Scribd
Upload
81 views7 pages

PSA Lab - Exp 10 - Filled

1. The document describes an experiment involving modeling different configurations of three-phase transformers in MATLAB/Simulink to analyze zero-sequence current flow. 2. Five cases are examined: a YY transformer with both sides grounded, a YY transformer with the primary grounded and secondary ungrounded, a ΔΔ transformer, a YΔ transformer with the Y side ungrounded, and a YΔ transformer with the Y side grounded. 3. For each case, the document records the zero-sequence currents entering and leaving the transformer, sketches the equivalent zero-sequence circuit, and may derive the zero-sequence impedance.

Uploaded by

Sumra Maqbool
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
81 views7 pages

PSA Lab - Exp 10 - Filled

1. The document describes an experiment involving modeling different configurations of three-phase transformers in MATLAB/Simulink to analyze zero-sequence current flow. 2. Five cases are examined: a YY transformer with both sides grounded, a YY transformer with the primary grounded and secondary ungrounded, a ΔΔ transformer, a YΔ transformer with the Y side ungrounded, and a YΔ transformer with the Y side grounded. 3. For each case, the document records the zero-sequence currents entering and leaving the transformer, sketches the equivalent zero-sequence circuit, and may derive the zero-sequence impedance.

Uploaded by

Sumra Maqbool
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

1

Reg. # 2012-EE-402 | 2012-EE-404


Marks
EXPERIMENT # 10

Sequence Circuits of Three Phase Transformers


Objectives:
To learn about zero-sequence current flow in three phase transformer topologies.

Lab Tasks:

1. Simulate the circuit shown in MATLAB / Simulink.


2. Build the three phase transformer using individual single phase transformers (with 1:1
ratio) with neutral resistance of 0.1 . For transformer parameters, use SI units with R =
0.1 and L = 1 mH.
3. Use different topologies of three phase transformer for the given circuit and find out
about zero sequence current flow.

Diagram:

Van = 200 / 0 Vbn = 250 / 250 Vcn = 175 / 100

Ra = Rb = Rc = 1
2

Case 1: YY transformer; both sides grounded

1. Determine zero sequence current entering and leaving the transformer using zero
sequence measurement blocks.

I(0)primary = Ip(0) = 25.92 /-55.89o A I(0)secondary = Is(0) = 25.92/-55.89 o A


2. Determine zero sequence impedance of this transformer. To do this, measure zero
sequence voltages on both sides of the transformer.

V(0)primary = Vp(0) = 49.42/-36.65 o V V(0)secondary = Vs(0) = 25.92/-55.89 o V

V (0) (0)
p V s
Z0= = 0.8+0.628i = 1.017/38.139
I (0)
p

3. Derive Z0 from Z0 = Z + 3ZN + 3(N1/N2)2 Zn.

Z = Leakage impedance of transformer (Primary as well as Secondary referred to primary side)


Z = 2.{ (0.1)+(2 . pi .50 . 1x10-3)i }
Z0 = Z +3(0.1)+3(1)(0.1)
Z0 = 1.017 /38.14o
4. Sketch zero sequence circuit of this transformer.
3

Case 2: YY transformer; Primary side grounded; Secondary ungrounded

1. Determine zero sequence current entering and leaving the transformer using zero
sequence measurement blocks.

Ip(0) = 7.145x10-5/-88.85 o A Is(0) = 3.64x10-11/-89.65 o A

2. Sketch zero sequence circuit of this transformer.


4

Case 3: transformer

1. Determine zero sequence current entering and leaving the transformer using zero
sequence measurement blocks.

Ip(0) = 2.109x10-11/76.47 o A Is(0) = 4.67x10-12/-144.5 o A

2. Sketch zero sequence circuit of this transformer.


5

Case 4: Y transformer; Y ungrounded.

1. Determine zero sequence current entering and leaving the transformer using zero
sequence measurement blocks.

Ip(0) = 5.22x10-12/24.43 o A Is(0) = 1.372x10-11/127.3 o A


6

2. Sketch zero sequence circuit of this transformer.

Case 5: Y transformer; Y grounded

Determine zero sequence current entering and leaving the transformer using zero
sequence measurement blocks. Make the currents equal.
Ip(0) = 61.55/-88.14 o A Is(0) = 2.484x10-11/171.1 o A

Determine zero sequence impedance of this transformer

Vp(0) = 49.42 /-36.65 o V Vs(0) = 1.372x10-11 /127.3 o V


7

(0) (0)
V p V s
Z0= = 0.8029 /51.49o
I (0)
p

Derive Z0 from calculations.

Z0 = Z + 3ZN
Z = 2.{ (0.1)+(2 . pi .50 . 1x10-3)i }
Z0 = Z +3(0.1)
Z0 = 0.8029 /51.48o

Sketch zero sequence circuit of this transformer.

Learnings/Comments:

You might also like