Introductory Information

Series Series ENG

Setup Guide Read this manual before attempting to operate the printer.
Keep this manual in a handy location for future reference.
Instructions in this Setup Guide show the iPF770 printer and printer stand ST-34. Note that your printer and printer stand may look
Introduction Caution different from these illustrations in some cases. However, basic operations are the same.

Overview of Setup Space Required for Installation

First, the stand needs to be assembled. A space larger than the following dimensions needs to be allocated when
Refer to the Stand Setup Guide included with the stand for details on how setting up this printer.
to assemble the stand.
Note that a stand is optional for the iPF670 series. 300mm
600mm
(When not using 10mm
the stand)
Preparations (P.2)
200mm 200mm
Install the Ink Tanks (P.3)

600mm
(When using the stand)
Install the Printhead (P.4)
Printer Stand used (*2) Installation space (W x D x H mm)
Without stand 1397 1308 807
iPF670 Series (*1) Stand ST-27 1397 1700 1362
Load Paper to Adjust the Printhead (P.5) Stand ST-26 1397 1480 1362
Stand ST-34 1704 1700 1362
iPF770 Series
Stand ST-33 1704 1480 1362
Install the Software (P.7) *1: A stand is optional for the iPF670 series. (It may be included as a
standard accessory in some locations.)
*2: The stands that are available differ between regions.

Store Accessories in the Pockets (P.13)

Package Contents
d c
How to Display the Electronic
Manuals (P.14) f
g i
Even if you do not use the printer driver, be sure to install Media
Configuration Tool from the provided User Software CD-ROM. With
Media Configuration Tool, the paper types that are available in your j
area can be registered to the printer. For instructions on installation, e
refer to "Install the Software" on page 7. (In Windows, select Install h
Individual Software in the Setup Menu window to install Media
Configuration Tool only.) b k
l a
Details for each step are given in this Setup Guide. Simply follow the instructions
to install the printer.
If an error message is displayed during setup or other problems occur, refer to
"Responding to Messages" on page 16.

The Manuals Supplied with This Printer

After installing the printer as shown in this Setup Guide, refer to the
manuals for instructions on operation and maintenance.
Printed Manuals
Quick Guide a. Printer g. Included paper
The Quick Guide contains information such as warnings for using this b. Roll holder: Already attached to printer h. Setup Guide (this document)
product safely and how to operate the navigation that is useful when c. 3-inch paper core attachment R i. Set of printer documentation
replacing paper, ink tanks, and the printhead. d. 3-inch paper core attachment L j. Set of CD-ROMs
e. Printhead k. Power cord
Electronic Manuals
f. Starter ink tanks (for first-time installation) l. Set of stands
Basic Guide C, M, Y, MBK x2, BK (iPF770 series only)
The Basic Guide describes the following information. A stand is optional for the iPF670 series. (It may be included as a standard
Loading paper, Replacing the consumables, Control Panel menus, and others MEMO accessory in some locations.)
Troubleshooting tips and Error messages Some items are included with the printer but not described in this manual.
Preparations for transferring the printer Keep these items in a safe place after setup because they are used in
various printing applications.
User's Guide
For instructions on the included items not described in this manual, refer to
This guide describes advanced usage of the printer such as paper saving tips, the User's Guide.
how to print a poster and banner with the supplied software and print quality A cable to connect the printer to a computer is not provided with the printer.
adjusting method, in addition to the basic instructions for printing on roll paper or
cut sheet. Canon, the Canon logo, and imagePROGRAF are trademarks or registered trademarks of CANON
INC.
Paper Reference Guide Microsoft is a registered trademark of Microsoft Corporation.
This guide describes about the types and specifications of the available media on Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other
countries.
the printer. Windows Vista is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or
other countries.
To refer to the electronic manuals Refer to "How to Display the Electronic Mac, Mac OS, OS X and Bonjour are trademarks of Apple Inc., registered in the U.S. and other
countries.
Manuals" (P.14) All other trademarks or registered trademarks described in this Setup Guide are the property of
their respective owners.

QT6-0555-V0 XXXXXXXX CANON INC. 204  PRINTED IN XXXXXXXX

QT60555V01
 Preparations Prepare the printer for use by assembling the stand and connecting the power cord.

1 2
Assemble the stand. Remove the packing materials from the top of the printer.

Refer to the Stand Setup Guide included with the stand for details
on how to assemble the stand.
Once you have finished, proceed to step 4.

A stand is optional for the iPF670 series. (It may be included as a

standard accessory in some locations.)
If you are using the iPF670 series without a stand, proceed to step
2.

3 4
Three people should hold the printer's carrying handles and place the printer on a table or Remove the orange tape used to secure
other flat location. the roll holder to the printer.

The iPF770 Series weighs approximately When moving the printer, firmly grasp the
Caution 53 kg and the iPF670 Series approximately carrying handles. Holding the printer at
43 kg by themselves. Moving the printer other positions is dangerous, and may
requires at least three people. Be careful to cause injury and damage if the printer is
avoid back strain and other injuries. dropped.

5
Move the printer to the location where you
will use it.

When moving the stand, lift the support rod

Caution to the position (a) before closing the output
stacker and unlocking the 4 casters. Failure
to do so may lead to scratched flooring,
When setting the printer down temporarily The way to set the printer down or to carry damage to the basket cloth, and injury.
make sure to put the printer on a flat, stable with the load only to the center of the
place. printer, may cause damage to the printer.
a

OFF

After you have moved the stand, be sure to

lock the 4 casters.

ON

6
Plug the power cord into the power supply
connector on the right of the printer and
plug the other end into the outlet.

2
 Install the Ink Tanks Install the 6 ink tanks.

1 2 3
Press the power button to turn on the When the following screen appears, use Select your local time zone and press OK.
printer. the and keys to select a language
and press OK.

Language Time Zone

English 0:London (GMT)
+1:Paris,Rome
Franais +2:Athens,Cairo
Data Data
Italiano +3:Moscow
Message Deutsch Message +4:Eerevan,Baku

Load FEED Cut Power

Menu Stop

Back Navigate

4 5 6
Instructions on ink tank installation While pressing the stopper of the ink tank Shake the ink tanks gently 1 to 2 times
are shown on the display screen. As lock lever inwards, open the ink tank lock before opening the pouch.
instructed, grab the handle on the ink tank lever upwards.
cover to open it.

Failure to shake ink tanks may result in

reduced print quality because ink ingredients
have settled on the bottom of the tank.
If the ink tank is cold, allow it to adjust to
room temperature before attaching it to the
printer.

7 8 9
Open the pouch and remove the ink tank. Insert the ink tank into the holder facing Close the ink tank lock lever until it clicks
as shown, with the ink holes down. into place. Make sure the ink lamp is lit in
At this time, detach and reattach the ink red.
tanks 2 to 3 times and ensure that the ink
tanks are security attached.

Never touch the ink holes (a) a

or metal contacts (b). Touching b
these parts may cause stains,
damage the ink tank, and affect
print quality.

Avoid dropping the ink tank after

removing it from the pouch.Otherwise,
ink may leak and cause stains.
If the ink tank does not fit in the holder,
Do not remove and shake ink tanks that make sure the color of the ink tank lock
have already been installed in the printer lever matches the color of the ink tank, and If the ink lamp is not lit, repeat steps 5 and
because ink may leak out. check the orientation of the ink tank. 9.

10 11
Repeat steps 5 to 9 to install all of the ink Close the ink tank cover.
tanks.


 Install the Printhead Next, install the printhead.

1
Open Upper Cover is shown on the
display screen. As instructed, open the top When installing the printhead, do not move the carriage (a) from the position shown in the
figure.
cover.
If you move the carriage (a), a warning noise sounds and the printhead cannot be installed.
If you have moved the carriage (a), close the top cover. The carriage (a) moves to the position
a shown in the figure.

Instructions on printhead attachment are

shown on the display screen.

2 3 4
Pull the printhead fixer lever forward all Lift the printhead fixer cover (a) to open it Hold the printhead by the grips (a) as you
the way to open it completely. fully. remove it from the pouch.
At this time, make sure that no debris
becomes adhere to the contacts (b) on the
carriage.

a
a

5
Remove the orange protective part (a). Insert the printhead into the carriage (b)

6
To remove orange protective part (b), Never touch the parts covered by the with the ink holes (a) facing away from the
protective part. This may damage the
push the grip (c) as you remove the part. printhead and affect printing quality.
printer as shown in the figure. Carefully
push the printhead firmly into the carriage
c The printhead contains ink. When
b
removing the protective material, it is
(b), ensuring that the part covered by
recommended that you do it over the the protective part does not touch the
bag that the printhead came in to avoid carriage.
a
spilling the ink and soiling your clothes or
the surrounding items.
a Do not reattach the protective part after
removing it. Dispose of these materials
according to local regulations. b

8 9
Pull the printhead fixer cover down toward
7
Push the printhead fixer lever all the way Close the top cover.
the front to lock the printhead in place. back.


 Load Paper to Adjust the Printhead

Load the included paper and adjust the printhead.

1
Select type of paper for printhead adj.
2 3
Slide the width guide (a) and align it Prepare one sheet of paper.
is shown on the display screen. Check with the mark for the size of paper to be Refer to the packaging for the paper to
that Cut Sheet is selected and press OK. loaded. In this example, align the width check which side is the printable surface.
guide with A2 to align it with the size of the
sample paper.

Return unused paper to the pouch it

came in, and store it away from heat,
humidity and direct sunlight.

Instructions on loading cut sheets are

shown on the display screen.

4 5 6
Load the sheet straight into the paper Adjust the position of the width guide (a) A message confirming paper advance is
feed slot with the printing-side facing up, to the size of the paper to be loaded. shown on the display screen. Press OK.
making sure the right edge is aligned with Make sure the width guide fits properly
the paper alignment guide (a) to the right against the edge of the paper to prevent it
of the roll cover. from being tilted or wrinkled.
Insert the paper until the leading edge
makes contact and you hear a tone.

Only one sheet can be loaded in the

printer. Do not load two or more sheets.
Doing so might cause a paper jam.
Wrinkled or warped paper might cause
paper jams. Be sure to flatten the paper
out before loading it.

7 8 9
The screen for selecting the paper type is When paper advance ends, the system When printhead adjustment ends, paper is
shown on the display screen. Press or is automatically filled with ink for the first printed with an adjustment pattern and is
to select the type of paper loaded in the time and printhead adjustment is started. ejected.
printer. It takes a total of about 20 minutes. While holding the paper, press the release
Select Coated Paper and press OK. Make use of this time by referring to lever (a) backwards to remove the paper.
Then from the menu that appears, select "Install the Software" on page 7 to install
Coated Paper and press OK. the software on your PC.

Charging the system with ink fills the system

MEMO from the ink tanks to the printhead. In
addition, cleaning is performed to keep the
printer in optimal condition. This may cause
a
the remaining ink indicator and maintenance
cartridge capacity indicator to drop some
amount. The starter ink tank is for first-time
installation. It is recommended that you
purchase replacement ink tanks quickly.

The paper is advanced.


10
Pull the release lever forward. The method for loading roll paper is given Follow the procedure below to display the
MEMO in the User's Guide, Basic Guide, and the navigation on how to load roll paper.
Printer setup is now complete. control panel navigation function, which can 1.Press Navigate.
be accessed using the procedure in "How to
Display the Electronic Manuals" (P.14).

2.Use the and keys to select Load Roll

Paper and press OK.
3.Use the and keys to select View Op.
Guide and press OK.
The navigation starts.


 Install the Software

Request for cooperation with quality improvement of Canon Large Format Printer
For development and marketing of products that better meet customer needs, Canon requests that you send information related to your Canon Large
Format Printer to Canon through the Internet. Check the content of the "Extended Survey Program" window that is displayed during the software
installation process. (See step 6 on page 7)

If you agree to our request, Canon requests that you approve to install the Canon Large Format Printer Extended Survey Program.
The Canon Large Format Printer Extended Survey Program automatically sends anonymous printer information on a periodic basis.
The Canon Large Format Printer Extended Survey Program does not send information unrelated to Canon Large Format Printer.
Canon does not send e-mail to you using the Canon Large Format Printer Extended Survey Program.
You can terminate automatic transmission of the Canon Large Format Printer Extended Survey Program at any time.
The automatic transmission can be terminated at any time.
If you have any questions about this program, please contact our customer support contact center.

Windows
You can print from Windows via USB or TCP/IP (network) connections.
The installation procedure varies depending on how your printer is connected. Install the software The following screen may be displayed
by following instructions below. If you connect the printer with a USB cable, refer to "For USB MEMO during installation depending on the
connections" on page 7. If you connect the printer with TCP/IP (network), refer to "For TCP/IP (network) security settings of your computer.
connections" on page 8.
Select Deactivate the block and click
Installation requires administrative rights (such as those of Administrator). Be sure to log on using Next.
an account with administrative rights before installation.

<Compatible Operating Systems>

32-bit: W
 indows 8.1, Windows 8, Windows 7, Windows Vista, Windows Server 2008, Windows
Server 2003 R2, Windows Server 2003, Windows XP
64-bit: W
 indows 8.1, Windows 8, Windows 7, Windows Vista, Windows Server 2012 R2, Windows
Server 2012, Windows Server 2008 R2, Windows Server 2008, Windows Server 2003 R2,
Windows Server 2003

For the Windows OS, use the latest version of Service Pack.
MEMO

For USB connections

Install the software

1 2
Use a USB cable that conforms to the After making sure the printer is not In the Setup Menu window, click Install
Hi-Speed USB specification. connected to the computer, turn the Printer Driver.
Connect the USB cable to the printer computer on. Insert the provided User
according to the on-screen instructions
Software CD-ROM for your operating
during installation of the printer driver.
If you connect the USB cable before system in the CD-ROM drive.
installing the printer driver, the printer
driver may not be installed correctly.

To choose a different language, click

MEMO Language.
You can view the basic operation of
the printer in the Basic Guide that is
contained on the CD-ROM by clicking
View Basic Guide.

3 4 5
Select the software to install in the In the Select Country or Region of Use After reading the license agreement, click
Installation List window, and then click window, select the country or region of Yes.
Next. use and click Next.
Point the mouse pointer at a software
name to display a summary of the
software.


6 7 8
If you can agree Extended Survey If you can respond to the questionnaire, Confirm your questionnaire responses,
Program, click Agree. click Next. and click Next.

9 10 11
In the Printer Selection window, select In the Printer Installation dialog box, When the following dialog box is
The printer is connected directly to a select Install with USB Connection, and displayed, make sure the printer is on and
computer and click Next. click Next. use the USB cable to connect the printer
to the computer.

If a warning message is displayed, click

MEMO Retry to try again.

12 13
After reviewing the installation results in In the Finish window, select Restart my
the Complete Installation window, click computer now and click Restart.
Next.

Be careful not to insert the USB cable When you restart the computer, the
into the LAN port. software settings are enabled. The
software installation is now completed.

For TCP/IP (network) connections

Install the software

2
If the printer is already connected to Make sure the printer is on.
the network, confirm the IP address Turn the computer on and insert the
assigned to the printer. Ask your provided User Software CD-ROM for your
network administrator for further
operating system in the CD-ROM drive.
information.

1
Use the LAN cable to connect the LAN port
on the back of the printer to the hub port.
Pass the network cable through the wiring
bracket (a).
If the printer is already connected to the
network, proceed to step 2.
a

3
Perform procedures of steps 2-8 on
If the printer is on, the Link indicator pages 7-8.
MEMO under the LAN port lights.
1000Base-T The LED on the bottom
connection lights green.
100Base-TX The LED on the top lights
connection orange.
10Base-T The LED on the top lights
connection green.


4 5
In the Printer Selection window, select
When searching the available printer on When entering the printer's IP address
The printer is connected to computers
the network manually
in a network and click Next.
After reading the precautions in the After reading the precautions in the Getting
Getting Ready window, select Find Ready window, select Specify the IP
available printers in the network and address of available printers in the
click Next. network and click Next.
Proceed to step 6. Proceed to step 8.

6
When searching the available printer on the network
Available printers are listed in the Search Results window.
Select a printer from the list on either their IPv4 Devices or IPv6 Devices The IPv6 Devices tab is not displayed in Windows XP, Windows
tabs and click Next. MEMO Server 2003 R2, and Windows Server 2003.
If the printer you want to use is not displayed in the list on the IPv6
Devices tab, connect via IPv4 instead.
If the printer you want to use is not displayed in the list of printers on
the IPv4 Devices tab, refer to "When the printer cannot be found on
the network" on page 10 to setup and configure an IP address for the
printer.

The following step differs depending on the IP Address Status of the

selected printer.
In the case of Not Set or IP Address Overlap, proceed to step 7.
In the case of Available, the installation begins. Proceed to step 9.

7 When searching the available printer on the network

In the Method of Configuring IP Addresses window, select the method of configuring the IP
address as suitable for your system.

To configure by directly entering the IP address

Select Configure manually in Method of Configuring IP Addresses and enter the IP address.

To have the IP addresses allocated automatically using the DHCP server function
Select Configure automatically. Note that other settings outside of the procedure are also
required. ("Using DHCP", P.10)

Once you have selected the method for configuring IP addresses, enter your preferred name for
the printer in Device Name and the installation location in Printer Location under Information
About Printer to Configure, and click Install to begin the installation.
Proceed to step 9.

8 9
When entering the printer's IP address manually After reviewing the installation results in
In the IP Address Specification window, the Complete Installation window, click
select either IPv4 Address or IPv6 Ask your network administrator for the Next.
IP address, as needed.
Address to enter the printer's IP address
and click Install.
The installation process begins. The IPv6 Devices tab is not displayed
MEMO in Windows XP, Windows Server 2003
R2, and Windows Server 2003.

10 11
In the Finish window, select Restart my When you restart the computer, the
computer now and click Restart. software settings are enabled. The
software installation is now completed.


 When the printer cannot be found on the network

1 2
If your printer cannot be found when connecting to On the tab selection screen of the control Use the and keys to select Interface
the network for the first time, setup an IP address panel, press the and keys to select Setup and press OK.

for the printer and then configure it on the printer. (settings/adj. tab) and press OK.

When ink fills the system for the first time, after
printhead adjustment is finished, specify the IP

3
Use the and keys to select TCP/IP
address on the printer's control panel. No Paper Loaded and press OK.
OK:Setting/Adj. Menu
When ink fills the system for the first Maint.C Remain.: 80%
time, do not operate the printer until Tot.Print Area(m2):
printhead adjustment is finished.
678

4 5
Enter the IP address. Navigate through Press Menu.
How to enter IP addresses
the following menus using the and 1. Press the and keys to select a

MEMO
keys on the control panel. field for inputting values.
2. Use the and keys to input values.
1.Select IPv4 and press OK.
Pressing increases the value by

6
one. On the registration confirmation message
2.Select IPv4 Settings and press OK. that appears, select Yes using the and
Pressing decreases the value by
one. keys, and then press OK.
3.Select IP Address and press OK. The IP address is set on the printer.
Holding down either the or keys
continually increases or decreases Next, restart installation of the printer
4.Enter the IP address. driver.
the value.
3. Press OK once you have finished.

7
In the Search Results window, select
If the following screen appears, click
Specify the IP address of available Retry and select Specify the IP
MEMO
printers in the network and click Next. address of available printers in
When the IP Address Specifications the network on the next screen that
window appears, follow the instructions of appears.
"When entering the printer's IP address
manually" in step 8 to 11 on page 9 to
complete the installation of the software.

Using DHCP

1
To use the DHCP server function to automatically This section describes how to turn on DNS Perform steps 1 to 3 of the procedure in
allocate an IP address to the printer, one of the dynamic update from the control panel of the "When the printer cannot be found on the
following settings needs to be configured. Check printer. network" on page 10.
with your network administrator for the settings
that match your system.

2
The DNS dynamic update function can Select IPv4 or IPv6 using the and
When used in an environment with a DNS MEMO also be configured using Remote UI. keys and then press OK.
server Refer to "Configuring the Printer's TCP/
Configure the DNS dynamic update function in IP Network Settings With RemoteUI" in
the user guide for details.
the printer and register the printer DNS host name

3
Select DNS Settings using the and
with the DNS server. keys and then press OK.
When used in an environment without a DNS
server

4
Select DNS Dync update using the
Configure the DHCP server to always allocate the and keys and then press OK.
same IP address to the printer.

5 For IPv4 For IPv6

Select On using the and keys and 1. When Use the same host name and
then press OK. domain name as IPv4? is displayed,
select Off using the and keys and
then press OK.
2. Select Statefull Addr using the and
keys and then press OK, and then
select On using the and keys and
then press OK.
3. Set Stateless Addr to On using the
same procedure as in Step 2.

10
 Mac OS
You can print from Mac OS via USB or network connections such as Bonjour or IP.
Install the software depending on your computer environment.

<Compatible Operating Systems>

OS X v10.6.8 to v10.9

Install the software

1 2
If you install the software, log onto the After making sure the printer is not On the desktop, double-click the CD-ROM
computer as an administrator. connected to the computer, turn the icon and then the iPF Printer Setup icon.
computer on. Insert the provided User
Software CD-ROM for your operating
system in the CD-ROM drive.

User Software

3 4 5
Click Next. If a screen requesting the name and Select the country or region where you
password is displayed, enter the user are using the printer, and click Next.
name and password of a user with
administrative rights and click OK (or
Install Helper on OS X v10.7 or later).

6 7 8
Select the software to install and click After reading the software license If you can agree Extended Survey
Next. agreement, click Yes. Program, click Agree.
Move the mouse pointer near the name of
the software to display an overview of the
software.

9 10 11
If you can respond to the questionnaire, Confirm your questionnaire responses, The progress of the installation is
click Next. and click Next. displayed.
Once all of the installation has finished,
the screen automatically advances to the
setup screen.

Connect the printer to a computer

12 When the following screen is displayed, make sure that the printer is on, and then connect the printer to the computer or the network with a cable.
When connecting to a network, pass the network cable through the wiring bracket (a).
For USB connections For network connections

Be careful not to insert the USB cable into the LAN port.
MEMO

11
Select the printer

13 14 15
Select the method of connecting to the Click Add Printer. Select the printer to add from Default and
printer, and click Next. click Add.
For USB connection, the printer is
automatically added and you should
proceed to step 17.

You can view a description of adding

MEMO printers by clicking Help. It may take a long time until the printer
MEMO information is displayed on the screen.
You can also add the printer by
specifying the IP address by selecting
IP.

16 17 18
Click Next. Select the Execute media type update Click OK.
check box and click Next.

If the same model of printer is already

MEMO registered on the computer, a screen is
displayed for printer selection. Select
the desired printer and click Next.

19 Click Exit.
The following screen is displayed while
the media information is being updated.
Do not perform any other operations.
When the media information has
been updated, the screen is no longer
displayed.

12
 Store Accessories in the Pockets

1 2
Use the manual pocket to store the manual so you can refer to it When using the stand, store the 3-inch paper core attachment and
as needed. other accessories in the accessory pocket.

The accessory pocket is included with the stand.

MEMO

13
 How to Display the Electronic Manuals
The electronic manuals for this printer are the User's Guide, Paper Reference Guide, and Basic Guide. For details on the content of each manual,
refer to "The Manuals Supplied with This Printer" on P. 1.

Viewing the User's Guide and Paper Reference Guide

The User's Guide and Paper Reference Guide are not included with the printer. You can view each of the manuals on the Web from the links in the installed
software by using the following procedure. An Internet connection is required in order to view the manuals.

On Windows

This section describes how to view the User's Guide and Paper Reference You can also view each of the manuals by clicking the links to the
Guide from the printer driver. MEMO product manuals from other installed software.

1 On Windows 7 and earlier

Click the Control Panel from the desktop Start menu.

On Windows 8 and later

1. If the Start screen is displayed, click the 2. Move the mouse pointer upwards from 3. Click the Settings button and then Control
Desktop tile to display the desktop. the bottom right corner of the desktop to Panel.
display the charms (a).

2 Click Hardware and Sound (or Printer

and Other Hardware). 3 Click Devices and Printers (or Printers
or Printers and Faxes). 4 Right-click the printer and then click
Printer Properties (or Properties).

5 Click Preferences (or Printing

Preferences) to open the Printing
Preferences dialog box that has the
6 Select the Support sheet and click the
User Manual button. 7 To display the user guide, click User's
Guide.
To display the Paper Reference Guide,
name of the printer in the title. click Paper Reference Guide.

On Mac OS

1 2
This section describes how to view the User's Click the System Preferences icon in the Click Print & Scan. (This is identified as
Guide and Paper Reference Guide from the Dock. Printers & Scanners or Print & Fax in
Printmonitor that is installed with the printer other versions of Mac OS.)
driver.

You can also view each of the manuals

MEMO by clicking the links to the product
manuals from other installed software.

14
 3 Select the printer from the list of printers
and click Options & Supplies. 4 Click Utility.
5 Click Open Printer Utility.

6 Click Support.
7 Click the User Manual button.
8 To display the user guide, click User's
Guide.
To display the Paper Reference Guide,
click Paper Reference Guide.

Viewing the Basic Guide

The Basic Guide is stored on the User Software CD-ROM that is included with the printer. Use the following procedure to view it.

On Windows

1 Load the User Software CD-ROM into the

CD-ROM drive of the computer. 2 Click View Basic Guide in the Setup
Menu window. 3 Open the PDF file that is contained in the
folder that opens.

The Basic Guide is displayed.

On Mac OS

1 Load the User Software CD-ROM into the

CD-ROM drive of the computer. 2 Double-click the CD-ROM on the Desktop
and then the iPF Printer Setup icon. 3 Click Basic Guide.

4 Open the PDF file that is contained in the

folder that opens.

The Basic Guide is displayed.

15
 Responding to Messages
Error messages may appear on the display screen of the control panel during printer installation in some cases. If so, it may not indicate a problem with
the printer, and the issue may be easily resolved. Common messages and the causes are listed here with corrective actions. For more information on other
messages, refer to the User's Guide or Basic Guide. (See "How to Display the Electronic Manuals" on P.14)

Message Cause Corrective Action

Check if ink tank is set, and its color and There is no ink tank of the indicated color in Load or reload the ink tank.
direction. the printer. (see steps 4-11 on page 3)
Cannot recognize print head. Open the top The printhead is not installed. Install the printhead.
cover and re-insert the printhead. (see steps 1-9 on page 4)
Paper is crooked. The loaded paper is crooked. 1. Press the release lever backwards.
Push the release lever back, then 2. Pull out the paper.
Pull out the cut sheet. 3. Pull the release lever forward.
Could not detect paper size. Push release The paper is loaded in the wrong position or 4. Load or reload the paper.
lever back, the paper is curled.
Pull out the cut sheet.
Insert the maintenance cartridge. The maintenance cartridge is removed. Install the maintenance cartridge correctly.
Hardware error. The ink tank is not installed correctly. Turn off the power, remove and then reinstall all of the ink tanks, and then
03130031-2F7x turn on the power. (See steps 4-5 and 8-11 on page 3)
(where x is 0, 1, or 2) If the same message is displayed again, write down the error code and
message, turn off the printer, and contact your Canon dealer for assistance.
Hardware error. Another kind of error has occurred. Turn off the printer and wait at least three seconds before restoring
xxxxxxxx-xxxx the power. If the message still appears, write down the error code and
(x represents a letter or number) message, turn off the printer, and contact your Canon dealer for assistance.
ERROR Exxx-xxxx You may have encountered an error that Write down the error code and message, turn off the printer, and contact
(x represents a letter or number) cannot be resolved. your Canon dealer for assistance.

16