www.stelpro.

com

Users Guide
STCNP - 5mA
Smart non programmable electronic
thermostat for heating cable

For further information or to consult this guide online,

please visit our Web site.
INSSTCNP5MA0612
 WARNING WARNING
Before installing and operating this product,
the owner and/or installer must read, under-
stand and follow these instructions and keep
them handy for future reference. If these in-
structions are not followed, the warranty will
be considered null and void and the manufac-
turer deems no further responsibility for this
product. Moreover, the following instruc-
tions must be adhered to in order to avoid
personal injuries or property damages,
serious injuries and potentially fatal elec-
tric shocks. All electric connections must be
made by a qualified electrician, according to
the electrical and building codes effective in
your region. Do NOT connect this product to
a supply source other than 120VAC, 208 VAC
or 240 VAC, and do not exceed the specified
load limits. Protect the heating system with
the appropriate circuit breaker or fuse. You
must regularly clean dirt accumulations on or
in the thermostat. Do NOT use fluid to clean
thermostat air vents. Do NOT use where ex-
posed to water.

2 INSSTCNP5MA0612
1. Description
The STCNP non programmable electronic thermostat can be
used to control heating floors with electrical current with a
resistive load ranging from 0 A to 16 A at 120/208/240 VAC.
It has an easy user interface. It keeps the temperature of a
room ( mode) and a floor ( mode) at a requested set
point with a high degree of accuracy.

Floor Mode (factory setting)

This control method is ideal in areas where you want a hot
floor at any time and when the temperature of the ambient
air can be high without causing discomfort. For example, in
a bathroom.

Ambient Mode / (you only have to press down the

A/F button to switch from one mode to the other)
This control method is ideal when you want a stable ambi-
ent air temperature (without fluctuation). Usually, this mode is
used in large and often occupied rooms where temperature
variations can be uncomfortable. For example, in a kitchen, a
living room or a bedroom.
Some factors cause variations in ambient air temperature.
They include large windows (heat losses or gains due to out-
side temperature) and other heat sources such as a central
heating system, a fireplace, etc. In all these cases, the
mode will ensure a uniform temperature.

This Thermostat is not compatible with the following

installations:
electrical current higher than 16 A with a resistive load
(3840 W @ 240 VAC, 3330 W @ 208 VAC and 1920 W @
120 VAC);
inductive load (presence of a contactor or relay); and
central heating system.

INSSTCNP5MA0612 3
Parts supplied:
one (1) thermostat;
two (2) mounting screws;
four (4) solderless connectors suitable for copper wires;
one (1) floor sensor.

2. Installation

Thermostat selection and sensor location

The thermostat must be mounted on a connection box, at
around 1.5 m (5 feet) above the floor level, on a section of the
wall exempt from pipes or air ducts.
Do not install the thermostat in a location where temperature
measurements could be altered. For example:
close to a window, on an external wall, or close to a door
leading outside;
exposed directly to the light or heat of the Sun, a lamp, a
fireplace or any other heat source;
close or in front of an air outlet;
close to concealed ducts or a chimney;
in a location with poor air flow (e.g. behind a door), or with
frequent air drafts (e.g. head of stairs).
To install the sensor, refer to the installation guide of your
heating floor.

Thermostat mounting and connection

1. Cut off power supply on lead wires at the elec-
trical panel in order to avoid any risk of electric
shock. Ensure that the thermostat will be installed
on a junction box located in an uninsulated wall.
2. Ensure that the air vents of the thermostat are clean and
clear of any obstructions.
3. Using a screwdriver, loosen the screw retaining the mount-
ing base and front part of the thermostat. Remove the front
4 INSSTCNP5MA0612
 part of the thermostat from the mounting base by tilting it

upward.
4. Align and secure the mounting base to the connection box

using the two screws supplied.

5. Route wires coming from the wall through the hole of the
mounting base and make the required connections us-
ing the Four-wire installation figure, and using the sup-
plied solderless connectors. A pair of wires (black) must
be connected to the power source (120-208-240 VAC)
and another pair (yellow) must be connected to the heat-
ing cable (refer to the drawings displayed on the back of
the thermostat). For connections with aluminum wires, you
must use CO/ALR connectors. Please note that thermo-
INSSTCNP5MA0612 5
 stat wires do not have polarity, meaning that any wire can
be connected to the other. Then, connect the wires of the
floor temperature sensor at the indicated location behind
the thermostat.

Four-wire installation
6. Reinstall the front part of the thermostat on the mounting

base and tighten the screw at the bottom of the unit.

7. T urn on the power.
8. Set the thermostat to the desired setting (see the following
section).

6 INSSTCNP5MA0612
3. Operation

(Ambient mode)

(Floor mode)

Security mode

Smart mode
Day mode
TEST
Night mode

GFCI button

Red Indicator
(GFCI Test)

First Start-up
At the first start-up, the thermostat is initially in the Day and
modes. The temperature is displayed in degrees Celsius
and the standard factory set point adjustment is 25C. The
maximum floor temperature is limited to 28C.

Maximum floor temperature limitation

At any time, the floor temperature (both in and modes)
is maintained at less than 28C (82F) in order to avoid over-
heating caused by an excessive heating request, which could
damage some materials or be detrimental for health.

INSSTCNP5MA0612 7
Temperature set points
The figures beside the icon indicate the temperature set
points (both in and modes). They can be displayed in
degrees Celsius or Fahrenheit (see Display in degrees Cel-
sius/Fahrenheit).
Out of any adjustment mode, press down the + button to in-
crease the set point, or the - button to decrease it. Set points
can only be adjusted by increments of 1 degree. To quickly
scroll through the set point values, press and hold down the
button. Both in Manual and Smart modes, the mode set
points can range between 3 and 35C and can only be ad-
justed by increments of 1C (from 37 to 95F; by increments
of 1F from the Fahrenheit mode). From mode, the set
points can range between 3 and 28C (from 37 to 82F).
In Day mode, you can turn off the thermostat by lowering the
set point below 3C (37F). The set point value displayed will
be --, and heating system start up will be impossible.

Day mode and Night mode

The thermostat includes a Day mode (Sun) and a Night mode
(Moon), both of them having their own independently adjust-
able and recorded set point. When switching from one mode
to the other, the system will automatically use the tempera-
ture set point corresponding to the Day/Night mode selected.
The and temperature are displayed by the figures un-
der the and icons, and the temperature set points are
displayed by the figures beside the icon, both in degrees
Celsius or Farenheit. The standard factory set point adjust-
ment is 25C for the Day/ mode (21C from the mode),
and 22C for the Night/ mode (18C from the mode).
In order to manually switch from one mode to the other,
simultaneously press down the + and - buttons and release
them immediately.

8 INSSTCNP5MA0612
Night mode timer
The Night mode features a timer that automatically returns
to the Day mode after a selectable time period. This timer
allows the temporary use of a temperature set point. The
standard factory adjustment of the timer is 8 hours. With
this adjustment, the thermostat automatically returns to Day
mode 8 hours after being switched to the Night mode. You
can switch from the mode to the mode without affect-
ing the timer adjustment.
For example, if you want a night temperature lower than the
day temperature, both Day/Night modes set points will first
have to be set at the desired temperatures. Before bedtime,
the Night mode temperature set point will be activated by
switching manually to the Night mode. The timer is set for the
duration of the night. The thermostat will automatically return
to the Day mode at the end of the night, and the Day mode
temperature set point, which is higher, will become effective
at this time.

Night mode timer adjustment procedure

1. First, switch to the Night mode by simultaneously pressing
down the + and - buttons and releasing them immediately.
2. From the Night mode, simultaneously press down the +
and - buttons for more than 3 seconds until the icon
starts to blink, indicating that the adjustment of the Night
mode timer is effective. The figures that replace the
mode temperature indicate the current adjustment of the
timer and hrs replaces the mode temperature.
3. If needed, adjust the timer by pressing down the + button
to increase the value, or the - button to decrease it. The
adjustment range is from 1 hour to 999 hours. To quickly
scroll through timer values, press and hold down the but-
ton.
4. When the adjustment is completed, release the buttons
and wait for 5 seconds to exit the adjustment function. The
thermostat will then return to the Night mode.
N.B. The Night mode timer will be automatically reinitialized
to the latest recorded value when switching from the
INSSTCNP5MA0612 9
 Day mode to the Night mode. It is not necessary to read-
just the timer every time you switch to the Night mode.
The timer is also reinitialized when this value is adjusted.
Once the timer has completed its cycle and when the
thermostat is in the Day mode, you must manually return
to the Night mode. If you want to automatically return
to the Night mode, the Smart mode must be selected.

Smart mode
The Smart mode, which is associated to the Night mode tim-
er, allows alternating between the Day/Night modes and the
two corresponding set points over a 24-hour period. Once
activated, this mode allows an automatic return to the Night
mode after 24 hours. The Smart mode allows you to define
two periods in a single day with different set points.
For example, if the Smart mode is activated and the Night
mode timer is set at 8 hours, the thermostat will be operat-
ing in the Night mode for 8 hours at the night temperature
set point. Then, it will return to the Day mode for 16 hours
operating at the day temperature set point. At the end of the
24-hour cycle, the thermostat will return to the Night mode,
and the cycle will start again. The 24-hour cycle starts with
the Night mode as soon as the Smart mode is activated. The
Smart mode activation should be made when you want to
return to the Night mode. The normal course of a cycle in the
Smart mode is as follows:
1- Night mode: activated for the duration of the Night mode
timer cycle. It returns to the Day mode when the timer
cycle is completed.
2- Day mode: activated for the remaining time of the 24-hour
cycle. It returns to the Night mode at the end of the 24-
hour cycle.

10 INSSTCNP5MA0612
Adjustment procedure of the Smart mode:
1. First, switch to the Night mode by simultaneously pressing
down the + and - buttons and releasing them immediately.
2. From the Night mode, simultaneously press down the +
and - buttons for more than 3 seconds, until the icon
starts to blink, indicating that the adjustment of the Night
mode timer is effective. The figures that replace the ambi-
ent temperature indicate the current timer adjustment. If
needed, adjust the timer by pressing down the + button to
increase the value, or the - button to decrease it. The Night
mode timer adjustment range is from 1 hour to 23 hours in
the Smart mode. To quickly scroll through the timer values,
press and hold down the button.
N.B. If you set the timer to any value exceeding 23 hours, it
will be impossible to activate the Smart mode and if it
was activated, the Smart mode will be deactivated.
3. Activate the Smart mode by simultaneously pressing down
the + and - buttons for at least 3 seconds. The icon will
appear. If the Smart mode was already activated, the same
procedure should be used to deactivate it.
4. When the adjustment is completed, release the buttons
and wait for 5 seconds to exit the adjustment function.
N.B. It is always possible to manually change the Day/Night
mode during a 24-hour cycle. In all cases, at the end of
the 24-hour cycle, the thermostat will return to the Night
mode and start a new cycle. It is thus not necessary
to readjust the Smart mode when a manual change is
made to the Day/Night mode. If the thermostat is set off
(--), the Smart mode will be deactivated.
When the power is restored after a power failure for example,
the Smart mode is deactivated and its corresponding icon is
blinking. The icon will stop to blink as soon as you will press
down a button.

Display in Degrees Celsius/Fahrenheit

The thermostat can display the ambient temperature and
INSSTCNP5MA0612 11
the set point in degrees Celsius (standard factory setting) or
Fahrenheit.

Adjustment procedure for degrees Celsius/Fahrenheit dis-

play.
1. To switch from the degrees Celsius to the degrees Fahren-
heit, and conversely, the thermostat must be from the Day
mode. If so, simultaneously press down the + and - buttons
for more than 3 seconds until the icon blinks.
2. Press down the + button to switch from the degrees Cel-
sius to the degrees Fahrenheit, and conversely. The degree
Celsius or Fahrenheit symbol is displayed.
3. When the adjustment is completed, do not press down any
button during 5 seconds to exit the adjustment function.

/ Mode
To switch from the mode to the mode, or conversely,
press down the A/F button (when you are not in any adjust-
ment mode). Then, the temperature set point will become the
same as the or mode temperature, as applicable.

Safe mode
If the thermostat fails to detect the presence of a floor sensor,
it will automatically revert to mode at a setpoint of 21C.
(with a maximum set point temperature of 24C)

Sensor Selection
If you want to use the STCNP thermostat of Stelpro Design
with a temperature sensor already installed in the floor (other
than the sensor supplied with this thermostat), you must con-
tact the Stelpro Design customer service to validate the com-
patibility between the sensor and the thermostat. You must
know the serial number and name of the installed sensor.

Temperature Control
The thermostat controls the / temperature (accord-
12 INSSTCNP5MA0612
ing to the / mode) with a high degree of accuracy.
When the heating starts or stops, it is normal to hear a clic
sound. It is the noise of the relay which opens or closes, as
applicable.

Backlighting
The screen lights up when you press down a button. If you
do not press down any button for more than 15 seconds, the
screen turns off.
N.B. If you press down the + or - button once when the back-
light is off, it will light up without changing the set point
value. The set point value will change only if you press
down one of these buttons again.
Ground-fault Circuit Interrupter (GFCI)
The GFCI is designed to reduce the risk of electric shock. It
can detect a leakage current of 5 mA. If a defect is detect-
ed, the GFCI device lights up, and both screen and heating
system circuit are deactivated. The GFCI can be reinitialized
either by pressing down the Test button or by disconnecting
the thermostat at the electrical panel.

Ground-fault circuit interrupter (GFCI) verification

It is important to verify the ground-fault circuit interrupter in-
stallation and operation on a monthly basis.

GFCI verification procedure

1- Increase the temperature set point until the heating power
bars are displayed (displayed beside the floor tempera-
ture).
2- Press down the Test button.
3- The following two cases can occur:
a) 
Successful test: The red indicator of the thermostat
lights up. In this case, press down once again the Test
button to reinitialize the ground-fault circuit interrupter,
the red indicator turns off.
b) Failed test: The red indicator does not light up and the
INSSTCNP5MA0612 13
 entire display blinks during 5 seconds. In this case, dis-
connect the heating system at the electrical panel.

Security mode
This mode imposes a maximum temperature set point which
is impossible to exceed regardless of the mode in progress.
However, it is still possible to lower the set point at your dis-
cretion. Please note that when the Security mode is activat-
ed, it is impossible to switch from the mode to the
mode, and conversely.
Procedures to activate Security mode.
1. To activate the Security mode, the thermostat should be in
Day mode. Exit any adjustment mode to manually adjust
the set point at the desired maximum value.
2. Simultaneously press down the + and - buttons during 10
seconds (note that after 3 seconds, the icon starts to
blink and the software version and date are displayed. Con-
tinue to press down these buttons).
3. After 10 seconds, the icon is displayed indicating that
the Security mode is activated. Then, release the buttons.
Procedures to deactivate Security mode.
1. To deactivate the Security mode, cut off the power supply
of the thermostat at the electrical panel and wait at least 20
seconds.
2. Restore the power supply to the thermostat. The icon
will blink during a maximum of 5 minutes, indicating that
you can deactivate the Security mode.
3. In Day mode, simultaneously press down the + and - but-
tons for more than 10 seconds. The icon will then be
hidden indicating that the Security mode is deactivated.

Parameter backup and power failures

The thermostat saves some parameters in its nonvolatile
memory in order to recovere them when power is restored
(e.g. after a power failure). These are the four set points (Day/

14 INSSTCNP5MA0612
Night/ / ), the Smart mode, the Security mode, the maxi-
mum set point of the Security mode, the Celsius/Fahrenheit
mode, the remaining time of the timer and the maximum floor
temperature. These parameters are saved every minutes
when a change occur, except for the Day/Night mode and
the remaining time of the timer, which are saved only if the
Smart mode was not activated.
Please note that the Smart mode is not automatically reacti-
vated when the power is restored, the icon blinks to in-
dicate that this mode was activated before the power failure
and that is now deactivated. Moreover, when the power is
restored, the Day/Night mode is recovered only if the Smart
mode was deactivated before. If not, the Day mode is auto-
matically reactivated. The Security mode is also reactivated if
it was activated before the failure. However, its icon blinks for
5 minutes and you can deactivate this mode by simultane-
ously pressing down the + and - buttons for 10 seconds. The
Security mode stays activated if you dont follow this process
and the icon stops blinking.

INSSTCNP5MA0612 15
4. Troubleshooting
Problem Solution
In normal operating conditions,
the thermostat housing can reach
The thermostat is hot. nearly 40C at maximum load. It
is normal and will not affect the
operation of the thermostat.
Check if the thermostat is properly
Heating is always on. connected. Refer to the installation
section.
Check if the thermostat is properly
Heating does not run even
connected and make sure the red
if the thermostat indicates
indicator is not lit. Refer to the
it is on.
installation section.
Check if the thermostat is properly
connected. Refer to the installation
The display does not come on.
section. Check the power supply at
the electrical panel.
The red indicator lights up
Contact customer service.
frequently.
Check the presence of an air
The displayed ambient stream or a heat source near
temperature is incorrect. the thermostat, and correct the
situation.
The display indicates E1*, Faulty thermal sensor. Contact
E2** or E3***. customer service.
Possibility of a bad contact. Check
Weak luminosity of the
thermostat wirings. Refer to the
display.
installation section.

* E1: Faulty ambient exterior sensor (open circuit) - written in the ambient section
** E2: Faulty interior sensor (open circuit) - written in the ambient section
*** E3: Faulty floor sensor (open circuit) - written in the floor section
N.B. If you do not solve the problem after checking these points, cut off the power
supply at the main electrical panel and contact customer service (consult our
Web site to obtain the phone numbers).

16 INSSTCNP5MA0612
5. Technical Specifications
Supply voltage:
120/208/240 VAC, 50/60 Hz

Maximum electrical current with a resistive load:

16 A
3840 W @ 240 VAC
3330 W @ 208 VAC
1920 W @ 120 VAC

Range of temperature:
0C to 35C (0F to 95F)

Temperature display resolution:

1C (1F)

Range of the temperature set points:

3C to 35C (37F to 95F)

Temperature set point increments:

1C (1F)

Storage:
-40C to 50C (-104F to 122F)

Certification:
cETLus

INSSTCNP5MA0612 17
 Limited Warranty
This unit has a 3 years warranty. If at any
time during this period the unit becomes
defective, return it to its place of purchase
with a copy of the invoice, or contact our
customer service department (with a copy
of the invoice in hand). In order for the
warranty to be valid, the unit must be
installed and used according to in-
structions. If the installer or the user modi-
fies the unit, they will be held responsible
for any damage resulting from this modifi-
cation. The warranty is limited to the factory
repair or the replacement of the unit, and
does not cover the cost of disconnection,
transport, and installation.

Customer service

Stelpro Design Inc.

1041, Parent Street
Saint-Bruno-de-Montarville (Quebec)
Canada J3V 6L7

Email: [email protected]
Web site: www.stelpro.com

18 INSSTCNP5MA0612
 www.stelpro.com

Users Guide
STCNP - 15mA
Smart non programmable electronic
thermostat for heating cable

(15mA Version) For further information or to consult this guide online,

please visit our Web site.
INSSTCNP15MA0612
 WARNING WARNING
Before installing and operating this product,
the owner and/or installer must read, under-
stand and follow these instructions and keep
them handy for future reference. If these in-
structions are not followed, the warranty will
be considered null and void and the manufac-
turer deems no further responsibility for this
product. Moreover, the following instruc-
tions must be adhered to in order to avoid
personal injuries or property damages,
serious injuries and potentially fatal elec-
tric shocks. All electric connections must be
made by a qualified electrician, according to
the electrical and building codes effective in
your region. Do NOT connect this product to
a supply source other than 120VAC, 208 VAC
or 240 VAC, and do not exceed the specified
load limits. Protect the heating system with
the appropriate circuit breaker or fuse. You
must regularly clean dirt accumulations on or
in the thermostat. Do NOT use fluid to clean
thermostat air vents. Do not install this ther-
mostat in a wet location such as a bathroom.
The 15mA model is not made for such an ap-
plication, as an alternative, please use the
5mA model.

2 INSSTCNP15MA0612
1. Description
The STCNP non programmable electronic thermostat can be
used to control heating floors with electrical current with a
resistive load ranging from 0 A to 16 A at 120/208/240 VAC.
It has an easy user interface. It keeps the temperature of a
room ( mode) and a floor ( mode) at a requested set
point with a high degree of accuracy.

Floor Mode (factory setting)

This control method is ideal in areas where you want a hot
floor at any time and when the temperature of the ambient air
can be high without causing discomfort.

Ambient Mode (you only have to press down the

A/F button to switch from one mode to the other)
This control method is ideal when you want a stable ambi-
ent air temperature (without fluctuation). Usually, this mode is
used in large and often occupied rooms where temperature
variations can be uncomfortable. For example, in a kitchen, a
living room or a bedroom.
Some factors cause variations in ambient air temperature.
They include large windows (heat losses or gains due to out-
side temperature) and other heat sources such as a central
heating system, a fireplace, etc. In all these cases, the
mode will ensure a uniform temperature.

This Thermostat is not compatible with the following

installations:
electrical current higher than 16 A with a resistive load
(3840 W @ 240 VAC, 3330 W @ 208 VAC and 1920 W @
120 VAC);
inductive load (presence of a contactor or relay);
central heating system.

INSSTCNP15MA0612 3
Parts supplied:
one (1) thermostat;
two (2) mounting screws;
four (4) solderless connectors suitable for copper wires;
one (1) floor sensor.

2. Installation

Thermostat selection and sensor location

The thermostat must be mounted on a connection box, at
around 1.5 m (5 feet) above the floor level, on a section of the
wall exempt from pipes or air ducts.
Do not install the thermostat in a location where temperature
measurements could be altered. For example:
close to a window, on an external wall, or close to a door
leading outside;
exposed directly to the light or heat of the Sun, a lamp, a
fireplace or any other heat source;
close or in front of an air outlet;
close to concealed ducts or a chimney;
in a location with poor air flow (e.g. behind a door), or with
frequent air drafts (e.g. head of stairs).
To install the sensor, refer to the installation guide of your
heating floor.

Thermostat mounting and connection

1. Cut off power supply on lead wires at the elec-
trical panel in order to avoid any risk of electric
shock. Ensure that the thermostat will be installed
on a junction box located in an uninsulated wall.
2. Ensure that the air vents of the thermostat are clean and
clear of any obstructions.
3. Using a screwdriver, loosen the screw retaining the mount-
ing base and front part of the thermostat. Remove the front
4 INSSTCNP15MA0612
 part of the thermostat from the mounting base by tilting it
upward.

4. Align and secure the mounting base to the connection box

using the two screws supplied.

5. Route wires coming from the wall through the hole of the
mounting base and make the required connections us-
ing the Four-wire installation figure, and using the sup-
plied solderless connectors. A pair of wires (black) must
be connected to the power source (120-208-240 VAC)
and another pair (yellow) must be connected to the heat-
ing cable (refer to the drawings displayed on the back of
the thermostat). For connections with aluminum wires, you

INSSTCNP15MA0612 5
 must use CO/ALR connectors. Please note that thermo-
stat wires do not have polarity, meaning that any wire can
be connected to the other. Then, connect the wires of the
floor temperature sensor at the indicated location behind
the thermostat.

Four-wire installation

6. Reinstall the front part of the thermostat on the mounting

base and tighten the screw at the bottom of the unit.
7. T urn on the power.
6 INSSTCNP15MA0612
8. Set the thermostat to the desired setting (see the follow-
ing section).

Ambient
temperature
(Ambient mode)

Floor
temperature
(Floor mode)

Security mode

Smart mode
Day mode
A/F TEST
Night mode

EGFPD button

Red Indicator
(EGFPD Test)

INSSTCNP15MA0612 7
3. Operation

First Start-up
At the first start-up, the thermostat is initially in the Day and
modes. The temperature is displayed in degrees Celsius
and the standard factory set point adjustment is 25C. The
maximum floor temperature is limited to 28C.

Maximum floor temperature limitation

At any time, the floor temperature (both in and modes)
is maintained at less than 28C (82F) in order to avoid over-
heating caused by an excessive heating request, which could
damage some materials or be detrimental for health.

Temperature set points

The figures beside the icon indicate the temperature set
points (both in and modes). They can be displayed in
degrees Celsius or Fahrenheit (see Display in degrees Cel-
sius/Fahrenheit).
Out of any adjustment mode, press down the + button to in-
crease the set point, or the - button to decrease it. Set points
can only be adjusted by increments of 1 degree. To quickly
scroll through the set point values, press and hold down the
button. Both in Manual and Smart modes, the mode set
points can range between 3 and 35C and can only be ad-
justed by increments of 1C (from 37 to 95F; by increments
of 1F from the Fahrenheit mode). From mode, the set
points can range between 3 and 28C (from 37 to 82F).
In Day mode, you can turn off the thermostat by lowering the
set point below 3C (37F). The set point value displayed will
be --, and heating system start up will be impossible.

Day mode and Night mode

8 INSSTCNP15MA0612
The thermostat includes a Day mode (Sun) and a Night mode
(Moon), both of them having their own independently adjust-
able and recorded set point. When switching from one mode
to the other, the system will automatically use the tempera-
ture set point corresponding to the Day/Night mode selected.
The and temperature are displayed by the figures un-
der the and icons, and the temperature set points are
displayed by the figures beside the icon, both in degrees
Celsius or Farenheit. The standard factory set point adjust-
ment is 25C for the Day/ mode (21C from the mode),
and 22C for the Night/ mode (18C from the mode).
In order to manually switch from one mode to the other,
simultaneously press down the + and - buttons and release
them immediately.

Night mode timer

The Night mode features a timer that automatically returns
to the Day mode after a selectable time period. This timer
allows the temporary use of a temperature set point. The
standard factory adjustment of the timer is 8 hours. With
this adjustment, the thermostat automatically returns to Day
mode 8 hours after being switched to the Night mode. You
can switch from the mode to the mode without affect-
ing the timer adjustment.
For example, if you want a night temperature lower than the
day temperature, both Day/Night modes set points will first
have to be set at the desired temperatures. Before bedtime,
the Night mode temperature set point will be activated by
switching manually to the Night mode. The timer is set for the
duration of the night. The thermostat will automatically return
to the Day mode at the end of the night, and the Day mode
temperature set point, which is higher, will become effective
at this time.

Night mode timer adjustment procedure

INSSTCNP15MA0612 9
1. First, switch to the Night mode by simultaneously pressing
down the + and - buttons and releasing them immediately.
2. From the Night mode, simultaneously press down the +
and - buttons for more than 3 seconds until the icon
starts to blink, indicating that the adjustment of the Night
mode timer is effective. The figures that replace the
mode temperature indicate the current adjustment of the
timer and hrs replaces the mode temperature.
3. If needed, adjust the timer by pressing down the + button
to increase the value, or the - button to decrease it. The
adjustment range is from 1 hour to 999 hours. To quickly
scroll through timer values, press and hold down the but-
ton.
4. When the adjustment is completed, release the buttons
and wait for 5 seconds to exit the adjustment function. The
thermostat will then return to the Night mode.
N.B. The Night mode timer will be automatically reinitialized
to the latest recorded value when switching from the
Day mode to the Night mode. It is not necessary to read-
just the timer every time you switch to the Night mode.
The timer is also reinitialized when this value is adjusted.
Once the timer has completed its cycle and when the
thermostat is in the Day mode, you must manually return
to the Night mode. If you want to automatically return
to the Night mode, the Smart mode must be selected.

Smart mode
The Smart mode, which is associated to the Night mode tim-
er, allows alternating between the Day/Night modes and the
two corresponding set points over a 24-hour period. Once
activated, this mode allows an automatic return to the Night
mode after 24 hours. The Smart mode allows you to define
two periods in a single day with different set points.
For example, if the Smart mode is activated and the Night
mode timer is set at 8 hours, the thermostat will be operat-
ing in the Night mode for 8 hours at the night temperature
set point. Then, it will return to the Day mode for 16 hours

10 INSSTCNP15MA0612
operating at the day temperature set point. At the end of the
24-hour cycle, the thermostat will return to the Night mode,
and the cycle will start again. The 24-hour cycle starts with
the Night mode as soon as the Smart mode is activated. The
Smart mode activation should be made when you want to
return to the Night mode. The normal course of a cycle in the
Smart mode is as follows:
1- Night mode: activated for the duration of the Night mode
timer cycle. It returns to the Day mode when the timer
cycle is completed.
2- Day mode: activated for the remaining time of the 24-hour
cycle. It returns to the Night mode at the end of the 24-
hour cycle.

Adjustment procedure of the Smart mode:

1. First, switch to the Night mode by simultaneously pressing
down the + and - buttons and releasing them immediately.
2. From the Night mode, simultaneously press down the +
and - buttons for more than 3 seconds, until the icon
starts to blink, indicating that the adjustment of the Night
mode timer is effective. The figures that replace the ambi-
ent temperature indicate the current timer adjustment. If
needed, adjust the timer by pressing down the + button to
increase the value, or the - button to decrease it. The Night
mode timer adjustment range is from 1 hour to 23 hours in
the Smart mode. To quickly scroll through the timer values,
press and hold down the button.
N.B. If you set the timer to any value exceeding 23 hours, it
will be impossible to activate the Smart mode and if it
was activated, the Smart mode will be deactivated.
3. Activate the Smart mode by simultaneously pressing down
the + and - buttons for at least 3 seconds. The icon will
appear. If the Smart mode was already activated, the same
procedure should be used to deactivate it.
4. When the adjustment is completed, release the buttons
and wait for 5 seconds to exit the adjustment function.
N.B. It is always possible to manually change the Day/Night
mode during a 24-hour cycle. In all cases, at the end of
INSSTCNP15MA0612 11
 the 24-hour cycle, the thermostat will return to the Night
mode and start a new cycle. It is thus not necessary
to readjust the Smart mode when a manual change is
made to the Day/Night mode. If the thermostat is set off
(--), the Smart mode will be deactivated.
When the power is restored after a power failure for example,
the Smart mode is deactivated and its corresponding icon is
blinking. The icon will stop to blink as soon as you will press
down a button.

Display in Degrees Celsius/Fahrenheit

The thermostat can display the ambient temperature and
the set point in degrees Celsius (standard factory setting) or
Fahrenheit.

Adjustment procedure for degrees Celsius/Fahrenheit dis-

play.
1. To switch from the degrees Celsius to the degrees Fahren-
heit, and conversely, the thermostat must be from the Day
mode. If so, simultaneously press down the + and - buttons
for more than 3 seconds until the icon blinks.
2. Press down the + button to switch from the degrees Cel-
sius to the degrees Fahrenheit, and conversely. The degree
Celsius or Fahrenheit symbol is displayed.
3. When the adjustment is completed, do not press down any
button during 5 seconds to exit the adjustment function.

/ Mode
To switch from the mode to the mode, or conversely,
press down the A/F button (when you are not in any adjustment
mode). Then, the temperature set point will become the same as
the or mode temperature, as applicable.

Safe Mode
If the thermostat fails to detect the presence of a floor
sensor, it will automatically revert to mode at a setpoint
of 21C. (with a maximum set point temperature of 24C)
12 INSSTCNP15MA0612
Sensor Selection
If you want to use the STCNP thermostat of Stelpro Design
with a temperature sensor already installed in the floor (other
than the sensor supplied with this thermostat), you must con-
tact the Stelpro Design customer service to validate the com-
patibility between the sensor and the thermostat. You must
know the serial number and name of the installed sensor.

Temperature Control
The thermostat controls the and temperature (accord-
ing to the / mode) with a high degree of accuracy. When
the heating starts or stops, it is normal to hear a clic sound.
It is the noise of the relay which opens or closes, as applicable.

Backlighting
The screen lights up when you press down a button. If you
do not press down any button for more than 15 seconds, the
screen turns off.
N.B. If you press down the + or - button once when the back-
light is off, it will light up without changing the set point
value. The set point value will change only if you press
down one of these buttons again.

Equipment Ground-fault Protection Device (EGFPD)

The thermostat has an integral Equipment Ground Fault Pro-
tection Device (EGFPD). It can detect a leakage current of
15mA. If a defect is detected, the EGFPD device lights up,
and both screen and heating system circuit are deactivated.
The EGFPD can be reinitialized either by pressing down the
Test button or by disconnecting the thermostat at the electri-
cal panel.

Equipment Ground-fault Protection Device (EGFPD) verification

INSSTCNP15MA0612 13
It is important to verify the EGFPD installation and operation
on a monthly basis.

EGFPD verification procedure

1- Increase the temperature set point until the heating power
bars are displayed (displayed in the bottom-right hand
corner of the screen).
2- Press down the Test button.
3- The following two cases can occur:
a) Successful test: The red indicator of the thermostat lights
up. In this case, press down once again the Test button to
reinitialize the EGFPD, the red indicator turns off.
b) Failed test: The red indicator does not light up and the
entire display blinks during 5 seconds. In this case, dis-
connect the heating system at the electrical panel and call
Stelpros customer service.

Security mode
This mode imposes a maximum temperature set point which
is impossible to exceed regardless of the mode in progress.
However, it is still possible to lower the set point at your
discretion. Please note that when the Security mode is acti-
vated, it is impossible to switch from the mode to the
mode, and conversely.
Procedures to activate Security mode
1. To activate the Security mode, the thermostat should be in
Day mode. Exit any adjustment mode to manually adjust
the set point at the desired maximum value.
2. 
Simultaneously press down the + and - buttons during
10 seconds (note that after 3 seconds, the icon starts
to blink and the software version and date are displayed.
Continue to press down these buttons).
3. After 10 seconds, the icon is displayed indicating that
the Security mode is activated. Then, release the buttons.
Procedures to deactivate Security mode

14 INSSTCNP15MA0612
1. To deactivate the Security mode, cut off the power supply
of the thermostat at the electrical panel and wait at least 20
seconds.
2. Restore the power supply to the thermostat. The icon
will blink during a maximum of 5 minutes, indicating that
you can deactivate the Security mode.
3. In Day mode, simultaneously press down the + and - but-
tons for more than 10 seconds. The icon will then be
hidden indicating that the Security mode is deactivated.
Parameter backup and power failures

The thermostat saves some parameters in its nonvolatile

memory in order to recoverer them when power is restored
(e.g. after a power failure). These are the four set points (Day/
Night/ / ), the Smart mode, the Security mode, the maxi-
mum set point of the Security mode, the Celsius/Fahrenheit
mode, the remaining time of the timer and the maximum floor
temperature. These parameters are saved every minutes
when a change occur, except for the Day/Night mode and
the remaining time of the timer, which are saved only if the
Smart mode was not activated.
Please note that the Smart mode is not automatically reacti-
vated when the power is restored, the icon blinks to in-
dicate that this mode was activated before the power failure
and that is now deactivated. Moreover, when the power is
restored, the Day/Night mode is recovered only if the Smart
mode was deactivated before. If not, the Day mode is auto-
matically reactivated. The Security mode is also reactivated if
it was activated before the failure. However, its icon blinks for
5 minutes and you can deactivate this mode by simultane-
ously pressing down the + and - buttons for 10 seconds. The
Security mode stays activated if you dont follow this process
and the icon stops blinking.

INSSTCNP15MA0612 15
4. Troubleshooting
Problem Solution
In normal operating conditions,
the thermostat housing can reach
The thermostat is hot. nearly 40C at maximum load. It
is normal and will not affect the
operation of the thermostat.
Check if the thermostat is properly
Heating is always on. connected. Refer to the installation
section.
Check if the thermostat is properly
Heating does not run even
connected and make sure the red
if the thermostat indicates
indicator is not lit. Refer to the
it is on.
installation section.
Check if the thermostat is properly
connected. Refer to the installation
The display does not come on.
section. Check the power supply at
the electrical panel.
The red indicator lights up
Contact customer service.
frequently.
Check the presence of an air
The displayed ambient stream or a heat source near
temperature is incorrect. the thermostat, and correct the
situation.
The display indicates E1*, Faulty thermal sensor. Contact
E2** or E3***. customer service.
Possibility of a bad contact. Check
Weak luminosity of the
thermostat wirings. Refer to the
display.
installation section.

* E1: Faulty ambient exterior sensor (open circuit) - written in the ambient section
** E2: Faulty interior sensor (open circuit) - written in the ambient section
*** E3: Faulty floor sensor (open circuit) - written in the floor section
N.B. If you do not solve the problem after checking these points, cut off the power
supply at the main electrical panel and contact customer service (consult our
Web site to obtain the phone numbers).

16 INSSTCNP15MA0612
5. Technical Specifications
Supply voltage:
120/208/240 VAC, 50/60 Hz

Maximum electrical current with a resistive load:

16 A
3840 W @ 240 VAC
3330 W @ 208 VAC
1920 W @ 120 VAC

Range of temperature:
0C to 35C 0F to 95F)

Temperature display resolution:

1C (1F)

Range of the temperature set points:

3C to 35C (37F to 95F)

Temperature set point increments:

1C (1F)

Storage:
-40C to 50C (-104F to 122F)

Certification:
cETLus

INSSTCNP15MA0612 17
 Limited Warranty
This unit has a 3 years warranty. If at any
time during this period the unit becomes
defective, return it to its place of purchase
with a copy of the invoice, or contact our
customer service department (with a copy
of the invoice in hand). In order for the
warranty to be valid, the unit must be
installed and used according to in-
structions. If the installer or the user modi-
fies the unit, they will be held responsible
for any damage resulting from this modifi-
cation. The warranty is limited to the factory
repair or the replacement of the unit, and
does not cover the cost of disconnection,
transport, and installation.

Customer service

Stelpro Design Inc.

1041, Parent Street
Saint-Bruno-de-Montarville (Quebec)
Canada J3V 6L7

Email: [email protected]
Web site: www.stelpro.com

18 INSSTCNP15MA0612