Scribd
Upload
45 views2 pages

7.1 Introduction To SMP:: But Recently More Complex Shape Structures Are Achievable

SMPs are polymers that have the ability to return to their original shape after being deformed by an external stimulus such as heat or light. SMPs contain both crystalline and amorphous regions, and their shape memory ability is due to changes between these states. When heated above the glass transition temperature, the crystalline regions become amorphous and flexible, allowing deformation. Upon cooling below this temperature while still deformed, the structure fixes in the new shape. However, heating again above the transition temperature causes the polymer chains to return to their original, programmed conformation due to stored internal stresses. This unique property makes SMPs useful for applications requiring reversible shape change.

Uploaded by

Nera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
45 views2 pages

7.1 Introduction To SMP:: But Recently More Complex Shape Structures Are Achievable

SMPs are polymers that have the ability to return to their original shape after being deformed by an external stimulus such as heat or light. SMPs contain both crystalline and amorphous regions, and their shape memory ability is due to changes between these states. When heated above the glass transition temperature, the crystalline regions become amorphous and flexible, allowing deformation. Upon cooling below this temperature while still deformed, the structure fixes in the new shape. However, heating again above the transition temperature causes the polymer chains to return to their original, programmed conformation due to stored internal stresses. This unique property makes SMPs useful for applications requiring reversible shape change.

Uploaded by

Nera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

English:

7.1 Introduction to SMP:


SMP are compound plastics polymers that have a special chemical
structure that gives the ability to return from a deformed shape
(temporary state) to their original (programmed) state induced by an
external stimulus in the form of heat, light, electricity or magnetism,
usually all these stimuli generate heat with in the polymer to activate.
Shape Memory Polymers usually retain two shapes, (the deformed shape
and the original programmed shape) but recently more complex shape
structures are achievable

Polymers are molecules that are made up of large number of repeating


structural subunits which are connected together by chemical bonds
either covalent or ionic and, in shape memory polymers covalent bonds
are found.

Polymers are found to occur in two states, a Crystalline state and an


Amorphous state (Figure1) where when in a crystalline state it is
organised uniformly and becomes a rigid and stronger structure, and
when in the amorphous state the polymers subunits are randomly
scattered and are soft and flexible and able to move around relatively
freely.

A shape memory polymer has a semi-14 crystalline structure where both


states occur at the same time within a specific temperature, usually room
temperature.
(Figure 4: The Crystalline state at A and at B Tg:A is 170C lower than Tg:B
200C [7] )
A Glass Transition Temperature (Tg) is when the polymer changes from
one state to the other i.e. from crystalline state to amorphous due to the
increase in heat energy. SMPs have two glass transition temperatures A
and B. With reference to figure (4), area A has a lower glass transition
temperature than area B. In the crystalline state all movements of the
polymer segments are frozen. The increase of temperature means that
the rotation around the segment bonds becomes increasingly unimpeded.
After heating, internal stresses (strain storage) inside the polymers react
elastically causing the polymer to recover to its original (programmed)
state (Figure 4). SMPs have an elongation capabilities of over 400% to its
size and with an accuracy when reforming of 99%.

When a shape memory polymer is heated above the first glass transition
temperature (Tg) the crystalline region is transformed to the amorphous
state and becomes flexible and extendable (show in a).
A load is then applied and the specimen of SMP extends, while its under
heat (path a-b). The specimen is then cooled when its deformed to a
temperature under its first glass transition temperature (path b-c) and the
amorphous region then changes back to the crystalline state.

The specimen will be fixed to its new deformed state, but due to internal
stresses of the uncrystallized amorphous region the specimen will contract
to a small extent (path c-d).

If the specimen is then heated again to a temperature above its first Tg


with no load on, the specimen will then return to is original shape
(programmed state).

The speed in which this polymer returns to its programmed structure is


limited by the friction generated within the molecular structure.

A non-covalent interaction differs from a covalent bond in that it does not involve the
sharing of electrons, but rather involves more dispersed variations of
electromagneticinteractions between molecules or within a molecule.

You might also like