Project Spreadsheets to BS 8110 & EC2 The Concrete Centre

Client Advisory Group Made by Date Page

Location 32nd floor - corner panel F to G: 1 to 2 RMW 31-May-2017 174
2-WAY SPANNING INSITU CONCRETE SLABS to BS 8110:2005 (Table 3.14) Checked Revision Job No
Originated from RCC94.xls v4.1 2006 TCC chg - R68

DIMENSIONS MATERIALS STATUS VALID DESIGN

short span, lx m 9.00 fcu N/mm 40 c 1.50 F G
long span, ly m 9.01 fy N/mm 500 s 1.15 Edge 1
h mm 275 steel class A 1
Top cover mm 20 Density kN/m 23.6 Plan

Lx = 9 m
Btm cover mm 20 (Normal weight concrete)

Edge 4

Edge 2
LOADING characteristic EDGE CONDITIONS
Self weight kN/m 6.49 Edge 1 C C = Continuous
Extra dead kN/m 1.50 Edge 2 C D = Discontinuous Ly = 9.01 m
Total Dead, gk kN/m 7.99 f= 1.40 Edge 3 D
Imposed, qk kN/m 5.00 f= 1.60 Edge 4 C 2
Design load, n kN/m 19.19 See Figure 3.8 and clauses 3.5.3.5-6 Edge 3

SHORT LONG EDGE 1 EDGE 2 EDGE 3 EDGE 4 BS8110

MAIN STEEL SPAN x SPAN y Continuous Continuous Free Continuous Reference
s 0.030 0.028 0.040 0.037 0.000 0.037 Table 3.14
M kNm/m 46.1 42.7 61.5 57.0 0.0 57.0
d mm 247.0 231.0 249.0 235.0 249.0 235.0
k' 0.156 0.156 0.156 0.156 0.156 0.156
k 0.019 0.020 0.025 0.026 0.000 0.026
Z mm 234.7 219.5 236.6 223.3 236.6 223.3 3.4.4.4
As req mm/m 452 448 598 587 0 587
As min mm/m 358 358 358 358 358 358 Table 3.25
As deflection mm/m 489 485 ~ ~ ~ ~
mm 16 16 12 16 12 16
Layer B1 B2 T1 T2 T1 T2
@ mm 400 400 175 325 300 325
As prov mm/m 503 503 646 619 377 619
= % 0.204 0.218 0.260 0.263 0.151 0.263 %
S max mm 757 709 759 721 759 721 Clause
Subclause (a) (a) (a) (a) (a) (a) 3.12.11.2.7
DEFLECTION
fs 300 297 308 316 0 316 Eqn 8
Mod factor 1.442 Base ratio 26.0 Eqn 7

Perm L/d 37.50 Actual L/d 36.44 Asx enhanced 8.3% for deflection control Table 3.10

TORSION STEEL BOTH EDGES DISCONTINUOUS ONE EDGE DISCONTINUOUS
mm 10 X Y X Y
As req mm/m 358 358 3.5.3.5
As prov T mm/m 5000 5000 377 619
Additional As T req mm 0 0 0 0
As prov B mm/m 503 503 503 503
Bottom steel not curtailed in edge strips at free edges

SUPPORT REACTIONS (kN/m char uno) (See Figure 3.10) Sum vx = 0.614 Table 3.15

EDGE 1 EDGE 2 EDGE 3 EDGE 4 Sum vy = 0.720

1, F-G G, 2-1 2, F-G F, 2-1 equations

v 0.368 0.360 0.246 0.360 19 & 20

Dead kN/m 26.50 25.89 17.66 25.89

Imposed kN/m 16.58 16.20 11.05 16.20
Vs kN/m 63.6 62.2 42.4 62.2
OUTPUT/SUMMARY
SHORT LONG EDGE 1 EDGE 2 EDGE 3 EDGE 4
PROVIDE SPAN SPAN 1, F-G G, 2-1 2, F-G F, 2-1
MAIN STEEL H16 @ 400 B1 H16 @ 400 B2 H12 @ 175 T1 H16 @ 325 T2 H12 @ 300 T1 H16 @ 325 T2

ADDITIONAL CORNER 1 CORNER 2 CORNER 3 CORNER 4

TORSION STEEL F1 G1 G2 F2
X direction
placed in edge strips
Y direction

CHECKS BAR SINGLY MIN MAX GLOBAL

Lx > Ly < COVER REINFORCED SPACING SPACING DEFLECTION STATUS
OK OK OK OK OK OK VALID DESIGN
Project Spreadsheets to BS 8110 & EC2
Location 32nd floor - corner panel F to G: 1 to 2
2-WAY SPANNING INSITU CONCRETE SLABS to BS 8110:2005 (Table 3.14) Made by RMW Job No R68
Originated from RCC94.xls v4.1 2006 TCC Date 31-May-17

APPROXIMATE WEIGHT of REINFORCEMENT

SUPPORT WIDTHS GRIDLINE 1 G 2 F

(mm) WIDTH 300 300 300 300

TOP STEEL Type Dia Spacing No Length Unit wt Weight

Across grid 1 H 12 @ 175 50 2250 0.888 99.9
Across grid G H 16 @ 325 27 2275 1.578 96.9
Across grid 2 H 12 @ 300 30 2025 0.888 53.9
Across grid F H 16 @ 325 27 2275 1.578 96.9

Along grid 1 H 12 @ 300 7 5350 0.888 33.2

Along grid G H 12 @ 300 8 5800 0.888 41.2
Along grid 2 H 12 @ 300 6 5350 0.888 28.5
Along grid F H 12 @ 300 8 5800 0.888 41.2

Torsion bars H 10 0 0 0.617 0.0

BOTTOM STEEL
Short span - middle H 16 @ 400 17 7400 1.578 198.6
edges H 16 @ 400 6 9275 1.578 87.8
Long span - middle H 16 @ 400 17 7375 1.578 197.9
edges H 16 @ 400 6 9325 1.578 88.3

SUMMARY
Reinforcement density (kg/m) 47.0 Total reinforcement in bay (kg) 1064
Disclaimer
All advice or information from MPA-The Concrete Centre is intended for those who will evaluate the significance and limitations of its
contents and take responsibility for its use and application. No liability (including that for negligence) for any loss resulting from such advice
or information is accepted by MPA-The Concrete Centre or its subcontractors, suppliers or advisors. Users should note that all MPA-The
Concrete Centre software and publications are subject to revision from time to time and they should therefore ensure that they are in
possession of the latest version.

This spreadsheet should be used in compliance with the accompanying publication 'User Guide RC Spreadsheets: v4' available from The
Concrete Centre www.concretecentre.com/rcdesign Tel +44 (0)1276 606800

Status of spreadsheet This spreadsheet is shareware but may not be used for commercial purposes until the user has
Public release version. registered with The Concrete Centre using the licence validation form available on The Concrete
Centre website www.concretecentre.com/rcdesign

Revision history RCC94 Two-way Slabs (Tables)

Date Version Action Size (kB)

3-Oct-13 RCC94 v4.1 Selection of deflection base ratio clarified. 163
1-Apr-10 RCC94 v4.0 Re-badged as TCC/Mineral Products Association. 246
28-Jun-06 RCC94 v3.1 v3 release. Page nos, User Guide and registration details amended. 212
12-Nov-05 RCC94 v3.0 Updated to 2005 versions of BS8110 & BS8666 239
22-Jan-03 RCC94 v2.1 DETR logo replaced by DTI. 206
11-Oct-02 RCC94 v2.0 Version 2 enhancements 224
Orientation warning added at MAIN:Q21 (N Thomas)
22-Jun-00 RCC94 v1.3 136
Conditional formating Main!K10:P19 altered
8-Jun-00 RCC94 v1.2 MAIN:D34 etc corrected to include As min. 135
MAIN:F46 moved to correct position, MAIN:D64-D67 reformatted, continuity hatching
24-Mar-00 RCC94 v1.1 135
added to diagram.
First public release.
6-Aug-99 RCC94 v1.0 136
Includes b version comments