.7 86.7 72.9 46.3 25.5 93.0 82.6 72.2 252
240 274 61.0 99.0 21.0 41.0 82.9 71.2 43.1 21.5 92.1 80.9 69.9 234
220 251 59.0 96.1 37.9 78.3 69.1 39.6 16.8 91.0 78.9 67.1 215
200 228 56.6 92.5 34.3 72.8 96.9 66.8 35.6 11.4 89.8 76.5 63.8 196
195 223 55.9 91.5 33.4 71.2 96.0 66.1 34.4 10.0 89.5 75.8 62.8 191
190 217 55.3 90.5 32.3 69.6 95.0 65.4 33.3 8.4 89.1 75.1 61.8 187
185 211 54.5 89.4 31.3 67.9 94.0 64.7 32.1 6.8 88.7 74.4 60.8 182
180 206 53.8 88.2 30.2 66.1 93.0 64.0 30.8 5.2 88.3 73.6 59.7 177
175 200 53.0 87.0 29.0 64.2 91.9 63.2 29.5 87.9 72.8 58.5 172
170 194 52.2 85.7 27.8 62.1 90.7 62.4 28.1 87.4 71.9 57.2 167
165 189 51.4 84.3 26.6 60.0 89.4 61.6 26.7 86.9 71.0 55.9 163
160 183 50.5 82.9 25.3 57.7 88.1 86.4 70.0 54.4 158
155 177 49.6 81.3 23.9 55.2 86.7 85.8 68.9 52.9 153
150 171 48.6 79.6 22.4 52.7 85.2 85.2 67.8 51.3 148
145 166 47.6 77.9 20.9 49.9 83.5 84.6 66.6 49.5 143
140 160 46.5 75.9 99.4 99.5 46.9 81.8 83.9 65.3 47.6 139
135 154 45.3 73.9 98.1 98.3 43.7 79.9 83.2 63.9 45.6 134
130 149 44.1 71.7 96.7 97.0 40.3 77.9 82.4 62.4 43.4 129
125 143 42.8 69.3 95.2 95.7 36.5 75.8 81.6 60.8 41.0 124
120 137 41.4 66.7 93.5 94.2 32.5 73.4 80.7 59.1 38.4 119
115 132 40.0 63.9 91.8 92.5 70.9 79.7 57.1 35.5 114
110 126 60.9 89.8 90.8 68.1 78.6 55.1 32.4 110
105 120 57.5 87.7 88.8 65.0 77.4 52.8 28.9 105
100 115 53.8 85.3 86.7 61.7 76.1 50.3 25.0 100
95 109 49.8 82.7 84.4 58.0 74.7 47.5 20.7 95
90 103 45.2 79.8 81.8 53.8 73.1 44.4 15.9 90
85 97 40.2 76.5 78.8 49.2 71.2 40.9 10.4 85
80 92 34.5 72.9 75.6 44.0 69.2 37.0 80
75 86 28.0 68.8 71.8 38.2 66.9 32.6 75

6
 Table 4 Hardness Conversion Chart for Austenitic Stainless Steel Sheet (Rockwell B Range)
Hardness Conversion Chart for Cartridge Brass

HV HRB HRF HR15T HR30T HR45T HBS

195 93.4 109.8 89.9 77.0 65.6 169
190 92.2 109.2 89.6 76.3 64.5 164
185 90.9 108.5 89.3 75.6 63.3 160
180 89.6 107.8 89.0 74.9 62.1 156
175 88.2 107.0 88.6 74.1 60.8 152
170 86.7 106.2 88.3 73.3 59.5 148
165 85.2 105.4 87.9 72.4 58.1 143
160 83.6 104.6 87.4 71.5 56.6 139
155 82.0 103.6 87.0 70.5 55.0 135
150 80.2 102.7 86.5 69.5 53.4 131
145 78.3 101.7 85.9 68.4 51.7 127
140 76.4 100.6 85.4 67.2 49.8 122
135 74.3 99.4 84.8 65.9 47.9 118
130 72.1 98.2 84.1 64.5 45.8 114
125 69.8 96.9 83.4 63.0 43.6 110
120 67.3 95.5 82.6 61.4 41.2 106
115 64.6 94.0 81.7 59.6 38.6 101
110 61.7 92.4 80.7 57.7 35.7 97
105 58.5 90.6 79.7 55.6 32.6 93
100 55.1 88.7 78.5 53.2 29.2 89
95 51.4 86.6 77.2 50.7 25.3 85
90 47.3 84.3 75.8 47.8 21.0 80
85 42.7 81.8 74.1 44.6 16.0 76
80 37.6 78.9 72.3 41.1 10.0 72
75 31.9 75.7 70.3 37.0 68
70 25.3 72.1 68.0 32.4 63
65 17.5 67.9 65.4 27.0 59
60 63.0 62.4 20.7 55
55 57.2 59.1 13.3 51
50 50.1 55.4 47
45 41.0 43

7
 Table 4 Hardness Conversion Chart for Austenitic Stainless Steel Sheet (Rockwell B Range)
Hardness Conversion Chart for Copper

HV HK HRB HRF HR15T HR30T HR45T HBS

126 133 66.6 97.9 87.1 68.7 48.0 118
124 131 65.2 97.2 86.7 67.7 46.7 116
122 129 63.8 96.4 86.4 66.8 45.3 113
120 127 62.3 95.7 86.0 65.8 43.8 111
118 125 60.7 94.9 85.6 64.8 42.4 109
116 122 59.0 94.0 85.2 63.7 40.9 106
114 120 57.3 93.1 84.8 62.6 39.3 104
112 118 55.4 92.2 84.3 61.4 37.7 102
110 116 53.5 91.2 83.8 60.2 36.0 100
108 114 51.5 90.2 83.3 58.9 34.3 97
106 111 49.4 89.1 82.8 57.6 32.5 95
104 109 47.2 87.9 82.2 56.3 30.6 93
102 107 44.9 86.7 81.5 54.8 28.7 91
100 104 42.5 85.5 80.8 53.4 26.7 88
98 102 39.9 84.1 80.2 51.8 24.6 86
94 100 37.3 82.7 79.4 50.2 22.4 84
96 98 34.5 81.2 78.6 48.5 20.0 82
92 95 31.7 79.7 77.7 46.8 17.6 80
90 93 28.7 78.0 76.7 44.9 15.1 77
88 91 25.6 76.3 75.7 43.0 12.4 75
86 88 22.5 74.5 74.6 41.1 73
84 86 19.2 72.6 73.4 39.0 71
82 83 15.8 70.6 72.1 36.8 69
80 81 12.4 68.5 70.6 34.6 67
78 79 8.8 66.3 69.1 32.3 64
76 76 64.1 67.5 29.8 62
74 74 61.8 65.7 27.3 60
72 71 59.3 63.8 24.7 58
70 69 56.8 61.8 21.9 56
68 66 54.3 59.7 19.0 54
66 64 51.6 57.5 16.0 52
64 61 48.8 55.2 12.9 50
62 59 46.0 52.9 8.2 47
60 56 43.1 50.5 45
58 53 40.1 48.1 43
56 51 36.9 45.6 41
54 48 33.7 43.1
52 45 30.3 40.6

The copper included in the original testing was UNS C10200 to C14200 inclusive. The conversions are listed for strip 0.040 in (1.02 mm) or greater in thickness.

8
 Table 4 Hardness Conversion Chart for Austenitic Stainless Steel Sheet (Rockwell B Range)
Hardness Conversion Chart for Wrought Aluminum Products

HV HRB HRE HRH HR15T HR30T HR15W HBS

190 91.8 89.2 77.2 95.1 161
185 90.7 89.0 76.4 94.8 156
180 89.5 88.7 75.5 94.6 152
175 88.2 88.5 74.6 94.2 148
170 86.8 88.2 73.7 94.0 144
165 85.3 87.9 72.6 93.7 140
160 83.7 87.6 71.5 93.3 136
155 81.9 87.2 70.4 93.0 132
150 79.9 86.8 69.1 92.7 128
145 77.8 86.4 67.8 92.4 123
140 75.4 86.0 66.5 92.0 119
135 72.8 85.5 65.0 91.6 115
130 69.9 99.6 84.9 63.5 91.3 111
125 66.7 98.6 84.3 61.9 90.9 107
120 63.3 97.4 83.5 60.2 90.4 103
115 59.6 96.2 82.9 58.4 90.0 99
110 55.6 94.8 82.0 56.6 89.5 95
105 51.3 93.2 81.0 54.7 89.0 90
100 46.9 91.3 107.3 79.9 52.7 88.5 86
95 42.3 89.2 106.3 78.7 50.7 87.9 82
90 37.6 86.7 105.0 77.3 48.5 87.3 78
85 32.8 83.8 103.7 75.8 46.3 86.6 74
80 27.9 80.4 102.0 74.1 44.0 85.9 70
75 76.5 100.2 72.2 85.1 66
70 72.2 98.1 70.3 84.1 62
65 67.5 95.7 68.3 83.1 57
60 62.6 93.0 66.2 81.8 53
55 57.6 90.1 64.0 80.4 49
50 52.6 87.0 61.8 78.7 45
45 47.4 83.7 59.5 76.9 41

9
 Common Applications and Nomenclature for Hardness Tests

Test Indentation
Test Symbol Indenter Force (kg) depth (mm)* Application
Rockwell A HRA diamond 60 (100 - HRA value) / 500 Very hard materials,
cemented carbides
Rockwell B HRB 1
16 ball 100 (130 - HRB value) / 500 Low strength steel, copper
alloys, aluminum alloys,
malleable iron
Rockwell C HRC diamond 150 (100 - HRC value) / 500 High strength steel,
titanium, pearlitic
malleable iron
Rockwell D HRD diamond 100 (100 - HRD value) / 500 High strength steel, thin
steel
Rockwell E HRE 1
8 ball 100 (130 - HRE value) / 500 Cast iron, aluminum and
magnesium alloys
Rockwell F HRF 1
16 ball 60 (130 - HRF value) / 500 Annealed copper alloys,
thin soft metals
Rockwell G HRG 1
16 ball 150 (130 - HRG value) / 500 Phosphor bronze,
beryllium copper,
malleable irons**
Rockwell H HRH 1
8 ball 60 (130 - HRH value) / 500 Aluminum, zinc, lead
Rockwell K HRK 1
8 ball 150 (130 - HRK value) / 500
Rockwell L HRL ball 60 (130 - HRL value) / 500 Bearing metals and other
Rockwell M HRM ball 100 (130 - HRM value) / 500 very soft or thin materials,
including plastics. Use
Rockwell P HRP ball 150 (130 - HRP value) / 500
smallest ball and heaviest
Rockwell R HRR ball 60 (130 - HRR value) / 500 load that do not give anvil
Rockwell S HRS ball 100 (130 - HRS value) / 500 effect.
Rockwell V HRV ball 150 (130 - HRV value) / 500
Superficial HR15N diamond 15 (100 - HR15N value) / 1000 Cemented carbides, thin
Rockwell N steel and case hardened
Superficial HR30N diamond 30 (100 - HR30N value) / 1000 steel, hard cast irons,
Rockwell N titanium, and other
materials harder than
Superficial HR45N diamond 45 (100 - HR45N value) / 1000
100HRB
Rockwell N
Superficial HR15T 1
16 ball 15 (100 - HR15T value) / 1000
Rockwell T Copper alloys, phosphor
bronze, soft steels,
Superficial HR30T 1
16 ball 30 (100 - HR30T value) / 1000
Rockwell T aluminum alloys,
malleable iron, thin soft
Superficial HR45T 1
16 ball 45 (100 - HR45T value) / 1000 sheet metals
Rockwell T

10
 Common Applications and Nomenclature for Hardness Tests

Test Indentation
Test Symbol Indenter Force (kg) depth (mm)* Application
Superficial HR15W 1
8 ball 15 (100 - HR15W value) / 1000
Rockwell W
Superficial HR30W 1
8 ball 30 (100 - HR30W value) / 1000
Rockwell W
Superficial HR45W 1
8 ball 45 (100 - HR45W value) / 1000
Rockwell W
Superficial HR15X ball 15 (100 - HR15X value) / 1000
Rockwell X
Cast iron, aluminum and
Superficial HR30X ball 30 (100 - HR30X value) / 1000
Rockwell X magnesium alloys,
bearing metals, zinc, lead
Superficial HR45X ball 45 (100 - HR45X value) / 1000
Rockwell X
Superficial HR15Y ball 15 (100 - HR15Y value) / 1000
Rockwell Y
Superficial HR30Y ball 30 (100 - HR30Y value) / 1000
Rockwell Y
Superficial HR45Y ball 45 (100 - HR45Y value) / 1000
Rockwell Y
Vickers - HV diamond 1-100 diagonal length in mm / 7 A wide range of materials
"Macro"
Vickers - HV diamond .005 to 1 diagonal length in mm / 7 A wide range of materials
"Micro"
Knoop HK diamond .005 to 1 diagonal length in mm/ 30 A wide range of materials,
case depth determination
*It is possible to determine the minimum recommended thickness of the test piece using the indentation depth. Rule of thumb is that the thickness should exceed 10
times the depth of the indentation with a diamond indenter and 15 times the depth of the indentation with a ball indenter.
EXAMPLE: A hardness reading of HRB 43 is observed

t = (130 - HRB) / 500

t = (130 - 43) / 500

t = 0.174 mm or 0.0071 in
Test Piece thickness should be 15 x t or 2.61 mm (0.1in)
**Upper limit is 92 HRG to avoid possible flattening of the ball.

11