8474L-000-STC-1390-001-3-Standard Auxiliary Piping Support - Hot Collection PDF

Project n - Unit Doc. type Mat. code Serial n Rev.
Page
8474L 000 STC 1390 001 3 1 / 27
VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

DUNG QUAT REFINERY (DQR) PROJECT
STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION
STANDARD AUXILIARY
PIPING SUPPORTS
HOT COLLECTION
Document Class: Z
Pages modified under this revision: 2, 21 TO 27
3 26-JUN-08 ISSUE FOR CONSTRUCTION Prashant T. G. Voisin D. C. AGARWAL

2 05-MAR-07 ISSUE FOR CONSTRUCTION Prashant T. G. Voisin D. C. AGARWAL
1 12-JUL-06 ISSUE FOR CONSTRUCTION C.Massif G. Voisin D. C. AGARWAL
0 19-APR-06 ISSUE FOR CONSTRUCTION C.Massif G. Voisin D. C. AGARWAL
A 29-DEC-05 ISSUE FOR REVIEW C.Massif G. Voisin D. C. AGARWAL
Rev Date STATUS WRITTEN BY CHECKED BY APPROVED BY
DD/MM/YY (name & visa) (name & visa) (name & visa)
DOCUMENT REVISIONS
Sections changed in last revision are identified by a vertical line in the margin
8474L-000-STC-1390-001-3.doc
Project n - Unit Doc. type Mat. code Serial n Rev. Page
8474L 000 STC 1390 001 3 2 / 27

CONTENTS
1. INTRODUCTION 3
2. MATERIALS SPECIFICATIONS FOR SUPPORT MEMBERS 4
3. HEAT TREATMENTS FOR WELDED SUPPORTS 6
4. STANDARD COLLECTION STRUCTURAL ELEMENTS 8
5. BOLTING AND SUPPORT ELEMENTS 9
6. TABLE 6 - PIPE SPAN NORMAL THK 10
7. TABLE 7 - PIPE SPAN THIN WALL 12
8. GUIDELINES FOR SUPPORTS OF SMALL BORE LINES AT SITE 14
9. STANDARD SUPPORTS SERIES 21
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 3 / 27

1. INTRODUCTION
The present document includes the list and revision index of the STANDARD AUXILIARY
PIPING SUPPORTS HOT COLLECTION.
IMPORTANT :
Standard support collection is in accordance with : SupportModelerss libraries
TP_STC_Euro_Hot_6
SYMBOLOGY:
WELDED ELEMENTS CLAMPED ELEMENTS HANGERS CONSTANT SPRING

GUIDE GUIDE RIGID STRUT
RESTING RESTING TIE-ROD
STOP STOP VARIABLE SPRING
STRUCTURAL BEAMS
PLATES
SMALL ELEMENTS
DIAMETER RESTRAINTS
SUPPORTS
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 4 / 27

2. MATERIALS SPECIFICATIONS FOR SUPPORT MEMBERS

TABLE 1
SUPPORTING ELEMENTS AS PER ASTM SPECIFICATION
SUPPORT
PIPING ELEMENT NOT WELDED TO PIPE BUT IN

MATCL
ELEMENT OUT OF THERMAL FLOW OR

ELEMENT WELDED TO PIPE CONTACT WITH PIPING THERMAL FLOW
COMPLETELY OUTSIDE OF INSULATION
OR INSIDE INSULATION
BOLTING SHAPES BOLTING
TEMP. PLATES PLATES
MATERIAL PIPE SHAPES PIPES SHAPES (BOLT & PIPES PLATE & (BOLT & FORGED
(C) & BARS & BARS
NUT) BARS NUT)
-29 TO -10 / A 516-60 / A 516-60
CS A 193/B7
C.S. -10 TO 343 A 36 (3) A 53-B A 36 (3)
A 53-B A 194/2H
343 TO 427 CH / A 387-11 / A387-11
C.S. A 53-B G A 36-G A 193/B7
(GALVANIZED)
-29 TO 100 CG Not used
(1)(2) (1)(2) A 194/2H A193/B7
A53-B A36 A668-D
A 193/B7 A194/2H
LTCS
-46 TO 427 CL A 333 GR.6 / A 516-60
A 53-B A 36
A 194/2H
A 193/B7
1 Cr - Mo -29 TO 343 AS A 53-B A 36
A 194/2H
2 Cr - 1 Mo A 335-P11 / A 387-11
A 193/B8
5 Cr - Mo 343 TO 650 AH A 335-P11 / A 387-11
A 194/8
(1) A sheet of insulating material (e.g. klingerite or similar material) at least 2 mm thick shall be inserted between support and pipe to avoid any direct contact.
(2) G denotes galvanized material.
(3) Carbon steel shapes, plates and bars ( A36 ) welded directly to the pipe shall have maximum Carbon content 0.23% and maximum Carbon Equivalent value 0.45%.
(4) Specified materials are minimum acceptable according to ASTM references. Contractor may use an equivalent material composition or upgraded for facilities of material
supply. Eg. A106 Gr.B pipe may be used in lieu of A53 Gr.B.
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 5 / 27

MATERIALS SPECIFICATIONS FOR SUPPORT MEMBERS ON CLASSIFIED HOT LINES
TABLE 1 ( continued )
SUPPORTING ELEMENTS AS PER ASTM SPECIFICATION

SUPPORT
PIPING ELEMENT NOT WELDED TO PIPE BUT IN

MATCL
ELEMENT OUT OF THERMAL FLOW OR

ELEMENT WELDED TO PIPE CONTACT WITH PIPING THERMAL FLOW
COMPLETELY OUTSIDE OF INSULATION
OR INSIDE INSULATION
BOLTING SHAPES BOLTING
TEMP. PLATES PLATES
MATERIAL PIPE SHAPES PIPES SHAPES (BOLT & PIPES PLATE & (BOLT & FORGED
(C) & BARS & BARS
NUT) BARS NUT)
SS A 53-B (1) A 36 (1) A 193/B7
-29 TO 343
AISI 304 / 304L A 312-Tp A240- A 194/2H
AISI 316 / 316L 304L T.304L A193/B7
-198 TO -29 / A53-B A36 A668-D
AISI 304H A 312-Tp A 240-T. A 320/B8 A194/2H
SH /
AISI 321 A 312-Tp A240- 304 304H A194/8
343 TO 650
304H T.304H
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 6 / 27

3. HEAT TREATMENTS FOR WELDED SUPPORTS

TABLE 2
ELEMENT WELDED TO PIPE WELDING HEAT TREATMENT (3) (4) (5)
SUPPORT
MATC L
PIPING
TEMP. PRE-HEATING (6) CONDITIONS
PLATES
MATERIAL (C) PIPE SHAPES P n CONDITION TEMP. NOT REQUIRING
& BARS
(2) REQUIRED C PWHT (7)
-29 TO 343 CS A 36
TS > 490 MPa
C.S. SA or SB < 38 mm
A 53-B or
343 TO 427 CH / A 387-11 80 or
SA or SB >
1 T < 16 mm
C.S. 25 mm
-46 TO -29 CL A 106-B / A 516-60
(LOW TEMP.)
C.S.
(GALVANIZED)
-29 TO 100 CG Not used - - -
-29 TO 343 AS A 335-P11 /

1 Cr - Mo A 387-11 4 150
SA or SB < 25.4 mm
343 TO 650 AH or T< 13 mm
-29 TO 343 AS TS < 490 MPa (8)
2 Cr - 1 Mo A 335-P11 / A 387-11 5 Not Required 175
343 TO 650 AH
5 Cr - Mo
-29 TO 343 AS A 335-P11 / A 387-11 5 175
T < 13 mm
TS < 490 MPa
343 TO 650 AH
AISI 304 /
304L
-29 TO 343 SS
AISI 316 / -198 TO 29 A 312 A 240
/ 8
316L TP 304 T.304
AISI 304H 343 TO 650
SH
AISI 321
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 7 / 27

Notes to the TABLE 2:
1) The requirements of this table are in accordance with those of ASME code B31.3.
2) Temperature indicated in the Mechanical Line List.
3) SA= support thickness; SB= piping thickness; T= throat thickness of fillet welds: TS= tensile strength.
4) The side of fillet welds shall be 8/10 of the smaller thickness to be welded.
5) Welding operations may not be performed with an ambient temperature of less than -20C.
6) For ambient temperature of less than 5C, preheating shall be carried out notwithstanding the required conditions.
7) When lines are heat-treated for process purposes, verify whether support-piping welds are to be
heat-treated notwithstanding material characteristics.
In all events, heat treatment shall be performed for caustic soda service.
8) Based on material service and corrosion and not on mechanical considerations, some piping materials may require PWHT (ref.
Doc. no. 8474L-000-JSS-6300-002). Pipe Supports for these fluid services shall follow the same PWHT requirement as the
pipes.
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 8 / 27

4. STANDARD COLLECTION STRUCTURAL ELEMENTS

TABLE 3
SHAPES
I-SHAPE H-SHAPE CHANNEL ANGLE
EURONORM CODE EQUIV. JIS EURONORM CODE EQUIV. JIS EURONORM CODE EQUIV. JIS EURONORM CODE EQUIV. JIS
IPE SECION HEA SECION UPN SECION L SECION
80 U8 75 * 40
100 I10 100 * 75 100 H10 100 * 100 100 U10 100 * 50 30*30*5 L3 30 * 30 * 4
120 I12 125 * 75 120 H12 125 * 125 120 U12 125 * 65 50*50*5 L5 50 * 50 * 5
140 H14 150 * 150 70*70*7 L7 70 * 70 * 7
160 I16 150 * 75 160 H16 175 * 175 160 U16 150 * 75 80*80*10 L8 80 * 80 * 8
100*100*10 L10 100 * 100 * 10
200 I20 200 * 100 200 H20 200 * 200 200 U20 200 * 80
240 I24 250 * 125 240 H24 250 * 250 240 U24 250 * 90
300 I30 300 * 150
Note to the TABLE 3
Shape indication on supports drawings, correspond to a conventional symbology as shown in the TABLE 3.
The TABLE 3 shows the equivalence with the EURONORM Standard.
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 9 / 27

5. BOLTING AND SUPPORT ELEMENTS
TABLE 4 : BOLTING AND FORGED PIECES SUPPORT ELEMENTS TABLE 5 : SUPPORT ELEMENTS
BOLTS STUD NUTS FORG RODS FLAT BARS PLATES

BOLTS
M LENGHT LENGHT M M DIAM THK BREADTH THK
2 2
6 6 5 30* 50 60 5
10 40* 70* 10* 10* 10 50 60 70 80 90
12 40 50 60 70 12 12 12 10 100 120 140 150 160 10
16 40 50 60 70 16 16 16 200 220 250 300 350
20 50 60 70 80 20 20 20 400 450 500
24 60 70 100 24 24 24 15 100 15
30 100 30 30 30 20 100 20
36 100 120 170 36 36 36 3 30*
* : SPECIFIC MATERIAL FOR PIPE DIA <2
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 10 / 27

6. TABLE 6 - PIPE SPAN NORMAL THK
PIPE SPAN TABLE FOR CARBON STEEL ( ALL SCH. ) , LOW AND INTERMEDIATE ALLOY STEEL ( ALL SCH. )
AND STAINLESS STEEL PIPES ( SCH. > 40 S )
MAXIMUM ALLOWED PIPE SPAN ( MM )

DIA. INCHES ( DN ) VAPOUR SERVICE LIQUID SERVICE
BARE INSULATED BARE INSULATED
1/2'' ( 15 ) 2500 2200 2500 2200
3/4'' ( 20 ) 2900 2300 2900 2300
1.0'' ( 25 ) 3300 2300 3300 2300
1.5'' ( 40 ) 4200 3200 4100 3100
2.0'' ( 50 ) 4900 3900 4700 3600
3.0'' ( 80 ) 6200 4900 5600 4400
4.0'' ( 100 ) 7100 5900 6200 5100
6.0'' ( 150 ) 8600 7500 7300 6300
8.0'' ( 200 ) 10100 8600 7600 6700
10.0'' ( 250 ) 11400 9800 8100 7300
12.0'' ( 300 ) 12400 10800 8400 7600
(4) (4)
14.0'' ( 350 ) 13000 12400 10600 9800( 4 )
16.0'' ( 400 ) 13900 13400( 4 ) 10900( 4 ) 10100( 4 )
18.0'' ( 450 ) 14700 14200( 4 ) 10300( 4 ) 9600( 4 )
20.0'' ( 500 ) 15600 15000( 4 ) 10500( 4 ) 9900( 4 )
24.0'' ( 600 ) 17000 16200 10800 10300
NOTES :
1. Spans have been calculated based on the pipe wall thickness provided in Piping Material Specification.
2. For SS pipes the spans are valid for pipe thickness > 40S only. For SS SCH 10S pipes separate span table shall be
referred to Table 7.
3. Spans are valid for a maximum design temperature of 400 Deg. C ( unless noted otherwise ). For temperature
above 400 Deg. C or line size above 24", span shall be calculated for by stress analysis.
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 11 / 27

4. For CS SCH10 thick pipes these spans are valid up to a maximum design temperature of 150 Deg. C only.
5. Indicated pipe spans are not valid for other metallic piping such as Aluminium Alloy, Monel etc.
6. Indicated pipe spans are not valid for non-metallic piping such as GRE , PVC etc.
7. Free draining lines with slope requirements require additional check for these spans.
8. Indicated pipe spans are valid for straight pipe runs only. For other piping configurations the spans shall be multiplied
by a suitable factor ( Refer to sample figures below ).
9. The criteria for maximum allowed pipe span is based upon the minimum span calculated as per the following :
- Maximum pipe deflection < 12.5 mm.
- Maximum longitudinal bending stress < 0.25 Sh ( Sh = Allowable stress at the maximum design temperature )
10. Following data has been used in the span calculations :
- Density of insulation = 190 Kg / m3
- Insulation Thickness: 15DN = 25mm , 20DN = 50MM , 25-50DN = 80mm , 80-100DN = 90mm , > 150DN = 100mm.
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 12 / 27

7. TABLE 7 - PIPE SPAN THIN WALL
PIPE SPAN TABLE FOR STAINLESS STEEL SCH 10S PIPES
MAXIMUM ALLOWED PIPE SPAN ( MM )

DIA. INCHES ( DN ) VAPOUR SERVICE LIQUID SERVICE
BARE INSULATED BARE INSULATED
2.0'' ( 50 ) 5400 3700 4800 3400
3.0'' ( 80 ) 6600 4800 5600 4100
4.0'' ( 100 ) 7500 5700 5900 4700
6.0'' ( 150 ) 9100 7200 6700 5500
8.0'' ( 200 ) 10400 8600 7200 6200
10.0'' ( 250 ) 11600 10000 7800 6900
12.0'' ( 300 ) 12700 11100 8300 7500
14.0'' ( 350 ) 13300 11700 8500 7800
16.0'' ( 400 ) 14200 12600 8700 8000
18.0'' ( 450 ) 15100 13400 8800 8200
20.0'' ( 500 ) 15900 14300 9500 9300
24.0'' ( 600 ) 17500 15900 10200 9700
NOTES :
1. Spans have been calculated based on the pipe wall thickness provided in Piping Material Specification.
2. Spans are valid for a maximum design temperature of 400 Deg. C. For temperature above
400 Deg. C, span shall be calculated by stress analysis.
3. Indicated pipe spans are valid for Stainless Steel SCH 10S pipes only and shall not be used for
other metallic or non-metallic piping.
4. Free draining lines with slope requirements require additional check for these spans.
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 13 / 27

5. Indicated pipe spans are valid for straight pipe runs only. For other piping configurations the spans shall be multip
by a suitable factor ( Refer to sample figures below ).
6. The criteria for maximum allowed span is based upon the minimum span calculated as per the following :
- Maximum pipe deflection < 12.5 mm.
- Maximum longitudinal bending stress < 0.25 Sh ( Sh = Allowable stress at the maximum design temperature )
7. Following data has been used in the span calculations :
- Density of insulation = 190 Kg / m3
- Insulation Thickness: 50DN = 80mm , 80-100DN = 90mm , > 150DN = 100mm.
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 14 / 27

8. GUIDELINES FOR SUPPORTS OF SMALL BORE LINES AT SITE
8.1 General
These guidelines are to be used at site for small bore lines (below 2) which do not show
engineered supports on IFC isometrics.
It has to be noted that some critical small bore lines may show support definition and location on
IFC isometrics. All supports and pipe routing of such critical lines shall be respected and any
change due to unavoidable reasons shall be approved by the Stress Engineer.
Refer Section 9 (page of ) for list of Standard Supports dedicated to small bore lines.
8.2 Typical support arrangement for piping 1-1/2 and lower
8.2.1 Rest Support

Horizontal rest supports must comply with the following criteria depending on service, material and
insulation.
All SS & CG line (uninsulated or PP insulated) shall rest directly on steel with SS/CG wedge or shim
plates as isolator between pipe and steel.
8.2.2 Allowable Horizontal Span

Pipe spans shall generally conform to PIPE SPAN (Table 6 page 10).
Provide guides at adequate number of locations to secure the pipe.
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 15 / 27

8.2.3 Allowable Vertical Span

The maximum allowable span between two consecutive vertical guides shall be:
C = 3000 mm for DIAM to 1
8.2.4 Allowable Corner Span

The maximum allowable horizontal span on corner pipe rack shall not be more than,
C = 800 mm for DIAM to
C = 1500 mm for DIAM 1 to 1
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 16 / 27

8.2.5 Allowable Span on Sleeper way

The maximum allowable horizontal span on sleeper way or pipe rack shall not be more than,
C = 2000 mm for DIAM to
C = 3500 mm for DIAM 1 to 1
MG03
MR04 - E
SP02 - 1
8.2.6 Supports on Pipe rack
MR02 - A
MR07 C
MG03 MR04 B
MR04 C
MR04 B
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 17 / 27

8.2.7 Supports on Hose / Utility stations
MR05 B
MS01
MR05 B
MR05 B
MG01
TYP. MR05 B
MR05 B
8.2.8 Supports on Trap stations / Valve Bypass
MR05 B
MR02 A
MR02 C
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 18 / 27

8.2.9 Supports on Equipments

All support structure shall be attached to vessel clips only.
Vessel clips shall be provided by the equipment vendor and reflected in the equipment drawing.
Support span as per maximum allowable vertical guide span, shall be considered for the design of
the vessel clips.
MR06 B
MR06 B
*
MR06 B
MR05 A
*
MR05 A
*
MR05 A
*
MR06 B
MR05 A
* As per available clips on vessel by vendor
8.2.10 Supports for steam tracing
MR05 A
MR02 E
MR02 A
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 19 / 27

8.2.11 Supports on Wall Mounted Piping
MR04 D
MG02 B
8.2.12 Supports on Structures
MR04 - C or SB05 - C MR08
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 20 / 27

SUPPORTS CONSTRUCTION
DRAWINGS LIST
AND REVISION INDEX
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 21 / 27

9. STANDARD SUPPORTS SERIES
STANDARD AUXILIARY HOT PIPING SUPPORTS COLLECTION

SUPPORT SERIES
.
R R
Document Ref.
Description e Date e Date
8474L-000-
v v
. .
A 14-Oct-05 2 05-Mar-07
STC-1390- 00 SYNOPTIC SUPPORTS SERIES 0 30-Mar-06 3 20-Jun-08
1 12-Jul-06
A 14-Oct-05 2 05-Mar-07
STC-1391- 00 WELDED SUPPORTS SERIES 0 30-Mar-06 3 20-Jun-08
1 12-Jul-06
A 14-Oct-05 2 05-Mar-07
STC-1392- 00 CLAMPED SUPPORTS SERIES 0 30-Mar-06 3 20-Jun-08
1 12-Jul-06
A 14-Oct-05 2 05-Mar-07
STC-1393- 00 HANGER SUPPORTS SERIES 0 30-Mar-06 3 20-Jun-08
1 12-Jul-06
A 14-Oct-05 2 05-Mar-07
STC-1394- 00 STRUCTURAL SUPPORTS SERIES 0 30-Mar-06 3 20-Jun-08
1 12-Jul-06
A 14-Oct-05 2 05-Mar-07
STC-1397- 00 SMALL DIA. SUPPORTS SERIES (1/2 to 1) 0 30-Mar-06 3 20-Jun-08
1 12-Jul-06
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 22 / 27

SYNOPTIC SUPPORTS SERIES
STANDARD AUXILIARY HOT PIPING SUPPORTS COLLECTION

SYNOPTICS
. Date
R R
Document Ref.
Description e Date e
8474L-000-
v v
. .
A 14-Oct-05 2 05-Mar-07
STC-1390-10 SYNOPTIC FOR CARBON STEEL LINES
0 30-Mar-06 3 20-Jun-08
Page A1 WITHOUT PWHT GL 01
1 12-Jul-06
SYNOPTIC FOR CARBON STEEL LINES A 14-Oct-05 2 05-Mar-07
STC-1390-10 0 30-Mar-06 3 20-Jun-08
Page A2 GALVANIZED - GL 02
1 12-Jul-06
STC-1390-10 0 30-Mar-06 3 20-Jun-08
Page A3 WITH PWHT GL 03
1 12-Jul-06
STC-1390-10 0 30-Mar-06 3 20-Jun-08
WITHOUT PWHT FOR HIGH
Page A4
TEMPERATURE SERVICES GL 04 1 12-Jul-06
SYNOPTIC FOR ALLOY STEEL LINES A 14-Oct-05 2 05-Mar-07
STC-1390-10 0 30-Mar-06 3 20-Jun-08
Page A5 WITHOUT PWHT GL 05
1 12-Jul-06
SYNOPTIC FOR ALLOY STEEL LINES A 14-Oct-05 2 05-Mar-07

STC-1390-10 0 30-Mar-06 3 20-Jun-08
WITHOUT PWHT FOR HIGH
Page A6
TEMPERATURE SERVICES GL 07 1 12-Jul-06
SYNOPTIC FOR STAINLESS STEEL LINES A 14-Oct-05 2 05-Mar-07
STC-1390-10 0 30-Mar-06 3 20-Jun-08
Page A7 GL 08
1 12-Jul-06
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 23 / 27

WELDED SUPPORTS SERIES
CODE AND SUPPORT SUPPORT

SUPPORT DESCRIPTION REV 0 REV 1 REV 2 REV 3
SERIAL N 8474L-000- MARK TYPE
STC 1391.22 WE00 ELEMENT SUPPORT DELETED X X X X
STC 1391.01 WE01 ELEMENT PROTECTION SHIELD FOR DIAM. 2 TO 60 X X X X
STC 1391.02 WE02 ELEMENT REINFORCING PAD FOR DIAM. 2 TO 24 X X X X
STC 1391.03 WE03 ELEMENT SHEAR LUG BEARING FOR DIAM. 2 TO 24 X X X X
STC 1391.04 WE04 ELEMENT WEDGE FOR DIAM 2 TO 24 X X X X
DOUBLE CLIPS FOR VERTICAL PIPE FOR DIAM 2 TO

STC 1391.06 WE06 ELEMENT X X X X
24
STC 1391.07 WE07 ELEMENT CLIP ON HORIZONTAL PIPE FOR DIAM 2 TO 24 X X X X
STC 1391.08 WE08 ELEMENT CLIP ON ELBOWS FOR DIAM 2 TO 24 X X X X
STC 1391.09 WG01 GUIDE GUIDE ON UNINSULATED PIPE FOR DIAM 2 TO 24 X X X X
STC 1391.10 WG02 GUIDE GUIDE ON PIPE SHOES FOR DIAM 2 TO 60 X X X X
GUIDE ON VERTICAL DUMMY LEGS FOR DIAM 2
STC 1391.11 WG03 GUIDE X X X X
TO 24
STC 1391.12-1/2 WG04 GUIDE HOLD DOWN GUIDE FOR DIAM 2 TO 24 X X X X
STC 1391.12-2/2 WG04 GUIDE HOLD DOWN GUIDE FOR DIAM 2 TO 24 X X X X
STC 1391.32 WR00 RESTING ONLY CONTACT WITH STEEL X X X X
STC 1391.13 WR01 RESTING VARIABLE HEIGHT SHOES FOR DIAM 2 TO 24 X X X X
STC 1391.14 WR02 RESTING SHOES HEIGHT 100 FOR DIAM 2 TO 24 X X X X
DOUBLE VARIABLE HEIGHT SHOES FOR DIAM 2 TO

STC 1391.15 WR03 RESTING X X X X
24
STC 1391.16 WR04 RESTING DOUBLE SHOES HEIGHT 100 FOR DIAM 2 TO 24 X X X X
STC 1391.17 WR05 RESTING VERTICAL DUMMY LEG FOR DIAM 2 TO 24 X X X X
HORIZONTAL DUMMY LEG ON BEND FOR DIAM 2
TO 24
STC 1391.19 WR07 RESTING TRUNNION ON VERTICAL PIPE FOR DIAM 2 TO 24 X X X X
STC 1391.20 WR08 RESTING VERTICAL SHAPE LEG FOR DIAM 2 TO 24 X X X X
STC 1391.21-1/2 WR09 RESTING ADJUSTABLE DUMMY LEG FOR DIAM 2 TO 24 X X X X
STC 1391.21-2/2 WR09 RESTING ADJUSTABLE DUMMY LEG FOR DIAM 2 TO 24 X X X X
STC 1391.23 WR10 RESTING ADJUSTABLE LEG FOR DIAM 2 TO 24 X X X X

VERTICAL SUPPORT ON PLATFORMS FOR DIAM 2
TO 24
STIFFENERS ON SMALL VALVES FOR DIAM 2 TO

24
STC 1391.27 WR14 RESTING WELDED SHOE FOR DIAM. 26 TO 60 X X X X
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 24 / 27

STC 1391.28 WR15 RESTING SHAPE ON VERTICAL PIPE FOR DIAM 2 TO 24 X X X X

STC 1391.29 WS01 STOP STOP ON UNINSULATED PIPE FOR DIAM 2 TO 24 X X X X
STC 1391.30 WS02 STOP STOP ON PIPE SHOES FOR DIAM 2 TO 60 X X X X
STC 1391.31 WS03 STOP STOP ON DUMMY LEG FOR DIAM 2 TO 24 X X X X
CLAMPED SUPPORTS SERIES

SERIAL N8474l-000- MARK TYPE
STC 1392.01 CE01 ELEMENT CLAMP FOR HORIZONTAL PIPE FOR DIAM 2 TO 24 X X X X
STC 1392.02 CE02 ELEMENT CLAMP FOR TRUNNIONS & CLIPS FOR DIAM 2 TO 24 X X X X
STC 1392.03 CE03 ELEMENT CLAMP FOR DUMMY LEGS FOR DIAM 2 TO 24 X X X X
STC 1392.05 CE05 ELEMENT CLAMP ON HORIZONTAL PIPE FOR DIAM 2 TO 24 X X X X
STC 1392.07 CE07 ELEMENT RISER CLAMP FOR DIAM 2 TO 24 X X X X
STC 1392.09 CG01 GUIDE NO GRIPPED U-BOLT FOR DIAM 2 TO 24 X X X X

STC 1392.10 CR01 RESTING VARIABLE HEIGHT SHOES FOR DIAM 2 TO 24 X X X X
STC 1392.11 CR02 RESTING SHOES HEIGHT 100 FOR DIAM 2 TO 24 X X X X
STC 1392.12 CR03 RESTING DOUBLE VARIABLE HEIGHT SHOES FOR DIAM 2 TO 24 X X X X
STC 1392.13 CR04 RESTING DOUBLE SHOES HEIGHT 100 FOR DIAM 2 TO 24 X X X X
STC 1392.14 CR05 RESTING VERTICAL DUMMY LEG FOR DIAM 2 TO 24 X X X X
STC 1392.16 CR07 RESTING TRUNNION FOR DIAM 2 TO 24 X X X X

STC 1392.17 CR08 RESTING VERTICAL SHAPE LEG FOR DIAM 2 TO 24 X X X X
STC 1392.18 CR09 RESTING ADJUSTABLE DUMMY LEG FOR DIAM 2 TO 24 X X X X
STC 1392.19 CR10 RESTING CLIPS FOR ADJUSTABLE LEG FOR DIAM 2 TO 24 X X X X
STC 1392.20 CR11 RESTING VERTICAL SUPPORT ON PLATFORMS FOR DIAM 2 TO 24 X X X X
STC 1392.22 CR13 RESTING STIFFENERS ON SMALL VALVES FOR DIAM 2 TO 24 X X X X

STC 1392.23 CS01 STOP GRIPPED U-BOLT FOR DIAM 2 TO 24 X X X X
STC 1392.24 CS02 STOP STOP ON UNINSULATED PIPE FOR DIAM 2 TO 12 X X X X
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 25 / 27

HANGER SUPPORTS SERIES

STC 1393.01 HC01 CONSTANT SPRING SINGLE CONSTANT SPRING HANGER X X X X

STC 1393.02 HC02 CONSTANT SPRING DOUBLE CONSTANT SPRING HANGER X X X X
STC 1393.03 HC03 CONSTANT SPRING SINGLE CONSTANT SPRING BASE X X X X
STC 1393.04 HR01 RIGID STRUT SINGLE RIGID STRUT X X X X
STC 1393.05 HR02 RIGID STRUT DOUBLE RIGID STRUTS X X X X
STC 1393.06 HT01 TIE-ROD SINGLE TIE-ROD HANGER X X X X
STC 1393.07 HT02 TIE-ROD DOUBLE TIE-ROD HANGERS X X X X
STC 1393.08 HV01 VARIABLE SPRING SINGLE VARIABLE SPRING HANGER X X X X
STC 1393.09 HV02 VARIABLE SPRING DOUBLE VARIABLE SPRING HANGER X X X X
STC 1393.10 HV03 VARIABLE SPRING SINGLE VARIABLE SPRING BASE X X X X
STC 1393.11 HV04 VARIABLE SPRING DOUBLE VARIABLE SPRING BASE X X X X
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 26 / 27

STRUCTURAL SUPPORTS SERIES

STC 1394.01 SB01 BEAM DEPTH X X X X

STC 1394.02 SB02 BEAM COLUMN X X X X
STC 1394.03 SB03 BEAM T-SHAPE STRUCTURE X X X X
STC 1394.04-1/2 SB04 BEAM L-SHAPE STRUCTURE X X X X
STC 1394.04-2/2 SB04 BEAM L-SHAPE STRUCTURE X X X X

STC 1394.05 SB05 BEAM CHAIR STRUCTURE X X X X
STC 1394.06 SB06 BEAM U-SHAPE STRUCTURE X X X X
STC 1394.07 SB07 BEAM SUPPLEMENTARY BEAM SPAN X X X X
STC 1394.08 SB08 BEAM SINGLE BRACKET X X X X
STC 1394.09 SB09 BEAM DOUBLE BRACKET FOR VERT. PIPE 2 TO 6. X X X X
STC 1394.10 SB10 BEAM LATERAL FIXED BRACKET FOR VERT. PIPE 2 TO 6 X X X X
STC 1394.11 SB11 BEAM BRACKET FOR VERT. PIPE 2 TO 6 X X X X

STC 1394.12 SB12 BEAM DOUBLE BRACKET FOR VERT. PIPE 8 TO 24 X X X X
STC 1394.13 SB13 BEAM BIDIRECTIONAL VERT. GUIDE FOR DIAM 2 TO 6 X X X X
STC 1394.14-1/2 SB14 BEAM BIDIRECTIONAL VERT. GUIDE FOR DIAM 8 TO 24 X X X X
STC 1394.14-2/2 SB14 BEAM BIDIRECTIONAL VERT. GUIDE FOR DIAM 8 TO 24 X X X X
STC 1394.15-1/2 SB15 BEAM UNIDIRECTIONAL VERT. GUIDE FOR DIAM 2 TO 24 X X X X
STC 1394.15-2/2 SB15 BEAM UNIDIRECTIONAL VERT. GUIDE FOR DIAM 2 TO 24 X X X X
STC 1394.16 SB16 BEAM COMMON BRACKET GUIDE X X X X

STC 1394.17 SB17 BEAM COMMON DOUBLE BRACKET GUIDE X X X X
DOUBLE BRACKET FOR MULTIPLE VERT. PIPES 2 TO
STC 1394.18 SB18 BEAM X X X X
24
STC 1394.19 SP01 PLATE BASE PLATE FOR UNPAVED AREA DELETED
STC 1394.20 SP02 PLATE BASE PLATE FOR PAVED AREA X X X X
STC 1394.21-1/2 SP03 PLATE BOLTING PLATE ON CONCRETE X X X X
STC 1394.21-2/2 SP03 PLATE BOLTING PLATE ON CONCRETE X X X X
STC 1394.22 SP04 PLATE BASE PLATE ON STEEL SHAPES X X X X
STC 1394.23 SP05 PLATE BASE FOR SPRING BASES X X X X
STC 1394.24 SP06 PLATE ANTIFRICTION SLIDING PLATE X X X X
8474L-000-STC-1390-001-3.doc
8474L 000 STC 1390 001 3 27 / 27

SMALL DIA. SUPPORTS SERIES ( to 1)

SUPPORT DESCRIPTION REV0 REV1 REV2 REV3
STC 1397.01 ME01 ELEMENT CLAMPS X X X X

STC 1397.02 ME02 ELEMENT WELDED CLIPS X X X X
STC 1397.03 ME03 ELEMENT THREADED ANCILLARY X X X X
STC 1397.04 ME04 ELEMENT WEDGE X X X X
STC 1397.06 MG01 GUIDE GUIDE ON UNINSULATED HORIZ. PIPE X X X X

STC 1397.07 MG02 GUIDE GUIDE ON PIPE SHOES X X X X
STC 1397.08 MG03 GUIDE U-BOLT NO GRIPPED X X X X
STC 1397.09 MR01 REST SHOES X X X X
STC 1397.10 MR02 REST VERTICAL DUMMY LEG X X X X
STC 1397.12 MR04 REST BEAM SUPPORT X X X X

STC 1397.13 MR05 REST BEAM SUPPORT WITH GUIDE X X X X
STC 1397.14 MR06 REST SUPPORT ON VERTICAL PIPE X X X X
STC 1397.15 MR07 REST PICK-UP X X X X
STC 1397.16 MR08 REST TIE-ROD HANGERS X X X X
STC 1397.17 MS01 STOP U-BOLT GRIPPED X X X X
STC 1397.18 MS02 STOP CLAMPED STOP X X X X
STC 1397.19 MS03 STOP STOP FOR HORIZONTAL PIPE X X X X
8474L-000-STC-1390-001-3.doc

8474L-000-STC-1390-001-3-Standard Auxiliary Piping Support - Hot Collection PDF

Uploaded by

Copyright:

Available Formats

8474L-000-STC-1390-001-3-Standard Auxiliary Piping Support - Hot Collection PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

8474L-000-STC-1390-001-3-Standard Auxiliary Piping Support - Hot Collection PDF

Uploaded by

Copyright:

Available Formats

What are the different types of structural supports described in the document?

What are the different types of structural supports described in the document?

What materials are specified for different types of supporting elements?

What materials are specified for different types of supporting elements?

Project n - Unit Doc. type Mat. code Serial n Rev.

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

Pages modified under this revision: 2, 21 TO 27

3 26-JUN-08 ISSUE FOR CONSTRUCTION Prashant T. G. Voisin D. C. AGARWAL

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

2. MATERIALS SPECIFICATIONS FOR SUPPORT MEMBERS 4

3. HEAT TREATMENTS FOR WELDED SUPPORTS 6

4. STANDARD COLLECTION STRUCTURAL ELEMENTS 8

5. BOLTING AND SUPPORT ELEMENTS 9

6. TABLE 6 - PIPE SPAN NORMAL THK 10

7. TABLE 7 - PIPE SPAN THIN WALL 12

8. GUIDELINES FOR SUPPORTS OF SMALL BORE LINES AT SITE 14

9. STANDARD SUPPORTS SERIES 21

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

WELDED ELEMENTS CLAMPED ELEMENTS HANGERS CONSTANT SPRING

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

2. MATERIALS SPECIFICATIONS FOR SUPPORT MEMBERS

PIPING ELEMENT NOT WELDED TO PIPE BUT IN

ELEMENT OUT OF THERMAL FLOW OR

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

MATERIALS SPECIFICATIONS FOR SUPPORT MEMBERS ON CLASSIFIED HOT LINES

SUPPORTING ELEMENTS AS PER ASTM SPECIFICATION

PIPING ELEMENT NOT WELDED TO PIPE BUT IN

ELEMENT OUT OF THERMAL FLOW OR

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

3. HEAT TREATMENTS FOR WELDED SUPPORTS

-29 TO 343 AS A 335-P11 /

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

Notes to the TABLE 2:

2) Temperature indicated in the Mechanical Line List.

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

4. STANDARD COLLECTION STRUCTURAL ELEMENTS

The TABLE 3 shows the equivalence with the EURONORM Standard.

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

5. BOLTING AND SUPPORT ELEMENTS

BOLTS STUD NUTS FORG RODS FLAT BARS PLATES

* : SPECIFIC MATERIAL FOR PIPE DIA <2

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

6. TABLE 6 - PIPE SPAN NORMAL THK

MAXIMUM ALLOWED PIPE SPAN ( MM )

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

VIETNAM OIL AND GAS CORPORATION ( PETROVIETNAM )

STANDARD AUXILLIARY PIPING SUPPORTS HOT COLLECTION

7. TABLE 7 - PIPE SPAN THIN WALL