Transformer Notes PDF

EMF Equation of a Transformer
In a transformer, source of alternating current is applied to the primary winding. Due to this, the current in the
primary winding (called as magnetizing current) produces alternating flux in the core of transformer. This
alternating flux gets linked with the secondary winding, and because of the phenomenon of mutual
induction an emf gets induced in the secondary winding. Magnitude of this induced emf can be found by using
the following EMF equation of the transformer.
Let,
N1 =Number of turns in primary winding
N2 = Number of turns in secondary winding
m = Maximum flux in the core (in Wb) = (Bm x A)
f = frequency of the AC supply (in Hz)
As, shown in the fig., the flux rises sinusoidally to its maximum value m from 0. It reaches to the maximum
value in one quarter of the cycle i.e in T/4 sec (where, T is time period of the sin wave of the supply = 1/f).
Therefore,
Average rate of change of flux = m /(T/4) = m /(1/4f)
Therefore,
average rate of change of flux = 4f m ....... (Wb/s).
Now,
Induced emf per turn = rate of change of flux per turn
Therefore, average emf per turn = 4f m ..........(Volts).

Now, we know, Form factor = RMS value / average value =1.11 for sine wave
Therefore, RMS value of emf per turn = Form factor * average emf per turn.
Therefore, RMS value of emf per turn = 1.11 x 4f m = 4.44f m.
RMS value of induced emf in whole primary winding (E1) = RMS value of emf per turn X Number of turns in
primary winding
E1 = 4.44f N1 m
Similarly, RMS induced emf in secondary winding (E2) can be given as
E2 = 4.44f N2 m.
RATIOS OF A TRANSFORMER
-
DC SUPPLY FOR A TRANSFORMER
PRACTICAL TRANSFORMER
We had earlier described an ideal transformer where many assumptions were made in order to understand
the basic working of the transformer. We will now discuss the features of the practical transformer and
consider all the non-idealities.
i) Effect of winding resistance:
ii) Iron Loss: As the core the transformer is subjected to alternating flux, eddy current loss and
hysteresis loss occur in the core. These two losses together are termed iron loss or core loss.
These depend on the maximum value of the flux density in the core, the supply frequency,
volume of core which are all constant. Hence, iron losses may be considered as constant
losses in a transformer
iii) Effect of leakage flux:

Equivalent circuit of transformer
Practical Transformer on no-load
In a practical transformer, iron core causes hysteresis and eddy curent losses as it is subjected to alternating
flux. In the no-load condition, the primary current drawn from the supply, denoted as Io, has to supply these
iron losses as well. As the value of Io is very small, the primary copper losses are negligible. The no-load input
current Io therefore has two components,
i. A purely reactive component, Im, called magnetizing component of no-load current required to
produce flux.
ii. An active component, Ic or Iw, which supplies total losses under no-load condition(iron loss) called
core loss component of no-load current.
Flux in the core of a transformer
For a transformer,
E1 = 4.44f N1 m or E2 = 4.44f N2 m
The primary voltage and frequency remain constant. Hence, for a transformer, the flux in the core remains
constant and independent of the load.
Losses in a transformer
EFFICIENCY OF A TRANSFORMER
Secondary current I2 varies with load proportionately.
I2 at load = ( I2)FL
As voltage is constant, the KVA rating also varies proportionately with load
KVA rating at load = (full-load KVA rating)
Copper loss, Wcu (I2 )2 ,
Wcu at any load = ( )2 ( Wcu)FL
Iron losses are constant losses and hence do not depend on the load.
Efficiency can calculated using the following equation:
( )
( )
condition for maximum efficiency of a transformer
When a transformer works on a constant input voltage and frequency, its efficiency varies with the load. As
the load increases, efficiency increases. At a certain load current, it achieves a maximum value of efficiency. If
the transformer is loaded further, the efficiency starts decreasing. The load current at which efficiency is
maximum is denoted as I2m and the maximum efficiency is denotes as max
Therefore, Condition for maximum efficiency is Iron loss= copper loss
Load current I2m at maximum efficiency
KVA supplied at maximum efficiency

Transformer Notes PDF

Uploaded by

Copyright:

Available Formats

Transformer Notes PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Transformer Notes PDF

Uploaded by

Copyright:

Available Formats

EMF Equation of a Transformer

Average rate of change of flux = m /(T/4) = m /(1/4f)

Therefore, average emf per turn = 4f m ..........(Volts).

Therefore, RMS value of emf per turn = 1.11 x 4f m = 4.44f m.

Similarly, RMS induced emf in secondary winding (E2) can be given as

i) Effect of winding resistance:

iii) Effect of leakage flux:

Practical Transformer on no-load

KVA rating at load = (full-load KVA rating)

Copper loss, Wcu (I2 )2 ,

Wcu at any load = ( )2 ( Wcu)FL

Efficiency can calculated using the following equation:

condition for maximum efficiency of a transformer

KVA supplied at maximum efficiency

You might also like