[email protected] | www.bmp-group.

com

ADVANTAGES OF STEEL IN NON-LOAD BEARING WALLS

FAST Installs in the time! Pre-punched for wiring. SAFETY 100% Non-combustible. No pesticides or toxins are
required to protect steel framing
EASY Lightweight studs snap and lock into place ECONOMICAL One of the most economical from termites or vermin.
quickly with easy clean up No saw dust! ways to frame your basement.
Easy to transport and handle. No emissions from resins,
SOUND Better room-to-room adhesives or chemicals normally
DURABLE Will not rot, support mould, or feed insects sound control. used for wood construction
and vermin. occurs with steel.

QUALITY Consistent dimensions, manufactured ENVIRONMENTALLY 100% recyclable. In 2003, the Asthma Society
precision in every piece. FRIENDLY of Canada recognized that
steel framing, made with
WALLS STAY No warping, shrinking, twisting or nail pops! POLLUTION Steel resists mould spores that certified steel, is part of a
healthy indoor air environment.
STRAIGHT CONTROL can lead to chronic illness.

ESTIMATION GUIDE Steel Stud Steel Stud Steel Stud

FRAMING A BASEMENT?
3-5 8 2-1 2 1-5 8

Steel Stud Steel Stud Steel Stud Wood Wood Wood

3-5 8 2-1 2 1-5 8 2x4 2x3 2x2

Bailey Steel Studs are basically the same dimensionally as wood studs.
Measure your project and make a drawing (floor plan) with dimensions showing E
walls, ceiling joists, window bulkheads, columns, stairwells, beams, doorways,
electrical outlets and switches. Your material supplier can assist you with code I D
requirements, material estimating and ordering. G K
Steel Stud Application F
Bailey Studs are C shaped channels installed vertically, usually
16 inches on centre. Flanges securely grab screws and factory made C
holes simplify installation of wiring and piping services. Use 3 5/8 or
2 1/2 studs for wall framing and 1 5/8 studs for framing around A
columns and bulkheads. H
B
Steel Stud Quantity J
Allow one (1) piece of stud for every lineal foot of wall. This covers
typical studs plus extras required at corners and doors. Please refer to
door and window manufacturers installation instructions for rough NON LOAD BEARING
Bailey Steel Stud A STEEL STUD
opening sizes.

Steel Track Application

D-700 ANGLE
Bailey Tracks are U shaped channels installed to ceilings and floors to hold studs G
in place. Tracks may also be used to make door and
window headers and sills. Bailey tracks feature 1 5/8, 2 1/2, 3 5/8, 6
snug fit for studs and continuous stiffening ribs
along their flanges, for added strength. NON LOAD BEARING
Bailey Steel Track B STEEL TRACK
Steel Track Quantity 1 X 2 X 10 - 90
Allow (2) lineal feet of track for every lineal foot of wall plus 10% extra for cuts.
Allow extra track for each door header, window header and window sill. D-100 1 1/4 CORNERBEAD
H
GYPSUM DRYWALL BOARD is typically 4 foot x 8 foot with longer panels 1 5/8, 2 1/2, 3 5/8, 6
available. Allow one (1) panel for every 4 foot length of 8 foot high wall plus
1 1/2 CHANNEL 12
5% to 10% extra. Please refer to suppliers recommendations. C NOTE: Bridging channel must be used
DRYWALL TAPE AND JOINT COMPOUND usage for 40 feet of 8 foot high wall in conjunction with BX wiring.
7, 8, 9, 10, 12 - 90 OR 130
is approximately 100 feet (30 meters) of tape and 44 lbs. (20 kg) of compound.
Please refer to suppliers recommendations. D-400 J TRIM
TOOLS REQUIRED for framing include a tape measure, sheet metal snips,
I
plumb-bob, level, square, reversible screw gun or drill and C-clamps.
Additional tools required for drywall include a utility knife, joint finishing knives,
drywall hole saw, and a square. D-1007 RESILIENT
D CHANNEL 12
FASTENERS Application Quantity 1/2 OR 5/8 X 10

1 1/4 Drywall Ceiling Track to Joists 30 to 40 screws D-200 L TRIM ANGLE

Screw Floor Track to Wood Floor required per 4 x 8 J
Gypsum Board to Wall Framing gypsum board
Gypsum Board to Ceiling Framing
Corner Bead to Gypsum Board
D-1001
Concrete Floor Track to Concrete Floor 1 every 2 ft. + E FURRING CHANNEL 12
Fastener OR 10%
Nail Drive 1/2 OR 5/8 X 10
Anchor
U FLEX TRACK
K
9/16 Wafer Track to Stud 4 per stud or
Head Framing 2 per stud against
Screw OR exterior walls
7/16 Pan GROMMETS &
Head Framing F ELECTRICAL BOX
Screw
2 1/2 OR 3 5/8 X 8
Trim Head Casing and Base Trim to Studs 1 per ft
Screw and Tracks

CSA APPROVED

MONTREAL TORONTO CALGARY EDMONTON VANCOUVER

Tel. 800-263-3455 Tel. 800-668-2154 Tel. 800-665-2013 Tel. 800-563-1751 Tel. 800-818-2666
 DISTRIBUTED BY:

INSTALLATION STEPS IMPORTANT DETAILS

SAFETY FIRST: STEEL EDGES CAN BE SHARP, SO PLEASE BE CAREFUL.
ALWAYS FOLLOW GOOD SAFETY PRACTICES INCLUDING WEARING
WORK GLOVES AND SAFETY GLASSES. CONSULT WITH MATERIAL
SUPPLIER ON CODE REQUIREMENTS.

Preparation
LOCATE WALL PARTITIONS according to your drawing and mark positions INTERSECTION INSIDE CORNER OUTSIDE CORNER
of track at floor and ceiling. Check alignment with a plumb bob. Omit bottom
Install track on the floor and Install tracks on the floors Install tracks on the floors and
tracks at door openings. Before working on existing basement walls ensure
ceiling. Leave 1/2 or 5/8 gap and ceilings 90 to each other ceilings perpendicular to each other.
they are dry. Cover all concrete walls with tarpaper.
for drywall to run through. leaving 1/2 or 5/8 gap for Three studs are required to
drywall to run through.
Installing Track Place the intersecting stud
centred with adjoining stud Form right angle with studs to
complete an outside corner.
P lace one stud at outside edge
INSTALL TRACK AT CEILING by measuring and secure with a drywall create inside corner. of track intersection and two on
and cutting to length then securing to ceiling screw (as shown). either side of inside intersection.
joists with 1 1/4 screws. Where track runs
parallel to and between ceiling joists, make a
cross member from a track piece and install
Bailey Track between joists every 24 inches and fasten
ceiling track to them.
Make Cross Member
from Track
INSTALL TRACK AT FLOOR by measuring and
cutting to length and secure to floor every
24 inches and 2 inches from cut ends. Please DOOR FRAME A DOOR FRAME B TRIM
see the important details section for the
Install double steel studs at the Install frame using one wood and F asten trim to base of wall with
how-tos of installing inside corners, outside door frame. one steel stud as shown. trimhead screws.
corners, and an intersection.
Ensure studs are facing each Butt steel stud against wood stud C
 onstruction adhesive can also be
Bailey Track Make sure that there is a 1/4 space between other as shown above. and fasten both to drywall. applied to the back of trim prior
the tracks and concrete wall and the bottom Secure each stud using drywall to fastening.
and top tracks are aligned. screws.

Cross Member

Building the Walls Ceiling Joists

INSTALL THE STUDS by trimming the studs 1/2 shorter than the distance Wire
between the top and bottom tracks to allow for movement of the structure
above. Spacing studs 16 inches on centre ensuring all flanges face the same
direction. Twist studs into tracks for friction fit and using a level make sure (A) Stud Splice
they are straight. Connect studs to tracks using framing screws. For partition
walls that need strengthening use reinforcing channel (See Picture C on front). Electrical Details
Please see the important details section for the how tos of installing inside INSTALL CSA APPROVED grommets, electrical boxes and stand-offs. Plastic grommets (A) are
corners, outside corners, and an intersection. installed into pre-punched holes in studs to allow for non-metallic sheathed wiring to run
through to electrical outlets.
Check plumb with
level or plumb bob
Flanges facing
same direction Levelling Ceilings 2 3/4

INSTALL BAILEY D-1001 FURRING 1 1/2

CHANNELS where desired. Ideal for
furring out and around exposed 7/8
16 O.C
services. Install perpendicular to
1 3/8
joist in rows spaced 16 or 24 on
centre and within 6 of perimeter.

Framing Door & Window Openings

ON EITHER SIDE OF THE DOORWAY EDGE, place Quieter living at no extra cost!
two studs face to face (See important details for two INSTALL BAILEY RC PLUS RESILIENT CHANNEL to improve the reduction of room to room sound
versions). Cut track the width of the opening and allow transmission obtaining a STC 51 or greater. Install RC Plus perpendicular to framing in rows
6-8 extra to attach as header to the studs. Cut and spaced 16 or 24 on centre and within 6 of perimeters. Install to one side of wall framing and
bend pieces of track as shown to make header and sill to underside of ceiling joists. Seal openings to prevent sound leaks. Ensure that screws used to
Double studs at members. Reinforce the header with center stud and attach gypsum panels to resilient channels do not touch the framing.
door and window secure to stud with screws.
openings wider
than stud spacing Cut
ing Bend Ceiling
Open
Bend
4-6
Wall

Install Drywall Panels

INSTALL DRYWALL WALL PANELS to manufacturers recommendations.
Typically start at a corner or intersection. Cut panels 3/8 less than the
measurement from the floor to the underside of the joists (or existing ceiling).
Position panels either vertically or horizontally, whichever gives fewer joints. Installing Metal Trims
Locate joints over studs. Avoid joints D-100 1 1/4 DRYWALL CORNER BEAD 90 & 130protects the outside corners. Allow one 8
on both sides of the same studs. Vertical Horizontal piece per corner. Press corner bead firmly onto the board surface and secure with drywall screws
Avoid joints directly above or through the small holes along the edge of the bead. Fasten on alternate sides every 6. Ensure
below openings for doors and fastener head is driven in below the nose of the corner bead.
windows. Screw Start
D-200 DRYWALL L TRIM protects the edge of drywall panels when butting up to concrete or other
centre at
At floor, support the panel at its first corner materials and at door and window openings when moulding is not being used. Available for both
centre on a 3/8 shim. Advance 1/2 and 5/8 drywall. Attach with drywall screws and finish with joint compound.
panels in the direction shown and D-400 METAL J TRIM provides edge protection at door and window openings and where drywall
keep panels plumb. Secure panels butts against concrete or other surfaces. Available for both 1/2 and 5/8 drywall. Finish by painting.
to studs with drywall screws.
Drive screws until panel is tight D-700 ANGLE FRAMING TRIM is an optional component used in framing around ductwork and columns.
against framing and screw is For the next and subsequent panels, apply in the following direction:
just below board surface without
breaking the face paper. INSTALL PANEL IN THIS DIRECTION
Installing Paper Trims
PAPER-FACED METAL DRYWALL BEADS AND TRIMS
Bulkheads Braced
bulkhead
Unbraced
bulkhead
an alternative to metal trims. Installation is comparable
to that of metal trims except no mechanical fasteners
CREATE A MINI-FRAMED WALL to box
are required. PLATINUM paper-based trims are
in ductwork and columns. Attach 1
D-700 quickly installed by embedding into
x 2 D-700 angle against wall section Angle
standard drywall joint compound.
under ductwork for underside drywall
to be fastened to. Fasten as required. Up to 24