Operating Instructions

Parts List

SYC Series Hand Stacker

Note: Owner and operator MUST read and understand this
0
operating instructions before use this pallet truck.

Welcome to use our hand stacker HSYC series. Your stacker is made of high quality steel
and was designed to give a durable, reliable and easy to use product. For your safety and
correct operation, please carefully read this instruction book and warnings on the stacker
before using it.

NOTE: All of the information reported herein is based on data available at the
moment of printing. The factory reserves the right to modify its own products at any
moment without notice and incurring in any sanction. So, it is suggested to always
verify possible updates.

1. STRUCTURAL DATA FORM

SYC1016 SYC1516 SYC2016 SYC1020/25/ SYC1520/25/
Model
30 30
Capacity Kg 1000 1500 2000 1000 1500
Lift Height mm 1600 1600 1600 2000/2500/ 2000/2500/
3000 3000
Fork Length mm 900/1000/1150 900/1000/1150 900/1000/1150 900/1000/1150 900/1000/1150
Width overall mm 320-740/550 320-740/550 320-740/550 320-740/550 320-740/550
Forks
Overall Height mm 2060 2060 2060 2060 2060
Min. Fork Height mm 85 85 85 85 85

2. Installation & Adjustment

*To prevent oil-leaking from oil tank during transportation. Air Screw (part No.F249) is
replaced with oil-sealing screw in the factory but it has to be replaced back when you put
this stacker in use.
*How to change: screw out oil-sealing Screw, then screw in Air Screw which is in the
spare parts bag, thus keep oil tank always connecting with atmosphere.

3. SAFETY GUIDANCE
3.1 Operator should read all warning signs and instructions here and on the stacker
before using it.
3.2 Do not operate a hand stacker unless you are familiar with it and have been trained
or authorized to do so.
3.3 Do not operate a hand stacker unless you have checked its condition. Give special
attention to the wheels, the handle, the guide frame, the pilot wheel, the doorframe,
etc.
1
3.4 Do not use it on a slopping ground.
3.5 Do not take up any people on the forks.
3.6 The operator had better take on gloves for labor protecting.
3.7 When the goods have been transported or lifted, all people should be away form the
forks for 600mm.
3.8 Do not load over maximum capacity.
3.9 The weight of goods should be distributed on the two forks, do not use only one
fork. The center of gravity of goods should be in the center of two forks.
3.10 People forbid standing under the forks.
3.11 Do not move the hand stacker when the goods are lifted to the height more than
300mm.
3.12 At other special condition or place, the operator should be carefully to operate the
hand stacker.

4. MAINTENANCE
4.1 Hydraulic oil
Please check the oil level every six months. The oil can be hydraulic oil: ISO VG32, its
viscosity should be 32cSt at 40oC, total volume is about 2.0lt.
4.2 Daily check and maintenance
It is necessary to check the hand stacker daily. Special attention should be paid to the
wheels, the axles, as thread, rags, etc., it may block the wheels, the fork and the mast
should be checked, too. The forks should be unloaded and lowered in the lowest position
when the job is over.
4.3 Lubrication
Use motor oil or grease to lubricate all movable parts.
4.4 Remove the air
The air may enter the hydraulic pump during the transportation after the customer buys
it. It will cause the piston rod to fail to keep up the raised height. The air can be removed
in the following way: pull the control handle (FS107) up and move handle (FS110) up and
down for several times.

5. TO ADJUST RELEASE DEVICE

On the draw-bar of this hand stacker, you can find the control handle (FS107) which can
be regulated in three positions: LOWER = to lower the forks; NEUTRAL = to move the
load, and LIFT = to raise the fork. These three positions have been pre-posited at the
factory. If however they have been changed, you can adjust according to following step:
4.1 If the forks elevate while pumping in the NEUTRAL position, turn the adjusting nut
(FS116) on the adjusting bolt (FS115) clockwise or turn the adjusting screw (F229)
clockwise until pumping action does not raise the forks and the NEUTRAL position
functions properly.
4.2 If the forks descend while pumping in the NEUTRAL position, turn the nut (FS116) or
the screw (F229) counter-clockwise until the forks do not lower.
2
4.3 If the forks do not descent when the control handle (FS107) is in the LOWER position,
turn the nut (FS116) or the screw (F229) clockwise until raising the control handle (FS107)
lowers the forks. Then check the NEUTRAL position according to item 4.1 and 4.2 to be
sure the nut (FS116) and the screw (F229) is in the proper position.
4.4 If the forks do not elevate while pumping in the LIFT position, turn the nut (FS116) or
the screw (F229) counter-clockwise until the forks elevate while pumping in the LIFT
position. Then check the LOWER and NEUTRAL position according to item 4.1, 4.2 and
4.3.
6. TROUBLES SHOOTING
No Trouble Clause Fixing Methods
1 The forks can not - The hydraulic oil is not - Pour in the oil.
be up the max. enough.
height.
- Without hydraulic oil. - Fill in the oil.
- The oil has impurities. - Change the oil.
2 The forks can not - The nut (FS116) is too high - Adjust the nut (FS116) or the
be lifted up. or the screw (F229) is too screw (F229) .(see item 4.4)
close, keep the pumping valve
open. - Banish the air.(see item 3.4)
- Air comes into the hydraulic
oil.
- The piston rod(F248) or - Replace it.
pump body(F225) or the mast
(F346) is deformed resulting
from loading slanting to one
The forks can not side or over-loading.
3 be descended. - The fork was kept in the high
position for long time with - Keeping the fork in the
piston rod bared to arise in lowest position if not using,
rusting and jamming of the and pay more attention to
rod. lubricate the rod.
- The adjusting nut (FS116) or
the screw (F229) is not in the - Adjust the nut (FS116) or
correct position. the screw (F229). (see item
- The rollers (F327) are not 4.3)
lubricated. - Lubricate its.
- Sealing parts worn or - Replace with the new one.
4 Leaks damaged.
- Some part cracked or worn - Replace with the new one.
into small.

3
 - The impurities in the oil - Replace with new oil.
cause the release valve to be
unable to close tight.
5 The fork descends - Some parts of hydraulic - Inspect and replace the
without the release system is cracked or bored. waste parts.
valve worked. - Air comes into the oil. -Banish the air. (See item 3.4)
- Sealing parts worn or - Replace with the new one.
damaged.
- The adjusting nut (FS116) or - Adjusting the nut (FS116) or
the screw (F229) is not in the the screw (F229). (See item
correct position. 4.2)

NOTE: DO NOT ATTEMP TO REPAIR THE PALLET TRUCK UNLESS YOU

ARE TRAINED AND AUTHORIZED TO DO SO.

4
5
 Handle Part List
No. Description Qty. No. Description Qty.
FS101 Spring 1 FS109 Elastic Pin 1
FS102 Bldae Spring 1 FS110 Handle 1
FS103 Elastic Pin 1 FS111 Pull Board 1
FS104 Elastic Pin 1 FS112 Pin 1
FS105 Rubber Washer 1 FS113 Release Rod 1
FS106 Roller 1 FS114 Chain 1
FS107 Control Handle 1 FS115 Adjusting Bolt 1
FS108 Elastic Pin 1 FS116 Adjusting Nut 1

6
7
 Pump Part List for SYC1016;1516;2016;1025;1030;
No. Description Qty. No. Description Qty.
F201 Pump Piston Rod 1 F229 Screw 1

F202 Spring Washer 1 F230 Nut 1

F203 Spring 1 F231 Spring 1

F204 Dust Ring 1 F232 Strike Pin 1

F205 Seal 1 F233 O-Ring 2

F206 Bushing 2 F234 Dust Catcher 1

F207 Screw 3 F235 Cover with Screw 1

F208 Washer 3 F236 Seal Washer 1

F209 Spring Washer 3 F237 Adjusting Bolt 1

F210 Bracket 1 F238 Spring 1

F211 Shaft for Roller 1 F239 Spring Seat 1

F212 Screw 1 F240 Steel Ball 1

F213 Shaft 1 F241 Seal Washer 1

F214 Pressure Roller 1 F242 Screw 1

F215 Lever of Pedal 1 F243 Locking Ring 1

F216 Elastic Pin 1 F244 Y-Ring 1

F217 Screw 1 F245 Support Ring 1

F218 Seal Washer 1 F246 Piston 1

F219 Spring 1 F247 O-Ring 2

F220 Steel Ball 1 F248 Lifting Piston Rod 1

F221 Valve Spindle of Pump 1 F249 Screw 1

F222 Seat of pump Valve 1 F250 Screw 1

F223 O-Ring 1 F251 Conduit 1

F224 Washer 1 F252 O-Ring 2

F225 Body of Pump 1 F253 Cover with Screw 1

F226 Locking Ring 1 F254 Dust Ring 1

F227 Elastic Pin 1 F262 Spring 2

F228 Lever Plate 1

8
9
 Pump Part List for SYC1016;1516;1025;1030; Fast Lifting
No. Description Qty. No. Description Qty.
F201 Pump Piston Rod 1 F235 Cover with Screw 1
F202 Spring Washer 1 F236 Seal Washer 1
F203 Spring 1 F237 Adjusting Bolt 1
F204 Dust Ring 1 F238 Spring 1
F205 Seal 1 F239 Spring Seat 1
F206 Bushing 2 F240 Steel Ball 1
F207 Screw 3 F241 Seal Washer 1
F208 Washer 3 F242 Screw 1
F209 Spring Washer 3 F243 Locking Ring 1
F210 Bracket 1 F244 Y-Ring 1
F211 Shaft for Roller 1 F245 Support Ring 1
F212 Screw 1 F246 Piston 1
F213 Shaft 1 F247 O-Ring 2
F214 Pressure Roller 1 F248 Lifting Piston Rod 1
F215 Lever of Pedal 1 F249 Screw 1
F216 Elastic Pin 1 F250 Screw 1
F217 Screw 1 F251 Conduit 1
F218 Seal Washer 1 F252 O-Ring 2
F219 Spring 1 F253 Cover with Screw 1
F220 Steel Ball 1 F254 Dust Ring 1
F221 Valve Spindle of Pump 1 F255 Pump Piston Rod 1
F222 Seat of pump Valve 1 F256 O-Ring 1
F223 O-Ring 1 F257 Steel Ball 2
F224 Washer 1 F258 Washer 1
F225 Body of Pump 1 F259 Screw 1
F226 Locking Ring 1 F260 Pumping Cylinder 1
F227 Elastic Pin 1 F261 Seal Washer 1
F228 Lever Plate 1 F262 Spring 2
F229 Screw 1 F263 Steel Ball 1
F230 Nut 1 F264 Spring 2
F231 Spring 1 F265 Spring 1
F232 Strike Pin 1 F266 Pin 1
F233 O-Ring 2 F267 Spring 1
F234 Dust Catcher 1 F268 Cap of Spring 1

10
11
 Mast Part List for SYC1025;1030;
No. Description Qty. No. Description Qty.
101 Reticulation 1 132 Shaft 1
102 Screw 6 133 Cam 1
103 Clip 6 134 Washer 4
104G Mast 1 135 Shaft of Roller 2
105 Hoop 1 136 Roller 2
106 Nut 3 137 Locking Ring for Axle 14
107 Nut 2 138 Screw 8
108 Bolt 1 139 Nut 8
109 Bolt 1 140 Linking Plate 1
110 Elastic Washer 1 141 Screw 4
111 Washer 1 142 Locking Ring for Hole 4
112 Bearing 2 143 Bearing 8
113 Bearing 2 144 Roller 4
114 Frame of Wheel 1 145 Locking Ring 8
115 Nut 2 146 Steel Ball 8
116 Elastic Washer 2 147G Fixed Fork 4
117 Axle 2 148 Nut 4
118 Washer 8 149 Bolt 2
119 Nut 1 150 Connect 2
120 Wheel 2 151 Chain 2
121 Bearing 8 152 Roller for Chain 2
122 Screw 2 153 Inner Mast 1
123 Frame of Wheel with 1 154 Screw 4
124 Brake
Brake Plate 1 155 Axle 4
125 Spring 1 156 Elastic Pin 1
126 Cover 1 157 Frame 4
127 Nut 1 158 Wheel 2
128 Nut 1 159 Bolt 4
129 Screw 1 160 Axle 2
130 Pedal 1 161 Locking Ring for Hole 2
131 Elastic Pin 1

12
13
 Mast Part List for SYC1016;1516;2016;
No. Description Qty. No. Description Qty.
F301 Bolt 1 F331 Locking Ring 4
F302 Elastic Washer 1 F334 Bolt 4
F303 Washer 1 F335 Nut 4
F304 Bearing 2 F336 Fork 2
F305 Bearing 2 F337 Locking Ring 4
F306 Frame of Wheel 1 F338 Bearing 4
F307 Nut 2 F339 Roller 4
F308 Elastic Washer 2 F340 Locking Ring 4
F309 Axle of Wheel 2 F341 Steel Ball 4
F310 Cover 4 F342 Connect 2
F311 Bearing 4 F343 Chain 2
F312 Wheel 2 F344 Nut 2
F313 Screw 2 F345 Bolt 1
F314 Frame of Wheel With Brake 1 F346 Mast 1
F315 Washer 1 F347 Reticulation 1
F316 Nut 1 F348 Clip 6
F317 Brake Plate 1 F349 Screw 6
F318 Spring 1 F350 Hoop to Holding Pump 1
F319 Cover 1 F351 Nut 3
F320 Nut 1 F352 Nut 2
F321 Nut 1 F353 Bolt 1
F322 Screw 1 F354 Locking Ring 2
F323 Footplate 1 F355 Roller for Chain 2
F324 Elastic Pin 1 F356 Bearing 2
F325 Pin 1 F357 Locking Ring 2
F326 Cam 1 F358 Axle 1
F327 Roller 2 F359 Elastic Pin 1
F328 Bearing 4 F360 Frame 1
F329 Cover 4 F361 Elastic Washer 3
F330 Axle of Loading Roller 2

14
 ADJUSTED FORK LIST
No. Description Qty.
1 Locking Ring 1
2 Long Axle 1
3 Locking Ring 1
4 Adjusting Fork 2
5 Nut 4
6 Bolt 4
7 Frame Carriage 1
8 Locking Ring for Hole 4
9 Bearing 4
10 Roller 4
11 Locking Ring 4
12 Steel Ball 4
13 Bolt 2

15